Geology ReportsSearch

USGS · 70160867

Geology and ground-water resources of the island of Hawaii

Abstract

Hawaii, the largest island in the Hawaiian group, is 93 miles long, 76 miles wide, and covers 4,030 square miles. Mauna Loa Volcano is 13,680 feet high and Mauna Kea is 13,784 feet high. Plate 1 shows the geology, wells, springs, and water-development tunnels. Plate 2 is a map and description of points of geologic interest along the main highways. Plate 3 (same sheet as plate 2) shows highways and points of geologic interest in Hawaii National Park area. The volcanic terms used in the report are defined. Hawaii was built by five volcanoes. All the rocks are volcanic, except for minor amounts of sedimentary rock derived from them. Mauna Loa and Kilauea volcanoes erupt often; Hualalai Volcano last erupted in 1801; Mauna Kea has had Recent but no historic eruptions; Kohala Mountain has long been extinct. Kohala Mountain constitutes the northern end of the island. It is built largely of rocks of the Pololu volcanic series which are dominantly olivine basalt with a few thin intercalated beds of vitric basaltic ash. After the eruption of this series, Kohala Volcano was deeply eroded on the windward (northeastern) side, and a deep soil formed on its other slopes. Later, oligoclase andesite and trachyte lava flows, named the Hawi volcanic series, were erupted. They rest on soil at the top of the Pololu series, and lie in the valleys cut into the Pololu lavas on the windward slope. Both the Pololu and Hawi volcanics were erupted from three rift zones trending N. 35° W., S. 65° E., and S. 50° W. from the summit of the mountain. The rift zones are marked at the surface by rows or cinder cones, and beneath the surface by innumerable dikes. A caldera occupied the summit of the mountain at the beginning of the eruption of the Hawi lavas, and for a time confined the flows. It was gradually filled and the lava escaped northeastward into the large valleys. Some of the caldera faults can still be traced. A shallow graben indents the summit now. South of Kohala Mountain lies the much larger volcano of Mauna Kea. The early rocks of Mauna Kea constitute the Hamakua volcanic series. The lower member of this series consists chiefly of olivine basalt flows with intercalated thin beds of vitric basaltic ash. The olivine basalt of the lower member changes gradationally into the upper member, in which basalt and olivine basalt arc still abundant, but andesite also is present. Lavas of the upper member interfinger with Hawi lavas of Kohala Mountain. The Hamakua volcanic series is mantled with Pahala ash 5 to 20 feet thick, above which lie the rocks of the Laupahoehoe volcanic series. Locally the two series are separated by erosional unconformity, The Laupahoehoe lavas are dominantly andesite. The andesites erupted after the last glacial epoch are mapped separately on plate 1. The Laupahoehoe volcanic series, and probably also the Hamakua volcanic series, were erupted principally from three rift zones, trending west, northeast and south-southeast from the summit of the mountain. The upper slopes are studded with many large cinder cones, lying principally along the rift zones. Late in its geologic history, Mauna Kea was capped by a small glacier, presumably contemporaneous with the Wisconsin stage of glaciation in North America, which left conspicuous terminal, lateral, and ground moraines. Deposits exposed in canyons on the southern slope, formerly believed to be of glacial origin, are now believed to be volcanic explosion breccias. The main bulk of Hualalai Volcano is built of basalts of the Hualalai volcanic series. One flow of andesite has been found. The cinder and spatter cones lie principally along three rift zones which trend northwest, north, and southeast from the summit. On the northern slope of Hualalai Volcano lies the large trachyte pumice cone of Puu Waawaa, and its thick flow of trachyte. These are grouped together as the Waawaa volcanics. They are partly buried by later basalts from both Hualalai and Mauna Loa. The last eruption of Hualalai Volcano, in 1800–1801, produced olivine basalt. The earliest exposed rocks of Mauna Loa comprise the Ninole volcanic series. Several beds of altered vitric ash are intercalated with the lavas. Following eruption of the Ninole series, a long period or quiescence occurred, during which deep amphitheater-headed valleys were cut. This was followed by the eruption of the Kahuku volcanic series, consisting mostly of lavas with some thin beds of ash. The Rahuku series is overlain by the Pahala ash, which overlies also the Hilina volcanic series on Kilauea, the Hamakua volcanic series on Mauna Kea, and the Hawi volcanic series on Kohala, providing a rough datum for correlation of the lavas of the four mountains. Deposition of the Pahala ash was followed on Mauna Loa by eruption of the Kau volcanic series, which has continued until the present time. The historic and flaws of the Kau series are mapped separately on plate 1. The historic eruptions and volcanic activity of Mauna Loa are briefly described. The western and southern slopes of Mauna Loa are cut by normal faults along which the lower flanks of the mountain have slipped seaward. The Kau volcanic series