Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Geophysical Investigations Map”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61Linked to original sources
USGS2016

Archive of bathymetry and backscatter data collected in 2014 nearshore Breton and Gosier Islands, Breton National Wildlife Refuge, Louisiana

As part of the Barrier Island Monitoring Project, scientists from the U.S. Geological Survey (USGS) St. Petersburg Coastal and Marine Science Center conducted nearshore geophysical surveys off Breton and Gosier Islands, Louisiana, in July and August of 2014. To assist the United States Fish and Wildlife Service (USFWS) with restoration planning efforts, the USGS was tasked with answering fundamental questions about the physical environment of the southern Chandeleur Islands, including the geology, morphology, and oceanography. Baseline data needed to answer these questions were either insufficient or missing. The USGS conducted a comprehensive geologic investigation in the summer of 2014, collecting geophysical and sedimentological data. Breton Island, located at the southern end of the Chandeleur Island chain in southeastern Louisiana, was recognized as a natural, globally significant nesting sanctuary for several bird species and was established as the Breton National Wildlife Refuge (NWR) in 1904. The areal extent of Breton Island has diminished 90 percent since 1920. Land loss is attributed to ongoing relative sea-level rise, diminished sediment supply, and storm impacts. The bird population on Breton Island has also declined over the years, most notably after Hurricane George in 1998 and after Hurricane Katrina in 2015; the latter completely submerged the island. Despite decreasing habitable acreage, migratory seabirds continue to return and nest on Breton Island. To prevent the island from being submerged in the future, and to protect, stabilize, and provide more nesting and foraging areas for the bird population, the USFWS proposed a restoration effort to rebuild Breton Island to its pre-Katrina footprint. This data series serves as an archive of processed interferometric swath and single-beam bathymetry data, and side-scan sonar data, collected in the nearshore of Breton and Gosier Islands, NWR, Louisiana. The data were collected during two USGS cruises (USGS Field Activity Numbers 2014-314-FA and 2014-317-FA) in July and August 2014. Geographic information system data products include a 100-meter-cell-size interpolated bathymetry grid, trackline maps, and point data files. Additional files include error analysis maps, Field Activity Collection System logs, and formal Federal Geographic Data Committee metadata. NOTE: These data are scientific in nature and are not to be used for navigation. Any use of trade names is for descriptive purposes only and does not imply endorsement by the U.S. Government.

Louisiana↗
USGS1994

Contributions to a shallow aquifer study by reprocessed seismic sections from petroleum exploration surveys, eastern Abu Dhabi, United Arab Emirates

The US Geological Survey, in cooperation with the National Drilling Company of Abu Dhabi, is conducting a 4-year study of the fresh and slightly saline groundwater resources of the eastern Abu Dhabi Emirate. Most of this water occurs in a shallow aquifer, generally less than 150 m deep, in the Al Ain area. A critical part of the Al Ain area coincides with a former petroleum concession area where about 2780 km of vibroseis data were collected along 94 seismic lines during 1981–1983. Field methods, acquistion parameters, and section processing were originally designed to enhance reflections expected at depths ranging from 5000 to 6000 m, and subsurface features directly associated with the shallow aquifer system were deleted from the original seismic sections. The original field tapes from the vibroseis survey were reprocessed in an attempt to extract shallow subsurface information (depths less than 550 m) for investigating the shallow aquifer. A unique sequence of reproccessing parameters was established after reviewing the results from many experimental tests. Many enhancements to the resolution of shallow seismic reflections resulted from: (1) application of a 20-Hz, low-cut filter; (2) recomputation of static corrections to a datum nearer the land surface; (3) intensive velocity analyses; and (4) near-trace muting analyses. The number, resolution, and lateral continuity of shallow reflections were greatly enhanced on the reprocessed sections, as was the delineation of shallow, major faults. Reflections on a synthetic seismogram, created from a borehole drilled to a depth of 786 m on seismic line IQS-11, matched precisely with shallow reflections on the reprocessed section. The 33 reprocessed sections were instrumental in preparing a map showing the major structural features that affect the shallow aquifer system. Analysis of the map provides a better understanding of the effect of these shallow features on the regional occurrence, movement, and quality of groundwater in the concession area. Results from this study demonstrate that original seismic field tapes collected for deep petroleum exploration can be reprocessed to explore for groundwater.

Journal of Applied Geophysics↗
USGS1996

Postaudit of head and transmissivity estimates and ground-water flow models of Avra Valley, Arizona

