Geology Reports⌕ Search

EXPLORE THE ARCHIVE

Research about California

Source-linked reports with geographic coverage including California.

118 records · Page 3Linked to original sources
USGS2026

Recent scientific contributions by the U.S. Geological Survey in the San Francisco Bay and Sacramento–San Joaquin Delta Estuary

Introduction The San Francisco Bay and Sacramento–San Joaquin Delta Estuary (hereafter, Bay-Delta) is the largest estuary on the West Coast of the United States. The Bay-Delta covers more than 1,600 square miles and drains a watershed of more than 75,000 square miles, which is greater than 40 percent of California. The region surrounding the Bay-Delta is home to about 10 million people, and its habitats (fig. 1) support more than 800 plant and animal species. The waterways of the Bay-Delta are the central hub of California’s extensive freshwater delivery system, supplying water to more than 27 million Californians and 4 million acres of farmland in the Central Valley. The U.S. Geological Survey (USGS) is the primary science agency of the U.S. Department of the Interior, providing a broad range of Earth, water, biological, and mapping data and expertise to inform natural resource management across the country. This fact sheet focuses on research conducted by the USGS in the Bay-Delta region, mostly within the past 5 years. The fact sheet is organized across five major themes: water flow and water quality, fish and wildlife, wetland restoration, invasive species, and hazards. In each of these areas, the USGS works closely with Federal, State, and local agencies; academia; and non-governmental organizations to provide objective, evidence-based science. The data and knowledge gained from USGS research and monitoring are publicly available and are routinely used by agencies, including the U.S. Bureau of Reclamation, U.S. Army Corps of Engineers, U.S. Fish and Wildlife Service, California Department of Water Resources, California Department of Fish and Wildlife, California State Water Resources Control Board, Delta Stewardship Council, and many additional organizations and stakeholders to inform management of the Bay-Delta region and its resources.

California↗
USGS2026

Distributed faulting of the northern West Napa Fault Zone in Napa Valley, California

Mapped surface ruptures from the 24 August 2014 M w 6.0 South Napa earthquake in the Napa Valley, California, show a 2‐km‐wide zone of distributed faulting in the southern and central West Napa fault zone (WNFZ). In the northern WNFZ at Hendry Winery (HW), however, the mapped 2014 surface ruptures encompass an ∼100‐m‐wide zone, implying significant narrowing of the near‐surface fault zone to the north. We present a tomographic shear‐wave velocity ( ⁠⁠ V S ) model and guided‐wave data that indicate the northern WNFZ is at least 400‐m wide, with multiple near‐surface fault traces. Our V S model shows that the 2014 surface ruptures are underlain by discrete low‐velocity zones (LVZs), and coincident guided‐wave data show that the LVZs carry fault‐zone guided waves. If nearby (<500 m) mapped faults to the east of HW are part of the WNFZ, the entire WNFZ is more than 1 km wide in the northern Napa Valley. WNFZ guided waves travel up to 38% slower than S body waves, and low‐strain guided‐wave shaking is up to five times stronger than the associated body‐wave shaking. Our data suggest that guided waves, traveling along distributed faults, may result in an increased shaking hazard over a 1‐km‐wide area of the northern Napa Valley during future significant earthquakes. In places, the 2014 surface ruptures were difficult to find one year after the earthquake, and paleoseismic trenching showed only weak evidence for faulting, which may not have been identified in trenches if the locations of the 2014 surface ruptures had not been previously mapped ( Prentice et al. , 2015 ). Guided‐wave and V S tomography data, however, show strong evidence for faulting beneath the 2014 surface ruptures and at locations to the east. Although paleoseismic trenching is the gold standard for identifying near‐surface faulting, methods such as peak ground velocities of guided waves may better identify immature near‐surface fault traces.

