Geology Reports⌕ Search

FIND YOUR NEXT DISCOVERY

Results for “Journal of Waterway, Port, Coastal, and Ocean Engineering”

Original records, connected by a shared subject.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,281 recordsLinked to original sources
USGS2026

A process-based model for forecasting wave runup along the coast of Georgia

Wave runup is an important nearshore process that impacts total water level, sediment transport, and coastal design. Current methods for forecasting wave runup implement an empirical model that considers offshore wave height, wave period, and generalized beach slope. In this study, the authors generated wave runup forecasts from offshore wave conditions and a system of polynomial equations derived from numerical simulations at three different still water datums for each beach profile. They developed a process-based methodology that incorporated site-specific cross-shore topobathy into the phase-resolving numerical model. A comparison between the system of equations, deterministic hydrodynamic simulations, and observed high-water marks was made using Hurricanes Matthew (2016) and Irma (2017) for 12 cases, and it showed that the polynomials were capable of being consistent with the results from full simulation runs, while not requiring hours of runtime when a forecast was needed—the differences between the polynomial and the observed high water marks ranged from 3 to 32 cm for the Irma hindcast and 9–70 cm for Matthew. Then, using forcings from Hurricanes Ian and Nicole (2022), the model predicted the occurrence of dune collision, overwash, and inundation for the coast of Georgia and suggested that wave runup was impacted by the still water level and local topobathy.

Georgia↗
USGS2024

Groundwater and surface-water interactions in the Lower Duwamish Waterway, Seattle, Washington

The U.S. Geological Survey (USGS), in cooperation with the Washington State Department of Ecology (Ecology), conducted a study to describe the current understanding of the regional groundwater system of the lower Duwamish River valley and groundwater and surface-water interactions in the lower Duwamish Waterway. The lower Duwamish Waterway is the final 5-mile (mi) reach of the Duwamish River before it empties into Elliott Bay in Puget Sound near Seattle, Washington. A nearshore site (hereinafter referred to as “Nearshore Site” to distinguish the particular site from general discussions of nearshore areas) along the western shoreline of the Duwamish River, about 1.5 mi upstream from the river mouth, was selected for focused groundwater data collection by USGS. Data loggers were deployed in seven groundwater wells and one stilling well in the Duwamish River to measure specific conductance, temperature, and depth at 15-minute intervals for a period of about 2 years. At the Nearshore Site during 2020–22, water levels in the shallow wells were 3–8 feet (ft) higher than water levels in the deep wells, providing evidence for a low-permeability layer between the shallow and deep aquifers in this area. The shallow wells had a pronounced seasonal variability, with high water levels in winter and low water levels in summer. Data from the deep wells showed far less seasonal variability, with slight increases in winter and a near-constant water level from spring to autumn. The deep wells had a strong hydraulic connection to the Duwamish River, as evidenced by the synchronous water-level variability during the tidal cycle, whereas the shallow wells had minimal to no tidal response. The potentiometric maps developed for the Nearshore Site and surrounding areas indicate large differences in groundwater-flow directions for the shallow and deep aquifers at low and high tides. For the shallow aquifer, flow is toward the lower Duwamish Waterway near the Nearshore Site, regardless of the tidal condition. For the deep aquifer, a potentiometric trough forms parallel to the shoreline during high tide, indicating that groundwater flow converges from the uplands to the west and the Duwamish River to the east. The geometry of the potentiometric surfaces between the nearshore-most well and the shoreline is complex and is further confounded by intermittent shoreline armoring and other buried infrastructure, which could serve as either a barrier or a conduit to flow. Groundwater and surface-water interactions in the lower Duwamish Waterway are inherently complex as a result of three overarching factors. First, water levels in the lower reaches of the Duwamish River vary daily by 11–16 ft because of tides from Puget Sound, which create large swings in the hydraulic gradient in the nearshore groundwater system. Second, the density and chemical composition of water in the Duwamish River change daily with the tides and seasonally, which constrains how river water entering the nearshore sediments interacts with discharging groundwater. Third, the nearshore subsurface and shoreline conditions are heterogenous because of extensive shoreline armoring over the past century, which governs the flow of groundwater and infiltrating river water. These unique features of groundwater and surface-water interactions in the lower Duwamish Waterway thus govern the transport of terrestrial contaminants to the lower Duwamish Waterway. Furthermore, the heterogenous aquifer properties in the lower Duwamish Waterway contribute to spatially and temporally dynamic contaminant-transport processes.

