Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “SOIL”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89Linked to original sources

Remote detection of geochemical soil anomalies

This paper describes a preliminary experiment that was made to compare the spectral reflectance from trees growing in soil over a mineral deposit with reflectance from trees of the same species growing in a nearby unmineralized area. Although the measurements were made on a relatively small number of trees, some significant differences were obtained and the over-all results are encouraging enough to warrant additional studies. Preliminary results suggest that measurement of spectral reflectance may become a dramatic new way of detecting geochemical soil anomalies by remote means in tree-covered areas.

Conference Paper↗

Shear wave velocity investigation of soil liquefaction sites from the Tangshan, China M7.8 earthquake of 1976 using active and passive surface wave methods

An initial investigation of soil liquefaction sites from the July, 28 1976 Tangshan M7.8 earthquake was conducted between 1976 and 1978 by the National Ministry of Railways, China. These data are the basis of the ‘Chinese Method’ for assessment of liquefaction potential of silty-sand deposits, and are an important component of the worldwide data set for modern probabilistic methods for assessment of soil liquefaction using Bayesian updating and system reliability tools. We revisited 26 sites identified in the maps and published 198 report of the Ministry of Railways in order to investigate these locations with a suite of active- and passive-array surface wave methods. These sites are clustered along the north coast of the Bo Hai Sea in three areas: Lutai, Tianjin; Tangshan City and outlying village, Hebei; and Luannan county, Hebei. First, we gathered and evaluated the Rayleigh wave dispersion characteristics of the ground by comparing dispersion curves from the active source harmonic wave-spectral analysis of surface waves (SASW) method and the passive array Spatial Auto-Correlation method (SPAC). The dispersive properties of the liquefied ground as measured by these two methods were found to be almost identical. These tests were hybridized and the data sets merged in order to invert of shear wave velocities for analysis of liquefaction potential using a probabilistic framework. The data from high-values of seismic intensity near Tangshan city to low-intensities distant of the event in Luannan County segregate out into clusters of liquefied and non liquefied points clearly separated by liquefaction boundary curves developed from a large global data set of 310 sites

Tangshan↗

Helium in soil gases of the Roosevelt Hot Springs Known Geothermal Resource Ares, Beaver County, Utah

Soil samples were collected in two parallel traverses across the Dome fault zone of the Roosevelt Hot Springs Known Geothermal Resource Area. The samples were sealed in air-tight aluminum cans, and the soil gas was allowed to equilibrate with the atmospheric air in the cans. Gas from the cans was analyzed by mass spectrometry. Samples collected over faults contained anomalously high concentrations of helium. Samples collected close to a geothermal well 884 m deep contained more helium than samples collected near another geothermal well 1370 m deep.

Utah↗

An orientation soil survey at the Pebble Cu-Au-Mo porphyry deposit, Alaska

Soil samples were collected in 2007 and 2008 along three traverses across the giant Pebble Cu-Au-Mo porphyry deposit. Within each soil pit, four subsamples were collected following recommended protocols for each of ten commonly-used and proprietary leach/digestion techniques. The significance of geochemical patterns generated by these techniques was classified by visual inspection of plots showing individual element concentration by each analytical method along the 2007 traverse. A simple matrix by element versus method, populated with a value based on the significance classification, provides a method for ranking the utility of methods and elements at this deposit. The interpretation of a complex multi-element dataset derived from multiple analytical techniques is challenging. An example of vanadium results from a single leach technique is used to illustrate the several possible interpretations of the data.

Alaska↗

Trace-metal variation in soils and sagebrush in the Powder River Basin, Wyoming and Montana

A reconnaissance study of 28 trace metals in samples of surface soil (0-2.5 cm deep), subsurface soil (15-20 cm deep), and big sagebrush ( Artemisia tridentata ) that were collected from the Powder River Basin in Wyoming and Montana indicates that little variation occurs in nature at scales greater than about 35 km. This general lack of broadscale variation suggests that simple summary statistics for these materials could provide basinwide geochemical baselines for use in monitoring secular changes in the local geochemical environment. Samples of big sagebrush near the Dave Johnston Power Plant at the southern edge of the basin exhibit statistically significant reductions of strontium, vanadium, uranium, and selenium eastward from the plant.

