SEARCH · Geology Reports

Results for “Progress Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88Linked to original sources

USGS2010

Channel-conveyance capacity, channel change, and sediment transport in the lower Puyallup, White, and Carbon Rivers, western Washington

Draining the volcanic, glaciated terrain of Mount Rainier, Washington, the Puyallup, White, and Carbon Rivers convey copious volumes of water and sediment down to Commencement Bay in Puget Sound. Recent flooding in the lowland river system has renewed interest in understanding sediment transport and its effects on flow conveyance throughout the lower drainage basin. Bathymetric and topographic data for 156 cross sections were surveyed in the lower Puyallup River system by the U.S. Geological Survey (USGS) and were compared with similar datasets collected in 1984. Regions of significant aggradation were measured along the Puyallup and White Rivers. Between 1984 and 2009, aggradation totals as measured by changes in average channel elevation were as much as 7.5, 6.5, and 2 feet on the Puyallup, White, and Carbon Rivers, respectively. These aggrading river sections correlated with decreasing slopes in riverbeds where the rivers exit relatively confined sections in the upper drainage and enter the relatively unconstricted valleys of the low-gradient Puget Lowland. Measured grain-size distributions from each riverbed showed a progressive fining downstream. Analysis of stage-discharge relations at streamflow-gaging stations along rivers draining Mount Rainier demonstrated the dynamic nature of channel morphology on river courses influenced by glaciated, volcanic terrain. The greatest rates of aggradation since the 1980s were in the Nisqually River near National (5.0 inches per year) and the White River near Auburn (1.8 inches per year). Less pronounced aggradation was measured on the Puyallup River and the White River just downstream of Mud Mountain Dam. The largest measured rate of incision was measured in the Cowlitz River at Packwood (5.0 inches per year). Channel-conveyance capacity estimated using a one-dimensional hydraulic model decreased in some river reaches since 1984. The reach exhibiting the largest decrease (about 20-50 percent) in channel-conveyance capacity was the White River between R Street Bridge and the Lake Tapps return, a reach affected by recent flooding. Conveyance capacity also decreased in sections of the Puyallup River. Conveyance capacity was mostly unchanged along other study reaches. Bedload transport was simulated throughout the entire river network and consistent with other observations and analyses, the hydraulic model showed that the upper Puyallup and White Rivers tended to accumulate sediment. Accuracy of the bedload-transport modeling, however, was limited due to a scarcity of sediment-transport data sets from the Puyallup system, mantling of sand over cobbles in the lower Puyallup and White Rivers, and overall uncertainty in modeling sediment transport in gravel-bedded rivers. Consequently, the output results from the model were treated as more qualitative in value, useful in comparing geomorphic trends within different river reaches, but not accurate in producing precise predictions of mass of sediment moved or deposited. The hydraulic model and the bedload-transport component were useful for analyzing proposed river-management options, if surveyed cross sections adequately represented the river-management site and proposed management options. The hydraulic model showed that setback levees would provide greater flood protection than gravel-bar scalping after the initial project construction and for some time thereafter, although the model was not accurate enough to quantify the length of time of the flood protection. The greatest hydraulic benefit from setback levees would be a substantial increase in the effective channel-conveyance area. By widening the distance between levees, the new floodplain would accommodate larger increases in discharge with relatively small incremental increases in stage. Model simulation results indicate that the hydraulic benefit from a setback levee also would be long-lived and would effectively compensate for increased deposition within the setback reach

Scientific Investigations Report↗

USGS1983

Late Proterozoic island-arc complexes and tectonic belts in the southern part of the Arabian Shield, Kingdom of Saudi Arabia

Two main subdivisions of layered rocks are recognized in the southern Arabian Shield south of lat 22? N. These are an older ensimatic-arc complex, which formed 1100-800 m.y. ago, and a younger marginal-arc complex, which formed 800-690 m.y. ago. The older ensimatic-arc complex, located in the southwestern part of the Shield, includes graywacke and mafic to intermediate volcanic rocks of the essentially contemporaneous Baish, Bahah, and Jiddah groups. Although the younger arc complex is also dominantly ensimatic in character, it is also partly superimposed over the older ensimaticarc complex. The superimposed portions of the younger arc complex are represented by the Ablah, Samran, and possibly the Ararat groups. The ensimatic portion of the younger arc group is represented by the Halaban group, which was deposited to the east and northeast of the older ensimatic-arc complex. The Halaban group includes andesitic and dacitic volcanic rocks and associated clastic sedimentary rocks. The layered rocks of both arc complexes are intruded by dioritic (quartz diorite, tonalite, trondhjemite) plutonic rocks. The southern Shield is also subdivided into a number of structurally bounded, north-trending tectonic belts. Within the older ensimatic complex, three belts are recognized. From west to east, these are the Lith, Bidah, and Tayyah belts. Within these three belts, progressive facies changes indicate a gradation from deep-water facies in the south to shallow-water or-terrestrial facies in the north. The distribution of dioritic batholiths, as well as the distribution of layered-rock facies, suggests a northwest-trending axis for the older ensimatic-arc complex. The younger arc complex is present within six belts, the Makkah source papers. In Fleck and others (1980), the term 'quartz diorite' includes both tonalite and quartz diorite as defined in the International Union of Geological Sciences (IUGS) system of plutonic rock classification (Streckeisen, 1973). Initial 87Sr/86Sr ratios are not included in the appendix, but all rocks more than 660 m.y. old have initial ratios in the range 0.7021-0.7035, with only two greater than 0.7030. Thus, nothing in the Rb-Sr data suggests involvement of an older continental crust during the evolution of the southern Shield. A lead isotope study of ore minerals and potassium feldspars of the Arabian Shield by Stacey and others (1980) also suggests that no older (Archean to early Proterozoic) evolved continental-type crust underlies the southern Shield. An early summary of mapping (Schmidt and others, 1973) suggests that older sialic basement underlies the late Proterozoic layered rocks in the southern Shield. However, subsequent-mapping and the isotopic studies cited above have established that all of these rocks are of late Proterozoic age and that all rocks of the southern Shield that are more than 660 m.y. old have ensimatic or mantle isotopic characteristics. Figure 2 shows, with only two exceptions, that rocks more than 800 m.y. old are present west of the boundary separating the Tayyah and Khadra belts. The exceptions are two poorly controlled Rb-Sr ages obtained by Fleck (1980) on two quartz diorite plutons in the Malahah region (appendix 1, localities 26 and 27). Preliminary uranium-thorium zircon data of Stacey now suggest that one of these quartz diorite plutons (locality 26) has an age of approximately 640 m.y. Therefore, we prefer to discount the two dates of Fleck until further information is available. As noted earlier and as described below, most of the rocks of the southern Arabian Shield have characteristics typical of those formed in the island-arc environment by subduction-related processes. We shall refer to the group of rocks in the western part of the southern Shield, which formed from 1100 to 800 m.y. ago, as the 'older ensimatic-arc complex' and those in the eastern and northwestern parts, which formed from 800 to 690 m.y. ago, as the 'younger marginal-arc compl

