Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “International Journal of Applied Earth Observations and Geoinformation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,690 records · Page 46Linked to original sources
USGS2024

Post-wildfire debris flows

Post-wildfire debris flows pose severe hazards to communities and infrastructure near and within recently burned mountainous terrain. Intense heat of wildfires changes the runoff characteristics of a watershed by combusting the vegetative canopy, litter, and duff, introducing ash into the soil and creating water repellant soils. Following wildfire, rainfall on bare ground is less able to infiltrate into the fire-altered soils and overland flow is less impeded by vegetation. Rainfall runoff in recently burned areas can erode hillslopes owing to the removal of soil binding organic matter near the soil surface by fire. In channels, loose, dry-ravel deposits composed of sand and gravel are readily entrained by concentrated runoff in channels. Entrainment of soil on hillslopes and in channels bulks up the sediment concentration of the rainfall runoff to generate debris flows capable of transporting boulders and large woody debris. Post-wildfire debris flows can be triggered by rainfall conditions that would typically produce little runoff during unburned conditions. The primary rainfall trigger for post-wildfire debris flows is high intensity rainfall during short duration convective rainstorms or periods of high rainfall intensity embedded within a long-duration frontal storm. Numerous observations of debris flows triggered by storms lasting less than an hour following periods of little to no rainfall indicate that antecedent rainfall is not a requirement for initiation of post-wildfire debris flows. Post-wildfire debris-flow hazard assessment entails estimating probability and magnitude of debris flows in the burned area, estimating debris-flow runout and intensity, and defining rainfall intensity-duration thresholds for debris-flow initiation. In the United States, probability and magnitude is estimated using empirically derived models largely based on data collected in southern California. The models provide maps to identify watersheds and drainage paths where post-wildfire hazards are most pronounced. Rainfall intensity-duration thresholds can be incorporated into flood hazard forecasting tools. Currently, work is underway to identify how to best implement debris-flow runout models in burned areas with efficiency and accuracy. Post-wildfire debris flows have been a long-recognized process in the Transverse Ranges of southern California; however, climate change is driving more frequent wildfires to burn more mountainous terrain throughout the western United States and worldwide. As a result, post-wildfire debris flows are becoming a more common threat in areas where they were once infrequent. As the threat of post-wildfire debris flow expands into new areas, evaluating the hazard becomes challenging because the degree to which wildfire increases debris-flow susceptibility varies from region to region. This chapter summarizes the knowledge to date for evaluating post-wildfire debris-flow susceptibility and hazard assessment. We summarize the characteristics of wildfire burn severity, topography, underlying soil and geology, and rainfall conditions that contribute to making a watershed most likely to produce post-wildfire debris flows. Methods for hazard assessment in the United States and other countries are summarized. We highlight knowledge gaps for how post-wildfire debris-flow susceptibility varies throughout the western United States and worldwide and identify research needs to improve hazard assessment methods in different geographies.

Book chapter↗
USGS2025

Updating and recalibrating the integrated Santa Rosa Plain Hydrologic Model to assess stream depletion and to simulate future climate and management scenarios in Santa Rosa, Sonoma County, California

The Santa Rosa Plain Hydrologic Model (SRPHM) was developed and published in 2014 through a collaboration between the U.S. Geological Survey (USGS) and Sonoma Water to analyze the hydrologic system in the Santa Rosa Plain watershed, help meet the increasing demand for fresh water, and prepare for future uncertainties in water resources. The original model simulated hydrological conditions and water use from water years 1975 to 2010. Recently (2023), the USGS, in cooperation with Sonoma Water and the California State Water Resources Control Board, updated the SRPHM model to extend its simulation period to the end of the 2018 calendar year, incorporate new estimates of rural and agricultural water use, and use efficient input format for climate variables. The updated model was recalibrated, and evaluation of the new model calibration is included in this report. This report presents the results of comparing the hydraulic heads, streamflow, and groundwater budget simulated by the updated model with those generated by the original model and observed data. The main difference in the simulated budget between the original and updated SRPHM is the estimates of agricultural pumping, rural domestic pumping, and return flow generated from rural water use that was not simulated in the original model. The revised agricultural pumping is simulated using the agricultural package, which constrains pumping to available groundwater. The use of the agricultural package leads to a more realistic estimation of agricultural water use, with revised agricultural pumping being one-third less than that in the original model. The revised rural pumping is about half of the pumping in the original model because of using detailed parcel data to estimate population density in rural areas instead of coarse census tracts. Overall, average total inflows for water years 2006–10 simulated by the updated model were about 2 percent less than the original model, and the average total updated outflows were nearly 5 percent less than the original model. The updated model was then used to generate stream depletion maps, simulate climate change scenarios during 2019–99, and simulate water rights allocation using the Model for Decision Support in Integrated River Basin Management (MODSIM). The results from simulating eight future climate scenarios indicated either an increase in groundwater storage or no significant change in the next 80 years, along with an increase in recharge, an increase in actual evapotranspiration in six out of eight climate projections, and an increase in surface runoff. The increases in the simulated future groundwater storage, recharge, evapotranspiration, and runoff in most climate projections are mainly driven by the projected increase in precipitation in most of the future climate scenarios. The updated model also was used to test a pilot case study demonstrating water-resource allocation among different users with different water rights using the integrated MODSIM-Groundwater and Surface-Water Flow Model (GSFLOW) platform. The updated SRPHM serves as a valuable tool for analyzing historical and future hydrologic conditions in the Santa Rosa Plain watershed and preparing for future uncertainties.

California↗
USGS1996

Hydrogeologic investigation and simulation of ground-water flow in the Upper Floridan Aquifer of north-central Florida and southwestern Georgia and delineation of contributing areas for selected city of Tallahassee, Florida, water-supply wells

A 4-year investigation of the Upper Floridan aquifer and ground-water flow system in Leon County, Florida, and surrounding counties of north-central Florida and southwestern Georgia began in 1990. The purpose of the investigation was to describe the ground-water flow system and to delineate the contributing areas to selected City of Tallahassee, Florida, water-supply wells. The investigation was prompted by the detection of low levels of tetrachloroethylene in ground-water samples collected from several of the city's water-supply wells. Hydrologic data and previous studies indicate that; ground-water flow within the Upper Floridan aquifer can be considered steady-state; the Upper Floridan aquifer is a single water-bearing unit; recharge is from precipitation; and that discharge occurs as spring flow, leakage to rivers, leakage to the Gulf of Mexico, and pumpage. Measured transmissivities of the aquifer ranged from 1,300 ft 2 /d (feet squared per day) to 1,300,000 ft2/d. Steady-state ground-water flow in the Upper Floridan aquifer was simulated using a three-dimensional ground- water flow model. Transmissivities ranging from less than 5,000 ft2/d to greater than 11,000,000 ft 2 /d were required to calibrate to observed conditions. Recharge rates used in the model ranged from 18.0 inches per year in areas where the aquifer was unconfined to less than 2 inches per year in broad areas where the aquifer was confined. Contributing areas to five Tallahassee water-supply wells were simulated by particle- tracking techniques. Particles were seeded in model cells containing pumping wells then tracked backwards in time toward recharge areas. The contributing area for each well was simulated twice, once assuming a porosity of 25 percent and once assuming a porosity of 5 percent. A porosity of 25 percent is considered a reasonable average value for the Upper Floridan aquifer; the 5 percent porosity simulated the movement of ground-water through only solution-enhanced bedding plains and fractures. The contributing areas were generally elliptical in shape, reflecting the influence of the sloping potentiometric surface. The contributing areas delineated for a 5 percent porosity were always much larger than those determined using a 25 percent porosity. The lowest average ground-water velocity computed within a contributing area, using a 25 percent porosity, was 1.0 ft/d (foot per day) and the highest velocity was 1.6 ft/d. The lowest average ground-water velocity, determined using a 5 percent porosity, was 2.4 ft/d and the highest was 7.4 ft/d. The contributing areas for each of the five wells was also determined analytically and compared to the model-derived areas. The upgradient width of the simulated contributing areas were larger than the upgradient width of the analytically determined contributing areas for four of the five wells. The model could more accurately delineate contributing areas because of the ability to simulate wells as partially penetrating and by incorporating complex, three-dimensional aquifer characteristics, which the analytical method could not.