Montana, Wyoming↗

An improved ion-selective electrode method for the rapid determination of fluorine in rocks and soil

An improved method based on an ion-selective electrode technique for the analysis of fluorine in rocks and soils is presented. Analyses are made by using a sodium carbonate-potassium carbonate fusion and a citric acid dissolution of the fuseate. Prior to determining the fluorine concentration by a standard-addition procedure, sodium citrate buffer is added to the solution. The proposed method yields fluorine values in agreement with known values for standard rocks. Values of this method are also presented for six geochemical exploration rock-and-soil reference samples and compared to those from other ion-selective electrode techniques. Fifty samples can be analyzed in 1 person-day. The sensitivity of the method is 100 parts per million, and samples containing up to 45 percent fluorine have been successfully analyzed.

Journal of Research of the U.S. Geological Survey↗

USGS/EPA collection protocol for bacterial pathogens in soil

This Sample Collection Procedure (SCP) describes the activities and considerations for the collection of bacterial pathogens from representative surface soil samples (0-5 cm). This sampling depth can be reached without the use of a drill rig, direct-push technology, or other mechanized equipment. This procedure can be used in most soil types but is limited to sampling at or near the ground surface. This protocol has components for two different types of sampling applications: (1) typical sampling, when there is no suspicion of contamination (e.g., surveillance or background studies); and (2) in response to known or suspected accidental contamination (e.g., the presence of animal carcasses). This protocol does not cover sampling in response to a suspected bioterrorist or intentional release event. Surface material is removed to the required depth (0-5 cm) and clean trowel or 50 ml sample tube is used to collect the sample. Sample containers are sealed, bagged, and shipped to the laboratory for analysis. Associated documentation, including a Field Data Log and Chain-of-Custody are also included in this document.

Report↗

Preserving soil organic carbon in prairie wetlands of central North America

Wetlands of the Prairie Pothole Region (PPR) in the Great Plains of central North America are numerous, densely distributed, and have highly productive plant and animal communities (Photo 49). When in a natural, unaltered condition, these wetlands store relatively large amounts of organic carbon in their soils (Photo 50). Human alterations, such as extensive drainage and land-use conversion for agriculture (Figure 7), have been linked with the loss of soil organic carbon (SOC) and associated emission of carbon dioxide (CO 2 ), as well as impacts to other ecosystem services provided by these wetlands, such as wildlife and waterfowl habitat, plant biodiversity, flood mitigation, groundwater recharge, nutrient removal and retention, and recreation (Gleason et al., 2011). It has been estimated that more than half of the wetlands of the PPR have been lost due to drainage and other disturbances, with losses approaching 90 percent in some areas (Dahl, 2014; Serran et al., 2018). The goal of this case study was to identify land-management strategies that are consistent with maintaining and increasing SOC stocks of PPR wetlands. Two overarching strategies generally are promoted to preserve and enhance SOC stocks of PPR wetlands: avoided drainage and rewetting or restoration. Avoided drainage involves protecting natural, unaltered wetlands from impacts of human actives with the purpose of retaining wetland functions and services such as carbon storage. Rewetting or restoration involves reestablishing natural hydrology and land use with the purpose of enhancing wetland functions and services that were previously lost due to human activities. Avoided drainage provides immediate and long-lasting benefits, while replenishing SOC through rewetting and restoration requires many decades. Both strategies are associated with higher methane (CH 4 ) emissions but lower CO 2 and nitrous oxide (N 2 O) emissions.

Alberta, Iowa, Manitoba, Minnesota, Montana, North↗

The soil creep-curved tree fallacy

No evidence has been found in eastern deciduous forests to substantiate statements that curved tree trunks, downslope tilted tree trunks, and upslope trailing tree root systems are the result of soil creep. Curvature and tilting of trunks are described as geotropic and phototropic responses to physical and physiological conditions unrelated to soil creep. The occurrence of upslope trailing of roots has not been demonstrated.

Journal of Research of the U.S. Geological Survey↗

Shallow water table fluctuations in relation to soil penetration resistance

Hydrologic modeling of catchments is frequently hampered by lack of information on subsurface stratigraphy and zones of preferred flow. We evaluated the usefulness of soil penetration resistance, easily measured by a dynamic cone penetrometer, together with measurements of ground water level fluctuations, as a cost-effective means to infer subsurface flow patterns. At our field site at Sleepers River, Vermont, penetration resistance was lowest in the surficial 10 to 30 cm, then typically increased to a local maximum at 60 to 80 cm, which we interpreted as the soil/till interface. Below this depth usually lies a zone of decreased resistance in the till, giving way to either a gradual or abrupt increase in resistance toward the bedrock surface at 1 to 4.5 m depth. Penetration resistance had a weak but significant negative correlation with saturated hydraulic conductivity determined by bail tests (r 2 = 0.25, p < 0.05). At many wells, monthly ground water levels tended to cluster at or just above the resistant zone near the soil/till interface. Chemical and isotopic dynamics in nested wells finished above and below the resistant zone suggest that the zone may temporarily isolate the deeper ground water reservoir from meltwater inputs, which were clearly identified by low δ 18 O values. In ground water discharge zones, δ 18 O values tended to converge throughout the profile. In contrast, dissolved organic carbon (DOC) maintained a gradient of increasing concentration toward land surface, even in otherwise well-mixed waters, reflecting its rapid release from organic horizons. Understanding the effect of soil penetration resistance on ground water behavior may be useful in future catchment modeling efforts.

