Geology Reports⌕ Search

Geology topics

Heather M. Bragg

Publications and source records attributed to Heather M. Bragg.

At least 19 recordsLinked to original sources

Reservoir evolution, downstream sediment transport, downstream channel change, and synthesis of geomorphic responses of Fall Creek and Middle Fork Willamette River to water years 2012–18 streambed drawdowns at Fall Creek Lake, Oregon

Executive Summary Chapter A. Introduction Fall Creek Dam impounds Fall Creek Lake, a 10-kilometer-long reservoir in western Oregon and is operated by the U.S. Army Corps of Engineers (USACE) primarily for flood-risk management (or flood control) in late autumn through early spring months, as well as for water quality, irrigation, recreation, and habitat in late spring through early autumn. Since 2011 (water year [WY] 2012), Fall Creek Lake has been temporarily drawn down each year to facilitate downstream passage of juvenile spring Chinook salmon ( Oncorhynchus tshawytscha ) through the 55-meter (m) high dam. This annual dam operation is temporary, typically lasting about 1–2 weeks from WY 2012 through 2020 (drawdown operations in WY 2022–24 have increased to more than 6 weeks). Drawdown of the reservoir results in lake levels being lowered to the elevation near the historical, pre-dam streambed. The annual streambed drawdowns of WY 2012–18 have improved fish passage and led the USACE to formally adopt streambed drawdowns as part of annual operations at Fall Creek Dam. However, temporarily lowering the lake to streambed creates free-flowing conditions in the reservoir that result in the erosion and episodic export of predominantly sand and finer-grained sediments (less than 2 millimeters [mm]) to the lower gravel-bed reaches of Fall Creek and the Middle Fork Willamette River. The introduction of large volumes of sand and finer-grain sediment into the dam-regulated reaches downstream from Fall Creek Dam prompted questions about the geomorphic responses to annual streambed drawdowns within Fall Creek Lake and downstream reaches along Fall Creek and the Middle Fork Willamette River. The U.S. Geological Survey (USGS) in partnership with USACE initiated a comprehensive geomorphic and sediment transport investigation to assess the coupled processes of reservoir erosion, sediment evacuation from Fall Creek Lake, and patterns of sediment transport and deposition in reaches downstream from the Fall Creek Dam that have resulted from annual streambed drawdowns. The purpose of this report is to systematically describe the processes of sediment erosion, transport, and deposition at Fall Creek Lake and geomorphic interactions between reaches upstream and downstream from Fall Creek Dam that relate to dam operations. Specifically, this report focuses on evaluating geomorphic responses to streambed drawdowns from WY 2012 through 2018 and placing drawdown-induced geomorphic responses within the broader context of physiographic and historical conditions and dam operations of Fall Creek and Middle Fork Willamette Rivers. Key objectives for this study were to characterize changes in reservoir morphology and substrate at Fall Creek Lake, describe the character and temporal pattern of sediment transport downstream from Fall Creek Dam, characterize geomorphic changes in channel reaches downstream from the Fall Creek Dam, and relate these data to the annual streambed drawdowns of WY 2012–18. This study uses multiple independent monitoring and measurement approaches to assess site, reach, and river-scale geomorphic responses to drawdowns to inform dam and reservoir management. Patterns and processes of reservoir evolution were assessed with geomorphic mapping and volumetric analyses of topography through comparison of multiple digital surface models (DSMs). Just downstream from Fall Creek Dam, analyses of sediment export from the reservoir focused on suspended sediment but also incorporated bedload analyses to assess sediment sizes. Geomorphic assessments downstream from the dam used reach-scale and site-scale approaches to document changes in channel morphology and substrate, including site measurements of sand and finer-grained sediment deposition and in-channel bed-material, volumetric change analyses from comparison of digital elevation models (DEMs), and repeat geomorphic mapping. Findings from this study inform river management and dam operations by providing an understanding of (1) coupled upstream-downstream geomorphic responses to the Fall Creek Lake streambed drawdowns, (2) geomorphic responses of Fall Creek Lake streambed drawdowns in comparison to drawdowns at other large dams, (3) controls on reservoir erosion and downstream geomorphic responses, and (4) implications for future hydrogeomorphic changes that may result from continued drawdowns and monitoring activities to assess those changes. Chapter B. Reservoir Morphology and Evolution Related to Dam Operations at Fall Creek Lake To understand the volume and distribution of sediment accumulation in Fall Creek Lake since dam closure in 1965, decadal-scale sedimentation patterns (spanning approximately 1965–2016) are evaluated using a combination of storage curve analyses and geomorphic mapping. Short-term (drawdown event-scale) patterns of erosion, sedimentation, and sediment export downstream are evaluated using a combination of geomorphic mapping and change detection analyses that quantify the distribution and total volume of sediment erosion and deposition within Fall Creek Lake. Geomorphic mapping of reservoir topography and analyses of historical datasets reveals four categories of landforms and sediment processes within Fall Creek Lake related to lake level operations: lacustrine sedimentation expressed in the reservoir floor, fluvial erosion and deposition within historical stream channels during streambed drawdowns, channel-like features created by erosion within the reservoir floor during streambed drawdowns, and erosion on reservoir hillslopes. Where the reservoir floor is mapped for this study as pelagic (deep water), deposition up to 3 meters (m) thick by lacustrine processes and burial of pre-dam topography with deposits thinning toward the edges of the valley floor and upstream areas of reservoir are observed. Despite over 50 years of sediment accumulation since dam construction, the main stream channels of Fall and Winberry Creeks (or reservoir thalwegs) through the reservoir are well defined, though their distinct morphology is likely influenced by a long history of recurring historical drawdowns to or near streambed since dam construction. Unregulated streamflow and sediment transport through the reservoir primarily are confined to these channels during the streambed drawdown periods. Erosional channel-like features created by drawdowns are carved through underlying, unconsolidated reservoir floor sediments and are most prominent in the lower reservoir below minimum conservation pool (the low pool elevation during winter flood season); sediment generated from the formation of these drawdown channels is more likely to be transported through and out of the reservoir than sediment deposits along the reservoir hillslopes at the valley margins that are separated from main channels by areas of low-gradient reservoir floor. Morphologic changes in the lower reservoir topography between January 2012 and November 2016 indicate overall net erosion of about 129,500 cubic meters (m 3 ). The most prominent geomorphic changes occurred along the main channels of Fall and Winberry Creeks near the Fall Creek Dam where incision, lateral migration, and slumping banks resulted in vertical and lateral adjustments to channel position, whereas most changes fell below the detectable limit on higher-elevation reservoir floor surfaces except where erosion occurred along features mapped as drawdown channels. Chapter C. Sediment Delivery from Fall Creek Lake and Transport through Downstream