and presumably also the Kahuku and Ninole volcanic series were erupted principally from vents along two rift zones which extend northeast and southwest from the summit caldera. The lavas of all three series are preponderantly olivine basalt. Many of the lavas contain small amounts of hypersthene. The Pahala ash on the northeastern and eastern slopes of Mauna Loa was derived largely from Mauna Kea. West and south of Kilauea Caldera, however, it was derived principally from Kilauea. Minor amounts were contributed by eruptions of Mauna Loa. It is a vitric basaltic ash, now generally altered to palagonite. The earliest exposed lavas and thin intercalated ash beds of Kilauea Volcano comprise the Hilina volcanic series. These are capped by the Pahala ash, which in turn, is overlain by the lavas and thin ash beds of the Puna volcanic series. The volcanics of both series were erupted along two rift zones, one extending southwestward from Kilauea Caldera, and the other extending southeastward for 5 miles and then bending sharply east by north. The lavas of both series are very largely olivine basalt. A few flows contain hypersthene. Augite phenocrysts are common in Mauna Loa lavas, but rare in those of Kilauea, indicating that crystallization has not progressed as far in the magma chamber of Kilauea Volcano as in that of Mauna Loa. Eruption of the Puna volcanic series has continued until the present time, the historic flows being separated from the prehistoric ones on plate 1. The historic eruptions and volcanic activity of Kilauea are briefly described. Kilauea Volcano originated on the southern slope of Mauna Loa where faults intersected the Eastern Fundamental Fissure of the Hawaiian Archipelago. The southern flank of Kilauea is cut by normal faults, along which the southern part is sliding seaward. The volcanoes of the island of Hawaii are believed to have started their activity in the Tertiary period. The great erosional period which followed deposition of the Pololu and Ninole volcanic series is placed near the end of the Pliocene. The Hilina and Hamakua volcanic series were probably erupted in the late Pliocene and earlier Pleistocene. The Hawi volcanic series and the Waawaa volcanics are probably early or middle Pleistocene in age. The main period of deposition of the Pahala ash was probably late in the middle Pleistocene or early in the upper Pleistocene. The Laupahoehoe volcanic series is late Pleistocene and Recent in age, most of the flows antedating the Wisconsin glaciation. The Hualalai volcanic series probably extends from Tertiary to historic time, and the Kau and Puna volcanic series from late Pleistocene to the present. A chapter is devoted to the petrography of the rocks in which are listed all reliable chemical rock analyses. The rocks of the island are highly permeable. Most of the rainfall sinks quickly into the ground. Perennial streams are present only on the windward slopes of Kohala Mountain and Mauna Kea. Most of the water sinks rapidly to the basal water table, where it floats on salt water according to the Ghyben-Herzberg principle. Basal water escapes in springs at or near sea level all along the coast. Only a very small proportion of it is recovered in wells. Along the windward coasts the basal water is of good quality and large supplies await development. Along the leeward coasts most of the basal water is brackish. In Kohala Mountain, much water is perched on ash beds in the Pololu volcanic series and on ash and soil at the base of the Hawi volcanic series. It escapes in perched springs in the big valleys and along the windward sea cliff and is recovered in tunnels. Along the windward slope of Mauna Keu, small amounts of water are perched by ash beds and dense lava flows in the Hamakua volcanic series. Small perched springs issue from these structures and water is recovered by tunnels. In the Kau District ash beds perch considerable water, which is recovered by many tunnels. On the southern slope of Mauna Kea small springs are perched by beds of hill wash. Dikes in the rift zones are relatively impermeable, but enclose masses of permeable rock. Water is confined at high level in the interdike compartments in Kohala Mountain, and probably in the other volcanoes. It escapes in high-level springs in the deep valleys on Kohala Mountain; some of it is recovered by tunnels. It is estimated that an average of about 13,085 million gallons of water a day falls as rain over the whole island. Of this only about 2.5 percent is visibly discharged from wells, tunnels, and springs. Large supplies of basal groundwater await development. Projects for development of additional water for the city of Hilo and the Kona District are described. Chemical analyses of water, water supplies of towns and villages, descriptions of wells, springs, and tunnels, and discharge records of numerous springs and tunnels are given in tabulated form.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 18.903688072314996° to 20.267350272759373° latitude; -156.06353759765625° to -154.80560302734375° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Harold T. Stearns, Gordon A. Macdonald. 1946. Geology and ground-water resources of the island of Hawaii. https://pubs.usgs.gov/publication/70160867

