Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Carbon Capture Science and Technology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,661 records · Page 17Linked to original sources
USGS2025

Evaluating mass flow meter measurements from chambers for greenhouse gas emissions from orphan wells and other point sources

This study evaluates the performance of a rigid gas flux chamber equipped with a mass flow meter (MFM) for measuring gas emissions from leaking orphan wells and similar pressure-driven gas point sources. We conducted a series of laboratory and field experiments to evaluate the sensitivity, stability, and dynamic range of an MFM chamber system and found an optimal method for sealing the chamber to the ground to isolate the emission source. From these results, we estimate the effects of different soil gas permeabilities on measurements and identify the uncertainty of environmental processes that can impact measurements. Simulations of an MFM chamber are compared to those of a dynamic flux chamber to contrast the data derived with both methodologies and illustrate the potential for measuring high variability leaks with the MFM chamber. Using a low flow resistance MFM and a chamber well-sealed to the ground, it is possible to measure leaks down to 1.08 x 10 -3 cubic meters per hour (m 3 h −1 ) (refenced to 25°/1 atm), corresponding to 0.77 grams per hour (g h −1 ) methane or 2.11 g h −1 carbon dioxide, with a mean uncertainty of 0.89 % relative standard deviation. Environmental processes such as heated gas inside the chamber from solar gain, wind blowing across the chamber vent, and changing humidity in the chamber, can cause variation in MFM measurements. Over 11 d of continuous monitoring under varying weather conditions, the standard deviation of the environmentally sourced signals was found to be 7.40 x 10 -3 m 3 h −1 (equivalent to or 5.27 g h −1 methane or 14.45 g h −1 carbon dioxide). Strategies to obtain the highest quality data from MFM chambers include burying the edges of the chamber below the surface sufficiently deep to seal the chamber edges against gas flow and soaking the dirt with water to lower the chances of escaping gases, while monitoring the gas flow and adjusting the chamber seal to achieve a maximum flow rate.

Atmospheric Measurement Techniques↗
USGS2025

Evidence for nonlocal sediment transport on hillslopes from fault scarp morphology

Hillslope sediment transport processes such as bioturbation, rainsplash, and granular mechanics occur across the entire planet. Yet, it remains uncertain how these small-scale processes act together to shape landscapes. Longstanding hillslope diffusion theory posits that hillslope processes are spatially limited, whereas new concepts of nonlocal sediment transport argue otherwise. However, each theory produces subtly different, but distinct, predictions for the evolution of fault scarps. We use the topographic change of fault scarps to demonstrate that hillslope processes produce nonlocal sediment transport. Analysis of a global compilation of 340 dated single-earthquake scarp profiles reveals a statistically significant ( p < 0.05 ) relationship between scarp age and scarp asymmetry, here defined as the ratio of imaginary to real components of the Fourier transform of absolute slope. Numerical simulations show that nonlocal models predict this relationship, whereas hillslope diffusion models do not. To further investigate this result, we examined the depositional geometry of a well-exposed colluvial wedge along the Wasatch fault in central Utah, United States. Our quantitative comparison between the exposure and numerical simulations reveals better agreement with the nonlocal model. Nonlocal sediment transport theory appears to best capture the physics of how hillslope processes shape fault scarps, yet hillslope diffusion provides a useful approximation in many cases. As the processes that act on fault scarps are nearly identical to those acting on hillslopes, our results provide evidence supporting nonlocality as a generalized model of hillslope sediment transport.

Utah↗
USGS2026

A temporal look at the influence of topographic amplification on earthquake-triggered landslides in 3D seismic simulations

Earthquakes are a primary trigger for landslides, often leading to catastrophic consequences. While numerous studies have explored the spatial distribution of earthquake-triggered landslides, understanding the interaction between seismic waves and topography remains a critical challenge. Topographic irregularities can cause seismic wave amplification, altering ground shaking, and can trigger landslides that are challenging for predictive models to anticipate. This study investigates the spatial and temporal evolution of topographically amplified landslides, focusing on coseismic landslides triggered by the Mw 7.5 mainshock of the 2018 Papua New Guinea earthquake and post-seismic landslides associated with its four aftershocks, each exceeding Mw 6.0. We employ low-frequency, three-dimensional numerical ground shaking simulations and data-driven multivariate analyses to examine how landslides evolved from the coseismic to post-seismic periods. Our findings reveal a spatial shift in landslide distribution, in which the mainshock triggered slope failures predominantly on steep hillslopes, and the aftershocks triggered landslides on gentler slopes, often near geologic boundaries. We attribute this transition partly to the earthquake legacy effect of the mainshock, where the mainshock caused weakening of these hillslopes, making them more prone to failure when aftershocks occur. Additionally, the concentration of failures along geologic contacts in the post-seismic phase suggests that site amplification, stemming from contrasts in subsurface materials, exerts a key influence on landslide occurrence. Although not explicitly captured in our current numerical simulations, this mechanism warrants further investigation for more accurate hazard modeling.

