Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Progress Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76Linked to original sources
USGS1987

Source of salts in the Waianae part of the Pearl Harbor aquifer near Barbers Point water tunnel, Oahu, Hawaii

The salinity of the water supply of Barbers Point Naval Air Station has increased markedly since 1983. The Naval Air Station obtains its water, about 3 million gal/day, from Barbers Point shaft, a water shaft that taps the Waianae part of the Pearl Harbor aquifer underlying the dry, southeastern flank of the Waianae mountains on the island on Oahu, Hawaii. From 1983 to 1985 the chloride concentration of the water, increased from 220 to 250 mg/L and has remained near that level through 1986. The EPA has established 250 mg/L as the maximum recommended chloride concentration in drinking water because above that level many people can taste the salt. The high chloride concentration in shallow groundwater at all wells in the area indicates that most of the salts in the freshwater lens are contributed by rainfall, sea spray, and irrigation return water. At Barbers Point shaft, pumping may draw a small amount of saltwater from the transition zone and increase the chloride concentration in the pumped water by about 20 mg/L. Salinity of the lens decreases progressively inland in response to recharge from relatively fresher water and in response to an increasing lens thickness with increasing distance from the shoreline. The increase, in 1983, in the chloride concentration of water at the shaft was most probably the result of saltier recharge water reaching the water table, and not the result of increased mixing of underlying saltwater with the freshwater. The chloride concentration of the recharge water has probably increased because, in 1980, the drip method of irrigation began to replace the furrow method on sugarcane fields near the shaft. A mixing-cell model was used to estimate the effect of drip irrigation on the chloride concentration of the groundwater in the vicinity of Barbers Point shaft. The model predicted an increase in chloride concentration of about 50 mg/L. The observed increase was about 30 mg/L and the chloride concentration is presently stable at 245 to 250 mg/L; hence, the chloride concentration is not expected to increase significantly more. (Lantz-PTT)

Water-Resources Investigations Report↗
USGS2018

Predicting biological conditions for small headwater streams in the Chesapeake Bay watershed

A primary goal for Chesapeake Bay watershed restoration is to improve stream health and function in 10% of stream miles by 2025. Predictive spatial modeling of stream conditions, when accurate, is one method to fill gaps in monitoring coverage and estimate baseline conditions for restoration goals. Predictive modeling can also monitor progress as additional data become available. We developed a random forests model to predict biological condition of small streams (<200 km 2 in drainage) in the Chesapeake Bay watershed. Biological condition was measured with the Chesapeake Bay Basin-wide Index of Biotic Integrity (Chessie BIBI), a stream macroinvertebrate index. Our goal was to predict biological condition in all unsurveyed small streams present in a 1:24,000 scale catchment layer as a 2004–2008 baseline. We reclassified the 5-category Chessie BIBI ratings into two categories, poor and fair/good, to align with management goals of the Chesapeake Bay Program. The model included 12 geospatial predictor variables including measures on spatial location, bioregion, land cover, soil, precipitation, and number of dams in local catchments. We trained the model with a random 75% subset of Chessie BIBI data ( n = 1449), and used the remaining 25% of Chessie BIBI data ( n = 484) as test data. The model performed well, correctly predicting 72% of samples in training data and 73% of samples in test data, but model accuracy varied among bioregions. We performed uncertainty analyses by adding bands of either ±0.05 or ±0.10 BIBI units to the cutoff between poor and fair/good. These uncertainty analyses resulted in 14.5% (±0.05 band) and 24.8% (±0.10 band) of samples in test data being classified as in uncertain condition. For 95,877 small stream reaches in the Chesapeake Bay watershed, the model predicted 64% in fair/good condition, the ±0.05 uncertainty analyses predicted 57% in fair/good condition, and the ±0.10 uncertainty analysis predicted 50% in fair/good condition. These reported values have different implications for the number of improved stream miles required to meet the goal of improving 10%. Incorporating uncertainty provides an assessment of model strength as well as confidence in predictions. We, therefore, suggest increased reporting of uncertainty in studies that spatially predict stream conditions.

Chesapeake Bay watershed↗
USGS2004

Triangle area water supply monitoring project, October 1988 through September 2001, North Carolina -- description of the water-quality network, sampling and analysis methods, and quality-assurance practices

The Triangle Area Water Supply Monitoring Project was initiated in October 1988 to provide long-term water-quality data for six area water-supply reservoirs and their tributaries. In addition, the project provides data that can be used to determine the effectiveness of large-scale changes in water-resource management practices, document differences in water quality among water-supply types (large multiuse reservoir, small reservoir, run-of-river), and tributary-loading and in-lake data for water-quality modeling of Falls and Jordan Lakes. By September 2001, the project had progressed in four phases and included as many as 34 sites (in 1991). Most sites were sampled and analyzed by the U.S. Geological Survey. Some sites were already a part of the North Carolina Division of Water Quality statewide ambient water-quality monitoring network and were sampled by the Division of Water Quality. The network has provided data on streamflow, physical properties, and concentrations of nutrients, major ions, metals, trace elements, chlorophyll, total organic carbon, suspended sediment, and selected synthetic organic compounds. Project quality-assurance activities include written procedures for sample collection, record management and archive, collection of field quality-control samples (blank samples and replicate samples), and monitoring the quality of field supplies. In addition to project quality-assurance activities, the quality of laboratory analyses was assessed through laboratory quality-assurance practices and an independent laboratory quality-control assessment provided by the U.S. Geological Survey Branch of Quality Systems through the Blind Inorganic Sample Project and the Organic Blind Sample Project.

