Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Chemistry and Water”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28Linked to original sources
USGS2004

Age and source of water in springs associated with the Jacksonville Thrust Fault Complex, Calhoun County, Alabama

Water from wells and springs accounts for more than 90 percent of the public water supply in Calhoun County, Alabama. Springs associated with the Jacksonville Thrust Fault Complex are used for public water supply for the cities of Anniston and Jacksonville. The largest ground-water supply is Coldwater Spring, the primary source of water for Anniston, Alabama. The average discharge of Coldwater Spring is about 32 million gallons per day, and the variability of discharge is about 75 percent. Water-quality samples were collected from 6 springs and 15 wells in Calhoun County from November 2001 to January 2003. The pH of the ground water typically was greater than 6.0, and specific conductance was less than 300 microsiemens per centimeter. The water chemistry was dominated by calcium, carbonate, and bicarbonate ions. The hydrogen and oxygen isotopic composition of the water samples indicates the occurrence of a low-temperature, water-rock weathering reaction known as silicate hydrolysis. The residence time of the ground water, or ground-water age, was estimated by using analysis of chlorofluorocarbon, sulfur hexafluoride, and regression modeling. Estimated ground-water ages ranged from less than 10 to approximately 40 years, with a median age of about 18 years. The Spearman rho test was used to identify statistically significant covariance among selected physical properties and constituents in the ground water. The alkalinity, specific conductance, and dissolved solids increased as age increased; these correlations reflect common changes in ground-water quality that occur with increasing residence time and support the accuracy of the age estimates. The concentration of sodium and chloride increased as age increased; the correlation of these constituents is interpreted to indicate natural sources for chloride and sodium. The concentration of silica increased as the concentration of potassium increased; this correlation, in addition to the isotopic data, is evidence that silicate hydrolysis of clay minerals occurred. The geochemical modeling program NETPATH was used to investigate possible mixing scenarios that could yield the chemical composition of water collected from springs associated with the Jacksonville Thrust Fault Complex. The results of NETPATH modeling suggest that the primary source of water in Coldwater Spring is a deep aquifer, and only small amounts of rainwater from nearby sources are discharged from the spring. Starting with Piedmont Sports Spring and moving southwest along a conceptual ground-water flow path that parallels the Jacksonville Thrust Fault Complex, NETPATH simulated the observed water quality of each spring, in succession, by mixing rainwater and water from the spring just to the northeast of the spring being modeled. The percentage of rainwater and ground water needed to simulate the quality of water flowing from the springs ranged from 1 to 25 percent rainwater and 75 to 99 percent ground water.

Scientific Investigations Report↗
USGS2007

Factors Affecting Spatial and Temporal Variability in Nutrient and Pesticide Concentrations in the Surficial Aquifer on the Delmarva Peninsula

Water quality in the unconfined, unconsolidated surficial aquifer on the Delmarva Peninsula is influenced by the availability of soluble ions from natural and human sources, and by geochemical factors that affect the mobility and fate of these ions within the aquifer. Ground-water samples were collected from 60 wells completed in the surficial aquifer of the peninsula in 2001 and analyzed for major ions, nutrients, and selected pesticides and degradation products. Analytical results were compared to similar data from a subset of sampled wells in 1988, as well as to land use, soils, geology, depth, and other potential explanatory variables to demonstrate the effects of natural and human factors on water quality in the unconfined surficial aquifer. This study was conducted as part of the National Water-Quality Assessment Program of the U.S. Geological Survey, which is designed (in part) to describe the status and trends in ground-water quality and to provide an understanding of natural and human factors that affect ground-water chemistry in different parts of the United States. Results of this study may be useful for water-resources managers tasked with addressing water-quality issues of local and regional importance because the surficial aquifer on the Delmarva Peninsula is a major source of water for domestic and public supply and provides the majority of flow in local streams. Human impacts are apparent in ground-water quality throughout the surficial aquifer. The surficial aquifer on the Delmarva Peninsula is generally sandy and very permeable with well-oxygenated ground water. Dissolved constituents found throughout various depths of the unconfined aquifer are likely derived from the predominantly agricultural practices on the peninsula, although effects of road salt, mineral dissolution, and other natural and human influences are also apparent in some areas. Nitrate occurred at concentrations exceeding natural levels in many areas, and commonly exceeded 10 milligrams per liter (as nitrogen). In addition to land use in the aquifer recharge area, concentrations of nitrate in ground water are related to regional patterns in soil drainage that affect underlying aquifer redox conditions. Over the peninsula, nitrate concentrations are not related to recharge date of the water, but are positively correlated with depth in shallow wells screened beneath agricultural areas. Nitrate concentrations increased in oxic areas (dissolved oxygen greater than 1 milligram per liter) of the deeper part of the surficial aquifer used for domestic supply by an average of about 2 milligrams per liter between 1988 and 2001, although no changes were apparent in shallower parts of the aquifer over that same period. Water in the surficial aquifer generally flows from land-surface recharge to surface-water discharge areas in less than 30 years. As a result, the entire flow system in the surficial aquifer has likely been affected by human activities on and near the land surface over the past several decades. Pesticide compounds occurred widely at low levels throughout the surficial aquifer. The most commonly used herbicides (metolachlor, alachlor, and atrazine) were the most commonly detected. These pesticides primarily occurred in ground water in the form of degradation products. The widespread occurrence of these and other pesticide compounds reflects their abundant use as well as chemical properties and aquifer characteristics that allow their movement into ground water. Mixtures of pesticides are common. Most samples contained at least 3 different compounds; several samples contained as many as 11. Pesticide concentrations in the surficial aquifer are relatively high beneath recharge areas with well-drained soils in the shallow part of the aquifer and in oxic environments throughout the surficial aquifer. Concentrations are generally below existing drinking-water standards, although standards are not available for all of the pesticide compound