Open-File Report↗

USGS2019

Hydrogeologic framework of the Virginia Eastern Shore

The Yorktown-Eastover aquifer system of the Virginia Eastern Shore consists of upper, middle, and lower confined aquifers overlain by correspondingly named confining units and underlain by the Saint Marys confining unit. Miocene- to Pliocene-age marine-shelf sediments observed in 205 boreholes include medium- to coarse-grained sand and shells that compose the aquifers and fine-grained sand, silt, and clay that compose the confining units. The upper confining unit also includes fine-grained and organic-rich back-barrier and estuarine sediments of Pleistocene age. An overlying surficial aquifer is composed mostly of Pleistocene-age nearshore sand and gravel with smaller amounts of cobbles and boulders. In addition, Pleistocene-age sediments that fill three buried paleochannels are for the first time explicitly delineated here as distinct hydrogeologic units. Two aquifers are composed of medium- to coarse-grained fluvial sand and gravel, and an intervening confining unit is composed of fine-grained estuarine sand, silt, clay, and organic material. Aquifer and confining-unit sediments are also mixed with reworked marine-shelf sediments eroded from the sides of the paleochannels. Hydrogeologic units of the Yorktown-Eastover aquifer system generally dip eastward, are as much as several tens of feet thick, and have an undulating configuration possibly resulting from the underlying Chesapeake Bay impact crater. Aquifers and confining units are incised by the three paleochannels along an upward-widening and eastward-lengthening series of structural “windows.” Hydrogeologic units within mainstems and branching tributaries of the paleochannels dip southeastward parallel to slopes of the paleochannels, are as much as several tens of feet thick, and laterally abut the Yorktown-Eastover aquifer system along paleochannel sidewalls. The Yorktown-Eastover aquifer system is thereby hydraulically breached by the paleochannels to alternately create barriers to or conduits for groundwater flow. Results of previously documented aquifer tests at 58 wells indicate that transmissivity is generally greatest in young, shallow, and coarse-grained nearshore and fluvial sediments of the surficial aquifer and paleochannels. Transmissivity progressively decreases with depth in older, deeper, and finer grained marine-shelf sediments of the Yorktown-Eastover aquifer system, probably because they have undergone compaction as a result of greater overburden pressure over longer periods of time. Compiled chloride concentrations in samples from 330 wells generally increase downward, with most of the samples collected at altitudes above −300 feet and with most concentrations less than 250 milligrams per liter. The saltwater-transition zone has a broad trough-like shape aligned with the peninsula, being relatively shallow along the coastline and deeper along the central “spine.” Because movement of the saltwater is slow, the configuration largely reflects groundwater flow prior to widespread groundwater withdrawals. Fresh groundwater has leaked downward along deep parts of the saltwater-transition zone and leaked upward along shallower parts to discharge at the coast. The saltwater-transition zone also exhibits an anomalous ridge across the center of the peninsula. Groundwater levels indicate that the saltwater ridge formed primarily by the Exmore paleochannel acting as a large lateral collector drain. Groundwater levels were lowered, and the position of saltwater-transition zone was elevated, by a flow conduit that intercepted groundwater that otherwise would have flowed toward and discharged along the coastline. Nearly all freshwater on the Virginia Eastern Shore is supplied by groundwater withdrawals, which have lowered water levels, altered hydraulic gradients, and created a concern for saltwater intrusion. Previous characterizations of groundwater conditions that are relied on to manage groundwater development have been limited by a lack of hydrogeologic information, particularly data on buried paleochannels that are critical to safeguarding the groundwater supply. Using recently available expanded information, the U.S. Geological Survey undertook a study in cooperation with the Virginia Department of Environmental Quality during 2016–19 to develop an improved description of the groundwater system called a “hydrogeologic framework.” The hydrogeologic framework can aid water-supply planning and development by providing information on broad trends in aquifer configurations, hydraulic properties, and proximity to saltwater to avoid chloride contamination. Digital models to evaluate effects of groundwater withdrawals can also be improved with expanded data and capabilities to evaluate paleochannel hydraulic connections and the potential for saltwater movement. The hydrogeologic framework is limited by the nonuniform distribution of boreholes and the subjective delineation of aquifers and confining units, including those within paleochannels that are regarded as preliminary. The configuration of the saltwater-transition zone is also regarded as preliminary because of the nonuniform distribution of groundwater samples. Low well-sampling frequency precludes characterizing movement of the saltwater-transition zone. A monitoring strategy of sampling and possibly electromagnetic-induction well logging could be used to detect saltwater movement.

Virginia↗

USGS1983

Water quality of Lake Arlington on Village Creek, north-central Texas; 1973 to 1981

Water in Lake Arlington on Village Creek in north-central Texas had volume-weighted average concentrations of less than 240 milligrams per liter of dissolved solids, less than 30 milligrams per liter of dissolved chloride, and less than 40 milligrams per liter of dissolved sulfate between January 29, 1973, and August 20, 1981. The water was moderately hard (hardness greater than 60 but less than 120 milligrams per liter as calcium carbonate). The concentrations of each of these constituents were usually greatest during winter, especially during the first few years of the study, but decreased significantly as discharges of municipal wastes were systematically and progressively diverted to treatment facilities downstream from the reservoir. Thermal stratification in Lake Arlington usually begins during March or April and persists until October. Thermal stratification has resulted in significant seasonal and areal variations in the concentration of dissolved oxygen, dissolved iron, dissolved manganese, total inorganic nitrogen, and total phosphorus. Oxygen utilized in the decay of organic matter is not replenished during periods of summer stagnation, and water below depths of 30 to 40 feet usually contains less than 2 milligrams per liter of dissolved oxygen during stagnation. Even though heated effluent from an electrical generating plant is returned to the reservoir at site GC and causes an elevation of water temperature, average dissolved oxygen levels at this site are not significantly different from levels at other sites. During summer stagnation, reducing conditions result in the dissolution of iron and manganese from bottom deposits at deep sites in the reservoir. At site AQ, a deep site near Arlington Dam, dissolved iron concentrations in water near the bottom during summer stagnation ranged from less than 10 to 1,100 micrograms per liter and averaged about 640 micrograms per liter. Dissolved manganese concentrations near the bottom at site AC during summer staynation ranged from 20 to 2,700 micrograms per liter and averaged about 1,500 micrograms per liter. The concentrations of dissolved iron and dissolved manganese in water throughout the reservoir during winter circulation and in water near the reservoir surface during summer stagnation averaged less than 50 micrograms per liter. Seasonal temperature and dissolved oxygen cycles resulted in the recycling of dissolved iron and dissolved manganese between the water and bottom sediments. However, no significant accumulation of these constituents within the reservoir was detected during the study. The concentrations of total inorganic nitrogen and total phosphorus are greatest during summer stagnation in water near the bottom at deep sites. At site AC during the summer, the concentrations of total inorganic nitrogen in the hypolimnion averaged about 0.9 milligram per liter, and the concentration of total phosphorus near the bottom averaged about 0.2 milligram per liter. The concentrations of total inorganic nitrogen in the epilimnion at site AC averaged about 0.1 milligram per liter; the concentrations of total phosphorus averaged less than 0.1 milligram per liter. The densities and composition of algal populations varied seasonally. At site AC, total algae counts ranged from 200 to 240,000 cells per mi Hi liter and averaged about 50,000 cells per milliliter. At site FC, total algae counts ranged from 1,000 to 290,000 cells per milliliter and averaged about 56,000 cells per milliliter. Algal densities were greatest during the summer with blue-green algae being the predominant phyla.

Texas↗

USGS2007

Quaternarymagmatism in the Cascades - Geologic perspectives

Foreward The Cascade magmatic arc is a belt of Quaternary volcanoes that extends 1,250 km from Lassen Peak in northern California to Meager Mountain in Canada, above the subduction zone where the Juan de Fuca Plate plunges beneath the North American Plate. This Professional Paper presents a synthesis of the entire volcanic arc, addressing all 2,300 known Quaternary volcanoes, not just the 30 or so visually prominent peaks that comprise the volcanic skyline. Study of Cascade volcanoes goes back to the geological explorers of the late 19th century and the seminal investigations of Howel Williams in the 1920s and 1930s. However, major progress and application of modern scientific methods and instrumentation began only in the 1970s with the advent of systematic geological, geophysical, and geochemical studies of the entire arc. Initial stimulus from the USGS Geothermal Research Program was enhanced by the USGS Volcano Hazards Program following the 1980 eruption of Mount St. Helens. Together, these two USGS Programs have provided more than three decades of stable funding, staffing, and analytical support. This Professional Paper summarizes the resultant USGS data sets and integrates them with the parallel contributions of other investigators. The product is based upon an all-encompassing and definitive geological database, including chemical and isotopic analyses to characterize the rocks and geochronology to provide the critical time constraints. Until now, this massive amount of data has not been summarized, and a systematic and uniform interpretation firmly grounded in geological fact has been lacking. Herein lies the primary utility of this Cascade volume. It not only will be the mandatory starting point for new workers, but also will provide essential geological context to broaden the perspectives of current investigators of specific Cascade volcanoes. Wes Hildreth's insightful understanding of volcanic processes and his uncompromising scientific integrity make him uniquely qualified to present this synthesis. During more than three decades of volcanological studies, he has carried out comprehensive investigations of Mount Adams, Mount Baker, the Three Sisters, and the Simcoe Mountains Volcanic Field. He also brings a broad experience in other volcanic arcs, having conducted integrated field and laboratory investigations at several major volcanic centers in the Andes and the Aleutian arcs. His expertise and perspective have been further enhanced by in-depth petrologic studies of caldera environments, primarily in Long Valley, California, and Yellowstone. On the basis of all these field and laboratory investigations and exhaustive literature searches, he has published three definitive petrologic syntheses addressing the passage and transformation of basaltic magmas from their mantle sources through the crust to form the many types of volcanic manifestations at the Earth's surface. A major strength of this Professional Paper is that it adheres to data first and foremost, and only then correlates these data with relevant theories. Petrological and geophysical interpretation is left to the later sections of the volume, and even there is never allowed to stray from the pertinent databases. Hildreth's interpretations are not just idle speculations, but are carefully reasoned inferences firmly based on his thorough evaluation of the observational geological data. Professional Paper 1744 should not be skimmed lightly, in the hope that the salient points will quickly rub off. Instead, every section, indeed every paragraph, presents scholarly observations and insightful interpretations that demand careful and thoughtful study. This volume will influence and guide the course of Cascade investigations for decades to come.