Washington↗
USGS2025

Shallow geologic framework of the Mississippi Sound and the potential for sediment resources

The Mississippi Sound, an estuarine environment located between the mainland and barrier islands bordering the northern Gulf of America (formerly the Gulf of Mexico), serves as a vital ecosystem for the States of Mississippi and Alabama. Spanning approximately 100 kilometers from east to west and covering 1,400 square kilometers, the sound is home to marine industry and ports, and its shallow and brackish waters sustain a diverse array of marine life. Barrier islands along the southern edge of the sound separate the microtidal estuary from the Gulf of America. This protection from gulf wave action mediates current flow within the sound, resulting in predominantly fine-grained sediment deposition along the seafloor. This study, conducted by the U.S. Geological Survey in cooperation with the U.S. Army Corps of Engineers, provides insight on fluvial and tidal processes spanning the past 5,000 years. The report synthesizes existing research to provide a comprehensive overview of the sound geology, from Pleistocene origins to present-day morphology, and utilizes high-resolution single channel seismic profiles and sediment data to identify and map sedimentary deposits and morphologic features at and below the seafloor. Despite its ecological significance, the Mississippi Sound faces environmental challenges, including water-quality issues, habitat degradation, storm-induced erosion, and the ongoing threats of sea-level rise and environmental changes. This study uses the present-day understanding of the sound's geology to inform coastal management decisions, hazard assessment, and potential mineral resources.

Louisiana, Mississippi↗
USGS2025

The 3D Elevation Program—Supporting the economy of Massachusetts

Introduction Massachusetts extends from the mountains of the Appalachian system in the west of the State to the sandy beaches and rocky shorelines of the Atlantic coast in the east. Inland topographic data support a wide range of important activities, including geologic mapping, transportation planning, forest and wildlife management, quantifying ecological services, water supply protection, commonwealth-wide infrastructure planning, local site planning, and flood-plain management. Nearshore bathymetry can be used to support coastal portions of the Commonwealth by addressing the combined threats of ocean warming, strong storm surge, and rising sea levels. The maintenance and (or) expansion of Massachusetts ports (for instance, Boston, New Bedford) and Cape Cod sediment management depends upon the accurate mapping of bathymetry and the frequent influx of sediment and redeposition. Critical applications that address the broad range of requirements depend on light detection and ranging (lidar) data that provide a highly detailed three-dimensional (3D) model of the Earth’s surface and aboveground features. The 3D Elevation Program (3DEP) is managed by the U.S. Geological Survey (USGS) in partnership with Federal, State, Tribal, U.S. territorial, and local agencies to acquire consistent lidar coverage at quality level 2 or better to meet the many needs of the Nation and Massachusetts. The status of available and in-progress 3DEP baseline lidar data in Massachusetts is shown in figure 1. 3DEP baseline lidar data include quality level 2 or better, 1-meter or better digital elevation models, and lidar point clouds, and must meet the Lidar Base Specification version 1.2 ( https://www.usgs.gov/3dep/lidarspec ) or newer requirements. The National Enhanced Elevation Assessment identified user requirements and conservatively estimated that availability of lidar data would result in at least $1.23 million in new benefits annually to Massachusetts. The top 10 Massachusetts business uses for 3D elevation data, which are based on the estimated annual conservative benefits of 3DEP, are shown in table 2.