Ground water from regional alluvial-aquifer systems is the main source of water in the alluvial basins of Arizona, such as Avra Valley. Ground-water flow models are used to assess ground-water availability and the effects of development on the regional ground-water resources. A postaudit of regional-head and transmissivity estimates and the ground-water flow models of Avra Valley was used to evaluate potential errors in the distribution of aquifer properties and recharge that can cause predictive errors in ground-water models. Simulations of predevelopment conditions in 1940 and historical development conditions for 1960-79 provided the basis of comparison for assessing predictive errors of historical conditions for two regional ground-water flow models. Potential errors in the estimation of the regional-head and transmissivity and alternate conceptual models were compared with an existing calibrated two-layer flow model for predevelopment (1940) and developed conditions (1940-85). Measured heads can be subdivided into a north-central region and a region south of the basin constriction. A more variable regional-head surface typical of developed aquifer systems was indicated by kriged developed heads (1985) with about 50 percent more uncertainty than predevelopment heads (1940). Incorporating heads from adjacent basins at the ground-water inflow and outflow regions reduced uncertainty in kriged heads for these boundary areas. Universal cokriging of heads with the strongly correlated land-surface altitudes may improve regional-head estimates and model comparisons where head data are sparse. Local transmissivity estimates can be subdivided into northern and south-central regions that are distributed along the valley axis and the Santa Cruz River. Regional geostatistical estimates of transmissivity, which are based solely on local estimates, are low in the northern part of Avra Valley and are high in the south-central part when compared with the head-conditioned model-derived estimates. These differences may be related to a systematic bias between aquifer-test conditions and methods of aquifer-test analysis. Cokriging transmissivities with specific capacity and silt-and-clay content provided the least uncertainty of all kriged estimates. Predictive errors for the Avra Valley model are the result of a different combination of factors that become significant in the simulation of ground-water flow for the periods representing predevelopment, historical development, and future development conditions. Predictive errors for simulation of predevelopment conditions are caused by potential systematic errors in estimates of local transmissivity, uncertainty in long-term mountain-front recharge, and uncertainty in predevelopment heads along the margins of the basin where recharge and transmissivity estimates are constrained by heads during model calibration. Analog-model historical predictions of future development indicate changes to 1985 were as much as 50 to 100 feet different from actual declines that were caused by errors in the spatial distribution and not the total amount of estimated future pumpage. Predictive errors for simulation of historical development (1960-79) appear to be caused to a greater extent by combined errors in estimates of transmissivity and storage properties and to a lesser extent by estimates of net withdrawal and subsidence. Comparison of the two digital models resulted in differences in transmissivity of as much as 30,000 feet squared per day and differences in specific yield of as much as 0.1. In combination with some differences in net withdrawal, these model-parameter differences resulted in local differences in change in storage of as much as 4,000 acre-feet per square mile and are equivalent to historical predictive errors in water levels of as much as 40 feet. Areas with no differences in model parameters yield comparable simulated water-level declines that are similar to measured declines. The pattern of differences in transmissivity and storage parameters are similar to differences between model-derived estimates conditioned on heads and related geostatistical estimates derived from aquifer-test estimates. A postaudit analysis of alternate conceptual models was explored on the basis of well-by-well comparisons of reductions in mean error and variance, and through the use of standardized calibration-error maps for predevelopment heads (1940) and developed heads (1985). Calibration-error maps provide a useful tool for exploring the spatial structure of model errors and the relative adequacy of model fit that is not available from traditional methods of model comparison. Calibration-error maps indicate estimated heads were too high in the southern part of Avra Valley, and estimated heads were too low in the northern part. Increased transmissivity in the southern part of the lower model layer; decreased hydraulic conductivity in the southwestern part of the upper layer; reduced ground-water inflow from Altar Valley; and increased recharge along the Tortolita Mountains, Tucson Mountains, and Brawley Wash yielded a significantly better model for predevelopment but not for developed conditions (1940-85). This may indicate that alternate conceptual models are different for different time periods or require analysis of time-varying model parameters for developed conditions, such as climatically variable recharge. Predictive errors for future simulations (1986-2025) also could potentially include errors of more than 40 ft from omission of subsidence from the simulation of regional ground-water flow in Avra Valley. Further refinement of the changing conceptual model of an aquifer system under continuing development and variable climate, such as Avra Valley, will require a variety of additional geophysical, geochemical, and hydraulic field data.

Arizona↗
USGS2009

Magnetotelluric and audiomagnetotelluric groundwater survey along the Humu'ula portion of Saddle Road near and around the Pohakuloa Training Area, Hawaii

The Pohakuloa Training Area (PTA), operated by the U.S. Army on the Big Island of Hawaii, is in need of a reliable potable water supply to sustain ongoing operations by staff and trainees. In an effort to acquire baseline hydrologic data with which to develop a plan for providing that water, a series of magnetotelluric (MT) geophysical surveys was performed that spanned the Mauna Loa/Mauna Kea Saddle region of Hawaii Island. These surveys provided electrical resistivity profiles and resistivity maps at several elevations along the axis of the field measurements that can be interpreted to yield information on the depth to the water table. In 2004 a preliminary sequence of 23 audiomagnetotelluric (AMT) soundings was collected along Saddle Road extending from the Waikii Ranch area, west of the PTA, to Department of Hawaiian Home Lands Humu'ula properties east of the Mauna Kea access road. The results of those soundings showed that highly resistive rocks, consistent with dry basalts, were present to depths of at least one kilometer, the maximum depth to which the AMT technique can reliably reach in Hawaii's rocks. A second survey was conducted in 2008 using MT instruments capable of recovering resistivity data to depths of several kilometers below sea level where saturated formations are known to exist. A total of 30 MT soundings was performed along a roughly east to west transect that extended from the (recently acquired) Keamuku PTA lands on the west to as far as the County of Hawaii's upper Kaumana water supply well to the east. Inversion and processing of the field data yielded an electrical cross-section following the Saddle that roughly parallels the geologic contact between the Mauna Kea and Mauna Loa lavas. Several additional electrical sections were constructed normal to the main transect to investigate the three-dimensional nature of the contact. These resistivity data and models suggest that the elevation of saturated rock in places are 400 to 600 meters above mean sea level beneath the surveyed region. Highest elevations for water-saturated zones based upon preferred electrical models are located between training area 3 and training area 6 southwest of training area 4.

