Geology ReportsSearch

SEARCH · Geology Reports

Results for “Geologic Investigation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

660 records · Page 8Linked to original sources

Groundwater budget for the Mountain Home area, southern Idaho, 2022–23

The U.S. Geological Survey, with funding from the Idaho Department of Water Resources, developed a groundwater budget for the Mountain Home area in southern Idaho for irrigation year 2023 (November 1, 2022–October 31, 2023). This study focused on the water balance across the Cinder Cone Butte Critical Groundwater Area (CGWA), Mountain Home Groundwater Management Area (GWMA), and the rest of the study area (RoSA), compiling data from various sources, including precipitation records, groundwater level measurements, metered groundwater pumpage data, surface water diversions and evapotranspiration (ET) estimates derived from remote sensing satellite imagery, and ground-based reference data. Key inflow components included recharge from applied surface water irrigation (which incorporates incidental recharge from irrigation practices and conveyance losses), estimated tributary streamflow, and estimated mountain block recharge. The key outflow components were groundwater pumpage for irrigation, municipal, industrial, and domestic uses, and ET. Recharge from applied irrigation and mountain block recharge were the largest inflows, and groundwater pumpage for irrigation was the largest outflow. The CGWA had a positive groundwater budget residual of 2,170 acre-feet (acre-ft), which contrasts with observed long-term groundwater level declines and historical trends of storage depletion. This positive residual is likely associated with unquantified outflows, including lateral groundwater flow out of the subregion, or other complexities, such as overestimated tributary contributions relative to the actual recharge for the 2023 water budget. The GWMA exhibited a positive residual of 56,563 acre-ft, primarily owing to recharge from applied surface water irrigation and areal recharge during a wetter-than-average year, which allowed irrigation entities to deliver more water from in-basin and out-of-basin reservoirs. The RoSA showed a large positive residual of 124,933 acre-ft. The interpretation of these positive residuals must account for significant uncertainties, including estimations of areal recharge, tributary streamflow (particularly losses and diversions), ET, the volume of surface water loss to the Snake River, lateral groundwater flows between subregions and across study area boundaries, and the unquantified groundwater discharge to the Snake River. These uncertainties, in combination with the complex hydrogeologic controls on water movement and limitations of remotely sensed data, directly affect the accuracy of water availability assessments. Future data collection efforts would help reduce these uncertainties and support water resource management decisions in the Mountain Home area. Key efforts could include installing additional streamflow gaging stations (particularly to quantify tributary losses and gains and surface water losses to the Snake River), improving groundwater pumpage metering, and validating remotely sensed ET data with ground-based measurements. Furthermore, to better quantify unrepresented or highly uncertain fluxes, focused investigations on groundwater discharge to the Snake River, lateral groundwater flows between subregions and across study area boundaries, and a more robust determination of the actual influence and volume of mountain block recharge would help refine future water availability assessments for the Mountain Home area.

Idaho

Color-Shaded Relief Bathymetry of Lake Chelan, Washington

In 2023, the U.S. Geological Survey (USGS) completed a 3-week field operation in Lake Chelan, Washington, the third deepest lake in the conterminous United States, to acquire sediment cores, high-resolution bathymetry data, and chirp sub-bottom profiles. The high-resolution bathymetry displayed in this map publication was collected using a Norbit Winghead i67-curved array multibeam system; raw data were cleaned and gridded (3 by 3 meters [m]) in the Teledyne CARIS software. In some locations where the slopes of Lake Chelan are near-vertical, multibeam returns were sparse, resulting in artifacts resembling holes that appear as grey dots within the color-shaded bathymetric relief. Although the 2023 bathymetric mapping of Lake Chelan resulted in similar morphometric characteristics to previous hydrographic campaigns (table 1; Kendra and Singleton, 1987; Pelletier and others, 1989), these new data provide a much more detailed understanding of the two physiographic basins that comprise Lake Chelan: the deeper (as deep as 445.8 m [fig. 1]; previously reported as 453 m) and narrower (1–2 kilometers [km] wide) Lucerne Basin to the north, and the shallower (as deep as 127.8 m [fig. 1]), and wider (2–3 km wide) Wapato Basin to the south. With this detailed imaging of Lake Chelan, we find pervasive morphological evidence of slope failure and mass-transport deposits (MTDs) in at least 89 locations within the lake and 63 subaqueous deltas (fig. 2). The deeper Lucerne Basin is dominated by steep slopes and numerous subaqueous deltas fed by steep fluvial catchments, whereas the Wapato Basin contains numerous landslide scarps, scars, and debris aprons along the more gently sloping lake margins, and abundant relict kettle structures from the Pleistocene deglaciation. Lake Chelan’s geomorphic, geophysical, and sediment data contain important records of glacial retreat and advance, regional volcanic eruptions, and earthquakes that generate ground motions severe enough to induce landslides recorded in the sediment as MTDs. The epicenter of the 1872 Washington State Earthquake (M 6.5–7.2; Bakun and others, 2002; Brocher and others, 2017; Sherrod and others, 2021) is along the Spencer Canyon Fault, near the southern end of Lake Chelan. Shaking from this earthquake was strong enough to affect local aquifers, induce liquefaction of unconsolidated sediments, produce large seiches (Brocher and others, 2018), and likely cause landslides within Lake Chelan.