British Columbia, California, Oregon, Washington↗

USGS2023

Hydrogeology of sand and gravel aquifers in the Owasco Inlet watershed, Cayuga and Tompkins Counties, New York

This study is a continuation of a series of hydrogeologic appraisals that have been conducted since 1980, as part of a cooperative, long-term, detailed aquifer mapping program by the U.S. Geological Survey and the New York State Department of Environmental Conservation. These appraisals provide a foundation for wellhead protection programs, water-resource management and planning decisions, and groundwater remediation in upstate New York. The Owasco Inlet watershed drains north directly to Owasco Lake, one of New York’s Finger Lakes. The watershed is similar in form to other watersheds of the Finger Lakes region of New York State and is characterized by broad, smooth uplands punctuated by the 18-mile-long Owasco Inlet valley and the secondary valleys of Decker, Dresserville, and Hemlock Creeks. All these streams occupy “through valleys”—the valleys are continuous into adjacent watersheds such that watershed divides are high points within the valley bottoms, rather than in uplands. Most glacial deposits in the watershed were deposited during the Valley Heads Readvance and subsequent retreat (with at least one minor readvance). Estimates are that the Valley Heads Readvance likely peaked in the Cayuga basin about 17,000 (calendar) years ago based on dates from western New York and the Mohawk Valley in east-central New York. It was the last major ice advance of the Pleistocene Epoch in this region. This readvance covered the entire Owasco watershed. Valley Heads ice in the Owasco watershed was part of the Cayuga ice lobe, which flowed parallel to the Owasco Inlet valley as far south as Moravia, but which became progressively more eastward south of Locke, effectively raking across the valley from the west. The Owasco Inlet watershed drains north, like other Finger Lakes watersheds, and during deglaciation, northward meltwater drainage was largely blocked by the ice, which resulted in development of a series of regional proglacial lakes in which fine lacustrine sediments predominated. Lacustrine sediments constitute much of the Owasco Inlet valley fill, but it has been pointed out that there are no obvious outlet channels exiting the Owasco Inlet watershed, and it has been proposed that there was northward drainage of meltwater into the ice within the larger, neighboring Cayuga Trough. The lacustrine deposits in the Owasco Inlet valley are commonly underlain by thinner coarse-grained stratified deposits (subaqueous fans and eskers) of variable sorting and permeability. An exception occurs at Groton, N.Y., where retreating ice paused long enough for coarse-grained sediments to fill much of the valley. Smaller, higher elevation valleys have a wider variety of glacial valley-fill deposits, ranging from fine lacustrine sediments to sand and gravel to till. Groundwater is the sole source of water supply in the area; glacial sand and gravel aquifers are the primary water source in the Owasco Inlet and Decker Creek valleys, and fractured bedrock aquifers typically supply domestic wells in the remaining valleys and upland areas. Municipal supplies tap a variety of aquifer types in the Owasco Inlet valley and nearby uplands. The hamlet of Locke taps the extensive confined aquifer beneath fine-grained lacustrine deposits in the valley. The Village of Moravia taps a semiconfined aquifer that overlies proglacial lake deposits and is partly confined by overlying recent lake deposits and alluvium. Withdrawals from this aquifer may also induce water from the Owasco Inlet into the aquifer. The Village of Groton draws from two aquifers: (1) a thin upland unconfined sand and gravel aquifer tapped by an infiltration gallery and (2) the local unconfined or semiconfined aquifer in the Owasco Inlet valley. Another aquifer with potential for municipal supply is the unconfined aquifer in the Decker Creek valley near Wilson Corners. The confined aquifer in the lower Dresserville Creek valley may have some water-resource potential, but it is largely untested. Unconfined aquifers are the most susceptible to contamination from activities at land surface directly above the aquifer because precipitation and subsequent recharge can transport contaminants directly to the water table. Adjacent upland areas can also contribute contaminants. Confined aquifers are less susceptible to contamination from overlying land surface areas because confining units largely prevent downward movement of water. Recharge occurs elsewhere at unconfined upvalley locations and along valley walls where alluvial fans, ice-contact deposits, or stream incision into the valley wall may provide pathways for downward movement of groundwater.

New York↗

USGS2024

Incorporating climate data into emergency planning and exercises: A primer for emergency management practioners and data developers

Climate change has and will continue to sharpen climate-related risks to communities and natural resources in California and elsewhere, as the probabilities of more extreme weather, floods, and fires continue to increase. This poses a problem of novel situations for emergency management. Progress has been made in terms of formally incorporating climate projections, data, and research on expected changes in climate-driven hazards into long-term hazard mitigation and climate adaptation strategies at both state and national levels. However, there are fewer examples of how climate change considerations have, or could be, incorporated into shorter-term emergency preparedness and response strategies. This is an important gap to fill, as climate resilience depends not only on mitigation and prevention measures, but also on the ability of agencies to coordinate and effectively minimize impacts when prevention measures fall short. The goal of this primer is to provide guidance on how to incorporate the best available information on climate variability and change into emergency management planning, with a focus on the development and use of extreme weather event scenarios for use in exercises. The first section is aimed toward a broad audience, including emergency management practitioners who use extreme weather event scenarios. It provides an overview of available data and tools that can inform scenario design as well as techniques for scenario design based on the hazard of interest, the audience and application, and the technical skills and resources required to develop, summarize, and/or visualize the data. This section concludes with an overview of approaches and lessons learned related to extreme event response planning and exercise design. Overall, this section highlights the advantages of developing quantitative scenarios based on spatial data, which allows visualizations and interactive data explorations that can provide greater specificity in discussions related to preparedness and response strategies. It further highlights the advantages of developing a core expert working group to guide planning, holding pre-exercise workshops to engage diverse communities outside of the emergency management sector, and engaging decisionmakers post-exercise to communicate key issues and outcomes as well as potential approaches for mitigating consequences that were identified by participants. The second section is aimed toward the scientific community and data developers involved in the creation of extreme weather event scenarios. This section provides technical guidance and detailed descriptions of four types of data resources and five analytical approaches that can be used to create extreme weather event scenarios based on the design considerations highlighted in section one. The computational resources and expertise required varies substantially across the options presented and is a primary consideration. These requirements, in addition to considerations related to audience and application, may determine the novelty and detail of the event, the detail of weather forecast information that can be provided, and the spatial extent across which the event can reasonably be modeled. The importance of, and approaches for, delivering information in a form that is accessible to emergency management practitioners is also discussed.

Report↗

USGS2011

Borehole geophysical investigation of a formerly used defense site, Machiasport, Maine, 2003-2006