Massachusetts↗
USGS2025

Estimated average annualized tsunami losses for the United States

Tsunami hazards are substantial threats to coastal communities across the United States (U.S.) and its territories. U.S. states and territories collaborate through the National Tsunami Hazard Mitigation Program (NTHMP) to develop their own tsunami-hazard information for outreach and evacuation planning. An effort to curate this tsunami-hazard information to support comprehensive risk analysis at the national level has not yet been completed. In support of this effort, the Federal Emergency Management Agency (FEMA) collaborated with the NTHMP, the National Oceanic and Atmospheric Administration (NOAA) and the U.S. Geological Survey (USGS) starting in 2023. This collaboration included the collection and analysis of existing tsunami hazard data and methods in the U.S. Tsunami subject matter experts identified and selected scientifically defensible methods for estimating the risks to buildings and populations in coastal communities. These efforts may support decision making regarding resilience policies, priorities, strategies and funding levels. Tsunamis can be triggered by earthquakes, subaerial or submarine landslides, volcanic eruptions, glacial calving, near-earth objects, weather or other events. These events can cause severe destruction, injuries, and loss of life due to powerful currents and flooding. Tsunamis pose a substantial threat to the western United States and all U.S. territories, as described below. ■ Hawaii is threatened by distant tsunamis due to its central location in the Pacific Ocean basin and has a history of local events. ■ Alaska, particularly the Aleutian Islands, faces local tsunami threats due to proximity to the Alaska-Aleutian Subduction Zone, as well as distant tsunamis from around the Pacific Ocean basin. ■ The western coast of the U.S. is threatened by distant tsunamis from around the Pacific Ocean basin and local source tsunamis from earthquakes generated within the Cascadia Subduction Zone in the Pacific Northwest. ■ American Samoa faces local tsunami threats from earthquakes generated in the nearby Tonga Trench, as well as distant tsunami threats. ■ Guam and the Commonwealth of the Northern Mariana Islands are threatened by local tsunamis from the nearby Mariana Subduction Zone, as well as distant sources from around the Pacific Ocean Basin. ■ Puerto Rico and the United States Virgin Islands are threatened by multiple local and distant tsunami sources, such as the Puerto Rico Trench (PRT), given their location in the complex seismic region of the Caribbean Sea. Several historical events stand out because of their catastrophic impacts. ■ In the Pacific Northwest, the 1700 Cascadia earthquake caused a tsunami that affected coastal Native American communities, though the extent of the damage is not fully documented (Ludwin, et al., 2005). ■ In Puerto Rico, the 1918 earthquake triggered a tsunami that caused $77 million in damage in 2022 dollars and 116 fatalities, primarily along the western coast (Coffman et al., 1982). ■ The 1946 Aleutian Islands earthquake triggered a massive tsunami that devastated Hilo, Hawaii, killing 158 people and resulting in approximately $375 million in damage (adjusted to 2022 dollars) (Fisher et al., 2023). ■ The 1964 Alaska earthquake (M 9.2) generated tsunamis that caused severe destruction in some communities across Alaska, Oregon, and California. This disaster led to a total of 124 fatalities and approximately $2.9 billion in property damage (adjusted to 2022 dollars) (Brocher et al., 2014) (Alaska Science Center, 2024). ■ In American Samoa, a tsunami generated by the 2009 Samoa earthquake (Mw 8.1) caused widespread devastation, resulting in 34 confirmed fatalities (Apatu et al., 2013) and economic losses exceeding $160 million (adjusted to 2022 dollars) (DHS, 2011). More recent events, including the 2010 Chile earthquake, the 2011 Japan earthquake, and the 2022 Tonga volcanic eruption, resulted in millions of dollars in damage to numerous ports and harbors in the U.S. South Pacific territories, Hawaii, and along the west coast of the U.S. (Lynett, et al., 2022) (Wilson, et al., 2013). Since these events, the expansion of the built environment in lowlying areas along the coast has increased the exposure of buildings and people, thereby further escalating community risk from tsunamis. This report provides a comprehensive national assessment of earthquake-generated tsunami risk. It does not include impacts from tsunamis generated by landslides, volcanic eruptions, glacial calving, near-earth objects, weather, or other events. This study is based on the best available hazard data from the U.S. Pacific Coast (California, Oregon and Washington), Alaska, Hawaii, U.S. Pacific Territories (American Samoa, Guam and Commonwealth of the Northern Mariana Islands) and Caribbean Territories (Puerto Rico and United States Virgin Islands). Tsunami risks associated with states along the East Coast, Gulf Coast, and Great Lakes are not included in this study because Hazus 6.1 software (FEMA 2024a) does not currently include the ability to analyze tsunami risk in those states. Once modeling capabilities and tsunami hazard data become available for additional states, FEMA may incorporate these data into future editions of this study.

Alaska, California, Hawaii Oregon, Washington↗
USGS2026

Preliminary bedrock geologic map of the Port Henry quadrangle, Essex County, New York, and Addison County, Vermont