Washington

Ground-water quality atlas of Oakland County, Michigan

The U.S. Geological Survey (USGS), in cooperation with Oakland County Health Division (OCHD), collected 140 water samples from 38 wells in Oakland County during 1998 to better understand ground-water quality. OCHD had observed temporal variations in concentrations of various constituents, so two additional sets of samples were collected to evaluate potential short-term variability related to sample collection procedures and long-term seasonal variability. Replicate samples from 28 wells were analyzed in the Michigan Department of Environmental Quality (MDEQ) Drinking Water Laboratory to compare MDEQ’s analytical results to those obtained from the USGS National Water Quality Laboratory. Several additional databases describing population, land use, water supply, soils, geology, and flows of ground water and surface water are presented in the first part of the report to assist in interpreting the water-quality data. Maps created from these databases are provided in the first portion of the report as an extension of the study-area description. The U.S. Environmental Protection Agency (USEPA) has established Maximum Contaminant Levels (MCL) and Secondary Maximum Contaminant Levels (SMCL) for which samples were analyzed in this study. Water from the 38 wells sampled by the USGS did not exceed the SMCL or MCL for sulfate, fluoride, or nitrite. However, water from 26 wells exceeded the SMCL for iron, water from 12 wells exceeded the SMCL for manganese, and water from 12 wells exceeded the SMCL for dissolved solids. Water from two wells exceeded the MCL for nitrate, although nitrate concentrations in water from most wells was below the detection limit. Water from seven wells exceeded the SMCL for chloride, and water from all wells contained detectable concentrations of chloride. Water from five wells exceeded the MCL for arsenic, and most of the wells sampled contained detectable concentrations of arsenic. These five wells were identified from previous MDEQ analyses to have elevated arsenic concentrations, and were sampled to obtain additional chemistry information. Replicate samples were collected from 26 of the 38 wells for analysis at the MDEQ Drinking-Water Laboratory to compare the results with the USGS National Water Quality Laboratory. The results of the replicate analyses indicate close agreement between the laboratories, with mean differences for nitrate, chloride, and arsenic of 0.10 milligrams per liter (mg/L) as nitrogen, 6.8 mg/L, and 0.0008 mg/L, respectively between the USGS and MDEQ analyses. Potential health effects associated with ingesting nitrate, chloride, and arsenic are provided with the water-quality data, along with references for further information.

Michigan

Evaluation of best management practices at an edge-of-field site in the Eagle Creek watershed, Ohio, 2012–20

In 2010, the U.S. Geological Survey worked in partnership with the Great Lakes Restoration Initiative and the Natural Resources Conservation Service to identify farm fields in priority watersheds—watersheds critically important to Great Lake health. Intensive best management practices were implemented in five States to test the efficacy of best management practices, also referred to as agricultural conservation practices, to reduce sediment and nutrient runoff on agricultural fields. These fields were chosen as representatives of the priority watersheds because their farming practices and geographical conditions were common among farms in those watersheds. A farm site located near Findlay, Ohio, in the Eagle Creek watershed used two conservation practices, cover crop (Natural Resources Conservation Service practice standard 340) and variable rate technology (VRT; Natural Resources Conservation Service practice standard 590), which represent common practices in the Maumee priority watershed. This study monitored surface runoff and subsurface tile runoff at the Eagle Creek watershed site. The effects of cover crop and VRT nutrient application on sediment and nutrient runoff were assessed from October 2012 to September 2020. Cover crops were applied in fall of 2016, 2017, and 2018, coinciding with VRT applications. The following parameters were analyzed as part of the study: runoff discharge; peak discharge; and concentrations and loads of total phosphorus, particulate phosphorus, dissolved reactive phosphorus, and suspended sediment. High peak runoff events disproportionally affected nutrient concentrations and loads in runoff. A threshold of the 85th percentile of the peak discharge was chosen to assess the effect of cover crop and VRT nutrient application on nutrient mitigation at each gage. Runoff events below the 85th percentile were considered small, and runoff events over the 85th percentile were considered large. Concentrations from collected water-quality samples were used for the analysis; estimated concentrations were excluded from the statistical evaluation. All surface runoff parameters during small runoff events, except surface runoff volume, were significantly lower in the period with cover crops and VRT implementation. Contrarily, subsurface runoff parameters during small events were not statistically different between the periods with and without cover crops and VRT implementation. Surface and subsurface parameters during large events were also not statistically different between the periods with and without cover crops and VRT implementation. These results indicate cover crops and VRT may improve water quality during small runoff events, but additional best management practices that mitigate large runoff events may lead to greater water-quality improvement given the contribution of large events to overall losses.

