Geology Reports⌕ Search

SEARCH · Geology Reports

Search Geology Reports

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,748 records · Page 94Linked to original sources
USGS1990

Large springs in the Valley and Ridge Province in Tennessee

Approximately 2,700 miscellaneous discharge measurements for 171 large springs in 28 counties of East Tennessee, predominantly within the Valley and Ridge physiographic province, were analyzed statistically and results tabulated to summarize data useful to the Appalachian Valleys-Piedmont Regional Aquifer System Analysis study. The number of measurements at each spring ranged from 1 to 65. Information from each spring includes station numbers, latitude, longitude, spring name and where data are sufficient, an estimate of the mean discharge and the discharge exceeded by 75%, 50%, and 25% of the miscellaneous measurements. Data are referenced to locations on a 1:1,000 ,000-scale map. The highest mean spring discharge was 32.2 cu ft/sec (14,5000 gallons/min).

Tennessee↗
USGS1990

Floods of February 1989 in Tennessee

Rainfall amounts of over 5 inches the night of February 13 and the morning of February 14, 1989, caused flooding in areas of Middle and West Tennessee. The towns of Lebanon in Middle Tennessee and Obion in West Tennessee were most severely affected. Most of the business district in Lebanon and many residential areas in Obion were flooded. Recurrence intervals for 24-hour rainfall totals were as high as 25 years at some sites but most peak discharges had recurrence intervals of less than 10 years. Rainfall amounts for the period February 13-20, 1989, peak stages and discharges for this flood, the peak of record, and a list of discharge measurements made during the flood are documented in this report.

Tennessee↗
USGS1990

Recharge rates and aquifer hydraulic characteristics for selected drainage basins in middle and east Tennessee

Quantitative information concerning aquifer hydrologic and hydraulic characteristics is needed to manage the development of ground-water resources. These characteristics are poorly defined for the bedrock aquifers in Middle and East Tennessee where demand for water is increasing. This report presents estimates of recharge rate, storage coefficient, diffusivity, and transmissivity for representative drainage basins in Middle and East Tennessee, as determined from analyses of stream-aquifer interactions. The drainage basins have been grouped according to the underlying major aquifer, then statistical descriptions applied to each group, in order to define area1 distribution of these characteristics. Aquifer recharge rates are estimated for representative low, average, and high flow years for 63 drainage basins using hydrograph analysis techniques. Net annual recharge during average flow years for all basins ranges from 4.1 to 16.8 in/yr (inches per year), with a mean value of 7.3 in. In general, recharge rates are highest for basins underlain by the Blue Ridge aquifer (mean value11.7 in/yr) and lowest for basins underlain by the Central Basin aquifer (mean value 5.6 in/yr). Mean recharge values for the Cumberland Plateau, Highland Rim, and Valley and Ridge aquifers are 6.5, 7.4, and 6.6 in/yr, respectively. Gravity drainage characterizes ground-water flow in most surficial bedrock aquifer in Tennessee. Accordingly, a gravity yield analysis, which compares concurrent water-level and streamflow hydrographs, was used to estimate aquifer storage coefficient for nine study basins. The basin estimates range from 0.002 to 0.140; however, most estimates are within a narrow range of values, from 0.01 to 0.025. Accordingly, storage coefficient is estimated to be 0.01 for all aquifers in Middle and East Tennessee, with the exception of the aquifer in the inner part of the Central Basin, for which storage coefficient is estimated to be 0.002. Estimates of aquifer hydraulic diffusivity are derived from estimates of the streamflow recession index and drainage density for 75 drainage basins; values range from 3,300 to 130,000 ft^2/d (feet squared per day). Basin-specific and site-specific estimates of transmissivity are computed from estimates of hydraulic diffusivity and specific-capacity test data, respectively. Basin-specific, or areal, estimates of transmissivity range from 22 to 1,300 ft^2/d, with a mean of 240 ft^2/d In general, areal transmissivity is highest for basins underlain by the Cumberland Plateau aquifer (mean value 480 ft^2/d) and lowest for basins underlain by the Central Basin aquifer (mean value 79 ft^2/d). Mean transmissivity values for the Highland Rim, Valley and Ridge, and Blue Ridge aquifer are 320,140, and 120 ft^2/d respectively. Site-specific estimates of transmissivity, computed from specific-capacity data from 118 test wells in Middle and East Tennessee range from 2 to 93,000 ft^2/d with a mean of 2,600 ft^2/d Mean transmissivity values for the Cumberland Plateau, Highland Rim, Central Basin, Valley and Ridge, and Blue Ridge aquifers are 2,800,1,200, 7,800, 390, and 65Oft Id, respectively.

