Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Acoustics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83Linked to original sources
USGS2003

The effect of chamber mixing velocity on bias in measurement of sediment oxygen demand rates in the Tualatin River basin, Oregon

Three sediment oxygen demand (SOD) measurement chambers were deployed in the Tualatin River near Tigard, Oregon, at river mile 10 in August 2000. SOD rates were calculated for three different circulation velocities during each chamber deployment. The SOD rate at each velocity was calculated from a graph of dissolved oxygen concentration versus elapsed time. An acoustic doppler current profiler (ADCP) was used to measure stream discharge and near-bottom water velocities in the Tualatin at river mile 10 and at two upstream locations. Measured river and chamber velocities were similar, indicating that results from the chambers were representative of instream effects. At low to moderate chamber circulation velocities (less than about 7.5 centimeters per second), the measured SOD rate appeared to be only slightly affected by the circulation velocity, indicating that the measured rates reflect the rate of oxygen utilization by chemical and biological reactions in the sediment rather than the rate of physical transport of oxygen to the sediment-water interface. Above about 7.5 centimeters per second, however, the measured oxygen depletion rate was affected by the circulation velocity, as sufficient energy was generated within the chamber to resuspend bottom sediment, as evidenced by increased turbidity. The resuspended sediment particles contributed to the measured oxygen loss rate by increasing the surface area of decomposing material in contact with the water column, resulting in a measured SOD rate that was anomalously high. Two different alignments of the chamber circulation diffusers were tested. With both diffuser alignments, SOD rates were similar at circulation velocities low enough to avoid sediment resuspension. The same resuspension effect probably exists in the Tualatin River during storm-runoff events following prolonged periods of low flow, when increased stream velocity may result in the resuspension of bottom sediments. The resuspension causes increased turbidity and increased oxygen demand, resulting in lower instream dissolved oxygen concentrations.

Water-Resources Investigations Report↗
USGS2005

Borehole-geophysical and hydraulic investigation of the fractured-rock aquifer near the University of Connecticut Landfill, Storrs, Connecticut, 2000 to 2001