Reaches USGS implemented a sediment monitoring program in WY 2013–18 to evaluate the quantity and character of reservoir sediment exported from Fall Creek Lake during streambed drawdowns. Turbidity and suspended sediments were monitored annually autumn through spring to span the WY 2013–18 streambed drawdowns; however, unequal monitoring timeframes each year reduced the ability to compare results and factors affecting sediment export from the reservoir difficult between years. These data were originally measured to develop regressions and compute suspended-sediment loads (SSL). Bedload sediment monitoring from a cableway at the Fall Creek streamgage was completed in the autumn-winter of WY 2013 and 2017. The limited number of samples and presumed variability in sediment supply from the reservoir precluded construction of streamflow and bedload discharge relations to compute more than instantaneous bedload. Sand and finer-grained silts and clays were transported from the reservoir in suspension, though some coarser grains (up to 32 mm) were also mobilized and transported downstream from the dam as bedload. Observations of increased sediment transport downstream from Fall Creek Dam coincided with lake levels approaching about 3 m (10 feet [ft] or elevation 690 ft) above the streambed regulating outlets. Suspended-sediment loads computed for the full monitoring periods WY 2013–18 at the Fall Creek streamgage, located 1.4 kilometers (km) downstream from Fall Creek Dam, range from 54,700 metric tons (t) in WY 2013 to 13,900 t in WY 2018. Although the total annual SSL varied from year to year, the overall seasonal patterns of suspended sediment transport throughout each year were similar during monitoring in WY 2013-18. Suspended-sediment loads were low prior to the drawdown, then increased rapidly as lake levels lowered and approached the streambed. In the weeks following the drawdown period, as pool levels were increased, SSL remained slightly elevated above pre-drawdown levels but generally declined through the following winter and spring except during streamflow-driven pulses of suspended-sediment transport. WY 2013 had the greatest total computed SSL for each streambed drawdown and partial-year monitoring period. SSL computed for the partial-year period have generally decreased since WY 2013 and have varied by about 6,800 t with the exception of WY 2014. WY 2014 SSL reflects anomalously low sediment export due to low streamflows and freezing conditions that stabilized reservoir floor deposits. Bedload measurements in the short 1.4-km reach between Fall Creek Dam and the Fall Creek streamgage showed an inverse correlation between bedload transport rates and discharge, which probably reflects diminishing supply of coarse-sized sediment. Sand was more abundant (60–100 percent) than gravel in bedload samples confirming sand and finer-grained sediment dominated sediment evacuated from the reservoir during streambed drawdowns at Fall Creek Lake. Chapter D. Geomorphic Responses to Fall Creek Lake Streambed Drawdowns Downstream from Fall Creek Dam In the days, weeks, and months following streambed drawdown operations at Fall Creek Dam through WY 2018, sites downstream from the dam displayed a variety of geomorphic responses to reservoir sediment delivery within the main channel and overbank areas. Evaluation of streambed elevations at two streamgages located 1.4 km downstream from the dam on Fall Creek and 16.3 km downstream from the dam on the Middle Fork Willamette River indicated the effects of drawdown sediment on bed elevations were modest and transient. Repeat particle size measurements (October 2015 and September 2016) at five sites along Fall Creek and the Middle Fork Willamette River showed similar grain-sized distributions that do not reveal substantial deposition of fine-grained sediment related to the WY 2016 streambed drawdown. Altogether, these findings indicate that transport capacity in the main, low-flow channels of Fall Creek and Middle Fork Willamette River during WY 2012–18 was sufficient to mobilize and evacuate reservoir sediments from streambed drawdowns or other bank material and tributary sources. However, other monitoring for this study indicate low-velocity zones in off-channel areas are prime locations for sand and finer-grain sediment deposition. Patterns of overbank sediment accumulation indicate that the magnitude and timing of overbank deposition on bars and low-elevation floodplain varies with proximity to the dam, geomorphic setting, streamflows, and other factors. Sand and finer-grained reservoir sediments carried as suspended-sediment load in the reaches downstream from Fall Creek Dam were deposited in overbank areas as observed with clay-horizon markers during WY 2016–17. Overbank deposition quantified with Geomorphic Change Detection (GCD) software evaluated landform-scale patterns of erosion and deposition using repeat light detection and ranging (lidar) surveys at two sites in the Upper Fall Creek reach and one site in the Jasper reach for 3 years (2012–15) and one site in the Clearwater reach for 6 years (2009–15). Deposition thickness and spatial patterns from the GCD analysis were variable; some sites had dispersed but measurable deposition while at others, deposition was highly localized and exceeded 1 m in depth. Patterns of overbank deposition illustrate interactions among bar morphology, local hydraulics, and suspended-sediment transport dynamics that can create patches of highly localized deposition. The measured deposition at the two Fall Creek GCD sites likely resulted from reservoir sediments released from Fall Creek Lake during streambed drawdowns in WY 2016 and 2017 because the limited sediment inputs from bank material (geomorphically laterally stable reach) or tributaries (no significant tributaries) provided few other sediment sources. On the Middle Fork Willamette River, observed patterns of overbank deposition could reflect sediment sourced from upstream tributaries, bank erosion, or Fall Creek Lake streambed drawdown operations. Despite the introduction of several thousand tons of reservoir sediment delivered from the Fall Creek Lake streambed drawdowns to below-dam river corridors, reach-scale mapping of channel features downstream from Fall Creek Dam shows minimal evidence of changes in channel planform or landforms that can be attributed to a drawdowns in WY 2012–16. On Upper Fall Creek reach, widespread increases in gravel bars or other in-channel sediment did not result from the five streambed drawdowns. The main changes attributable to sediment releases from Fall Creek Lake were localized increases in vegetated bar area, particularly on channel margin areas where sand and finer-grain sediment was deposited and rapidly colonized by vegetation. The area of mapped secondary water features decreased between 2005 and 2016, but that may be due to lower discharges depicted in the 2016 aerial photographs and less mapped area of inundation. Primary changes along the Lower Fall Creek reach include a 6.4 percent decrease in area of secondary water features between 2011 and 2016, and a nearly twofold increase in the area of unvegetated bars. Immediately downstream from the Fall Creek confluence, there were negligible changes in the location and areas of vegetated bars and the main wetted channel between 2005 and 2016, and local increases in bar area cannot be attributed solely to deposition of reservoir sediments from Fall Creek Lake because (1) areas along the Middle Fork Willamette River just upstream from the Fall Creek confluence display similar type and magnitude of changes and (2) some of the increases at the confluence area pre-date the drawdowns. The cumulative effect of sediment releases from Fall Creek Lake streambed drawdowns from WY 2012 to 2016 on downstream channel planform and landforms are modest compared to the river-scale transformations and planform