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, collected borehole geophysical logs in 18 boreholes and interpreted the data along with logs from 19 additional boreholes as part of an ongoing, collaborative investigation at three environmental restoration sites in Machiasport, Maine. These sites, located on hilltops overlooking the seacoast, formerly were used for military defense. At each of the sites, chlorinated solvents, used as part of defense-site operations, have contaminated the fractured-rock aquifer. Borehole geophysical techniques and hydraulic methods were used to characterize bedrock lithology, fractures, and hydraulic properties. In addition, each geophysical method was evaluated for effectiveness for site characterization and for potential application for further aquifer characterization and (or) evaluation of remediation efforts. Results of borehole geophysical logging indicate the subsurface is highly fractured, metavolcanic, intrusive, metasedimentary bedrock. Selected geophysical logs were cross-plotted to assess correlations between rock properties. These plots included combinations of gamma, acoustic reflectivity, electromagnetic induction conductivity, normal resistivity, and single-point resistance. The combined use of acoustic televiewer (ATV) imaging and natural gamma logs proved to be effective for delineating rock types. Each of the rock units in the study area could be mapped in the boreholes, on the basis of the gamma and ATV reflectivity signatures. The gamma and mean ATV reflectivity data were used along with the other geophysical logs for an integrated interpretation, yielding a determination of quartz monzonite, rhyolite, metasedimentary units, or diabase/gabbro rock types. The interpretation of rock types on the basis of the geophysical logs compared well to drilling logs and geologic mapping. These results may be helpful for refining the geologic framework at depth. A stereoplot of all fractures intersecting the boreholes indicates numerous fractures, a high proportion of steeply dipping fractures, and considerable variation in fracture orientation. Low-dip-angle fractures associated with unloading and exfoliation are also present, especially at a depth of less than 100 feet below the top of casing. These sub-horizontal fractures help to connect the steeply dipping fractures, making this a highly connected fracture network. The high variability in the fracture orientations also increases the connectivity of the fracture network. A preliminary comparison of all fracture data from all the boreholes suggests fracturing decreases with depth. Because all the boreholes were not drilled to the same depth, however, there is a clear sampling bias. Hence, the deepest boreholes are analyzed separately for fracture density. For the deepest boreholes in the study, the intensity of fracturing does not decline significantly with depth. It is possible the fractures observed in these boreholes become progressively tighter or closed with depth, but this is difficult to verify with the borehole methods used in this investigation. The fact that there are more sealed fractures at depth (observed in optical televiewer logs in some of the boreholes) may indicate less opening of the sealed fractures, less water moving through the rock, and less weathering of the fracture infilling minerals. Although the fracture orientation remained fairly constant with depth, differences in the fracture patterns for the three restoration sites indicate the orientation of fractures varies across the study area. The fractures in boreholes on Miller Mountain predominantly strike northwest-southeast, and to a lesser degree they strike northeast. The fractures on or near the summit of Howard Mountain strike predominantly east-west and dip north and south, and the fractures near the Transmitter Site strike northeast-southwest and dip northwest and southeast. The fracture populations for the boreholes on or near the summit of Howard Mountain show more variation than at the other two sites. This variation may be related to the proximity of the fault, which is northeast of the summit of Howard Mountain. In a side-by-side comparison of stereoplots from selected boreholes, there was no clear correspondence between fracture orientation and proximity to the fault. There is, however, a difference in the total populations of fractures for the boreholes on or near the summit of Howard Mountain and the boreholes near the Transmitter Site. Further to the southwest and further away from the fault, the fractures at the Transmitter Site predominantly strike northeast-southwest and northwest-southeast.Heat-pulse flowmeter (HPFM) logging was used to identify transmissive fractures and to estimate the hydraulic properties along the boreholes. Ambient downflow was measured in 13 boreholes and ambient upflow was measured in 9 boreholes. In nine other bedrock boreholes, the HPFM did not detect measurable vertical flow. The observed direction of vertical flow in the boreholes generally was consistent with the conceptual flow model of downward movement in recharge locations and upward flow in discharge locations or at breaks in the slope of land surface. Under low-rate pumping or injection rates [0.25 to 1 gallon per minute (gal/min)], one to three inflow zones were identified in each borehole. Two limitations of HPFM methods are (1) the HPFM can only identify zones within 1.5 to 2 orders of magnitude of the most transmissive zone in each borehole, and (2) the HPFM cannot detect flow rates less than 0.010 + or - 0.005 gal/min, which corresponds to a transmissivity of about 1 foot squared per day (ft2/d). Consequently, the HPFM is considered an effective tool for identifying the most transmissive fractures in a borehole, down to its detection level. Transmissivities below that cut-off must be measured with another method, such as packer testing or fluid-replacement logging. Where sufficient water-level and flowmeter data were available, HPFM results were numerically modeled. For each borehole model, the fracture location and measured flow rates were specified, and the head and transmissivity of each fracture zone were adjusted until a model fit was achieved with the interpreted ambient and stressed flow profiles. The transmissivities calculated by this method are similar to the results of an open-hole slug test; with the added information from the flowmeter, however, the head and transmissivity of discrete zones also can be determined. The discrete-interval transmissivities ranged from 0.16 to 330 ft2/d. The flowmeter-derived open-hole transmissivity, which is the combined total of each of the transmissive zones, ranged from 1 to 511 ft2/d. The whole-well open-hole transmissivity values determined with HPFM methods were compared to the results of open-hole hydraulic tests. Despite the fact that the flowmeter-derived transmissivities consistently were lower than the estimates derived from open-hole hydraulic tests alone, the correlation was very strong (with a coefficient of determination, R2, of 0.9866), indicating the HPFM method provides a reasonable estimate of transmissivities for the most transmissive fractures in the borehole. Geologic framework, fracture characterization, and estimates of hydraulic properties were interpreted together to characterize the fracture network. The data and interpretation presented in this report should provide information useful for site investigators as the conceptual site groundwater flow model is refined. Collectively, the results and the conceptual site model are important for evaluating remediation options and planning or implementing the design of a well field and borehole completions that will be adequate for monitoring flow, remediation efforts, groundwater levels, and (or) water quality. Similar kinds of borehole geophysical logging (specifically the borehole imaging, gamma, fluid logs, and HPFM) should be conducted in any newly installed boreholes and integrated with interpretations of any nearby boreholes. If boreholes are installed close to existing or other new boreholes, cross-hole flowmeter surveys may be appropriate and may help characterize the aquifer properties and connections between the boreholes.

Maine↗

USGS1971

Availability of streamflow for recharge of the basal aquifer in the Pearl Harbor area, Hawaii

The Pearl Harbor area is underlain by an extensive basal aquifer that contains large supplies of fresh water. Because of the presence of a cap rock composed of sedimentary material that is less permeable than the basaltic lava of the basal aquifer, seaward movement of ground water is retarded. The cap rock causes the basal water to stand at a high level; thus, the lens of fresh water that floats on sea water is thick. Discharge from the basal ground-water body, which includes pumpage from wells and shafts, averaged 250 million gallons per day during 1931-65. Because the water level in the basal aquifer did not decline progressively, recharge to the ground-water body must have been approximately equal to discharge. Although pumping for agricultural use has decreased since 1931, net ground-water discharge has increased because of a large increase in pumping for urban use. Substitution of ground water for surface water in the irrigation of sugarcane has also contributed to a net increase in ground-water discharge. The development of Mililani Town will further increase discharge. The increase in ground-water discharge may cause an increase in chloride content of the water pumped from wells near the shore of Pearl Harbor unless the increased discharge is balanced by increased recharge to the local aquifer. The aquifer is recharged by direct infiltration and deep percolation of rain, principally in the high forested area, by infiltration and percolation of irrigation water applied in excess of plant requirements, by seepage of water through streambeds, and possibly by ground-water inflow from outside the area. Recharge is greatest in the uplands, where rainfall is heavy and where much infiltration takes place before rainwater collects in the middle and lower reaches of stream channels. Once water collects in and saturates the alluvium of stream channels, additional inflow to the streams will flow out to sea, only slightly decreased by seepage. Average annual direct runoff from the 90-square-mile Pearl Harbor area is 47.27 million gallons per day, or 11.1 inches; this is 13.3 percent of the average annual rainfall (83.3 in.) over the area. Average annual direct runoff in streams at the 800- and 400-foot altitudes is 29 and 38 million gallons per day, respectively. Kipapa Stream has the largest average annual direct runoff at those altitudes--6 and 9 million gallons per day, respectively. Because streams are flashy and have a wide range in discharge, only 60 percent of the average annual runoff can be economically diverted through ditches to recharge areas. The diversion may be increased slightly if reservoirs are used in conjunction with ditches to temporarily detain flows in excess of ditch capacity. The planned irrigation use of some of the perennial flow available in Waikele Stream near sea level will decrease pumping from and increase recharge to the basal aquifer. Suspended-sediment load is mainly silt and clay, and it increases rapidly with increased discharge. Thus, the use of streamflow for artificial recharge poses problems. High flows must be used if recharge is to be effective, but flows must not be so high as to cause clogging of recharge facilities with sediment or woodland debris. Practical tests are needed to determine the advantages and disadvantages of different types of recharge structures, such as a reservoir or basin, large-diameter deep shafts, deep wells, or combinations of all these structures.

Water Supply Paper↗

USGS1972

Regional and other general factors bearing on evaluation of earthquake and other geologic hazards to coastal communities of southeastern Alaska