Hawai'i↗
USGS2017

Spatial heterogeneity of within-stream methane concentrations

Streams, rivers, and other freshwater features may be significant sources of CH 4 to the atmosphere. However, high spatial and temporal variabilities hinder our ability to understand the underlying processes of CH 4 production and delivery to streams and also challenge the use of scaling approaches across large areas. We studied a stream having high geomorphic variability to assess the underlying scale of CH 4 spatial variability and to examine whether the physical structure of a stream can explain the variation in surface CH 4 . A combination of high-resolution CH 4 mapping, a survey of groundwater CH 4 concentrations, quantitative analysis of methanogen DNA, and sediment CH 4 production potentials illustrates the spatial and geomorphic controls on CH 4 emissions to the atmosphere. We observed significant spatial clustering with high CH 4 concentrations in organic-rich stream reaches and lake transitions. These sites were also enriched in the methane-producing mcrA gene and had highest CH 4 production rates in the laboratory. In contrast, mineral-rich reaches had significantly lower concentrations and had lesser abundances of mcrA . Strong relationships between CH 4 and the physical structure of this aquatic system, along with high spatial variability, suggest that future investigations will benefit from viewing streams as landscapes, as opposed to ecosystems simply embedded in larger terrestrial mosaics. In light of such high spatial variability, we recommend that future workers evaluate stream networks first by using similar spatial tools in order to build effective sampling programs.

Journal of Geophysical Research G: Biogeosciences↗
USGS2022

Large surface-rupture gaps and low surface fault slip of the 2021 Mw 7.4 Maduo earthquake along a low-activity strike-slip fault, Tibetan Plateau

Based on field investigations, interpretations of high-resolution UAV images, and analyses of available InSAR data, we mapped the fault geometry and surface ruptures of the 2021 M w 7.4 Maduo earthquake that occurred on a low-activity strike-slip fault within the Tibetan Plateau. The results indicate that (a) the earthquake activated a fault that is ∼161 km long and has complicated structural geometry; (b) the surface rupture occurs over a distance of 148 km, but is separated into three distinct segments by two large gaps (38 and 20 km, respectively); (c) within the surface-rupture segments, the horizontal and vertical displacements are typically 0.2–2.6 m (much lower than the InSAR-based slip maximum of 2–6 m at depth) and ≤0.4 m, respectively. The two large gaps of the Maduo surface rupture represent the two largest surface-rupture discontinuities of strike-slip earthquakes ever documented, and coincide with structurally complicated fault portions and near-surface soft sediments.

Tibetan Plateau↗
USGS2006

Hydrogeologic setting and ground water flow beneath a section of Indian River Bay, Delaware

The small bays along the Atlantic coast of the Delmarva Peninsula (Delaware, Maryland, and Virginia) are a valuable natural resource, and an asset for commerce and recreation. These coastal bays also are vulnerable to eutrophication from the input of excess nutrients derived from agriculture and other human activities in the watersheds. Ground water discharge may be an appreciable source of fresh water and a transport pathway for nutrients entering the bays. This paper presents results from an investigation of the physical properties of the surficial aquifer and the processes associated with ground water flow beneath Indian River Bay, Delaware. A key aspect of the project was the deployment of a new technology, streaming horizontal resistivity, to map the subsurface distribution of fresh and saline ground water beneath the bay. The resistivity profiles showed complex patterns of ground water flow, modes of mixing, and submarine ground water discharge. Cores, gamma and electromagnetic-induction logs, and in situ ground water samples collected during a coring operation in Indian River Bay verified the interpretation of the resistivity profiles. The shore-parallel resistivity lines show subsurface zones of fresh ground water alternating with zones dominated by the flow of salt water from the estuary down into the aquifer. Advective flow produces plumes of fresh ground water 400 to 600 m wide and 20 m thick that may extend more than 1 km beneath the estuary. Zones of dispersive mixing between fresh and saline ground water develop on the upper, lower, and lateral boundaries of the the plume. the plumes generally underlie small incised valleys that can be traced landward to stream draining the upland. The incised valleys are filled with 1 to 2 m of silt and peat that act as a semiconfining layer to restrict the downward flow of salt water from the estuary. Active circulation of both the fresh and saline ground water masses beneath the bay is inferred from the geophysical results and supported by geochemical data.

Delaware↗
USGS2001

Composition and Distribution of Streambed Sediments in the Penobscot River, Maine, May 1999

Sediment samples were collected and geophysical surveys were run along 50 miles of the Penobscot River, Maine, in the spring of 1999 to produce maps that describe the composition and distribution of streambed sediments for selected areas in the river channel. The objective of the sediment survey was to locate areas along the river where fine-grained, easily transportable sediment types were deposited between Old Town and Medway, Maine. These data can be used to design future sediment-sampling programs to assess the quality of streambed sediments and evaluate the health of the Penobscot River. This report describes the results of the sediment survey and the methods used to collect, analyze, and interpret the data used to create maps of streambed-sediment types in the study area. Deposits of fine-grained sediments (mud and sand) are scattered along the shorelines of the mainland and the islands and at the downstream ends of islands and at the mouths of brooks and streams. The most extensive depositional areas were found in the Mattaseunk Dam impoundment near Medway. The main areas of the river channel consist primarily of gravel, sand, and rock.

Water-Resources Investigations Report↗
USGS2006

A field guide to the central, creeping section of the San Andreas fault and the San Andreas Fault Observatory at Depth