Scientific Investigations Report↗
USGS2010

Characterization of water quality and biological communities, Fish Creek, Teton County, Wyoming, 2007-08

Fish Creek, a tributary to the Snake River, is about 25 river kilometers long and is located in Teton County in western Wyoming near the town of Wilson. Public concern about nuisance growths of aquatic plants in Fish Creek have been increasing in recent years. To address this concern, the U.S. Geological Survey conducted a study in cooperation with the Teton Conservation District to characterize the water quality and biological communities in Fish Creek. Water-quality samples were collected for analyses of physical properties and water chemistry (nutrients, nitrate isotopes, and wastewater chemicals) between March 2007 and October 2008 from seven surface-water sites and three groundwater wells. During this same period, aquatic plant and macroinvertebrate samples were collected and habitat characteristics were measured at the surface-water sites. The main objectives of this study were to (1) evaluate nutrient concentrations (that influence biological indicators of eutrophication) and potential sources of nutrients by using stable isotope analysis and other indicator chemicals (such as caffeine and disinfectants) that could provide evidence of anthropogenic sources, such as wastewater or septic tank contamination in Fish Creek and adjacent groundwater, and (2) characterize the algal, macrophyte, and macroinvertebrate communities and habitat of Fish Creek. Nitrate was the dominant species of dissolved nitrogen present in all samples and was the only bioavailable species detected at concentrations greater than the laboratory reporting level in all surface-water samples. Average concentrations of dissolved nitrate in surface water were largest in samples collected from the two sites with seasonal flow near Teton Village and decreased downstream; the smallest concentration was at downstream site A-Wck. Concentrations of dissolved nitrate in groundwater were consistently greater than concentrations in corresponding surface-water sites during the same sampling event. Orthophosphate was the primary dissolved species of phosphorus present in all surface-water and groundwater samples. The average concentration of dissolved orthophosphate in surface water was largest in samples collected from near Teton Village; samples from all other sites had similar average concentrations. Concentrations of dissolved orthophosphate in groundwater also were typically greater than concentrations in corresponding surface-water sites during the same sampling event. The aquatic plant communities in Fish Creek typically were composed of a mixture of macrophytes, macroalgae, microalgae, and moss. The composition of the aquatic plant community in Fish Creek appeared to shift in the downstream direction in 2007. On average, the proportion of macrophytes ranged from about 1 percent at site A-R1U, the most upstream site, to 54 percent of the plant community at site A-R6D, the farthest downstream site sampled during 2007. The downstream increase in macrophytes was accompanied by a downstream decrease in microalgae. The average proportion of microalgae ranged from 80 percent at site A-R1U to 24 percent at site A-R6D. The proportion of the macroalgae Cladophora in the aquatic plant community was relatively high at sites A-Wck and A-R3D in both 2007 and 2008.

Scientific Investigations Report↗
USGS1976

Chemical quality of ground water in the Tehama-Colusa Canal service area, Sacramento Valley, California

The Tehama-Colusa Canal Service Area consists of about 450 square miles of irrigable land located on the west side of the Sacramento Valley, Calif. Upon the completion of the Tehama-Colusa Canal, it is expected that most of the service area will switch from passive forms of agriculture (dry farming and grazing) to intensive irrigated farming. Importation and application of surface water may affect the chemical quality of native ground water. This study documents the chemical quality of native ground water before large-scale importation and application of surface water provide the potential of altering the ground-water chemistry. Analyses of samples from 222 wells show that most of the area is underlain by ground water of a quality suitable for most agricultural and domestic uses. In the vicinities of College City-Arbuckle and the city of Williams, boron, chloride, sodium, and dissolved solids may be a threat to future agricultural activities where boron- or chloride-sensitive crops would be grown. The source of degraded ground water in the two areas is local intermittent streams that drain areas having numerous saline springs and seeps. (Woodard-USGS)

California↗
USGS1998

Estimated predevelopment discharge to streams from the High Plains Aquifer in northwestern Oklahoma, southwestern Kansas, and northwestern Texas

A study of the High Plains aquifer in Okla homa was initiated in 1996 to: (1) provide the information needed by the Oklahoma Water Resources Board to manage the quantity of water produced from the aquifer; and (2) provide base line water-chemistry data. The approach used to meet the first objective is to develop a digital ground-water flow model. The model will be cali brated, in part, by comparing simulated and esti mated predevelopment discharge from the aquifer to streams and cross-boundary flow. This report presents the estimated predevelopment discharge to streams from the High Plains aquifer. Streamflow data were the primary source of information used to estimate predevelopment dis charge from the High Plains aquifer. Data from 30 streamflow stations between the Arkansas and Canadian Rivers were considered in the analysis, and winter low-flow frequencies for 7-, 14-, and 30-day periods were determined for 25 stations. The 14-day low flow with a recurrence interval of 2 years was the primary value used to estimate pre development discharge from the aquifer. The streams that drain the eastern part of the High Plains aquifer in Kansas (generally east of 99.5 longitude) are estimated to have had large predevelopment discharge from the aquifer, and most of them received discharge from near their headwaters. For streams with more than one streamflow gage, the upper perennial reaches appeared to have gained more discharge from the aquifer than the lower reaches. The total predevel opment discharge from the aquifer in this area to several streams is estimated to have been about 312 cubic feet per second, not including discharge that probably went directly to the Arkansas River. The Cimarron River and its tributaries are estimated to have gained about 78 cubic feet per second, but nearly one-half that amount was lost in the lower reaches of the river. The cause of the loss in the lower reaches is unknown. The Beaver River and its tributaries are estimated to have gained a net of about 10 cubic feet per second above Wolf Creek with the upper reaches gaining more than the lower reaches. Wolf Creek is estimated to have gained 30 cubic feet per second over its total length.