Ohio

Reconnaissance basement geology and tectonics of North Zealandia

New rock dredge samples supply key information to establish the tectonic and geological framework of the northern two-thirds of the 95% submerged Zealandia continent. The R/V Investigator voyage IN2016T01 to the Fairway Ridge, Coral Sea, obtained poorly sorted poly-lithologic pebbly to cobbly sandstones, well sorted fine grained sandstones, mudstones, bioclastic limestones, and basaltic lavas. Post-cruise analytical work comprised petrography, whole rock geochemical and Sr and Nd isotopic analyses, and U-Pb zircon, Rb-Sr, and Ar-Ar geochronology. A Fairway Ridge cobbly sandstone has a ∼95 Ma (early Late Cretaceous) depositional age; two biotite granite cobbles are 111 ± 1 and 128 ± 1 Ma in age, and some volcanic pebbles are also likely Early Cretaceous. Fairway Ridge basalts have intraplate alkaline chemistry and are of Late Eocene age (∼40–36 Ma). By analogy with South Zealandia, we interpret strong positive continental magnetic anomalies of North Zealandia to mainly result from Late Cretaceous to Cenozoic intraplate basalts, many of them rift-related lavas. A new basement geological map of North Zealandia shows the position of the Mesozoic Gondwana magmatic arc axis (Median Batholith) and other major geological units. This study completes onland and offshore reconnaissance geological mapping of the entire 5 Mkm 2 Zealandia continent.

Tectonics

Hydrologic investigation of water level fluctuations at Moreau Lake, Moreau Lake State Park, town of Moreau, New York

The causes of water level fluctuations at Moreau Lake, within Moreau Lake State Park in the town of Moreau, New York, were investigated from 2016 to 2021 after lake water levels dropped between 2015 and 2016, raising concerns about the loss of a shallow swimming area at the park beach. Annual variation in precipitation records from the area did not account for the lake water level decline. Two possible causes for the low lake water levels were investigated: the increase in groundwater withdrawals from new residential development since about 2000 and seasonal changes (nongrowing and growing seasons) in precipitation. Investigation of the potential effects of nearby groundwater withdrawals required the compilation and collection of well-log data, seismic surveys, and measurements of lake and groundwater levels, field chemical parameters, and water isotopes to define the hydrogeologic system and to estimate water use. The net result of this work was the determination that Moreau Lake is a “flow though” lake with no surface water outlet; groundwater enters the lake on the upgradient side and exits through the downgradient side, however, groundwater does not flow southward from the lake toward nearby groundwater withdrawals from the semiconfined aquifer, and thus groundwater withdrawals were unlikely to have an effect on lake water levels. Investigation of the historic precipitation records during nongrowing (November through April) and growing (May through October) indicated that (1) nongrowing season precipitation from 2011–12 to 2015–16 was more deficient than any similar period during the past 78 years and (2) since about 2000, nongrowing seasons have been drier overall and growing seasons have been considerably wetter. Initiation of lake water level monitoring in 2016 provided an opportunity to compare seasonal precipitation with seasonal lake water level changes. Nongrowing season lake water levels are very sensitive to precipitation, such that high precipitation (40 percent above the seasonal median) resulted in a 5-foot rise in lake water level. In contrast, the growing season lake water levels are sensitive to dry conditions; for example, deficient rainfall (about 6 percent below the seasonal median) resulted in a decline of lake water levels of about 3.5 feet. However, lake water levels are insensitive to high growing season rainfall inputs (about 10 to 47 percent above the seasonal median); lake water levels consistently declined about by 0.8 feet above this range of seasonal excessive precipitation.

New York

Water quality of Rob Roy Reservoir and Lake Owen, Albany County, and Granite Springs and Crystal Lake Reservoirs, Laramie County, Wyoming, 1997-98

The water quality of four reservoirs was assessed during 1997 and 1998 as a cooperative project between the Cheyenne Board of Public Utilities and the U. S. Geological Survey. The four reservoirs, Rob Roy, Lake Owen, Granite Springs, and Crystal Lake, provide approximately 75 percent of the public water supply for Cheyenne, Wyoming. Samples of water and bottom sediment were collected and analyzed for selected physical, chemical, and biological characteristics to provide data about the reservoirs. Water flows between the reservoirs through a series of pipelines and stream channels. The reservoirs differ in physical characteristics such as elevation, volume, and depth. Profiles of temperature, dissolved oxygen, specific conductance, and pH were examined. Three of the four reservoirs exhibited stratification during the summer. The profiles indicate that stratification develops in all reservoirs except Lake Owen. Stratification developed in Rob Roy, Granite Springs, and Crystal Lake Reservoirs by mid-July in 1998 and continued until September, with the thickness of the epilimnion increasing during that time. Secchi disk readings indicated Rob Roy Reservoir had the clearest water of the four reservoirs studied. The composition of the phytoplankton community was different in the upper two reservoirs from that in the lower two reservoirs. Many of the species found in Rob Roy Reservoir and Lake Owen are associated with oligotrophic, nutrient-poor conditions. In contrast, many of the species found in Granite Springs and Crystal Lake Reservoirs are associated with mesotrophic or eutrophic conditions. The total number of taxa identified also increased downstream. The chemical water type in the reservoirs was similar, but dissolved-solids concentrations were greater in the downstream reservoirs. Water in all four reservoirs was a calcium-bicarbonate type. In the fall of 1997, Rob Roy Reservoir had the lowest dissolved-solids concentration (19 milligrams per liter), whereas Crystal Lake Reservoir had the highest concentration (63 milligrams per liter). Relatively little differences in the concentrations of major-ion species were noted between samples collected near the surface and near the bottom of the same reservoir. In contrast, iron and manganese concentrations generally were higher in samples collected near the bottom of a reservoir than in near-surface samples collected from the same reservoir. Composite bottom-sediment samples from all four reservoirs contained similar concentrations of bulk constituents such as aluminum, iron, phosphorus and titanium, but varied in concentrations of trace elements. Trace-element concentrations in Rob Roy Reservoir and Lake Owen were similar to the crustal average, whereas in Granite Springs and Crystal Lake Reservoirs the concentrations were similar to granitic rocks.