California↗
USGS2026

Evaluation of water quality in the Langford Valley–Irwin Groundwater Subbasin, Fort Irwin National Training Center, California, 1993–2019

The U.S. Army Fort Irwin National Training Center (NTC), 120 miles northeast of Los Angeles in the Mojave Desert of California, obtains its potable water supply from the Bicycle Valley and Langford Valley groundwater basins; Langford Valley groundwater basin is further subdivided into the Langford Well Lake and Irwin groundwater subbasins. The Irwin groundwater subbasin contains younger, unconsolidated deposits that have a saturated thickness of as much as 200 feet (ft) and a lower aquifer within older unconsolidated deposits as thick as 650 ft. Groundwater recharge under predevelopment conditions (before 1941) occurred primarily from infiltration of intermittent streamflow in small washes that cross the Irwin groundwater subbasin. Since that time, groundwater recharge has increased because of growth of the NTC in recent years and as a result of other processes, including (1) infiltration of treated wastewater into the aquifer through ponds near the NTC wastewater treatment facility (WWTF) and (2) infiltration of imported water and treated wastewater used for landscape irrigation at base housing and athletic fields. Water samples were collected from 17 wells and analyzed for field parameters, chemical constituents, and isotope composition in the Irwin groundwater subbasin between 2014 and 2019. These data were supplemented with water-chemistry data collected during 1993–95 and at other times if available. Between 1993–95 and 2015–19, median dissolved solids and nitrate concentrations in water from wells in the Irwin groundwater subbasin increased from 620 to 1,030 milligrams per liter (mg/L) and from 2.8 to 4.5 mg/L as nitrogen, respectively. After 2014, dissolved solids and nitrate concentrations in water from wells near the NTC WWTF decreased as a result of changes in source water quality attributable to reverse osmosis of treated drinking water delivered within the Irwin groundwater subbasin and to increased levels of treatment at the NTC WWTF. Based on delta oxygen-18 and delta deuterium isotope data, increases in dissolved solids concentrations in water from most wells were consistent with evaporation prior to recharge and mobilization of soluble salts from the unsaturated zone. Arsenic and fluoride concentrations in water from wells decreased between 1993–95 and 2015–19 as the basin filled with treated wastewater, but 2015–19 concentrations generally exceeded the California State Water Resources Control Board maximum contaminant levels of 10 micrograms per liter for arsenic and 2 mg/L for fluoride. Most groundwater in the Irwin groundwater subbasin has unadjusted carbon-14 ages ranging from 18,400 to 12,350 years before present. However, water from well 10E3, located along the wash near the subbasin outflow in the southeastern part of the Irwin groundwater subbasin, contained measurable tritium, which is consistent with infiltration of intermittent streamflow and groundwater recharge from the wash after 1952. Chemical and isotopic data indicate that treated wastewater is present in water from most wells in the upper aquifer that underlies the Irwin groundwater subbasin. Wells were not sampled to adequately determine the extent of treated wastewater and changes in water quality within the lower aquifer that underlies the Irwin groundwater subbasin.

California↗
USGS2026

Assessing future hydrologic extremes using an integrated hydrology and river operations model in the Russian River watershed

Study region The Russian River watershed, situated in coastal, northern California, experiences hydrologic extremes, including periodic droughts and flooding. Water managers are working to maintain sustainable water supplies and environmental flows, while mitigating flood risks. Study focus This paper introduces an integrated hydrology and river operations model for the Russian River watershed. This model is distinct from models in previous studies because it represents surface-groundwater interactions and uses climate forcings to estimate dynamic water use demands that are superimposed onto both reservoir operations and water supply constraints. The model was used to examine three historical (1990–2015) and eight future (2016–2099) water use and climate change scenarios. New hydrological insights for the region The direct connection between streams and aquifers facilitated both annual aquifer replenishment by high winter streamflows and streamflow depletion by groundwater wells (19 % of pumped groundwater in alluvial aquifers from stream leakage) during critical low flow periods. Simulated streamflow changes included 59 % longer and 54 % more severe streamflow droughts, 26 % lower seasonal low streamflows, and up to 125 % higher peak streamflows, averaged over future climate and water use scenarios, suggesting increased future flood and water availability risks. Results showed the importance of reservoir operations for mitigating the impacts of increased hydroclimatic volatility, despite a decrease in reservoir reliability at Lake Mendocino, suggesting that reservoir management may be used to decrease future risks.