An integrated borehole-geophysical and hydraulic investigation was conducted at the former landfill area near the University of Connecticut in Storrs, Connecticut, where solvents and landfill leachate have contaminated a fractured-bedrock aquifer. Borehole-geophysical techniques and hydraulic methods were used to characterize the site bedrock lithology and structure, fractures, and hydraulic properties. The geophysical and hydraulic methods included conventional logs, borehole imaging, borehole radar, flowmeter under ambient- and stressed hydraulic conditions, and discrete-zone hydraulic testing, sampling, and monitoring. The conventional geophysical-logging methods included caliper, deviation, electromagnetic induction, gamma, specific conductance, and fluid temperature. The advanced methods included optical and acoustic imaging of the borehole wall, heat-pulse flowmeter, and directional radar reflection. Borehole-geophysical methods were used to further define conductive features identified with surface-geophysical methods in the first phase of the investigation. The results of the surface- and borehole-geophysical logging were evaluated in an iterative and integrated manner to develop a conceptual model of ground-water flow at the site. The rock type, foliation, and fractures at the site were characterized from high-resolution optical televiewer (OTV) images of rocks penetrated by the boreholes and were compared to drilling logs and conventional geophysical logs. The rocks are interpreted as fine- to mediumgrained quartz-feldspar-biotite-garnet gneiss and schist with local intrusions of quartz diorite and pegmatite and minor concentrations of sulfide mineralization similar to rocks described as the Bigelow Brook Formation on regional geologic maps. Layers containing high concentrations of sulfide minerals appear as high electrical conductivity zones on electromagnetic-induction and borehole-radar logs. Foliation in the rocks generally strikes to the southwest and northeast, and dips to the northwest and southeast consistent with previous investigations in this area. The orientation of foliation, however, varies locally and with depth in some of the boreholes. These results are consistent with geologic mapping that has identified small-scale folding. The orientations of the transmissive fractures identified in the six boreholes logged for this investigation are similar to the fracture orientations mapped in a previous investigation. Many of these fractures are oriented with a north-northwest strike and have a shallow dip to the west. Other transmissive fractures have a southwest strike and dip at shallow angles to the northwest, and some strike roughly east-west and dip to the north and south. Flowmeter logging was used to identify transmissive fractures and to estimate the hydraulic properties in the boreholes. Ambient down flow was measured in one borehole, and ambient up flow and down flow were measured in another borehole. The other four bedrock boreholes did not have measurable vertical flow. Under low-rate pumping conditions (0.25 to 0.5 gallons per minute), one to three inflow zones were identified in each well. Commonly, fractures that are active under ambient conditions contribute to the well under pumping conditions. The ambient conditions were incorporated into the determination of the relative proportions of transmissivity. Specific capacity and transmissivity were determined for these open-hole low-rate pumping tests. Quasi-steady-state water levels were reached in four of the boreholes, including MW201R, MW204R, MW302R, and W202-NE. When pumped at low-rate conditions for 0.5 to 4 hours, the specific capacity ranged from 0.03 to 0.18 gallons per minute per foot. The open-hole transmissivity estimates ranged from 4.9 to 30 feet squared per day (ft2/d). Open-hole transmissivity was determined for boreholes that did not reach quasi-steady-state conditions under low-rate pumping conditions. Transmissivity was estimated for MW201R, MW202R, and MW203R using non-equilibrium methods, pumping rate, and the transient drawdown data to estimate the open-hole transmissivity. Transmissivity in these boreholes ranged from 0.98 to 3.2 ft 2 /d. The transmissivity and head of individual fractures or zones of fractures were estimated from heat-pulse flowmeter data acquired under ambient and stressed conditions. In the absence of ambient flow, data from two profiles of heat-pulse flowmeter data under two different stressed conditions were used to estimate the transmissivity and head of individual fracture zones. Only two boreholes, MW302R and W202-NE, had sufficient data for these analyses. The estimated transmissivity of individual transmissive zones ranged from 1.2 to 9.2 ft 2 /d. The transmissivity values determined by this numerical simulation method were less than the open-hole estimations, which were 15 and 30 ft 2 /d. Transmissivity also was measured directly over discrete intervals of the borehole using a straddle-packer apparatus and constant-rate pumping tests. Pumping rates were less than or equal to 0.25 gallons per minute. These discretezone single-hole pumping tests were conducted over a short period of time, usually about 30 minutes to 1 hour in duration. Pumping continued until the test zone reached a steady-state water level or until it was determined that the zone could not yield water at the pumped rate. The estimated transmissivity of individual transmissive zones ranged from about 0.21 to 11 ft 2 /d. The zone at a depth of 197 feet in W202-NE was the only zone that had discrete-interval testing with a straddle packer and sufficient heat-pulse flowmeter data for modeling the flow and estimating transmissivity and head. The two methods produced similar results. The straddle-packer method estimated a transmissivity of 4.7 ft 2 /d, and the heat-pulse flowmeter modeling results estimated a transmissivity of 6.9 ft 2 /d. A comparison of the transmissivity estimates indicate estimates typically are within an order of magnitude. The heat-pulse flowmeter methods used in this investigation to determine transmissivity of the boreholes and the individual fractures measure only the upper two or three orders of magnitude of transmissivity. Hence, other fractures in these boreholes permit the movement of water; their transmissivities, however, are lower than the detection limits of the methods that were used for this investigation and very small compared to the transmissive fractures that were studied. The data collected in this investigation were used to design discrete-zone monitoring systems for four of the boreholes used for monitoring. The results of the investigation are useful for refining the conceptual site model of ground-water flow, and for providing critical information for interpreting the results of water-quality sampling.

Connecticut↗
USGS1976

Geohydrology of the Albin and La Grange areas, aoutheastern Wyoming

The Albin and La Grange areas in southeastern Wyoming are two adjoining different hydrologic areas. Since ground water is the only source of water for irrigation in the Albin area, 34 irrigation wells have been drilled since 1968 and developed in conjunction mostly with center-pivot sprinkler systems that in 1974 irrigated about 6,980 acres. Most irrigation wells are developed in channel deposits of the Ogallala Formation of late Miocene. Water levels in parts of these channel deposits have declined about 4 to 7 feet since pumping began in 1968. In the La Grange area, lands are irrigated by surface water, ground water or a combination of both. The best producing wells are those completed in both the Brule Formation of Oligocene age and the alluvium. Secondary porosity was located and elevated in the Brule using caliper logs, an Acoustic Borehole Televiewer and geophysical logs. From the spring of 1970 to the spring of 1974, hydrographs of wells in parts of the La Grange area show water-level rises of about 5 feet resulting from the net effect of surface-water recharge and groundwater pumpage. Throughout the La Grange area no significant annual water-table declines have occurred. It is unlikely that irrigation wells pumping near Horse Creek have caused significant direct streamflow depletion.