Wyoming

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic units�an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida

Streams, springs, and volcanic lakes for volcano monitoring

Introduction Volcanic unrest can trigger appreciable change to surface waters such as streams, springs, and volcanic lakes. Magma degassing produces gases and soluble salts that are absorbed into groundwater that feeds streams and lakes. As magma ascends, the amount of heat and degassing will increase, and so will any related geochemical and thermal signal. Subsurface magma movement can cause pressurization that alters hydrostatic head and may induce groundwater discharge. Fluid-pressure changes have been linked to distal volcano-tectonic earthquakes (White and McCausland, 2016; Coulon and others, 2017) and phreatic eruptions (for example, Yamaoka and others, 2016). Clearly, changes in groundwater and surface waters are both indicators of unrest and clues to how and where magma is rising toward the surface. Where possible, it is prudent to incorporate real-time hydrologic data into multiparameter monitoring of restless volcanoes. Hydrologic dynamics can also be tracked by changes in groundwater levels that are commonly measured in shallow boreholes (see of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume, on boreholes; Hurwitz and Lowenstern, 2024). Although inferred to be common, relatively few volcano-hydrology anomalies are well documented, and many are essentially anecdotal (Newhall and others, 2001), reflecting the fact that high-resolution time series remain rare. Extreme examples include the 2008 eruption of Nevado del Huila, Colombia, where relatively minor phreatomagmatic eruptions were accompanied by expulsion of as much as 300 million cubic meters of groundwater from fissures high on the volcano (Worni and others, 2011), generating large lahars. Substantial decreases in flow rate from springs about 8 kilometers from the summit of Mayon Volcano, Philippines, have been noted before most eruptions in the 20th century (Newhall and others, 2001). Stream monitoring at Redoubt Volcano in 2009 allowed Werner and others (2012) to recognize that groundwater was unable to absorb (or scrub) the high flux of volcanic gas and that a high CO 2 /SO 2 precursor signal had been evident for 5 months prior to the eruption. A key to better interpreting hydrologic anomalies—or even identifying them—is therefore obtaining adequate baseline data. Most hydrologic monitoring at U.S. volcanoes has been accomplished by intermittent sampling surveys with annual or less frequent sampling (for example, https://hotspringchem.wr.usgs.gov/index.php ). More frequent sampling, however, generally is needed to establish reliable baselines. A recent hydrologic and hydrothermal monitoring experiment at 25 sites and 10 of the 12 level 4 (very high threat) volcanoes in the U.S. portion of the Cascade Range demonstrated that there is sufficient temporal variability in hydrothermal fluxes, even during quiescent periods, that one-time measurements will commonly have limited interpretive value (Crankshaw and others, 2018). Thus, surveys are best augmented with data from streamgages (for example, Evans and others, 2004; Bergfeld and others, 2008). Streamflow (water discharge) data allow measured temperature and specific conductance to be converted to heat and solute mass fluxes, which could be insightful parameters for detecting anomalous activity (McCleskey and others, 2012). At the Yellowstone Caldera, long-term monitoring of river solutes has allowed calculation of the chloride flux, a proxy for heat discharge (Hurwitz and others, 2007; McCleskey and others, 2016) from the subsurface magma. This is readily accomplished because data from streamgages are continuously recorded and archived by the U.S. Geological Survey (USGS) National Water Information System (NWIS) (USGS, 2024). Similar studies on stratovolcanoes or shield volcanoes would be scientifically useful, and yet are logistically challenging, requiring streamgages on numerous radial drainages complemented by either frequent manual sampling or numerous deployments of equipment to measure water temperature and specific conductance as a proxy for water chemistry. Another challenge is that some volcanic areas, especially shield volcanoes, are characterized by near-surface porous rocks and soils, such that surface streams are rare and replaced by distant, dilute large-volume springs with only a trace of any original volcanically sourced water (Manga, 2001; Hurwitz and others, 2021). Volcanic lakes are worthy of special attention for monitoring efforts, as their temperature and composition can provide evidence of increased flux of volatile-rich fluids from below. Quantifying changes in volatile and heat release from magma can be simpler in lakes than for volcanoes with radial drainages and no major lakes. Moreover, volcanic lakes pose a range of hazards themselves, including phreatomagmatic eruptions, debris flows, flank collapse, tsunamis, and toxic gas release (Mastin and Witter, 2000; Delmelle and others, 2015; Manville, 2015; Rouwet and others, 2015)—hazards that have historically been responsible for substantial loss of life at many volcanoes worldwide (Manville, 2015). Catastrophic CO 2 release at Lake Nyos, Cameroon, in 1986 suffocated about 1,750 people and about 3,500 livestock and was probably triggered by