North Carolina↗
USGS2019

Gas hydrate production testing – Knowledge gained

Since their initial discovery in the 1960’s, gas hydrates have been considered to be an important potential source of unconventional natural gas. Significant progress has been made relative to our understanding of the geologic and engineering controls on the ultimate energy potential of gas hydrate; however, more work is required to realize the promise of gas hydrates as a future energy source. Gas hydrates have been encountered, recovered or inferred to exist in numerous sedimentary basins in Arctic permafrost settings, regions of alpine permafrost, marine sediments of outer continental margins and in deep lakes. Despite the great abundance of potential gas hydrate resources in the world, a large portion of these resources reside in clay-rich sediments and fracture dominated reservoir systems, and are not generally considered producible with existing technology, but may have future potential with the emergence of new technologies. For a large portion of the world, gas hydrate in sand reservoirs have become a viable production target and the focus of the first production testing efforts. Production tests in Arctic Canada (Mackenzie Delta) and Alaska have shown that gas can be produced from highly-concentrated gas hydrate accumulations in coarse-grained (i.e., sand rich) reservoir systems with conventional production technologies. Production can be achieved through the depressurization method and by more complex methods such as molecular substitution (e.g., CO2-CH4 exchange). In 2013, the gas hydrate production test was conducted in a marine setting in the offshore of Japan. An additional test was conducted in Japan in 2017 to further evaluate alternative well completion technologies. Also in 2018, China initiated a 60-day gas hydrate production test in the Shenhu region of the South China Sea. This report reviews the results of gas hydrate engineering and production testing studies associated with the Mallik, Mount Elbert, and Iġnik Sikumi projects in northern Canada and Alaska. The results of the marine gas hydrate producing testing efforts in the Nankai Trough (Japan) and in the South China Sea (China) are also summarized

Conference Paper↗
USGS2013

Serum chemistry, hematologic, and post-mortem findings in free-ranging bobcats ( Lynx rufus ) with notoedric mange

Notoedric mange was responsible for a population decline of bobcats ( Lynx rufus ) in 2 Southern California counties from 2002–2006 and is now reported to affect bobcats in Northern and Southern California. With this study we document clinical laboratory and necropsy findings for bobcats with mange. Bobcats in this study included free-ranging bobcats with mange (n = 34), a control group of free-ranging bobcats without mange (n = 11), and a captive control group of bobcats without mange (n = 19). We used 2 control groups to evaluate potential anomalies due to capture stress or diet. Free-ranging healthy and mange-infected bobcats were trapped or salvaged. Animals were tested by serum biochemistry, complete blood count, urine protein and creatinine, body weight, necropsy, and assessment for anticoagulant rodenticide residues in liver tissue. Bobcats with severe mange were emaciated, dehydrated, and anemic with low serum creatinine, hyperphosphatemia, hypoglycemia, hypernatremia, and hyperchloremia, and sometimes septicemic when compared to control groups. Liver enzymes and leukocyte counts were elevated in free-ranging, recently captured bobcats whether or not they were infested with mange, suggesting capture stress. Bobcats with mange had lower levels of serum cholesterol, albumin, globulin, and total protein due to protein loss likely secondary to severe dermatopathy. Renal insufficiency was unlikely in most cases, as urine protein:creatinine ratios were within normal limits. A primary gastrointestinal loss of protein or blood was possible in a few cases, as evidenced by elevated blood urea nitrogen, anemia, intestinal parasitism, colitis, gastric hemorrhage, and melena. The prevalence of exposure to anticoagulant rodenticides was 100% (n = 15) in bobcats with mange. These findings paint a picture of debilitating, multisystemic disease with infectious and toxic contributing factors that can progress to death in individuals and potential decline in populations.

Journal of Parasitology↗
USGS2008

An evaluation of selected extraordinary floods in the United States reported by the U.S. Geological Survey and implications for future advancement of flood science