Wyoming↗
USGS1976

High-resolution seismic reflection profiling for mapping shallow aquifers in Lee County, Florida

High-resolution continuous seismic reflection profiling equipment was utilized to define the configuration of sedimentary layers underlying part of Lee County, Florida. About 45 miles (72 kilometers) of profile were made on the Caloosahatchee River Estuary and San Carlos Bay. Two different acoustic energy sources, a high resolution boomer and a 45-electrode high resolution sparker, both having a power input of 300 joules, were used to obtain both adequate penetration and good resolution. The seismic profiles show that much of the strata of middle Miocene to Holocene age apparently are extensively folded but not faulted. Initial interpretations indicate that: (1) the top of the Hawthorn Formation (which contains the upper Hawthorn aquifer) has much relief due chiefly to apparent folding; (2) the limestone, sandstone, and unconsolidated sand and phosphorite, which together compose the sandstone aquifer, appear to be discontinuous; (3) the green clay unit of the Tamiami Formation contains large scale angular beds dipping eastward; and (4) numerous deeply cut alluvium-filled paleochannels underlie the Caloosahatchee River. (Woodard-USGS)

Florida↗
USGS1985

Development and testing of highway storm-sewer flow measurement and recording system

A comprehensive study and development of measuring instruments and techniques for measuring all components of flow in a storm-sewer drainage system was undertaken by the U.S. Geological Survey under the sponsorship of the Federal Highway Administration. The study involved laboratory and field calibration and testing of measuring flumes, pipe insert meters, weirs, electromagnetic velocity meters as well as the development and calibration of pneumatic-bubbler pressure transducer head measuring systems. Tracer-dilution and acoustic flow meter measurements were used in field verification tests. A single micrologger was used to record data from all the above instruments as well as from a tipping-bucket rain gage and also to activate on command the electromagnetic velocity meter and tracer-dilution systems. (Author 's abstract)

Water-Resources Investigations Report↗
USGS1988

Well construction, lithology, and geophysical logs for boreholes in Bear Creek Valley near Oak Ridge, Tennessee

Twenty-four wells were constructed at nine sites at Bear Creek Valley to provide geologic and hydrologic information. Lithologic samples and suits of geophysical logs were obtained from the deepest boreholes at six of the sites. Two of these boreholes at the base of Chestnut Ridge were completed in the Maynardville Limestone and two were completed in the Nolichucky Shale. Two boreholes along Pine Ridge were completed in the Rome Formation. Zones of similar lithology within a borehole were delineated from rock cutting refined by examination of geophysical logs. The contact between the Maynardville Limestone and Nolichucky Shale was identified in two of the boreholes. Fractures and cavities were readily identifiable on the acoustic-televiewer and caliper logs. Distinct water-bearing intervals were also identified from the temperature, fluid resistance, and resistivity logs. Depths at which the drilling encounterd a thrust were identified in two boreholes in the Rome Formation from both rock cutting and geophysical logs.

Tennessee↗
USGS1990

A method to estimate canal leakage to the Biscayne Aquifer, Dade County, Florida

The leakage characteristics of channels that partially penetrate the Biscayne aquifer and have reduced bed permeability were studied. Leakage characteristics were described in terms of a reach transmissivity-defined as the volume flow rate out of the channel per unit length of the channel per unit drawdown, where drawdown is defined as the difference in altitude between the water surface in the canal and the water table in the adjacent aquifer. A theoretical expression was developed to relate the reach transmissivity to the transmissivity of the formation, mean channel width, distance of drawdown measurement from the channel centerline, ratio of drawdowns on both sides of the channel, and local reach transmissivity associated with reduced bed permeability. This theoretical expression was verified using a fine-scale numerical model, which gave accurate results when drawdowns were measured beyond 10 aquifer depths from the side of the channel. Using the theoretical formulation, it is shown that the reach transmissivity employed in regional ground-water models, which are based on average drawdowns within a cell, depends on the size of the cell as well as the transmissivity of the formation, channel width, and local reach transmissivity due to reduced bed permeability. The theoretical reach transmissivity function was compared with field measurements at L-31N Canal and Snapper Creek Extension Canal in Dade County, Florida. Analyses of the data for both canals showed good agreement between the estimated and measured reach transmissivities. At L- 31N Canal, field measurements indicated that the local reach transmissivity was relatively uniform over a 2-mile reach of the channel (averaging 630 cubic feet per second per mile per foot), and the formation transmissivity was 1.8 x106 feet squared per day. At Snapper Creek Extension Canal, an approximate analysis was necessary due to the inability of the acoustic velocity meter to measure very low water velocities in the channel. Assuming an aquifer transmissivity of 1 x 106 feet squared per day, drawdown measurements indicated that the local reach transmissivity was about 400 cubic feet per second per mile per foot. The theoretical relation, combined with the local reach transmissivity and formation transmissivity, was sufficient to predict the leakage out of L-31N Canal and Snapper Creek Extension Canal for any drawdown scenario.