The great Alaska earthquake of March 27, 1964, brought into sharp focus the need for engineering geologic studies in seismically active regions. As a result, nine communities in southeastern Alaska were selected for reconnaissance investigations as an integral part of an overall program to evaluate earthquake and other geologic hazards in most of the larger Alaska coastal communities. This report gives background information on the regional and other general factors that bear on these evaluations. Southeastern Alaska, about 525 miles long and averaging about 125 miles in width, consists of a narrow mainland strip and numerous islands. For the most part, it is a region of rugged relief with numerous glaciers capping many of the higher mountainous areas and with long linear fiords forming the inland waterways. A maritime climate prevails with mild winters and cool summers. The southeastern part of the region receives the highest precipitation in the continental United States. Ketchikan, with a population of 6,994 in 1970, is the largest city. Geology and structure of the area are complex. Igneous, metamorphic, and sedimentary rocks crop out and range in age from Paleozoic to Tertiary. Surficial deposits of Pleistocene and Holocene age mantle many areas. All of southeastern Alaska, except probably the highest peaks, was covered by glacier ice advances of late Pleistocene age. Major deglaciation was well advanced by 10,000 years ago--a time which approximately marks the end of the Pleistocene and the beginning of the Holocene. There followed a period of warm climate called the Hypsithermal, which in southeastern Alaska began 7,000-8,000 years ago and ended about 4,800-3,500 years ago. Glaciers in most places receded back of their present positions. The Hypsithermal was followed by an interval (termed Neoglaciation) of cooler climate and resurgence of glacier ice which continues to the present, although most glaciers are now rapidly receding. During the past 10,000 years worldwide sea level has risen about 100 feet, but during the past 4,000 years it has risen only about 10 feet or about 0.03 inch per year. With sea level used as a datum, the amount of sea-level rise must be added to the apparent uplift of land for the time under consideration to determine the actual amount of land uplift. The widespread presence of emergent marine deposits, several hundred feet above sea level, demonstrates that the land in southeastern Alaska has been uplifted since the last major deglaciation. The greatest known has been uplifted since the last major deglaciation. The greatest known uplift is in the vicinity of Juneau where glaciomarine deposits are present 750 feet above present sea level. Part of southeastern Alaska is presently undergoing one of the most rapid rates of uplift of any place in the world. The fastest emergence is occurring in the Glacier Bay area where the land is being uplifted relative to sea level approximately 3.9 cm per year. Most or all of the uplift appears to be due to rebound as a result of deglaciation. Southeastern Alaska lies within the circum-Pacific earthquake belt, one of the world's greatest zones of seismic activity. During historic time, there have been five earthquakes in the region with magnitudes of 8 or greater, three with magnitudes of 7 to 8, eight with magnitudes of 6 to 7, more than 15 with magnitudes of 5 to 6, and about 140 recorded earthquakes with magnitudes smaller than 5 or of unassigned magnitudes. All of the earthquakes with magnitudes 8 or greater, and a large proportion of the others, appear to be related to the active Fairweather- Queen Charlotte Islands fault system or its western extension, the Chugach-St. Elias fault. Earthquake epicenters on the Denali fault system, the other major fault system in southeastern Alaska, are few in comparison. However, because high microearthquake activity has been recorded recently on this system and earthquakes of moderate size have occurred on some of its segments, the Denali fault system probably should not be dismissed as a relict fault system of no current tectonic importance. There are numerous other known faults, as well as lineaments that may be faults of varying degrees of tectonic activity in southeastern Alaska, adjacent Canada, and eastern Alaska. One of these elements is the Totschunda fault system, which connects with the Denali fault system in eastern Alaska; it has been very active during Holocene time but few historical earthquake epicenters appear to be related to it. Both historical seismicity and geologic conditions, such as frequency and recency of faulting, must be considered together to permit an assessment of the future earthquake probability of an area. Data are too few for both factors for an accurate evaluation to be made of earthquake probability in southeastern Alaska. However, information compiled in the form of strain-release and seismic-zone maps permit some generalizations. Thus, it is tentatively concluded that most, if not all, of southeastern Alaska should be placed in seismic zone 3, a zone in which earthquakes of magnitude greater than 6 will occur from time to time and where there may be major damage to manmade structures. Inferred effects from future earthquakes in southeastern Alaska include: (1) surface displacement along faults and other tectonic land-level changes, (2) ground shaking, (3) compaction, (4) liquefaction in cohesionless materials, (5) reaction of sensitive and quick clays, (6) water-sediment ejection and associated subsidence and ground fracturing, (7) earthquake-induced sub aerial slides and slumps, (8) earthquake induced subaqueous slides, (9) effects on glaciers and related features, (10) effects on ground water and stream flow, and (11) tsunamis, seiches, and other abnormal water waves. Because of the reconnaissance nature of our studies in the coastal communities and the sparsity of laboratory data on physical properties of geologic units in each area studied, the inferred effects must be largely empirical and generalized. Therefore, the inferences are based in large part upon the effects of past major earthquakes in Alaska and elsewhere, particularly upon the well-documented effects of the Alaska earthquake of March 27, 1964. Buildings, highways, bridges, tunnels, harbor facilities, pipelines, canals, and other manmade structures may be severely damaged or destroyed by fault displacement or related tectonic land-level changes in southeastern Alaska. Direct damage from fault rupture would be restricted virtually to structures built directly athwart the fault. In California and Nevada, fault rupture almost always accompanies shocks of magnitude 6.5 or greater. The Alaska earthquake of March 27, 1964, and the Chilean earthquake of May 22, 1960, dramatically illustrated the severe adverse effects that can result from uplift or subsidence over a wide area. The variable most responsible for the degree of shaking at any epicentral distance is the type of ground. Generally, shaking is considerably greater in poorly consolidated deposits than in hard bedrock, particularly if the deposits are water saturated. Severe shaking of alluvial deposits and manmade fill, with resultant heavy damage, is well documented from the records of many past earthquakes. Damage commonly has been heavy as a result of ground settlement caused by compaction of loose sediments by shaking during an earthquake. This has been especially true where compaction was accompanied by tectonic downdrop of land, such as occurred during the Chilean earthquake of 1960 and the Alaska earthquake of 1964. Loosely emplaced manmade fill, deltaic deposits, beach deposits, and alluvial deposits may be susceptible to compaction in southeastern Alaska during a severe earthquake. Liquefaction of sand and silt is a fairly common effect of large earthquakes. It was well illustrated at Niigata, Japan, during the earthquake of June 16, 1964, and resulted in extensive damage. When part of a sloping soil mass liquefies, the entire mass can undergo catastrophic failure and can flow as a high-density liquid. In southeastern Alaska, deltaic deposits probably would be most susceptible to liquefaction. Sensitive and quick clays, which lose a considerable part of their strength when shaken, commonly fail during an earthquake and become rapid earthflows. Extensive studies were made of the sensitivity of the Bootlegger Cove Clay at Anchorage because of the marked loss of shear strength and dramatic failures of the deposits during the Alaska earthquake of 1964. If similar sensitive clays are present in some places in southeastern Alaska, they most likely are in some of the emergent fine-grained marine deposits; supporting data to confirm their presence, however, are largely lacking. Records of some 50 major earthquakes show that in at least half of the instances water and sediment have been ejected from surficial deposits Water-sediment ejection and associated subsidence and ground fracturing commonly cause extensive damage to the works of man. Ejecta may fill basements and other low-lying parts of buildings. Agricultural land can be covered with a blanket of infertile soils, and small ponds can be filled or made shallow. In southeastern Alaska these phenomena are most likely to occur on valley floors, deltas, tidal flats, alluvial fans, swamps, and lakeshores. Earthquake-induced sliding on land generally is confined to steep slopes but may take place in fine-grained deposits on moderately to nearly flat surfaces if the deposits are subject to liquefaction. A large rockslide triggered by the Lituya Bay, Alaska, earthquake of July 10, 1958, generated a wave that surged up the opposite wall of the inlet to a record height of 1,740 feet. During the Hebgen Lake, Montana, earthquake of August 17, 1959, a spectacular rockslide plunged into the Madison River canyon, buried 28 people, dammed the river, and created a large lake. Earthquake-records are replete with accounts of sliding of surficial deposits during moderate to large earthquakes. Most or all of the general factors that favor subaerial landsliding are present in southeastern Alaska. Earthquake-induced subaqueous slides can produce adverse effects both nearshore and some distance offshore. Nearshore sliding may progress shoreward and destroy harbor facilities and other structures, commonly with substantial loss of life. Disastrous large submarine slides occurred along the fronts of deltas in Seward and Valdez during the Alaska earthquake of 1964. In similar fashion, the largest submarine slides in southeastern Alaska likely will be triggered along the larger delta fronts. Sliding farther offshore can constitute a threat to navigation because of changes in water depths. Also underwater sliding can break communication cables. Glaciers were not greatly affected by the Alaska earthquake of 1964 despite the fact that about 20 percent of the area that underwent strong shaking is covered by ice. In contrast, the cataclysmic avalanche of ice and rock that fell from a high glacier-covered peak in Peru during the earthquake of May 31, 1970, produced devastating effects downvalley on man and his works in the form of mudflows. Most towns in southeastern Alaska are sufficiently distant from glaciers so as not be to directly affected. Both the Alaska earthquake of 1964 and the Hebgen Lake, Montana, earthquake of 1959 significantly affected ground- and surface-water regimens. Water levels in some wells declined whereas in others flow increased. Some springs discharged at a rate three times as much as normal; flow of others decreased or stopped. Discharge of many streams increased markedly. Most or all of the effects described above could occur in parts of southeastern Alaska during future large earthquakes. Tsunamis, seiches, and other abnormal water waves associated with large earthquakes commonly cause vast property damage and heavy loss of life. Tsunami effects can be devastating to coastal areas as far as many thousands of miles from their generation source. Seiche effects generally are confined to inland bodies of water or to relatively enclosed coastal bodies of water. Abnormal waves generated by submarine sliding or by subaerial sliding into water generally produce only local effects but may be highly devastating. Tsunami waves resulting from the Chilean earthquake of 1960 inflicted extensive damage and loss of life on coastal communities throughout a large part of southern Chile, and significant runups and damage were recorded in many places throughout the Pacific Ocean area. The tsunami waves generated by the Alaska earthquake of 1964 struck with devastating force along a broad stretch of the Alaska coast and produced heavy property damage and loss of life as far away as Crescent City, Calif. Seiche waves generated by that earthquake reached runup heights of 20-30 feet on some lakes in Alaska, and water-level fluctuations were recorded on streams, reservoirs, lakes, and swimming pools in States bordering the Gulf of Mexico. Waves generated by submarine sliding struck violently at a number of places during or immediately after the quake and were the major cause of loss of life and damage to property. Slide-generated waves probably would have a higher destructive potential in southeastern Alaska than either tsunami waves or seiche waves because of their possibly higher local runups and because they can hit the shores almost without warning during or immediately after an earthquake. Nonearthquake-related geologic hazards, although generally far less dramatic than those related to earthquakes, tend to occur so much more frequently or persistently that their aggregate effects can be significant. Three kinds of geologic hazards of this type are discussed: (1) nonearthquake-induced landsliding and subaqueous sliding, (2) flooding, and (3) land uplift. The potential for nonearthquake-triggered landsliding in southeastern Alaska ranges widely from place to place. Past sliding generally furnishes the clue in the prediction of where and in what materials future sliding will occur. Fast-moving rockslides, debris slides, and mudflows can be expected to occur from time to time on steep slopes and be highly destructive to highways, power plants, pipelines, buildings, and other facilities located on a slope or at its base. Present slow downslope movement of talus can be expected to continue at the same general rate unless conditions are changed by man or there are climatic changes. Snow and debris avalanches can be especially hazardous during winter months. Long-inactive landslides may be triggered into renewed activity or new slides may be created by man-induced modifications. Accelerated slope erosion and debris flows may follow large-scale clearing and cutting of timber. Subaqueous sliding can be expected to occur periodically along fronts of deltas and on other oversteepened underwater slopes. Floods have been common in parts of southeastern Alaska because of heavy precipitation and rapid runoff from steep slopes with resulting heavy damage to roads and other facilities. Continued damage can be expected in the future unless more remedial measures are taken. Current uplift of land in southeastern Alaska, although probably not affecting man significantly in a short period of time, may have some adverse long-term effects. These long-term effects should be borne in mind when facilities such as docks and boat harbors are constructed on or near the shore, where there is a critical relation between height of land and water.