Florida, Georgia↗
USGS2024

Upper crustal seismic velocity structure of the Hayward fault zone, San Francisco Bay, California, USA: Results from the 2016 East Bay Seismic Experiment (EBSI-16)

We developed Vp, Vs, Vp / Vs ratio, and Poisson’s ratio models of the uppermost crust (<4 km depth) from the eastern San Francisco (SF) Bay (California, USA) to near the Calaveras fault along a 15-km-long, linear profile. Upper crustal velocities are highly variable beneath, west, and well east of the Hayward fault. We observe eight notable features, from west to east: (1) Near San Francisco Bay, there is an ~2-km-wide structure with high Vp / Vs ratios (up to 5) and Poisson’s ratios (up to 0.48) extending from the surface to the base of our model, which we suggest the structure is a near-vertical fault that lies along a straight-line projection between the Silver Creek fault to the south and the Point Richmond fault to the north. The structure may be part of an ~90-km-long fault along the eastern SF Bay. (2) The western East Bay Plain, the lower lying area between the bay and the hills, includes up to 800 m of low-velocity sediments ( Vp ~1600–3000 m/s, Vs ~500 m/s to ~1000 m/s), underlain by higher velocity basement rocks ( Vp ~3000–5800 m/s; Vs ~1000–1500 m/s). (3) Between ~1 km and 3 km east of the Bay shoreline, sediments thin in a series of steps (likely faults) toward the Hayward fault. (4) Between ~3 km west and ~1 km east of the Hayward fault (at the East Chabot fault) at depths greater than 1 km, basement Vp (up to 6000 m/s) and Vs (up to 2800 m/s) are high, and Vp / Vs ratios (<2) and Poisson’s ratios (<0.3) are low, suggesting crystalline rocks. Furthermore, a near-vertical zone of low Vp / Vs ratios and Poisson’s ratios is between near-surface traces of the Hayward and East Chabot faults, likely corresponding to the San Leandro Gabbro of Ponce et al. (2003) . (5) Eastward of the East Chabot fault in the upper 1.5 km, basement Vp (~3000 m/s to ~4200 m/s) and Vs (~1200–2000 m/s) are lower than those west of the fault. (6) In the eastern Hayward/Oakland Hills, there are zones of laterally varying, high- and low-velocity ( Vp ~2500–3000 m/s) Jurassic–Cretaceous and Tertiary sediments in the shallow subsurface that likely extend much deeper than imaged. (7) Seismic energy that propagates westward from sources east of the Hayward fault (HF) appear weaker than energy that propagates eastward from sources west of the HF, suggesting that the HF acts as a partial barrier to shallow seismic energy propagation into the more populated eastern SF Bay area. (8) Unlike many fault zones, it appears that the active trace of the Hayward fault (in our study area) is not cored by a prominent, low-velocity zone relative to rocks to the east and west of the active trace. However, the active trace does mark a prominent change from relatively higher velocities to the west and lower velocities to the east.

California↗
USGS2025

Completion summary for monitor wells NRF-17 and NRF-18 at the Naval Reactors Facility, Idaho National Laboratory, Idaho

The U.S. Geological Survey (USGS)—in cooperation with the U.S. Department of Energy (DOE) for the Naval Reactors Laboratory Field Office that supports operations for the Naval Reactors Facility (NRF) located at the Idaho National Laboratory (INL)—drilled and constructed well NRF-17 (formerly borehole USGS 151) and well NRF-18 (formerly borehole USGS 152) for stratigraphic framework analyses and water-quality monitoring at the Idaho National Laboratory (INL) near the NRF, in southeastern Idaho. Borehole USGS 151 was continuously cored from about 48 to 1,070 feet (ft) below land surface (BLS); rotary drilled from approximately 1,070 to 1,720 ft BLS; and re-drilled to complete construction as a monitor well NRF-17, completed to 461 ft BLS. Borehole USGS 152 was continuously cored from approximately 19 to 1,259 ft BLS; rotary drilled from approximately 1,259 to 1,630 ft BLS; and re-drilled to complete construction as a monitor well NRF-18, completed to 450 ft BLS. Geophysical data were examined with photographed core material to record lithologic descriptions and to suggest zones where groundwater flow was anticipated. Basalt flows varied from highly fractured to dense, with high-to-low vesiculation. Well NRF-17 generally was constructed in mostly dense basalt (greater than 75 percent), and well NRF-18 was constructed in primarily fractured and (or) vesicular basalt. In well NRF-17, the well capacity is directly affected by the limited amount of fractured basalt, which serves as the primary pathway for groundwater. This effect was observed during the pumping test conducted after the well's final construction. Single-well aquifer tests were done at wells NRF-17 and NRF-18 to provide estimates of transmissivity and hydraulic conductivity after final well construction and initial well development. Estimated values of transmissivity and hydraulic conductivity for well NRF-17 were 8.81 feet squared per day (ft 2 /d) and 1.04×10 -2 feet per day (ft/d), respectively. Estimated values of transmissivity and hydraulic conductivity for well NRF-18 were 4.77×10 3 ft 2 /d and 5.61 ft/d, respectively. The NRF-17 pump test resulted in 19.41 ft of measured drawdown at a sustained average pumping rate of 3.3 gallons per minute (gal/min). The NRF-18 pump test resulted in 0.55 ft of measured drawdown at a sustained average pumping rate of 31.0 gal/min. Water-quality samples collected from the two wells were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Water samples for select inorganic constituents showed concentrations consistent with signatures from tributary valley groundwater with influences from ephemeral surface-water recharge from the Big Lost River. Water-quality samples analyzed for stable isotopes of oxygen and hydrogen are consistent with signatures from tributary valley groundwater and surface-water recharge inputs to the aquifer. No measured water-quality results were greater than their respective maximum contaminant levels for public drinking-water supplies. Inorganic and nutrient water-quality results for well NRF-17 and well NRF-18 suggest the groundwater in this area is potentially affected by industrial wastewater disposal.