Tennessee↗
USGS1990

Effects of storm-water runoff on local ground-water quality, Clarksville, Tennessee

Storm-related water-quality data were collected at a drainage-well site and at a spring site in Clarksville, Tennessee, to define the effects of storm-water runoff on the quality of ground water in the area. A dye-trace test verified the direct hydraulic connection between the drainage well and Mobley Spring. Samples of storm run off and spring flow were collected at these sites for nine storms during the period February to October 1988. Water samples were collected also from Mobley Spring and two other springs and two observation wells in the area during dry-weather conditions to assess the general quality of ground water in an urban karst terrain. Evaluation of the effect of storm-water runoff on the quality of local ground water is complicated by the presence of other sources of contaminants in the area Concentrations and load for most major constituents were much smaller in storm-water runoff at the drainage well than in the discharge of Mobley Spring, indicating that much of the chemical constituent load discharged from the spring comes from sources other than the drainage well. However, for some of the minor constituents associated with roadway runoff (arsenic, copper, lead, organic carbon, and oil and grease), the drainage well contributed relatively large amounts of these constituents to local ground water during storms. The close correlation between concentrations of total organic carbon and concentrations of most trace metals at the drainage-well and Mobley Spring sites indicates that these constituents are transported together. Many trace metals were flushed early during each runoff event. Mean storm loads for copper, lead, zinc, and four nutrient species (total nitrogen, ammonia nitrogen, total phosphorus, and orthophosphorus) in storm-water runoff at the drainage-well site were lower than mean storm load predicted from an existing regression model. The overprediction by the model may be a result of the small size of the drainage area relative to the range of drainage areas used in the development of the models, or to the below-normal amounts of rainfall during the period of sampling for this investigation. Loads& in storm-water runoff for 22 constituents were extrapolated from sampled storms to total loads for the period February to October 1988. Calculated loads for trace metals for the period ranged from 0.030pound.s for cadmium to 12pound.s for strontium. Loads of the primary nutrients ranged from 0.97pounds for nitrite as nitrogen to 34pounds of organic nitrogen. Storm-water quality at the drainage-well and Mobley Spring sites was compared to background water quality of the local aquifer; as characterized by dry-weather samples from three springs and two observation wells in the Clarksville area. Concentrations of total-recoverable cadmium, chromium, copper, lead, and nickel were higher in many stormwater samples from both the drainage-well and Mobley Spring sites than in samples from any other site. In addition, concentrations of total organic carbon, methylene blue active substances, and total-recoverable oil and grease were generally higher in storm-water samples from the drainage-well site than in any ground-water sample. Densities of fecal coliform and fecal streptococcus bacteria and concentrations of total recoverable iron, manganese, and methylene blue active substances in storm samples from the drainage-well site exceeded the maximum contaminant levels listed in Tennessee’s drinking-water standards (1988) by as much as 2,500 and 5,500 colonies per 100 milliliters, and 2.7, 0.29, and 0.05 milligrams per liter, respectively. Densities of fecal coliform and fecal streptococcus bacteria and concentrations of total-recoverable iron, manganese, and lead in storm samples from Mobley Spring exceeded the maximum contaminant levels by as much as 500 and 4,500 colonies per 100 milliliters, and 18.7,0.65, and 0.02 milligrams per liter, respectively. For iron, manganese, and bacteria, these undesirable levels are not necessarily attributable to storm-water recharge, because concentrations of these constituents also exceeded drinking-water standards in one or more of the dry-weather samples from selected springs and observation wells in the area.