JGR Solid Earth↗
USGS2024

ECCOE Landsat quarterly Calibration and Validation report—Quarter 1, 2024

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 8 and 9 for quarter 1 (January–March), 2024. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . This quarterly report is the third to include analysis results for Landsat 9, which was launched in September 2021. The inclusion of Landsat 9 analysis results was dependent on two factors: a complete reprocessing of the Landsat 9 data archive and enough time elapsing to begin formulating lifetime trends. In April 2023, all Landsat 9 image data acquired since the satellite’s launch were reprocessed to take advantage of calibration updates identified by the ECCOE Landsat Cal/Val Team. Additional information about the Landsat 9 reprocessing effort is available at https://www.usgs.gov/landsat-missions/news/upcoming-reprocessing-all-landsat-9-data . Additional information about Landsat 9 prelaunch, commissioning, and early on-orbit imaging performance is available at https://www.mdpi.com/journal/remotesensing/special_issues/15B4V2K92K . This quarterly report is the first to not include analysis results for Landsat 7 because Enhanced Thematic Mapper Plus imaging was suspended on January 19, 2024, after the satellite transitioned into full sunlight. The satellite has been drifting since early 2022 after being lowered from the nominal orbit altitude, and the transition into full sunlight is a result of the satellite operating in its extended science mission. Additional information about the imaging suspension is available at https://www.usgs.gov/landsat-missions/news/landsat-7-imaging-suspended . Additional information about the Landsat 7 extended science mission is available at https://www.usgs.gov/landsat-missions/landsat-7-extended-science-mission .

Open-File Report↗
USGS2024

ECCOE Landsat quarterly Calibration and Validation report—Quarter 2, 2024

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 8 and 9 for quarter 2 (April–June) of 2024. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . This is the fourth quarterly report to include analysis results for Landsat 9, which was launched in September 2021. The inclusion of Landsat 9 analysis results was dependent on two factors: a complete reprocessing of the Landsat 9 data archive and enough time elapsing to begin formulating lifetime trends. In April 2023, all Landsat 9 image data acquired since the satellite’s launch were reprocessed to take advantage of calibration updates identified by the ECCOE Landsat Cal/Val Team. Additional information about the Landsat 9 reprocessing effort is available at https://www.usgs.gov/landsat-missions/news/upcoming-reprocessing-all-landsat-9-data . Additional information about Landsat 9 prelaunch, commissioning, and early on-orbit imaging performance is available at https://www.mdpi.com/journal/remotesensing/special_issues/15B4V2K92K . This is the second quarterly report that does not include analysis results for Landsat 7 because Enhanced Thematic Mapper Plus imaging was suspended on January 19, 2024, after the satellite transitioned into full sunlight. The satellite has been drifting since early 2022 when it was lowered from the nominal orbit altitude, and the transition into full sunlight is a result of the satellite operating in its extended science mission. Additional information about the imaging suspension is available at https://www.usgs.gov/landsat-missions/news/landsat-7-imaging-suspended . Additional information about the Landsat 7 extended science mission is available at https://www.usgs.gov/landsat-missions/landsat-7-extended-science-mission .

Open-File Report↗
USGS2026

Preliminary bedrock geologic map of the Port Henry quadrangle, Essex County, New York, and Addison County, Vermont