Alaska↗

USGS1972

Appraisal of iron deposits in southern and western Turkey

Between May 20 and June 17, 1969, previously known iron deposits were examined widely at eight separate localities in western Turkey. The object of the examinations was to learn the, nature, geologic setting, and approximate size of each deposit, to review prior estimates of size, and possibly recommend additional exploratory work.. The full extent of each deposit is poorly known at the present time, so recommended additional work entails drilling, digging trenches or pits, geologic mapping or, combinations of these activities. On Qaldagi Mountain an area of about 1 sq km is capped by bredciated chert under which may be a continuous zone of mixed iron oxides and chert fragments. The thickness of the ferruginous zone is poorly known but is as much as 12 meters, in at least one place. The- ferruginous material and chert appear to have formed by the weathering of serpentine, bun this concept needs further testing. Drilling is recommended to determine the grade, thickness, and extent-of the ferruginous zone beneath the cherty cap. Inasmuch as mining by hand sorting is in progress, part of the deposit can be considered to be marginally in the category of iron reserves. The Keceborlu iron deposit consists of earthy to slightly compacted hematite and limonite mixed with small chert fragments. The surface area underlain by ferruginous rock is about 5,000 to 7,500 sq meters. The maximum known thickness of the deposit is about 7 meters. Iron appears to have been concentrated by weathering and oxidation of cherty limestone. The deposit is probably either a remnant of a once more extensive weathered cap, or a sink hole filling. The Keceborlu area warrants a low priority for further exploration, but one drill hole is recommended to test the thickness of the deposit. The iron deposits at Mellec are layered and vein-magnetite replacements of limestone. The six known deposits are discontinuous. No additional. work is recommended. ' The Gilindire Iron deposit consists of irregular concentrations of pisolitic and earthy hematite and 'limonite along an unconformity or disconformity between two groups of limestone. The ferruginous zone is incompletely known around the rim of the large Gilindire syncline. Data from trenches 5 to 6 km around the syncline--about ? the possible length of the ferruginous zone--provide the main knowledge about the size and grade of ferruginous lenses. The ferruginous lenses range in thickness from a fraction of a meter, to about 3 meters, but appear to average 1 meter or less, and range in grade from about 10 to 37 percent iron. No additional exploration work is recommended at Gilindire. The Buyukeceli deposit consists of veinlike masses of earthy and compact hematite and limonite cutting fresh limestone. The veins apparently originally contained siderite which has been weathered and converted to iron oxide. Further exploration by drilling is recommended at such time as other largest deposits are able to be brought into the development stage in the Mediterranean coastal area of Turkey. The iron deposits overlooking Bayas on the Gulf of Iskenderun ere in one or more layers along the west-facing front of the Amanus Mountain Range, between beds of gently to moderately east-dipping limestone. Isolated exposures may represent a once-continuous ferruginous bed that has been blockfaulted and intruded by serpentine. The ferruginous bed (or beds) is 20-30 meters thick, and consists of a mixture of very fine grained hematite and claylike material. Iron content ranges from 20 to 40 percent and aluminum, averages about 15 percent. Available data on distribution are scant but suggest that one ferruginous bed may be 1-2 kilometers long, 500 meters wide and 20 meters thick. The potentially large size of the Payas deposits warrants an early coordinated program of drilling end beneficiation testing. An iron deposit was examined on a conspicuous limestone ridge in the Syrian graben east of the Amanus Moun

Open-File Report↗

USGS2008

Understanding contaminants associated with mineral deposits

Interdisciplinary studies by the U.S. Geological Survey (USGS) have resulted in substantial progress in understanding the processes that control the release of metals and acidic water from inactive mines and mineralized areas, the transport of metals and acidic water to streams, and the fate and effect of metals and acidity on downstream ecosystems. The potential environmental effects associated with abandoned and inactive mines, resulting from the complex interaction of a variety of chemical and physical processes, is an area of study that is important to the USGS Mineral Resources Program. Understanding the processes contributing to the environmental effects of abandoned and inactive mines is also of interest to a wide range of stakeholders, including both those responsible for managing lands with historically mined areas and those responsible for anticipating environmental consequences of future mining operations. The recently completed (2007) USGS project entitled 'Process Studies of Contaminants Associated with Mineral Deposits' focused on abandoned and inactive mines and mineralized areas in the Rocky Mountains of Montana, Colorado, New Mexico, Utah, and Arizona, where there are thousands of abandoned mines. Results from these studies provide new information that advances our understanding of the physical and biogeochemical processes causing the mobilization, transport, reaction, and fate of potentially toxic elements (including aluminum, arsenic, cadmium, copper, iron, lead, and zinc) in mineralized near-surface systems and their effects on aquatic and riparian habitat. These interdisciplinary studies provide the basis for scientific decisionmaking and remedial action by local, State, and Federal agencies charged with minimizing the effects of potentially toxic elements on the environment. Current (2007) USGS research highlights the need to understand (1) the geologic sources of metals and acidity and the geochemical reactions that release them from their sources, (2) the pathways that facilitate transport from those sources, and (3) the processes that control the fate of the elements once released from the sources. Experts in the fields of economic geology, structural geology, mineralogy, geophysics, geochemistry, hydrology, ground-water modeling, microbiology, and toxicology came together for a series of studies that address these relationships on scales ranging from the microscopic to the watershed. This Circular presents results and highlights from the detailed, interdisciplinary studies that include investigations in both mining-affected areas and mineralized but unmined areas. The first section of the Circular describes laboratory and site-scale field investigations that primarily focus on mineralogic and biologic controls on the source and release of metals and acidity from mine-waste rock and hydrothermally altered areas. The second section describes a set of basin- to watershed-scale studies that not only investigate the source and release of metals and acidity but also the transport of these constituents away from the source areas. The third section is a summary of results from postremediation ecosystem monitoring. For more information on these and other project-related studies, please visit the project Web site at http://minerals.cr.usgs.gov/projects/contaminants/index.html. The Web site includes a complete bibliography and detailed descriptions of each interdisciplinary study.

Circular↗

USGS1994

Analysis of data from test-well sites along the downdip limit of freshwater in the Edwards Aquifer, San Antonio, Texas, 1985-87

Many researchers have studied the downdip limit of freshwater in the Edwards aquifer or various aspects of the saline-water zone and its relation to the freshwater zone. These studies were summarized and used to synthesize a consistent hydrologic and geochemical framework from which to interpret data from field studies. The concept derived from the previous work on the downdip limit of the freshwater zone is that fresh recharge water entered the aquifer and developed a vast flow system controlled by barrier faults. Some recharge water flows into the saline-water zone rather than toward major freshwater discharge points. The water that enters the salinewater zone continues to dissolve gypsum and dolomite, and calcite precipitates out of the water. This process of dedolomitization has helped to develop the large secondary porosity of the freshwater zone as the downdip limit of the freshwater zone progressively moved downdip in recent geologic time. The drilling of test holes and installation of monitoring wells began in 1985 and helped to define the downdip limit of the freshwater zone at one location. Dolomite was found in greater amounts in rocks from the saline-water-zone test hole than in rocks from the freshwater-zone test hole. Other mineralogic and lithologic contrasts between the saline-water-zone test hole and the freshwater-zone test hole support the conceptual model of dedolomitization. Geophysical logs and test-hole survey logs helped to define the stratification of freshwater and associated altered rock textures, secondary porosity development, and water chemistry in the freshwater-, saline-water-, and transition-zone test holes. The differences in actual measured head among the seven completed monitor wells varied over time, especially during periods of substantial water use. The water levels in two monitor wells completed at the freshwater zone (site D; wells Dl and D2) responded quickly and strongly to withdrawals. In the transition zone (site C; wells Cl and C2), the water level in the shallow monitor well (Cl) completed in a cavern responded quickly, but because it was farther from the water-supply wells near site D, it did not respond as strongly to changes in withdrawals at the nearby well field. The water levels in the three salinewater wells at site A (Al, A2, and A3) and the deep site C well (C2) were less responsive to stresses relative to the water-level changes in the freshwater wells (Dl, D2, and Cl). Large amounts of freshwater were produced from the upper 300 to 350 feet of the aquifer in the freshwater zone (site D). Water produced from below this interval was as saline as that from the saline-water zone (site A). The cavern near the top of the aquifer in the transition zone (site C) produced large amounts of freshwater. The freshwater produced from the cavern was of a different geochemical type than the water from the other wells. The saline-water-zone test hole (site A) produced small amounts of water having specific conductance generally about 5,800 to 6,200 microsiemens per centimeter at 25 degrees Celsius. A consistent trend in the water quality was not detected in the monitor-well data for July 1986-April 1987. This was caused, in part, by the average to above-average rainfall and by the lack of large withdrawals during the period. The water quality of samples from several of the wells was similar to the water quality determined by a previous study of the area. Geochemistry of the oil- or gas-well brines from downdip in the saline-water zone had slight resemblance to the geochemistry of the water at the downdip limit of freshwater; updip flow of saline water toward the freshwater zone was not indicated.

