Geology topics

Marinna A. Martini

Publications and source records attributed to Marinna A. Martini.

At least 19 recordsLinked to original sources

USGS2021

Summary of oceanographic and water-quality measurements offshore of Matanzas Inlet, Florida, 2018

U.S. Geological Survey (USGS) scientists and technical staff deployed instrumented underwater platforms and buoys to collect oceanographic and atmospheric data at two sites near Matanzas Inlet, Florida, on January 24, 2018, and recovered them on April 13, 2018. Matanzas Inlet is a natural, unmaintained inlet on the Florida Atlantic coast that is well suited to study inlet and cross-shore processes. The two study sites were located offshore of the surf zone, in 9 and 15 meters of water depth, in a line perpendicular to the coast. A sea-floor platform was deployed at each site to measure ocean currents, wave motions, acoustic and optical backscatter, temperature, salinity, and pressure. The objective was to quantify the hydrodynamic forcing for sediment transport and the response to such forcing near the seabed in the vicinity of an unmaintained inlet.

Florida↗

USGS2020

Using the Lomb-Scargle method for wave statistics from gappy time series

Sandwich Town Neck Beach in Sandwich, MA, has experienced substantial erosion and has been the subject of efforts by the town and private landowners to limit the sand loss. Erosion has been particularly dramatic in the past five years with the loss of dwellings. Sandwich's nourishment efforts presented a unique opportunity for scientists at the U.S. Geological Survey Woods Hole Coastal and Marine Science Center to monitor beach morphology and to test new technologies and techniques such as geo-referenced drone imaging. Two bottom lander deployments were performed in Cape Cod Bay at a location that was key to model the fate of waves at Sandwich Town Neck Beach and to support the study of beach morphological evolution. The study period was after the town nourished the beach and during a time when several intense winter storms reshaped the beach and removed much of the nourished sand. A TRDI Workhorse Sentinel V ADCP was used for both deployments. For wave bursts, the instruments collected 2048 samples at 2 Hz every hour. The first deployment during the winter of 2016 returned good quality data. The second deployment during the following winter had gaps throughout the time series from a wiring problem in the external battery pack. The timing of the gaps was random, the duration approximately 100 s. While most of the bursts started at the top of each hour, many had 1-3 gaps within. Time series data with random gaps are problematic for computing spectral density, and thus, wave statistics. This kind of situation is familiar in other scientific disciplines such as astrophysics [1], where techniques exist to find stationary signals in sparse data. One of these methods is the Lomb-Scargle technique for computing periodograms. The most useful feature of the Lomb-Scargle (LS) method is that it allows the spectral analysis of incomplete records, without having to manipulate the record to extrapolate from or replace missing data. We compared the effectiveness of LS against common methods of averaging Fourier transforms such as a simple un-windowed Fast Fourier transform (FFT), Welch's method, and TRDI's Wavesmon software; methods that are commonly used in oceanography for non-gappy data. Synthetic data series that have been artificially modified to introduce gaps were used to evaluate the performance of each method. The LS approach was able to recover spectral density even with several 100-s gaps present. The method was applied here to the gappy and non-gappy data from both Sandwich deployments, and wave statistics were obtained and compared to the wave-buoy data. LS was used to process data that contains gaps that was rejected by Wavesmon, which was approximately 39% of the dataset. Significant wave height and peak period from LS compared well with buoy data. Mean period computed on gappy data using LS produced values biased low, compared with other methods when gaps were filled with the mean value. The LS technique has potential to uncover low-frequency signals such as infragravity waves from gappy records where the non-gappy segments are not long enough to resolve them. It has potential to unlock new information from older data sets.

Massachusetts↗

USGS2017

Summary of oceanographic and water-quality measurements in Chincoteague Bay, Maryland and Virginia, 2014–15

U.S. Geological Survey scientists and technical support staff measured oceanographic, waterquality, seabed-elevation-change, and meteorological parameters in Chincoteague Bay, Maryland and Virginia, during the period of August 13, 2014, to July 14, 2015, as part of the Estuarine Physical Response to Storms project (GS2–2D) supported by the Department of the Interior Hurricane Sandy recovery program. These measurements provide time series data that quantify the response and can be used to better understand the resilience of this back-barrier estuarine system to storms. The Assateague Island National Seashore (National Park Service) and the Chincoteague National Wildlife Refuge (U.S. Fish and Wildlife Service) are on the east side of Chincoteague Bay.