This field trip is along the central section of the San Andreas fault and consists of eight stops that illustrate surface evidence of faulting, in general, and features associated with active fault creep, in particular. Fault creep is slippage along a fault that occurs either in association with small-magnitude earthquakes or without any associated large-magnitude earthquakes. Another aspect of the trip is to highlight where there are multiple fault traces along this section of the San Andreas fault zone in order to gain a better understanding of plate-boundary processes. The first stop is along the Calaveras fault, part of the San Andreas fault system, at a location where evidence of active fault creep is abundant and readily accessible. The stops that follow are along the San Andreas fault and at convenient locations to present and discuss rock types juxtaposed across the fault that have been transported tens to hundreds of kilometers by right-lateral motion along the San Andreas fault. Stops 6 and 7 are examples of recent studies of different aspects of the fault: drilling into the fault at the depth of repeating magnitude (M) 2 earthquakes with the San Andreas Fault Observatory at Depth (SAFOD) and the geological, geophysical, and seismological study of M 6 earthquakes near the town of Parkfield. Along with the eight official stops on this field trip are 12 “rolling stops”—sites of geologic interest that add to the understanding of features and processes in the creeping section of the fault. Many of the rolling stops are located where stopping is difficult to dangerous; some of these sites are not appropriate for large vehicles (buses) or groups; some sites are not appropriate for people at all. We include photographs of or from many of these sites to add to the reader's experience without adding too many stops or hazards to the trip. An extensive set of literature is available for those interested in the San Andreas fault or in the creeping section, in particular. For more scientifically oriented overviews of the fault, see Wallace ( 1990 ) and Irwin ( 1990 ); for a more generalized overview with abundant, colorful illustrations, see Collier ( 1999 ). Although the presence of small sections of the San Andreas fault was known before the great 1906 San Francisco earthquake, it was only after that event and subsequent geologic investigations reported in Lawson ( 1908 ) that showed the fault as a long structure, extending all the way from east of Los Angeles into northern California. Prentice ( 1999 ) described the importance of the 1908 “Lawson report” and how it pivotally influenced the understanding of the San Andreas. Hill ( 1981 ) presented a wonderful introduction to the evolution of thought on the San Andreas. Geologic maps and maps of the most recently active fault trace in the creeping section, or large parts of it, include those by Brown ( 1970 ), Dibblee ( 1971 , 1980 ), and Wagner et al. ( 2002 ); detailed geologic maps are discussed at various stops in this guide. Various aspects of the creeping section of the San Andreas fault have been the focus of many geologic field trips in the past few decades. Guidebooks for some of those trips include those by Gribi ( 1963a , 1963b ), Brabb et al. ( 1966 ), Rogers ( 1969 ), Bucknam and Haller ( 1989 ), Harden et al. ( 2001 ), and Stoffer ( 2005 ). The creeping section of the San Andreas fault zone lies between areas that experienced large-displacement surface breakage during great earthquakes in 1857 and 1906 (Fig. 1 inset). Burford and Harsh ( 1980 ) divided the creeping section into three segments: (1) a northwest section where the creep rate increases to the southeast in step-like increments, (2) a central section where the creep rate is relatively constant at a maximum value of ∼30 mm/yr (∼1.2 in/yr), and (3) a southeast section where the creep rate decreases to the southeast (Fig. 2 ). The rate of slip along the creeping section of the fault zone has been measured using creepmeters, alignment arrays, and laser distance-measuring devices. The aperture of measurements over which these measurements are made ranges from 10 m (∼33 ft) (creepmeters) to 100 m (∼330 ft) (alignment arrays) to kilometers and tens of kilometers (laser measuring devices). Creepmeter and alignment-array measurements are here termed “near-fault” measurements; laser measurements over distances of 1–2 km (∼0.6–1.2 mi) are termed “intermediate-scale” measurements; laser measurements over tens of kilometers (miles) are termed “broadscale” measurements. Comparisons among near-fault, intermediate-scale, and broadscale measurements and geologic maps show that the northwest part of the creeping section of the fault is composed of two narrow zones of active deformation, one along the San Andreas fault and one along the Calaveras-Paicines fault, whereas the central and southeast sections are both composed of a single relatively narrow zone of deformation. The southeast section is transitional to a locked zone southeast of Cholame; a locked fault is one that slips only in association with a moderate to large earthquake. Throughout the creeping section of the San Andreas fault zone, broadscale measurements generally indicate more deformation than near-fault and intermediate-scale measurements, which are in reasonably close agreement except at Monarch Peak (Mustang Ridge), near the center of the creeping section and our Stop 5 ((Figs. 1 ) and 2 ). Features that we see on this trip include offset street curbs, closed depressions (sag ponds), fault scarps (steep slopes formed by movement along a fault), a split and displaced tree, offset fence lines, fresh fractures, and offset road lines (Fig. 3 is a sketch showing some of the landforms that represent deformation by an active fault). We also see evidence of long-term maturity of the San Andreas fault, as indicated by fault features and displaced rock types (Fig. 4 ). Finally, we will visit sites of ongoing research into the processes associated with earthquakes and their effects. Discussions include drilling into the San Andreas fault at the SAFOD drill site and the 2004 Parkfield earthquake and its effects and implications.

California↗
USGS2019

Map of the approximate inland extent of saltwater at the base of the Biscayne aquifer in Miami-Dade County, Florida, 2018

The inland extent of saltwater at the base of the Biscayne aquifer in eastern Miami-Dade County, Florida, was mapped in 2011, and it was mapped in the Model Land Area in 2016. The saltwater interface has continued to move inland in some areas and is now near several active well fields. An updated approximation of the inland extent of saltwater has been created by using data collected during March 8–December 13, 2018, from 111 monitoring wells open to the Biscayne aquifer near its base. Chloride concentrations in water samples from the monitoring wells and bulk conductivity from geophysical logs and measurements of the specific conductance of groundwater were used to approximate the position of the isochlor representing a chloride concentration of 1,000 milligrams per liter (mg/L) at the base of the Biscayne aquifer. An average rate of saltwater interface movement of about 102 meters per year in the Model Land Area along SW 360 Street was estimated from the approximated dates of arrival of the 250-, 500-, and 1,000-mg/L isochlors at wells TPGW-7L (2013–2014) and ACI-MW-05-FS (2017–2018). This estimate assumes that the interface is traveling in a path parallel to an imaginary line connecting the two monitoring wells. Of the 111 wells from which data were used, 80 wells have open intervals of ≤ 4 meters, 20 of the wells have open intervals that range from 4.3 to 39.6 meters, and the lengths of the open intervals could not be determined in 11 wells. Studies have shown that long open intervals might allow water from various depths to mix under ambient or pumped conditions, which in turn could alter the maximum chloride concentration sampled in the well, or it might change the depth at which the maximum specific conductance is measured within a well, relative to its depth in the aquifer. The approximation of the inland extent of the saltwater interface and the estimated rate of movement of the interface are dependent on the quality of existing data. Improved estimates could be obtained by installing uniformly designed monitoring wells in systematic transects extending landward of the advancing saltwater interface. To achieve this goal, Miami-Dade County and some other organizations are routinely adding new monitoring wells with short open intervals and replacing poorly designed or positioned monitoring wells to improve spatial coverage of the network.