Introduction The bedrock geology of the 7.5-minute Port Henry quadrangle consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 Ga (giga-annum). In the Port Henry quadrangle, the AMCG metaigneous rocks (Yhg, Ygb, Yanw) intruded older, mostly metasedimentary rocks of the Grenville Complex during the middle to late Shawinigan orogeny (~1,160–1,150 Ma [mega-annum]). All rocks were subsequently metamorphosed to upper amphibolite to granulite facies conditions during the 1,080–1,050 Ma Ottawan orogeny. New mapping reveals four periods of deformation: (1) D1 produced rarely preserved isoclinal folds in the paragneiss and marble and predates AMCG magmatism. (2) Subsequent D2 deformation produced the dominant gneissic fabric preserved in the rock, recumbent folding, and deformed all the Proterozoic units in the map area. Syn- to late-D2 felsic magmatism resulted in the regionally extensive Lyon Mountain Granite Gneiss, which hosts numerous magnetite ore bodies. (3) Mylonitic extensional shear zones and core complex formation marked the beginning of D3 deformation. Protracted D3 deformation resulted in F3 upright folding, dome and basin formation, pegmatite intrusion, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron-ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. (4) D4 created northeast- and northwest-trending local high-grade ductile shear zones and boudinage, northwest-trending regional kilometer (km)-wide ductile shear zones, and crosscutting granitic pegmatite dikes. The development of the late-stage regional shear zones (D4) was likely due to the continuation of extensional doming and uplift from upper amphibolite facies conditions at the end of the Ottawan orogeny. The majority of iron-ore deposits in the Port Henry and adjacent Witherbee quadrangles are in the hanging wall of these extensional shear zones. In the Port Henry quadrangle, the km-wide Cheney Mountain shear zone is the result of D4 deformation. Kilometer-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. The Paleozoic rocks are part of the Early Cambrian to Late Ordovician carbonate bank on the ancient margin of Laurentia. The approximately 1-km-thick Cambrian to Ordovician stratigraphy records a transition from synrift clastics to passive-margin peritidal carbonate buildups to gradually deeper-water subtidal- to shelf-carbonates during foreland basin development associated with the Taconic orogeny. The Paleozoic rocks are weakly folded and block faulted. Large areas of the Champlain Valley are covered by undifferentiated glacial deposits, some of which contain mapped landslides. The map also shows waste rock piles and tailings from historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondacks, provide a context for historical iron mines in the eastern Adirondacks, and update the stratigraphy of the Champlain Valley in New York and Vermont. This Open-File Report includes a bedrock geologic map; a description of map units; a correlation of map units; and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information.

New York, Vermont↗
USGS2026

HyFlood: A surrogate-model-based framework for compound coastal flooding

Compound coastal flooding is a major threat to low-lying coastal regions and is expected to intensify under future climate change projections. However, modeling the joint interaction of waves, storm surge, tides, and rainfall remains computationally demanding, limiting the development of fast and reliable forecast tools. Here we present HyFlood, a hybrid statistical-numerical downscaling framework capable of computing and mapping high-resolution compound flood hazards while substantially reducing the computational cost compared with fully process-based hydrodynamic modeling. HyFlood combines statistical sampling and selection algorithms with a cascade of reduced-complexity surrogate models that emulate nearshore wave transformation, surf-zone hydrodynamics, and coastal, fluvial, and pluvial flooding. The surrogate models employ machine-learning and regression algorithms applied to a low-dimensional representation of the flooding outputs, obtained through statistical dimensionality reduction. The framework is demonstrated in southern O'ahu, Hawai'i, a region exposed to elevated sea levels driven by tides, waves, and storm surge along with frequent precipitation-driven flash flooding. Validation of the surrogates against the physics-based model outputs demonstrates that HyFlood accurately reproduces daily maxima of spatially distributed flooding depths. This hybrid approach offers a scalable and efficient tool to better quantify how changes in flooding drivers translate into hazard and impact assessments, and to support compound-flood risk assessments and climate-change adaptation planning.

Hawaii↗
USGS2025

Potentiometric surface maps and groundwater-level hydrographs for confined aquifers of the New Jersey Coastal Plain, 2018

