3-D wave propagation simulations of Mw 6.5+ earthquakes on the Tacoma Fault, Washington state, considering the effects of topography, a geotechnical gradient, and a fault damage zone

Ian P. Stone; Erin A. Wirth; Alex R. Grant; Arthur D. Frankel

doi:10.1785/0120230083

Home/Archive/USGS

USGS · 70250820

3-D wave propagation simulations of Mw 6.5+ earthquakes on the Tacoma Fault, Washington state, considering the effects of topography, a geotechnical gradient, and a fault damage zone

Ian P. Stone·Erin A. Wirth·Alex R. Grant·Arthur D. Frankel

View original source ↗Export metadata ↓

Abstract

We simulate shaking in Tacoma, Washington, and surrounding areas from M w 6.5 and 7.0 earthquakes on the Tacoma fault. Ground motions are directly modeled up to 2.5 Hz using kinematic, finite‐fault sources; a 3D seismic velocity model considering regional geology; and a model mesh with 30 m sampling at the ground surface. In addition, we explore how adjustments to the seismic velocity model affect predicted shaking over a range of periods. These adjustments include the addition of a region‐specific geotechnical gradient, surface topography, and a fault damage zone. We find that the simulated shaking tends to be near estimates from empirical ground‐motion models (GMMs). However, long‐period ( T = 5.0 s) shaking within the Tacoma basin is typically underpredicted by the GMMs. The fit between simulated and GMM‐derived short‐period ( T = 0.5 s) shaking is significantly improved with the addition of the geotechnical gradient. From comparing different M w 6.5 earthquake scenarios, we also find that the response of the Tacoma basin is sensitive to the azimuth of incoming seismic waves. In adding surface topography to the simulation, we find that average ground motion is similar to that produced from the nontopography model. However, shaking is often amplified at topographic highs and deamplified at topographic lows, and the wavefield undergoes extensive scattering. Adding a fault damage zone has the effect of amplifying short‐period shaking adjacent to the fault, while reducing far‐field shaking. Intermediate‐period shaking is amplified within the Tacoma basin, likely due to enhanced surface‐wave generation attributable to the fault damage zone waveguide. When applied in the same model, the topography and fault damage zone adjustments often enhance or reduce the effects of one another, adding further complexity to the wavefield. These results emphasize the importance of improving near‐surface velocity model resolution as waveform simulations progress toward higher frequencies.

Explore related subjects

Bulletin of the Seismological Society of America Article

Source-reported bounding extent: 47.09223788435119° to 47.52066759288792° latitude; -122.94849646816715° to -121.84278435348952° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Ian P. Stone, Erin A. Wirth, Alex R. Grant, Arthur D. Frankel. 2023-09-06. 3-D wave propagation simulations of Mw 6.5+ earthquakes on the Tacoma Fault, Washington state, considering the effects of topography, a geotechnical gradient, and a fault damage zone. https://doi.org/10.1785/0120230083

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Efficient physics‐informed ground‐motion simulations with reduced‐order models: CyberShake implications and high‐resolution site terms for southern San Andreas fault earthquakes

Recent advances in Probabilistic Seismic Hazard Analysis (PSHA) leverage physics‐based ground‐motion simulations to estimate seismic hazard, such as the CyberShake project. However, computational costs quickly escalate when performing PSHA for numerous faults or sites and can become prohibitively expensive. To reduce computational demands, CyberShake uses reciprocity and interpolates physics‐informed corrections from simulations conducted at fewer locations, but the accuracy of these interpolations remains poorly quantified. To quantify the interpolation accuracy, we derive high‐resolution, frequency‐dependent site terms for southern California and compare them with interpolated site terms using the CyberShake approach. We accomplish this by performing a set of earthquake point‐source simulations distributed along the nonplanar fault geometry for the southern San Andreas fault (SSAF) extending from Bombay Beach to Lake Hughes. Using SeisSol, we simulate three minutes of viscoelastic seismic wave propagation for these sources and store the horizontal‐component Green’s functions for 480,000 sites. We then use a scientific machine learning approach based on interpolated proper orthogonal decomposition to construct an accurate reduced‐order model of the Green’s functions to efficiently predict effective amplitude spectra (EAS) for finite‐source rupture models of SSAF earthquakes. Using minimum curvature interpolation with tension, as used in CyberShake, we compare the interpolated site terms against our high‐resolution site terms. We identify local discrepancies with EAS differing by up to a factor of approximately three. Furthermore, we identify locations where unexpectedly high or low ground motions are missed when using the interpolated dataset for these earthquakes. We estimate that our approach may be used within CyberShake to reduce the time‐to‐solution by a factor of 336 for the entire earthquake rupture forecast. Our analysis of physics‐based site terms provides more insight into the seismic hazard due to SSAF ruptures and guides future developments by combining high‐performance computing and reduced‐order modeling techniques for PSHA.