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Groundwater flow model for the Little Plover River basin in Wisconsin’s Central Sands

The Little Plover River is a groundwater-fed stream in the sand plains region of central Wisconsin. In this region, sandy sediment deposited during or soon after the last glaciation forms an important unconfined sand and gravel aquifer. This aquifer supplies water for numerous high-capacity irrigation, municipal, and industrial wells that support a thriving agricultural industry. In recent years the addition of many new wells, combined with observed diminished flows in the Little Plover and other nearby rivers, has raised concerns about the impacts of the wells on groundwater levels and on water levels and flows in nearby lakes, streams, and wetlands. Diverse stakeholder groups, including well operators, Growers, environmentalists, local land owners, and regulatory and government officials have sought a better understanding of the local groundwater-surface water system and have a shared desire to balance the water needs of the he liagricultural, industrial, and urban users with the maintenance and protection of groundwater-dependent natural resources. To help address these issues, the Wisconsin Department of Natural Resources requested that the Wisconsin Geological and Natural History Survey and U.S. Geological Survey cooperatively develop a groundwater flow model that could be used to demonstrate the relationships among groundwater, surface water, and well withdrawals and also be a tool for testing and evaluating alternative water management strategies for the central sands region. Because of an abundance of previous studies, data availability, local interest, and existing regulatory constraints the model focuses on the Little Plover River watershed, but the modeling methodology developed during this study can apply to much of the larger central sands of Wisconsin. The Little Plover River groundwater flow model simulates three-dimensional groundwater movement in and around the Little Plover River basin under steady-state and transient conditions. This model explicitly includes all high-capacity wells in the model domain and simulates seasonal variations in recharge and well pumping. The model represents the Little Plover River, and other significant streams and drainage ditches in the model domain, as fully connected to the groundwater system, computes stream base flow resulting from groundwater discharge, and routes the flow along the stream channel. A separate soil-water-balance (SWB) model was used to develop groundwater recharge arrays as input for the groundwater flow model. The SWB model uses topography, soils, land use, and climatic data to estimate recharge as deep drainage from the soil zone. The SWB model explicitly includes recharge originating as irrigation water, and computes irrigation using techniques similar to those used by local irrigation operators. The groundwater flow model uses the U.S. Geological Survey’s MODFLOW modeling code which is freely available, widely accepted, and commonly used by the groundwater community. The groundwater flow model and the SWB model use identical high-resolution numerical grids having model cells 100 feet on a side, with physical properties assigned to each grid cell. This grid allows accurate geographic placement of wells, streams, and other model features. The 3-dimensional grid has three layers; layers 1 and 2 represent the sand and gravel aquifer and layer 3 represents the underlying sandstone. The distribution of material properties in the model (hydraulic conductivity, aquifer thickness, etc.) comes from previous published geologic studies of the region, updated by calibration to recent streamflow and groundwater level data. The SWB model operates on a daily time step. The groundwater flow model was calibrated to monthly stress periods with time steps ranging from 1 to 16 days. More detailed time discretization is possible. The groundwater model was calibrated to water-level and streamflow data collected during 2013 and 2014 by adjusting model parameters (primarily hydraulic conductivity, storage, and recharge) until the model produced a conditionally optimal fit between field observations and model output, subject to consistency with previously published geologic studies. Calibration was performed under both steady and transient conditions, and used a sophisticated parameter-estimation procedure (PEST) for the calibration process and to identify important model parameters. For the Little Plover River, the two most important parameters are the global recharge multiplier and the hydraulic conductivity of the stream bed. The calibrated model produces water-level and mass-balance results that are consistent with field observations and previous studies of the area. The completed model is a powerful tool for testing and demonstrating alternative water-management scenarios. Example model applications described in this report include simulating how the cumulative impacts of pumping and land-use change have affected average baseflow in the Little Plover River. Depletion-potential mapping represents a method for predicting which wells and well locations have the greatest impact on nearby surface-water resources. The completed model is publicly available, along with a companion user’s guide to assist with its operation, at http://wgnhs.org/littleplover- river-groundwater-model.