The U.S. Geological Survey, in cooperation with the New Jersey Department of Environmental Protection (NJDEP), prepared potentiometric surface maps for 10 confined aquifers of the New Jersey Coastal Plain physiographic province based on water-level measurements collected during late 2018 and early 2019 from 951 wells in New Jersey and parts of Pennsylvania and Delaware. Maps were prepared for the confined Cohansey aquifer, Rio Grande water-bearing zone, Atlantic City 800-foot sand, Piney Point aquifer, Vincentown aquifer, Wenonah-Mount Laurel aquifer, Englishtown aquifer system, and the upper, middle, and lower aquifers of the Potomac-Raritan-Magothy aquifer system. Potentiometric surface maps indicate regional cones of depression in the following aquifers and the counties in which they are centered: Atlantic City 800-foot sand in Atlantic County, the Piney Point aquifer in Cumberland County, the Wenonah-Mount Laurel aquifer and Englishtown aquifer system in Monmouth and Ocean Counties, the Wenonah-Mount Laurel aquifer in Camden and Gloucester County, the upper aquifer of the Potomac-Raritan-Magothy aquifer system in Ocean County, and the upper, middle, and lower aquifers of the Potomac-Raritan-Magothy aquifer system in Camden County. Cones of depression with smaller areal extents were in the confined Cohansey aquifer, the Rio Grande water-bearing zone, the Atlantic City 800-foot sand centered in Cape May County, the Piney Point aquifer centered in Ocean County, the Wenonah-Mount Laurel aquifer in Salem and Burlington Counties, the Englishtown aquifer system in Camden County, the upper aquifer of the Potomac-Raritan-Magothy aquifer system in Monmouth County, and the middle aquifer of the Potomac-Raritan-Magothy aquifer system in Monmouth, Ocean, and Salem Counties. No cone of depression was interpreted in the Vincentown aquifer. Long-term hydrographs are presented for 75 wells spanning each of the 10 confined aquifers, and contain a mix of discrete water-level measurements and daily mean water levels based on continuously recorded 15-minute data. Changes of water levels during 2014–19, as indicated by the hydrographs, were compared with those of previous periods to assess any departures from historical data. During 2014–19, water levels were stable and fluctuated within similar ranges as previous periods in the following aquifers and locations: all wells in the confined Cohansey aquifer, the Rio Grande water-bearing zone, the Vincentown aquifer, the Englishtown aquifer system, the Piney Point aquifer wells in Burlington and Ocean Counties, six of eight wells in the Wenonah-Mount Laurel aquifer, all wells in the upper and lower aquifers of the Potomac-Raritan-Magothy aquifer system outside NJDEP Critical Areas, and all wells in the middle aquifer of the Potomac-Raritan-Magothy aquifer system except those within NJDEP Critical Area II. Increasing water levels in 2014–19, ongoing since historical periods, were indicated in the following aquifers and locations: Atlantic County wells in the Piney Point aquifer, all wells in the upper and lower aquifers of the Potomac-Raritan-Magothy aquifer system outside NJDEP Critical Areas, and all wells in the middle aquifer of the Potomac-Raritan-Magothy aquifer system within NJDEP Critical Area II. Water levels in the Atlantic City 800-foot sand also increased during 2014–19 in wells in Atlantic County and northern Cape May County closer to the center of the cone of depression in that aquifer, which is a response unique to this period and absent from previous periods. During 2013–19, continued decreasing water levels, ongoing since previous periods, were indicated by hydrographs of Atlantic City 800-foot sand wells in southern Cape May County, Piney Point aquifer wells in Cumberland County where the regional cone of depression is located, and two wells in the Wenonah-Mount Laurel aquifer—070478, which in 2014–19 departed from previous periods, and 330020, which continued a gradual decrease throughout its period of record.

New Jersey↗
USGS2024

Editorial: From cold seeps to hydrothermal vents: Geology, chemistry, microbiology, and ecology in marine and coastal environments

This Research Topic compiles contemporary studies on cold seeps, hydrothermal vents, mud volcanoes, and related seafloor features that are associated with focused fluid emissions and the transfer of carbon, other chemical species, and sometimes heat from the geosphere to the ocean. Because these features sometimes tap fluids and gas originating kilometers below the seafloor, they provide an important window into deep processes that are otherwise inaccessible to scientists. At the shallow portion of their journey, migrating fluids nearing the seafloor contribute to a range of unique biological, physical, and chemical processes within the sediments themselves and at the sediment-water interface. Seafloor fluid emissions play a critical role in global biogeochemical cycles, ocean chemistry, and possibly even climate change. Seafloor leakage points often emit hydrocarbon gases (especially methane and CO 2 ) and are sometimes the loci for deposition of seafloor minerals that have economic value. A burgeoning area of research focuses on natural products generated at these features, seeking compounds with potential pharmaceutical or other applications. Multidisciplinary studies have become routine for characterization of seafloor fluid emission sites, attesting to the inseparability of geologic, physical, chemical, and biological processes in these settings. It is increasingly common for researchers to combine in a single research cruise: subbottom imaging and seafloor mapping; porewater and water column geochemistry and gas sampling; sediment retrieval for lithologic, biostratigraphic, and solid phase analyses; and studies of benthic and subseafloor communities at the microbial to macrofaunal scales. This multidisciplinary approach has the advantage of ensuring the spatial and temporal coincidence of surveys and samples, an important factor at highly dynamic seafloor fluid emission sites. In addition, researchers often use remotely operated vehicles (ROVs), autonomous underwater vehicles (AUVs), or human-occupied vehicles (HOVs) to record video of the seafloor, compile photomosaics, collect targeted samples, and survey with high-resolution geophysical near-seafloor systems, providing a degree of detail about seafloor fluid emission sites that is unprecedented compared to most areas of the deep ocean. While rarer, long-term cabled observatories or shorter-term deployments of portable observatories are also used at some loci for seafloor fluid flux and are particularly helpful for capturing temporal variations at these dynamic features. Here we summarize the Research Topic’s contribution to multidisciplinary seafloor emission studies in the categories of cold seeps, mud volcanoes, and hydrothermal vents. Figure 1 shows the geographic distribution of the studies in this Research Topic and key features referred to in this Introduction.