Thirty flood peak discharges determine the envelope curve of maximum floods documented in the United States by the U.S. Geological Survey. These floods occurred from 1927 to 1978 and are extraordinary not just in their magnitude, but in their hydraulic and geomorphic characteristics. The reliability of the computed discharge of these extraordinary floods was reviewed and evaluated using current (2007) best practices. Of the 30 flood peak discharges investigated, only 7 were measured at daily streamflow-gaging stations that existed when the flood occurred, and 23 were measured at miscellaneous (ungaged) sites. Methods used to measure these 30 extraordinary flood peak discharges consisted of 21 slope-area measurements, 2 direct current-meter measurements, 1 culvert measurement, 1 rating-curve extension, and 1 interpolation and rating-curve extension. The remaining four peak discharges were measured using combinations of culvert, slope-area, flow-over-road, and contracted-opening measurements. The method of peak discharge determination for one flood is unknown. Changes to peak discharge or rating are recommended for 20 of the 30 flood peak discharges that were evaluated. Nine floods retained published peak discharges, but their ratings were downgraded. For two floods, both peak discharge and rating were corrected and revised. Peak discharges for five floods that are subject to significant uncertainty due to complex field and hydraulic conditions, were re-rated as estimates. This study resulted in 5 of the 30 peak discharges having revised values greater than about 10 percent different from the original published values. Peak discharges were smaller for three floods (North Fork Hubbard Creek, Texas; El Rancho Arroyo, New Mexico; South Fork Wailua River, Hawaii), and two peak discharges were revised upward (Lahontan Reservoir tributary, Nevada; Bronco Creek, Arizona). Two peak discharges were indeterminate because they were concluded to have been debris flows with peak discharges that were estimated by an inappropriate method (slope-area) (Big Creek near Waynesville, North Carolina; Day Creek near Etiwanda, California). Original field notes and records could not be found for three of the floods, however, some data (copies of original materials, records of reviews) were available for two of these floods. A rating was assigned to each of seven peak discharges that had no rating. Errors identified in the reviews include misidentified flow processes, incorrect drainage areas for very small basins, incorrect latitude and longitude, improper field methods, arithmetic mistakes in hand calculations, omission of measured high flows when developing rating curves, and typographical errors. Common problems include use of two-section slope-area measurements, poor site selection, uncertainties in Manning’s n -values, inadequate review, lost data files, and insufficient and inadequately described high-water marks. These floods also highlight the extreme difficulty in making indirect discharge measurements following extraordinary floods. Significantly, none of the indirect measurements are rated better than fair, which indicates the need to improve methodology to estimate peak discharge. Highly unsteady flow and resulting transient hydraulic phenomena, two-dimensional flow patterns, debris flows at streamflow-gaging stations, and the possibility of disconnected flow surfaces are examples of unresolved problems not well handled by current indirect discharge methodology. On the basis of a comprehensive review of 50,000 annual peak discharges and miscellaneous floods in California, problems with individual flood peak discharges would be expected to require a revision of discharge or rating curves at a rate no greater than about 0.10 percent of all floods. Many extraordinary floods create complex flow patterns and processes that cannot be adequately documented with quasi-steady, uniform one-dimensional analyses. These floods are most accurately described by multidimensional flow analysis. Within the U.S. Geological Survey, new approaches are needed to collect more accurate data for floods, particularly extraordinary floods. In recent years, significant progress has been made in instrumentation for making direct discharge measurements. During this same period, very little has been accomplished in advancing methods to improve indirect discharge measurements. Greater use of paleoflood hydrology could fill many shortcomings of U.S. Geological Survey flood science today, such as enhanced knowledge of flood frequency. Additional links among flood runoff, storm structure, and storm motion would provide more insight to flood hazards. Significant improvement in understanding flood processes and characteristics could be gained from linking radar rainfall estimation and hydrologic modeling. Additionally, more could be done to provide real-time flood-hazard warnings with linked rainfall/runoff and flow models. Several important recommendations are made to improve the flood-documentation capability of the U.S. Geological Survey. When very large discharges are measured by current meter or hydroacoustics, water-surface slope should be measured as well. This measurement would allow validation of roughness values that can significantly extend the discharge range of verified Manning’s n for 1-dimensional and 2-dimensional flow analyses. At least two of the floods investigated may have had flow so unstable that large waves affected the interpretation of high-water marks. Instability criteria should be considered for hydraulic analysis of large flows in high-gradient, smooth channels. The U.S. Geological Survey needs to modernize its toolbox of field and office practices for making future indirect discharge measurements. These practices could include, first and foremost, a new peak-flow file database that allows greater description and interpretation of flow events, such as stability criteria in high-gradient, smooth channels, debris flow documentation, and details of flood genesis (hurricane, snowmelt, rain-on-snow, dam failure, and the like). Other modernized practices could include (a) establishment of calibrated stream reaches in chronic flash flood basins to expedite indirect computation of flow; (b) development of process-based theoretical rating curves for streamflow-gaging stations; (c) adoption of step-backwater models as the standard surface-water modeling tool for U.S. Geological Survey field offices; (d) development and support for multidimensional flow models capable of describing flood characteristics in complex terrain and high-gradient channels; (e) greater use of the critical-depth method in appropriate locations; (f) deployment of non-contact instruments to directly measure large floods, rather than attempting to reconstruct them; (g) increased use of paleoflood hydrology; and (h) assurance that future collection of hydro-climatic data meets the needs of more robust watershed models.

Scientific Investigations Report↗
USGS2011

Formation of nanocolloidal metacinnabar in mercury-DOM-sulfide systems

Direct determination of mercury (Hg) speciation in sulfide-containing environments is confounded by low mercury concentrations and poor analytical sensitivity. Here we report the results of experiments designed to assess mercury speciation at environmentally relevant ratios of mercury to dissolved organic matter (DOM) (i.e., <4 nmol Hg (mg DOM) −1 ) by combining solid phase extraction using C 18 resin with extended X-ray absorption fine structure (EXAFS) spectroscopy. Aqueous Hg(II) and a DOM isolate were equilibrated in the presence and absence of 100 μM total sulfide. In the absence of sulfide, mercury adsorption to the resin increased as the Hg:DOM ratio decreased and as the strength of Hg-DOM binding increased. EXAFS analysis indicated that in the absence of sulfide, mercury bonds with an average of 2.4 ± 0.2 sulfur atoms with a bond length typical of mercury-organic thiol ligands (2.35 Å). In the presence of sulfide, mercury showed greater affinity for the C 18 resin, and its chromatographic behavior was independent of Hg:DOM ratio. EXAFS analysis showed mercury–sulfur bonds with a longer interatomic distance (2.51–2.53 Å) similar to the mercury–sulfur bond distance in metacinnabar (2.53 Å) regardless of the Hg:DOM ratio. For all samples containing sulfide, the sulfur coordination number was below the ideal four-coordinate structure of metacinnabar. At a low Hg:DOM ratio where strong binding DOM sites may control mercury speciation (1.9 nmol mg –1 ) mercury was coordinated by 2.3 ± 0.2 sulfur atoms, and the coordination number rose with increasing Hg:DOM ratio. The less-than-ideal coordination numbers indicate metacinnabar-like species on the nanometer scale, and the positive correlation between Hg:DOM ratio and sulfur coordination number suggests progressively increasing particle size or crystalline order with increasing abundance of mercury with respect to DOM. In DOM-containing sulfidic systems nanocolloidal metacinnabar-like species may form, and these species need to be considered when addressing mercury biogeochemistry.