a large landslide into the gas-saturated lake (Kling and others, 1987; Evans and others, 1993). Gas-charged springs in Soda Bay within Clear Lake (California) have caused almost a dozen deaths to bathers in the past hundred years (ABC News, 2000). A 2005 example of lake overturn and abundant gas release was documented at Mount Chiginagak in Alaska (Schaefer and others, 2008) but did not result in any human casualties. Although thermally stratified lakes, which promote trapping of exsolved magmatic gas, tend to develop in tropical regions, the phenomenon can also arise where salinity creates meromixis (a condition in which a lake does not mix completely), as occurs in Mono Lake, California (Jellison and Melack, 1993; Jellison and others, 1998). If magma erupts or flows into a lake, the interaction between hot magma and cold water can be explosive (Mastin and others, 2004; Zimanowski and others, 2015) and substantially expand the area affected by the eruption. Another hazard is the breaching of crater rims by landslides triggered by volcanic and (or) seismic activity. Under some circumstances, substantial volumes of water can be displaced, leading to large floods and lahars. Late Holocene lake flooding from Aniakchak Crater in the Alaska Peninsula (Waythomas, 2022) and from Paulina Lake in Newberry Crater, Oregon (Chitwood and Jensen, 2000), caused by the failure of outlet sills, testify to the substantial hazards at lake-filled calderas. Several volcanic systems in the United States host lakes known to receive heat and gas from underlying magma. These lakes vary widely in area, depth, and chemical composition. Lakes are present at level 4 volcanoes, including Crater Lake and Newberry Volcano in Oregon; Yellowstone Caldera in Wyoming; Long Valley Caldera, Clear Lake volcanic field, Medicine Lake, and Salton Buttes in California; and Aniakchak Crater, Mount Katmai, Fisher Caldera, Mount Okmok, and Kaguyak Crater, among others, in Alaska. A water lake was present in Halemaʻumaʻu, the crater of Kīlauea, Hawai‘i (fig. F1), from October 2019 to December 2020. Level 3 volcanoes with lakes include Mono Lake volcanic field (Calif.), Mount Bachelor (Ore.), Ukinrek Maars and Mount Chiginagak (Alaska), and Soda Lake (Nevada). In addition, there are lakes at many levels 1 and 2 volcanoes. In the United States, there are no strongly acidic lakes that receive abundant input of magmatic gas, such as those found at Mount Ruapehu (New Zealand), Ijen and Kelud (Indonesia), and Poás (Costa Rica). Nevertheless, many contain fluids that provide clues to magmatic processes below. Since publication of a previous report on recommended instrumentation for volcano monitoring (Moran and others, 2008), continuous hydrologic monitoring has become increasingly feasible. However, changes in water pressure, temperature, and chemistry remain, in general, poorly studied phenomena at volcanoes (Sparks, 2003; National Academies of Sciences, Engineering, and Medicine, 2017). Recent efforts by the USGS have included the temporary study of Cascade Range volcanoes, which included frequent (15 minute to hourly) temporal sampling of temperature, depth, and conductivity (Crankshaw and others, 2018; Ingebritsen and Evans, 2019). At Yellowstone Caldera, many streamgages have now added thermistors and specific conductance sensors, allowing estimation of time-dependent chloride flux as a proxy for variations in subsurface heat flux (McCleskey and others, 2012, 2016). Efforts to better understand lakes have also accelerated, with bathymetric mapping and sampling carried out at several locations in the United States. Especially thorough work was done at Yellowstone Lake thanks to the Hydrothermal Dynamics of Yellowstone Lake (HD-YLAKE, https://hdylake.org ) project, funded primarily by the National Science Foundation. In addition to geophysical surveys and recovery of cores and other samples, HD-YLAKE investigations included remotely operated vehicle (ROV) investigations of hydrothermal vents on the lake floor (fig. F2). Data collected by the ROV provided a better understanding of the thermal and chemical influx from lake-bottom hydrothermal systems (Sohn and others, 2017). In this chapter, we focus on detecting changes in the chemistry, temperature, discharge, or water levels of streams, springs, and lakes that can be caused by seismicity, volumetric strains, or increases in gas flux associated with ascending magma. There is unavoidable overlap with other chapters of this report. Samples of water and gas can also be obtained in boreholes ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume; Hurwitz and Lowenstern, 2024), both shallow and deep. Gas monitoring ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–E, 11 p., https://doi.org/10.3133/sir20245062e.">chapter E , this volume; Lewicki and others, 2024) relies in part on samples from springs and wells, particularly where measurable gas plumes are absent. Water acts as a trigger and lubricant for landslides and sediment-rich floods, and so hydrology has obvious relevance for lahar monitoring, as discussed in of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–H, 6 p., https://doi.org/10.3133/sir20245062h. ">chapter H (this volume; Thelen and others, 2024). Shared situational awareness among scientists engaged in geophysical, gas, and hydrologic monitoring will improve overall understanding of the volcanic hazard.