Florida↗
USGS1994

Geohydrology and ground-water quality in the vicinity of a ground-water-contamination site in Rockford, Illinois

A geohydrologic investigation was performed by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to determine the distribution of volatile organic compounds in a fractured-rock aquifer near the Southeast Rockford Groundwater Contamination Site in Rockford, Ill. The geologic units of concern are the St. Peter Sandstone and Glenwood Formation; the dolomites of the Platteville and Galena Groups of Ordovician age; and the sands, gravels, silts, and clays of Quaternary age. The hydraulic units of concern are the unconsolidated aquifer, composed of sand and gravel; the fractured- dolomite aquifer, composed of the Galena and Platteville Groups and the dolomitic sections of the Glenwood Formation; and the sandstone aquifer, composed of the St. Peter Sandstone and the sandstone beds in the Glenwood Formation. The dolomite aquifer is well connected hydraulically to the overlying unconsolidated aquifer and the underlying sandstone aquifer. Caliper and acoustic-televiewer logs show several subhorizontal fractures in the dolomite that can be correlated throughout the study area. Comparison of televiewer and flowmeter logs indicates that most of the flow in the dolomite aquifer is through these fractures. Ground-water flow through two of the fractures can be correlated over large parts of the study area. Volatile organic compounds, in concentrations exceeding 2,000 micrograms per liter, were detected within the entire thickness of the dolomite aquifer where flow is measurable. Volatile organic compounds were detected in an area of the aquifer where they were thought to be absent in previous investigations.

Illinois↗
USGS1995

Geohydrology and water quality of the Durham Center Area, Durham, Connecticut

Contaminated ground water is widespread and persistent beneath the Durham Center area in the town of Durham, Conn. Most of the contaminants are organic halides, usually trichloroethene, 1,1,1-trichloroethane, and tetrachloroethene. Less extensive chemical contamination of surface water, soil, and glacial sediments also has been detected. Two manufacturing companies, located at the northern and southern ends of this largely residential area, are believed to be the principal sources of the organic compounds detected in ground water. The contamination of water in the bedrock, the primary source of drinking water throughout the area, is the major environmental concern. Maximum concentrations of trichloroethene in three bed- rock wells range from 4,500 to about 5,500 mg/L (micrograms per liter). Concentrations of trichloroethene greater than 5 mg/L, the maximum contaminant level established for drinking water by the U.S Environmental Protection Agency, have regularly been detected in water samples from many other bedrock wells for at least 9 years. The geohydrology of the area is highly complex. Compact lodgment till that is up to 30 feet thick and probably fractured, overlies the bedrock. The bedrock is lithologically heterogeneous, and con- sists mostly of red fluvial sandstone, siltstone, and conglomerate; it is locally interbedded with black lacustrine shales and gray sandstones. Lithology and stratigraphy interpreted from borehole-geophysical logs at Durham Center are consistent with the Portland Formation subfacies described in earlier geologic studies. Beds strike nearly north-south and dip gently eastward. At least one high-angle normal fault transects the bedrock; it strikes northeast and dips northwest. Acoustic televiewer logs, measurements at out-crops, and azimuthal, square-array, resistivity data indicate a dominance of northeast-striking fractures that dip steeply northwest and southeast. Less prevalent strike directions are north to east-north-east. The till and sedimentary bedrock are dual-porosity, dual-permeability media. The hydraulic conductivity of the bulk mass of till is believed to be on the order of tenths of a foot per day to about 2.5 feet per day, with a total porosity of about 25 percent and an estimated average fracture porosity of less than 1 percent. The reported transmissivities of the bedrock range from less than 1 to about 17,000 feet squared per day and storativity is generally about 10-4, but the accuracy of these values is uncertain. The intergranular porosity of the sandstone units is estimated to average 5 percent, and estimates of fracture porosity from square-array, resistivity soundings at two sites were 1.1 and 2.7 percent. The bedrock has characteristics of both a single aquifer and a multi-unit, artesian or leaky aquifer system. A local ground-water-flow system that includes the upper part of the bedrock is unconfined. A large- scale flow system in deeper parts of the bedrock has transported organic compounds across topographic drainage divides. Borehole-geophysical logs and head measurements indicate that the natural ground- water-flow system in the bedrock has been altered by drilled wells that connect fractures and by with- drawals from wells. A conceptual model of the movement and fate of organic contaminants suggests that (1) nonaqueous phase organic halides are retained near their source; (2) flow is primarily through fractures in the till and through fractures and bedding-plane openings in the sedimentary rocks; (3) retardation of contaminants occurs primarily by diffusion from fractures into the aquifer matrix; and (4) transport directions of dissolved organic halides are controlled by a combination of natural hydraulic gradients, hydraulic gradients produced by the cyclical pumping of wells, and by the strike directions of bedrock faults, fractures, and bedding planes.