Frontiers in Earth Science↗
USGS2026

Decadal-scale characteristics of natural and anthropogenic dune morphology along North Carolina Barrier Islands (SE Atlantic Coast)

Dunes offer protection to coastal communities from storms, yet quantitative research characterizing human influences on dune systems across decades and 10–100 km spatial scales constitutes a known data gap. This study analyzed a multidecadal archive of dune crest elevations and positions to map mesoscale spatiotemporal trends in foredune morphology across the barrier island coastline of North Carolina, SE Atlantic coast. Results are summarized within four categories of coastline representing a range of coastal management intensities, integrating beach width and dune lateral accommodation space to assess the comparative influence of differing intensities of anthropogenic intervention on dune morphology. These categories account for the presence of structures, roads, and alongshore connectivity to anthropogenic sediment sources (beach nourishment). These categories show distinct dune and beach system characteristics. Dunes are largest in the areas with the longest legacy of coastal management. As categories decrease in development intensity, dune and beach system characteristics generally depart from the large, static dunes and narrow beaches consistent with hold-the-line management. Where small or transgressive dunes exist on heavily developed coasts, they coincide with relatively strong hydrodynamic forcing or sediment-limiting geology. There is evidence of indirect coastal management influence on undeveloped barrier islands with alongshore connectivity to developed barriers. While this analysis was conducted at the mesoscale, the results provide researchers with the framework to make insights at smaller scales than those demonstrated in this study.

North Carolina↗
USGS2026

Simulated ground motion dataset in the Azores Plateau, Portugal, on rock and soil sites

Building on a previously developed bedrock dataset, this study extends the Azores Plateau ground motion simulations to include soil-amplified records and introduces a comprehensive validation framework. Soil amplification is modeled using one-dimensional soil profiles. A stochastic source-based approach is employed to generate the dataset, incorporating randomization of input-model parameters to account for the aleatory uncertainty in seismic activity. The accuracy of the dataset is verified through a comprehensive validation framework, showing that the randomization effectively captures variance and inter-period correlation observed in records. This work provides a robust dataset for advancing seismic hazard and risk assessment in the Azores Plateau.

central and eastern Azores islands↗
USGS2000

Storm impact scale for barrier islands

A new scale is proposed that categorizes impacts to natural barrier islands resulting from tropical and extra-tropical storms. The proposed scale is fundamentally different than existing storm-related scales in that the coupling between forcing processes and the geometry of the coast is explicitly included. Four regimes, representing different levels of impact, are defined. Within each regime, patterns and relative magnitudes of net erosion and accretion are argued to be unique. The borders between regimes represent thresholds defining where processes and magnitudes of impacts change dramatically. Impact level 1 is the 'swash' regime describing a storm where runup is confined to the foreshore. The foreshore typically erodes during the storm and recovers following the storm; hence, there is no net change. Impact level 2 is the 'collision' regime describing a storm where the wave runup exceeds the threshold of the base of the foredune ridge. Swash impacts the dune forcing net erosion. Impact level 3 is the 'overwash' regime describing a storm where wave runup overtops the berm or, if present, the foredune ridge. The associated net landward sand transport contributes to net migration of the barrier landward. Impact level 4 is the 'inundation' regime describing a storm where the storm surge is sufficient to completely and continuously submerge the barrier island. Sand undergoes net landward transport over the barrier island; limited evidence suggests the quantities and distance of transport are much greater than what occurs during the 'overwash' regime.

Journal of Coastal Research↗
USGS2024

Projections of multiple climate-related coastal hazards for the US Southeast Atlantic

Faced with accelerating sea level rise and changing ocean storm conditions, coastal communities require comprehensive assessments of climate-driven hazard impacts to inform adaptation measures. Previous studies have focused on flooding but rarely on other climate-related coastal hazards, such as subsidence, beach erosion and groundwater. Here, we project societal exposure to multiple hazards along the Southeast Atlantic coast of the United States. Assuming 1 m of sea level rise, more than 70% of the coastal residents and US \ $ 1 trillion in property are in areas projected to experience shallow and emerging groundwater, 15 times higher than daily flooding. Storms increase flooding exposure by an order of magnitude over daily flooding, which could impact up to ~50% of all coastal residents and US \ $ 770 billion in property value. The loss of up to ~80% of present-day beaches and high subsidence rates that currently affect over 1 million residents will exacerbate flooding and groundwater hazard risks.

