EXPLORE THE ARCHIVE

Andrew James Makdisi

Publications and source records attributed to Andrew James Makdisi.

6 recordsLinked to original sources

USGS2026

Development of liquefaction-targeted design basis in U.S. seismic provisions

Seismic design criteria for new buildings in the United States have historically focused on life safety performance objectives through minimizing the potential for structural collapse. Development of design criteria to meet this performance objective has evolved over time, leading to the current, risk-targeted maximum considered earthquake (MCE R ) design basis. Corresponding MCE R seismic design loads incorporate the full range of probabilistic ground motion hazard information available from U.S. Geological Survey National Seismic Hazard Models, as well as a representation of the uncertainty in structural collapse capacity. Despite these considerable advances in structural design criteria, guidelines for geotechnical hazards such as liquefaction-induced damage, which continue to be based on uniform ground-shaking hazard (i.e., MCE ground motions), are not well-connected with risk-based, collapse prevention performance objectives. This study, undertaken as part of Building Seismic Safety Council efforts to update recommended seismic provisions through the National Earthquake Hazards Reduction Program, presents probabilistic, liquefaction-targeted design objectives and corresponding ground motion parameters, with a focus on improving consistency in first-level screening criteria for liquefaction hazard assessment. This study identifies a potential maximum acceptable annualized probability of liquefaction triggering ( P L,max ) of 2.5% in 50 years, above which liquefaction consequences and potential mitigation measures would be considered. The P L,max -based design basis is calibrated to effective probabilistic liquefaction hazard levels obtained in practice using current MCE peak ground accelerations, and could be implemented via a new liquefaction-targeted maximum considered earthquake (MCE L ) peak ground acceleration ( PGA L ). The proposed PGA L is derived from probabilistic liquefaction hazard curves and includes uncertainties inherent to liquefaction hazard modeling. The potential design effects of the proposed PGA L are demonstrated via comparison with current MCE PGA levels, effects on first-level liquefaction screening analyses, and improvements in the consistency of P L,max levels across the United States, and for a wide range of site conditions.

conterminous United States↗

USGS2025

Preface to the focus section on earthquake-induced ground deformation

Ground failure due to earthquake-induced liquefaction, surface fault rupture, and landsliding has caused substantial damage in the past and continues to pose risks to critical infrastructure in the future. The consideration of ground failure is central to engineering analysis and design, ranging from site-specific engineering assessments of ground failure potential to broader regional-scale ground failure assessments of near-real-time earthquake impacts or longer-term portfolio risk. Uncertainties in all aspects of the problem complicate the prediction of earthquake-induced ground failure, including the identification of hazard-susceptible geomaterials, characterizing their spatial extent and physical properties, spatio-temporal variability in groundwater conditions, characterization of earthquake ground motions, assessing ground failure severity, and linking ground failure severity to infrastructure damage and loss.

Seismological Research Letters↗

USGS2025

Engineering and risk research—A strategic vision for extending USGS earthquake science to risk assessment and mitigation

As a part of the U.S. Geological Survey (USGS) Natural Hazards Mission Area, the Engineering and Risk Project (ERP) of the Geologic Hazards Science Center conducts civil engineering research to extend natural hazards science to risk assessments. The ERP includes predominantly, but not exclusively, staff funded by the USGS Earthquake Hazards Program. A major focus of the ERP is to deliver actionable information to decisionmakers that helps promote the safety, security, and economic well-being of the Nation. The report discusses briefly the ERP’s evolution and scope, its organization structure, describes key products and deliverables, their efforts to engage with external partners, and its strategy and vision in conducting range of engineering and risk research. The research topics outlined in this report, as developed by the ERP, may be used to facilitate project planning activities during the next 10 years and serve as a longer-term planning resource for the USGS Earthquake Hazards Program and Geologic Hazards Science Center.

Circular↗

USGS2025

Implications of physics-based M9 ground motions on liquefaction-induced damage in the Cascadia Subduction Zone: Looking forward and backward

Given the likelihood of future M9 Cascadia Subduction Zone (CSZ) earthquakes, various estimates of the resulting, regional ground motions have been made, including a suite of 30 physics-based simulations that reflect key modeling uncertainties. However, because the last CSZ interface rupture occurred in 1700 CE, the shaking expected in such an event is especially uncertain, as are the impacts to the built and living environments. Like other coseismic impacts, soil liquefaction poses a significant threat and must be considered by any scenario study used to inform planning and response, or to focus mitigation resources. Liquefaction is also notable for its potential to “ground truth” ground-motion estimates, given that its presence or absence in the geologic record can provide constraint on the intensities of shaking in past events. It is thus an important phenomenon looking both forward and backward. Accordingly, using recent physics-based simulations, this study (1) predicts liquefaction in M9 CSZ ruptures at 400 locations in Oregon, Washington, and British Columbia (BC) using an array of cone-penetration-test based models and (2) uses paleoliquefaction evidence at ten sites spanning from Southern Oregon to Vancouver, BC to constrain possible ground-motion intensities experienced in the 1700 CE earthquake. The forward predictions indicate that liquefaction in M9 events could be pervasive in the region and affect numerous population hubs, with the potential for damage across hundreds of square kilometers. The backward analyses suggest that 1700 CE ground-motion intensities may have been less than expected from M9 simulations in some northern portions of the CSZ (e.g. Seattle), given the paucity of 1700 CE liquefaction evidence in these areas. Ultimately, further discovery and analysis of CSZ paleoliquefaction, or lack thereof, will confirm or modify this possibility and the conclusions drawn herein.