Water-Resources Investigations Report↗
USGS2017

The response of soil and stream chemistry to decreases in acid deposition in the Catskill Mountains, New York, USA

The Catskill Mountains have been adversely impacted by decades of acid deposition, however, since the early 1990s, levels have decreased sharply as a result of decreases in emissions of sulfur dioxide and nitrogen oxides. This study examines trends in acid deposition, stream-water chemistry, and soil chemistry in the southeastern Catskill Mountains. We measured significant reductions in acid deposition and improvement in stream-water quality in 5 streams included in this study from 1992 to 2014. The largest, most significant trends were for sulfate (SO 4 2− ) concentrations (mean trend of −2.5 μeq L −1 yr −1 ); hydrogen ion (H + ) and inorganic monomeric aluminum (Al im ) also decreased significantly (mean trends of −0.3 μeq L −1 yr −1 for H + and −0.1 μeq L −1 yr −1 for Al im for the 3 most acidic sites). Acid neutralizing capacity (ANC) increased by a mean of 0.65 μeq L −1 yr −1 for all 5 sites, which was 4 fold less than the decrease in SO 4 2− concentrations. These upward trends in ANC were limited by coincident decreases in base cations (−1.3 μeq L −1 yr −1 for calcium + magnesium). No significant trends were detected in stream-water nitrate (NO 3 − ) concentrations despite significant decreasing trends in NO 3 − wet deposition. We measured no recovery in soil chemistry which we attributed to an initially low soil buffering capacity that has been further depleted by decades of acid deposition. Tightly coupled decreasing trends in stream-water silicon (Si) (−0.2 μeq L −1 yr −1 ) and base cations suggest a decrease in the soil mineral weathering rate. We hypothesize that a decrease in the ionic strength of soil water and shallow groundwater may be the principal driver of this apparent decrease in the weathering rate. A decreasing weathering rate would help to explain the slow recovery of stream pH and ANC as well as that of soil base cations.

New York↗
USGS2026

Streamflow, water quality, and energy development characteristics and water-quality trends for selected sites in the Green River and Muddy Creek drainage basins, southwestern Wyoming, water years 2006–16

Energy resource development in southwestern Wyoming has been rapidly expanding since the early 2000s to include innovative technologies for extracting oil and gas and enhancing renewable energy. In response to concerns about the potential negative effects of energy development on natural resources, the Wyoming Landscape Conservation Initiative was created to implement a long-term, science-based program of assessing, conserving, and enhancing fish and wildlife habitats while facilitating responsible energy development through local collaborations and partnerships. The U.S. Geological Survey, in cooperation with the Bureau of Land Management, began monitoring streamflow and water quality as part of this initiative in 2006 at four U.S. Geological Survey streamgages within the Green River and Muddy Creek drainage basins to characterize the effects of energy development on streamflow and water quality in these areas. To quantify changes in water quality metrics, trend analyses for the 2006–16 water years were calculated and related to drainage basin characteristics including energy development (wells per square mile). Effects of energy development on water quality varied by watershed and the variability was driven primarily by the runoff efficiency and the geochemistry of the drainage basin. The New Fork River water chemistry was a calcium-bicarbonate type with low ionic strength and showed no statistically significant trends in water quality despite increased energy development. The Green River experienced moderate energy development, with significant upward trends in magnesium and alkalinity, indicating low sensitivity to development. Muddy Creek near Dad had minimal energy development and complex hydrogeochemical characteristics, showing mixed trends in water quality constituents. Muddy Creek near Baggs experienced moderate energy development, with significant upward trends in several water quality indicators indicating a response to the land disturbance associated with development. Overall, geochemistry and runoff efficiency influenced the vulnerability of water quality to energy development activities, highlighting the importance of drainage basin physical characteristics on vulnerability to development.

Scientific Investigations Report↗
USGS1999

Environmental setting and natural factors and human influences affecting water quality in the White River Basin, Indiana

The White River Basin drains 11,349 square miles of central and southern Indiana and is one of 59 Study Units selected for water-quality assessment as part of the U.S. Geological Survey's National WaterQuality Assessment Program. Defining the environmental setting of the basin and identifying the natural factors and human influences that affect water quality are important parts of the assessment. Interrelated natural factors help determine the quality of surface and ground water in a river basin. The White River Basin has a humid continental climate, characterized by well-defined winter and summer seasons. Geologic features in the basin include glaciated and nonglaciated areas; a region of karst geomorphology that is characterized by caves and sinkholes; and a thick, sedimentary bedrock sequence underlying the entire basin. Unconsolidated glacial deposits of clay, silt, sand and gravel cover more than 60 percent of the basin. Soils developed in unconsolidated glacial deposits are typically fertile, naturally or artificially well drained, and farmed. Soils in the unglaciated south-central part of the basin are thin, have low fertility, and are best suited for forest or pasture. Agriculture is the principal land use in the White River Basin. Approximately 70 percent of the basin is used for agriculture, and about 50 percent of the basin is cropland. Corn and soybeans are the major crops. Other significant land uses are forest (22 percent) and urban and residential (7 percent). The population of the basin was 2.1 million in 1990. Water use in the White River Basin totaled 1,284 million gallons per day in 1995, of which 84.5 percent was surface water and 15.5 percent was ground water. Despite the predominant use of surface water, ground water was the primary source of drinking water for approximately 56 percent of the population. The general water chemistry in the White River Basin is determined by natural factors such as soils and geologic materials that water contacts as it moves through the hydrologic system. In the southern part of the basin, bedrock upland areas are dominated by non-carbonate bedrock, thin soils, and high runoff-rainfall ratios. These areas have small chemical concentrations in streamwater. Conversely, in the northern part of the basin where glacial deposits are thick and in the southwestern part of the basin where loess deposits are thick, water has longer periods of time to react with soils and aquifers and to acquire substantial quantities of dissolved constituents. As a result, streams in the till plain and glacial lowland have higher concentrations of most constituents than streams in the unglaciated parts of the basin. Water quality is significantly modified by human influences. Water quality is affected locally by point sources of contamination that include combined-sewer overflows, power-generation-plant cooling stations, and wastewater-treatment-plant effluents that are generally associated with densely populated areas. Water quality is additionally affected by non-point sources of contamination related to agriculture, urban runoff, and mining. Six hydrogeomorphic regions of the White River Basin are delineated on the basis of distinct and relatively homogeneous natural characteristics. These six regions are used in the White River Basin study as a framework for examining the effects of natural factors on water quality in the basin. Bedrock is exposed or near the surface in three hydrogeomorphic regions the bedrock uplands, bedrock lowland and plain, and karst plain; streams and shallow aquifers in these regions are susceptible to contamination, especially in the karst plain, and show rapid response to rainfall. The other three hydrogeomorphic regions the fluvial deposits, till plain, and glacial lowland are in the glaciated part of the basin. Where thick fine-grained unconsolidated sediments are present, primarily in the till plain, ground-water supplies are protected from contamination, and extreme high and low streamflows are moderated.