Scientific Investigations Report

Flood-Inundation Maps of the Current and Jacks Fork Rivers including the Ozark National Scenic Riverways, Southeast Missouri, 2023

Digital flood-inundation maps for a 131.8-mile reach of the Current River and a 44.6-mile reach of the Jacks Fork River, in southeast Missouri, were created by the U.S. Geological Survey (USGS) in cooperation with the Ozark Foothills Regional Planning Commission and the South Central Ozark Council of Governments. The maps also encompass the 134 miles of the Current and Jacks Fork Rivers within the Ozark National Scenic Riverways, which is the first national park area to protect a river system. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Program website at https://water.usgs.gov/osw/flood_inundation/ , depict estimates of the areal extent and depth of flooding corresponding to selected water levels (hereafter referred to as “stages”) at eight reference USGS streamgages—five on the Current River (USGS station numbers 07064440, 07064533, 07066510, 07067000, and 07068000) and three on the Jacks Fork River (USGS station numbers 07065200, 07065495, and 07066000). Near-real-time stages at these streamgages may be obtained from the USGS National Water Information System at https://doi.org/10.5066/F7P55KJN or the National Weather Service National Water Prediction Service at http://water.noaa.gov/ , which also forecasts flood hydrographs at four of these sites (USGS station numbers 07067000, 07068000, 07065495, and 07066000). Flood profiles were computed for seven of the eight map reaches by means of two-dimensional hydraulic models and the remaining reach by a one-dimensional hydraulic model. The models were calibrated by using stage-streamflow relations or streamflow measurements at the USGS streamgages and from high-flow stage measurements from water-level loggers distributed throughout the reaches. The hydraulic models were used to compute water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datums. The profile stages ranged from the National Weather Service “action stage” or near bankfull, to a stage exceeding the highest recorded water level at each streamgage. The simulated water-surface profiles were then combined with a digital elevation model (derived from light detection and ranging data having a nonvegetated vertical accuracy of a maximum 10-centimeter root mean square error) to delineate the area flooded at each water level and the associated water depths. The availability of these maps, along with information regarding current stage from the USGS streamgage and forecasted high-flow stages from the National Weather Service, will provide emergency management personnel, resource managers, and residents with information that is critical for flood-response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Missouri

Emerging investigator series: Post-wildfire sediment geochemical characterization reveals manganese reactivity and a potential link to water quality impairment in the Gallinas Creek watershed, New Mexico

Water quality post-wildfire is often impaired by increased turbidity and elevated concentrations of elements such as manganese (Mn) and iron (Fe). Precipitation events exacerbate these issues, due in part to increased erosion and transport of sediment from hillslopes to surface water. Both Mn and Fe are major redox-active elements in sediments that drive a variety of biogeochemical cycles, precipitate adsorptive phases, and can themselves be drinking water contaminants. By investigating Mn and Fe sediment geochemistry in post-wildfire sediment deposits, related water quality hazards can be assessed. To establish and strengthen this connection, we analyzed the geochemistry of sediment deposits and surface water in the Gallinas Creek watershed, New Mexico over 1.5 years post-wildfire. Analyses included particle size analysis, water extractions, sequential extractions and aqua regia extractions to determine metal partitioning in sediment deposits. Data demonstrate Mn concentrations were distributed across labile and reactive fractions, such as the exchangeable and oxyhydroxide fractions, while Fe concentrations were mainly associated with the residual fraction. Manganese concentrations in aqua regia extractions and several fractions of sequential extractions were also strongly and significantly correlated with fine-grained sediment while the same pools of Fe concentrations were not. Dissolved Mn concentrations in surface water were elevated (>50 μg L −1 ) multiple times over the 1.5 years post-wildfire, highlighting a relationship between sediment geochemistry and water quality. This work shows Mn in sediments mobilized post-wildfire has an influence on water quality and highlights how further investigation into Mn sediment redox processes and mineralogy post-wildfire can inform risk assessments and resource management.

New Mexico

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri River near Kansas City, Missouri, August 8–9, 2023

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near 8 bridge crossings of the Missouri River near Kansas City, Missouri, on August 8–9, 2023. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches that extended about 1,550 to 1,640 feet longitudinally and generally extended laterally across the active channel from bank to bank during low floodflow to nonflood conditions. These surveys provided the channel geometry and hydraulic conditions of the river at the time of the surveys and provided characteristics of scour holes, which may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. The data collected from the surveys may also be useful to the Missouri Department of Transportation as a record of low floodflow conditions in regards to the stability and integrity of the bridges with respect to bridge scour. Bathymetric data were collected around every in-channel pier. Scour holes were at most piers where bathymetry could be obtained, except for those piers on banks or surrounded by riprap. All the bridge sites in this study were surveyed and documented in previous studies. The average difference between the bathymetric surfaces ranged from 0.07 to 4.16 feet higher in 2023 than 2019, which indicates overall deposition between the survey dates, as might be expected based purely on streamflow at the time of the survey. However, the average difference between the bathymetric surfaces ranged from 1.44 feet higher to 1.88 feet lower in 2023 than 2015, which indicates a dynamic equilibrium of scour and deposition overall between those surveys, despite the lower flow conditions in 2023. Similarly, the average difference between the bathymetric surfaces ranged from 3.18 feet higher to 5.19 feet lower in 2023 than 2011, which indicates a relative equilibrium between scour and deposition overall, albeit the trend was toward scour as might be expected because of the substantial flood event in 2011. Riprap blankets and alignment to flow had a substantial effect on the size of the scour hole for a given pier. Piers that were partially or fully surrounded by riprap blankets had scour holes that were substantially smaller (to nonexistent) compared to piers with no rock or riprap and effectively mitigated the scour holes historically observed at these piers. Several of the structures had piers that were skewed to primary approach flow. At most of the structures, the scour hole was deeper and longer on the side of the pier with impinging flow than the leeward side, with some amount of deposition on the leeward side, as typically observed at piers skewed to approach flow.