Idaho↗
USGS2026

Bedrock geologic map of the Eagle Lake quadrangle, Essex County, New York

The bedrock geology of the 7.5-minute Eagle Lake quadrangle, Essex County, New York, consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Granulite facies Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 giga-annum (Ga, billion years before present). The earliest of four phases of deformation (D1) predated AMCG magmatism and is characterized by gneissosity, rarely preserved F1 isoclinal folds, and migmatite in the paragneiss host rocks. A sample of hornblende quartz syenite from the AMCG suite, collected from an abandoned railroad cut on Old Furnace Road, yielded a U-Pb zircon age of 1,149±10 million years before present. D2 deformation produced a composite penetrative gneissosity, migmatite, and isoclinal F2 folds. Towards the end of D2, felsic magmatism (including the regionally extensive Lyon Mountain Granite Gneiss, abbreviated “LMG”) spread by penetrative migration as semiconcordant alkali feldspar granite sheets subparallel to S2 into the previously deformed lithologies. The LMG crystallized at approximately 1.15 to 1.14 Ga and displays synkinematic F2 folds thus constraining the time of D2 deformation. Exhumation of the Marcy anorthosite began during D3 along a mylonitic extensional detachment, as a type of core complex. Protracted D3 produced F3 folds exhibited in regional domes and basins, such as the Hammondville antiform, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. D4 created NE- and NW-trending boudinage, local high-grade ductile shear zones, and crosscutting granitic pegmatite dikes. Kilometer (km)-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. Lower Paleozoic rocks are part of the Early Cambrian to Late Ordovician great American carbonate bank on the ancient margin of Laurentia. The Potsdam Sandstone preserves the Cambrian stratigraphy in outliers above the Great Unconformity. The Paleozoic rocks are weakly folded and block faulted. Parts of the quadrangle are covered by undifferentiated glacial deposits, but much of the quadrangle contains only a variably thick, veneer of unmapped glacial till over significant areas of exposed bedrock. The map also shows waste rock piles and locations of historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondack Mountains, and provide a modern context for historical mines. This Scientific Investigations Map of the Eagle Lake 7.5-minute quadrangle consists of a map sheet, an explanatory pamphlet, and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information. The map sheet includes a bedrock geologic map, a correlation of map units, a description of map units, an explanation of map symbols, and two cross sections. The explanatory pamphlet includes a discussion of the geology.

New York↗
USGS2024

Hydrogeologic conceptual model of groundwater occurrence and brine discharge to the Dolores River in the Paradox Valley, Montrose County, Colorado

Salinity, or total dissolved solids (TDS), of the Colorado River is a major concern in the southwestern United States where the river provides water to about 40 million people for municipal and industrial use and is used to irrigate about 5.5 million acres of land. Much of the salinity in the Colorado River Basin is derived from natural interactions of surface water and groundwater with various geologic materials (rocks, soils, and alluvial deposits). The Dolores River in southwest Colorado is a major tributary of the Colorado River that historically accounts for about 6 percent of the salinity load to the Upper Colorado River Basin with the Paradox Valley being the primary source of salinity to the Dolores River. The Paradox Valley, one of several salt-anticline valleys in the region, is a fault-bounded topographic basin aligned with and exposing an underlying salt-anticline core. Salt deposits in the Pennsylvanian Paradox Formation of the Hermosa Group form an elongated salt diapir oriented northwest to southeast that is up to 12,000 feet (ft) thick beneath the present valley floor. Surface erosion, groundwater circulation, and weathering during Tertiary and Quaternary valley formation contributed to development of a cap rock, collapse features, breccia, and brine at the top of the exposed salt diapir. Today (2023), brine occurring in the brecciated cap rock and underlying salt deposits is in hydraulic connection with an overlying freshwater alluvial aquifer, and depending on seasonal river stage and hydrologic conditions, the brine discharges to the Dolores River causing the observed increase in salinity as the river crosses the Paradox Valley. To reduce salinity concentrations in the Dolores River, the Bureau of Reclamation (Reclamation) operates the Paradox Valley Unit (PVU). The PVU project consists of nine shallow brine pumping wells near the Dolores River and one deep disposal well where the brine is injected for disposal. When operational, the PVU pumping wells extract brine from the base of the alluvial aquifer that is piped and injected into a deep disposal well about 3 miles southwest of the PVU. The PVU became fully operational July 1, 1996, and by 2015, operation of the PVU had reduced salinity concentrations in the Dolores River by as much as 70 percent compared to pre-PVU conditions. In response to a 4.5 magnitude earthquake, injection operations, and thus PVU pumping, were ceased from March 2019 to June 2022. A trial period of PVU operation began in June 2022 with a reduced injection rate, and thus PVU pumping rate, of about two-thirds capacity to gather additional information and guide future operational decisions. In cooperation with Reclamation, the U.S. Geological Survey (USGS) developed this report to present the current (2023) understanding of groundwater and brine occurrence and discharge to the Dolores River in the Paradox Valley. Results from the compilation of spatial datasets, groundwater sampling and age dating, and aquifer tests are presented to provide improved understanding of the Paradox Valley hydrogeology, to supply datasets for a numerical groundwater-flow and brine-transport model, and to support future operations of the PVU. The hydrogeologic data provided herein, along with the most recent loading analysis for the Dolores River in the Paradox Valley, and a previous conceptual model for brine discharge to the river are used to present a conceptual understanding of groundwater occurrence in the Paradox Valley.

Colorado↗
USGS2025

Depth of magma crystallization and fluid exsolution beneath the porphyry-skarn Cu deposits at Santa Rita and Hanover-Fierro, New Mexico, USA

The depth level at which porphyry Cu–forming magmas fractionated and exsolved mineralizing fluids is actively debated. In the classic model, extensive magma fractionation occurs in large, upper crustal magma chambers, and concomitant fluid exsolution leads to forceful expulsion of residual magmas in the form of porphyry dikes, stocks, and breccia pipes, which subsequently serve as pathways for the mineralizing fluids. In contrast, some recent studies highlighting the role of deep crustal magma fractionation in the production of fertile magmas essentially deny the existence of upper crustal magma chambers at the time of mineralization. To address this, we conducted a detailed thermobarometric investigation of 13 intermediate to felsic, porphyritic intrusive rocks related to porphyry-skarn Cu mineralization at Santa Rita and Hanover-Fierro, New Mexico, United States, representing two premineralization magmas (61–60 Ma), seven synmineralization magmas (60–58 Ma), and four late- to postmineralization magmas (58–57 Ma). For each sample, the pressure of last magma crystallization before final magma ascent to the current exposure level was reconstructed based on Al-in-hornblende barometry of small hornblende inclusions trapped within quartz phenocrysts and through titanium-in-quartz (TitaniQ) thermobarometry of the host quartz phenocrysts themselves. Since quartz is one of the last crystallizing magmatic minerals, and no significant phenocryst growth could have occurred in small dikes and stocks after final magma emplacement, quartz phenocrysts and their contained hornblende inclusions record the depth of last magma crystallization before final magma ascent. When present, hornblende phenocrysts and hornblende inclusions within other major phenocrysts were also analyzed. Both quartz and hornblende barometers return consistent average pressures of 3.2 ± 0.4 kbar for the entire suite of pre- to postmineralization magmas, corresponding to depths of 11 to 14 km. The synmineralization magmas return even more consistent average pressures of 3.1 ± 0.2 kbar, corresponding to a depth of 12 ± 1 km. The volume of the mineralizing porphyry dikes and stocks at the emplacement level is far too small to have provided all the fluids and metals required to form the observed ore deposits. Therefore, the majority of the ore-forming fluids must have originated from the magmas that crystallized at 12 ± 1 km depth. The ore deposits, conversely, formed at ~5-km paleodepth. This implies that most of the mineralizing fluids traveled an average vertical distance of ~7 km from their magmatic source to the eventual site of ore precipitation. The relatively unaltered nature and low veining degree of deeper parts of mineralized porphyry dikes and stocks suggest that the fluid transport through these intrusive bodies occurred mostly at near-solidus conditions by means of fluid percolation along grain boundaries. In summary, our results suggest that (1) a large, upper crustal pluton exists ~7 km beneath the Santa Rita and Hanover-Fierro deposits; (2) abundant phenocryst crystallization occurred at this depth level; and (3) this pluton was the main source for the exsolution of ore-forming fluids. However, the investigated rocks have elevated whole-rock Sr/Y ratios, indicating magma fractionation at deep crustal levels. As a result, our preferred model is a combination of the two end-member models introduced above, with most magma fractionation having occurred in the deep crust and with residual, intermediate to felsic melts having ascended and accumulated at 11 to 14 km paleodepth, where they continued to crystallize with comparatively little crystal-liquid separation, before some of these magmas ascended further to shallow levels and quenched to porphyries.