Indiana↗
USGS2022

Hydrogeology and groundwater quality in the San Agustin Basin, New Mexico, 1975–2019

This report describes the findings of a U.S. Geological Survey study, completed in cooperation with the Bureau of Land Management, focused on better understanding the present-day (1975–2019) hydrogeology and groundwater quality of the San Agustin Basin in west-central New Mexico to support sustainable groundwater resource management. The basin hosts a relatively undeveloped basin-fill and alluvium aquifer system and is topographically divided into east and west subbasins by the McClure Hills. Groundwater chemistry and groundwater elevation data were compiled, collected, and interpreted in the context of groundwater flow and quality. The analyses presented in this report consider groundwater chemistry data collected within the last decade (2010–19) and groundwater elevation data collected from 1975 through 2019 to provide insight into present-day conditions. Groundwater elevations show that groundwater typically moves from the highlands to the lowlands, with a prominent east to west regional trend. Groundwater elevations were lowest in the southwestern portion of the west subbasin, where estimated flow directions suggest underflow through the local highlands into the northern East Fork Gila River watershed, which is further supported by historical groundwater elevation data from the northern East Fork Gila River watershed. Gradual groundwater elevation gradients (about 2 feet per mile) near the east and west subbasin divide suggest that groundwater slowly flows from the east subbasin to the west subbasin. Quantitative analyses of groundwater chemistry data show that groundwater in both subbasins has similar chemical characteristics. A systematic east to west groundwater evolution in water chemistry was not observed despite evidenced subbasin connectivity. The absence of this pattern suggests that groundwater mixing is regionally prevalent, sediment reactivity is low and variable, and (or) recharge conditions are comparable in both subbasins. Groundwater chemistry was generally independent of aquifer type, suggesting that the aquifers are hydrologically well connected. Corrected carbon-14 groundwater age estimates in the basin ranged from 232 to 13,916 years before present with a median of 5,409 years. A wide range of groundwater ages is therefore present in the basin, with waters commonly being thousands of years old, thereby supporting generally slow regional groundwater movement. A component of relatively young groundwater, for which estimated ages could not be accurately computed, is also present in the basin, and it may commonly mix with older waters. The spatial distribution of categorical and quantitative groundwater ages indicates that most recharge likely occurs in the highlands through mountain-block recharge and as focused recharge within arroyos, although evidence of modern (1953 and after) groundwater was minimal at sampled sites. Median annual gradients (groundwater elevation change over time) indicate that most groundwater elevations in the lowlands changed little (−0.2 to 0.2 foot per year) from 1975 through 2019. Groundwater elevations in the highlands varied more annually, which is likely due to recharge from precipitation events. These more variable groundwater elevations in the highlands compared with the lowlands, along with groundwater ages, provide further evidence that most groundwater recharge takes place in the highlands, with minimal recharge in the lowlands. Median groundwater elevation change for all sites was −0.05 foot per year. Temporal consistency of lowland groundwater elevations suggests that regional groundwater dynamics have been more or less stable through time under current climate and development conditions, although median annual gradients indicate that groundwater elevations may have slightly declined on average between 1975 and 2019.

New Mexico↗
USGS2014

Relationships between water and gas chemistry in mature coalbed methane reservoirs of the Black Warrior Basin

Water and gas chemistry in coalbed methane reservoirs of the Black Warrior Basin reflects a complex interplay among burial processes, basin hydrodynamics, thermogenesis, and late-stage microbial methanogenesis. These factors are all important considerations for developing production and water management strategies. Produced water ranges from nearly potable sodium-bicarbonate water to hypersaline sodium-chloride brine. The hydrodynamic framework of the basin is dominated by structurally controlled fresh-water plumes that formed by meteoric recharge along the southeastern margin of the basin. The produced water contains significant quantities of hydrocarbons and nitrogen compounds, and the produced gas appears to be of mixed thermogenic-biogenic origin. Late-stage microbial methanogenesis began following unroofing of the basin, and stable isotopes in the produced gas and in mineral cements indicate that late-stage methanogenesis occurred along a CO 2 -reduction metabolic pathway. Hydrocarbons, as well as small amounts of nitrate in the formation water, probably helped nourish the microbial consortia, which were apparently active in fresh to hypersaline water. The produced water contains NH 4 + and NH 3 , which correlate strongly with brine concentration and are interpreted to be derived from silicate minerals. Denitrification reactions may have generated some N 2 , which is the only major impurity in the coalbed gas. Carbon dioxide is a minor component of the produced gas, but significant quantities are dissolved in the formation water. Degradation of organic compounds, augmented by deionization of NH 4 + , may have been the principal sources of hydrogen facilitating late-stage CO 2 reduction.