Connecticut↗
USGS1997

An optimized network for phosphorus load monitoring for Lake Okeechobee, Florida

Phosphorus load data were evaluated for Lake Okeechobee, Florida, for water years 1982 through 1991. Standard errors for load estimates were computed from available phosphorus concentration and daily discharge data. Components of error were associated with uncertainty in concentration and discharge data and were calculated for existing conditions and for 6 alternative load-monitoring scenarios for each of 48 distinct inflows. Benefit-cost ratios were computed for each alternative monitoring scenario at each site by dividing estimated reductions in load uncertainty by the 5-year average costs of each scenario in 1992 dollars. Absolute and marginal benefit-cost ratios were compared in an iterative optimization scheme to determine the most cost-effective combination of discharge and concentration monitoring scenarios for the lake. If the current (1992) discharge-monitoring network around the lake is maintained, the water-quality sampling at each inflow site twice each year is continued, and the nature of loading remains the same, the standard error of computed mean-annual load is estimated at about 98 metric tons per year compared to an absolute loading rate (inflows and outflows) of 530 metric tons per year. This produces a relative uncertainty of nearly 20 percent. The standard error in load can be reduced to about 20 metric tons per year (4 percent) by adopting an optimized set of monitoring alternatives at a cost of an additional $200,000 per year. The final optimized network prescribes changes to improve both concentration and discharge monitoring. These changes include the addition of intensive sampling with automatic samplers at 11 sites, the initiation of event-based sampling by observers at another 5 sites, the continuation of periodic sampling 12 times per year at 1 site, the installation of acoustic velocity meters to improve discharge gaging at 9 sites, and the improvement of a discharge rating at 1 site.

Florida↗
USGS1997

Geohydrology and simulations of ground-water flow at Verona well field, Battle Creek, Michigan, 1988

Public water supply for the city of Battle Creek, Mich. is withdrawn from the Marshall Sandstone through wells at the Verona well field. Analysis of borehole acoustic televiewer, gamma, and single-point-resistance logs from wells in Bailey Park, near the well field, indicates 12 fracture zones in the Marshall Sandstone. Further interpretation of flow-meter and temperature logs from the same wells indicates that the fracture zones are locally interconnected but appear to remain isolated over a lateral distance of 3,000 feet. Organic chemicals were detected in water samples collected from water-supply wells in the Verona well field in 1981. In 1985, six water-supply wells were converted to purge wells to intercept organic chemicals and divert them from the remaining water-supply wells. Removal of these wells from service resulted in a water-supply shortage. A proposal in which an alternative purge system could be installed so that wells that are out of service may be reactivated was examined. A ground-water-flow model developed for this study indicates that, under the current purge configuration, most water from contaminant-source areas either is captured by purge wells or flows to the Battle Creek River. Some water, however, is captured by three water-supply wells. Model simulations indicate that with the addition of eight purge wells, the well field would be protected from contamination, most water from the contaminant-source areas would be captured by the purge system, and only a small portion would flow to the Battle Creek River. In an effort to augment the city's water supply, the potential for expansion of the Verona well field to the northeast also was investigated. Because of the addition of three municipal wells northeast of the well field, some water from the site of a gasoline spill may be captured by two water-supply wells. Ground water in the area northeast of Verona well field contains significantly lower concentrations of iron, manganese, and calcium carbonate than does water in the existing well field area. However, the Marshall Sandstone in this area has significantly lower transmissivities than those within Verona well field.