Maryland, Virginia↗

USGS2016

Summary of oceanographic and water-quality measurements in Barnegat Bay, New Jersey, 2014–15

Scientists and technical support staff from the U.S. Geological Survey measured suspended-sediment concentrations, currents, pressure, and water temperature in two tidal creeks, Reedy Creek and Dinner Creek, in Barnegat Bay, New Jersey, from August 11, 2014, to July 10, 2015 as part of the Estuarine Physical Response to Storms project (GS2–2D). The oceanographic and water-quality data quantify suspended-sediment transport in Reedy Creek and Dinner Creek, which are part of a tidal marsh wetland complex in the Edwin B. Forsythe National Wildlife Refuge. All deployed instruments were removed between January 7, 2015, and April 14, 2015, to avoid damage by ice.

New Jersey↗

USGS2015

Coastal Change Processes Project data report for observations near Fire Island, New York, January to April 2012

An oceanographic field study during January through April 2012 investigated processes that control the sediment-transport dynamics near Fire Island, New York. This report describes the project background, field program, instrumentation configuration, and locations of the sensors deploymed. The data collected and supporting meteorological observations are presented as time series plots for data visualization. Additionally, individual, links to the database containing digital data files are available as part of this report.

New York↗

USGS2015

Coastal Change Processes Project data report for oceanographic observations near Fire Island, New York, February through May 2014

An oceanographic field study during February through May 2014 investigated processes that control the sediment-transport dynamics along the western part of Fire Island, New York. This report describes the project background, field program, instrumentation configuration, and locations of the sensors deployed. The data collected, including meteorological observations, are presented as time-series plots for data visualization. Additionally, individual links to the database containing digital data files are available as part of this report.

New York↗

USGS2015

Summary of oceanographic and water-quality measurements in Rachel Carson National Wildlife Refuge, Wells, Maine, in 2013

Suspended-sediment transport is a critical element controlling the geomorphology of tidal wetland complexes. Wetlands rely on organic material and inorganic sediment deposition to maintain their elevation relative to sea level. The U.S. Geological Survey performed observational deployments to measure suspended-sediment concentration and water flow rates in the tidal channels of the wetlands in the Rachel Carson National Wildlife Refuge in Wells, Maine. The objective was to characterize the sediment-transport mechanisms that contribute to the net sediment budget of the wetland complex. We deployed a meteorological tower, optical turbidity sensors, and acoustic velocity meters at sites on Stephens Brook and the Ogunquit River between March 27 and December 9, 2013. This report presents the time-series oceanographic and atmospheric data collected during those field studies. The oceanographic parameters include water velocity, depth, turbidity, salinity, temperature, and pH. The atmospheric parameters include wind direction, speed, and gust; air temperature; air pressure; relative humidity; short wave radiation; and photosynthetically active radiation.

Maine↗

USGS2013

Carolinas coastal change processes project data report for nearshore observations at Cape Hatteras, North Carolina

An oceanographic field study conducted in February 2010 investigated processes that control nearshore flow and sediment transport dynamics at Cape Hatteras, North Carolina. This report describes the project background, field program, instrumentation setup, and locations of the sensor deployments. The data collected, and supporting meteorological and streamflow observations, are presented as time-series plots for data visualization. Additionally, the data are available as part of this report.

North Carolina↗

USGS2012

Observations of ocean circulation and sediment transport experiment offshore of Fire Island, NY