Introduction The bedrock geology of the 7.5-minute Port Henry quadrangle consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 Ga (giga-annum). In the Port Henry quadrangle, the AMCG metaigneous rocks (Yhg, Ygb, Yanw) intruded older, mostly metasedimentary rocks of the Grenville Complex during the middle to late Shawinigan orogeny (~1,160–1,150 Ma [mega-annum]). All rocks were subsequently metamorphosed to upper amphibolite to granulite facies conditions during the 1,080–1,050 Ma Ottawan orogeny. New mapping reveals four periods of deformation: (1) D1 produced rarely preserved isoclinal folds in the paragneiss and marble and predates AMCG magmatism. (2) Subsequent D2 deformation produced the dominant gneissic fabric preserved in the rock, recumbent folding, and deformed all the Proterozoic units in the map area. Syn- to late-D2 felsic magmatism resulted in the regionally extensive Lyon Mountain Granite Gneiss, which hosts numerous magnetite ore bodies. (3) Mylonitic extensional shear zones and core complex formation marked the beginning of D3 deformation. Protracted D3 deformation resulted in F3 upright folding, dome and basin formation, pegmatite intrusion, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron-ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. (4) D4 created northeast- and northwest-trending local high-grade ductile shear zones and boudinage, northwest-trending regional kilometer (km)-wide ductile shear zones, and crosscutting granitic pegmatite dikes. The development of the late-stage regional shear zones (D4) was likely due to the continuation of extensional doming and uplift from upper amphibolite facies conditions at the end of the Ottawan orogeny. The majority of iron-ore deposits in the Port Henry and adjacent Witherbee quadrangles are in the hanging wall of these extensional shear zones. In the Port Henry quadrangle, the km-wide Cheney Mountain shear zone is the result of D4 deformation. Kilometer-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. The Paleozoic rocks are part of the Early Cambrian to Late Ordovician carbonate bank on the ancient margin of Laurentia. The approximately 1-km-thick Cambrian to Ordovician stratigraphy records a transition from synrift clastics to passive-margin peritidal carbonate buildups to gradually deeper-water subtidal- to shelf-carbonates during foreland basin development associated with the Taconic orogeny. The Paleozoic rocks are weakly folded and block faulted. Large areas of the Champlain Valley are covered by undifferentiated glacial deposits, some of which contain mapped landslides. The map also shows waste rock piles and tailings from historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondacks, provide a context for historical iron mines in the eastern Adirondacks, and update the stratigraphy of the Champlain Valley in New York and Vermont. This Open-File Report includes a bedrock geologic map; a description of map units; a correlation of map units; and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information.

New York, Vermont↗
USGS2025

Quality of groundwater used for domestic supply in the Gilroy-Hollister basin and surrounding areas, California, 2022

More than 2 million Californians rely on groundwater from domestic wells for drinking-water supply. This report summarizes a 2022 California Groundwater Ambient Monitoring and Assessment Priority Basin Project (GAMA-PBP) water-quality survey of 33 domestic and small-system drinking-water supply wells in the Gilroy-Hollister Valley groundwater basin and the surrounding areas, where more than 20,000 residents are estimated to utilize privately owned domestic wells. The study area includes the Llagas subbasin in the north, the North San Benito subbasin in the south, and the surrounding uplands. The study was focused on groundwater resources used for domestic drinking-water supply, which are mostly drawn from shallower parts of aquifer systems rather than those of groundwater resources used for public drinking-water supply in the same area. This assessment characterized the quality of ambient groundwater in the aquifer before filtration or treatment, rather than the quality of drinking water delivered to the tap. To provide context, the measured concentrations of constituents in groundwater were compared to Federal and California State regulatory and non-regulatory benchmarks for drinking-water quality. A grid-based method was used to estimate the areal proportions of groundwater resources used for domestic drinking wells that have water-quality constituents present at high concentrations (above the benchmark), moderate concentrations (between one-half of the benchmark and the benchmark for inorganic constituents, or between one-tenth of the benchmark and the benchmark for organic constituents), and low concentrations (less than one-half or one-tenth the benchmark for inorganic and organic constituents, respectively). This method provides statistically representative results at the study-area scale and permits comparisons to other GAMA-PBP study areas. In the study area, inorganic constituents in groundwater were greater than regulatory benchmarks (U.S. Environmental Protection Agency [EPA] or State of California maximum contaminant levels [MCLs]) for public drinking-water quality in 24 percent of domestic groundwater resources. The inorganic constituents present at concentrations greater than MCLs for drinking water were nitrate (as nitrogen), barium, chromium, and selenium. Total dissolved solids (TDS) or manganese were present at concentrations greater than the secondary maximum contaminant levels (SMCLs) that the State of California uses as aesthetic-based benchmarks in 48 percent of domestic groundwater resources. No volatile organic compounds or pesticide constituents were present at concentrations greater than regulatory benchmarks. Total coliform bacteria and enterococci were detected in 4 percent of domestic groundwater resources. Per- and polyfluoroalkyl substances (PFAS) were detected in 19 percent of domestic groundwater resources, and 10 percent had concentrations greater than recently enacted (April 2024) EPA MCLs. Physical and chemical factors from natural and anthropogenic sources that could affect the groundwater quality were evaluated using results from statistical testing of associations between constituent concentrations and potential explanatory variables. In this study, relevant physical factors include well construction characteristics, groundwater age, site proximity to groundwater recharge or discharge zones, and potential sources of contamination. Relevant chemical factors include the initial chemistry of the recharge water, the mineralogy of the aquifer sediments, and the subsequent shifts in chemistry as biologic and geologic reactions alter groundwater in the subsurface. Nitrate concentrations were correlated to agricultural land use, distance from the boundary of the Gilroy-Hollister Valley groundwater basin, and the proportion of modern (post-1950s) water captured by the well. Denitrification under anoxic redox conditions can mitigate some nitrate derived from fertilizer application. Total dissolved solids primarily were derived from water-rock interactions with soils and aquifer materials in the study area, but there were high concentrations where agricultural practices contributed additional TDS. Mineralogy of aquifer sediments and rocks also affect barium, selenium, boron, and chromium concentrations in the Gilroy-Hollister Valley groundwater basin. PFAS were positively correlated with urban land use and the proportion of modern water captured by the well.