Florida↗
USGS2009

Uncertainty analysis for seismic hazard in Northern and Central Italy

In this study we examine uncertainty and parametric sensitivity of Peak Ground Acceleration (PGA) and 1-Hz Spectral Acceleration (1-Hz SA) in probabilistic seismic hazard maps (10% probability of exceedance in 50 years) of Northern and Central Italy. The uncertainty in hazard is estimated using a Monte Carlo approach to randomly sample a logic tree that has three input-variables branch points representing alternative values for b-value, maximum magnitude (Mmax) and attenuation relationships. Uncertainty is expressed in terms of 95% confidence band and Coefficient Of Variation (COV). The overall variability of ground motions and their sensitivity to each parameter of the logic tree are investigated. The largest values of the overall 95% confidence band are around 0.15 g for PGA in the Friuli and Northern Apennines regions and around 0.35 g for 1-Hz SA in the Central Apennines. The sensitivity analysis shows that the largest contributor to seismic hazard variability is uncertainty in the choice of ground-motion attenuation relationships, especially in the Friuli Region (???0.10 g) for PGA and in the Friuli and Central Apennines regions (???0.15 g) for 1-Hz SA. This is followed by the variability of the b-value: its main contribution is evident in the Friuli and Central Apennines regions for both 1-Hz SA (???0.15 g) and PGA (???0.10 g). We observe that the contribution of Mmax to seismic hazard variability is negligible, at least for 10% exceedance in 50-years hazard. The overall COV map for PGA shows that the uncertainty in the hazard is larger in the Friuli and Northern Apennine regions, around 20-30%, than the Central Apennines and Northwestern Italy, around 10-20%. The overall uncertainty is larger for the 1-Hz SA map and reaches 50-60% in the Central Apennines and Western Alps.

Annals of Geophysics↗
USGS2017

Stratigraphic cross sections of the Niobrara interval of the Cody Shale and associated rocks in the Wind River Basin, central Wyoming

The Wind River Basin in Wyoming is one of many structural and sedimentary basins that formed in the Rocky Mountain foreland during the Laramide orogeny. The basin is nearly 200 miles long, 70 miles wide, and encompasses about 7,400 square miles in central Wyoming. The basin is bounded by the Washakie Range, Owl Creek uplift, and southern Bighorn Mountains on the north, the Casper arch on the east, the Granite Mountains on the south, and Wind River Range on the west. Many important conventional oil and gas fields producing from reservoirs ranging in age from Mississippian through Tertiary have been discovered in this basin. In addition, an extensive unconventional overpressured basin-centered gas accumulation has been identified in Cretaceous and Tertiary strata in the deeper parts of the basin. It has long been suggested that various Upper Cretaceous marine shales, including the Cody Shale, are the principal hydrocarbon source rocks for many of these accumulations. With recent advances and success in horizontal drilling and multistage fracture stimulation, there has been an increase in exploration and completion of wells in these marine shales in other Rocky Mountain Laramide basins that were traditionally thought of only as hydrocarbon source rocks. The two stratigraphic cross sections presented in this report were constructed as part of a project carried out by the U.S. Geological Survey to characterize and evaluate the undiscovered continuous (unconventional) oil and gas resources of the Niobrara interval of the Upper Cretaceous Cody Shale in the Wind River Basin in central Wyoming. The primary purpose of the cross sections is to show the stratigraphic relationship of the Niobrara equivalent strata and associated rocks in the lower part of the Cody Shale in the Wind River Basin. These two cross sections were constructed using borehole geophysical logs from 37 wells drilled for oil and gas exploration and production, and one surface section along East Sheep Creek near Shotgun Butte in the northwestern part of the basin. Both lines originate at the East Sheep Creek surface section and end near Clarkson Hill in the extreme southeastern part of the basin. The stratigraphic interval extends from the upper part of the Frontier Formation to the middle part of the Cody Shale. The datum is the base of the “chalk kick” marker bed, a distinctive resistivity peak or zone in the lower part of the Cody Shale. A gamma ray and (or) spontaneous potential (SP) log was used in combination with a resistivity log to identify and correlate units. Marine molluscan index fossils collected from nearby outcrop sections were projected into the subsurface to help determine the relative ages of the strata and aid in correlation.