Florida, Georgia, North Carolina, South Carolina, ↗
USGS2026

PFAS remediation in a bioelectrochemical system inoculated with the west branch consortium (WBC-2)

Groundwater contamination by per - and polyfluoroalkyl substances (PFAS) poses a persistent environmental and public health concern. This study evaluates a two-chambered bioelectrochemical system (BES) inoculated with the West Branch Consortium (WBC-2) for PFAS remediation. Under an applied cathodic potential of −450 mV (versus Ag/AgCl), the BES with active WBC-2 achieved >99.0% perfluorooctanesulfonic acid (PFOS) removal within 21 days in deionized water with culture medium and > 98.9% removal of PFOS, perfluorooctanoic acid (PFOA), perfluorohexanoic acid (PFHxA), and perfluorohexanesulfonic acid (PFHxS) in contaminated groundwater after 102 days. Intermediate formation (e.g., PFOA, 6:2 fluorotelomer sulfonate (6:2 FTS), perfluoropropionic acid (PFPrA), perfluorobutanoic acid (PFBA)) and background-corrected fluoride release were consistent with PFOS transformation under anaerobic reducing conditions potentially involving defluorination. Following repeated PFOS spikes (100 μg/L on Days 0, 50, and 399), PFOA, PFPrA, and PFBA accumulated over 664 days. Despite being the dominant accumulated compound, PFOA accounted for <1.8% of the total spiked PFOS mass. Minimal PFOS transformation occurred in controls without active WBC-2, highlighting the importance of microbial metabolism. Biofilm analysis revealed dense colonization of rod-shaped bacteria on carbon fiber brushes. Enrichment of Bacillus , Agrobacterium , and other low-abundance taxa suggests selective adaptation to BES and PFAS conditions. These findings highlight BES driven by electrochemically stimulated microbial activity as a promising strategy for PFAS remediation.

Journal of Water Process Engineering↗
USGS2026

Assessing environmental drivers of denitrification in restored riverine floodplains

Restoration of impaired floodplains is an increasingly prevalent strategy for alleviating water quality concerns and reducing downstream flooding at watershed scales. Floodplains temporarily store water and slow flow velocity to promote sedimentation during overbank flooding and remove inorganic nitrogen from floodwater and groundwater via denitrification. Evaluating the impacts of different restoration strategies on denitrification can inform more strategic investments into floodplain modifications that improve water quality outcomes. Our research investigates how denitrification rates in floodplains respond to environmental factors that are actionable from an engineering perspective through design and water resources management. We seasonally measured soil denitrification enzyme activity and various environmental characteristics in 4 floodplains with different restoration design and management approaches at the confluence of the Wabash and Tippecanoe Rivers in Indiana, United States. Our results showed that denitrification rates in an agricultural floodplain were significantly lower than in restored floodplains with native vegetation. Certain soil conditions characteristic of floodplain wetlands were associated with higher denitrification, particularly elevated total nitrogen, moisture, silt, and organic matter contents. Vegetation species composition was correlated with denitrification rates. This link may reflect the direct effects of vegetation on soil conditions, such as supplying labile organic carbon, or indirect effects, such as vegetation acting as an indicator of hydrologic regime and land use. Denitrification seasonally varied, peaking in winter when nitrate supply from rivers draining agricultural watersheds in the region is also high. Substrate limitation of soil denitrification enzyme activity was most significant during the summer when overbank flooding, which replenishes soil nitrogen stocks, rarely occurs. Our findings indicate that denitrification capacity will likely be maximized in riverine floodplains that are restored as wetlands with diverse native vegetation and enhanced hydrologic connectivity. Such restoration activities promote higher denitrification rates via elevated moisture, fine sediment deposition, and soil organic matter.

Tippecanoe River, Wabash River↗
USGS1999

Water-quality assessment of the New England coastal basins in Maine, Massachusetts, New Hampshire, and Rhode Island: Environmental settings and implications for water quality and aquatic biota

The New England Coastal Basins in Maine, Massachusetts, New Hampshire, and Rhode Island constitute one of 59 study units selected for water-quality assessment as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) program. England Coastal Basins study unit encompasses the fresh surface waters and ground waters in a 23,000 square-mile area that drains to the Atlantic Ocean. Major basins include those of the Kennebec, Androscoggin, Saco, Merrimack, Charles, Blackstone, Taunton, and Pawcatuck Rivers. Defining the environmental setting of the study unit is the first step in designing and conducting a multi-disciplinary regional water-quality assessment. The report describes the natural and human factors that affect water quality in the basins and includes descriptions of the physiography, climate, geology, soils, surface- and ground-water hydrology, land use, and the aquatic ecosystem. Although surface-water quality has greatly improved over the past 30 years as a result of improved wastewater treatment at municipal and industrial wastewater facilities, a number of water-quality problems remain. Industrial and municipal wastewater discharges, combined sewer overflows, hydrologic modifications from dams and water diversions, and runoff from urban land use are the major causes of water-quality degradation in 1998. The most frequently detected contaminants in ground water in the study area are volatile organic compounds, petroleum-related products, nitrates, and chloride and sodium. Sources of these contaminants include leaking storage tanks, accidental spills, landfills, road salting, and septic systems and lagoons. Elevated concentrations of mercury are found in fish tissue from streams and lakes throughout the study area.