Kansas, Missouri

Flood-inundation maps of the Blue River and major tributaries in and near Kansas City, Missouri, 2023–25

Digital flood-inundation maps for 35.5 miles of the Blue River, in and near Kansas City, Missouri, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Kansas City. Maps were also developed for a combined 7.3 miles of Brush Creek (4.4 miles) and Indian Creek (2.9 miles), two primary tributaries to the Blue River in the study reach. The flood-inundation maps, available through the USGS Flood Inundation Mapping Program website at https://water.usgs.gov/osw/flood_inundation/ , depict estimates of the areal extent and depth of flooding, depth of water above first-floor elevations in selected buildings, water velocity, water-surface elevations, and time of travel corresponding to selected water levels or gage heights (hereafter referred to as “stages”) at nine reference USGS streamgages—five on the Blue River (USGS station numbers 06893590, 06893578, 06893500, 06893150, and 06893100), two on Brush Creek (USGS station numbers 06893562 and 06893557), one on Indian Creek (USGS station number 06893390), and one on the Missouri River (USGS station number 06893000). Near-real-time stages at these streamgages may be obtained from USGS Water Data for the Nation at https://doi.org/10.5066/F7P55KJN or the National Weather Service National Water Prediction Service at http://water.noaa.gov/ , which also forecasts flood hydrographs at seven of these sites (USGS station numbers 06893000, 06893590, 06893578, 06893500, 06893150, 06893557, and 06893390). Flood profiles were computed for eight map reaches by means of two-dimensional hydraulic models. The models were calibrated using the USGS-developed stage–streamflow relations at each reference streamgage. Two map reaches on the lower Blue River also include the effects of backwater from the Missouri River on flood inundation extent and hydraulic characteristics. The hydraulic models were used to compute water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datums. The profile stages ranged from the National Weather Service “Action Stage” or near bankfull to a stage exceeding the highest recorded water level at each streamgage. The simulated water-surface profiles were then combined with a digital elevation model (derived from light detection and ranging data having a nonvegetated vertical accuracy of a maximum 10-centimeter root-mean-square error) to delineate the area flooded at each water level and the associated hydraulic characteristics. The availability of these maps, along with information regarding current stage from the USGS streamgage and forecasted high-flow stages from the National Weather Service, will provide emergency management personnel, resource managers, and residents with information that could be critical for flood-response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Kansas, Missouri

Near-surface geophysics: Environmental applications

The field of geophysics encompasses a broad and diverse compilation of methodologies that employs principles of physics to characterize properties of earth materials within the subsurface. While geophysical methods have a long history in resource exploration and studies of Earth’s interior, the subdiscipline of “near-surface geophysics” has evolved in recent decades for examination of the shallow, near-surface environment for a range of purposes ranging from archaeological or forensic investigations to assessment of geologic, hydrologic, biologic, and geochemical properties and processes. “Environmental geophysics” are near-surface geophysical studies and methods that focus on understanding natural systems (e.g., watershed hydrology, groundwater–surface water connections, biophysical processes) as well as research pertaining to anthropogenic impacts and land management, (e.g., contamination and remediation, saltwater intrusion, agricultural practices). This field can be further subdivided into subdisciplines focused on specific topics and applications, such as water resources and hydrology (hydrogeophysics) or biologic and microbial processes (biogeophysics). Studies in environmental geophysics span a range of scales, from pore-scale laboratory tests to watershed-scale or regional field experiments. Methods vary by the nature of physics employed, the specific measurement acquired, and how that data is ultimately processed and analyzed to produce interpretable results. There exists further diversity in the acquisition logistics, geometry, and timing of data collection. Geophysical data can be collected in boreholes (one-dimensional, 1-D, vertical profiles), along survey lines (two-dimensional, 2-D, cross-sections), or in dense sensor arrays or gridded profiles (three-dimensional, 3-D, models). Regarding the temporal aspect, studies can conduct one-time geophysical surveys to obtain detailed imaging of subsurface structure or use timelapse and continuous monitoring to investigate variations in subsurface properties over time. The cumulation of all possible permutations of these factors (method, acquisition geometry, survey design, and target application) results in an immense diversity among environmental geophysical studies. Nevertheless, this field remains unified in the pursuit of understanding natural and human-impacted near-surface environments through geophysical investigations. Here we highlight some key references within environmental geophysics. Resources on geophysical theory, acquisition logistics, processing and inversion workflows, and example case studies are categorized into the most common geophysical classes within Geophysical Methods. Lastly, example references for the dominant types of applications in environmental geophysical studies are catalogued in Environmental Applications.