Wyoming↗
USGS1967

Effects of the earthquake of March 27, 1964, at Seward, Alaska

Seward, in south-central Alaska, was one of the towns most devastated by the Alaska earthquake of March 27, 1964. The greater part of Seward is built on an alluvial fan-delta near the head of Resurrection Bay on the southeast coast of the Kenai Peninsula. It is one of the few ports in south-central Alaska that is ice free all year, and the town’s economy is almost entirely dependent upon its port facilities. The Alaska earthquake of March 27, 1964, magnitude approximately 8.3–8.4, began at 6:36 p.m. Its epicenter was in the northern part of the Prince William Sound area; focal depth was 20–50 km. Strong ground motion at Seward lasted 3–4 minutes. During the shaking, a strip of land 50–400 feet wide along the Seward waterfront, together with docks and other harbor facilities, slid into Resurrection Bay as a result of large-scale submarine landsliding. Fractures ruptured the ground for'severa1 hundred feet back from the landslide scarps. Additional ground was fractured in the Forest Acres subdivision and on the alluvial floor of the Resurrection River valley; fountaining and sand boils accompanied the ground fracturing. Slide-generated wares, possibly seiche waves, and seismic sea waves crashed onto shore; ware runup was as much as 30 feet above mean lower low water and caused tremendous damage; fire from burning oil tanks added to the destruction. Damage from strong ground motion itself was comparatively minor. Tectonic subsidence of about 3.6 feet resulted in low areas being inundated at high tide. Thirteen people were killed and five were injured as a result of the earthquake. Eighty-six houses were totally destroyed and 260 were heavily damaged. The harbor facilities were almost completely destroyed, and the entire economic base of the town was wiped out. The total cost to replace the destroyed public and private facilities was estimated at $22 million. Seward lies on the axis of the Chugach Mountains geosyncline. The main structural trend in the mapped area, where the rocks consist almost entirely of graywacke and phyllite, is from near north to N. 20° E. Beds and cleavage of the rocks commonly dip 70° W. or NW. to near vertical. Locally, the rocks are complexly folded or contorted. So major faults were found in the mapped area, but small faults, shear zones, and joints are common. Surficial deposits of the area hare been divided for mapping into the following units: drift deposits, alluvial fan deposits, valley alluvium, intertidal deposits, landslide deposits, and artificial fill. Most of these units intergrade and were deposited more or less contemporaneously. The drift deposits consist chiefly of till that forms moraines along the lower flanks of the Resurrection River valley and up tributary valleys. The till is predominantly silt and sand and lesser amounts of clay-size particles, gravel, cobbles, and boulders. Glacial outwash and stratified ice-contact deposits constitute the remainder of the drift deposits. Fans and fan-deltas have been deposited at the valley mouths of tributary streams. Some, including the one upon which Seward built, project into Resurrection Bay, and deltaic-type deposits form their distal edges. The larger fans—composed chiefly of loosely compacted and poorly sorted silt, sand, and gravel—form broad aprons having low gradients. The fan deposits range in thickness from about 100 feet to possibly several hundred feet and, at least in some places, lie on a platform of compact drift. Smaller fans at the mouths of several canyons have steep gradients and considerable local relief. Valley alluvium, deposited chiefly by the Resurrection River, consists mostly of coarse sand and fine to medium gravel. In the axial part of the valley it is probably more than 100 feet thick. Near the head of Resurrection Bay, the alluvium is underlain by at least 75 feet of marine deltaic sediments, which are in turn underlain by 600 or more feet of drift in the deepest part of the bedrock valley. Beach, deltaic, and estuarine sediments, deposited on intertidal flats at the head of the bay and along far1 margins that extend into the bay, arc mapped as intertidal deposits. They consist mostly of silt, sand, and fine gravel, and lesser amounts of clay-size particles. The earthquake reactivated old slides and trigged new ones in the mountains. Rock and snow avalanches, debris flows, and creep of talus deposits characterized slide activity on the steeper slops. The Seward waterfront had been extended before the earthquake by adding artificial fill consisting of loose sand and gravel; part of the lagoon area had been filled with refuse. After the earth- quake, fill, consisting of silt and sand dredged from the head of the bay, was pumped onto part of the lagoon area and also on land at the northwest corner of the bay. Response to the disaster was immediate and decisive. City, State, and Federal agencies, as well as other organizations and individuals, gave unstintingly of their time and facilities. Within a few days, there was temporary restoration of water, sewerage, and electrical facilities. The U.S. Army Corps of Engineers was authorized to select sites and construct a new dock for the Alaska Railroad, a new small-boat basin, and related facilities. The firm of Shannon and Wilson, Inc., under contract to the Corps of Engineers, investigated subsurface soils extensively to determine the factors responsible for the sliding along the Seward waterfront and to assist in site selection for reconstruction of the destroyed harbor facilities. Borings also made along the Seward waterfront and at the head of the bay, and laboratory tests were conducted on pertinent samples. These studies were augmented by geophysical studies both on land and in the bay. In addition, the Corps of Engineers made shallow borings on the intertidal flats at the head of the bay and performed pile-driving and load tests. Borings also were drilled and test pits were dug in the subdivision of Forest Acres. Sliding along the Seward waterfront markedly deepened the water along the former shoreline. Post-earthquake slopes of the bay floor immediately offshore also are steeper in places than before the earthquake. The strong ground motion of the earthquake triggered the landsliding, but several factors may have contributed to the magnitude and characteristics of the slides. These factors are: (1) the long duration of strong ground motion, (2) the grain size and texture of the material involved in the sliding, (3) the probability that the finer grained materials liquefied and flowed seaward, and (4) the added load of manmade facilities built on the edge of the shore, Secondary effects of the slides themselves—sudden drawdown of water, followed by the weight of returning waves—also may have contributed to the destruction. Submarine sliding at the northwest corner of the bay occurred in fine-grained deltaic deposits whose frontal slopes probably were in metastable equilibrium under static conditions. Uplift pressures from aquifers under hydrostatic head, combined with the probable liquefaction characteristics of the sediments when vibrated by strong ground motion, probably caused the material to slide and flow seaward as a heavy slurry. Under static conditions, no major shoreline or submarine landsliding is expected in the Seward area; in the event of another severe earthquake, however, additional sliding is likely along the Seward waterfront and also in the deltaic deposits at the northwest corner of the bay. Fractured ground in back of the present shoreline along the Seward waterfront is an area of incipient landslides that would be unstable under strong shaking. For this reason the Scientific and Engineering Task Force placed the area in a high-risk classification and recommended no repair, rehabilitation, or new construction in this area involving use of Federal funds; it was further recommended that the area should be reserved for park or other uses that do not involve large congregations of people. The deltaic deposits at the head of the bay probably also would be susceptible to sliding during another large earthquake. This sliding would result in further landward retreat of the present shoreline toward the new railroad dock. Specifications for the new dock, whose seaward end is now approximately 1,100 feet from the back scarp of the subaqueous landslide, require design pro- visions to withstand seismic shock up to certain limits. Earthquake-induced fracturing of the ground in the subdivision of Forest Acres was confined to the lower part of a broad alluvial fan. There, sewer and water lines were ruptured and the foundations of some homes were heavily damaged. Landsliding, such as occurred along the shoreline of the bay, was not a contributing cause of the fracturing. Two hypotheses are offered to explain the fracturing: 1. Seismic energy was transformed into visible surface waves of such amplitude that the strength of surface layer was exceeded and rupturing occurred; tensional and compressional stresses alternately opened and closed the fractures and forced out water and mud. 2. Compaction by vibration of the fine-grained deposits of the fan caused ground settlement and fracturing; ground water under temporary hydrostatic head was forced to the surface as fountains and carried the finer material with it. Water waves that crashed onto shore, while shaking was still continuing, were generated chiefly by onshore and offshore landsliding. Waves that overran the shores about 25 minutes after shaking stopped and that continued to arrive for the next several hours are believed to be seismic sea waves (tsunamis) that originated in an uplifted area in the Gulf of Alaska. During the time of seismic sea-wave activity and perhaps preceding it, seiche wares also may have been generated within Resurrection Bay and complicated the wave effects along the shoreline.