California↗
USGS2024

RegionGrow3D: A deterministic analysis for characterizing discrete three-dimensional landslide source areas on a regional scale

Regional-scale characterization of shallow landslide hazards is important for reducing their destructive impact on society. These hazards are commonly characterized by (a) their location and likelihood using susceptibility maps, (b) landslide size and frequency using geomorphic scaling laws, and (c) the magnitude of disturbance required to cause landslides using initiation thresholds. Typically, this is accomplished through the use of inventories documenting the locations and triggering conditions of previous landslides. In the absence of comprehensive landslide inventories, physics-based slope stability models can be used to estimate landslide initiation potential and provide plausible distributions of landslide characteristics for a range of environmental and forcing conditions. However, these models are sometimes limited in their ability to capture key mechanisms tied to discrete three-dimensional (3D) landslide mechanics while possessing the computational efficiency required for broad-scale application. In this study, the RegionGrow3D (RG3D) model is developed to broadly simulate the area, volume, and location of landslides on a regional scale (≥1,000 km 2 ) using 3D, limit-equilibrium (LE)-based slope stability modeling. Furthermore, RG3D is incorporated into a susceptibility framework that quantifies landsliding uncertainty using a distribution of soil shear strengths and their associated probabilities, back-calculated from inventoried landslides using 3D LE-based landslide forensics. This framework is used to evaluate the influence of uncertainty tied to shear strength, rainfall scenarios, and antecedent soil moisture on potential landsliding and rainfall thresholds over a large region of the Oregon Coast Range, USA.

Journal of Geophysical Research: Earth Surface↗
USGS2025

Remote single-station seismic monitoring of the July–October 2022 earthquake swarm at Tau volcano, American Samoa

From July to October 2022, a non-eruptive volcanic earthquake swarm occurred within ~15 km of Taʻū Island, located in eastern American Samoa. Felt reports from local residents were the only available information about the swarm when it started, as American Samoa lacked a seismic monitoring network. We developed a consistent single-station catalog for the entire swarm, using seismic data from the nearest station IU.AFI, ~250 km away. We applied the EQTransformer deep-learning model (Mousavi et al., 2020), automatically picking Pn and Sn arrivals on IU.AFI continuous data. We retained only events with Sn-Pn times of 22.5–25 seconds, consistent with the expected locations based on felt reports, then detected smaller swarm events with subsequent template-matching. This single-station catalog characterized the swarm’s onset and escalation to peak activity before a multi-agency field response team installed a local seismic network in mid-August 2022. This permanent seismic network captured the swarm’s decline. EQTransformer identified short S-P times on the first two locally deployed seismometers, both Raspberry Shake sensors, to constrain the swarm’s distance from Taʻū Island. Modern seismological processing methods, combined with basic observations such as felt reports, can quickly contribute useful information during an earthquake response in a poorly monitored region.