Wisconsin

The 2016 groundwater flow model for Dane County, Wisconsin

A new groundwater flow model for Dane County, Wisconsin, replaces an earlier model developed in the 1990s by the Wisconsin Geological and Natural History Survey (WGNHS) and the U.S. Geological Survey (USGS). This modeling study was conducted cooperatively by the WGNHS and the USGS with funding from the Capital Area Regional Planning Commission (CARPC). Although the overall conceptual model of the groundwater system remains largely unchanged, the incorporation of newly acquired high-quality datasets, recent research findings, and improved modeling and calibration techniques have led to the development of a more detailed and sophisticated model representation of the groundwater system. The new model is three-dimensional and transient, and conceptualizes the county’s hydrogeology as a 12-layer system including all major unlithified and bedrock hydrostratigraphic units and two high-conductivity horizontal fracture zones. Beginning from the surface down, the model represents the unlithified deposits as two distinct model layers (1 and 2). A single layer (3) simulates the Ordovician sandstone and dolomite of the Sinnipee, Ancell, and Prairie du Chien Groups. Sandstone of the Jordan Formation (layer 4) and silty dolostone of the St. Lawrence Formation (layer 5) each comprise separate model layers. The underlying glauconitic sandstone of the Tunnel City Group makes up three distinct layers: an upper aquifer (layer 6), a fracture feature (layer 7), and a lower aquifer (layer 8). The fracture layer represents a network of horizontal bedding-plane fractures that serve as a preferential pathway for groundwater flow. The model simulates the sandstone of the Wonewoc Formation as an upper aquifer (layer 9) with a bedding-plane fracture feature (layer 10) at its base. The Eau Claire aquitard (layer 11) includes shale beds within the upper portion of the Eau Claire Formation. This layer, along with overlying bedrock units, is mostly absent in the preglacially eroded valleys along the Yahara River valley and in northeastern Dane County. Layer 12 represents the Mount Simon sandstone as the lowermost model layer. It directly overlies the Precambrian crystalline basement rock, whose top surface forms the lower boundary of the model. The model uses the USGS MODFLOW-NWT finite-difference code, a standalone version of MODFLOW-2005 that incorporates the Newton (NWT) solver. MODFLOW-NWT improves the handling of unconfined conditions by smoothing the transition from wet to dry cells. The model explicitly simulates groundwater–surface-water interaction with streamflow routing and lake-level fluctuation. Model input included published and unpublished hydrogeologic data from recent estimates of aquifer hydraulic conductivities. A spatial groundwater recharge distribution was obtained from a recent GIS-based, soil-water-balance model for Dane County. Groundwater withdrawals from pumping were simulated for 572 wells across the entire model domain, which includes Dane County and portions of seven neighboring counties—Columbia, Dodge, Green, Iowa, Jefferson, Lafayette, and Rock. These wells withdrew an average of 60 million gallons per day (mgd) over the 5-year period from 2006 through 2010. Within Dane County, 385 wells were simulated with an average withdrawal rate of 52 mgd. Model calibration used the parameter estimation code PEST, and calibration targets included heads, stream and spring flows, lake levels, and borehole flows. Steady-state calibration focused on the period 2006 through 2010; the transient calibration focused on the 7-week drought period from late May through July 2012. This model represents a significant step forward from previous work because of its finer grid resolution, improved hydrostratigraphic discretization, transient capabilities, and more sophisticated representation of surface-water features and multi-aquifer wells. Potential applications of the model include evaluation of potential sites for and impacts of new high-capacity wells, development of wellhead protection plans, evaluating the effects of changing land use and climate on groundwater, and quantifying the relationships between groundwater and surface water.