Vermont↗

Effects of stochastically-simulated near-fault ground motions on soil liquefaction

The scarcity of historically recorded near-fault ground motions poses a challenge to systematically understanding the influence of near-fault effects on various types of seismic demands for engineering purposes. In particular, the current state of knowledge of the influence of ground-shaking intensity on soil liquefaction and its consequences does not specifically account for the effects of near-fault ground motion characteristics. In this study, the influence of near-fault ground motions on liquefaction triggering and lateral spreading are investigated using non-linear modeling of a hypothetical liquefiable soil column in the finite-element computational platform OpenSees subjected to simulated ground motion time series that represent strong earthquake shaking in the near field. The simulated ground motion time series and resulting datasets are based on a parametric stochastic model and are developed for a range of source and path parameters to represent a realistic variability of ground motion characteristics. Dependencies between ground motion intensity measures (IMs) and liquefaction demand parameters are investigated for near-fault pulse and nonpulse-like ground motion sets. Evolutionary IMs, such as cumulative absolute velocity (CAV) and the time-varying magnitude-adjusted peak ground acceleration (PGAM), are considered in developing liquefaction triggering probability density functions. Post-liquefaction triggering responses such as lateral spreading displacements are examined in relation to PGA M and CAV. The ground motion simulations are validated by comparing their liquefaction-capacity PGA M fragilities and post-triggering CAV vulnerability relationships to historical records from the 1994 Northridge earthquake in California, USA. Finally, a path forward for future studies that includes finding systematic differences in the IM-liquefaction demand relationships between near-fault and far-field stochastic ground motion sets is outlined.

Conference Paper↗

Resiliency of biological soil crusts and vascular plants varies among morphogroups with disturbance intensity

Background and aims Disturbance affects the ability of organisms to persist on a site, and disturbance history acts as a filter of community composition. This is true for vascular plants and morphological groups of biocrusts, which respond differently to disturbance. Although functioning arid ecosystems include both groups , filtering of morphological groups of biocrusts has not previously been compared simultaneously with the responses of vascular plants. Methods Using a chronosequence approach, cover of vascular plants and biocrusts was examined across chronic disturbance gradients related to invasion by exotic species and grazing by livestock, following the acute disturbance of fire using paired burned and unburned plots in Wyoming big sagebrush on 99 plots. Results Cover of vascular plants and biocrusts was related to disturbance more so than abiotic factors of precipitation following fire, soil chemistry, percent coarse fragment and heat load index. Over time since fire of 12–23 years, we saw recovery of early successional groups: short mosses, shallow-rooted perennial grasses and annual forbs. Cover of deep and shallow-rooted perennial grasses and annual forbs increased in cover with intermediate levels of disturbance. Perennial forbs lacked a clear relationship with disturbance. Biocrusts decreased in cover with less disturbance when compared with perennial herbaceous plants but differed in sensitivities. Tall mosses were less sensitive to disturbance compared with lichens. Short mosses increased with some disturbance. Conclusions Morphological groups of biocrusts and vascular plants are eliminated with increasing variability in the size of gaps between perennials represented by the standard deviation of gaps between perennials. The inclusion of both groups in assessments of ecosystem recovery following disturbance addresses the fact that recovery of either group does not happen in isolation from the other but with interacting contributions to ecosystem functions.

Plant and Soil↗

Examination of differences between three SPT-based seismic soil liquefaction triggering relationships

The preceding companion paper presented the updating of the seismic soil liquefaction triggering relationship of Cetin et al. [1], and compared the resulting updated relationship with the earlier version. In this second paper, a detailed cross-comparison is made between three triggering relationships: (1) Seed et al. [2], as slightly updated by the NCEER Working Group (Youd et al. [3]), (2) Boulanger and Idriss [4], and (3) Cetin et al. [5]. Differences between these three triggering relationships, and the apparent causes of them are examined. Also studied are the impacts of these differences on levels of conservatism with regard to evaluation of liquefaction triggering hazard, and the resulting risks for engineering projects.