Tennessee↗
USGS1990

Preconditioned Conjugate-Gradient 2 (PCG2), a computer program for solving ground-water flow equations

This report documents PCG2: a numerical code to be used with the U.S. Geological Survey modular three-dimensional, finite-difference, ground-water flow model. PCG2 uses the preconditioned conjugate-gradient method to solve the equations produced by the model for hydraulic head. Linear or nonlinear flow conditions may be simulated. PCG2 includes two reconditioning options: modified incomplete Cholesky preconditioning, which is efficient on scalar computers; and polynomial preconditioning, which requires less computer storage and, with modifications that depend on the computer used, is most efficient on vector computers. Convergence of the solver is determined using both head-change and residual criteria. Nonlinear problems are solved using Picard iterations. This documentation provides a description of the preconditioned conjugate gradient method and the two preconditioners, detailed instructions for linking PCG2 to the modular model, sample data inputs, a brief description of PCG2, and a FORTRAN listing.

Water-Resources Investigations Report↗
USGS1989

An investigation of shallow ground-water quality near East Fork Poplar Creek, Oak Ridge, Tennessee

Alluvial soils and fill materials in and near the floodplain of East Fork Poplar Creek in Oak Ridge, Tennessee, are contaminated with various trace metals (primarily mercury), organic compounds, and radionuclides that were lost to the stream as a result of past operations at the Y-12 Plant, a nuclear-processing facility located within the U.S. Department of Energy’s Oak Ridge Reservation. Observation wells were installed in the shallow (above bedrock) aquifer in and near the floodplain of East Fork Poplar Creek and water-quality samples were collected to determine if contaminants found in the soils and fill are also present in the shallow ground water. The shallow aquifer in the East Fork Poplar Creek flood plain consists primarily of alluvial silt and clay with lesser amounts of sand and gravel. Thickness of the shallow aquifer ranges from essentially zero to as much as 20 feet. A silty-clay glei horizon is present between the base of the alluvium and the top of bedrock at most flood-plain locations and, where present, likely impedes downward ground-water movement. Water in the shallow aquifer near East Fork Poplar Creek occurs under water-table conditions. Recharge to the shallow aquifer is principally from precipitation, and discharge is through springs and seeps to East Fork Poplar Creek and its tributaries. During spring, summer; and fall, evapotranspiration also accounts for the removal of water in storage in the shallow aquifer. Water levels in the shallow aquifer fluctuate seasonally in response to variations in recharge and evapotranspiration. Generally, the depth to water in the observation wells ranged from about 1 to 4 feet below land surface in late winter, and from about 2 to 7 feet below land surface in late fall. During extremely dry periods, the water table recedes below the top of bedrock in some flood-plain areas, possibly causing East Fork Poplar Creek to lose water to the shallow aquifer along some reaches. Contaminants found in water samples collected from several of the observation wells in concentrations (total and (or) total-recoverable) which equaled or exceeded drinking-water standards established by the U.S. Environmental Protection Agency are antimony, chromium, lead, mercury, selenium, total phenols, and strontium-90. Total and dissolved uranium concentrations exceeded 1.0 microgram per liter in samples from nearly 70 percent of the wells in the East Fork Poplar Creek flood plain. Organic compounds that were identified in low concentrations in samples from a few wells in the flood plain are: Arochlor 1260, benzo(a)anthracene, benzo(b)fluoranthene, chrysene, 3,3-dichlorobenzidine, di-n-butylphthalate, N-nitrosodiphenylamine, and pyrene. Water from one well in the East Fork Poplar Creek flood plain at a contaminated fill site contained 37and 8 micrograms per liter of trichloroethene and trans-1,2-dichloroethene, respectively. Comparison of the results of total and (or) total-recoverable trace-metal determinations with those from dissolved determinations demonstrates that elevated concentrations of these substances in water collected from several of the wells in the East Fork Poplar Creek flood plain resulted from sorption of trace metals (and possibly organic compounds and radionuclides) by fine sediment suspended in the samples. The occurrence of contaminated sediment in these samples is suspected to be the result of borehole contamination during well installation.