Michigan↗
USGS1998

Determining discharge-coefficient ratings for selected coastal control structures in Broward and Palm Beach counties, Florida

Discharges through 10 selected coastal control structures in Broward and Palm Beach Counties, Florida, are presently computed using the theoretical discharge-coefficient ratings developed from scale modeling, theoretical discharge coefficients, and some field calibrations whose accuracies for specific sites are unknown. To achieve more accurate discharge-coefficient ratings for the coastal control structures, field discharge measurements were taken with an Acoustic Doppler Current Profiler at the coastal control structures under a variety of flow conditions. These measurements were used to determine computed discharge-coefficient ratings for the coastal control structures under different flow regimes: submerged orifice flow, submerged weir flow, free orifice flow, and free weir flow. Theoretical and computed discharge-coefficient ratings for submerged orifice and weir flows were determined at seven coastal control structures, and discharge ratings for free orifice and weir flows were determined at three coastal control structures. The difference between the theoretical and computed discharge-coefficient ratings varied from structure to structure. The theoretical and computed discharge coefficient ratings for submerged orifice flow were within 10 percent at four of seven coastal control structures; however, differences greater than 20 percent were found at two of the seven structures. The theoretical and computed discharge-coefficient ratings for submerged weir flow were within 10 percent at three of seven coastal control structures; however, differences greater than 20 percent were found at four of the seven coastal control structures. The difference between theoretical and computed discharge-coefficient ratings for free orifice and free weir flows ranged from 5 to 32 percent. Some differences between the theoretical and computed discharge-coefficient ratings could be better defined with more data collected over a greater distribution of measuring conditions.

Florida↗
USGS1998

Results of borehole geophysical logging and hydraulic tests conducted in Area D supply wells, former U.S. Naval Air Warfare Center, Warminster, Pennsylvania

Borehole geophysical logging, aquifer tests, and aquifer-isolation (packer) tests were conducted in four supply wells at the former U.S. Naval Air Warfare Center (NAWC) in Warminster, PA, to identify the depth and yield of water-bearing zones, occurrence of borehole flow, and effect of pumping on nearby wells. The study was conducted as part of an ongoing evaluation of ground-water contamination at the NAWC. Caliper, natural-gamma, single-point resistance, fluid resistivity, and fluid temperature logs and borehole television surveys were run in the supply wells, which range in depth from 242 to 560 ft (feet). Acoustic borehole televiewer and borehole deviation logs were run in two of the wells. The direction and rate of borehole-fluid movement under non-pumping conditions were measured with a high-resolution heatpulse flowmeter. The logs were used to locate water-bearing fractures, determine probable zones of vertical borehole-fluid movement, and determine the depth to set packers. An aquifer test was conducted in each well to determine open-hole specific capacity and the effect of pumping the open borehole on water levels in nearby wells. Specific capacities ranged from 0.21 to 1.7 (gal/min)/ft (gallons per minute per foot) of drawdown. Aquifer-isolation tests were conducted in each well to determine depth-discrete specific capacities and to determine the effect of pumping an individual fracture or fracture zone on water levels in nearby wells. Specific capacities of individual fractures and fracture zones ranged from 0 to 2.3 (gal/min)/ft. Most fractures identified as water-producing or water-receiving zones by borehole geophysical methods produced water when isolated and pumped. All hydrologically active fractures below 250 ft below land surface were identified as water-receiving zones and produced little water when isolated and pumped. In the two wells greater then 540 ft deep, downward borehole flow to the deep water-receiving fractures is caused by a large difference in head (as much as greater then 49 ft) between water-bearing fractured in the upper and lower part of the borehole. Vertical distribution of specific capacity between land surface and 250 ft below land surface is not related to depth.

Water-Resources Investigations Report↗
USGS2001

Salt-front movement in the Hudson River estuary, New York — Simulations by one-dimensional flow and solute-transport models