California↗
USGS2026

Complex carbonate ore mineralogy in the Mountain Pass carbonatite rare earth element deposit, USA

Economic concentrations of rare earth element (REE) minerals are uncommon in the Earth’s crust, with most occurring in carbonatites. Unlike most igneous rocks composed of silicate minerals, carbonatites are dominated by carbonate minerals, some of which can incorporate significant light REEs (LREEs; La, Ce, Pr, Nd). Technological applications of REEs are numerous and they have been identified as some of the most critical mineral commodities to the global economy. The Mountain Pass carbonatite stock in the Mojave Desert of California is the most economically significant REE deposit in the USA and contains a few to tens of percent (by volume) of the carbonate REE ore mineral bastnäsite. Despite the economic significance of the Mountain Pass deposit, studies of its ore mineralogy are limited. Here we present new carbonate ore mineralogy data for a compositionally diverse suite of carbonatitic rocks from the Mountain Pass stock and related dikes. Whole-rock geochemical data are integrated with mineral-scale textural and chemical data obtained by scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and microRaman spectroscopy. Our results document a complex spectrum of REE-bearing carbonate minerals and intermediate mixed-layer structures. Mineral species include bastnäsite [REE(CO 3 )F], hydroxylbastnäsite [REE(CO 3 )OH], parisite [Ca(REE) 2 (CO 3 ) 3 F 2 ], synchysite [Ca(REE)(CO 3 ) 2 F], röntgenite [Ca 2 (Ce,La) 3 (CO 3 ) 5 F 3 ], and sahamalite [(Mg,Fe 2+ )(REE) 2 (CO 3 ) 4 ]. Carbonate ore mineralogy is heterogeneous within and between samples, including at the intracrystal scale. Complexly zoned crystals exhibit as many as five to six different compositional domains and syntaxial intergrowths, commonly with the more Ca-rich varieties (parisite, synchysite) forming crystal rims that surround relict bastnäsite cores. We attribute the phenocryst variability to changes in the chemistry and temperature of primary carbonatite magmas and evolved/exsolved fluids. Cross-cutting vein textures of calcite, celestine and various REE carbonate minerals, interstitial bastnäsite crystallization, breccia blocks lined by fine-grained bastnäsite, and the presence of hydroxylbastnäsite and partially hydroxylated bastnäsite point to the role of secondary hydrothermal processes in REE mineralization. Fluorcarbonate mineral compositions demonstrate that La and Ce are more structurally abundant in bastnäsite, whereas the more Ca-rich species (parisite, synchysite) contain a greater proportion of REE heavier than Pr (Nd, Sm, Eu, Gd) and Y. Atomic ratios of Pr/(Nd + Pr) are likewise variable, with the highest average value for bastnäsite (0.25) compared to parisite (0.22) and sychysite (0.21). This finding has geometallurgical implications, given that current mining operations are focused on recovery of Nd and Pr for high field strength permanent magnets and the Nd/Pr ratios are a critical factor in ore processing and magnet manufacture.

California↗
USGS2026

Legacy of the fumigant 1,2-dibromo-3-chloropropane (DBCP) in California groundwater

The fumigant pesticide 1,2-dibromo-3-chloropropane (DBCP) was widely used in California agriculture during the 1960s and 1970s before being banned in 1979. Despite this ban, DBCP continues to contaminate groundwater due to its persistence and mobility. This study evaluates the distribution, historical trends, and projected persistence of DBCP in California using data from over 13,000 public supply wells and additional domestic, irrigation, and observation wells (1980-2022). Since 2010, DBCP has been detected in 9% of public supply wells statewide, with higher frequencies in the San Joaquin Valley (21%) and upper Santa Ana River watershed (13%), where DBCP use was most prevalent. Approximately 70% of wells had decreasing concentration trends, whereas increases were more common in deeper wells, indicating downward vertical migration of the DBCP front. Groundwater age estimates show that recharge timing aligns with the 1960s–1970s loading period, enabling reconstruction of peak inputs and providing a basis for age based modeling. To estimate future persistence, we applied a one dimensional advection–dispersion model that simulates long term declines in peak concentrations based on groundwater age, historical loading, and a 38 year degradation half life. Model projections suggest that concentrations above the maximum contaminant level may persist in a declining number of wells until approximately 2080 (range: 2048–2109), with longer persistence in the San Joaquin Valley. The simplified modeling framework, based on age distributions typical of wells capturing peak concentrations, can provide practical regional scale assessment of non-point source contaminants where long-term monitoring exists. This study highlights how the legacy of DBCP contamination will likely affect California's groundwater resources throughout the 21st century.