New Mexico↗
USGS1999

Episodic sediment-discharge events in Cascade Springs, southern Black Hills, South Dakota

Cascade Springs is a group of artesian springs in the southern Black Hills, South Dakota, with collective flow of about 19.6 cubic feet per second. Beginning on February 28, 1992, a large discharge of red suspended sediment was observed from two of the six known discharge points. Similar events during 1906-07 and 1969 were documented by local residents and newspaper accounts. Mineralogic and grain-size analyses were performed to identify probable subsurface sources of the sediment. Geochemical modeling was performed to evaluate the geochemical evolution of water discharged from Cascade Springs. Interpretations of results provide a perspective on the role of artesian springs in the regional geohydrologic framework. X-ray diffraction mineralogic analyses of the clay fraction of the suspended sediment were compared to analyses of clay-fraction samples taken from nine geologic units at and stratigraphically below the spring-discharge points. Ongoing development of a subsurface breccia pipe(s) in the upper Minnelusa Formation and/or Opeche Shale was identified as a likely source of the suspended sediment; thus, exposed breccia pipes in lower Hell Canyon were examined. Upper Minnelusa Formation breccia pipes in lower Hell Canyon occur in clusters similar to the discrete discharge points of Cascade Springs. Grain-size analyses showed that breccia masses lack clay fractions and have coarser distributions than the wall rocks, which indicates that the red, fine-grained fractions have been carried out as suspended sediment. These findings support the hypothesis that many breccia pipes were formed as throats of abandoned artesian springs. Geochemical modeling was used to test whether geochemical evolution of ground water is consistent with this hypothesis. The evolution of water at Cascade Springs could not be suitably simulated using only upgradient water from the Minnelusa aquifer. A suitable model involved dissolution of anhydrite accompanied by dedolomitization in the upper Minnelusa Formation, which is caused by upward leakage of relatively fresh water from the Madison aquifer. The anhydrite dissolution and dedolomitization account for the net removal of minerals that would lead to breccia pipe formation by gravitational collapse. Breccia pipes in the lower Minnelusa Formation are uncommon; however, networks of interconnected breccia layers and breccia dikes are common. These networks, along with vertical fractures and faults, are likely pathways for transmitting upward leakage from the Madison aquifer. It is concluded that suspended sediment discharged at Cascade Springs probably results from episodic collapse brecciation that is caused by subsurface dissolution of anhydrite beds and cements of the upper Minnelusa Formation, accompanied by replacement of dolomite by calcite. It is further concluded that many breccia pipes probably are the throats of artesian springs that have been abandoned and exposed by erosion. The locations of artesian spring-discharge points probably have been shifting outwards from the center of the Black Hills uplift, essentially keeping pace with regional erosion over geologic time. Thus, artesian springflow probably is a factor in controlling water levels in the Madison and Minnelusa aquifers, with hydraulic head declining over geologic time, in response to development of new discharge points. Development of breccia pipes as throats of artesian springs would greatly enhance vertical hydraulic conductivity in the immediate vicinity of spring-discharge points. Horizontal hydraulic conductivity in the Minnelusa Formation also may be enhanced by dissolution processes related to upward leakage from the Madison aquifer. Potential processes could include dissolution resulting from leakage in the vicinity of breccia pipes that are abandoned spring throats, active spring discharge, development of subsurface breccias with no visible surface expression or spring discharge, as well as general areal leakage from the Madison aquifer into the Minnelusa Formation.

South Dakota↗
USGS2026

Preliminary bedrock geologic map of the Port Henry quadrangle, Essex County, New York, and Addison County, Vermont

Introduction The bedrock geology of the 7.5-minute Port Henry quadrangle consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 Ga (giga-annum). In the Port Henry quadrangle, the AMCG metaigneous rocks (Yhg, Ygb, Yanw) intruded older, mostly metasedimentary rocks of the Grenville Complex during the middle to late Shawinigan orogeny (~1,160–1,150 Ma [mega-annum]). All rocks were subsequently metamorphosed to upper amphibolite to granulite facies conditions during the 1,080–1,050 Ma Ottawan orogeny. New mapping reveals four periods of deformation: (1) D1 produced rarely preserved isoclinal folds in the paragneiss and marble and predates AMCG magmatism. (2) Subsequent D2 deformation produced the dominant gneissic fabric preserved in the rock, recumbent folding, and deformed all the Proterozoic units in the map area. Syn- to late-D2 felsic magmatism resulted in the regionally extensive Lyon Mountain Granite Gneiss, which hosts numerous magnetite ore bodies. (3) Mylonitic extensional shear zones and core complex formation marked the beginning of D3 deformation. Protracted D3 deformation resulted in F3 upright folding, dome and basin formation, pegmatite intrusion, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron-ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. (4) D4 created northeast- and northwest-trending local high-grade ductile shear zones and boudinage, northwest-trending regional kilometer (km)-wide ductile shear zones, and crosscutting granitic pegmatite dikes. The development of the late-stage regional shear zones (D4) was likely due to the continuation of extensional doming and uplift from upper amphibolite facies conditions at the end of the Ottawan orogeny. The majority of iron-ore deposits in the Port Henry and adjacent Witherbee quadrangles are in the hanging wall of these extensional shear zones. In the Port Henry quadrangle, the km-wide Cheney Mountain shear zone is the result of D4 deformation. Kilometer-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. The Paleozoic rocks are part of the Early Cambrian to Late Ordovician carbonate bank on the ancient margin of Laurentia. The approximately 1-km-thick Cambrian to Ordovician stratigraphy records a transition from synrift clastics to passive-margin peritidal carbonate buildups to gradually deeper-water subtidal- to shelf-carbonates during foreland basin development associated with the Taconic orogeny. The Paleozoic rocks are weakly folded and block faulted. Large areas of the Champlain Valley are covered by undifferentiated glacial deposits, some of which contain mapped landslides. The map also shows waste rock piles and tailings from historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondacks, provide a context for historical iron mines in the eastern Adirondacks, and update the stratigraphy of the Champlain Valley in New York and Vermont. This Open-File Report includes a bedrock geologic map; a description of map units; a correlation of map units; and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information.

New York, Vermont↗
USGS2021

Geology, mineralogy, and cassiterite geochronology of the Ayawilca Zn-Pb-Ag-In-Sn-Cu deposit, Pasco, Peru