Tennessee↗
USGS1989

Techniques for simulating flood hydrographs and estimating flood volumes for ungaged basins in east and west Tennessee

A dimensionless hydrograph developed for a variety of basin conditions in Georgia was tested for its applicability to streams in East and West Tennessee by comparing it to a similar dimensionless hydrograph developed for streams in East and West Tennessee. Hydrographs of observed discharge at 83 streams in East Tennessee and 38 in West Tennessee were used in the study. Statistical analyses were performed by comparing simulated (or computed) hydrographs, derived by application of the Georgia dimensionless hydrograph, and dimensionless hydrographs developed from Tennessee data, with the observed hydrographs at 50 and 75% of their peak-flow widths. Results of the tests indicate that the Georgia dimensionless hydrography is virtually the same as the one developed for streams in East Tennessee, but that it is different from the dimensionless hydrograph developed for streams in West Tennessee. Because of the extensive testing of the Georgia dimensionless hydrograph, it was determined to be applicable for East Tennessee, whereas the dimensionless hydrograph developed from data on streams in West Tennessee was determined to be applicable in West Tennessee. As part of the dimensionless hydrograph development, an average lagtime in hours for each study basin, and the volume in inches of flood runoff for each flood event were computed. By use of multiple-regression analysis, equations were developed that relate basin lagtime to drainage area size, basin length, and percent impervious area. Similarly, flood volumes were related to drainage area size, peak discharge, and basin lagtime. These equations, along with the appropriate dimensionless hydrograph, can be used to estimate a typical (average) flood hydrograph and volume for recurrence-intervals up to 100 years at any ungaged site draining less than 50 sq mi in East and West Tennessee.

Tennessee↗
USGS1988

Geology of an area near Brentwood, Williamson County, Tennessee

The lithology and geologic structure of an area near Brentwood, Williamson County, Tennessee, were studied to define the potential aquifers and confining units of the ground-water flow system. Four formations were identified. They are, in descending order, the Bigby-Cannon Limestone, the Hermitage Formation, the Carters Limestone, and the Lebanon Limestone. The Bigby-Cannon Limestone and the Carters Limestone are potential aquifers. The Hermitage Formation and the Lebanon Limestone are confining units. The Bigby-Cannon Limestone and the Hermitage Formation have been affected by recent erosion. Any variation of the Carters Limestone is controlled by pre-Carters erosion of the top of the Lebanon Limestone. The thickness of the Carters Limestone ranges from 65 to 79 feet. Structurally, the area reflects the regional northwest dip. A small scale anti-cline-syncline pair also is evident. This feature is not a result of erosion and also occurs in the T-3 bentonite bed in the Carters Limestone.

Tennessee↗
USGS1986

Water-quality appraisal of NASQAN stations below impoundments, eastern Tennessee

The National Stream Quality Accounting Network (NASQAN) is a network of stations at which systematic and continuing water-quality data are collected. Major objectives of this U.S. Geological Survey program are (1) to depict areal variability of streamflow and water-quality conditions nationwide on a year-by-year basis and (2) to detect long-term changes in streamflow and stream quality. Several NASQAN stations in East Tennessee are downstream from impoundments which have a significant effect on water quality. NASQAN data obtained from the Tennessee River below Watts Bar Dam and the Clinch River below Melton Hill Dam were compared to water-quality data from the basins upstream. The comparison indicates that NASQAN data obtained below impoundment may not be adequate to describe a composite picture of water quality in the accounting unit. Detention time of storage in the impoundments is believed to moderate the range of constituent values observed at the NASQAN stations. Data obtained upstream and downstream from Watts Bar Dam indicate that the water sampled at the NASQAN station comes from stratified layers of the impoundment and is not representative of an integrated sample of water from the impoundment. Values of total recoverable iron suggest that, because of adsorption to sediments in impoundments, some constituents are not accurately described by sampling below impoundments. Relations between water-quality constituents and flow at stations on the Clinch River and Tennessee River are not well defined due to regulation. Direct load computations for many constituents were therefore not possible, which diminished the utility of data from these NASQAN stations to account for quantity versus quality of the water. Load computations were only possible for ionic constituents through use of a continuous specific-conductance record as an intermediary. Compensation for the effects of discharge prior to application of the Seasonal Kendall test for trends could not be done and identification of trends in water-quality constituents caused by some process (source) change was not possible. Some water-quality trends indicated by data from the Clinch and Tennessee Rivers might reflect the decreasing trend in discharge during the 1972-82 water years. Thus the stations below Watts Bar Dam and below Melton Hill Dam do not adequately meet the NASQAN objective to detect and assess long-term changes in stream quality.