Environmental Science & Technology↗
USGS2017

Field-trip guide to Columbia River flood basalts, associated rhyolites, and diverse post-plume volcanism in eastern Oregon

The Miocene Columbia River Basalt Group (CRBG) is the youngest and best preserved continental flood basalt province on Earth, linked in space and time with a compositionally diverse succession of volcanic rocks that partially record the apparent emergence and passage of the Yellowstone plume head through eastern Oregon during the late Cenozoic. This compositionally diverse suite of volcanic rocks are considered part of the La Grande - Owyhee eruptive axis (LOEA), an approximately 300-kilometer-long (185 mile), north - northwest - trending, middle Miocene to Pliocene volcanic belt located along the eastern margin of the Columbia River flood basalt province. Volcanic rocks erupted from and preserved within the LOEA form an important regional stratigraphic link between the (1) flood basalt - dominated Columbia Plateau on the north, (2) bimodal basalt - rhyolite vent complexes of the Owyhee Plateau on the south, (3) bimodal basalt-rhyolite and time-transgressive rhyolitic volcanic fields of the Snake River Plain - Yellowstone Plateau, and (4) the High Lava Plains of central Oregon. This field-trip guide describes a 4 - day geologic excursion that will explore the stratigraphic and geochemical relationships among mafic rocks of the Columbia River Basalt Group and coeval and compositionally diverse volcanic rocks associated with the early “Yellowstone track” and High Lava Plains in eastern Oregon. Beginning in Portland, the Day 1 log traverses the Columbia River gorge eastward to Baker City, focusing on prominent outcrops that reveal a distal succession of laterally extensive, large-volume tholeiitic flood lavas of the Grande Ronde, Wanapum, and Saddle Mountains Basalt formations of the CRBG. These “great flows” are typical of the well-studied flood basalt-dominated Columbia Plateau, where interbedded silicic and calc-alkaline lavas are conspicuously absent. The latter part of Day 1 will highlight exposures of middle to late Miocene silicic ash-flow tuffs, rhyolite domes, and calc-alkaline lava flows overlying the CRBG across the northern and central parts of the LOEA. The Day 2 field route migrates to southern parts of the LOEA, where rocks of the CRBG are associated in space and time with lesser known and more complex silicic volcanic stratigraphy associated with middle Miocene, large-volume, bimodal basalt-rhyolite vent complexes. Key stops will provide a broad overview of the structure and stratigraphy of the middle Miocene Mahogany Mountain caldera and middle to late Miocene calc-alkaline lavas of the Owyhee basalt. Stops on Day 3 will progress westward from the eastern margin of the LOEA, examining a transition linking the Columbia River Basalt-Yellowstone province with a northwestward-younging magmatic trend of silicic volcanism that underlies the High Lava Plains of eastern Oregon. Initial field stops on Day 3 will examine key outcrops demonstrating the intercalated nature of middle Miocene tholeiitic CRBG flood basalts, prominent ash-flow tuffs, and “Snake River-type” large-volume rhyolite lava flows exposed along the Malheur River. Subsequent stops on Day 3 will focus upon the volcanic stratigraphy northeast of the town of Burns, which includes regional middle to late Miocene ash-flow tuffs, and lava flows assigned to the Strawberry Volcanics. The return route to Portland on Day 4 traverses across the western axis of the Blue Mountains, highlighting exposures of the widespread, middle Miocene Dinner Creek Tuff and aspects of Picture Gorge Basalt flows and northwest-trending feeder dikes situated in the central part of the CRBG province.

Oregon↗
USGS2023

National preparedness strategy & action plan for potentially hazardous near-Earth objects and planetary defense

Near-Earth Objects (NEOs) are asteroids and comets that orbit the Sun, but have orbits that can bring them into Earth’s neighborhood—within 30 million miles of Earth’s orbit. Planetary defense is “applied planetary science” to address the NEO impact risks on Earth. This National Preparedness Strategy and Action Plan for Near-Earth Objects and Planetary Defense (2023 Planetary Defense Strategy) updates the United States’ first comprehensive Near-Earth Object Preparedness Strategy and Action Plan, released in 2018. The 2023 Planetary Defense Strategy builds on existing efforts by Federal Departments and Agencies to address the hazard of near-Earth object impacts, includes evaluation of where progress has been made since 2018, and focuses future work on planetary defense across the U.S. government. The 2023 Planetary Defense Strategy maintains and updates the core five goals of the 2018 Strategy and Action Plan, while adding a sixth goal to improve governance and interagency coordination on planetary defense issues across Federal Departments and Agencies for the decade ahead. The 2023 Planetary Defense Strategy focuses on six goals: • Goal 1: Enhance NEO detection, tracking, and characterization capabilities. • Goal 2: Improve NEO modeling, prediction, and information integration. • Goal 3: Develop technologies for NEO deflection and disruption missions. • Goal 4: Increase international cooperation on NEO preparation. • Goal 5: Strengthen and routinely exercise NEO impact emergency procedures and action protocols. • Goal 6: Improve U.S. governance of planetary defense through new interagency collaboration.