California↗
USGS2025

Effect of land cover type on 3D deformation recovery from synthetically deformed high-resolution satellite optical imagery

The limits of detection for earthquake surface deformation in the spatial domain have improved with advances in remote sensing imagery data availability, resolution, and analysis. Sub-pixel correlation and digital elevation model (DEM) differencing from sub-meter, earthquake-spanning satellite optical imagery has enhanced surface rupture mapping and deformation measurements. However, knowledge of measurement accuracy and uncertainty is limited. To address this, we construct orthophotos and digital elevation models (DEMs) from repeat high resolution (∼0.5 m) satellite optical imagery along two sections of the Garlock fault, California with clear fault geomorphology and differing land cover. We deform later sets of DEMs and images with synthetic earthquakes containing both diffuse and discrete horizontal and vertical displacements. Sub-pixel image correlation and DEM differencing demonstrate how vegetation degrades recovered displacement accuracy. In barren land cover, horizontal displacements are detectable to an expected ∼1/10th-pixel size. With shrubs, trees, and grass, detectable displacements increase to >1/2-pixel size, and filtering results by correlation score and using elevation values as input rather than image values improves accuracy. Vertical displacement detection thresholds remain lower in vegetation, at >1-pixel size. Higher slope angles degrade displacement recovery, worsened by vegetation. Diminishing seasonal separation improves accuracy over vegetated regions, though not to the level achieved in barren environments. These results will inform research and operational efforts on the utility of high resolution satellite optical imagery for detecting deformation in varied land cover. Furthermore, they reveal where alternative measurements, such as from LiDAR or radar interferometry, are required to mitigate the effects of vegetation and capture fine-scale crustal deformation.

California↗
USGS2025

Hydrogeologic characterization of the Cahuilla Valley and Terwilliger Valley Groundwater Basins, Riverside County, California