Tennessee↗
USGS1986

Regionalization of low-flow characteristics of Tennessee streams

Procedures for estimating 3-day 2-year, 3-day 10-year, 3-day 20-year, and 7-day 10-year low flows at ungaged stream sites in Tennessee are based on surface geology and drainage area size. One set of equations applies to west Tennessee streams, and another set applies to central and east Tennessee streams. The equations do not apply to streams where flow is significantly altered by activities of man. Standard errors of estimate of equations for west Tennessee are 24 to 32% and for central and east Tennessee 31 to 35%. Streamflow recession indexes, in days/log cycle, are used to account for effects of geology of the drainage basin on low flow of streams. The indexes in Tennessee range from 32 days/log cycle for clay and shale to 350 days/log cycle for gravel and sand, indicating different aquifer characteristics of the geologic units that sustain streamflows during periods of no surface runoff. Streamflow recession rate depends primarily on transmissivity and storage characteristics of the aquifers, and the average distance from stream channels to basin divides. Geology and drainage basin size are the most significant variables affecting low flow in Tennessee streams according to regression analyses. (Author 's abstract)

Tennessee↗
USGS1986

Potential for leakage among principal aquifers in the Memphis area, Tennessee

The principal aquifers in the Memphis area consist primarily of sand or sand and gravel, and the confining beds consist of clay, silt, sand, and lignite. The Jackson Formation and upper part of the Claiborne Group serve as the confining bed separating the water table aquifers from the Memphis Sand; the Flour Island Formation separates the Memphis Sand from the Fort Pillow Sand. Differences in total hydraulic head among the principal aquifers in the Memphis urban area result in vertical hydraulic gradients which create a potential for inter-aquifer exchange of water. Throughout this area, the gradient is downward from the water table aquifers to the Memphis Sand. In the central part of the Memphis urban area, the vertical hydraulic gradient is upward from the Fort Pillow Sand to the Memphis Sand, and in the eastern and western parts, it is downward from the Memphis Sand to the Fort Pillow Sand. The vertical distribution of carbon-14 data for water from the fluvial deposits, Memphis Sand, and Fort Pillow Sand shows an increase in the relative age of the water with depth. The areal distribution of carbon-14 data for water from the upper part of the Memphis Sand indicates that relatively recent water has been brought into the major cone of depression in the potentiometric surface of the Memphis Sand, either by horizontal movement or from downward vertical leakage. The normal, near-surface geothermal gradient in the Memphis area was determined to be 0.6 C/100 ft. Deviations from the normal geothermal gradient, in areas affected by intense pumping from the Memphis Sand, indicate that downward vertical leakage occurs from the water table aquifers through the Jackson-upper Claiborne confining bed to the Memphis Sand. The velocity of downward vertical leakage of water from the Memphis Sand through the Flour Island confining bed to the Fort Pillow Sand was determined to be 0.0066 ft/day by analysis of borehole temperature data from an observation well in the northeastern part of the Memphis area. From this velocity and the head difference between the Memphis Sand and the Fort Pillow Sand at this locality, the hydraulic conductivity of the Flour Island confining bed was determined to be 0.00114 ft/day. (Lantz-PTT)

Tennessee↗
USGS1985

Low flows and flow duration of Tennessee streams through 1981

Estimates of low-flow characteristics and flow duration for the period of record at continuous-record streamflow gages are essential in hydrologic studies and water-resources management. This report provides estimates of low flow for 1, 3, 7, 14, 30, 60, and 90 consecutive days for recurrence intervals of 2, 5, 10, and 20 years for continuous-record streamflow gages. These estimates were used in correlation methods to estimate low flow at partial-record streamflow sites for 1, 3, and 7 consecutive days for a recurrence interval of 10 years; and 3 consecutive days for a recurrence interval of 20 years.

Tennessee↗
USGS1984

Techniques for estimating magnitude and frequency of floods on streams in Indiana