American Somoa↗
USGS2021

Geology, mineralogy, and cassiterite geochronology of the Ayawilca Zn-Pb-Ag-In-Sn-Cu deposit, Pasco, Peru

The Ayawilca deposit in Pasco, Peru, represents the most significant recent base-metal discovery in the central Andes and one of the largest undeveloped In resources globally. As of 2018, it hosts an 11.7 Mt indicated resource grading 6.9% Zn, 0.16% Pb, 15 g/t Ag, and 84 g/t In, an additional 45.0 Mt inferred resource grading 5.6% Zn, 0.23% Pb, 17 g/t Ag, and 67 g/t In, and a separate Sn-Cu-Ag inferred resource of 14.5 Mt grading 0.63% Sn, 0.21% Cu, and 18 g/t Ag. Newly obtained U–Pb dates for cassiterite by LA-ICP-MS (22.77 ± 0.41 and 23.05 ± 2.06 Ma) assign the Ayawilca deposit to the Miocene polymetallic belt of central Peru. The polymetallic mineralization occurs as up to 70-m-thick mantos hosted by carbonate rocks of the Late Triassic to Early Jurassic Pucará Group, and subordinately, as steeply dipping veins hosted by rocks of the Pucará Group and overlying Cretaceous sandstones-siltstones of the Goyllarisquizga Group. Relicts of a distal retrograde magnesian skarn and cassiterite (stage pre-A) were identified in the deepest mantos. The volumetrically most important mineralization at Ayawilca comprises a low-sulfidation assemblage (stage A) with quartz, pyrrhotite, arsenopyrite, chalcopyrite, Fe-rich sphalerite, and traces of stannite and herzenbergite. Stage A sphalerite records progressive Fe depletion, from 33 to 10 mol% FeS, which is compatible with the observed transition from low- to a subsequent intermediate-sulfidation stage (B) marked by the crystallization of abundant pyrite and marcasite. Finally, during a later intermediate-sulfidation stage (C) sphalerite (up to 11 mol% FeS), galena, native bismuth, Cu-Pb-Ag sulfosalts, siderite, Mn-Fe carbonates, kaolinite, dickite, and sericite were deposited. This paragenetic evolution shows striking similarities with that at the Cerro de Pasco Cordilleran-type polymetallic deposit, even if at Ayawilca stage C did not reach high-sulfidation conditions. The occurrence of an early retrograde skarn assemblage suggests that the manto bodies at Ayawilca formed at the transition between distal skarn and skarn-free (Cordilleran-type) carbonate-replacement mineralization. Mineral assemblages define a T- f S 2 evolutionary path close to the pyrrhotite-pyrite boundary. Buffering of hydrothermal fluids by underlying Devonian carbonaceous phyllites of the Excelsior Group imposed highly reduced conditions during stage A mineralization (log f O 2 < − 30 atm). The low f O 2 favored efficient Sn mobility during stages pre-A and A, in contrast to other known ore deposits in the polymetallic belt of central Peru, in which the occurrence of Sn minerals is minor. Subsequent cooling, progressive sealing of vein walls, and decreasing buffering potential of the host rocks promoted the shift from low- (stage A) to intermediate-sulfidation (stages B and C) states. LA-ICP-MS analyses reveal significant In contents in Fe-rich sphalerite (up to 1.7 wt%), stannite (up to 1908 ppm), and chalcopyrite (up to 1185 ppm). The highest In content was found in stage A sphalerite that precipitated along with chalcopyrite and stannite, thus pointing to the early, low-sulfidation assemblage as prospective for this high-tech metal in similar mineral systems. Indium was likely incorporated into the sphalerite crystal lattice via Cu + + In 3+ ↔ 2 Zn 2+ and (Sn, Ge) 4+ + (Ga, In) 3+ + (Cu + Ag) + ↔ 4 Zn 2+ coupled substitutions. Indium incorporation mechanisms into the stannite and chalcopyrite crystal lattices remain unclear.

Pasco↗
USGS2025

Irrigated agriculture influences selenium levels in an endangered marsh bird

Selenium bioaccumulation in aquatic food webs poses risks to wildlife, particularly in wetlands receiving irrigation runoff. The Salton Sea, California’s largest lake, is primarily sustained by agricultural drainage. This drainage creates wetland habitat along the lakeshore that many bird species depend on, including the federally endangered Yuma Ridgway’s rail ( Rallus obsoletus yumanensis ). However, these marshes may pose an ecological trap – attracting rails despite high selenium exposure. We captured rails during the 2020–2023 breeding seasons and compared rail selenium levels within three types of marshes (fed with irrigation runoff, Colorado River water, or groundwater). We collected blood, breast feathers, and head feathers of rails in all three water sources for selenium comparisons. We tagged adult rails with GPS transmitters to locate nests and foraging locations where we collected eggshells, unhatched eggs, and prey. We assessed selenium exposure by collecting multiple prey species commonly eaten by rails in all three water sources. Selenium concentrations varied among sampling locations. Selenium concentrations in most sample types were predominately influenced by water source and marsh inflow velocity (sometimes in combination with marsh size). Distance to inflow, however, did not influence selenium concentrations in any sample type. Selenium concentrations were highest in agricultural-fed marshes compared to river-fed and spring-fed marshes. Increased marsh inflow velocities resulted in lower selenium concentrations. Given the risk of an ecological trap, our results suggest that supplementing wetlands with Colorado River water could mitigate selenium bioaccumulation in Yuma Ridgway’s rails.