The relation between the groundwater and the amount of natural recharge to the Cahuilla Valley and Terwilliger Valley groundwater basins is not well understood. During the 20th century, the reliance on groundwater near Anza, California, used for agricultural, domestic, and municipal reasons has increased, and there is the potential for changes in groundwater availability related to climate change. Several types of existing data were evaluated, and new data were collected for this study, with the goal of characterizing the region’s hydrogeology. The study’s scope included constructing a geologic framework model to show where the groundwater-bearing units are present and their relation to each other, estimating the major components of the groundwater budget, and understanding local short-term and regional long-term groundwater flow and how that has changed since the early 1900s. Two electrical resistivity tomography surveys were done in the Durasno Valley about 2,150 feet apart to identify the thickness of the alluvium, its horizontal extent, and the depth-to-basement along two profiles perpendicular to Cahuilla Creek. The subsurface sediments were mostly horizontally layered and the transitional boundary between the alluvium and basement was thinner and shallower along the upgradient profile where the depth-to-basement was about 70 feet below land surface; the depth-to-basement at the downgradient profile was more than about 140 feet below land surface. The results from the surveys were used to place four monitoring wells at two sites along the survey profiles. Artesian flow from the deepest well at the downgradient site indicated that the decomposed and competent basement likely contributed some groundwater to the overlying alluvium, laterally, from below, or both. A digital three-dimensional geologic framework model was constructed using EarthVision software to represent the subsurface geometry of the alluvium, decomposed basement, and competent basement. Maps and cross sections of the modeled thicknesses of the alluvium and decomposed basement, and the modeled elevation of the top of the competent basement, were made to show the subsurface geometry of vertical faults, selected wells, and the groundwater-bearing units. Because natural recharge is related to the variable cycles of precipitation, estimates are difficult to quantify. Recharge and runoff have extreme interannual variability in the study area; recharge and runoff can be sporadic, and a substantive amount may not occur in some years. Estimates of recharge from a previous study and the regional-scale Basin Characterization Model for California for four different periods ranged from 3,800 acre-feet/year for 1897–1947 to 5,900 acre-feet/year for 1971–2000. Potential recharge from the disposal of domestic septic systems may have been as much as 500 acre-feet in 2020. It was estimated that between about 400 and 2,400 acre-feet/year of groundwater is lost through evapotranspiration by vegetation and evaporation from open water bodies, but the main source of discharge is through pumpage, mainly used for agriculture from the alluvium in the Cahuilla Valley and Terwilliger Valley groundwater basins. The estimated total pumpage for 1991–2021 ranged from about 1,140 acre-feet in 2019 to about 3,450 acre-feet in 1994. When summed, the cumulative amount of estimated pumpage between 1991 and 2021 was about 81,400 acre-feet. The general direction of groundwater flow is from the northeast along the San Jacinto fault zone at the headwaters of Cahuilla and Hamilton Creeks, to the surface-water outlets at the west and southeast parts of the study area. Groundwater-level data from the 1950s and earlier indicate that there was a natural groundwater divide between the Cahuilla Valley and Terwilliger Valley groundwater basins, but the changing magnitude and extent of the groundwater depressions caused by pumping since about 1950 indicate that the location of the natural groundwater boundary between the Cahuilla Valley and Terwilliger Valley groundwater basins has migrated over time. Flow from the upper to the lower parts of the Cahuilla Valley groundwater basin roughly follows the course of Cahuilla Creek through the narrow Durasno Valley where an estimated volume of flow in April 2019 was about 10–150 acre-feet/year. Short-term trends in groundwater levels, particularly in wells where groundwater is shallow and in the basement unit, show how some areas respond quickly to recharge and discharge. Wells located further to the east within the Cahuilla Valley groundwater basin in the alluvium show much less of a response to recharge events; areas of sustained pumpage from the alluvium, primarily for agriculture, show long-term declines in groundwater levels and generally do not show the effects of storm events or recent runoff. Groundwater levels in wells that are farthest from where most of the recharge occurs and where pumping has been the greatest, had some of the largest long-term groundwater-level declines at a rate of about 0.8 foot/year between 1971 and 2021.

California↗
USGS2025

Memory and jamming in fault zone sediments

Many subsurface processes involve transitions in granular material states, from arrested to creeping to flowing. Experiments and frameworks for idealized systems reveal that granular fabrics develop during shearing, co-evolve with applied stress, and govern such transitions. We use microtomography to test whether fabrics at two San Andreas fault sites reflect slip history and whether idealized frameworks extend to nature. Near-surface sediments within the fault zone transition between deformation patterns over the seismic cycle, including bulk/localized grain re-arrangements, individual grain fracturing, and localized zones of fracturing. Aseismic and co-seismic shearing produce distinct preferred grain orientations. Co-seismic fabrics can be preserved after centuries of aseismic strain, aseismic fabrics may be overprinted, and grain size and coordination number influence the fabrics. Idealized frameworks, namely anisotropic critical state theory, frictional jamming, and material memory, can explain our observations, and fault zone sediments likely undergo cycles of memory creation and erasure that influence rigidity spatiotemporally.

California↗
USGS2025

Persistent deep long-period seismicity near the Lassen Volcanic Center

Deep long-period (DLP) earthquakes have been observed at many volcanic settings around the world and linked to the magmatic processes that drive volcanic unrest. At the Lassen Volcanic Center (LVC) of the Cascade arc, limited detection of DLP activity hinders classification of anomalous seismic behavior and its relationship to the LVC magmatic system. This study uses a template matching approach with seismic data from temporary nodal and permanent stations to detect and locate DLP earthquakes near the LVC between 2017 and 2024. Within the DLP catalog of 611 events, a transition occurs from scattered (2017–2020) to oscillatory (2021–2024) occurrence rates. During the oscillatory period, regional earthquakes with large amplitude velocity waveforms observed near the LVC are associated with abrupt changes in DLP occurrence rates. Continued monitoring of DLP activity has the potential to better define the processes that drive volcanic unrest at the LVC in the future.