changes that occurred in the decades following dam construction. Chapter E. Discussion of Geomorphic Responses of Fall Creek and Middle Fork Willamette River to Streambed Drawdowns at Fall Creek Lake Multiple aspects of Fall Creek Dam infrastructure and operations exert first-order controls on the magnitudes of reservoir erosion that occur during the streambed drawdowns and ultimately determine the sediment delivery to downstream reaches. Key aspects of the dam and its operations that are most relevant to assessing geomorphic responses to streambed drawdowns include the (1) dam infrastructure, including configuration and size of regulating outlets and their proximity to the streambed which dictates the capacity and competence of the river to deliver sediment to downstream reaches and mode of sediment transport as suspended-sediment load or bedload; (2) frequency of historical drawdowns and long-term, year-round dam operations and lake level management, which partly dictate reservoir morphology and locations and magnitudes of readily erodible materials; (3) dam operations and hydroclimatic conditions during the streambed drawdown (including length of the drawdown and streamflows entering the reservoir), which directly control the timing, duration and magnitude of reservoir erosion and sediment evacuation; and (4) dam operations following the streambed drawdown operation that regulate streamflows (and thereby sediment transport conditions) downstream of Fall Creek Dam which primarily reflect interactions between hydroclimatic conditions and flood control operations. Patterns of sediment erosion and evacuation observed in this study at Fall Creek Lake from WY 2012–18 suggest that reservoir erosion during annual streambed drawdowns may remain similar or decrease in future years assuming (1) annual streambed drawdown operations are implemented in similar manner as the WY 2012–18 drawdowns (in terms of duration, late autumn or early winter implementation, rate of pool-level lowering to reach streambed, and other factors), (2) streambed drawdowns coincide with similar conditions as were observed WY 2012–18 (similar sediment yield into reservoir, low reservoir inflows, limited precipitation, moderate air temperature), and (3) no major geomorphic changes in the main reservoir channels of Fall and Winberry Creeks occur (for example, channel avulsion). Under such conditions, it is hypothesized that the stream channel within the reservoir would achieve a quasi-equilibrium state with respect to annual influx and export of sediment and aided by the substantial amount of in-channel bedrock, will remain laterally stable without erosion across reservoir deposits. Patterns of sediment transport measured at the Fall Creek streamgage downstream from Fall Creek Dam provide insight into the potential effects of future streambed drawdowns at Fall Creek Lake. Analyses of suspended sediment measured in WY 2013–18 show a major reduction in suspended-sediment loads between WY 2013 and later years, indicating streamflows transporting sediment through the reservoir to downstream reaches during streambed drawdowns have become supply limited. The 6-year suspended-sediment monitoring and sampling program is insufficient to make predictions about future sediment transport conditions because of uneven monitoring periods and varying controls on reservoir sediment erosion. It is likely that future suspended-sediment loads will be variable but similar to those observed in WY 2015–18 if operational, climatic, and geomorphological factors remain similar to those monitored WY 2015–18. Suspended-sediment loads downstream from Fall Creek Lake will likely remain highest when regulating outlets are fully open and Fall Creek is free flowing with the reservoir fully drained with little to no residual pool. Over time, it is possible that the suspended-sediment loads would reflect mobilization of reservoir sediment deposited in the previous year rather than erosion of sediment deposited years or decades earlier. Bedload is likely to remain a small fraction of the total sediment load evacuated from the reservoir and is relatively modest compared with pre-dam bedload transport rates because most coarse sediment remains trapped by the dam. If sediment releases from Fall Creek Lake and ensuing streamflow conditions follow a similar pattern in the future as was assessed in this study spanning WY 2012–18, near-term geomorphic adjustments downstream of the dam are expected to be modest. Barring major operational, climatic, and geomorphological changes, local site-scale deposition on bars, overbank areas, or off-channel features that persists several months after the streambed drawdown will likely continue to be highly variable, ranging from negligible to several centimeters of deposition. At the landform-scale, low velocity areas nearest to Fall Creek Dam will likely continue to undergo rapid deposition immediately during and after a streambed drawdown event, similar to patterns observed for WY 2012–18. Some of the sediment entering these off-channel features and margin areas may be temporarily stored, then later remobilized and dispersed farther downstream. But if newly deposited sediment persists through the following spring, there is a greater likelihood that local vegetation will establish, reinforce deposited material, and trap sediment during later drawdowns. The reach-scale geomorphic changes may become more apparent if (1) streambed drawdowns continued for several decades, and geomorphic changes were measured at decadal scales or (2) the amount of sediment introduced to downstream reaches substantially increased and (or) sediment transport capacity decreased. The continued streamflow regulation of Fall Creek Dam after sediment releases provides an opportunity to strategically manage streamflows during and after the streambed drawdowns to minimize downstream sediment impacts and ensure other operational thresholds are satisfied. This study provides a comprehensive foundation of datasets and geomorphic analyses to inform dam operations at Fall Creek Lake, monitor sediment transport downstream, and consider operational schemes for future drawdowns. The datasets from this study also provide baselines of sediment transport and geomorphic conditions to assess future changes in reservoir and downstream environments. Future monitoring could be tailored to address specific questions regarding the long-term geomorphic effects of streambed drawdowns on fluvial habitats, flood hazards, cultural resources, or downstream water quality. Future monitoring activities could focus on the relevant geomorphic processes and spatial domains within the three categories used for this study: (1) reservoir erosion and net sediment evacuation, (2) sediment delivery to downstream reaches, including magnitude and temporal pattern of sediment transport, and (3) geomorphic responses of downstream reaches to sediment delivery. Specifically, high priority future monitoring activities could include: Repeat topographic or photographic surveys in the reservoir to characterize changes occurring within individual drawdowns, to quantify sediment export, to determine temporal changes in reservoir storage, and to identify locations of erosion and deposition. Continuous, year-round turbidity monitoring supplemented with suspended-sediment measurements at a streamflow-gaging station immediately downstream from the dam to quantify sediment export. Repeat geomorphic monitoring, mapping, or modeling in downstream reaches to track changes in channel and over bank features using a combination of site- and reach-scale monitoring approaches. This could support assessments of sediment deposition and ensuing vegetation encroachment on flood hazards and habitats and examine how sediment transport and depositional processes may be affected by different sediment supply, streamflow, or dam management scenarios.