Oregon, Washington↗

USGS2024

Effective site coefficients for the 2024 International Building Code (IBC)

The U.S. National Seismic Hazard Models (NSHMs), developed by the U.S. Geological Survey (USGS), have long been the scientific foundation of seismic design guidelines and have been used to compute design ground motions for construction of new buildings and retrofit of existing buildings in the United States and its territories. The 2018 NSHM is adopted by the 2024 International Building Code (IBC). Prior to the 2018 NSHM update, hazard calculations were required only at one reference site condition defined by V S30 =760 m/s (where V S30 is the time-averaged shear wave velocity from the surface to a depth of 30 m) and three periods (peak ground acceleration, PGA, and pseudo spectral accelerations at periods of 0.2 and 1 s, S s and S 1 ). Site coefficients, F PGA , F a , and F v , were then defined by the Building Seismic Safety Council (BSSC) Provisions Update Committee (PUC) in the site-specific procedures of National Earthquake Hazard Reduction Program (NEHRP) Recommended Seismic Provisions to calculate ground motions for other site classes with different V S30 values at the given periods. The design ground motions at other periods were then estimated using a generic spectral shape that was also defined by the BSSC PUC in NEHRP provisions. In recent years, the engineering community has realized there were deficiencies with the F a and F v site coefficients and the generic spectral shape. To avoid potentially dangerous underestimations of design ground motions for long period structures on soft site conditions in high seismicity regions, the BSSC PUC recommended the use of multi-period response spectra (MPRS) in 2017. As a result, the USGS produced multi-period and multi-V S30 response spectral values in the 2018 NSHM for calculations of design ground motions and the site coefficients F a and F v were eliminated from the 2020 NEHRP Provisions. As these site coefficients were widely used inside and outside of the United States, in this study we back-calculate the “effective” site coefficients F a,eff , and F v,eff by comparing MPRS for various site classes with the MPRS for the reference site condition, and discuss the changes that are observed in the 2024 IBC compared to its previous version in 2021. The effective site coefficients are presented for test site locations and their dependence on various factors including period, ground motion intensity, and regional models are discussed. Ratio maps between the new effective site coefficients and the old ones are then presented for soft site classes and for short and long periods. For soft site classes at short periods, the new effective site coefficients are lower than the old site coefficients for high seismicity regions and higher for low seismicity regions. As it was expected, for soft site classes at long periods and high seismicity regions, the new effective site coefficients are much larger than the old site coefficients without imposing the 50% increase as a penalty that was suggested in the 2021 IBC, whereas they could be much smaller if the 50% increase would have been imposed particularly around New Madrid and Charleston high seismicity regions. For low seismicity regions, the long period effective site coefficients can be smaller or larger by 20% compared to the 2021 IBC coefficients.

Conference Paper↗

USGS2024

Framework for mapping liquefaction hazard–Targeted design ground motions

Liquefaction-induced ground failure poses substantial challenges to geotechnical earthquake engineering design. Current approaches for designing against liquefaction hazards, as specified in most seismic provisions, focus on estimating a liquefaction factor of safety ( 𝐹⁢𝑆𝐿 ) and typically characterize earthquake loading using design parameters based on probabilistic or deterministic ground motion levels. Because 𝐹⁢𝑆𝐿 is estimated deterministically, this basis of design neglects considerable uncertainties for estimating liquefaction triggering and its consequences and results in a lack of liquefaction-specific design criteria, particularly as structural design has advanced toward risk-targeted performance objectives. This study presents a framework for developing liquefaction-targeted design criteria based on a minimum acceptable return period of liquefaction, informed by probabilistic liquefaction hazard analysis (PLHA). PLHA quantifies annualized rates of liquefaction by considering contributions from (1) the full ground-motion probability space, and (2) uncertainties in liquefaction triggering using probabilistic models. PLHA is used in this study to characterize the current, effective return periods of 𝐹⁢𝑆𝐿 ( 𝑇𝑅,𝐹⁢𝑆 ) obtained from conventional liquefaction hazard analysis (CLHA) using uniform-hazard ground motions. 𝑇𝑅,𝐹⁢𝑆 is evaluated in a parametric study of nearly 100 sites throughout the conterminous United States. The results indicate large geographic variations in acceptable liquefaction hazard levels, with implied 𝑇𝑅,𝐹⁢𝑆 ranging between approximately 1,000 to 3,000 years. To address these inconsistencies without the computational demands of full PLHA, a framework is proposed for developing a liquefaction-targeted design peak ground acceleration, 𝑃⁢𝐺⁢𝐴𝐿 , for use in liquefaction models that result in consistent liquefaction design levels across all geographic locations. The mapped 𝑃⁢𝐺⁢𝐴𝐿 is shown to be somewhat sensitive to site-specific properties, and adjustment factors are developed and presented. The proposed 𝑃⁢𝐺⁢𝐴𝐿 mapping procedure produces 𝐹⁢𝑆𝐿 estimates that are consistent with those obtained from full PLHA at a target 𝑇𝑅,𝐹⁢𝑆 , providing a promising roadmap to incorporating PLHA concepts into current liquefaction design methods.

Journal of Geotechnical and Geoenvironmental Engin↗