Report↗
USGS2004

Hydrogeology and ground-water flow at Levee 31N, Miami-Dade County, Florida, July 2003 to May 2004: As part of the Comprehensive Everglades Restoration Plan

Introduction The Levee 31N Seepage Management Pilot Project began in 2001, as part of the Comprehensive Everglades Restoration Plan (CERP). The pilot project seeks to determine the appropriate technology needed to control seepage from Everglades National Park (ENP), and provide the appropriate amount of ground-water flow to minimize potential impacts to the West Well Field and Biscayne Bay. To meet these needs, a levee cut-off wall (vertical subsurface barrier) has been proposed along Levee 31N in Miami-Dade County to reduce seepage flow from ENP. During the wet season, ground water would be captured by wells adjacent to Levee 31N and diverted into a buffer area adjacent to ENP where sheetflow would be reestablished. An integrated, multidisciplinary investigation of ground-water flow is currently in progress by the South Florida Water Management District (SFWMD) and U.S. Army Corps of Engineers as part of the Levee 31N Seepage Management Pilot Project. Pre-seepage pilot wall ground-water flow patterns are being assessed through use of in situ heat-pulse flowmeter measurements, monitoring the vertical changes in hydraulic head and temperature, ground-water age dating, and measurement of the vertical change in ambient ground-water quality. A high-resolution hydrogeologic framework is needed as part of this effort. In 2003, the U.S. Geological Survey (USGS) initiated a study to characterize the surficial aquifer system in detail to a depth of about 100 feet below ground level in the Levee 31N study area, and to delineate karst preferential ground-water flow zones. This study was part of a cooperative agreement between the USGS and the SFWMD (USGS Joint Funding Agreement No. 04E0FL208011 and SFWMD Agreement No. CPO40324), and funded through CERP.

Florida↗
USGS2018

Research to improve ShakeAlert earthquake early warning products and their utility

Earthquake early warning (EEW) is the rapid detection of an earthquake and issuance of an alert or notification to people and vulnerable systems likely to experience potentially damaging ground shaking. The level of ground shaking that is considered damaging is defined by the specific application; for example, manufacturing equipment may experience damage at a lower intensity ground shaking than would cause damage to a building. Along the West Coast of the United States, the warning times for ground shaking could range as high as tens of seconds for moderate levels of ground shaking, or potentially longer, if a lower ground-shaking threshold is used to issue alerts. However, it is not always possible to provide advance warning of ground shaking, particularly for locations close to an earthquake that are most likely to experience very strong ground shaking. EEW alerts may be useful to individuals who can use a few seconds to move to a safe zone and to electromechanical systems that can take automatic actions to reduce damage and injuries. An EEW system, ShakeAlert, has been under development in the United States since 2006. Federal and State governments, as well as the private sector, are now investing in the ShakeAlert prototype system that will, when completed, become an operational public system for the West Coast of the United States. While the current prototype is delivering alerts to test users, improvements to the accuracy, timeliness, and utility of the alerts are needed. For this reason, it is essential that the ShakeAlert system be continuously improved through targeted research, involving not only the current ShakeAlert partner organizations, but also the broader scientific, engineering, and emergencyresponse communities. To this end, this report describes the opportunities for improvement that can be addressed through research and development over the next 5 years. Our recommendations are organized into four areas: (1) understand EEW capabilities and user needs, (2) make alerts as fast and accurate as possible, (3) ensure reliability when it counts, and (4) explore the use of new instrumentation. The first challenge is to understand EEW capabilities and user needs. EEW must deliver actionable information to people and to automated systems to mitigate short- and longterm impacts of damaging ground shaking, so development of EEW must be motivated by the needs of users. Within this challenge, we must study the technical capabilities and limitations of EEW in general, and the ShakeAlert system specifically. This includes development of performance metrics that assess the timeliness and accuracy of alerts to understand the value and utility of the ShakeAlert EEW product(s) for various user groups, including different industry sectors, emergency-management agencies, and the public. Research is needed to define the alerting choices that maximize the utility of the system for users and to determine what the available communication pathways are for providing timely alert information. Additionally, we engage users to assess how alerts will be used by different sectors to mitigate losses and to inform EEW product design. Further, social-science research is needed to develop alert messaging, including what relevant prior and follow-up information are required, to ensure effective use of alerts. The second challenge is to make alerts as fast and as accurate as possible. The timeliness and accuracy of an EEW alert is important because it will set in motion a series of actions and downstream products. An EEW alert will trigger notification across emergency-alert systems and across multiple communication channels to populations in impacted regions. The EEW alert region may grow as the earthquake fault-rupture length increases, and the EEW system’s characterization of it, evolves. We must continue research into new or improved seismic and geodetic waveform-processing methods necessary to rapidly characterize the expected ground shaking and associated uncertainties. It is important to thoroughly evaluate whether new methods improve alerts through more accurate ground-motion estimates and (or) reduced latencies (that is, longer warning times). New methods could include tracking the extent of a large rupture in real time (known as finite-fault algorithms) and ground-motionbased EEW algorithms. Additionally, ground motion predictions could be optimized for each earthquake as the earthquake fault rupture progresses by using, for example, event terms to shift ground-motion curves for more (or less) energetic ruptures. The third challenge is to ensure reliability when it counts. This challenge requires us to explore approaches that assess the expected performance of ShakeAlert across the range of earthquake magnitudes, locations, and depths that may occur within the alerting region. Large, damaging earthquakes and their associated aftershock sequences matter most for hazard and for EEW, but these large-earthquake sequences occur infrequently. We expect ShakeAlert to respond robustly to these large-earthquake sequences despite potentially long periods of relative seismic quiescence in the intervening years, and in spite of inevitable communication challenges that arise during and after a large earthquake. We must develop methods to utilize the broadest available datasets to test EEW performance, including ground-motion data recorded in other parts of the world. The observational period for large, damaging earthquakes in any particular region has been short in comparison to estimated large-earthquake recurrence times. Ground-motion records for very large, damaging western United States events and major aftershock sequences do not yet exist, nor do data exist for all potential sources of noise and spurious signals that ShakeAlert must be “tuned” to reject. In addition, robust synthetic data could provide the flexibility to test a wider range of earthquake magnitude, tectonic-setting, and noise scenarios than are covered by existing observational data. Synthetic ground-motion data must be thoroughly vetted against records of smaller magnitude earthquakes to ensure that they accurately capture both the onset and the amplitude of the ground shaking. The final challenge is to explore the use of new instrumentation. The development of EEW around the world to date has focused on the use of high-quality, scientific-grade seismic and geodetic instrumentation. The use of additional types of instrumentation or information may also improve EEW products by filling gaps in sensor coverage in countries that already have dense seismic networks or enable EEW in countries without such networks. We must keep up with these developments and continuously assess their value in supplementing existing EEW systems, such as ShakeAlert, or enabling EEW where such systems do not exist. Such developments include low-cost instrumentation with microelectromechanical system (MEMS) sensors and global positioning system (GPS)/global navigation satellite system (GNSS) antennas embedded in low-cost consumer electronics, sea-floor seismometers, geodetic instrumentation deployed along the Cascadia and Alaska megathrust margins of western North America, and borehole strainmeters that are already deployed across the region.