Equations are presented for estimating the magnitude and frequency of floods at ungaged sites on unregulated and nonurban streams in Indiana. The equations were developed by multiple-regression, analysis of basin characteristics and peak-flow statistical data from 242 gaged locations in Indiana, Ohio, and Illinois. The State of Indiana was divided into seven areas on the basis of the regression analysis. A set of equations for estimating peak discharges with recurrence intervals of 2, IO, 25, 50, and 100 years was developed for each area. Significant basin characteristics in the equations are drainage area, channel length, channel slope, mean annual precipitation, storage, precipitation intensity, and a runoff coefficient. Standard errors of estimate for the equations range from 24 to 45 percent. Methods are also presented for estimating flood magnitude and frequency at sites on gaged streams. Flood-frequency data based on observed peaks are given for 270 gaged locations. Twenty of these are on regulated streams, and six are on urban streams. Basin characteristics are also included car 245 of the gaged locations on unregulated and nonurban streams. No techniques are given for estimating flood magnitude and frequency at ungaged sites on regulated or urban streams. A rainfall-runoff model was tlsed to synthesize long-term peak data at 11 gaged locations on small streams. Flood-frequency curves developed from the long-term synthetic data were combined with curves based on short-term observed data to provide weighted estimates of flood magnitude and frequency at the rainfall-runoff stations.

Indiana↗
USGS1983

Use of digital land-cover data from the Landsat satellite in estimating streamflow characteristics in the Cumberland Plateau of Tennessee

Characteristics of Streamflow at ungaged sites in coal-mining areas of the Cumberland Plateau may be estimated with regression equations that relate streamflow characteristics to the physiographic and climatic characteristics of the corresponding drainage basins. An experiment was performed to compare the accuracy of equations using basin characteristics derived from maps and climatological records (control group equations) with the accuracy of equations using basin characteristics derived from digital processing of Landsat spectral data as well as maps and climatological records (experimental group equations). Results of this experiment show that (with the exception of low flows and four of six annual peak logarithms) drainage area can explain more than 90 percent of the variance in all streamflow characteristics in both groups of equations. Seventeen of 39 experimental group equations that have two basin characteristics each are different from the corresponding control group equations. Five of the 17 differing experimental group equations have no counterpart in the control group because of lack of significance in control group basin characteristics, seven are slightly more accurate, and five are not measurably different in accuracy. When the equations in both groups are arranged into six flow categories, there is no substantial difference in accuracy between equations using basin characteristics derived from maps and climatological records (control group) and equations using basin characteristics derived from Landsat tapes as well as maps and climatological records (experimental group) for this particular study area, the Cumberland Plateau of Tennessee.

Tennessee↗
USGS1983

Technique for estimating depth of floods in Tennessee

Estimates of flood depths are needed for design of roadways across flood plains and for other types of construction along streams. Equations for estimating flood depths in Tennessee were derived using data for 150 gaging stations. The equations are based on drainage basin size and can be used to estimate depths of the 10-year and 100-year floods for four hydrologic areas. A method also was developed for estimating depth of floods having recurrence intervals between 10 and 100 years. Standard errors range from 22 to 30 percent for the 10-year depth equations and from 23 to 30 percent for the 100-year depth equations.

Tennessee↗
USGS1983

Base flow and ground water in upper Sweetwater Valley, Tennessee

The upper Sweetwater Valley area has a flow system with complex interaction between surface and ground water. A water budget study indicated that during dry years approximately three-fourths of the annual flow to Sweetwater Creek may be derived from ground-water sources. Hydrograph analysis showed seasonal variation of recharge to the ground-water flow system. Streamflow records were analyzed to estimate the frequency of low flow of Sweetwater Creek at river mile 16.7, and indicated the lowest average flow for 1 day in 20 years to be about 5.1 cubic feet per second. Two periods of base-flow measurements of Sweetwater Creek identified channel reaches with significant gains and losses of streamflow. Base flow measurements also showed interbasin transfer of water among sub-basins of the valley. Major flow surpluses were associated with areas in which the majority of flow originated at a spring. Topographically low areas adjacent to the main stem of Sweetwater Creek generally have surplus flow. Topographically higher areas generally have deficient surface outflow unless significant spring flow occurs in the basin. Ground-water recharge occurs by water draining into sinkholes, faults, and fractures. Ground-water flow is regionally diffused across formation strikes from the topographically low areas unless the water is exposed to highly permeable formations or impervious formations. Ground water infiltrates the highly permeable formations and flows along strike. Ground water encountering impervious formations may discharge at small springs at the contact, or may reroute along the contact if the upgradient rock is sufficiently permeable or has well developed secondary porosity. Groundwater discharges to streams at innumerable seeps and at a few large springs. Areas of ground-water flow up-gradient of large springs are hypothesized as likely areas of significant ground-water reservoirs.

Tennessee↗