Geology topics

David A.V. Eckhardt

Publications and source records attributed to David A.V. Eckhardt.

12 recordsLinked to original sources

USGS2012

An assessment of radon in groundwater in New York State

Abstract: A set of 317 samples collected from wells throughout New York State (excluding Long Island) from 2003 through 2008 was used to assess the distribution of radon gas in drinking water. Previous studies have documented high concentrations of radon in groundwater from granitic and metamorphic bedrock, but there have been only limited characterizations of radon in water from sedimentary rock and unconsolidated sand-and-gravel deposits in New York. Approximately 8% of the samples from bedrock wells exceed 89 Bq L -1 (eight times the proposed regulatory limit), but only 2% of samples from sand-and-gravel wells exceed 44 Bq L -1 . Specific metamorphic and sedimentary rock formations in New York are associated with the high radon concentrations, indicating that specific areas of New York could be targeted with efforts to reduce the risk of exposure to radon in groundwater. Additionally, radon in groundwater from the sand-and-gravel aquifers was found to be directly correlated to radon in indoor air when assessed by county.

New York↗

USGS2012

Baseline groundwater quality in national park units within the Marcellus and Utica Shale gas plays, New York, Pennsylvania, and West Virginia, 2011

Groundwater samples were collected from 15 production wells and 1 spring at 9 national park units in New York, Pennsylvania, and West Virginia in July and August 2011 and analyzed to characterize the quality of these water supplies. The sample sites generally were selected to represent areas of potential effects on water quality by drilling and development of gas wells in Marcellus Shale and Utica Shale areas of the northeastern United States. The groundwater samples were analyzed for 53 constituents, including nutrients, major inorganic constituents, trace elements, chemical oxygen demand, radioactivity, and dissolved gases, including methane and radon-222. Results indicated that the groundwater used for water supply at the selected national park units is generally of acceptable quality, although concentrations of some constituents exceeded at least one drinking-water guideline at several wells. Nine analytes were detected in concentrations that exceeded Federal drinking-water standards, mostly secondary standards that define aesthetic properties of water, such as taste and odor. One sample had an arsenic concentration that exceeded the U.S. Environmental Protection Agency maximum contaminant level (MCL) of 10 micrograms per liter (μg/L). The pH, which is a measure of acidity (hydrogen ion activity), ranged from 4.8 to 8.4, and in 5 of the 16 samples, the pH values were outside the accepted U.S. Environmental Protection Agency secondary maximum contaminant level (SMCL) range of 6.5 to 8.5. The concentration of total dissolved solids exceeded the SMCL of 500 milligrams per liter (mg/L) at four sites. The sulfate concentration exceeded the SMCL of 250 mg/L concentration in one sample, and the fluoride concentration exceeded the SMCL of 2 mg/L in one sample. Sodium concentrations exceeded the U.S. Environmental Protection Agency drinking water health advisory of 60 mg/L at four sites. Iron concentrations exceeded the SMCL of 300 μg/L in two samples, and manganese concentrations exceeded the SMCL of 50 μg/L in five samples. Radon-222 concentrations exceeded the proposed U.S. Environmental Protection Agency MCL of 300 picocuries per liter in eight samples.

New York;Pennsylvania;West Virginia↗

USGS2011

Geophysical, stratigraphic, and flow-zone logs of selected wells in Cayuga County, New York, 2001–2011

Geophysical logs were collected and analyzed along with bedrock core samples and bedrock outcrops to define the bedrock stratigraphy and flow zones penetrated by 93 monitor and water-supply wells in Cayuga County, New York. The work was completed from 2001 through 2011 as part of an investigation of volatile-organic compound contamination in the carbonate-bedrock aquifer system between Auburn and Union Springs. The borehole logs included gamma, caliper, wellbore image, fluid property, and flow logs. The log information was used with bedrock core samples to define the regional stratigraphy, evaluate flow zones within the bedrock aquifers, and develop and implement a multilevel monitoring design for groundwater levels and water quality within the study area.