California↗
USGS2026

Surface-wave relocation and characterization of the 2024–2025 dyking episode along the Fentale–Dofen segment of the Ethiopian rift

From late-December 2024 to mid-March 2025, a 50-km-long dyke intrusion triggered over 300 earthquakes (magnitude 4 to 5.9) between Fentale and Dofen volcanoes along the Northern Main Ethiopian Rift. Dyke intrusions periodically occur along the Fentale–Dofen magmatic segment and are an expression of ongoing rift extension. Preliminary analyses using interferometric synthetic aperture radar revealed extensive ground deformation (up to 60 cm), which closely matched the temporal and spatial evolution of surface manifestations and earthquake locations from global catalogues. While global catalogues are critical for real-time monitoring, the precision of locations in remote and or sparsely instrumented regions can be low. In this investigation, we present surface-wave relocation results of the dyking episode that began near Fentale volcano in December 2024. We estimate relative locations using differential traveltimes measured from regional-to-teleseismic distance surface-wave observations of earthquakes reported by the U.S. Geological Survey. Relative relocations reduce the initial region of diffuse seismicity to a 50-km-long narrow band bounding the strike of surface manifestations and the zone of maximum surface deformation. We demonstrate the precision of surface-wave relocations over incremental time periods, capturing the progression of dyking from seismic onset through seismic migration and caldera subsidence. Results showcase the utility of surface-wave relocations in the characterization of dyking episodes and provide complementary insights into the current understanding of the Fentale–Dofen volcanic plumbing system.

Geophysical Journal International↗
USGS2026

Light-dependent activity of deepwater sculpin (Myoxocephalus thompsonii) across substrates with and without predation risk

Light availability strongly influences predator–prey interactions in deepwater ecosystems, where visual constraints shape both foraging success and prey behavior. The behavioral response of deepwater sculpin ( Myoxocephalus thompsonii ) to siscowet lake trout ( Salvelinus namaycush siscowet ) was studied under ecologically relevant light intensities spanning several orders of magnitude typical of daytime downwelling light in the 20–100 m depth range of Lake Superior. Trials were conducted over varying substrates (gravel, sand, and black fabric). Deepwater sculpin showed a significant preference for gravel over sand and black fabric. In the absence of siscowet, sculpin movement frequency increased as light intensity decreased. Sculpin reaction distance to siscowet was influenced by both light and substrate. Reaction distance was shortest at low light intensities, peaked at intermediate light intensities (3.05 × 10⁹ to < 6.0 × 10⁹ photons m⁻2 s⁻1), and declined again at the highest light intensities tested. In the presence of siscowet, sculpin activity was suppressed at the upper end of the light range (≥ 6.0 × 10⁹ photons m⁻2 s⁻1). The greatest increase in movement occurred between 6.0 × 10⁹ and 3.05 × 10⁹ photons m⁻2 s⁻1, which corresponded to the range where siscowet prey capture declined, suggesting sculpin exploit this low-light window to move with reduced risk. Reduced activity in the presence of predators is common among cryptic species, and our findings suggest that sculpin restrict movement at higher light levels to avoid detection by siscowet.