California↗

USGS2026

Simulation-based scenario ShakeMaps for large magnitude (MW6.5+) crustal earthquakes on the Seattle, Tacoma, and southern Whidbey Island faults, Washington, USA

Scenario ground‐motion maps based on empirical ground‐motion models (GMMs) provide a rapid and generally reliable means of estimating the amplitude and distribution of earthquake shaking. However, because GMMs are designed for broad applicability, they often rely on simplified representations of Earth structure, which can limit their accuracy in regions with complex source, path, and site effects. This can substantially impact the accuracy of predicted shaking in areas like western Washington State, where deep, interconnected basin structure exerts a strong influence on seismic‐wave propagation. In this study, we present a new suite of simulation‐based scenario ShakeMaps that characterize ground shaking from large‐magnitude ( ⁠ M W 6.5–7.5) earthquakes on the Seattle, Tacoma, and southern Whidbey Island faults. These maps are developed using results from recent 3D wave propagation simulations ( Stone et al. , 2022 , 2023 , 2025 ) that incorporate realistic rupture geometries, variable slip distributions, and a regional 3D seismic velocity model with shallow soils. Broadband ground motions are estimated by combining the low‐frequency (<1 Hz) deterministic seismograms from these studies with high‐frequency (1–10 Hz) stochastic seismograms. Simulated ground motions are corrected to account for the enforced minimum shear‐wave velocity and nonlinear site response. The resulting ShakeMaps represent median ground‐shaking estimates derived from multiple rupture scenarios with varying slip distributions and hypocenter locations for each fault. To extend ShakeMap coverage beyond the simulation domain (i.e., into eastern Washington, northern Oregon, and southwestern British Columbia), we scale GMM‐based ground‐motion estimates using amplification patterns observed in the simulations. These new ShakeMaps reveal the substantial influence of deep basin structure on shaking intensity, underscoring the importance of considering crustal structure complexity in regional hazard assessments for the Pacific Northwest.

Washington↗

USGS2026

Testing characteristic magnitude distributions in modern PSHA models

The characteristic magnitude distribution hypothesis predicts a higher rate of large earthquakes than a Gutenberg–Richter extrapolation of the small‐earthquake rate would imply. Characteristic magnitude distributions have been commonly applied to faults in probabilistic seismic hazard analysis (PSHA), and in modern models they can emerge from the way short‐term seismicity constraints are combined with long‐term geologic and geodetic constraints. We test the characteristic magnitude distribution hypothesis by comparing the fault‐based magnitude distributions from the 2023 update to the National Seismic Hazard Model (NSHM23) in the Western United States with observed seismicity over the past 93 yr. We find that observed magnitude distributions fall outside the model‐predicted confidence bounds in regions where NSHM23 produces characteristic magnitude distributions: in these regions, the model predicts higher rates of large earthquakes than are observed. An analysis of the earlier California model (Uniform California Earthquake Rupture Forecast, version 3) also reveals discrepancies between the modeled and observed magnitude distributions. In addition, we find that observed magnitude distributions near modeled faults are not significantly different from those in background regions. These results challenge the prevalence of characteristic magnitude distributions in fault‐based seismic hazard models and call for a reassessment of how disparate data sets are integrated in PSHA.

western United States↗