New York↗

USGS2010

Geophysical Logs of Selected Wells at the Diaz Chemical Superfund Site in the Village of Holley, New York, 2009

Geophysical logs were collected and analyzed to define the bedrock fracture patterns and flow zones penetrated by three wells at the Diaz Chemical Superfund Site in the Village of Holley in Orleans County, New York. The work was conducted in December 2009 as part of the investigation of contamination by organic compounds in the shale, mudstone, and sandstone bedrock at the Site. The geophysical logs include natural-gamma, caliper, borehole image, fluid properties, and flowmeter data. The orientation of fractures in the boreholes was inferred from the log data and summarized in stereo and tadpole plots; when possible, the transmissivity and hydraulic head was also determined for fracture zones that were observed to be hydraulically active through the flowmeter logs. The data are intended, in part, for use in the remediation of the site.

Data Series↗

USGS2010

Water resources of Monroe County, New York, water years 2003-08: Streamflow, constituent loads, and trends in water quality

This report, the sixth in a series published since 1994, presents analyses of hydrologic data in Monroe County for the period October 2002 through September 2008. Streamflows and water quality were monitored at nine sites by the Monroe County Department of Health and the U.S. Geological Survey. Streamflow yields (flow per unit area) were highest in Northrup Creek, which had sustained flows from year-round inflow from the village of Spencerport wastewater-treatment plant and seasonal releases from the New York State Erie (Barge) Canal. Genesee River streamflow yields also were high, at least in part, as a result of higher rainfall and lower evapotranspiration rates in the upper part of the Genesee River Basin than in the other study basins. The lowest streamflow yields were measured in Honeoye Creek, which reflected a decrease in flows due to the withdrawals from Hemlock and Canadice Lakes for the city of Rochester water supply. Water samples collected at nine monitoring sites were analyzed for nutrients, chloride, sulfate, and total suspended solids. The loads of constituents, which were computed from the concentration data and the daily flows recorded at each of the monitoring sites, are estimates of the mass of the constituents that was transported in the streamflow. Annual yields (loads per unit area) also were computed to assess differences in constituent transport among the study basins. All urban sites - Allen Creek and the two downstream sites on Irondequoit Creek - had seasonally high concentrations and annual yields of chloride. Chloride loads are attributed to the application of road-deicing salts to the county's roadways and are related to population and road densities. The less-urbanized sites in the study - Genesee River, Honeoye Creek, and Oatka Creek - had relatively low concentrations and yields of chloride. The highest concentrations and yields of sulfate were measured in Black Creek, Oatka Creek, and Irondequoit Creek at Railroad Mills and are attributable to dissolution of sulfate from gypsum (calcium sulfate) deposits in Silurian shale bedrock that crops out upstream from these monitoring sites. Northrup Creek had the highest concentrations of phosphorus, orthophosphate, and nitrogen, and high yields of nitrate plus nitrite nitrogen and ammonia plus organic nitrogen. These results are attributed to discharges from the Spencerport wastewater-treatment plant (which ceased operation in June 2008), diversions from the New York State Erie (Barge) Canal, and manure and fertilizers applied to agricultural fields. Concentrations and yields of nitrate plus nitrite nitrogen also were high in Oatka Creek and Black Creek; basins with substantial agricultural land uses. Allen Creek had the second highest yield of ammonia plus organic nitrogen. Honeoye Creek, which drains a relatively undeveloped basin, had the lowest yields of nitrogen constituents. The second highest median concentrations and highest sample concentrations of phosphorus and orthophosphate, as well as the highest phosphorus yields, were measured in the Genesee River. A comparison of the yields computed for the two downstream sites on Irondequoit Creek - above Blossom Road and at Empire Boulevard - permitted an assessment of the mitigative effects of the Ellison Park wetland on constituent loads, which would otherwise be transported to Irondequoit Bay. These effects also include those provided by a flow-control structure (installed mid-way through the wetland during February 1997), which was designed to increase the dispersal and short-term detention of stormflows in the wetland. The wetland decreased yields of particulate constituents - phosphorus and ammonia plus organic nitrogen - but had little effect on the yields of dissolved constituents - chloride, sulfate, and nitrate plus nitrite nitrogen. Trends in flow-adjusted concentrations were identified at all sites for most of the nutrient constituents that were evaluated. All of the linear time tren