The Hudson River is being considered for use as a supplemental source of water supply for New York City during droughts. One proposal entails withdrawal of Hudson River water from locations near Newburgh, Chelsea, or Kingston, but the extent to which this could cause the salt front to advance upstream to points where it could adversely affect community water supplies is unknown. The U.S. Geological Survey (USGS) one-dimensional Branch-Network Dynamic Flow model (BRANCH) was used in conjunction with the USGS one-dimensional Branched Lagrangian Solute-Transport Model (BLTM) to simulate the effect of five water-withdrawal scenarios on the salt-front location. The modeled reach contains 132 miles of the lower Hudson River between the Federal Dam at Troy and Hastings-on-Hudson (near New York City). The BRANCH model was calibrated and verified to 19 tidal-cycle discharge measurements made at 11 locations by conventional and acoustic Doppler current-profiler methods. Maximum measured instantaneous tidal flow ranged from 20,000 ft 3 /s (cubic feet per second) at Albany to 368,000 ft 3 /s at Tellers Point; daily-mean flow at Green Island near Troy ranged from 3,030 ft 3 /s to 45,000 ft 3 /s during the flow measurements. Successive ebb- and flood-flow volumes were measured and compared with computed volumes; daily-mean bias was -1.6 percent (range from -21.0 to +23.7 percent; 13.5 percent mean absolute error). Daily-mean deviation between simulated and measured stage at eight locations (from Bowline Point to Albany) over the 19 tidal-cycle measurements averaged +0.06 ft (range from -0.31 to +0.40 ft; 0.21 ft root mean square error, RMSE). These results indicate that the model can accurately simulate flow in the Hudson River under a wide range of flow, tide, and meteorological conditions. The BLTM was used to simulate chloride transport in the 61-mi reach from Turkey Point to Bowline Point under two seasonal conditions in 1990.one representing spring conditions of high inflow and low salinity (April-June), the other representing typical summer conditions of low inflow and high salinity (July-August). Measured chloride concentrations at Bowline Point were used to drive the BLTM simulations, and data collected at West Point were used for calibration. Mean bias in simulated chloride concentration for the April-June 1990 (high flow) data (observed range from 12 to 201 mg/L [milligrams per liter]; 30 mg/L RMSE) was .16 mg/L, and mean bias for the July-August 1990 (low flow) data (observed range from 31 to 2,000 mg/L; 535 mg/ L RMSE) was +126 mg/L. The salt front (saltwater/ freshwater interface) on the Hudson River was defined as the furthest upstream location where the chloride concentration exceeded 100 mg/L. Data from August 1991 were used to evaluate solute transport between West Point and Poughkeepsie because a chloride concentration of 100 mg/L was not observed at Clinton Point in 1990. The BLTM then was used to simulate chloride concentrations at Chelsea Pump Station and Clinton Point. Regression equations, based on daily mean values of specific conductance measured at West Point, were used to estimate daily mean chloride concentrations at Chelsea Pump Station and Clinton Point for model analysis. Mean biases in BLTM-simulated daily mean chloride concentrations for August 1991 were .38 mg/L at Chelsea Pump Station (range from 189 to 551 mg/L; 103 mg/L RMSE) and .9 mg/L at Clinton Point (range from 53 to 264 mg/L; 62 mg/L RMSE). Hypothetical withdrawals at (1) Newburgh, (2) Chelsea, (3) Chelsea and Newburgh, (4) Chelsea and Kingston, and (5) Kingston and Newburgh, were simulated to compute the effects of withdrawals on salt-front movement. Withdrawals of 300 Mgal/d from any combination of Chelsea or Newburgh could result in upstream movement of the salt front of as much as 1.0 mi, given an initial salt-front location between West Point and Rogers Point. Scenarios that included withdrawals at Kingston caused the greatest upstream salt-front movement. Simulation of a 90-day April-June high-flow period during which discharges at Green Island averaged 25,200 ft 3 /s indicated that withdrawals of 1,939 Mgal/d (million gallons per day) at Chelsea Pump Station would not measureably increase chloride concentrations at Chelsea Pump Station under normal tidal and meteorological conditions, but withdrawals at twice that rate (3,878 Mgal/d) could increase the chloride concentration at Chelsea Pump Station to 250 mg/L.

New York↗
USGS1999

Hydrodynamic measurements in Suisun Bay, California, 1992-93

Sea level, velocity, temperature, and salinity (conductivity and temperature) data collected in Suisun Bay, California, from December 11, 1992, through May 31, 1993, by the U.S. Geological Survey are documented in this report. Sea-level data were collected at four locations and temperature and salinity data were collected at seven locations. Velocity data were collected at three locations using acoustic Doppler current profilers and at four other locations using point velocity meters. Sea-level and velocity data are presented in three forms (1) harmonic analysis results, (2) time-series plots (sea level, current speed, and current direction versus time), and (3) time-series plots of the low-pass filtered data. Temperature and salinity data are presented as plots of raw and low-pass filtered time series. The velocity and salinity data collected during this study document a period when the residual current patterns and salt field were significantly altered by large Delta outflow (three peaks in excess of 2,000 cubic meters per second). Residual current profiles were consistently seaward with magnitudes that fluctuated primarily in concert with Delta outflow and secondarily with the spring-neap tide cycle. The freshwater inputs advected salinity seaward of Suisun Bay for most of this study. Except for a 10-day period at the beginning of the study, dynamically significant salinities (>2) were seaward of Suisun Bay, which resulted in little or no gravitational circulation transport.