Alabama↗
USGS2025

Groundwater salinity: Applying the specific conductance and water type proxy

Groundwater is increasingly needed for water supplies but may have limited utility in some locations because of its salinity. Salinity, often expressed as total dissolved solid (TDS), is frequently estimated using specific conductance (SC) measurements. However, the commonly used proxy (0.65 multiplied by SC to indicate TDS, common in many handheld meters) can result in inaccurate TDS estimates. First, the TDS–SC relationship is not linear over the entire concentration range of groundwater. Furthermore, the TDS (and salinity)–SC relationships vary substantially depending on the major-ion composition. Here we develop a proxy method utilizing SC and major-ion water type to estimate TDS and salinity specifically for groundwaters. Compared to most surface waters, groundwater tends to have a wider range of salinity (fresh to highly saline) and higher concentrations of bedrock-derived solutes such as carbonate ions, silica, and many other ions. The dataset used to develop the proxies includes water chemistry data from 149,059 discrete groundwater samples. The groundwater proxies, which employ nonlinear log–log relations, utilize five water types (HCO 3 , Cl, Ca-Mg-SO 4 , Na-K-SO 4 , and mixed waters), are accurate (median percent difference between TDS and salinity determined using the proxy compared to discrete measurements was <±0.8%) over a wide range of SC (up to 200 mS/cm), rapid, cost-effective, and can be measured on-site.

Groundwater↗
USGS2009

The use of fluoride as a natural tracer in water and the relationship to geological features: Examples from the Animas River Watershed, San Juan Mountains, Silverton, Colorado

Investigations within the Silverton caldera, in southwestern Colorado, used a combination of traditional geological mapping, alteration-assemblage mapping, and aqueous geochemical sampling that showed a relationship between geological and hydrologic features that may be used to better understand the provenance and evolution of the water. Veins containing fluorite, huebnerite, and elevated molybdenum concentrations are temporally and perhaps genetically associated with the emplacement of high-silica rhyolite intrusions. Both the rhyolites and the fluorite-bearing veins produce waters containing elevated concentrations of F - , K and Be. The identification of water samples with elevated F/Cl molar ratios (> 10) has also aided in the location of water draining F-rich sources, even after these waters have been diluted substantially. These unique aqueous geochemical signatures can be used to relate water chemistry to key geological features and mineralized source areas. Two examples that illustrate this relationship are: (1) surface-water samples containing elevated F - concentrations (> 1.8 mg/l) that closely bracket the extent of several small high-silica rhyolite intrusions; and (2) water samples containing elevated concentrations of F - (> 1.8 mg/ l) that spatially relate to mines or areas that contain late-stage fluorite/huebnerite veins. In two additional cases, the existence of high F - concentrations in water can be used to: (1) infer interaction of the water with mine waste derived from systems known to contain the fluorite/huebnerite association; and (2) relate changes in water quality over time at a high elevation mine tunnel to plugging of a lower elevation mine tunnel and the subsequent rise of the water table into mineralized areas containing fluorite/huebnerite veining. Thus, the unique geochemical signature of the water produced from fluorite veins indicates the location of high-silica rhyolites, mines, and mine waste containing the veins. Existence of high F - concentrations along with K and Be in water in combination with other geological evidence may be used to better understand the provenance of the water. ?? 2009 AAG/Geological Society of London.

Colorado↗
USGS2009

Brine migration from a flooded salt mine in the Genesee Valley, Livingston County, New York: Geochemical modeling and simulation of variable-density flow