The Ayawilca deposit in Pasco, Peru, represents the most significant recent base-metal discovery in the central Andes and one of the largest undeveloped In resources globally. As of 2018, it hosts an 11.7 Mt indicated resource grading 6.9% Zn, 0.16% Pb, 15 g/t Ag, and 84 g/t In, an additional 45.0 Mt inferred resource grading 5.6% Zn, 0.23% Pb, 17 g/t Ag, and 67 g/t In, and a separate Sn-Cu-Ag inferred resource of 14.5 Mt grading 0.63% Sn, 0.21% Cu, and 18 g/t Ag. Newly obtained U–Pb dates for cassiterite by LA-ICP-MS (22.77 ± 0.41 and 23.05 ± 2.06 Ma) assign the Ayawilca deposit to the Miocene polymetallic belt of central Peru. The polymetallic mineralization occurs as up to 70-m-thick mantos hosted by carbonate rocks of the Late Triassic to Early Jurassic Pucará Group, and subordinately, as steeply dipping veins hosted by rocks of the Pucará Group and overlying Cretaceous sandstones-siltstones of the Goyllarisquizga Group. Relicts of a distal retrograde magnesian skarn and cassiterite (stage pre-A) were identified in the deepest mantos. The volumetrically most important mineralization at Ayawilca comprises a low-sulfidation assemblage (stage A) with quartz, pyrrhotite, arsenopyrite, chalcopyrite, Fe-rich sphalerite, and traces of stannite and herzenbergite. Stage A sphalerite records progressive Fe depletion, from 33 to 10 mol% FeS, which is compatible with the observed transition from low- to a subsequent intermediate-sulfidation stage (B) marked by the crystallization of abundant pyrite and marcasite. Finally, during a later intermediate-sulfidation stage (C) sphalerite (up to 11 mol% FeS), galena, native bismuth, Cu-Pb-Ag sulfosalts, siderite, Mn-Fe carbonates, kaolinite, dickite, and sericite were deposited. This paragenetic evolution shows striking similarities with that at the Cerro de Pasco Cordilleran-type polymetallic deposit, even if at Ayawilca stage C did not reach high-sulfidation conditions. The occurrence of an early retrograde skarn assemblage suggests that the manto bodies at Ayawilca formed at the transition between distal skarn and skarn-free (Cordilleran-type) carbonate-replacement mineralization. Mineral assemblages define a T- f S 2 evolutionary path close to the pyrrhotite-pyrite boundary. Buffering of hydrothermal fluids by underlying Devonian carbonaceous phyllites of the Excelsior Group imposed highly reduced conditions during stage A mineralization (log f O 2 < − 30 atm). The low f O 2 favored efficient Sn mobility during stages pre-A and A, in contrast to other known ore deposits in the polymetallic belt of central Peru, in which the occurrence of Sn minerals is minor. Subsequent cooling, progressive sealing of vein walls, and decreasing buffering potential of the host rocks promoted the shift from low- (stage A) to intermediate-sulfidation (stages B and C) states. LA-ICP-MS analyses reveal significant In contents in Fe-rich sphalerite (up to 1.7 wt%), stannite (up to 1908 ppm), and chalcopyrite (up to 1185 ppm). The highest In content was found in stage A sphalerite that precipitated along with chalcopyrite and stannite, thus pointing to the early, low-sulfidation assemblage as prospective for this high-tech metal in similar mineral systems. Indium was likely incorporated into the sphalerite crystal lattice via Cu + + In 3+ ↔ 2 Zn 2+ and (Sn, Ge) 4+ + (Ga, In) 3+ + (Cu + Ag) + ↔ 4 Zn 2+ coupled substitutions. Indium incorporation mechanisms into the stannite and chalcopyrite crystal lattices remain unclear.

Pasco↗
USGS2024

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri River between Kansas City and St. Louis, Missouri, May 19–26, 2021

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near nine bridges at eight highway crossings of the Missouri River between Kansas City and St. Louis, Missouri, from May 19 to 26, 2021. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 to 1,840 feet (ft) longitudinally and generally extending laterally across the active channel from bank to bank during low to moderate flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a low to moderate flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All the bridge sites in this study were previously surveyed and documented in previous studies. Comparisons between bathymetric surfaces from the previous surveys and those of the current (2021) study do not indicate any consistent correlation between channel-bed elevations and streamflow conditions. The average difference between the bathymetric surfaces varied from 1.59 ft higher to 0.95 ft lower in 2021 than 2017, which corresponds to a gain of 100,200 cubic yards and a loss of 55,800 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 2.74 ft higher to 3.05 ft lower in 2021 than 2013, which corresponds to a gain of 111,500 cubic yards and a loss of 169,200 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 4.52 ft higher to 1.38 ft lower in 2021 than 2011, which corresponds to a gain of 221,100 cubic yards and a loss of 90,300 cubic yards, respectively. The most substantial overall net gain was 221,100 cubic yards between 2011 and 2021 at structures L0550 and A4497 at Jefferson City (site 20). The large net gain likely results from a combination of the mitigation of the scour holes near pier 4 of both bridges and the substantially lower flow in 2021 than in 2011. Alternatively, the most substantial overall net loss was 169,200 cubic yards between 2013 and 2021 at structure A6288 at Hermann (site 21), despite comparable streamflows. Pier size, nose shape, and skew to approach flow had a substantial effect on the size of the scour hole observed at a given pier. Larger and deeper scour holes were present at piers with wide or blunt noses caused by exposed footings or caissons. When a pier was skewed to primary approach flow, the scour hole was generally deeper and larger than at a similar pier without skew; furthermore, the shape of the scour hole near skewed piers in this study generally was longer and deeper on the side with impinging flow. At structure A6288 at Hermann (site 21), the scour hole near pier 5 was difficult to discern from nearby dunes and ripples, whereas the upstream edge of the footing was visible at pier 4, which likely contributes to the larger scour hole near that pier; the top of the footing may blunt the horseshoe vortex at pier 5, but the exposed front of the footing may exacerbate the vortex at pier 4.

Missouri↗
USGS2025

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗
USGS2024

Simulated mean monthly groundwater-transported nitrogen loads in watersheds on the north shore of Long Island Sound, 1993–2022

Elevated nitrogen loads are pervasive in the Long Island Sound, an estuary that receives freshwater and nutrients from both surface-water and groundwater discharge. Surface-water nitrogen loads to the Long Island Sound are relatively well characterized, but less is known about groundwater-transported nitrogen loads. Prior work on the northern shore of Long Island Sound (Connecticut and areas of New York and Rhode Island) suggested that groundwater travel times are relatively short (median less than 2 years) and that decade-long nutrient legacies are not widespread. Because the travel times are short, groundwater flow and nutrient loads likely vary substantially between months. In the current study, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency’s Long Island Sound Study and the Connecticut Department of Energy and Environmental Protection, developed a set of models to better characterize spatial and temporal patterns of groundwater-transported nitrogen loading from atmospheric deposition, septic systems, and fertilizers within the study area. The models provide an estimate, with uncertainty, of groundwater-transported nitrogen loads in the study area, filling a key gap in the nitrogen budget for Long Island Sound. The models also highlight the spatial and temporal variation in nitrogen loading throughout the study area. The modeling workflow involved four models. (1) A soil-water-balance model was developed by using the Soil-Water-Balance software to simulate groundwater recharge across the study area for water years 2005 through 2022. The simulated mean monthly recharge from the soil-water-balance model was used as input into a groundwater-flow model. (2) The groundwater-flow model was developed by using the MODFLOW 6 software and data for water years 1993 through 2022 and simulates average monthly hydrologic conditions. The groundwater-flow model was calibrated by using the Iterative Ensemble Smoother method within the PEST++ software. The Iterative Ensemble Smoother method generates an ensemble of sets of parameter values, with each set producing reasonable simulated hydrologic parameter values. (3) An ensemble of MODPATH particle-tracking simulations were run to generate particle flow paths and travel times, with each simulation using a different set of the flow model parameters. (4) A nitrogen load model uses the MODPATH simulation outputs to track nitrogen from the land surface through multiple attenuation zones until it discharges into fresh or saline surface water. As with the groundwater-flow model, the nitrogen model simulated average monthly groundwater-transported nitrogen loads for water years 1993 through 2022. One novel aspect of the nitrogen load model is that the nitrogen attenuation parameters were calibrated to observed nitrogen loads. Across the ensemble of simulated nitrogen loads, the median study-area-wide monthly simulated nitrogen loads from the aquifer to Long Island Sound throughout the year ranged from 900 to 18,600 kilograms of nitrogen per day, with a median load of 5,100 kilograms of nitrogen per day. The simulated loads were based on average monthly conditions for water years 1993 through 2022. Loads were highest during the winter and early spring and lowest during the late summer. However, simulated travel times for groundwater and nitrogen loads discharged to Long Island Sound during summer were longer than travel times for groundwater and loads discharged during the winter, indicating that, on average, groundwater discharged during summer traveled along different, and longer, flow paths, than groundwater discharged during winter. This indicates that summer loads would respond more slowly to changes in nitrogen inputs at the water table than winter loads. Over the entire study area, approximately 15 percent of the simulated load is from atmospheric deposition sources, 30 to 40 percent is from fertilizer, and 50 to 60 percent is from septic systems. The final analysis of the study involved simulating the change in groundwater-transported nitrogen load in response to upgrading septic systems or reducing fertilizing inputs to areas of turf grass. Both management interventions reduced the groundwater-transported nitrogen load, and reductions were greater in areas with greater loads from septic systems or turf-grass fertilizers. The delay between management actions and substantial reductions in groundwater-transported nitrogen loads varied seasonally; loads during the late summer months remained elevated longer than the winter loads.