Water-Resources Investigations Report↗
USGS1971

Techniques and equipment required for precise stream gaging in tide-affected fresh-water reaches of the Sacramento River, California

Current-meter measurements of high accuracy will be required for calibration of an acoustic flow-metering system proposed for installation in the Sacramento River at Chipps Island in California. This report presents an analysis of the problem of making continuous accurate current-meter measurements in this channel where the flow regime is changing constantly in response to tidal action. Gaging-system requirements are delineated, and a brief description is given of the several applicable techniques that have been developed by others. None of these techniques provides the accuracies required for the flowmeter calibration. A new system is described--one which has been assembled and tested in prototype and which will provide the matrix of data needed for accurate continuous current-meter measurements. Analysis of a large quantity of data on the velocity distribution in the channel of the Sacramento River at Chipps Island shows that adequate definition of the velocity can be made during the dominant flow periods--that is, at times other than slack-water periods--by use of current meters suspended at elevations 0.2 and 0.8 of the depth below the water surface. However, additional velocity surveys will be necessary to determine whether or not small systematic corrections need be applied during periods of rapidly changing flow. In the proposed system all gaged parameters, including velocities, depths, position in the stream, and related times, are monitored continuously as a boat moves across the river on the selected cross section. Data are recorded photographically and transferred later onto punchcards for computer processing. Computer programs have been written to permit computation of instantaneous discharges at any selected time interval throughout the period of the current meter measurement program. It is anticipated that current-meter traverses will be made at intervals of about one-half hour over periods of several days. Capability of performance for protracted periods was, consequently, one of the important elements in system design. Analysis of error sources in the proposed system indicates that errors in individual computed discharges can be kept smaller than 1.5 percent if the expected precision in all measured parameters is maintained.

Water Supply Paper↗
USGS2011

Nocturnal activity patterns of northern myotis (Myotis septentrionalis) during the maternity season in West Virginia (USA)

Nocturnal activity patterns of northern myotis (Myotis septentrionalis) at diurnal roost trees remain largely uninvestigated. For example, the influence of reproductive status, weather, and roost tree and surrounding habitat characteristics on timing of emergence, intra-night activity, and entrance at their roost trees is poorly known. We examined nocturnal activity patterns of northern myotis maternity colonies during pregnancy and lactation at diurnal roost trees situated in areas that were and were not subjected to recent prescribed fires at the Fernow Experimental Forest, West Virginia from 2007 to 2009. According to exit counts and acoustic data, northern myotis colony sizes were similar between reproductive periods and roost tree settings. However, intra-night activity patterns differed slightly between reproductive periods and roost trees in burned and non-burned areas. Weather variables poorly explained variation in activity patterns during pregnancy, but precipitation and temperature were negatively associated with activity patterns during lactation. ?? Museum and Institute of Zoology PAS.

Acta Chiropterologica↗
USGS2015

Dim ultraviolet light as a means of deterring activity by the Hawaiian hoary bat Lasiurus cinereus semotus

Widespread bat fatalities at industrial wind turbines are a conservation issue with the potential to inhibit efficient use of an abundant source of energy. Bat fatalities can be reduced by altering turbine operations, but such curtailment decreases turbine efficiency. If additional ways of reducing bat fatalities at wind turbines were available such tradeoffs might not be needed. Based on the facts that bats perceive distant objects primarily through vision and can see in very dim lighting conditions, and the possibility that bats might interact with turbines after approaching them as they would trees, we propose a novel method of reducing bat activity at wind turbines: illumination of the structure with dim light. As a first step toward assessing this approach, we illuminated trees with dim flickering ultraviolet (UV) light in areas frequented by Hawaiian hoary bats Lasiurus cinereus semotus , an endangered subspecies affected by wind turbines. We used a repeated-measures design to quantify bat activity near trees with acoustic detectors and thermal video cameras in the presence and absence of UV illumination, while concurrently monitoring insect numbers. Results indicate that dim UV reduces bat activity despite an increase in insect numbers. Experimental treatment did not completely inhibit bat activity near trees, nor did all measures of bat activity show statistically significant differences due to high variance in bat activity among sites. However, the observed decreases in bat activity with dim UV illumination justify further testing of this method as a means to reduce bat fatalities at wind turbines.

Hawaii↗