Wisconsin↗
USGS1996

Technique for estimating magnitude and frequency of peak flows in Maryland

A convenient and reliable technique for estimating flood magnitudes is required for effective flood-plain management and for the efficient design of bridges, culverts, embankments, and flood-protection structures. Methods are presented for estimating peak-flow magnitudes of selected frequencies, ranging from 2 to 500 years, for all nontidal drainage basins in Maryland. The methods were developed by generalized least-squares regression techniques using data from 219 gaged basins in and near Maryland. The State is divided into five hydrologic regions: the Appalachian Plateaus and Allegheny Ridges region, the Blue Ridge and Great Valley region, the Piedmont region, the Western Coastal Plain region, and the Eastern Coastal Plain region. These regions correspond to the physiographic provinces of the State, with the exceptions that (1) the Coastal Plain Province is divided into two hydrologic regions, and (2) there is no distinct hydrologic region corresponding to the Valley and Ridge Province as it is divided into its constituent Allegheny Ridges and Great Valley subdivisions. Sets of equations for calculating peak discharges based on physical basin characteristics are provided for each of the regions. Based on the peak-flow equations, methods for estimating peak flows are presented for ungaged and gaged streams in Maryland. The methods and equations are supported by generalized least-squares analysis of basin and flood-frequency characteristics data from 219 drainage basins in and near Maryland. estimates for each of the five regions are calculated using combinations of the fol-lowing basin characteristics: drainage area, forest cover, basin relief, carbonate rock coverage, storage, and runoff-curve number. Drainage area contributes to the estimate in all five study regions. Carbonate rock coverage is used only in the Blue Ridge and Great Valley region. Storage and runoff-curve number are used solely in the Eastern Coastal Plain region. All other basin characteristics are used in two or more regions. Standard errors of estimate for the regression equations range from 19 to 31 percent in the Appalachian Plateaus and Allegheny Ridges region, 34 to 47 percent in the Blue Ridge and Great Valley region, 33 to 48 percent in the Piedmont region, 45 to 64 percent in the Western Coastal Plain region, and 36 to 42 percent in the Eastern Coastal Plain region.

Maryland↗
USGS2025

Reconstruction of Holocene and Last Interglacial vegetation dynamics and wildfire activity in Southern Siberia

Wildfires are a rapidly increasing threat to boreal forests. While our understanding of the drivers behind wildfires and their environmental impact is growing, it is mostly limited to the observational period. Here we focus on the boreal forests of southern Siberia and exploit a U–Th-dated stalagmite from Botovskaya Cave, located in the upper Lena region of southern Siberia, to document wildfire activity and vegetation dynamics during parts of two warm periods: the Last Interglacial (LIG; specifically part of the Last Interglacial maximum between 124.1 and 118.8 ka) and the Holocene (10–0 ka). Our record is based on levoglucosan (Lev), a biomarker sensitive to biomass burning, and on lignin oxidation products (LOPs) that discriminate between open and closed forest and hard- or softwood vegetation. In addition, we used carbonate carbon stable isotope ratios ( δ 13 C ), which reflect a dominant control of the host rock, to evaluate soil respiration and local infiltration changes. Our LOP data suggest that, during the Last Interglacial, the region around Botovskaya Cave was characterised by open forest, which by ca. 121.5 ka underwent a transition from fire-resistant hardwood to fire-prone softwood. The Lev record indicates that fire activity was high and increased towards the end of Last Interglacial just before 119 ka. In contrast, the Holocene was characterised by a closed-forest environment with mixed hard- and softwood vegetation. Holocene fire activity varied but at a much lower level than during the Last Interglacial. We attribute the changes in wildfire activity during the intervals of interest to the interplay between vegetation and climate. The open forests of the Last Interglacial were more likely to ignite than their closed Holocene equivalents, and their flammability was aided by warmer and drier summers and a stronger seasonal temperature contrast due to the increase in seasonal insolation difference compared to the Holocene. Our comparison of the last two interglacial intervals suggests that, with increasing global temperatures, the boreal forest of southern Siberia may become progressively more vulnerable to higher wildfire activity.

Botovskaya Cave, Siberia↗
USGS2025

Four-band image mosaic of the Colorado River Corridor downstream of Glen Canyon Dam in Arizona, derived from the May 2021 airborne image acquisition

In May 2021, the U.S. Geological Survey’s Grand Canyon Monitoring and Research Center acquired airborne multispectral high-resolution data for the Colorado River in the Grand Canyon, Arizona. The image data, which consist of four spectral bands (red, band 1; green, band 2; blue, band 3; and near infrared, band 4) with a ground resolution of 20 centimeters, are available as 16-bit unsigned-integer GeoTIFF files in Sankey and others (2024) (available online at https://doi.org/10.5066/P9BBGN6G ). The image files are projected in the State Plane Coordinate System, using the central Arizona zone (202) with the North American Datum of 1983 National Adjustment of 2011. The assessed spatial accuracy for these data is based on 47 ground-control points that were independent from the ground-control points used by the contractor for aerotriangulation and is reported at the 95-percent confidence level as 0.514 meter (m) and a root mean square error of 0.297 m. The intended uses of this dataset are primarily in support of scientific research and monitoring applications. Examples of these applications include high-resolution spatial and temporal change detection of the river channel, geomorphic landforms, riparian vegetation, and backwater and nearshore habitat, as well as other ecosystem-wide mapping. These imagery data also serve as reference material for field science mission planning, as base data for field data collection including community science activities, and as a highly detailed guide for technical boat operation during science activities such as reconnaissance for nighttime missions and navigating rapids during low flows.