Soil Dynamics and Earthquake Engineering↗

The feasibility of using sequential extraction techniques for As and Se in soils and sediments

Laboratory experiments were conducted with well-characterized minerals to test the applicability of selective extraction schemes for Se and As partitioning in soils and sediments. Two specific steps were tested: the reductive dissolution of amorphous iron oxides and the oxidation of organic material. Selenium and As associated with amorphous iron oxides were usually not found in solution after reductive dissolution, due to readsorption onto other minerals unaffected by the extractant. Oxidants intended to dissolve organic material also oxidized Se(IV) adsorbed on a mineral to Se(VI), causing the release of Se(VI) to the extractant solution.

Soil Science Society of America Journal↗

Semiempirical model of soil water hysteresis

In order to represent hysteretic soil water retention curves accurately using as few measurements as possible, a new semiempirical model has been developed. It has two postulates related to physical characteristics of the medium, and two parameters, each with a definite physical interpretation, whose values are determined empirically for a given porous medium. One parameter represents the fraction of the pore space that is not subject to Haines jump hysteresis. Its associated postulate is that a single value of this parameter characterizes a given medium, or, equivalently, that the medium is self-similar with respect to the division between hysteretic and nonhysteretic pore space. The second parameter is the effective body-to-neck size ratio of the medium's largest pore. The second postulate specifies a particular relation between the size distributions of pore bodies and of pore necks. Tests of the model show that it provides high-quality optimized fits to measured water content vs. matric pressure wetting curves for a wide variety of media. The parameter values obtained through optimization correlate plausibly with such media properties as uniformity of particles, complexity of structure, and degree of compaction. A practical use of this model is to provide a complete simulated main wetting curve for a medium where only a main drying curve and two points on the wetting curve have been measured. With additional development, it may be possible to do without the two measured wetting points if parameters can be evaluated from other measurements or known properties of the medium.

Soil Science Society of America Journal↗

Land subsidence in drained histosols and highly organic mineral soils of California

This study was conducted to determine historical trends in subsidence in the Sacramento-San Joaquin Delta and their environmental controls. In the western Delta, average subsidence rates were 2.3 cm yr-1 from 1910 to 1.5 cm yr-1 from 1952 to 1988. Spatially variability in subsidence was correlated with organic matter content of the soil which in turn was related to the depositional and drainage history of the Delta. Subsidence rates appaeared to be independent of crops grown.

California↗

Estimating the effect of winter cover crops on nitrogen leaching using cost-share enrollment data, satellite remote sensing, and Soil and Water Assessment Tool (SWAT) modeling

This study employed a novel combination of data (winter cover crop cost-share enrollment records, satellite remote sensing of wintertime vegetation, and results of Soil and Water Assessment Tool (SWAT) water quality simulations) to estimate the environmental performance of winter cover crops (WCC) at the watershed scale, from 2008 through 2017, within the Tuckahoe sub-watershed of the Choptank River. The Choptank is a river basin within the Chesapeake Bay watershed and, as a focus watershed for the U.S. Department of Agriculture’s Conservation Effects Assessment Project (CEAP), has been the subject of considerable study assessing linkages between land use and water quality. Farm enrollment data from the Maryland Agricultural Cost Share (MACS) program documented a strong increase in the use of WCC within the Tuckahoe watershed during the study period, from 27% of corn fields and 9% of soybean fields in 2008 to 89% of corn fields and 46% of soybean fields in 2016. Satellite remote sensing of wintertime ground cover detected increased wintertime vegetation following corn crops, in comparison to full season and double cropped soybean, consistent with patterns of cover crop implementation. Although inter-annual variation in climate strongly affected observed levels of vegetation, with warm winters resulting in increased vegetative cover, a 30-year analysis of wintertime greenness revealed significant increases in wintertime vegetation associated increased adoption of WCC. The predominant WCC species recorded by the MACS program as planted in the Tuckahoe watershed were wheat (68.1%), barley (16.1%), and rye (7.2%). The MACS WCC enrollment data were combined with output from the SWAT model, calibrated to streamflow and nutrient loading from the Tuckahoe watershed, to estimate water quality impacts based on known distribution of cover crop species and planting dates (2008 to 2017). Results indicated a 25% overall 10-year reduction in nitrate leaching from cropland resulting from cover crop adoption, rising to an estimated 38% load reduction in 2016 when 64% of fields were planted to cover crops. A large portion of WCC (39.3%) were planted late (after October 15) and planted to wheat (68.1%). Increased environmental benefits would be achieved by shifting agronomic methods away from late-planted wheat.

Delaware, Maryland↗