Researchers from the U.S. Geological Survey (USGS) Woods Hole Coastal and Marine Science Center (WHCMSC), in collaboration with Coastal Carolina University (CCU) and University of South Carolina (USC), conducted a scientific field study to investigate the ocean circulation and sediment transport processes offshore of Fire Island, NY. Although the physical processes along the entire linear extent of Fire Island (~50 km) are of interest to the project, one particular region of focus is at the western end of the island where offshore sand ridges out to depths of 20 m extend across the inner shelf and connect to the near-shore bar system. The primary objective was to measure the physical processes around the sand ridges, including circulation patterns, wave parameters, bottom stress, and suspended sediment. Transects of instrumentation were positioned along and across the crests and troughs of the ridge field. A site at the top of a ridge and a site at the bottom of an adjacent trough were each populated with two tripods designed to provide high-resolution measurements near the sea-bed to record sediment re-suspension events. Measurements at these two sites include near bottom velocity profiles, acoustic Doppler velocimeters, pressure, optical transmission and backscatter at high sampling rates. Other measurements include upward looking velocity profiles, temperature, salinity, sonar images and profiles, and sediment size classes. Five smaller tripods were deployed to complete lines alongshore and across shore over a 5 km area to provide a regional picture. These tripods recorded upward looking velocity profiles and near bottom temperature, pressure and salinity. Surface buoys marked the position of the tripods and collected surface measurements at six of the sites. One buoy gathered meteorological measurements. The sites were occupied from January to April, 2012. This deployment was similar to previous efforts off Cape Hatteras, NC, in 2009, and is part of an ongoing effort to understand regional patterns in circulation and sediment transport and the interaction of inner shelf and near shore processes. New instrumentation for the USGS was introduced, including a variety of current and wave measurement equipment, acquisition and telemetry in near-realtime of the weather data, time series sonar imaging equipment, and anti-fouling wipers. Preliminary results suggest a complex and subtle relationship between wind and across shore current velocity in this region, and a more straightforward relationship between winds and alongshore currents. This paper also includes a preliminary report on the effectiveness of new measurement techniques used during this experiment.

New York↗

USGS2012

Summary of oceanographic and water-quality measurements near the Blackwater National Wildlife Refuge, Maryland, 2011

Suspended-sediment transport is a critical element governing the geomorphology of tidal marshes. Marshes rely on both organic material and inorganic sediment deposition to maintain their elevation relative to sea level. In wetlands near the Blackwater National Wildlife Refuge, Maryland, portions of the salt marsh have been subsiding relative to sea level since the early 20th century. Other portions of the marsh have been successful at maintaining elevation. The U.S. Geological Survey performed observational deployments to measure suspended-sediment concentration in the tidal channels in order to understand the magnitude of suspended-sediment concentrations, the sediment-transport mechanisms, and differences between two marsh areas, one that subsided and one that maintained elevation. We deployed optical turbidity sensors and acoustic velocity meters at multiple sites over two periods in 2011. This report presents the time-series of oceanographic data collected during those field studies, including velocity, depth, turbidity, salinity, water temperature, and pH.

Maryl↗

USGS2012

Profile measurements and data from the 2011 Optics, Acoustics, and Stress In Situ (OASIS) project at the Martha's Vineyard Coastal Observatory

This report documents data collected by the U.S. Geological Survey (USGS) for the Coastal Model Applications and Field Measurements project under the auspices of the U.S. Navy Office of Naval Research Optics, Acoustics, and Stress In Situ (OASIS) Project. The objective of the measurements was to relate optical and acoustic properties of suspended particles to changes in particle size, concentration, and vertical distribution in the bottom boundary layer near the seafloor caused by wave- and current-induced stresses. This information on the physics of particle resuspension and aggregation and light penetration and water clarity will help improve models of sediment transport, benthic primary productivity, and underwater visibility. There is well-established technology for acoustic profiling, but optical profiles are more difficult to obtain because of the rapid attenuation of light in water. A specially modified tripod with a moving arm was designed to solve this problem by moving instruments vertically in the bottom boundary layer, between the bottom and about 2 meters above the seafloor. The profiling arm was designed, built, and tested during spring and summer 2011 by a team of USGS scientists, engineers, and technicians. To accommodate power requirements and the large data files recorded by some of the optical instruments, the tripod was connected via underwater cable to the Martha's Vineyard Coastal Observatory, operated by the Woods Hole Oceanographic Institution (WHOI). This afforded real-time Internet communication with the embedded computers aboard the tripod. Instruments were mounted on the profiling arm, and additional instruments were mounted elsewhere on the tripod and nearby on the seafloor. The tripod and a small mooring for a profiling current meter were deployed on September 17, 2011, at the Martha's Vineyard Coastal Observatory 12-meter-deep underwater node about 2 kilometers south of Martha's Vineyard, Massachusetts. Divers assisted in the deployment and cleaned the instrument surfaces on the tripod approximately once per week until the tripod and current meter were recovered on October 23, 2011. There was a range of wave and current conditions during the 36-day deployment, including the distant passage of Hurricane Ophelia, several moderate wave events, and a significant local gale that generated wave heights greater than 4 meters at the 12-meter site and knocked over the tripod 3 days before it was recovered. All but one of the instruments functioned well and provided complete datasets. The details of these data and the location of files containing the best basic version of the data are described in this report.