Arizona, Nevada, Utah↗
USGS2025

Constraining landslide frequency across the United States to inform county-level risk reduction

Informative landslide hazard estimates are needed to support landslide mitigation strategies to reduce landslide risk across the United States. Whereas existing national-scale landslide susceptibility products assess where landslides are likely to occur, they do not address how often , which is a critical element of landslide hazard and risk assessments. In particular, the U.S. Federal Emergency Management Agency's National Risk Index (NRI) requires landslide frequency estimates to inform expected annual loss estimates. We present county-level landslide frequency (landslides per area per year) estimates for the 50 US states. We applied Bayesian negative binomial regression to estimate both the expected (average) reported landslide frequency and full distribution of annual landslide counts for each county. We compared a suite of models that used combinations of landslide-susceptible area, probability of potentially triggering earthquakes, frequency of potentially triggering precipitation, and ecological region as predictors. We trained our models with landslide inventory data from counties with the most comprehensive records available nationwide and used zero-inflated negative binomial distributions as an incompleteness model to correct for temporal reporting gaps. We selected a preferred frequency model to inform the NRI based on information criteria and physically plausible parameter estimates. The model showed that average annual reported landslide frequencies vary by 5 orders of magnitude across US counties, ranging from 0.002 (0.00015–0.05) landslides 1000 km −2 yr −1 in Kusilvak Census Area, Alaska, to 29 (19–46) landslides 1000 km −2 yr −1 in Lake County, California, reflecting the country's strong variations in landslide susceptibility, earthquake probability, and other factors for which ecological region serves as a proxy. Counties with estimated frequencies in the top 20 % of all counties are predominately along the West Coast of the continental United States, in mountainous regions of the Pacific Northwest and Intermountain West, in locally steep or earthquake-prone regions of the Midwest and Southeast, along the Appalachians, in southern and southeastern Alaska, and on some Hawaiian islands. By examining the number of landslides predicted in 99th percentile years for each county, we identified that 26 % of US counties likely have potential for widespread landsliding with more than 10 landslides 1000 km −2 yr −1 , even when such large events have not been reported in the training data for that county. Overall, our results better represent the range of possible landslide frequencies and spatial variations than previous national-scale estimates reported in the NRI, and our approach can inform other risk-reduction and loss-mitigation efforts across the United States and globally.

Natural Hazards and Earth System Sciences↗
USGS1986

Potential for leakage among principal aquifers in the Memphis area, Tennessee

The principal aquifers in the Memphis area consist primarily of sand or sand and gravel, and the confining beds consist of clay, silt, sand, and lignite. The Jackson Formation and upper part of the Claiborne Group serve as the confining bed separating the water table aquifers from the Memphis Sand; the Flour Island Formation separates the Memphis Sand from the Fort Pillow Sand. Differences in total hydraulic head among the principal aquifers in the Memphis urban area result in vertical hydraulic gradients which create a potential for inter-aquifer exchange of water. Throughout this area, the gradient is downward from the water table aquifers to the Memphis Sand. In the central part of the Memphis urban area, the vertical hydraulic gradient is upward from the Fort Pillow Sand to the Memphis Sand, and in the eastern and western parts, it is downward from the Memphis Sand to the Fort Pillow Sand. The vertical distribution of carbon-14 data for water from the fluvial deposits, Memphis Sand, and Fort Pillow Sand shows an increase in the relative age of the water with depth. The areal distribution of carbon-14 data for water from the upper part of the Memphis Sand indicates that relatively recent water has been brought into the major cone of depression in the potentiometric surface of the Memphis Sand, either by horizontal movement or from downward vertical leakage. The normal, near-surface geothermal gradient in the Memphis area was determined to be 0.6 C/100 ft. Deviations from the normal geothermal gradient, in areas affected by intense pumping from the Memphis Sand, indicate that downward vertical leakage occurs from the water table aquifers through the Jackson-upper Claiborne confining bed to the Memphis Sand. The velocity of downward vertical leakage of water from the Memphis Sand through the Flour Island confining bed to the Fort Pillow Sand was determined to be 0.0066 ft/day by analysis of borehole temperature data from an observation well in the northeastern part of the Memphis area. From this velocity and the head difference between the Memphis Sand and the Fort Pillow Sand at this locality, the hydraulic conductivity of the Flour Island confining bed was determined to be 0.00114 ft/day. (Lantz-PTT)

Tennessee↗