Open-File Report↗
USGS2015

Development, evolution, and destruction of the saline mineral area of Eocene Lake Uinta, Piceance Basin, western Colorado

Halite and the sodium bicarbonate mineral nahcolite were deposited in Eocene-age saline Lake Uinta in the Piceance Basin, northwestern Colorado. Variations in the areal extent of saline mineral deposition through time were studied using descriptions of core and outcrop. Saline minerals have been extensively leached by groundwater, and the original extent of saline deposition was determined from the distribution of empty vugs and collapse breccias. Because vugs and breccias strongly influence groundwater movement, determining where leaching has occurred is an important consideration for in-situ oil shale extraction methods currently being developed. Lake Uinta formed when two much smaller freshwater lakes, one in the Uinta Basin and the other in the Piceance Basin, expanded and coalesced across the Douglas Creek arch. Early Lake Uinta inherited much of the topography in the freshwater lake and surrounding alluvial plains that preceded it, and the deep central lake area of Lake Uinta developed largely over the offshore area of the freshwater lake. A prolonged period of infilling followed the formation of Lake Uinta, creating broad lake-margin shelves prior to the onset of saline mineral deposition. These shelves almost certainly played a critical role in the evolution of the brine layer that accumulated in the deep central lake area. Broad marginal shelves formed as well around the Uinta Basin part of Lake Uinta. Brines that formed on those shelves also probably migrated to the deep central lake area in the Piceance Basin, as no saline minerals were deposited in the Uinta Basin until late in the history of Lake Uinta. Oil shale in the deep central lake consists of interbedded laminate oil shale beds that originated within the deep lake area, and blebby and streaked oil shale beds that were transported into the deep lake area by sediment gravity flows. Blebby and streaked oil shale beds contain carbonate clasts and siliciclastic clasts similar to lithologies found on the marginal shelves. It is possible that these clasts and the highly saline brines that evolved on the marginal shelves were incorporated into the same gravity flows. Saline mineral deposition is informally subdivided into early, middle, and late phases. During the early phase, nahcolite and rich oil shale were deposited in the deep central lake area, and carbonate-rich sandstone, siltstone, and mudstone and ostracodal, oolitic, algal limestone were deposited on the marginal shelves. During the middle saline mineral phase, oil shale deposition gradually expanded across the marginal shelves, and by the end of that phase, oil shale deposition covered almost all of the former shelf areas. An increasing flow of water from Lake Gosiute to the north, as it was gradually filled in by volcaniclastics, may have caused this expansion. Saline mineral deposition also expanded during the middle saline mineral phase, reaching to near the former shelf break by the end of that phase. This suggests that the former shelf break remained a topographic feature that confined the deep saline brine layer throughout the middle phase. By the beginning of the late saline mineral phase, Lake Gosiute had been completely filled in and volcaniclastic debris reached the northern shore of Lake Uinta. This initiated a north-to-south infilling of the Piceance Basin part of Lake Uinta that progressively pushed the saline mineral area southward and ultimately onto the former marginal shelf areas in the southern part of the basin. A saline mineral area formed for the first time in the eastern part of the Uinta Basin during this infilling and, for a time, saline minerals were deposited in both basins. By the end of the late saline phase, the Piceance Basin part of Lake Uinta was filled in and saline mineral deposition shifted entirely into the Uinta Basin. Leaching of saline minerals began sometime after the Green River Formation was lithified enough to allow collapse breccias to form. Leaching is ongoing today, indicated by the discharge of highly saline water from a series of springs in the northern part of the basin. Groundwater invasion and saline mineral dissolution is commonly incomplete in areas that lack fractures, leaving behind pockets of unleached saline minerals in otherwise leached intervals. Today, the base of the leached zone slopes toward the north and toward the area where the brines are being discharged.