Wisconsin

Geologic framework of the Alaska Peninsula, southwest Alaska, and the Alaska Peninsula terrane

The Alaska Peninsula is composed of the late Paleozoic to Quaternary sedimentary, igneous, and minor metamorphic rocks that record the history of a number of magmatic arcs. These magmatic arcs include an unnamed Late Triassic(?) and Early Jurassic island arc, the early Cenozoic Meshik arc, and the late Cenozoic Aleutian arc. Also found on the Alaska Peninsula is one of the most complete nonmetamorphosed, fossiliferous, marine Jurassic sedimentary sections known. As much as 8,500 m of section of Mesozoic sedimentary rocks record the growth and erosion of the Early Jurassic island arc. A thinner, but still thick (as much as 5,400 m), sequence of Tertiary sedimentary rocks that are predominantly continental overlies the Mesozoic section. A brief regression in early Tertiary time on the Alaska Peninsula and granodiorite plutonism in the Shumagin, Semidi, and Sanak Islands was followed by deposition of fluvial and minor marine clastic strata. This was followed by deposition of transgressive marine clastic strata and initiation of the Meshik arc, shown by an areally extensive outpouring of volcanic and volcaniclastic rocks and debris between late Eocene and earliest Miocene time. Late Miocene time was marked by another brief transgression and northwest- to southeast-directed compression, followed by renewed volcanism and plutonism which initiated the modern Aleutian magmatic arc. Extensive glacial and glaciomarine deposits of late Pleistocene age create an extensive lowland physiographic province on the northwest side of the Alaska Peninsula and join isolated mountain masses to the Alaska Peninsula on the southwest. Multiple active volcanoes and volcanic peaks dominate the skyline of the Alaska Peninsula and represent the continuation of magmatic activity that has formed the Aleutian arc since late Miocene time. The Alaska Peninsula has had a long and involved history since Paleozoic time. We propose that the Paleozoic and Mesozoic rocks that constitute much of the Alaska Peninsula be called the Alaska Peninsula terrane. Using the concept of subterranes, we divide the terrane into two distinct but tectonically related subterranes: the Chignik and Iliamna subterranes, which share a limited common geologic history. The Iliamna subterrane has served at most times as a source area for the Chignik subterrane; however, some rock units are in common across the subterranes. The Iliamna and Chignik subterranes are in part separated by the Bruin Bay fault system. The Iliamna subterrane is composed of moderately deformed early Mesozoic marine sedimentary and volcanic rocks and schist, gneiss, and marble of Paleozoic(?) and Mesozoic age, and plutonic rocks of the Alaska-Aleutian Range batholith. Characteristic of the Chignik subterrane are little-deformed, shallow-marine to continental clastic sedimentary rocks ranging in age from Permian to latest Cretaceous. However, deep-marine, volcaniclastic, and calcareous rocks form important components of the older rocks in the subterrane. The two subterranes of the Alaska Peninsula terrane are characterized by radically different structural and metamorphic styles. The nonplutonic rocks of the Iliamna subterrane are characterized by metamorphism up to amphibolite-facies grade and intense folding. In the Chignik subterrane, the structural style is dominated by large, open, en echelon anticlinal structures, normal faulting, and thrust and high-angle reverse faults that have minor displacement in a northwest to southeast direction. In the Outer Shumagin and Sanak Islands, rocks assigned to the Chugach terrane are characterized structurally by tight, generally northeast-trending folds. Dips in these rocks tend to be steep, rarely less than 35°, and overturned beds are locally common. The boundaries separating the Alaska Peninsula terrane from other terranes are commonly indistinct or poorly defined. A few boundaries have been defined at major faults, although the extensions of these faults are speculative through some areas. The west side of the Alaska Peninsula terrane is overlapped by Tertiary sedimentary and volcanic rocks and Quaternary deposits.

Alaska