Connecticut, Rhode Island↗
USGS2024

Groundwater, surface-water, and water-chemistry data, Black Mesa area, northeastern Arizona—2019–2021

The Navajo (N) aquifer is an extensive aquifer and the primary source of groundwater in the 5,400-square-mile Black Mesa area in northeastern Arizona. Water availability is an important issue in the Black Mesa area because of the arid climate, past industrial water use, and continued water requirements for municipal use by a growing population. Precipitation in the area typically ranges from less than 6 to more than 16 inches per year, depending on location. The U.S. Geological Survey water-monitoring program in the Black Mesa area began in 1971 and provides information about the long-term effects of groundwater withdrawals from the N aquifer for industrial and municipal uses. This report presents the results of data collected as part of the monitoring program in the Black Mesa area from calendar years 2020–2021 and, additionally, uses streamflow statistics from November and December 2019. The monitoring program includes measurements of (1) groundwater withdrawals (pumping), (2) groundwater levels, (3) spring discharge, (4) surface-water discharge, and (5) groundwater chemistry. In calendar year 2020, total groundwater withdrawals were estimated to be 2,680 acre-feet (acre-ft), and, in 2021, total withdrawals were estimated to be 2,570 acre-ft. Total withdrawals during 2021 were about 65 percent less than total withdrawals in 2005 because the Peabody Western Coal Company discontinued its use of water to transport coal in a coal slurry pipeline after 2005 and ceased mining operations in 2019. Owing to Navajo Nation and Hopi Reservation access restrictions during the Coronavirus pandemic, water levels were not collected from municipal wells in 2020 or 2021. Water levels measured in 2021 from wells completed in the unconfined areas of the N aquifer within the Black Mesa area showed a decline in 7 of 13 wells when compared with water levels from the prestress period (prior to 1965). The changes in water levels across all 13 wells ranged from +8.4 feet (ft) to −42.4 ft, and the median change was −0.4 ft. Water levels also showed decline in 11 of 12 wells measured in the confined area of the aquifer when compared to the prestress period. The median change for the confined area of the aquifer was −25.9 ft, with changes across all 12 wells ranging from +17.3 ft to −133.7 ft. Spring flow was measured at four springs between 2020 and 2021. Flow fluctuated during the period of record for Burro Spring and Pasture Canyon Spring, but a decreasing trend was statistically significant (p<0.05) at Moenkopi School Spring and Unnamed Spring near Dennehotso, Arizona. Discharge at Burro Spring has remained relatively constant since it was first measured in the 1980s, and discharge at Pasture Canyon Spring has fluctuated for the period of record. Continuous records of surface-water discharge in the Black Mesa area were collected from streamflow-gaging stations at the following sites: Moenkopi Wash at Moenkopi 09401260 (1976–2021), Dinnebito Wash near Sand Springs 09401110 (1993–2020), Polacca Wash near Second Mesa 09400568 (1994–2020), and Pasture Canyon Springs 09401265 (2004–2021). Median winter flows (November through February) of each winter were used as an estimate of the amount of groundwater discharge at the above-named sites. For the period of record, the median winter flows have generally remained constant at Polacca Wash and Pasture Canyon Springs, whereas a decreasing trend was observed at Moenkopi Wash and Dinnebito Wash. In 2020 and 2021, water samples were collected from a total of four springs in the Black Mesa area and analyzed for selected chemical constituents. Results from the four springs were compared with previous analyses from the same springs. Dissolved solids, chloride, and sulfate concentrations increased at Moenkopi School Spring during the more than 30 years of record at that site. Concentrations of dissolved solids and sulfate at Pasture Canyon Spring have not varied significantly (p>0.05) since the early 1980s, and there is no increasing or decreasing trend in those data. However, concentrations of chloride from Pasture Canyon Spring show a diminishing trend. Concentrations of dissolved solids, chloride, and sulfate at Unnamed Spring near Dennehotso have varied for the period of record, but there is no statistical trend in the data. Concentrations of dissolved solids at Burro Spring have varied for the period of record, but there is no statistical trend in the data. However, concentrations of chloride and sulfate from Burro Spring show a trend towards lower concentrations.

Arizona↗
USGS2024

Evidence of nitrate attenuation in intertidal and subtidal groundwater in a subterranean estuary at a Cape Cod embayment, East Falmouth, Massachusetts, 2015–16