Scientific Investigations Report↗

USGS2009

Groundwater Quality in Central New York, 2007

Water samples were collected from 7 production wells and 28 private residential wells in central New York from August through December 2007 and analyzed to characterize the chemical quality of groundwater. Seventeen wells are screened in sand and gravel aquifers, and 18 are finished in bedrock aquifers. The wells were selected to represent areas of greatest groundwater use and to provide a geographical sampling from the 5,799-square-mile study area. Samples were analyzed for 6 physical properties and 216 constituents, including nutrients, major inorganic ions, trace elements, radionuclides, pesticides, volatile organic compounds, phenolic compounds, organic carbon, and 4 types of bacteria. Results indicate that groundwater used for drinking supply is generally of acceptable quality, although concentrations of some constituents or bacteria exceeded at least one drinking-water standard at several wells. The cations detected in the highest concentrations were calcium, magnesium, and sodium; anions detected in the highest concentrations were bicarbonate, chloride, and sulfate. The predominant nutrients were nitrate and ammonia, but no nutrients exceeded Maximum Contaminant Levels (MCLs). The trace elements barium, boron, lithium, and strontium were detected in every sample; the trace elements present in the highest concentrations were barium, boron, iron, lithium, manganese, and strontium. Fifteen pesticides, including seven pesticide degradates, were detected in water from 17 of the 35 wells, but none of the concentrations exceeded State or Federal MCLs. Sixteen volatile organic compounds were detected in water from 15 of the 35 wells. Nine analytes and three types of bacteria were detected in concentrations that exceeded Federal and State drinking-water standards, which typically are identical. One sample had a water color that exceeded the U.S. Environmental Protection Agency (USEPA) Secondary Maximum Contaminant Level (SMCL) and the New York State MCL of 10 color units. Sulfate concentrations exceeded the USEPA SMCL and the New York State MCL of 250 milligrams per liter (mg/L) in two samples, and chloride concentrations exceeded the USEPA SMCL and the New York State MCL of 250 mg/L in two samples. Sodium concentrations exceeded the USEPA Drinking Water Health Advisory of 60 mg/L in eight samples. Iron concentrations exceeded the USEPA SMCL and the New York State MCL of 300 micrograms per liter (ug/L) in 10 filtered samples. Manganese exceeded the USEPA SMCL of 50 ug/L in 10 filtered samples and the New York State MCL of 300 ug/L in 1 filtered sample. Barium exceeded the MCL of 2,000 ug/L in one sample, and aluminum exceeded the SMCL of 50 ug/L in three samples. Radon-222 exceeded the proposed USEPA MCL of 300 picocuries per liter in 12 samples. One sample from a private residential well had a trichloroethene concentration of 50.8 ug/L, which exceeded the MCL of 5 ug/L. Any detection of coliform bacteria indicates a potential violation of New York State health regulations; total coliform bacteria were detected in 19 samples, and fecal coliform bacteria were detected in one sample. The plate counts for heterotrophic bacteria exceeded the MCL (500 colony-forming units per milliliter) in three samples.

Open-File Report↗

USGS2009

Water-Quality Characterization of Surface Water in the Onondaga Lake Basin, Onondaga County, New York, 2005-08