Book chapter

Archean to Mesozoic–Cenozoic seismic crustal structure: Implications for geological and biological evolution

We use >4500 measurements of crustal structure to investigate the seismic structure of continental crust, Archean to Mesozoic–Cenozoic. The mean crustal thickness of continents, including their margins, is 36.5 km. We find that Archean, Paleoproterozoic, and Mesoproterozoic crust have similar mean crustal thickness (41 km), seismic velocities, Vp/Vs ratio, and density. Crusts of these ages span 3 Ga, from 4.0 to 1.0 Ga, and their similarity of physical properties (thickness, density, and seismic velocities) suggests that the process of crustal formation may have been similar during this time period, which covers 66% of Earth's history. Neoproterozoic crustal properties differ significantly from Mesoproterozoic and older crusts. The mean thickness of Neoproterozoic crust is 32 km, some 9 km thinner than the mean thickness of Archean, Paleoproterozoic, and Mesoproterozoic crust. A lithospheric root with a thickness of 150–200 km underlies Archean, Paleoproterozoic, and Mesoproterozoic crusts, and this root resists lithospheric rifting and crustal extension and thinning. Based on these observations, particularly the lithospheric thickness, we conclude that Archean, Paleoproterozoic, and Mesoproterozoic lithosphere are unique and together form the stable cratonic nuclei, defined as the thick (150–250 km), long-lived cores of continents. Higher mantle temperatures during the Archean, Paleoproterozoic, and Mesoproterozoic may have played a key role in the formation of the thick lithospheric roots. The second key finding is that the similarities of mean seismic properties indicate that the process of crustal formation operating in the Archean continued during the Paleoproterozoic and Mesoproterozoic. The thin (mean value < 135 km) lithospheric root beneath Neoproterozoic and younger crust may be related to the steady decrease in mantle temperature through time. Neoproterozoic and Paleozoic crust have similar physical properties, and these eras are characterized by pronounced biodiversification, including the renowned Garden of Ediacara, the Cambrian Explosion, and the Great Ordovician Biodiversification. Mesozoic–Cenozoic crust is the most diverse and reflects the current tectonic and magmatic processes of crustal formation.

Book chapter

Hydrogeologic framework of the Mountain Home area, southern Idaho

In the arid western Snake River Plain around the City of Mountain Home, Idaho, declining groundwater levels concern agricultural, municipal, and other water users who rely on groundwater for sustenance because surface-water resources are limited. The U.S. Geological Survey developed this hydrogeologic framework to provide an updated characterization of groundwater resources in the western Snake River Plain around the City of Mountain Home. The hydrogeologic framework comprises: (1) a conceptual description of hydrogeologic units, (2) a three-dimensional hydrogeologic model and borehole database, (3) a map of groundwater levels and change, and (4) a discussion of groundwater occurrence and movement within the study area. Hydrogeologic units were defined based on existing literature and the borehole database compiled for this study; the five hydrogeologic units are granite, rhyolite, basalt, fine-grained sediments, and coarse-grained sediments. Each unit can bear water, but the main regional aquifer in the study area occurs in the basalt and fine-grained sediment units with depth to water ranging from 150 to 765 feet. A perched groundwater zone near the City of Mountain Home is primarily hosted in basalt and used domestically with most depths to water ranging from 30 to 100 feet. Interflow zones, scoria, and vertical fractures create heterogeneity within the basalt hydrogeologic unit that exerts strong control on groundwater movement, creating horizontal perching conditions and zones of enhanced vertical conductivity that facilitate downward groundwater percolation. In the fine- and coarse-grained sediments and rhyolite units, inferred faults both impede and enhance groundwater movement. The borehole database was constructed by digitizing 540 well-driller reports and was used to build a three-dimensional hydrogeologic framework model which reasonably represents the spatial distribution of hydrogeologic units in the study area. Generally, fine-grained sediments underlie much of the study area, with basalt concentrated in the central and western study area and rhyolite and granite in the uplands to the north. Groundwater levels were measured in 180 wells in March and November 2023; these data were used to develop water-table contour maps and describe groundwater-level change over an irrigation season. Groundwater generally flows south-southwest to the Snake River and groundwater levels declined across most of the study area (from 0.03 to 22.01 feet) between spring and autumn 2023, which is consistent with long-term declines in the Cinder Cone Butte Critical Groundwater Area and Mountain Home Groundwater Management Area. Groundwater levels rose (0.6 to 15.44 feet) over the irrigation season in most wells in the perched groundwater zone near the City of Mountain Home and near the Snake River, indicating the importance of surface-water recharge to groundwater in areas where surface water irrigation occurs. In aggregate, this hydrogeologic framework provides an updated characterization of and new insights into groundwater resources in the study area to help inform water resources management.

Idaho