Texas↗

USGS2012

Nutrient and suspended-sediment trends, loads, and yields and development of an indicator of streamwater quality at nontidal sites in the Chesapeake Bay watershed, 1985-2010

The U.S. Geological Survey (USGS) updates information on loads of, and trends in, nutrients and sediment annually to help the Chesapeake Bay Program (CBP) investigators assess progress toward improving water-quality conditions in the Chesapeake Bay and its watershed. CBP scientists and managers have worked since 1983 to improve water quality in the bay. In 2010, the U.S. Environmental Protection Agency (USEPA) established a Total Maximum Daily Load (TMDL) for the Chesapeake Bay. The TMDL specifies nutrient and sediment load allocations that need to be achieved in the watershed to improve dissolved oxygen, water-clarity, and chlorophyll conditions in the bay. The USEPA, USGS, and state and local jurisdictions in the watershed operate a CBP nontidal water-quality monitoring network and associated database that are used to update load and trend information to help assess progress toward reducing nutrient and sediment inputs to the bay. Data collected from the CBP nontidal network were used to estimate loads and trends for two time periods: a long-term period (1985-2010) at 31 "primary" sites (with storm sampling) and a 10-year period (2001-10) at 33 primary sites and 16 "secondary" sites (without storm sampling). In addition, loads at 64 primary sites were estimated for the period 2006 to 2010. Results indicate improving flow-adjusted trends for nitrogen and phosphorus for 1985 to 2010 at most of the sites in the network. For nitrogen, 21 of the 31 sites showed downward (improving) trends, whereas 2 sites showed upward (degrading) trends, and 8 sites showed no trends. The results for phosphorus were similar: 22 sites showed improving trends, 4 sites showed degrading trends, and 5 sites indicated no trends. For sediment, no trend was found at 40 percent of the sites, with 10 sites showing improving trends and 8 sites showing degrading trends. The USGS, working with CBP partners, developed a new water-quality indicator that combines the results of the 10-year trend analysis with results from a greater number of sites (64 primary sites) where loads and yields of total nitrogen and phosphorus and sediment could be calculated. The new indicator shows fewer significant trends for the 10-year time period than for the long-term time period (1985-2010). For 2001-10, total nitrogen trends were downward (improving) at 14 sites and upward (degrading) at 2 sites; no trend was found at 17 sites. For total phosphorus, 12 sites showed improving trends, 4 sites showed degrading trends, and 17 sites showed no trend. For total sediment, most sites (21) did not exhibit a significant trend; 3 sites showed improving trends, and 10 sites showed degrading trends. Few significant trends were seen at the 16 secondary sites: improving trends for total nitrogen at 4 sites, improving trends for total phosphorus at 2 sites, and a degrading trend for sediment at 1 site. Total streamflow to the Chesapeake Bay was 20 percent higher in 2010 than in 2009 and is considered to be within the normal range of flow, whereas annual streamflow at 28 sites was greater in 2010 than in 2009. No trends in daily streamflow were detected at the 31 long-term sites. Combined loads for the farthest downstream nontidal monitoring sites (called "River Input Monitoring sites") increased 33 percent for total nitrogen, 120 percent for total phosphorus, and 330 percent for total sediment from 2009 to 2010. The large increase in phosphorus and sediment loads in 2010 was caused in large part by two large storm events that occurred during the spring in the Potomac River Basin. Yields (load per watershed area) of total nitrogen in the Chesapeake Bay watershed decreased from north to south (New York to Virginia). No spatial patterns were discernible for total phosphorus or sediment.

Delaware, Maryland, New York, Pennsylvania, Virgin↗

USGS1986

Observations of the eruptions of July 22 and August 7, 1980, at Mount St. Helens, Washington

The explosive eruptions of July 22 and August 7, 1980, at Mount St. Helens, Wash., both included multiple eruptive pulses. The beginnings of three of the pulses-two on July 22 and one on August 7-were witnessed and photographed. Each of these three began with a fountain of gases and pyroclasts that collapsed around the vent and generated a pyroclastic density flow. Significant vertical-eruption columns developed only after the density flows were generated. This behavior is attributable to either an increase in the gas content of the eruption jet or a decrease in vent radius with time. An increase in the gas content may have occurred as the vent was cleared (by expulsion of a plug of pyroclasts) or as the eruption began to tap deeper, gas-rich magma after first expelling the upper, gas-depleted part of the magma body. An effective decrease of the vent radius with time may have occurred as the eruption originated from progressively deeper levels in the vent. All of these processes-vent clearing; tapping of deeper, gas-rich magma; and effective decrease in vent radius-probably operated to some extent. A 'relief-valve' mechanism is proposed here to account for the occurrence of multiple eruptive pulses. This mechanism requires that the conduit above the magma body be filled with a bed of pyroclasts, and that the vesiculation rate in the magma body be inadequate to sustain continuous eruption. During a repose interval, vesiculation of the magma body would cause gas to flow upward through the bed of pyroclasts. If the rate at which the magma produced gas exceeded the rate at which gas escaped to the atmosphere, the vertical pressure difference across the bed of pyroclastic debris would increase, as would the gas-flow rate. Eventually a gas-flow rate would be achieved that would suddenly diminish the ability of the bed to maintain a pressure difference between the magma body and the atmosphere. The bed of pyroclasts would then be expelled (that is, the relief valve would open) and an eruption would commence. During the eruption, gas would be lost faster than it could be replaced by vesiculation, so the gas-flow rate in the conduit would decrease. Eventually the gas-flow rate would decrease to a value that would be inadequate to expel pyroclasts, so the conduit would again become choked with pyroclasts (that is, the relief valve would close). Another period of repose would commence. The eruption/repose sequence would be repeated until gas-production rates were inadequate to reopen the valve, either because the depth of the pyroclast bed had become too great, the volatile content of the magma had become too low, or the magma had been expended. A timed sequence of photographs of a pyroclastic density flow on August 7 indicates that, in general, the velocity of the flow front was determined by the underlying topography. Observations and details of the velocity/topography relationship suggest that both pyroclastic flows and pyroclastic surges formed. The following mechanism is consistent with the data. During initial fountain collapse and when the flow passed over steep, irregular terrain, a highly inflated suspension of gases and pyroclasts formed. In this suspension, the pyroclasts underwent rapid differential settling according to size and density; a relatively low-concentration, fine-grained upper phase formed over a relatively high-concentration coarse-grained phase. The low-particle-concentration phase (the pyroclastic surge) was subject to lower internal friction than the basal high-concentration phase (the pyroclastic flow), and so accelerated away from it. The surge advanced until it had deposited so much of its solid fraction that its net density became less than that of the ambient air. At this point it rose convectively off the ground, quickly decelerated, and was overtaken by the pyroclastic flow. The behavior of the flow of August 7 suggests that a pyroclastic density flow probably expands through the ingestion of ai