Water-resources managers in Onondaga County, N.Y., have been faced with the challenge of improving the water-quality of Onondaga Lake. To assist in this endeavor, the U.S. Geological Survey undertook a 3-year basinwide study to assess the water quality of surface water in the Onondaga Lake Basin. The study quantified the relative contributions of nonpoint sources associated with the major land uses in the basin and also focused on known sources (streams with large sediment loads) and presumed sinks (Onondaga Reservoir and Otisco Lake) of sediment and nutrient loads, which previously had not been evaluated. Water samples were collected and analyzed for nutrients and suspended sediment at 26 surface-water sites and 4 springs in the 285-square-mile Onondaga Lake Basin from October 2005 through December 2008. More than 1,060 base-flow, stormflow, snowmelt, spring-water, and quality-assurance samples collected during the study were analyzed for ammonia, nitrite, nitrate-plus-nitrite, ammonia-plus-organic nitrogen, orthophosphate, phosphorus, and suspended sediment. The concentration of total suspended solids was measured in selected samples. Ninety-one additional samples were collected, including 80 samples from 4 county-operated sites, which were analyzed for suspended sediment or total suspended solids, and 8 precipitation and 3 snowpack samples, which were analyzed for nutrients. Specific conductance, salinity, dissolved oxygen, and water temperature were periodically measured in the field. The mean concentrations of selected constituents in base-flow, stormflow, and snowmelt samples were related to the land use or land cover that either dominated the basin or had a substantial effect on the water quality of the basin. Almost 40 percent of the Onondaga Lake Basin is forested, 30 percent is in agricultural uses, and almost 21 percent, including the city of Syracuse, is in developed uses. The data indicated expected relative differences among the land types for concentrations of nitrate, ammonia-plus-organic nitrogen, and orthophosphate. The data departed from the expected relations for concentrations of phosphorus and suspended sediment, and plausible explanations for these departures were posited. Snowmelt concentrations of dissolved constituents generally were greater and those of particulate constituents were less than concentrations of these constituents in storm runoff. Presumably, the snowpack acted as a short-term sink for dissolved constituents that had accumulated from atmospheric deposition, and streambed erosion and resuspension of previously deposited material, rather than land-surface erosion, were the primary sources of particulate constituents in snowmelt flows. Longitudinal assessments documented the changes in the median concentrations of constituents in base flows and event flows (combined stormflow and snowmelt) from upstream to downstream monitoring sites along the two major tributaries to Onondaga Lake - Onondaga Creek and Ninemile Creek. Median base-flow concentrations of ammonia and phosphorus and event concentrations of ammonia increased in the downstream direction in both streams. Whereas median event concentrations of other constituents in Onondaga Creek displayed no consistent trends, concentrations of ammonia-plus-organic nitrogen, orthophosphate, phosphorus, and suspended sediment in Ninemile Creek decreased from upstream to downstream sites. Springs discharging from the Onondaga and Bertie Limestone had measureable effects on water temperatures in the receiving streams and increased salinity and values of specific conductance in base flows. Loads of selected nutrients and suspended sediment transported in three tributaries of Otisco Lake were compared with loads from 1981-83. Loads of ammonia-plus-organic nitrogen and orthophosphate decreased from 1981-83 to 2005-08, but those of nitrate-plus-nitrite, phosphorus, and suspended sediment increased. The largest load increase was for suspende

Scientific Investigations Report↗

USGS2008

Ground-Water Quality in Western New York, 2006

Water samples were collected from 7 production wells and 26 private residential wells in western New York from August through December 2006 and analyzed to characterize the chemical quality of ground water. Wells at 15 of the sites were screened in sand and gravel aquifers, and 18 were finished in bedrock aquifers. The wells were selected to represent areas of greatest ground-water use and to provide a geographical sampling from the 5,340-square-mile study area. Samples were analyzed for 5 physical properties and 219 constituents that included nutrients, major inorganic ions, trace elements, radionuclides, pesticides, volatile organic compounds (VOC), phenolic compounds, organic carbon, and bacteria. Results indicate that ground water used for drinking supply is generally of acceptable quality, although concentrations of some constituents or bacteria exceeded at least one drinking-water standard at 27 of the 33 wells. The cations that were detected in the highest concentrations were calcium, magnesium, and sodium; anions that were detected in the highest concentrations were bicarbonate, chloride, and sulfate. The predominant nutrients were nitrate and ammonia; nitrate concentrations were higher in samples from sand and gravel aquifers than in samples from bedrock. The trace elements barium, boron, copper, lithium, nickel, and strontium were detected in every sample; the trace elements with the highest concentrations were barium, boron, iron, lithium, manganese, and strontium. Eighteen pesticides, including 9 pesticide degradates, were detected in water from 14 of the 33 wells, but none of the concentrations exceeded State or Federal Maximum Contaminant Levels (MCLs). Fourteen volatile organic compounds were detected in water from 12 of the 33 wells, but none of the concentrations exceeded MCLs. Eight chemical analytes and three types of bacteria were detected in concentrations that exceeded Federal and State drinking-water standards, which are typically identical. Sulfate concentrations exceeded the U.S. Environmental Protection Agency (USEPA) Secondary Maximum Contaminant Level (SMCL) of 250 milligrams per liter (mg/L) in three samples, and chloride concentrations exceeded the SMCL of 250 mg/L in two samples. Sodium concentrations exceeded the USEPA Drinking Water Health Advisory of 60 mg/L in nine samples. Iron concentrations exceeded the SMCL of 300 ug/L (micrograms per liter) in 14 filtered samples, and manganese exceeded the USEPA SMCL of 50 ug/L in 15 filtered samples, as well as the New York State MCL of 300 ug/L in 1 filtered sample. Arsenic exceeded the USEPA MCL of 10 ug/L in two samples, aluminum exceeded the SMCL for aluminum of 50 ug/L in one sample, and lead exceeded the MCL of 15 ug/L in one sample. Radon-222 exceeded the proposed USEPA MCL of 300 picocuries per liter in 24 samples. Any detection of coliform bacteria indicates a violation of New York State health regulations; total coliform was detected in 12 samples, and Escherichia coli was detected in 2 samples. The plate counts for heterotrophic bacteria exceeded the MCL (500 colony-forming units per milliliter) in four samples.