Massachusetts↗

USGS2011

Summary of oceanographic and water–quality measurements in West Falmouth Harbor and Buzzards Bay, Massachusetts, 2009–2010

This data report presents oceanographic and water-quality observations made at six locations in West Falmouth Harbor and Buzzards Bay, Massachusetts, from August 2009 to September 2010. Both Buzzards Bay and West Falmouth Harbor are estuarine embayments; the input of freshwater on the eastern margin of Buzzards Bay adjacent to Cape Cod and West Falmouth Harbor is largely due to groundwater. In West Falmouth Harbor, the groundwater that seeps into the harbor is characterized by relatively high levels of nitrate. This high nitrate load has modified the ecology of the harbor (Howes and others, 2006) and may be a significant source of nitrate to Buzzards Bay during seasons with low biological nitrate uptake. The U.S. Geological Survey undertook these measurements to improve understanding of circulation, residence time, and water quality in the harbor and bay. We set up and monitored multiple sites in both Buzzards Bay and West Falmouth Harbor, measuring depth, water velocity,salinity, pH, dissolved oxygen, chlorophyll-a, and nitrate concentration. In this report we present the processed time-series data at these locations and provide access to the data and metadata. The results will be used to understand circulation mechanisms and verify numerical models of hydrodynamics and biogeochemistry.

Massachusetts↗

USGS2011

Carolinas Coastal Change Processes Project data report for observations near Diamond Shoals, North Carolina, January-May 2009

This Open-File Report provides information collected for an oceanographic field study that occurred during January - May 2009 to investigate processes that control the sediment transport dynamics at Diamond Shoals, North Carolina. The objective of this report is to make the data available in digital form and to provide information to facilitate further analysis of the data. The report describes the background, experimental setup, equipment, and locations of the sensor deployments. The edited data are presented in time-series plots for rapid visualization of the data set, and in data files that are in the Network Common Data Format (netcdf). Supporting observational data are also included.

North Carolina↗

USGS2010

Standard-target calibration of an acoustic backscatter system

The standard-target method used to calibrate scientific echo sounders and other scientific sonars by a single, solid elastic sphere is being adapted to acoustic backscatter (ABS) systems. Its first application, to the AQUAscat 1000, is described. The on-axis sensitivity and directional properties of transducer beams at three operating frequencies, nominally 1, 2.5, and 4 MHz, have been determined using a 10-mm-diameter sphere of tungsten carbide with 6% cobalt binder. Preliminary results are reported for the 1-MHz transducer. Their application to measurements of suspended sediment made in situ with the same device is described. This will enable the data to be expressed directly in physical units of volume backscattering.

Oceans Conference Record↗

USGS2010

High resolution near-bed observations in winter near Cape Hatteras, North Carolina

The U.S. Geological Survey (USGS) Coastal and Marine Science Center in Woods Hole, Massachusetts, is leading an effort to understand the regional sediment dynamics along the coastline of North and South Carolina. As part of the Carolinas Coastal Change Processes Project, a geologic framework study in June of 2008 by the Woods Hole Coastal and Marine Science Center's Sea Floor Mapping Group focused on the seaward limit of Diamond Shoals and provided high resolution bathymetric data, surficial sediment characteristics, and subsurface geologic stratigraphy. These data also provided unprecedented guidance to identify deployment locations for tripods and moorings to investigate the processes that control sediment transport at Diamond Shoals. Equipment was deployed at three sites from early January, 2009 through early May, 2009: north and south of the shoals at 15 m depth, and at the tip at 24 m depth. Many strong storm systems were recorded during that time period. Mounted on the tripods were instruments to measure surface waves, pressure, current velocity, bottom turbulence, suspended-sediment profiles, and sea-floor sand-ripple bedforms. Many instruments were designed and programmed to sample in high resolution in time and space, as fast as 8 Hz hourly bursts and as small as 6 cm bin sizes in near bottom profiles. A second tripod at the north site also held a visual camera system and sonar imaging system which document seafloor bedforms. The region is known for its dynamics, and one of the tripods tipped over towards the end of the experiment. A preliminary look at the data suggests the region is characterized by high energy. Raw data from a burst recorded at the south site on Mar. 26 th show instantaneous flow speed at 150 cm/s at 0.5 m above the seabed. This paper reports preliminary highlights of the observations, based on raw data, and lessons learned from a deployment of large tripod systems in such a dynamic location.