Alaska↗
USGS2012

Tracking lava flow emplacement on the east rift zone of Kilauea, Hawai’i with synthetic aperture radar (SAR) coherence

Lava flow mapping is both an essential component of volcano monitoring and a valuable tool for investigating lava flow behavior. Although maps are traditionally created through field surveys, remote sensing allows an extraordinary view of active lava flows while avoiding the difficulties of mapping on location. Synthetic aperture radar (SAR) imagery, in particular, can detect changes in a flow field by comparing two images collected at different times with SAR coherence. New lava flows radically alter the scattering properties of the surface, making the radar signal decorrelated in SAR coherence images. We describe a new technique, SAR Coherence Mapping (SCM), to map lava flows automatically from coherence images independent of look angle or satellite path. We use this approach to map lava flow emplacement during the Pu‘u ‘Ō‘ō-Kupaianaha eruption at Kīlauea, Hawai‘i. The resulting flow maps correspond well with field mapping and better resolve the internal structure of surface flows, as well as the locations of active flow paths. However, the SCM technique is only moderately successful at mapping flows that enter vegetation, which is also often decorrelated between successive SAR images. Along with measurements of planform morphology, we are able to show that the length of time a flow stays decorrelated after initial emplacement is linearly related to the flow thickness. Finally, we use interferograms obtained after flow surfaces become correlated to show that persistent decorrelation is caused by post-emplacement flow subsidence.

Hawai'i↗
USGS2016

Compilation of V S 30 Data for the United States

V S 30 , the time-averaged shear-wave velocity ( V S ) to a depth of 30 meters, is a key index adopted by the earthquake engineering community to account for seismic site conditions. V S 30 is typically based on geophysical measurements of V S derived from invasive and noninvasive techniques at sites of interest. Owing to cost considerations, as well as logistical and environmental concerns, V S 30 data are sparse or not readily available for most areas. Where data are available, V S 30 values are often assembled in assorted formats that are accessible from disparate and (or) impermanent Web sites. To help remedy this situation, we compiled V S 30 measurements obtained by studies funded by the U.S. Geological Survey (USGS) and other governmental agencies. Thus far, we have compiled V S 30 values for 2,997 sites in the United States, along with metadata for each measurement from government-sponsored reports, Web sites, and scientific and engineering journals. Most of the data in our V S 30 compilation originated from publications directly reporting the work of field investigators. A small subset (less than 20 percent) of V S 30 values was previously compiled by the USGS and other research institutions. Whenever possible, V S 30 originating from these earlier compilations were crosschecked against published reports. Both downhole and surface-based V S 30 estimates are represented in our V S 30 compilation. Most of the V S 30 data are for sites in the western contiguous United States (2,141 sites), whereas 786 V S 30 values are for sites in the Central and Eastern United States; 70 values are for sites in other parts of the United States, including Alaska (15 sites), Hawaii (30 sites), and Puerto Rico (25 sites). An interactive map is hosted on the primary USGS Web site for accessing V S 30 data ( https://earthquake.usgs.gov/data/vs30/us/ ).

Data Series↗
USGS2020

High-resolution airborne geophysical survey of the Shellmound, Mississippi area

In late February to early March 2018, the U.S. Geological Survey acquired 2,364 line-kilometers (km) of airborne electromagnetic, magnetic, and radiometric data in the Shellmound, Mississippi study area. The purpose of this survey is to contribute high-resolution information about subsurface geologic structure to inform groundwater models, water resource infrastructure studies, and local decision making. The Shellmound region hosts a managed aquifer recharge (MAR) pilot project, developed by the Agricultural Research Service of the U.S. Department of Agriculture. The MAR pilot project is investigating the use of bank filtration along the Tallahatchie River as a source for recharge in areas of significant groundwater decline. Direct injection into the Mississippi River Valley Alluvial aquifer (MRVA) occurs about 3 km from the extraction gallery. Understanding the structure of the aquifer, including both shallow and deep confining units, is important for the success of this pilot MAR study and may be even more important for potential future large-scale MAR projects and groundwater model development efforts.