Open-File Report↗

USGS2007

Geophysical Logs of Selected Test Wells at the Diaz Chemical Superfund Site in Holley, New York

In June and July 2006, geophysical logs were collected and analyzed along with rock-core samples to define the bedrock stratigraphy and flow zones penetrated by four test wells at the Diaz Chemical Superfund site at Holley in eastern Orleans County, New York. The work was completed as a preliminary part of the investigation of contamination by organic compounds in the shale, mudstone, and sandstone bedrock. The geophysical logs included natural-gamma, caliper, borehole image, fluid properties, and flowmeter data. The orientation of fractures in the boreholes was inferred from the log data and summarized in stereo and tadpole plots; the transmissivity and hydraulic head was also determined for fracture zones that were observed to be hydraulically active through the flowmeter logs. The data are intended in part for use in the remediation of the site.

Open-File Report↗

USGS2007

Ground-Water Quality in the Genesee River Basin, New York, 2005-2006

Water samples were collected from 7 community water system wells and 15 private domestic wells throughout the Genesee River Basin in New York State (downstream from the Pennsylvania border) from October 2005 through March 2006 and analyzed to characterize the chemical quality of ground water in the basin. The wells were selected to represent areas of greatest ground-water use and to provide a representative sampling from the 2,439 square-mile basin area in New York. Samples were analyzed for five physical properties and 226 constituents that included nutrients, major inorganic ions, trace elements, radionuclides, pesticides, volatile organic compounds, and bacteria. The results show that ground water used for drinking water is generally of good quality in the Genesee River Basin, although concentrations of seven constituents exceeded drinking water standards. The cations that were detected in the highest concentrations were calcium, magnesium, and sodium; the anions that were detected in the greatest concentrations were bicarbonate, chloride, and sulfate. The predominant nutrient was nitrate, and nitrate concentrations were greater in samples from sand and gravel aquifers than in samples from bedrock aquifers. The trace elements barium, boron, cobalt, copper, and nickel were detected in every sample; the highest concentrations were barium, boron, chromium, iron, manganese, strontium, and lithium. Fourteen pesticides including seven pesticide degradates were detected in water from 12 of the 22 wells, but none of the concentrations exceeded Maximum Contaminant Levels (MCLs). Eight volatile organic compounds (VOCs) were detected in six samples, but none of the concentrations exceeded MCLs. Seven chemical analytes and three types of bacteria were present in concentrations that exceeded Federal and New York State water-quality standards, which are typically identical. Sulfate concentrations exceeded the U.S. Environmental Protection Agency (USEPA) Secondary Maximum Contaminant Level (SMCL) of 250 milligrams per liter (mg/L) in three samples; the chloride SMCL (250 mg/L) was exceeded in one sample. Sodium concentrations exceeded the USEPA Drinking Water Health Advisory of 60 mg/L in five samples. The SMCL for iron (300 ug/L) was exceeded in 11 filtered samples; the USEPA SMCL for manganese (50 ug/L) was exceeded in 10 filtered samples, and the New York State MCL (300 ug/L) was exceeded in 1 filtered sample. The MCL for aluminum (200 ug/L) was exceeded in 1 sample, and the MCL for arsenic (10 ug/L) was exceeded in 1 sample. Radon-222 exceeded the proposed USEPA MCL of 300 picocuries per liter in 16 samples. Any detection of total coliform or fecal coliform bacteria is considered a violation of New York State health regulations; in this study, total coliform was detected in eight samples; fecal coliform was detected in two samples, and Escherichia coli was detected in one sample.