California↗
USGS2025

Quality of groundwater used for domestic supply in the Gilroy-Hollister basin and surrounding areas, California, 2022

More than 2 million Californians rely on groundwater from domestic wells for drinking-water supply. This report summarizes a 2022 California Groundwater Ambient Monitoring and Assessment Priority Basin Project (GAMA-PBP) water-quality survey of 33 domestic and small-system drinking-water supply wells in the Gilroy-Hollister Valley groundwater basin and the surrounding areas, where more than 20,000 residents are estimated to utilize privately owned domestic wells. The study area includes the Llagas subbasin in the north, the North San Benito subbasin in the south, and the surrounding uplands. The study was focused on groundwater resources used for domestic drinking-water supply, which are mostly drawn from shallower parts of aquifer systems rather than those of groundwater resources used for public drinking-water supply in the same area. This assessment characterized the quality of ambient groundwater in the aquifer before filtration or treatment, rather than the quality of drinking water delivered to the tap. To provide context, the measured concentrations of constituents in groundwater were compared to Federal and California State regulatory and non-regulatory benchmarks for drinking-water quality. A grid-based method was used to estimate the areal proportions of groundwater resources used for domestic drinking wells that have water-quality constituents present at high concentrations (above the benchmark), moderate concentrations (between one-half of the benchmark and the benchmark for inorganic constituents, or between one-tenth of the benchmark and the benchmark for organic constituents), and low concentrations (less than one-half or one-tenth the benchmark for inorganic and organic constituents, respectively). This method provides statistically representative results at the study-area scale and permits comparisons to other GAMA-PBP study areas. In the study area, inorganic constituents in groundwater were greater than regulatory benchmarks (U.S. Environmental Protection Agency [EPA] or State of California maximum contaminant levels [MCLs]) for public drinking-water quality in 24 percent of domestic groundwater resources. The inorganic constituents present at concentrations greater than MCLs for drinking water were nitrate (as nitrogen), barium, chromium, and selenium. Total dissolved solids (TDS) or manganese were present at concentrations greater than the secondary maximum contaminant levels (SMCLs) that the State of California uses as aesthetic-based benchmarks in 48 percent of domestic groundwater resources. No volatile organic compounds or pesticide constituents were present at concentrations greater than regulatory benchmarks. Total coliform bacteria and enterococci were detected in 4 percent of domestic groundwater resources. Per- and polyfluoroalkyl substances (PFAS) were detected in 19 percent of domestic groundwater resources, and 10 percent had concentrations greater than recently enacted (April 2024) EPA MCLs. Physical and chemical factors from natural and anthropogenic sources that could affect the groundwater quality were evaluated using results from statistical testing of associations between constituent concentrations and potential explanatory variables. In this study, relevant physical factors include well construction characteristics, groundwater age, site proximity to groundwater recharge or discharge zones, and potential sources of contamination. Relevant chemical factors include the initial chemistry of the recharge water, the mineralogy of the aquifer sediments, and the subsequent shifts in chemistry as biologic and geologic reactions alter groundwater in the subsurface. Nitrate concentrations were correlated to agricultural land use, distance from the boundary of the Gilroy-Hollister Valley groundwater basin, and the proportion of modern (post-1950s) water captured by the well. Denitrification under anoxic redox conditions can mitigate some nitrate derived from fertilizer application. Total dissolved solids primarily were derived from water-rock interactions with soils and aquifer materials in the study area, but there were high concentrations where agricultural practices contributed additional TDS. Mineralogy of aquifer sediments and rocks also affect barium, selenium, boron, and chromium concentrations in the Gilroy-Hollister Valley groundwater basin. PFAS were positively correlated with urban land use and the proportion of modern water captured by the well.