Mississippi↗
USGS1958

Geology and ore deposits of the Monument Valley area, Apache and Navajo counties, Arizona: Part II

In 1951 and 1952, the U.S. Geological Survey conducted a program of uranium investigations and geologic mapping in the Monument Valley area, Apache and Navajo Counties, Ariz. About 700 square miles were mapped on the Navajo Indian Reservation. A resource appraisal of the area was an inherent part of the program, and is detailed in this report. Production of vanadium and uranium is from two areas, the Monument No. 1 mine area in Navajo County, and the Monument No. 2 mine area in Apache County. In the period 1942-53 about 200,300 tons of ore was produced from these two areas. This ore yielded about 1,700,000 pounds of U 3 O 8 and about 6,500,000 pounds of V 2 O 5 . The grade ranged from 0.15 percent U 3 O 8 to 0.60 percent U 3 O 8 , and from 0.38 percent V 2 O 5 to 3.02 percent V 2 O 5 . The vanadium-uranium ratio is about 4:1. The ore deposits are composed principally of the hydrous calcium-uranium vanadate tyuyamunite in basal channel sediments of the Shinarump member off the Chinle formation. Four types of ore bodies are present: (1) rods, (2) tabular ore bodies, (3) corvusite-type ore bodies, and (4) rolls. The reserves of uranium- and vanadium-bearing material are classed as measured, indicated, inferred, and potential. The reserves are further divided into three grade classes for material 1 foot or more thick: (1) 0.10 percent U 3 O 8 and 1.00 percent V 2 O 5 and above; (2) 0.05 percent U 3 O 8 and 0.50 percent V 2 O 5 and less than 0.10 percent U 3 O 8 and 1.00 percent V 2 O 5 ; and (3) 0.01 percent U 3 O 8 and 0.10 percent V 2 O 5 and less than 0.05 percent U 3 O 8 and 0.05 percent V 2 O 5 . Measured reserves as of June 1953, in the Monument Valley area, Arizona, (all in the Monument No. 2 mine) total about 36,000 tons. Indicated reserves in the first grade class amount to about 62,000 tons. In this same grade class inferred reserves total about 3,000,000 tons. In the second grade class indicated and inferred reserves amount to about 2,000,000 tons. Inferred reserves in the third grade class total about 345,000 tons of mineralized material. Potential reserves in all grade classes for the Monument Valley area amount to about 13,000,000 tons. It is recommended that an extensive exploration program be carried out in the Monument Valley area, Arizona. This program would consist of two phases. The first phase would involve a geophysical survey of selected channels and would have at its principal objective the delineation of the trend, length, width, and depth of scour of the channels. The second phase would consist of a diamond-drilling program that would make use of the data secured by the geophysical survey. This drilling program would have as one of its principal objectives the determination of which channels are most likely to contain ore bodies. Once the favorable channels are discovered, the drilling program could be carried on most suitably by private operators.

Arizona↗
USGS2000

Detection of conduit-controlled ground-water flow in northwestern Puerto Rico using aerial photograph interpretation and geophysical methods

The development potential of ground-water resources in the karst limestone of northwestern Puerto Rico, in an area extending from the Río Camuy to Aguadilla, is uncertain as a result of limited knowledge of the location of areas where a high density of cavities (interconnected fractures, conduits, and other dissolution features) might suggest the occurrence of high water yields. The presence in northwestern Puerto Rico of numerous coastal submarine springs, cavernous porosity in some of the wells, and rivers with entrenched and underground paths, indicate that it is probable that water-bearing, subterranean interconnected cavities occur in the area between the Río Camuy and Aguadilla. The number of exploratory wells needed to determine the location of these conduits or zones of enhanced secondary porosity could be substantially reduced if more information were available about the location of these subterranean features, greatly reducing the drilling costs associated with a trial-and-error exploratory process. A 3-year study was conducted by the U.S. Geological Survey, in cooperation with the Puerto Rico Aqueduct and Sewer Authority, to detect the presence of cavities that might suggest the occurrence of conduit-controlled groundwater flow. Aerial photographs, geologic and topographic maps, and field reconnaissance were used to identify such linear terrain features as ridges, entrenched canyons, and fracture traces. Natural potential and gravity geophysical methods were also used. The following sites were selected for the aerial photograph interpretation and geophysical testing: Caimital Bajo uplands and former Ramey Air Force Base in Aguadilla; Quebrada de los Cedros between Aguadilla and Isabela; the University of Puerto Rico Agricultural Experiment Station, Otilio dairy farm, and Pozo Brujo in Isabela; the Monte Encantado area in Moca and Isabela; and the Rio Camuy cave system in Hatillo and Camuy. In general, the degree of success varied with site and the geophysical method used. At some sites such as Pozo Brujo, the University of Puerto Rico Agricultural Experiment Station, and Monte Encantado area, natural potential anomalies strongly suggest the existence of conduits with flowing water. At most sites, however, the results obtained did not clearly reveal the presence of subsurface cavities that might be associated with the occurrence of conduit-controlled ground-water flow. Sites such as the University of Puerto Rico Agricultural Experiment Station, Pozo Brujo, and Quebrada de los Cedros warrant a more detailed analysis, including a test well drilling phase to confirm the presence of suspected high-yield water-bearing zones.

Water-Resources Investigations Report↗