Oregon↗

Sediment transport, turbidity, and dissolved oxygen responses to annual streambed drawdowns for downstream fish passage in a flood control reservoir

Sediment transport, turbidity, and dissolved oxygen were evaluated during six consecutive water years (2013–2018) of drawdowns of a flood control reservoir in the upper Willamette Valley, Oregon, USA. The drawdowns were conducted to allow volitional passage of endangered juvenile chinook salmon through the dam's regulating outlets by lowering the reservoir elevation to a point where the historical streambed was exposed and transported water and sediment through the reservoir dam. Sediment loads during the drawdown were highest in the first year of monitoring, with a computed value of 40,200 metric tons over a 5-day drawdown, followed by 5 years of lower sediment loads and lower sediment transport rates, suggesting that much of the stored sediment within the reservoir thalweg was transported out of the reservoir in the early years of the consecutive drawdowns. Suspended sediment concentrations (SSC) computed using turbidity and streamflow data resulted in maximum SSC at the onset of the drawdowns, with the highest computed values occurring during the water year 2017 drawdown at 17,500 mg/L (turbidity = 2,990 FNU), and average drawdown SSC values ranging from 654 to 3,950 mg/L for the six years of monitoring. Computed SSC were on the lower range of concentrations that could be harmful to out-migrating juvenile salmon published in other studies. High amounts of particulate organic matter and sand-sized material in drawdown SSC samples affected relations between turbidity and SSC, requiring the use of multiple surrogate regression models over short time frames. Dissolved oxygen minimum values were recorded in two of the monitoring years, with a minimum value of 0.71 and 3.4 mg/L recorded at the onset of the drawdowns in water years 2016 and 2018, respectively. Dissolved oxygen values below 4 mg/L lasted for 1 h, suggesting a rapidly expressed chemical oxygen demand. The response of suspended sediment loads and SSC highlight the site-specific nature of reservoir drawdowns, and the need for evaluation of expected sediment responses for drawdowns being considered at other locations.

Oregon↗

Monitoring the effect of deep drawdowns of a flood control reservoir on sediment transport and dissolved oxygen, Fall Creek Lake, Oregon

Annual reservoir drawdowns at Fall Creek Lake, Oregon, have occurred for eight consecutive years from December 2012 to November 2019. The annual drawdowns are the result of the 2008 Biological Opinion of the US Army Corps of Engineers (USACE) Willamette Valley Project operations, which directed the USACE to carry out interim operational measures that would provide volitional downstream passage for endangered species act (ESA)-listed Chinook salmon. At Fall Creek Lake, the USACE modifies its operations by lowering the reservoir elevation to 690-ft, approximately 40 feet below the normal winter low-pool elevation. This action results in a runof-river scenario through the dam allowing juvenile Chinook salmon to safely pass through the regulating outlets. Monitoring of juvenile Chinook salmon in screw traps at the outlet of the dam has shown variable timing in out-migration associated with reservoir elevation, and that most of the juvenile fish exited the reservoir when the pool elevation passed 700-ft (Taylor and others, 2015). The annual drawdown has therefore been effective in providing safe downstream fish passage and has also had the collateral effect of transporting large quantities of suspended sediment to the downstream reaches of Fall Creek and the Middle Fork Willamette River. The US Geological Survey (USGS) has calculated time-series of suspended sediment concentrations (SSC) and suspended sediment loads (SSL) before, during, and after the drawdowns for six of the last nine drawdown years (water years [WY] 2013-2018), which have lasted between 5-14 days. The transport and deposition of sediment from the drawdowns has affected side-channel habitat below the dam by depositing large quantities of sand-size material resulting in streambed aggradation in several locations. The results from the USGS monitoring effort have provided important information to USACE on how the modification of their operations has affected sediment transport in the river reaches below the dam.

Oregon↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2015

Significant Findings An analysis of total-dissolved-gas (TDG) and water-temperature data collected at eight fixed monitoring stations on the lower Columbia River in Oregon and Washington in water year 2015 indicated the following: All but 1 of the 85 TDG sensor laboratory checks that were performed after field deployment were within ±0.5-percent saturation of a primary standard. After 3–4 weeks of deployment in the river, 79 of 89 TDG sensor field checks were within ±1.0-percent saturation of a secondary standard. Nine of the field checks greater than ±1.0-percent saturation occurred at the John Day Dam tailwater station and resulted in periods of deleted TDG data at the station. All 90 barometric pressure field checks were within ±1 millimeter of mercury of a primary stand-ard, and all 90 water-temperature field checks were within ±0.2 degrees Celsius of a secondary standard. TDG data were considered complete if received in real time and within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements, and comparison to river conditions at adjacent stations. For the eight monitoring stations, data completeness ranged from 71.9 to 99.8 percent. All quality-assurance values exceed the criteria established by the U.S. Army Corps of Engineers TDG monitoring plan. Criteria for data completeness (95-percent) were met at seven of the eight monitoring stations. Deleted data at the John Day tailwater station resulted in data completeness below criteria.