California↗
USGS2025

Long‐period ground motions from dynamic rupture simulations of large earthquakes on the creeping Hayward–Calaveras–Rodgers Creek fault system

he Hayward, Calaveras, and Rodgers Creek faults in the San Francisco Bay region of California have a high probability of producing a large earthquake in the next decades. Although these faults creep, the creep is insufficient to keep up with their relatively rapid slip rates on their deepest sections, so they have been storing tectonic strain since their last large earthquakes, with the Hayward’s and Rodgers Creek’s more than 150 yr ago. We do not know what the next large Hayward–Calaveras–Rodgers Creek earthquakes will look like or how strongly they will shake the San Francisco Bay region. Harris et al. (2021) used the 3D dynamic (spontaneous) rupture method to simulate large earthquakes on these creeping faults. In this article, we examine the resulting simulated long‐period ( T > 1 s) ground shaking from 0 to 50 km distance, for earthquakes nucleating on the Hayward fault and earthquakes nucleating on the Rodgers Creek fault. We compare these simulated long‐period ground motions with the Boore et al. (2014) well‐established empirically based ground‐motion model suitable for the slowest material velocity in our 3D velocity structure. We find that the simulated long‐period ground motions from the creeping‐fault earthquake scenarios produce a reasonable agreement with the empirical expectations if frictional cohesion is included only where it is appropriate.

California↗
USGS2025

Near-fault amplification and ground motion variability during the 2019 Ridgecrest, California sequence

We estimate ground-motion variability near the 2019 M 7.1 Ridgecrest earthquake sequence. Accurate seismic hazard estimation requires understanding ground-motion spatial correlations, yet many studies lack the dense station coverage needed to resolve small-scale variability. The 2019 M 7.1 Ridgecrest earthquake sequence presents a unique opportunity to examine ground motions and their spatial correlations at a range of interstation distances. The permanent seismic network was augmented with hundreds of temporary stations including several fault-crossing nodal arrays. We compute the event ( δE i ) and within-event ( δW ij ) residuals from the observed peak ground velocity and peak ground acceleration data to isolate potential sources of ground-motion variability. We then compare δW ij between station pairs that record an event to understand the semivariance of the ground motion versus interstation distance. By fitting an exponential model to the semivariances, we determine a correlation range of 25 km for the Ridgecrest region. Although the exponential model fits the broad-scale increase of semivariance with interstation distance, we also observe smaller-scale trends. We find that ground motions are less correlated for station pairs that are near or across faults that ruptured during the 2019 Ridgecrest sequence. We also find large, positive median δW ij with relative values 2–3 times larger than nearby stations for individual stations’ near-fault traces. Near-fault amplification and greater ground-motion variability can delineate fault zones and may locally increase the seismic hazard.

California↗
USGS2025

Aftershocks in stress shadows are inconsistent with modeled static Coulomb stress changes

Aftershock triggering is commonly attributed to increases in static Coulomb stress. In some areas, termed "stress shadows", a decrease in Coulomb stress is predicted to suppress earthquake occurrence. However, aftershocks are often observed in the modeled stress shadows. We examine several hypotheses that attempt to reconcile these shadow aftershocks with the static Coulomb stress change model: (1) they appear to be in shadows because of inaccuracy in the stress change calculations, (2) they occur on faults of unusual orientation which actually experienced increased Coulomb stress, (3) they occur on faults with different frictional properties, not modeled well by Coulomb stress, and (4) they are secondary aftershocks triggered by prior aftershocks or afterslip. When tested on the 2016 Mw7.0 Kumamoto, Japan, and 2019 Mw7.1 Ridgecrest, California, aftershock sequences, none of these hypotheses can explain the majority of the shadow aftershocks, and taken together these hypotheses can explain only about half of these aftershocks. This implies that Coulomb stress modeling that lacks small-scale fault zone heterogeneity might be inadequate to fully capture the true static stress changes and/or that other physical triggering models are needed, for example transient processes such as delayed triggering by dynamic stress changes from the passing seismic waves.