Maine, Massachusetts, New Hampshire, Rhode Island↗
USGS2024

Framework for mapping liquefaction hazard–Targeted design ground motions

Liquefaction-induced ground failure poses substantial challenges to geotechnical earthquake engineering design. Current approaches for designing against liquefaction hazards, as specified in most seismic provisions, focus on estimating a liquefaction factor of safety ( 𝐹⁢𝑆𝐿 ) and typically characterize earthquake loading using design parameters based on probabilistic or deterministic ground motion levels. Because 𝐹⁢𝑆𝐿 is estimated deterministically, this basis of design neglects considerable uncertainties for estimating liquefaction triggering and its consequences and results in a lack of liquefaction-specific design criteria, particularly as structural design has advanced toward risk-targeted performance objectives. This study presents a framework for developing liquefaction-targeted design criteria based on a minimum acceptable return period of liquefaction, informed by probabilistic liquefaction hazard analysis (PLHA). PLHA quantifies annualized rates of liquefaction by considering contributions from (1) the full ground-motion probability space, and (2) uncertainties in liquefaction triggering using probabilistic models. PLHA is used in this study to characterize the current, effective return periods of 𝐹⁢𝑆𝐿 ( 𝑇𝑅,𝐹⁢𝑆 ) obtained from conventional liquefaction hazard analysis (CLHA) using uniform-hazard ground motions. 𝑇𝑅,𝐹⁢𝑆 is evaluated in a parametric study of nearly 100 sites throughout the conterminous United States. The results indicate large geographic variations in acceptable liquefaction hazard levels, with implied 𝑇𝑅,𝐹⁢𝑆 ranging between approximately 1,000 to 3,000 years. To address these inconsistencies without the computational demands of full PLHA, a framework is proposed for developing a liquefaction-targeted design peak ground acceleration, 𝑃⁢𝐺⁢𝐴𝐿 , for use in liquefaction models that result in consistent liquefaction design levels across all geographic locations. The mapped 𝑃⁢𝐺⁢𝐴𝐿 is shown to be somewhat sensitive to site-specific properties, and adjustment factors are developed and presented. The proposed 𝑃⁢𝐺⁢𝐴𝐿 mapping procedure produces 𝐹⁢𝑆𝐿 estimates that are consistent with those obtained from full PLHA at a target 𝑇𝑅,𝐹⁢𝑆 , providing a promising roadmap to incorporating PLHA concepts into current liquefaction design methods.

Journal of Geotechnical and Geoenvironmental Engin↗
USGS2026

Discrete element investigation of the influence of shallow soil density on the manifestations of strike-slip surface fault rupture

This study investigates the influence of soil relative density on strike-slip surface fault rupture manifestations using three-dimensional numerical simulations performed with the discrete element method (DEM). The simulations capture the formation of distinctive fault strands within complex flower structures using tens of millions of grains. The tendency for dense soils to localize shear manifests as multiple localized shear bands within wide zones of deformation in strike-slip fault rupture, whereas diffuse shear deformation develops within narrow zones in loose soils. The spatial extents of soil deformation are consistent between simulations having similar relative densities but with different quantities of grains. However, individual shears are more distinguishable in assemblages of finer grains than in assemblages of coarser grains. The simulations show the progressive development of new shears within the bounds of previously developed shears. Shear activity transitions inward as fault activity diminishes along the outermost shears and continues along newly developed shears until a vertically dipping throughgoing shear structure develops that accommodates most of the fault displacement thereon. The throughgoing fault develops at smaller fault displacements in looser soils because the first shear rupture propagates closer to the vertical direction and does not undergo as much inward translation of shear activity, as is observed in denser soils. In all simulations, ground surface uplift develops between nonintersecting active shears, and ground surface subsidence tends to develop where new shears intersect previous shears. The surface traces in these simulations are shown to be consistent with analog models and case histories of surface fault rupture occurring in different shallow subsurface materials. Although computationally costly, these modeling results are valuable for providing a strong numerical supplement to traditional analog models used to represent the mechanics of strike-slip zones in soil, and they provide quantifiable stresses and large-strain deformations throughout the model domain.

Journal of Geotechnical and Geoenvironmental Engin↗