Oregon, Washington↗

Water-quality conditions and suspended-sediment transport in the Wilson and Trask Rivers, northwestern Oregon, water years 2012–14

In October 2011, the U.S. Geological Survey began investigating and monitoring water-quality conditions and suspended-sediment transport in the Wilson and Trask Rivers, northwestern Oregon. Water temperature, specific conductance, turbidity, and dissolved oxygen were measured every 15–30 minutes in both streams using real-time instream water-quality monitors. In conjunction with the monitoring effort, suspended-sediment samples were collected and analyzed to model the amount of suspended sediment being transported by each river. Over the course of the 3-year study, which ended in September 2014, nearly 600,000 tons (t) of suspended-sediment material entered Tillamook Bay from these two tributaries. Each year of the study, the Wilson River transported between 80,300 and 240,000 t of suspended sediment, while the Trask River contributed between 28,200 and 69,900 t. The suspended-sediment loads observed during the study were relatively small because streamflow conditions were routinely lower than normal between October 2011 and September 2014. Only one storm had a recurrence interval between a 2- and 5-year event. Every other storm produced streamflows equivalent to what would be classified as a 1- or 2-year event. Because most sediment moves during high flows, the lack of heavy rainfall and elevated streamflows muted any high sediment loads. Along with assessing suspended-sediment transport, the U.S. Geological Survey also monitored instream water quality. This monitoring was used to track instream conditions and relate them to water temperature, dissolved oxygen, and sedimentation issues for the Wilson and Trask Rivers. Stream temperatures in the Wilson and Trask Rivers exceeded the temperature standard for cold-water habitat. Water temperatures at both streams exceeded the standard for more than 30 percent of the year, as stream temperatures increased above the seasonal 13 degrees Celsius (°C) (seasonal core cold-water habitat) and 16 °C (salmon and steelhead [ Oncorhynchus mykiss ] spawning) thresholds. Conversely, dissolved oxygen concentrations rarely decreased to less than the absolute water-quality criterion of 8 milligrams per liter for cold-water streams. Results from this study will provide resource managers insight into the seasonality of water-quality conditions and the extent of suspended-sediment transport in the Wilson and Trask Rivers. The data are useful for establishing a baseline and for maintaining best-use land management practices and possibly for aiding in prioritization of restoration actions for both rivers and their respective watersheds.

Oregon↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2014

Significant Findings An analysis of total-dissolved-gas (TDG) and water-temperature data collected at eight fixed monitoring stations on the lower Columbia River in Oregon and Washington in water year 2014 indicated the following: All 81 TDG sensor laboratory checks that were performed after field deployment were within plus or minus (±) 0.5-percent saturation of a primary standard. After 3-4 weeks of deployment in the river, 68 of 75 TDG sensor field checks were within ±1.0-percent saturation of a secondary standard. Six of the field checks greater than ±1.0-percent saturation occurred at the John Day tailwater station, and three of these six checks resulted in periods of deleted data at the station. All 77 barometric pressure field checks were within ±1 millimeter of mercury of a primary standard, and all 74 water-temperature field checks were within ±0.2 degrees Celsius of a secondary standard. TDG data were considered complete if they were received in real time and were within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements, and comparison to river conditions at adjacent stations. For the eight monitoring stations, data completeness ranged from 78.2 to 100 percent. All quality-assurance values exceed the criteria established by the U.S. Army Corps of Engineers TDG monitoring plan. Criteria for data completeness (95 percent) were met at six of the eight monitoring stations. Deleted data at the John Day tailwater station and missed transmissions at the Camas station resulted in data completeness below criteria.

Oregon, Washington↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2013: quality-assurance data and comparison to water-quality standards

Significant Findings An analysis of total-dissolved-gas (TDG) and water-temperature data collected at eight fixed monitoring stations on the lower Columbia River in Oregon and Washington in water year 2013 indicated the following: During the spill season of April–August 2013, the averages of the 12 highest hourly TDG values in a day were periodically greater than 115-percent saturation for the forebay stations (John Day navigation lock, The Dalles forebay, and Bonneville forebay) and the Camas station. The 12 highest average daily values of TDG were also periodically greater than 120-percent saturation at Cascade Island. TDG values at the other tailwater stations (John Day Dam tailwater, The Dalles tailwater, and Warrendale) did not exceed 120-percent saturation. During parts of July, August, and September 2013, hourly water temperatures were greater than 20 degrees Celsius at all eight monitoring stations on the lower Columbia River. All of the 98 TDG sensor laboratory checks that were performed after field deployment were within ±0.5-percent saturation of a primary standard. After 3–4 weeks of deployment in the river, all but 1 of 85 TDG sensor field checks were within ±1.0-percent saturation of a secondary standard. All but 1 of 87 barometric pressure field checks were within ±1 millimeter of mercury of a primary standard, and all 86 water-temperature field checks were within ±0.2 degrees Celsius of a secondary standard. For the eight monitoring stations, a total of 99.2 percent of the TDG data were received in real time and were within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements, and comparison to river conditions at adjacent sites. Data completeness for the monitoring stations ranged from 97.7 to 100 percent. All quality-assurance and data completeness values exceed the criteria established by the U.S. Army Corps of Engineers TDG monitoring plan.

Oregon, Washington↗

Assessment of suspended-sediment transport, bedload, and dissolved oxygen during a short-term drawdown of Fall Creek Lake, Oregon, winter 2012-13

The drawdown of Fall Creek Lake resulted in the net transport of approximately 50,300 tons of sediment from the lake during a 6-day drawdown operation, based on computed daily values of suspended-sediment load downstream of Fall Creek Dam and the two main tributaries to Fall Creek Lake. A suspended-sediment budget calculated for 72 days of the study period indicates that as a result of drawdown operations, there was approximately 16,300 tons of sediment deposition within the reaches of Fall Creek and the Middle Fork Willamette River between Fall Creek Dam and the streamgage on the Middle Fork Willamette River at Jasper, Oregon. Bedload samples collected at the station downstream of Fall Creek Dam during the drawdown were primarily composed of medium to fine sands and accounted for an average of 11 percent of the total instantaneous sediment load (also termed sediment discharge) during sample collection. Monitoring of dissolved oxygen at the station downstream of Fall Creek Dam showed an initial decrease in dissolved oxygen concurrent with the sediment release over the span of 5 hours, though the extent of dissolved oxygen depletion is unknown because of extreme and rapid fouling of the probe by the large amount of sediment in transport. Dissolved oxygen returned to background levels downstream of Fall Creek Dam on December 18, 2012, approximately 1 day after the end of the drawdown operation.