California↗
USGS2025

S/P amplitude ratios with Distributed Acoustic Sensing and application to earthquake focal mechanisms

Distributed acoustic sensing (DAS), which transforms a fiber optic cable into an array of high frequency strainmeters, has the potential to help us characterize earthquakes with a dense sampling of measurements. While earthquake focal mechanisms are frequently determined using P -wave polarities and S / P amplitude ratios with inertial seismometers, the dense sampling of DAS over potentially large portions of the focal sphere can aid our solutions. Here, we consider ∼200 regional earthquakes and thousands of S / P measurements on a DAS cable colocated with a network of inertial seismometers near Arcata, California. We demonstrate the S / P ratio measurements made on DAS are similar to those made on the inertial seismometers and can be used to constrain focal mechanism solutions.

California↗
USGS2025

SURF: An automated method for building nonplanar 3D fault models from earthquake hypocenters

Accurately characterizing 3D fault geometry is vital for improving our understanding of earthquake behavior and informing the development of seismic hazard models. Despite their importance, subsurface fault structures tend to be poorly constrained because of limitations in observational data. Improvements to the seismic networks and earthquake detection algorithms have increased the precision and volume of earthquake catalogs, which help illuminate detailed subsurface fault structure and provide the most direct information available about fault geometries at depth. We present a Python package to automate generating 3D fault geometries directly from hypocentral seismicity patterns. This method begins with clustering events based on their spatial density, identifying coherent patterns. Nearby clusters are then merged based on the similarity of their orientations. We fit nonplanar surfaces using support vector regression to balance surface accuracy with minimal deviations from planarity. The fault models are output as quadrilateral meshes at user‐defined resolution. In the process of generating the 3D fault surfaces, we compute the spatial density of seismicity around the surface and the planarity as quantitative metrics of the model outputs. As a proof of concept, we apply this approach to the San Andreas–Calaveras fault junction region and the 2019 Ridgecrest earthquake sequence, both in California, which contain complex subparallel faults well defined at the Earth’s surface and abundant microseismicity. These case studies demonstrate the method’s ability to model complex fault structures, including long continuous fault surfaces, crossing faults, variably dipping segments, and subparallel faults. We test the method on both standard network catalogs and double‐difference relocated catalogs. We find that our seismicity‐based fault model results align with published 3D models that incorporate additional constraints and interpretations ( Plesch et al. , 2020 ; Aagaard and Hirakawa, 2021 ). This workflow provides a low‐user‐input solution for estimating fault geometries at depth from earthquake catalogs.

California↗
USGS2025

Earthquake magnitude and source parameter estimation with a distributed acoustic sensing dataset in the Gorda subduction zone

Distributed acoustic sensing (DAS) systems offer a cost‐effective way to create large‐scale strainmeter arrays for seismological applications using fiber‐optic cables. DAS‐based strain measurements are known to be influenced by various factors, bringing into question their general reliability for accurate earthquake characterization. A 15‐km‐long DAS deployment in northern California was operational within 3 days of the 2022 M w 6.4 Ferndale earthquake and ran continuously throughout the aftershock sequence. We utilize these aftershock data to validate DAS‐based strain measurements in two ways. We first test the accuracy of DAS‐based magnitude estimates from peak dynamic strains by comparing them with magnitude and attenuation scaling relations derived independently from traditional borehole strainmeter (BSM) data. We demonstrate that DAS‐based magnitudes are comparable to BSM‐based magnitudes when corrections for variations in site response along the fiber‐optic cable are properly made. Magnitude errors are spatially correlated, potentially because of factors such as finite‐fault effects (e.g., stress drop) or more complex, unmodeled path attenuation or because of wave propagation effects in heterogeneous media. We then apply more advanced source characterization methodology to the DAS data using a time‐domain empirical Green’s function (EGF) deconvolution approach to measure details of the moment rate history. The EGF approach using DAS data depends on careful treatment of distorting factors such as anthropogenic sources of noise and optical phase wrapping but successfully isolates source spectra for moderate‐magnitude earthquakes: source spectral ratios obtained from DAS data, broadband seismometer data, and BSM data in the same region show consistent results, revealing differences in directivity and spectral shape among earthquakes. Although further research is needed to refine source‐time‐function estimation techniques for DAS data, particularly for larger magnitude events, these case studies demonstrate the clear potential of DAS for earthquake source characterization.

California↗