The Retsof salt mine in upstate New York was flooded from 1994 to 1996 after two roof collapses created rubble chimneys in overlying bedrock that intersected a confined aquifer in glacial sediments. The mine now contains about 60 billion liters of saturated halite brine that is slowly being displaced as the weight of overlying sediments causes the mine cavity to close, a process that could last several hundred years. Saline water was detected in the confined aquifer in 2002, and a brine-mitigation project that includes pumping followed by onsite desalination was implemented in 2006 to prevent further migration of saline water from the collapse area. A study was conducted by the U.S. Geological Survey using geochemical and variable-density flow modeling to determine sources of salinity in the confined aquifer and to assess (1) processes that control movement and mixing of waters in the collapse area, (2) the effect of pumping on salinity, and (3) the potential for anhydrite dissolution and subsequent land subsidence resulting from mixing of waters induced by pumping. The primary source of salinity in the collapse area is halite brine that was displaced from the flooded mine and transported upward by advection and dispersion through the rubble chimneys and surrounding deformation zone. Geochemical and variable-density modeling indicate that salinity in the upper part of the collapse area is partly derived from inflow of saline water from bedrock fracture zones during water-level recovery (January 1996 through August 2006). The lateral diversion of brine into bedrock fracture zones promoted the upward migration of mine water through mixing with lower density waters. The relative contributions of mine water, bedrock water, and aquifer water to the observed salinity profile within the collapse area are controlled by the rates of flow to and from bedrock fracture zones. Variable-density simulations of water-level recovery indicate that saline water has probably not migrated beyond the collapse area, while simulations of pumping indicate that further upward migration of brine and saline water is now prevented by groundwater withdrawals under the brine-mitigation project. Geochemical modeling indicates that additional land subsidence as a result of anhydrite dissolution in the collapse area is not a concern, as long as the rate of brine pumping is less than the rate of upward flow of brine from the flooded mine. The collapse area above the flooded salt mine is within a glacially scoured bedrock valley that is filled with more than 150 meters of glacial drift. A confined aquifer at the bottom of the glacial sediments (referred to as the lower confined aquifer, or LCA) was the source of most of the water that flooded the mine. Two rubble chimneys that formed above the roof collapses in 1994 hydraulically connect the flooded mine to the LCA through 180 meters of sedimentary rock. From 1996 through 2006, water levels in the aquifer system recovered and the brine-displacement rate ranged from 4.4 to 1.6 liters per second, as estimated from land-surface subsidence above the mine. A zone of fracturing within the bedrock (the deformation zone) formed around the rubble chimneys as rock layers sagged toward the mine cavity after the roof collapses. Borehole geophysical surveys have identified three saline-water-bearing fracture zones in the bedrock: at stratigraphic contacts between the Onondaga and Bertie Limestones (O/B-FZ) and the Bertie Limestone and the Camillus Shale (B/C-FZ), and in the Syracuse Formation (Syr-FZ). The only outlets for brine displaced from the mine are through the rubble chimneys, but some of the brine could be diverted laterally into fracture zones in the rocks that lie between the mine and the LCA. Inverse geochemical models developed using PHREEQC indicate that halite brine in the flooded mine is derived from a mixture of freshwater from the LCA (81 percent), saline water from bedrock fracture zones (16 percent), and an hypothesized bromide-rich brine (3 percent) assumed to originate from salt-bearing rocks above the flooded mine. Geochemical modeling results also indicate that halite brine entering the rubble chimneys is diluted by both bedrock water and aquifer water, and that water from the mine has not reached the bedrock surface. Forward geochemical models indicate that additional land subsidence could occur if pumping from the brine-mitigation project were to introduce either freshwater or bedrock water that is undersaturated with respect to anhydrite into the lower part of the rubble chimneys. In this unlikely scenario, the maximum subsidence rates are predicted to range from 0.6 to 1.1 centimeters per year—subsidence rates would be lower (0.1 to 0.6 centimeters per year) if ion-exchange reactions affect the water chemistry. Variable-density, transient groundwater-flow models were constructed using SEAWAT to simulate the movement of saline water, aquifer water, bedrock water, and brine within the rubble chimneys and surrounding deformation zone during the 10.7-year period following flooding of the salt mine. Two three-dimensional models reproduced the profile of halite saturation with depth measured in September 2006 reasonably well, and neither model indicated that saline water had migrated beyond the collapse area. The models differed in the number of fracture zones represented: one zone in model A (O/B-FZ) and three zones in model B (O/B-FZ, B/C-FZ, and Syr-FZ). It is unknown whether model A or model B better represents current conditions because the lateral extents of the B/C-FZ and Syr-FZ have not been delineated beyond the collapse area. In model A, the salinity of water in the upper part of the rubble chimneys is derived mainly from the inflow of bedrock water from the O/B-FZ, as indicated by geochemical models. Bedrock water that was pushed upward by brine during the 10.7-year simulation period formed a diffuse front above a nearly horizontal brine level in both chimneys. In model B, some of the salinity in the upper part of the rubble chimneys is derived from mine water. The rate of bedrock-water inflow from the O/B-FZ was lower in model B than in model A, and mixing with waters from the Syr-FZ and B/C-FZ transported mine water higher in the water column than in model A. Simulated brine levels in both chimneys sloped northward, reflecting lateral diversion of brine into the B/C-FZ, and less aquifer water was displaced from the collapse area than in model A. Models A and B were used to simulate changes in water levels and salinity produced by pumping for the brine-mitigation project from September 2006 through February 2008. Both simulations indicated that current pumping rates are sufficient to offset upward migration of brine and saline water through the collapse area and, therefore, to further prevent contamination of the LCA. A greater decrease in salinity was simulated in model B, however, because the porosity of the rubble chimneys was lower (6 percent compared to 10 percent in model A), and some brine and saline waters were diverted through the B/C-FZ. Model B better simulates the influent saturation to the desalination plant, the amount of halite produced, and the observed declines in saturations than model A, which is more consistent with results of geochemical modeling. Sensitivity analyses indicate that the actual brine-displacement rate could be lower than estimated because simulated declines in saturations underpredict the observed decline from September 2006 through February 2008. Although halite saturations within the upper part of the collapse area are predicted to decrease with continued pumping, brine displacement from the flooded mine is expected to continue for hundreds of years. Simulations of a shutdown of the brine-mitigation project indicate southward migration of saline water through the LCA, extending 700 meters to the model boundary within 10 years. Continued migration of saline water would eventually form a pool in the LCA in a bedrock depression 8 kilometers south of the collapse area near Sonyea, but the large relative density of the saline water would likely prevent it from reaching overlying aquifers. Simulations also indicate that brine will migrate through bedrock fracture zones—some brine could possibly emerge updip to the north where the subcrop area of the Bertie Limestone intersects the bedrock surface near Avon, but the projected time of travel is unknown.