Oregon↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2012: Quality-assurance data and comparison to water-quality standards

Significant Findings Air is entrained in water as it is flows through the spillways of dams, which causes an increase in the concentration of total dissolved gas in the water downstream from the dams. The elevated concentrations of total dissolved gas can adversely affect fish and other freshwater aquatic life. An analysis of total-dissolved-gas and water-temperature data collected at eight monitoring stations on the lower Columbia River in Oregon and Washington in 2012 indicated the following: During parts of the spill season of April–August 2012, hourly values of total dissolved gas (TDG) were larger than 115-percent saturation for the forebay stations (John Day navigation lock, The Dalles forebay, and Bonneville forebay) and the Camas station. Hourly values of total dissolved gas were larger than 120-percent saturation for the tailwater stations (John Day Dam tailwater, The Dalles tailwater, Cascade Island, and Warrendale). During parts of August and September 2012, hourly water temperatures were greater than 20°C (degrees Celsius) at the eight stations on the lower Columbia River. According to the State of Oregon water-temperature standard, the 7-day average of the daily maximum temperature of the lower Columbia River should not exceed 20°C; Washington regulations state that the 1-day maximum should not exceed 20°C as a result of human activities. Of the 98 laboratory TDG checks that were performed on instruments after field deployment, all were within ± 0.7-percent saturation. All but 1 of the 83 field checks of TDG sensors with a secondary standard were within ± 1.0-percent saturation after 3–4 weeks of deployment in the river. All 88 of the field checks of barometric pressure were within ±1 millimeter of mercury of a primary standard, and all 85 water-temperature field checks were within ±0.2°C of a secondary standard. For the eight monitoring stations in water year 2012, a total of 97.0 percent of the TDG data were received in real time and were within 1-percent saturation of the expected value on the ba-sis of calibration data, replicate quality-control measurements in the river, and comparison to ambient river conditions at adjacent sites. Data received from the Cascade Island site were only 77.8 percent complete because the equipment was destroyed by high water. The other stations ranged from 98.9 to 100.0 percent complete.

Oregon, Washington↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2011: Quality-assurance data and comparison to water-quality standards

Significant Findings Air is entrained in water as it is flows through the spillways of dams, which causes an increase in the concentration of total dissolved gas in the water downstream from the dams. The elevated concentrations of total dissolved gas can adversely affect fish and other freshwater aquatic life. An analysis of total-dissolved-gas and water-temperature data collected at eight monitoring stations on the lower Columbia River in Oregon and Washington in 2011 indicated the following: During the spill season of April–August 2011, hourly values of total dissolved gas (TDG) were larger than 115-percent saturation for the forebay (John Day navigation lock, The Dalles forebay, and Bonneville forebay) and Camas stations. Hourly values of total dissolved gas were larger than 120-percent saturation for the tailwater stations (John Day Dam tailwater, The Dalles tailwater, Cascade Island, and Warrendale). During parts of August and September 2011, hourly water temperatures were greater than 20°C (degrees Celsius) at the eight stations on the lower Columbia River. According to the State of Oregon water-temperature standard, the 7-day average maximum temperature of the lower Columbia River should not exceed 20°C; Washington regulations state that the 1-day maximum should not exceed 20°C as a result of human activities. Of the 79 laboratory TDG checks that were performed on instruments after field deployment, all were within ± 0.5-percent saturation and only 2 checks were out of calibration by more than 2 mm of Hg. All but 4 of the 66 field checks of TDG sensors with a secondary standard were within ± 1.0-percent saturation after 3–4 weeks of deployment in the river. All 67 of the field checks of barometric pressure were within ±1 millimeter of mercury of a primary standard, and all 66 water-temperature field checks were within ±0.2°C of a secondary standard. For the eight monitoring stations in water year 2011, a total of 93.5 percent of the TDG data were received in real time and were within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements in the river, and comparison to ambient river conditions at adjacent sites. Data received from the Cascade Island site were only 34.9% complete because the equipment was destroyed by high water. The other stations ranged from 99.6 to 100 percent complete.