Colorado, Utah, Wyoming↗
USGS2007

Using a novel micro-sampling technique to monitor the effects of methylmercury on the eggs of wild birds

Methylmercury is the predominant chemical form of mercury reported in the eggs of wild birds. The embryo is the life stage at which birds are most sensitive to methylmercury. Protective guidelines have been based largely on captive-breeding studies done with chickens (Gallus domesticus), mallards (Anas platyrhynchos), and ring-necked pheasants (Phasianus colchicus). Typically these studies are cost and time prohibitive. In the past, researchers have used either egg injections or the ?sample egg? technique to determine contaminant effects on bird eggs. Both techniques have their limitations. As an alternative to the above methods and because most of the methylmercury is found in the albumen we have developed a novel, less invasive technique, to micro-sample the albumen of eggs in the field. An albumen sample would be analyzed and then compared to the hatching success of that egg. Using the micro-sampling procedure, the egg is oriented with the blunt end up and the pointed end down. A vent hole is drilled at the top to relieve pressure. Approximately one third up from the bottom, a withdrawal site is drilled just until the inner shell membrane is exposed. A syringe with a 21 or 18 gauge needle is gently inserted just into the egg and approximately 200?300?l of albumen is removed. Almost concurrently this site and then the vent are sealed. Thus far we have experimented with both chicken and mallard eggs in the laboratory. We sampled chicken eggs at days 0 and 3 of incubation with a hatching success of 76% and 70%, respectively. Neither group was significantly different from control eggs (P=0.52, 0.54). Field studies are in progress using this technique in which birds are allowed to incubate their own eggs. We envision micro-sampling to be a tool that researchers and managers could use in the field to determine the effects of mercury or other contaminants in bird populations. Micro-sampling would reduce the impact on the sampled population and could be used to monitor sensitive species without impacting reproduction and recruitment.

Proceedings of the Annual Conference of the Southe↗
USGS2023

Damage amplification during repetitive seismic waves in mechanically loaded rocks

Cycles of stress build-up and release are inherent to tectonically active planets. Such stress oscillations impart strain and damage, prompting mechanically loaded rocks and materials to fail. Here, we investigate, under uniaxial conditions, damage accumulation and weakening caused by time-dependent creep (at 60, 65, and 70% of the rocks’ expected failure stress) and repeating stress oscillations (of ± 2.5, 5.0 or 7.5% of the creep load), simulating earthquakes at a shaking frequency of ~ 1.3 Hz in volcanic rocks. The results show that stress oscillations impart more damage than constant loads, occasionally prompting sample failure. The magnitudes of the creep stresses and stress oscillations correlate with the mechanical responses of our porphyritic andesites, implicating progressive microcracking as the cause of permanent inelastic strain. Microstructural investigation reveals longer fractures and higher fracture density in the post-experimental rock. We deconvolve the inelastic strain signal caused by creep deformation to quantify the amount of damage imparted by each individual oscillation event, showing that the magnitude of strain is generally largest with the first few oscillations; in instances where pre-existing damage and/or the oscillations’ amplitude favour the coalescence of micro-cracks towards system scale failure, the strain signal recorded shows a sharp increase as the number of oscillations increases, regardless of the creep condition. We conclude that repetitive stress oscillations during earthquakes can amplify the amount of damage in otherwise mechanically loaded materials, thus accentuating their weakening, a process that may affect natural or engineered structures. We specifically discuss volcanic scenarios without wholesale failure, where stress oscillations may generate damage, which could, for example, alter pore fluid pathways, modify stress distribution and affect future vulnerability to rupture and associated hazards.

Scientific Reports↗
USGS2017

Monitoring Hawaiian biodiversity: Pilot study to assess changes to forest birds and their habitat

Biological diversity, or biodiversity, is the variety and abundance of species in a defined area, and is one of the oldest and most basic descriptions of biological communities. Understanding how populations and communities are structured and change over space and time in response to internal and external forces is a management priority. Effective management practices and conservation strategies depend on our understanding of the relationship between changes in biodiversity and ecological drivers such as invasive species, land use and climate change. To demonstrate how changes in biodiversity may be monitored over a large (400 km2) tract of native forest habitat, we compared bird and plant community composition and structure in an upper montane region of Hawai‘i Island originally surveyed in 1977 as part of the Hawai‘i Forest Bird Survey (Scott et al. 1986) with a comprehensive sample of the same region in 2015. Our findings suggest that across a region spanning an elevation range of 600 to 2,000 m considerable changes occurred in the plant and bird communities between 1977 and 2015. Endemic and indigenous plants species richness (i.e., total number of species) decreased dramatically in the low and middle elevations below an invasive weed front, whereas naturalized plant species richness did not change between the two periods at any elevation. Endemic bird abundance decreased and two species were lost in the lower elevations (< 1,100 m) between 1977 and 2015, while naturalized bird abundance and the numbers of species increased in the same area. In addition to changes in community composition, the structure of the forest showed evidence of changes in dominant and sub-dominant tree canopy cover, shrub and herbaceous cover, dominant tree canopy height, and matted fern cover. Biodiversity monitoring helps to define specific conservation targets and to measure progress towards reaching those targets. It is difficult to ascribe causative factors to a change in biodiversity without directly manipulating the environment. Forest habitat in a variety of settings (i.e., islands and regions with differing land-use histories and elevation ranges), however, can provide opportunities to evaluate the influence of ecological drivers. Declines in native bird biodiversity in low-elevation areas may be attributed to invasive species as land use and climate conditions have remained relatively similar over the 40-year period. Thus, the shift from an endemic-naturalized co-dominated community in 1977 to one dominated by naturalized, alien birds in 2015, and reduction in native bird abundance over that period, may reflect increasing dominance by naturalized plants within this forested area. Inferences drawn from analyses of region-wide surveys, especially with replicate datasets, will facilitate the identification of broad-scale changes in biodiversity, and provide a needed current datum in Hawaiian plant and bird biodiversity monitoring.