Nitrogen dynamics in intertidal and nearshore subtidal groundwater (subterranean estuary) adjacent to the Seacoast Shores peninsula, Falmouth, Massachusetts, were investigated during 2015–16 by the U.S. Geological Survey. The peninsula is a densely populated residential area with septic systems and cesspools that are substantial sources of nitrogen to groundwater. The study area is in the Eel River, an estuarine saltwater embayment connected to the ocean adjacent to the western shore of the peninsula, that was the subject of an earlier study by Colman and others (2018, https://doi.org/10.3133/sir20185095 ) on nitrogen transport and transformations in groundwater between onshore and offshore locations. The previous study documented the distribution of nitrate concentrations and nitrate attenuation reactions in fresh groundwater beneath the peninsula and the estuary. The current study extended those observations with more detailed sampling and analysis of shallow groundwater from wells near discharge sites beneath the estuary. The current field investigation included sampling of existing wells and installation and sampling of clusters of wells and temporary sampling points in the subterranean estuary, including (1) shallow transects 0.3 to 1.2 meters (m) deep extending from 1 to 13.5 m offshore and (2) deeper wells (from 1.83 to 4.88 m deep) extending from 4.3 to 14.3 m offshore. Measurements of hydraulic-head gradients 2–5 m below the sediment/water interface in the intertidal and nearshore subtidal zones indicated that groundwater flow generally was upwards (towards the estuary) under all tide conditions in October 2016. The magnitude of the gradient was greatest during low tide conditions, indicating that groundwater discharge likely decreased during high tides. Measurements of specific conductance in shallow groundwater in the subterranean estuary in three transects perpendicular to shore were consistent with the existence of saltwater flow cells (infiltration of overlying saline water, mixing with fresh groundwater, and discharge to the overlying saline water) in the intertidal and nearshore subtidal regions. The size of these flow cells was variable in space and time and dependent on the elevation of the tide (spring or neap). At this location in the Eel River subterranean estuary, and offshore to at least 13.5 m, offshore flow of fresh groundwater apparently prevented a deeper saltwater wedge from discharging to the surface. Nitrate concentrations in shallow groundwater (30 to 122 centimeters [cm] depth) were variable in space and time, ranging from not detectable to 600 micromoles per liter (μmol/L) (8.4 milligrams per liter as N), and were highest in June 2016 at depths from 61 to 122 cm below the sediment/water interface and from 4 to 9 m offshore. Nitrate generally was not detectable in saline shallow groundwater at 30-cm depth or at any depth from 30 to 122 cm from 10 to 13.5 m offshore. Dissolved oxygen concentrations were suboxic (less than 16 μmol/L) in 60 percent of the sampled subterranean groundwater beneath the intertidal and subtidal zones. In the remaining sites, the range of dissolved oxygen concentrations was from 18 to 272 μmol/L and the median concentration was 43 μmol/L. Evidence for microbial nitrate reduction (denitrification and possibly anammox) was provided by the distribution of the reaction product nitrogen gas (excess N 2 , or N 2MIC ), as determined from analysis of the dissolved nitrogen gas and argon gas (Ar) concentrations in groundwater samples. Excess nitrogen gas provided evidence for nitrate reduction in shallow groundwater below the subtidal and, to a lesser extent, intertidal zones adjacent to the Seacoast Shores peninsula. These zones, where evidence for nitrate reduction was detected, were in fresh and brackish groundwater near subtidal or intertidal saltwater cells where discharging fresh groundwater mixed with infiltrating saline water. Infiltrating seawater may have supplied organic carbon, one of several potential electron donors that are required for denitrification. Other potential electron donors, such as organic carbon, iron, manganese, hydrogen, methane, ammonium, elemental sulfur, or sulfide phases, may have been supplied by the estuarine sediments. Drainage from surface runoff near the shore also may have supplied organic carbon to fresh groundwater near the intertidal saltwater cell. The highest amounts of nitrate converted to excess nitrogen gas were estimated to be in the range of 230 to 430 μmol/L in nearly fresh groundwater near the subtidal saltwater cell at depths of 61 to 122 cm below the sediment/water interface and from 10 to 13.5 m offshore. Evidence of denitrification within 10 m of the shore was sparse (generally limited to less than 50 μmol/L of N 2 -N) despite the presence of high nitrate concentrations. The spatial distribution of estimated nitrate reduction in the intertidal and nearshore subtidal fresh and brackish groundwater may be related to local variability in the distribution of reactive electron donors in those zones. Variations in the amount of nitrate reduction to nitrogen gas were not clearly related to potential aqueous electron donors such as dissolved organic carbon, nor to potential reaction products such as alkalinity, but may have been controlled by combinations of aqueous and solid-phase reactants. The distribution of relatively shallow fresh groundwater containing nitrate could indicate potential nitrate discharge areas in the lower intertidal zone and uncertain locations farther offshore; however, the data did not extend all the way to the sediment/water interface or to the offshore freshwater limit. This study confirmed substantial loss of nitrate from some of the fresh and brackish groundwater in shallow subestuarine sediments prior to discharge but did not quantify how much nitrate eventually discharged to the estuary.

Massachusetts↗
USGS2025

Assessment of channel morphology, hydraulics, and bedload transport along the Siletz River, western Oregon

Significant Findings Chinook salmon ( Oncorhynchus tshawytscha ) and Pacific lamprey ( Entosphenus tridentatus ) are native, anadromous fish species in the Siletz River Basin, western Oregon, that face many threats to their survival in freshwater and the ocean. The Confederated Tribes of Siletz Indians of Oregon seek to mitigate freshwater threats to Chinook salmon and Pacific lamprey, where possible, with habitat conservation and restoration efforts. This study was conducted to assist the Confederated Tribes of Siletz Indians of Oregon in documenting and understanding the hydrogeomorphic processes shaping present-day habitat conditions and assessing future habitat implications for Chinook salmon and Pacific lamprey along the main-stem Siletz River. As such, this study focused on understanding geomorphic processes and patterns of channel change, including lateral and vertical adjustments in channel position and changes in bed-material sediment (sands, gravels, and cobbles that mantle the channel bed), which collectively determine overall patterns of channel morphology and fluvial habitats. Objective One was to evaluate lateral changes in channel position, vertical changes in bed elevation, and longitudinal patterns in bed-material particle size along the Siletz River using detailed channel maps developed from aerial photographs collected from 1939 to 2016, long-term records of stage and discharge collected by the U.S. Geological Survey (USGS) near the City of Siletz, and sediment particle size data. Objective Two was to assess hydraulic conditions using one- and two-dimensional hydraulic models and transport capacity of bed-material sediment using bedload transport models and sediment particle size data for a range of discharge conditions. Objective Three was to identify potential burrowing habitat for lamprey larvae (PBH) along the Siletz River network and provide insights in local factors influencing PBH along the main-stem Siletz River. The overall findings are synthesized to describe habitat implications for Chinook salmon and Pacific lamprey under present-day and future conditions. Results of Objective One, an evaluation of changes in channel position and bed elevations and longitudinal patterns in bed-material particle size along the Siletz River, include the following From 1939 to 2016, channel planform and the mapped area of gravel bars did not change considerably along the 97.2-kilometers (km) of Siletz River between Elk Creek and Millport Slough, except for in short sections generally less than 1 km long. This inherent lateral channel stability results from the resistant bedrock and terraces that bound most of the channel and limit lateral changes in channel position. Intermittent sections along the study reach where the active channel widened at channel bends displayed noticeable planform changes and increases in mapped bar area. From water year (WY; a 12-month period from October 1 through September 30 and named for the year in which it ends) 1906 to 2021, changes in the stage-discharge relation interpreted as rising and lowering channel bed levels were observed at the USGS streamgage 14305500 (Siletz River at Siletz, OR) in response to floods (such as high flows in February 1996 and January 2002 that exceeded 0.1 and 0.667 annual exceedance probabilities [AEP] events, respectively). However, the rating curve representing the stage-discharge relation did not change in response to high-magnitude floods between 2007 and 2021. Along the approximately 54-km of the Siletz River between Moonshine Park and the Bulls Bag area, surficial particle distributions varied considerably between sampling sites in response to changes in channel width and gradient, sediment inputs from tributaries, and basin geology. Despite this variability, median particle sizes tended to decrease in size in the downstream direction over the 54 km. Results of Objective Two, an evaluation of hydraulic and bedload transport conditions along the Siletz River, include the following The most substantial increases in maximum and mean water velocity and bedload sediment transport capacity occurred at events between the 0.995 and 0.50 AEPs. Events of these magnitudes occur approximately every 1–2 years. Smaller events (0.995 AEP) are generally contained by the banks of the main channel, whereas larger events (0.50 AEP) generally spill over the banks and inundate high-elevation bar and low-elevation floodplain surfaces. Multiple smaller floods within a WY that exceed the 0.995 and 0.50 AEPs (such as in WY 1996) can transport as much or more bed-material sediment than a single, higher magnitude event (such as the maximum event recorded in WY 2000 with an estimated AEP of around 0.002). Bedload transport capacity generally exceeds sediment supply (greater than 2 millimeters [mm]) for most of the study area from Wildcat Creek to the City of Siletz as evidenced by substantial in-channel bedrock. Despite overall conditions of limited sediment supply, transport capacity still varies considerably within and between years with discharge magnitude and spatially in relation to local hydraulics imposed by bedrock, channel morphology, and human infrastructure (such as bridges). Results of Objective Three, an analysis of PBH for lamprey larvae, include the following About 28 percent of the Siletz River network meets the mean annual suspended sediment loads and channel slope criteria for PBH. Along the main-stem Siletz River, in-channel bedrock outcrops and high transport capacity are expected to further constrain PBH. Together, these results suggest that most of the Siletz River between Wildcat Creek and the City of Siletz has had only modest vertical and lateral change between the 1930s and 2010s because of the bedrock in and along the main channel and the river’s relatively high transport capacity relative to bed-material sediment supply. However, localized sections of the Siletz River where the active channel widens, particularly at channel bends, exhibited some change in channel planform and the locations and area of gravel bars. In the future, moderate increases in autumn-winter discharge may not result in substantial changes in coarse gravel bars along the Siletz River but may result in selective transport of finer bed-material sediment (gravel, sands, and silts) that provide spawning habitats for Chinook salmon and Pacific lamprey and burrowing habitats for lamprey larvae. Assuming no substantial changes in bed-material sediment supply, increased bedload transport capacity may cause frequent entrainment of lamprey larvae that are burrowed in coarse sand deposits, suspension and downstream transport of salmon eggs incubating in gravels, and reductions in the areas of spawning gravels for Chinook salmon and Pacific lamprey. Exact implications of current and future discharge conditions for these species along the Siletz River depends on many factors, including sediment supply, local hydraulics, and the timing of flood events relative to fish life stages.