Oregon, Washington↗

Geomorphic response of the Sandy River, Oregon, to removal of Marmot Dam

The October 2007 breaching of a temporary cofferdam constructed during removal of the 15-meter (m)-tall Marmot Dam on the Sandy River, Oregon, triggered a rapid sequence of fluvial responses as ~730,000 cubic meters (m 3 ) of sand and gravel filling the former reservoir became available to a high-gradient river. Using direct measurements of sediment transport, photogrammetry, airborne light detection and ranging (lidar) surveys, and, between transport events, repeat ground surveys of the reservoir reach and channel downstream, we monitored the erosion, transport, and deposition of this sediment in the hours, days, and months following breaching of the cofferdam. Rapid erosion of reservoir sediment led to exceptional suspended-sediment and bedload-sediment transport rates near the dam site, as well as to elevated transport rates at downstream measurement sites in the weeks and months after breaching. Measurements of sediment transport 0.4 kilometers (km) downstream of the dam site during and following breaching show a spike in the transport of fine suspended sediment within minutes after breaching, followed by high rates of suspended-load and bedload transport of sand. Significant transport of gravel bedload past the measurement site did not begin until 18 to 20 hours after breaching. For at least 7 months after breaching, bedload transport rates just below the dam site during high flows remained as much as 10 times above rates measured upstream of the dam site and farther downstream. The elevated sediment load was derived from eroded reservoir sediment, which began eroding when a meters-tall knickpoint migrated about 200 m upstream in the first hour after breaching. Rapid knickpoint migration triggered vertical incision and bank collapse in unconsolidated sand and gravel, leading to rapid channel widening. Over the following days and months, the knickpoint migrated upstream more slowly, simultaneously decreasing in height and becoming less distinct. Within 7 months, the knickpoint had migrated 2 km upstream from the dam site and became a riffle-like feature approximately 1 m high and a few tens of meters long. Knickpoint migration, vertical incision, and lateral erosion evacuated about 15 percent of the initial reservoir volume (125,000 m 3 ) within 60 hours following breaching, and by the end of the high flows in May 2008, about 50 percent of the volume had been evacuated. Large stormflows in November 2008 and January 2009 eroded another 6 percent of the original volume of impounded sediment. Little additional sediment eroded during the remainder of the second year following breaching. The rapid erosion of sediment by the modest flow that accompanied dam breaching was driven mainly by the steep hydraulic gradient associated with the abrupt change of base level and knickpoint formation and was aided by the unconsolidated and cohesionless character of the reservoir sediment. In the ensuing months, transport competence diminished as channel geometry evolved and the river gradient through the reservoir reach diminished. Changes in profile gradient in conjunction with channel coarsening and widening led to a rapid slowing of the rate of reservoir erosion. Sediment transport and deposition were strongly controlled by channel-gradient discontinuities and valley morphology downstream of the dam site. Those influences led to a strong divergence of sand and gravel transport and to deposition of a sediment wedge, as much as 4 m thick, that tapered to the preremoval channel bed 1.3 km downstream of the dam site. After 2 years, that deposit contained about 25 percent of the total volume of sediment eroded from the reservoir. The balance was distributed among pools within the Sandy River gorge, a narrow bedrock canyon extending 2 to 9 km downstream of the dam site, and along the channel farther downstream. A two-fraction sediment budget for the first year following breaching indicates that most of the gravel eroded from the reservoir reach was deposited within the sediment wedge and within the gorge, whereas eroded sand largely passed through the gorge and was broadly dispersed farther downstream. The sequence of transporting flows affected the specific trajectory of reservoir erosion and downstream sediment transport during the 2 years following breaching. However, because the overall erosion was largely a consequence of knickpoint retreat and channel widening, which in the 2 years after removal had affected most of the reservoir reach, it is unlikely that the specific sequence of flows significantly affected the overall outcome. Because the knickpoint had largely passed through the reservoir within 2 years, and the remaining reservoir sediment is mostly isolated high above armored or bedrock banks, it is unlikely that substantial additional sediment from the reservoir site will enter the system unless very large flows occur. Continued channel evolution downstream of the dam site is probable as deposits formed in the first 2 years are episodically mobilized. Below the Sandy River gorge, detection of effects related to release of reservoir sediment is challenging, especially in areas of sand deposition, because of the high background supply of sand in the river and substantial channel dynamism.

Oregon↗

Suspended-sediment characteristics for the Johnson Creek basin, Oregon, water years 2007-10

Significant Findings An analysis of suspended-sediment transport in the Johnson Creek basin, Oregon, during water years 2007–10 indicated that: Streamflow characteristics for the 4 years of study were not extremely dry or wet, and represented near-average conditions. Computed average annual suspended-sediment loads were 1,890 and 4,640 tons at the Gresham and Milwaukie stations, respectively. More than 70 percent of suspended-sediment transport in the watershed occurred during the high-flow months of November, December, and January. Less than 10 percent of suspended-sediment transport in the watershed occurred during April–October. About 50 percent of all suspended-sediment load is transported during the highest 1 percent of streamflows. The January 2009 streamflow peak was the third highest in the 70-year record for Johnson Creek. About 50 percent of suspended-sediment transport in water year 2009 occurred in January. The drainage area upstream of the Gresham streamflow-gaging station constitutes about 30 percent of the drainage area at the Milwaukie station, but accounted for about 40 percent of the suspended sediment and 45 percent of the streamflow at the Milwaukie station. On an annual basis, most of the higher sediment yield at the Gresham station, relative to the Milwaukie station, can be explained by the higher streamflow yield at the Gresham station rather than by higher suspended-sediment concentration.

Oregon↗

Initial fluvial response to the removal of Oregon's Marmot Dam

A temporary, 14‐meter‐high earthen cofferdam standing in place of Marmot Dam was breached on 19 October 2007, allowing the 80‐ kilometer‐long Sandy River to flow freely from Mount Hood, Oreg., to the Columbia River for the first time in nearly 100 years. Marmot Dam is one of the largest dams in the western United States (in terms of height and volume of stored sediment) to have been removed in the past 40 years, and its removal exposed approximately 730,000 cubic meters of stored sand and gravel to erosion and transport by the newly energetic mountain river. At the time, its breach represented the greatest release of sediment from any U.S. dam removal. (The March 2008 breaching of Montana's Milltown Dam exposed about 5–10 times as much sediment to potential erosion.)

Oregon↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2010: Quality-assurance data and comparison to water-quality standards

Significant Findings When water is released through the spillways of dams, air is entrained in the water, increasing the downstream concentration of dissolved gases. Excess dissolved-gas concentrations can have adverse effects on freshwater aquatic life. The U.S. Geological Survey (USGS), in cooperation with the U.S. Army Corps of Engineers, collected dissolved-gas and water-temperature data at eight monitoring stations on the lower Columbia River in Oregon and Washington in 2010. Significant findings from the data include: During the spill season of April through August 2010, hourly values of total dissolved gas (TDG) were occasionally larger than 115-percent saturation for the forebay stations (John Day navigation lock, The Dalles forebay, Bonneville forebay, and Camas). Hourly values of total dissolved gas were occasionally larger than 120-percent saturation for four tailwater stations (John Day Dam tailwater, The Dalles tailwater, Cascade Island, and Warrendale). From late July to late August or early September 2010, hourly water temperatures were greater than 20°C (degrees Celsius) at the eight stations on the lower Columbia River. According to the State of Oregon temperature standard, the 7-day average maximum temperature of the lower Columbia River should not exceed 20°C Washington regulations state that the 1-day maximum should not exceed 20°C as a result of human activities. All 105 laboratory checks of the TDG sensors (without the membrane attached) with a certified pressure gage were within ± (plus or minus) 0.5 percent saturation after 3 to 4 weeks of deployment in the river. All but 1 of the 85 in situ field checks of TDG sensors with a secondary standard were within ± 2.0-percent saturation after 3-4 weeks of deployment in the river. All 88 of the field checks of barometric pressure were within ± 1 millimeter of mercury of a primary standard, and all 87 water-temperature field checks were within ± 0.2 ° C of a secondary standard. For the eight monitoring stations in water year 2010, a total of 99.7 percent of the TDG data were received in real time and were within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements in the river, and comparison to ambient river conditions at adjacent stations. Data received from the individual stations ranged from 98.4 to 100.0 percent complete.