New York↗
USGS2009

Simulation of Water Quality in the Tull Creek and West Neck Creek Watersheds, Currituck Sound Basin, North Carolina and Virginia

A study of the Currituck Sound was initiated in 2005 to evaluate the water chemistry of the Sound and assess the effectiveness of management strategies. As part of this study, the Soil and Water Assessment Tool (SWAT) model was used to simulate current sediment and nutrient loadings for two distinct watersheds in the Currituck Sound basin and to determine the consequences of different water-quality management scenarios. The watersheds studied were (1) Tull Creek watershed, which has extensive row-crop cultivation and artificial drainage, and (2) West Neck Creek watershed, which drains urban areas in and around Virginia Beach, Virginia. The model simulated monthly streamflows with Nash-Sutcliffe model efficiency coefficients of 0.83 and 0.76 for Tull Creek and West Neck Creek, respectively. The daily sediment concentration coefficient of determination was 0.19 for Tull Creek and 0.36 for West Neck Creek. The coefficient of determination for total nitrogen was 0.26 for both watersheds and for dissolved phosphorus was 0.4 for Tull Creek and 0.03 for West Neck Creek. The model was used to estimate current (2006-2007) sediment and nutrient yields for the two watersheds. Total suspended-solids yield was 56 percent lower in the urban watershed than in the agricultural watershed. Total nitrogen export was 45 percent lower, and total phosphorus was 43 percent lower in the urban watershed than in the agricultural watershed. A management scenario with filter strips bordering the main channels was simulated for Tull Creek. The Soil and Water Assessment Tool model estimated a total suspended-solids yield reduction of 54 percent and total nitrogen and total phosphorus reductions of 21 percent and 29 percent, respectively, for the Tull Creek watershed.

North Carolina, Virginia↗
USGS2024

Water resources inventory of the Las Cienegas National Conservation Area, southeastern Arizona

The Las Cienegas National Conservation Area was established by the Las Cienegas National Conservation Area Establishment Act of 1999 (Public Law 106–538) and is managed by the Bureau of Land Management. Located in southeastern Arizona, the conservation area contains more than 45,000 acres of rolling grassland, wetlands, and woodlands surrounded by isolated mountain ranges that are part of the Madrean archipelago. This report describes the surface-water and groundwater resources within, and hydrologically connected to, the conservation area. Two primary aquifers have been identified within the Las Cienegas National Conservation Area: a Quaternary alluvial aquifer and a Miocene to Pliocene basin-fill aquifer. The Quaternary alluvial aquifer consists of Quaternary saturated stream alluvium along Cienega Creek and its major tributaries. This aquifer provides the water necessary for base flow in the perennial stream reaches that support aquatic life and for wetland and riparian habitat along the stream courses. Wells and piezometers completed in the Quaternary alluvial aquifer show both seasonal and daily water-level fluctuation patterns, as well as responses to flood flows in Cienega Creek. The basin-fill aquifer, in contrast, consists chiefly of Miocene to Pliocene alluvium within a sedimentary basin that is at least 4,800 feet deep. This aquifer is developed for anthropogenic uses more often than the Quaternary alluvial aquifer is developed. Generally, water levels in wells completed in the basin-fill aquifer have gradually declined a few feet between 2011, when measurements began, and 2022, when this report was written. Most water-chemistry samples available from the basin-fill aquifer had either a sodium-bicarbonate or calcium-bicarbonate water type. Previous research has shown that most recharge to the basin-fill aquifer likely comes from mountain-front and mountain-block recharge. Research further shows that this aquifer likely provides most of the recharge to the Quaternary alluvial aquifer. Because no production wells completed in bedrock exist within the conservation area, little is known about the hydraulic properties of the bedrock therein, but usable quantities of water can likely be produced from places where the bedrock has highly developed joint or fracture systems. During 2006–2021, the average combined length of measured perennial stream reaches within the main part of the Las Cienegas National Conservation Area was 6.35 miles. The average annual base flow of Cienega Creek during 2002–2021, estimated with the Standard Base-Flow Index method using data from a streamgage within the conservation area, was 0.62 cubic feet per second. Monthly mean streamflow measured at this streamgage for the same period ranged from a low of 0.29 cubic feet per second (in June) to a high of 9.8 cubic feet per second (in July). The July average is heavily influenced by a flood that occurred in July 2021; the median July streamflow for 2002–2021 is just 0.84 cubic feet per second. Periods with no daily flow are not uncommon at this gage during late May and June.

Arizona↗
USGS2016

Completion summary for boreholes TAN-2271 and TAN‑2272 at Test Area North, Idaho National Laboratory, Idaho