Professional Paper↗

USGS2010

Biosecurity Plan for Palmyra Atoll

This Biosecurity Plan for Palmyra Atoll was developed for The Nature Conservancy (TNC) Palmyra Program to refine and expand goals and objectives developed through the Conservation Action Plan process. The Biosecurity Plan is one in a series of adaptive management plans designed to achieve TNC's mission toward the protection and enhancement of native wildlife and habitat. The Biosecurity Plan focuses on ecosystem security, and specifically identifies and addresses issues related to non-native and potentially invasive species. The Plan attempts to identify pathways of invasion and strategies for preventing or reducing new introductions. Overall, the Biosecurity Plan provides a framework to implement and track the progress of conservation and restoration goals related to non-native species on Palmyra Atoll. Palmyra Atoll is one of the Northern Line Islands in the Pacific Ocean southwest of the Hawai`ian Islands. It consists of many heavily vegetated islets arranged in a horseshoe pattern around four lagoons and surrounded by a coral reef. At present, Palmyra Atoll harbors various non-native or invasive species in the terrestrial and marine ecosystems. The most notable examples of terrestrial invasive species include coconut trees (Cocos nucifera) and black rats (Rattus rattus). Although it is unclear whether they are non-native, coconut trees are currently the most dominant plant across Palmyra Atoll. They compete with native plant species for space and resources, and are potentially detrimental to seabirds dependent on native vegetation. Black rats are known to predate ground-nesting seabirds and are likely responsible for the lack of burrowing seabird reproduction on Palmyra Atoll. The most notable example of a marine invasive species is the corallimorph (Rhodactis howsei). Although Rhodactis howsei is a native species, it can take advantage of human-altered habitat and significantly change the natural habitat by aggressively outcompeting native corals. Although the extent and impacts of these and other non-native and (or) invasive species are not fully understood, they are clearly a threat to the native species and overall ecosystem integrity of Palmyra Atoll. In fact, non-native invasive species have been considered the most important threat to ecosystems in Hawai`i and the second most important threat to biodiversity world-wide. Palmyra Atoll is somewhat protected because of its remote location, but there are still potential pathways for the introduction of non-native and possibly invasive species. With the continued influx of aircraft and ocean vessels and their contents to and around Palmyra Atoll, we anticipate many more concerns related to the import and spread of non-native invasive species in the future. In terms of ecosystem security, prevention is the most effective and efficient tool for managing invasive species. There are various potential pathways for introduction and spread of non-native species within Palmyra Atoll's terrestrial and marine ecosystems. Identification of these pathways provides a first step in preventing introductions. We also recommend establishing, enhancing, and enforcing quarantine protocols to prevent future non-native species invasions. Other critical steps to minimize the impacts and spread of invasive species include early detection through inventory and monitoring, as well as containment, control, and management of non-native species already established at Palmyra Atoll. These efforts in combination with research and education will serve to inform management decisions related to ecosystem integrity. Along with reinstating ecosystem security, this Biosecurity Plan aims to evaluate new risk factors related to non-native and potentially invasive species. To that end, an adaptive management process of audit and review is highly recommended to ensure the implementation and efficacy of the management practices outlined above. In addition, it will be important to identify high r

Open-File Report↗

USGS1997

Historical land-use changes and potential effects on stream disturbance in the Ozark Plateaus, Missouri

Land-use changes have been blamed for creating disturbance in the morphology of streams in the Ozark Plateaus, Missouri (hereafter referred to as the "Ozarks"). Historical evidence and stratigraphic observations document that streams have been aggraded by substantial quantities of gravel beginning sometime at or near the time of European settlement of the Ozarks. Before European settlement, streams were depositing a mixed sediment load of gravel bedload and silty overbank sediment. Observations of early explorers conspicuously lack descriptions of extensive gravel bars; observations of geologists working during the middle to late 1800's before significant landuse disturbance, however, include descriptions of large quantities of gravel in stream banks and beds. The first change in land cover as settlement progressed from the early 1800's to approximately 1880 was replacement of valley-bottom forest with cultivated fields and pastures. At the same time, suppression of wildfires in the uplands caused an increase of woodland with woody understory at the expense of grassland and oak savannah. Valley-bottom clearing probably initiated some direct disturbance of stream channels, but fire suppression would have decreased runoff and sediment yield from uplands. Beginning sometime from 1870 to 1880 and continuing until 1920, commercial timber companies began large operations in the Ozarks to harvest shortleaf pine for sawlogs and oak for railroad ties. Selective cutting of large timber, use of livestock for skidding logs from the forest, and avoidance of the steeper slopes minimized the effect of this phase of logging on runoff and sediment supply of uplands and valley-side slopes. Continued decreases in the erosional resistance of valley bottoms through clearing and road building and the incidence of extreme regional floods from 1895 to 1915 probably caused initiation of moderate stream disturbance. This hypothesis is supported by historical and oral-historical observations that stream instability began before the peak of upland destabilization from 1920 to 1960. The post-Timber-boom period (1920-60) included the institution of annual burning of uplands and cut-over valley-side slopes, increased grazing on open range, and increased use of marginal land for cultivated crops. Models for landuse controls on annual runoff, storm runoff, and soil erosion indicate that this period should have been the most effective in creating stream disturbance. Written historical sources and oral-historical accounts indicate that erosion was notable mainly on lands in row-crop cultivation. Oral-history respondents consistently recall that smaller streams had more discharge for longer periods from 1920 to 1960 than from 1960 to 1993; many additionally observed that floods are "flashier" under present-day (1993) conditions. Changes in the timing of hydrographs probably relate to changes in upland and riparian zone vegetation that decreased storage and flow resistance. Probably the most destabilizing effect on Ozarks stream channels during this period was caused by livestock on the open range that concentrated in valley bottoms and destroyed riparian vegetation in the channels and on banks. Destruction of riparian vegetation in small valleys may have encouraged headward migration of channels, resulting in extension of the drainage network and accelerated release of gravel from storage in the small valleys. This hypothesis is supported by lack of other sources for the large quantity of gravel in Ozarks streams and oral-historical observations that gravel came out of the runs, rather than from slopes. From 1960 to 1993, cultivated fields and total improved land in farms decreased, but cattle populations continued to increase. This increase in grazing density has the potential to maintain runoff and sediment delivery to streams at rates higher than natural background rates. Whereas some riparian zones have been allowed to grow up into bottom-land forest, this stabilizing effect occurs on only a small part of valley-bottom land. Recovery processes aided by riparian vegetation are limited by channel instability and frequent, large floods.

Water Supply Paper↗

USGS1994

Historical land-use changes and potential effects on stream disturbance in the Ozark Plateaus, Missouri

Land-use changes have been blamed for creating disturbance in the morphology of streams in the Ozark Plateaus, Missouri (hereafter referred to as the Ozarks). Historical evidence and stratigraphic observations document that streams have been aggraded by substantial quantities of gravel beginning sometime at or near the time of European settlement of the Ozarks. Before European settlement, streams were depositing a mixed sediment load of gravel bedload and silty over-bank sediment. Observations of early explorers conspicuously lack descriptions of extensive gravel bars; observations of geologists working during the middle to late 1800's before significant land-use disturbance, however, include descriptions of large quantities of gravel in stream banks and beds. The first change in land cover as settlement progressed from the early 1800's to approximately 1880 was replacement of valley-bottom forest with cultivated fields and pastures. At the same time, suppression of wildfires in the uplands caused an increase of woodland with woody understory at the expense of grassland and oak savannah. Valley-bottom clearing probably initiated some direct disturbance of stream channels, but fire suppression would have decreased runoff and sediment yield from uplands. Beginning sometime during 1870 to 1880 and continuing until 1920, commercial timber companies began large operations in the Ozarks harvesting shortleaf pine for sawlogs and oak for railroad ties. Selective cutting of large timber, use of livestock for skidding logs from the forest, and avoidance of the steeper slopes minimized the effect of this phase of logging on runoff and sediment supply of uplands and valley-side slopes. Continued decreases in the erosional resistance of valley bottoms through clearing and road building, and the incidence of extreme regional floods from 1895 to 1915, probably caused initiation of moderate stream disturbance. This hypothesis is supported by historical and oral-historical observations that stream instability began before the peak of upland destabilization from 1920 to 1960. The post-Timber-boom period (1920 to 1960) included the institution of annual burning of uplands and cut-over valley-side slopes, increased grazing on open range, and increased use of marginal land for cultivated crops. Models for land-use controls on annual runoff, storm runoff, and soil erosion indicate this period should have been the most effective in creating stream disturbance. Written historical sources and oral-historical accounts indicate that erosion was notable mainly on lands in row-crop cultivation. Oral-history respondents consistently recall that smaller streams had more discharge for longer periods during 1920 to 1960 than during 1960 to 1993; many additionally observed that floods are "flashier" under present-day (1993) conditions. Changes in the timing of hydrographs probably relate to changes in upland and riparian zone vegetation that decreased storage and flow resistance. Probably the most destabilizing effect on Ozarks stream channels during this period was caused by livestock on the open range that concentrated in valley bottoms and destroyed riparian vegetation in the channels and on banks. Destruction of riparian vegetation in small valleys may have encouraged headward migration of channels, resulting in extension of the drainage network and accelerated release of gravel from storage in the small valleys. This hypothesis is supported by lack of other sources for the large quantity of gravel in Ozarks streams and oral-historical observations that gravel came out of the runs, rather than from slopes. From 1960 to 1993, cultivated fields and total improved land in farms decreased, but cattle populations continued to increase. This increase in grazing density has the potential to maintain runoff and sediment delivery to streams at rates higher than natural background rates. Whereas some riparian zones have been allowed to grow up into bottom-land forest, this stabilizing effect occurs on only a small part of valley-bottom land. Recovery processes aided by riparian vegetation are limited by channel instability and frequent, large floods.

Missouri↗