Geology topics

Roland Gritto

Publications and source records attributed to Roland Gritto.

4 recordsLinked to original sources

USGS2026

Monitoring reservoir processes at The Geysers geothermal field: Joint time-lapse acquisition and cooperative joint inversion of passive seismic and magnetotelluric data

To monitor time-lapse changes in reservoir water and steam concentrations, as well as subsurface flow in the geysers geothermal field in California, we implemented a multi-physics geophysical imaging approach. This approach utilized continuously monitored microseismic events coupled with repeat magnetotelluric (MT) observations. Travel time data from microseismic events recorded at surface stations were collected over an area of approximately 75 km² continuously from 2018 to 2023, alongside three repeat MT surveys conducted in 2021, 2022, and 2023. The resulting seismic and MT data were inverted both separately and jointly to generate time-lapse images of geophysical properties that correspond to temporal changes in water and steam saturation within the reservoir, as well as flow paths and barriers. By correlating the geophysical images with known water injection and steam production volumes, we were able to calibrate the data and gain confidence in the results, which can now be applied throughout the reservoir where borehole data are unavailable. The joint imaging results, combined with reservoir data derived from borehole observations, allow for the interpretation of temporal changes in the reservoir. This enables the operator to optimize reservoir management and their drilling program.

California↗

USGS2025

Summary of results from monitoring the Geysers with continuous passive seismic and repeat magnetotelluric measurements (2021-2023)

Understanding temporal variations in a geothermal field can support operators in decision making that pertains to optimizing production and mitigating hazards. Between 2021 and 2023, The Geysers geothermal field in northern California was monitored with an array of continuous passive seismic sensors and annual repeat magnetotelluric (MT) measurements. Each of these data sets were analyzed and modelled separately to understand the data, sensitivity, and any observable changes. Then, the data were inverted jointly using a crossgradient method to further constrain temporal changes in geophysical properties within the geothermal field. Multiple permutations of annual datasets were used as inputs to the joint inversion. Results demonstrate seismic data constrain smooth inversion of the MT data, and the MT data provide supplementary information about the location of temporal fluid changes. Estimating relative changes in steam saturation for various time intervals of the joint models shows compartmentalized changes in the field, and good spatial correlation with the location of injection wells. These results demonstrate that collecting both passive seismic and MT measurements then modeling them jointly provide complementary information and a relatively inexpensive method for monitoring temporal changes in an active geothermal field that provides results to support operators.

California↗

USGS2023

Cooperative joint inversion of magnetotelluric and microseismic data for imaging the Geysers geothermal field, California, USA

The Geysers geothermal field located in northern California, USA, is the world’s largest electricity-generating geothermal facility. To delineate the spatio-temporal distribution of reservoir steam and recharge water, we have collected microseismic and magnetotelluric (MT) data using a dense array of stations in 2021. The microseismic and MT data have been inverted together using a 3D cooperative joint inversion workflow. The joint inversion exploits a cross-gradient structural constraint because electrical conductivity structures observed in the geothermal field are strongly correlated with

California↗

USGS2014

Analysis of induced seismicity in geothermal reservoirs – An overview

In this overview we report results of analysing induced seismicity in geothermal reservoirs in various tectonic settings within the framework of the European G eothermal E ngineering I ntegrating Mitigation of Induced Se ismicity in R eservoirs (GEISER) project. In the reconnaissance phase of a field, the subsurface fault mapping, in situ stress and the seismic network are of primary interest in order to help assess the geothermal resource. The hypocentres of the observed seismic events (seismic cloud) are dependent on the design of the installed network, the used velocity model and the applied location technique. During the stimulation phase, the attention is turned to reservoir hydraulics (e.g., fluid pressure, injection volume) and its relation to larger magnitude seismic events, their source characteristics and occurrence in space and time. A change in isotropic components of the full waveform moment tensor is observed for events close to the injection well (tensile character) as compared to events further away from the injection well (shear character). Tensile events coincide with high Gutenberg-Richter b -values and low Brune stress drop values. The stress regime in the reservoir controls the direction of the fracture growth at depth, as indicated by the extent of the seismic cloud detected. Stress magnitudes are important in multiple stimulation of wells, where little or no seismicity is observed until the previous maximum stress level is exceeded (Kaiser Effect). Prior to drilling, obtaining a 3D P -wave ( Vp ) and S -wave velocity ( Vs ) model down to reservoir depth is recommended. In the stimulation phase, we recommend to monitor and to locate seismicity with high precision (decametre) in real-time and to perform local 4D tomography for velocity ratio ( Vp / Vs ). During exploitation, one should use observed and model induced seismicity to forward estimate seismic hazard so that field operators are in a position to adjust well hydraulics (rate and volume of the fluid injected) when induced events start to occur far away from the boundary of the seismic cloud.

Geothermics↗