In 2015, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, drilled and constructed boreholes TAN-2271 and TAN-2272 for stratigraphic framework analyses and long-term groundwater monitoring of the eastern Snake River Plain aquifer at the Idaho National Laboratory in southeast Idaho. Borehole TAN-2271 initially was cored to collect continuous geologic data, and then re-drilled to complete construction as a monitor well. Borehole TAN-2272 was partially cored between 210 and 282 feet (ft) below land surface (BLS) then drilled and constructed as a monitor well. Boreholes TAN-2271 and TAN-2272 are separated by about 63 ft and have similar geologic layers and hydrologic characteristics based on geologic, geophysical, and aquifer test data collected. The final construction for boreholes TAN-2271 and TAN-2272 required 10-inch (in.) diameter carbon-steel well casing and 9.9-in. diameter open-hole completion below the casing to total depths of 282 and 287 ft BLS, respectively. Depth to water is measured near 228 ft BLS in both boreholes. Following construction and data collection, temporary submersible pumps and water-level access lines were placed to allow for aquifer testing, for collecting periodic water samples, and for measuring water levels. Borehole TAN-2271 was cored continuously, starting at the first basalt contact (about 33 ft BLS) to a depth of 284 ft BLS. Excluding surface sediment, recovery of basalt and sediment core at borehole TAN-2271 was better than 98 percent. Based on visual inspection of core and geophysical data, material examined from 33 to 211ft BLS primarily consists of two massive basalt flows that are about 78 and 50 ft in thickness and three sediment layers near 122, 197, and 201 ft BLS. Between 211 and 284 ft BLS, geophysical data and core material suggest a high occurrence of fractured and vesicular basalt. For the section of aquifer tested, there are two primary fractured aquifer intervals: the first between 235 and 255 ft BLS and the second between 272 and 282 ft BLS. Basalt texture for borehole TAN-2271 generally was described as aphanitic, phaneritic, and porphyritic. Sediment layers, starting near 122 ft BLS, generally were composed of fine-grained sand and silt with a lesser amount of clay. Basalt flows generally ranged in thickness from 2 to 78 ft and varied from highly fractured to dense with high to low vesiculation. Geophysical data and limited core material collected from TAN-2272 show similar lithologic sequences to those reported for TAN-2271. Geophysical and borehole video logs were collected during certain stages of the drilling and construction process at boreholes TAN-2271 and TAN-2272. Geophysical logs were examined synergistically with available core material to confirm geologic and hydrologic similarities and suggest possible fractured network interconnection between boreholes TAN-2271 and TAN-2272. Natural gamma log measurements were used to assess the completeness of the vapor port lines behind 10-in. diameter well casing. Electromagnetic flow meter results were used to identify downward flow conditions that exist for boreholes TAN-2271 and TAN-2272. Furthermore, gyroscopic deviation measurements were used to measure horizontal and vertical displacement at all depths in boreholes TAN-2271 and TAN-2272. After borehole construction was completed, single‑well aquifer tests were done within wells TAN-2271 and TAN ‑ 2272 to provide estimates of transmissivity and hydraulic conductivity. The transmissivity and hydraulic conductivity were estimated for the pumping well and observation well during the aquifer tests conducted on August 25 and August 27, 2015. Estimates for transmissivity range from 4.1 . 10 3 feet squared per day (ft 2 /d) to 8.1 . 10 3 ft 2 /d; estimates for hydraulic conductivity range from 5.8 to 11.5 feet per day (ft/d). Both TAN-2271 and TAN ‑ 2272 show sustained pumping rates of about 30 gallons per minute (gal/min) with measured drawdown in the pumping well of 1.96 ft and 1.14 ft, respectively. The transmissivity estimates for wells tested were within the range of values determined from previous aquifer tests in other wells near Test Area North. Groundwater samples were collected from both wells and were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Groundwater samples for most of the inorganic constituents showed similar water chemistry in both wells. Groundwater samples for strontium-90, trichloroethene, and vinyl chloride exceeded maximum contaminant levels for public drinking water supplies in one or both wells.

Idaho↗
USGS1994

Pore-water extraction from unsaturated tuff by triaxial and one-dimensional compression methods, Nevada Test Site, Nevada

Study of the hydrologic system at Yucca Mountain, Nevada, requires the extraction of pore-water samples from welded and nonwelded, unsaturated tuffs. Two compression methods (triaxial compression and one-dimensional compression) were examined to develop a repeatable extraction technique and to investigate the effects of the extraction method on the original pore-fluid composition. A commercially available triaxial cell was modified to collect pore water expelled from tuff cores. The triaxial cell applied a maximum axial stress of 193 MPa and a maximum confining stress of 68 MPa. Results obtained from triaxial compression testing indicated that pore-water samples could be obtained from nonwelded tuff cores that had initial moisture contents as small as 13 percent (by weight of dry soil). Injection of nitrogen gas while the test core was held at the maximum axial stress caused expulsion of additional pore water and reduced the required initial moisture content from 13 to 11 percent. Experimental calculations, together with experience gained from testing moderately welded tuff cores, indicated that the triaxial cell used in this study could not apply adequate axial or confining stress to expel pore water from cores of densely welded tuffs. This concern led to the design, fabrication, and testing of a one-dimensional compression cell. The one-dimensional compression cell used in this study was constructed from hardened 4340-alloy and nickel-alloy steels and could apply a maximum axial stress of 552 MPa. The major components of the device include a corpus ring and sample sleeve to confine the sample, a piston and base platen to apply axial load, and drainage plates to transmit expelled water from the test core out of the cell. One-dimensional compression extracted pore water from nonwelded tuff cores that had initial moisture contents as small as 7.6 percent; pore water was expelled from densely welded tuff cores that had initial moisture contents as small as 7.7 percent. Injection of nitrogen gas at the maximum axial stress did not produce additional pore water from nonwelded tuff cores, but was critical to recovery of pore water from densely welded tuff cores. Gas injection reduced the required initial moisture content in welded tuff cores from 7.7 to 6.5 percent. Based on the mechanical ability of a pore-water extraction method to remove water from welded and nonwelded tuff cores, one-dimensional compression is a more effective extraction method than triaxial compression. However, because the effects that one-dimensional compression has on pore-water chemistry are not completely understood, additional testing will be needed to verify that this method is suitable for pore-water extraction from Yucca Mountain tuffs.

Water-Resources Investigations Report↗
USGS2007

Aquifer susceptibility to perchlorate contamination in a highly urbanized environment

Perchlorate contamination from anthropogenic sources has been released into the Rialto-Colton, California, USA, groundwater flow system since the 1940s during its production, distribution, storage, and use. Preliminary analysis of lithological, geophysical, and water-chemistry data provided new understanding of the pathways of perchlorate migration that aid in assessing the susceptibility of drinking-water supplies to contamination within the Rialto-Colton basin. Vertical migration of perchlorate into the main water-producing aquifers is restricted by an areally extensive old soil surface; however, perchlorate data indicate contamination below this soil surface. Possible pathways for the downward migration of the contaminated water include wellbore flow and discontinuities in the old soil surface. Horizontal migration of perchlorate is influenced by lithology and faults within the basin. The basin fill is a heterogeneous mixture of boulders, gravel, sand, silt, and clay, and internal faults may restrict perchlorate migration in some areas.

California↗