Oregon, Washington↗

Water-quality in the North Santiam River Basin, Oregon— Comparison of water-quality data for water year 2007 with the preceding period of record

Water-quality data have been collected in the North Santiam River basin since 1998. During water year 2007, eight monitoring stations were operated throughout the basin. Streamflow data were collected at all but one of these sites. This report presents a comparison of the water-quality and streamflow data collected at each monitoring station from monitor installation through water year 2006 with the data for water year 2007. Data were compiled monthly and annually to identify extreme values by season and for entire periods of study.

Oregon↗

Total dissolved gas and water temperature in the lower Columbia River, Oregon and Washington, water year 2009: Quality-assurance data and comparison to water-quality standards

Significant Findings When water is released through the spillways of dams, air is entrained in the water, increasing the downstream concentration of dissolved gases. Excess dissolved-gas concentrations can have adverse effects on freshwater aquatic life. The U.S. Geological Survey (USGS), in cooperation with the U.S. Army Corps of Engineers, collected dissolved-gas and water-temperature data at eight monitoring stations on the lower Columbia River in Oregon and Washington in 2009. Significant findings from the data include: During the spill season of April through August 2009, hourly values of total dissolved gas (TDG) were occasionally larger than 115-percent saturation for the forebay stations (John Day navigation lock, The Dalles forebay, Bonneville forebay, and Camas). Hourly values of total dissolved gas were occasionally larger than 120-percent saturation for two tailwater stations (John Day Dam tailwater and Cascade Island). From mid- to late July to mid-September 2009, water temperatures were greater than 20°C (degrees Celsius) at seven stations on the lower Columbia River. According to the State of Oregon temperature standard, the 7-day average maximum temperature of the lower Columbia River should not exceed 20°C; Washington regulations state that the 1-day maximum should not exceed 20°C as a result of human activities. All 96 laboratory checks of the TDG sensors with a certified pressure gage were within 0.4 percent saturation after 3 to 4 weeks of deployment in the river. All but 2 of the 73 in situ field checks of TDG sensors with a secondary standard were within ± (plus or minus) 1.0-percent saturation after 3-4 weeks of deployment in the river. All 74 of the field checks of barometric pressure were within ±2.0 millimeters of mercury of a secondary standard, and all 65 water-temperature field checks were within ±0.2°C. For the eight monitoring stations in water year 2009, a total of 99.2 percent of the TDG data were received in real time by the USGS satellite downlink and were within 1-percent saturation of the expected value on the basis of calibration data, replicate quality-control measurements in the river, and comparison to ambient river conditions at adjacent sites. Data received from the individual stations ranged from 97.0 to 100.0 percent complete.

Oregon, Washington↗

Suspended-Sediment Budget for the North Santiam River Basin, Oregon, Water Years 2005-08

Significant Findings An analysis of sediment transport in the North Santiam River basin during water years 2005-08 indicated that: Two-thirds of sediment input to Detroit Lake originated in the upper North Santiam River subbasin. Two-thirds of the sediment transported past Geren Island originated in the Little North Santiam River subbasin. The highest annual suspended-sediment load at any of the monitoring stations was the result of a debris flow on November 6, 2006, on Mount Jefferson. About 86 percent of the total sediment input to Detroit Lake was trapped in the lake, whereas 14 percent was transported farther downstream. More than 80 percent of the sediment transport in the basin was in November, December, and January. The variance in the annual suspended-sediment loads was better explained by the magnitude of the annual peak streamflow than by the annual mean streamflow.

Scientific Investigations Report↗

Evolving fluvial response of the Sandy River, Oregon, following removal of Marmot Dam

The October 2007 removal of Marmot Dam on the Sandy River, Oregon, triggered a rapid sequence of fluvial responses as ~730,000 m3 of sand and gravel that filled the former reservoir were suddenly exposed to an energetic river. Using direct measurements of sediment transport, photogrammetry, and repeat surveys between transport events, we monitored the erosion, transport, and redeposition of this sediment in the hours, days, and months following breaching. Measurements of suspended load and bedload documented an initial spike in the flux of fine suspended sediment in the minutes after breaching followed by high rates of suspendedand bedload transport of sand. Significant gravel transport did not begin at a measurement site 0.4 km downstream of the dam until 18–20 hours after breaching, when bedload transport achieved rates of about 60 kg/s—rates that greatly exceeded concurrent measurements of less than 10 kg/s at sites upstream and farther downstream of the dam. Bedload transport rates just below the dam site remained 10–100 times above upstream and downstream rates through subsequent high flow events during the winter and spring of 2007 and 2008. Much of the elevated sediment load was derived from eroded reservoir sediment, which initially began eroding when a multi-meter-tall knickpoint migrated upstream 200 meters in the first hour. Rapid knickpoint migration triggered bank collapse in the unconsolidated fill, which swiftly widened the channel. Over the following days and months, the knickpoint migrated slowly upchannel, simultaneously lowering and becoming less distinct. By May 2008, a riffle-like feature approximately 1 m high, a few tens of meters long, and 2 km upstream from the breached dam persisted. Knickpoint and lateral erosion evacuated ~100,000 cubic meters of sediment from the reservoir in the first 60 hours, and by the end of high flows in May 2008 about 350,000 cubic meters (45 percent of the initial reservoir volume) had been evacuated. Large stormflows in November 2008 and January 2009 eroded another 39,000 cubic meters of sediment. Thus, within 15 months of breaching, about 55 percent of the impounded sediment (390,000 cubic meters) had been eroded. Two years after breaching, only another 10,000 m3 (~400,000 m3 total) had been eroded. About 30 percent of the eroded sediment has been redeposited in a tapered wedge of sediment that extends 2 km from the former dam site to the entrance of a confined bedrock gorge. Much of the balance of the eroded sediment is distributed along and partly fills pools within the Sandy River gorge, a narrow bedrock canyon extending 2–9 km downstream of the former dam site, and along the channel farther downstream.

Oregon↗