North Carolina↗

USGS2009

Long-term oceanographic observations in Massachusetts Bay, 1989-2006

This data report presents long-term oceanographic observations made in western Massachusetts Bay at long-term site A (LT-A) (42 deg 22.6' N., 70 deg 47.0' W.; nominal water depth 32 meters) from December 1989 through February 2006 and long-term site B (LT-B) (42 deg 9.8' N., 70 deg 38.4' W.; nominal water depth 22 meters) from October 1997 through February 2004 (fig. 1). The observations were collected as part of a U.S. Geological Survey (USGS) study designed to understand the transport and long-term fate of sediments and associated contaminants in Massachusetts Bay. The observations include time-series measurements of current, temperature, salinity, light transmission, pressure, oxygen, fluorescence, and sediment-trapping rate. About 160 separate mooring or tripod deployments were made on about 90 research cruises to collect these long-term observations. This report presents a description of the 16-year field program and the instrumentation used to make the measurements, an overview of the data set, more than 2,500 pages of statistics and plots that summarize the data, and the digital data in Network Common Data Form (NetCDF) format. This research was conducted by the USGS in cooperation with the Massachusetts Water Resources Authority and the U.S. Coast Guard.

Data Series↗

USGS2008

Documentation of the U.S. Geological Survey Oceanographic time-series measurement database

The U.S. Geological Survey (USGS) Oceanographic Time-Series Measurement Database contains oceanographic observations made as part of studies designed to increase understanding of sediment transport processes and associated dynamics. Analysis of these data has contributed to more accurate prediction of the movement and fate of sediments and other suspended materials in the coastal ocean. The measurements were collected primarily by investigators at the USGS Woods Hole Coastal and Marine Science Center (WHCMSC) and colleagues, beginning in 1975. Most of the field experiments were carried out on the U.S. continental shelf and slope. This report describes the instrumentation and platforms used to make the measurements; the methods used to process, apply quality-control criteria, and archive the data; the data storage format, and how the data are released and distributed. The report also includes instructions on how to access the data from the online database at http://stellwagen.er.usgs.gov/ . As of 2016, the database contains about 5,000 files, which may include observations of current velocity, wave statistics, ocean temperature, conductivity, pressure, and light transmission at one or more depths over some duration of time.

Open-File Report↗

USGS2007

Long-term performance of Aanderaa optodes and sea-bird SBE-43 dissolved-oxygen sensors bottom mounted at 32 m in Massachusetts Bay

A field evaluation of two new dissolved-oxygen sensing technologies, the Aanderaa Instruments AS optode model 3830 and the Sea-Bird Electronics, Inc., model SBE43, was carried out at about 32-m water depth in western Massachusetts Bay. The optode is an optical sensor that measures fluorescence quenching by oxygen molecules, while the SBE43 is a Clark polarographic membrane sensor. Optodes were continuously deployed on bottom tripod frames by exchanging sensors every 4 months over a 19-month period. A Sea-Bird SBE43 was added during one 4-month deployment. These moored observations compared well with oxygen measurements from profiles collected during monthly shipboard surveys conducted by the Massachusetts Water Resources Authority. The mean correlation coefficient between the moored measurements and shipboard survey data was >0.9, the mean difference was 0.06 mL L −1 , and the standard deviation of the difference was 0.15 mL L −1 . The correlation coefficient between the optode and the SBE43 was >0.9 and the mean difference was 0.07 mL L −1 . Optode measurements degraded when fouling was severe enough to block oxygen molecules from entering the sensing foil over a significant portion of the sensing window. Drift observed in two optodes beginning at about 225 and 390 days of deployment is attributed to degradation of the sensing foil. Flushing is necessary to equilibrate the Sea-Bird sensor. Power consumption by the SBE43 and required pump was 19.2 mWh per sample, and the optode consumed 0.9 mWh per sample, both within expected values based on manufacturers’ specifications.

Massachusetts↗