Open-File Report↗

USGS2006

Ground-Water Quality in the Upper Susquehanna River Basin, New York, 2004-05

Water samples were collected from 20 production wells and 13 private residential wells throughout the upper Susquehanna River Basin (upstream from the Pennsylvania border) during the fall of 2004 and the spring of 2005 and analyzed to describe the chemical quality of ground water in the upper basin. Wells were selected to represent areas of greatest ground-water use and highest vulnerability to contamination, and to provide a representative sampling from the entire (4,516 square-mile) upper basin. Samples were analyzed for physical properties, nutrients, inorganic constituents, metals, radionuclides, pesticides, volatile organic compounds, and bacteria. The cations that were detected in the highest concentrations were calcium, magnesium, and sodium; the anions that were detected in the greatest concentrations were bicarbonate, chloride, and sulfate. The predominant nutrient was nitrate, the concentrations of which were greater in samples from sand and gravel aquifers than in samples from bedrock. The metals barium, boron, cobalt, copper, and nickel were detected in every sample; the metals with the highest concentrations were barium, boron, iron, manganese, strontium, and lithium. The pesticide compounds detected most frequently were atrazine, deethylatrazine, alachlor ESA, and two degradation products of metolachlor (metolachlor ESA and metolachlor OA); the compounds detected in highest concentration were metolachlor ESA and OA. Volatile organic compounds were detected in 11 samples, and concentrations of 3 of these compounds exceeded 1 microgram per liter (?g/L). Methyl tert-butyl ether (MTBE), a gasollline additive, was not detected in any sample. Several analytes were found in concentrations that exceeded Federal and New York State water-quality standards, which are typically identical. Chloride concentrations exceeded the U.S. Environmental Protection Agency (USEPA) Secondary Maximum Contaminant Level (SMCL) of 250 milligrams per liter (mg/L) in two samples, and sulfate concentrations exceeded the SMCL of 250 mg/L in one sample. Sodium concentrations exceeded the USEPA Drinking Water Advisory of 60 mg/L in six samples. Nitrate concentrations exceeded the USEPA Maximum Contaminant Level (MCL) of 10 mg/L in one sample and approached this limit (at 9.84 mg/L) in another sample. Barium concentrations exceeded the MCL of 2,000 ?g/L in one sample. Iron concentrations exceeded the SMCL of 300 ?g/L in five samples, and manganese concentrations exceeded the SMCL of 50 ?g/L in 14 samples. Arsenic was detected in seven samples, and the MCL for arsenic (10 ?g/L) was exceeded in two samples. Radon-222 exceeded the proposed MCL of 300 picocuries per liter in 24 samples. Any detection of total coliform or fecal coliform bacteria is considered a violation of New York State health regulations; in this study, total coliform was detected in six samples and fecal coliform was detected in one sample, but Escherichia coli (E. coli) was not detected in any sample.

Open-File Report↗

USGS2003

Geophysical, stratigraphic, and flow-zone logs of selected test, monitor, and water-supply wells in Cayuga County, New York

Volatile-organic compounds have been detected in water sampled from more than 50 supply wells between the City of Auburn and Village of Union Springs in Cayuga County, New York, and the area was declared a Superfund site in 2002. In 2001-04, geophysical logs were collected from 37 test, monitor, and water-supply wells as a preliminary part of the investigation of volatile-organic compound contamination in the carbonate-bedrock aquifer system. The geophysical logs included gamma, induction, caliper, wellbore image, deviation, fluid resistivity and temperature, and flowmeter. The geophysical logs were analyzed along with core samples and outcrops of the bedrock to define the stratigraphic units and flow zones penetrated by the wells. This report describes the logging methods used in the study and presents the geophysical, stratigraphic, and flow-zone logs.

Open-File Report↗