Oregon↗
USGS2000

Hydrology and water and sediment quality at James Campbell National Wildlife Refuge near Kahuku, Island of Oahu, Hawaii

The James Campbell National Wildlife Refuge occupies two lowland marsh and pond complexes on the northern coastal plain of Oahu: the mostly natural ponds and wetlands of the Punamano Unit and the constructed ponds of the Kii Unit. The U.S. Fish and Wildlife Service manages the Refuge primarily to protect and enhance habitat for four endangered species of Hawaiian waterbirds. Kii Unit is fed by artesian wells and rainfall, whereas Punamano Unit is fed naturally by rainfall, runoff, and ground-water seepage. Streams drain from the uplands into lowland ditches that pass through Kii Unit on their way to the ocean. A high-capacity pump transfers water from the inner ditch terminus at Kii to the ocean outlet channel. Stormwaters also exit the inner ditch system over flood-relief swales near the outlet pump and through a culvert with a one-way valve. A hydrologic investigation was done from November 1996 through February 1998 to identify and quantify principal inflows and outflows of water to and from the Refuge, identify hydraulic factors affecting flooding, document ground-water/surface-water interactions, determine the adequacy of the current freshwater supply, and determine water and sediment quality. These goals were accomplished by installing and operating a network of stream-gaging stations, meteorology stations, and shallow ground-water piezometers, by computing water budgets for the two Refuge units, and by sampling and analyzing water and pond-bottom sediments for major ions, trace metals, and organic compounds. Streamflow during the study was dominated by winter stormflows, followed by a gradual recession of flow into summer 1997, as water that had been stored in alluvial fans drained to lowland ditches. Outflow at the ditch terminus in 1997 was 125 million gallons greater than measured inflow to the coastal plain, mainly reflecting gains from ground water along the ditches between outlying gages and the ditch terminus. Of the measured 1997 outflow, 98 percent was through the Kii outlet pump, with the outlet culvert valve only opening for brief periods during storms. Large volumes of stormflow overflowed the flood-relief swales unmeasured. The largest storm of the study, in November 1996, was estimated to have a flood frequency of about 3 to 4 years. Streamflow exceeded culvert capacity and overtopped Kamehameha Highway at Kalaeokahipa Stream and Hospital ditch. Slight overbank flooding in Kii ditch resulted strictly from high discharge. Minor overbank flooding farther out on the coastal plain probably was caused mainly by the small hydraulic gradients available to convey stormflows along the lowland ditches. Stormwaters flooded Kii ponds and flowed back upstream along Punamano ditch into Punamano marsh, introducing suspended sediment and possibly other contaminants to the Refuge. Two smaller storms in January 1997 resulted in smaller flows and no overbank flooding. The Kii outlet pump ran continuously for 7 days during the November 1996 storm and for 1 to 2 days during the January 1997 storms. During all three storms, the outlet culvert valve opened and the inner ditches overtopped the flood-relief swales, allowing free outflow of water from the inner ditch. Backwater effects hindered drainage during the January 1997 storms at Hospital ditch at Kamehameha Highway, and at Punamano ditch at Nudist Camp Road (where the backflow into Punamano marsh in November 1996 constituted an extreme backwater effect). A probable marine backwater effect was imposed at the ocean outlet ditch during the November 1996 storm through a combination of high spring tides and wave setup from large surf. Whether this backwater effect propagated upstream in the ditches to affect inland sites could not be determined conclusively. A sand plug may have built up in the ocean outlet channel before the November 1996 storm, but if so, it probably washed out prior to, or early in the storm, and was not present at the time of peak stage at inland sites. A season-long buildup of the sand plug in late 1997 was inferred from rising water levels in the outlet ditch. Seawater flows up the outlet channel or over the sand berm and into the outer ditch system on most high tides, and particularly during spring high tides. Ponds and ditches of the Refuge and surrounding lowlands have mud- and clay-lined bottoms that form an effective confining unit and inhibit interaction with an underlying shallow limestone aquifer. At Kii Unit, pond levels are higher than adjacent ditch levels and underlying ground-water levels, establishing lateral and downward head gradients that could foster seepage losses from the ponds. Regional ground-water discharge from the Koolau aquifer to the coastal-plain sediments is mostly diffuse, but is concentrated where ridges of Koolau Basalt plunge beneath coastal-plain sediments near Punamano Unit and at the head of Hospital ditch. Kii ditch gains brackish ground water downstream of Kamehameha Highway. Wastewater disposal from the sewage treatment plant adjoining Kii Unit poses little or no threat to Refuge habitat. Disposal is at six injection wells located 0.45 mi away at Kahuku, and the wells inject into confined limestone aquifers that do not extend to Kii Unit. The natural freshwater supply to Punamano Unit is adequate for maintaining the wildlife habitat, judging from stable pond levels and low salinities there. A monthly water budget for Punamano showed an apparent annual deficit in measurable flows in 1997, requiring unmeasured ground-water gains equalling 51 inches of water. The freshwater supply to Kii Unit is inadequate according to Refuge managers, because there is not enough water to manipulate levels adequately in the ponds during most of the year, and particularly during the driest months. This is confirmed by monthly deficits in the water budget for the Kii ponds during summer months. However, the Kii budget showed an annual surplus in measurable flows for 1997 equalling 24 inches of water. Unmeasured losses are required to explain the apparent annual surplus, such as discharge to the ditches through pond water-control structures and downward and/or lateral ground-water seepage. The apparent surplus at Kii is strictly hydrologic and is not a surplus in a management sense; it cannot be stored or used to supply the Refuge, but instead reflects losses from the system that render this amount of water unavailable for use. The budget year, 1997, was drier than normal (24 percent below long-term mean rainfall) and so the measured potential evaporation for 1997 was probably higher than the long-term mean. Few metals or organic compounds of potential concern were detected in pond and ditch waters and in pond-bottom sediments. Detected pesticides were at trace levels or just above minimum reporting limits. Exceptions that exceeded quality guidelines for freshwater sediment were copper and zinc in sediment from Kii ponds C and D, and copper in sediment from Punamano north pond. Therefore, urban and agricultural runoff probably have contributed little in the way of harmful metals or organic compounds to the Refuge, although the potential for such contribution remains from periodic flooding of the ponds by ditch stormflows. Salinity was low throughout most Refuge waters, qualifying as fresh to slightly brackish and suitable for the environmental needs of Refuge fauna. Higher salinities have been observed in ditches during past periods of sugarcane cultivation and saltwater aquaculture, however. Resumption of saltwater aquaculture could raise ditch salinities if saltwater effluents are disposed directly into the ditches, as they were in the past.

Hawaii↗