Hawaii↗
USGS1992

Water, Energy, and Biogeochemical Budgets (WEBB) program: Data availability and research at the Northern Temperate Lakes site in north-central Wisconsin

More than three thousand kettle lakes, widely dispersed within a mixed temperate forest ecosystem, are predominant features of the Northern Highland area of north-central Wisconsin. A hydrological and biogeochemical investigation of seven of these lakes and their watershed area is currently in progress as part of the Water, Energy, and Biogeochemical Budgets (WEBB) program of the U.S. Geological Survey. The objectives of the overall WEBB program are to: (1) improve understanding of processes controlling water, energy, and biogeochemical fluxes in freshwater systems, the interactions among those processes, and their relations to climatic variables; and (2) improve the capability to predict freshwater, energy, and biogeochemical budgets over a range of spatial and temporal scales. The focus of the WEBB project in Wisconsin is hydrologic research in the Northern Temperate Lakes (NTL) area of the state. Based on the premise that an understanding of hydrologic and biogeochemical cycles in the watershed is predicated on a thorough understanding of the individual components that control the water flow, the project involves a detailed study of the hydrologic budget, including the roles of rainfall, streamflow, ground water, and flow in the unsaturated zone. It also involves investigation of ground-water/ surface-water interactions. The objectives of the Northern Temperate Lakes WEBB project are to: (1) describe processes controlling water and solute fluxes in the NTL watersheds; (2) examine interactions among those processes and their relations to climatic variables; and (3) improve the capability to predict changes in water and solute fluxes for a range of spatial and temporal scales. A variety of procedures will be used to address the objectives of the project including: installation of piezometers, lysimeters, stream-gaging sites, precipitation collectors, climate-monitoring instruments; analysis of transport of nutrients and other solutes through the system; analysis of changes in isotopic composition of water; and temperature profiling. The implementation of these procedures is described in this report. The NTL-WEBB study area includes seven lakes that are also the site of a Long-Term Ecological Research (LTER) project, sponsored by the National Science Foundation. This project incorporates diverse research investigations conducted by faculty and research associates of the University of Wisconsin-Madison. The research orientation of NTL-LTER is principally toward aquatic ecology and geochemistry of the lakes. The WEBB research plan, with its emphasis on hydrologic processes in the lake watersheds, is designed to complement and enhance the LTER work.

Wisconsin↗
USGS1936

Floods in the United States — Magnitude and frequency

From time immemorial floods have transformed beneficent river waters into a menace to humanity. Man's progress toward economic stability has been repeatedly halted or even thrown backward by the interruption of his efforts to make effective use of rivers and of valley lands. This handicap is not imposed by the destructiveness of large rivers alone, or of rivers in widely separated areas, for there are few if any streams, brooks, or rivulets that are not subject to flows beyond their channel capacities. Yet, though man for ages has suffered seriously from recurring floods, he has not been deterred from continuing to extend his activities in areas that are virtually foredoomed to flood damage. Today in the United States serious floods may occur in any section in any year, and even, in some regions, several times a year. Many of these floods leave behind them the tragedy of death and disease and of property irreparably damaged. The aggregate direct property damage caused by floods in this country has been estimated roughly to average $35,000,000 a year. In addition there are serious indirect and intangible losses of great but not precisely calculable magnitude.

Water Supply Paper↗
USGS2020

Benthic infaunal communities of Baltimore and Norfolk Canyons

The imperative for finding, cataloging, and understanding continental margin diversity derives from the many key functions, goods and services provided by margin ecosystems and by an increasingly deleterious human footprint on our continental slopes (Levin and Dayton 2009). Progress in seafloor mapping technology and direct observation has revealed unexpected heterogeneity, with a mosaic of habitats and ecosystems linked to geomorphological, geochemical, and hydrographic features that are capable of influencing biotic diversity (Levin and Sibuet 2012). Submarine canyons are dramatic and widespread topographic features crossing continental and island margins in oceans, connecting shelf-margins to deep ocean basins (Harris and Whiteway 2011). Their importance as biodiversity hotspots has continued to emerge over the last two decades as research efforts have increased. Understanding the physical parameters within a canyon system is a primary factor for understanding habitat variability and ecological patterns within the confines of canyon systems (Levin et al. 2001). Margin sediments exhibit ubiquitous depth zonation (Carney et al. 2005), with a diverse suite of species that occupy restricted bathymetric ranges along any given section of the margin. Major shifts in composition among taxa are observed at the shelf-slope transition zone (canyons <500 m), along the upper slope (1,000 m), and at the lower slope transition zone (<3,000 m) (Gibson et al. 2005). In the deep sea, macrofaunal assemblages are generally limited by the availability of allochthonous organic material (Rowe et al. 1982, Billet et al. 1983, Rex et al. 2005, Smith et al. 2008) where macrofaunal densities usually decline with depth and distance from the shore (Rowe et al. 1982, Houston and Haedrich 1984, Rex et al. 2005). However, canyon fauna can experience enhanced food supply through the resuspension and deposition of organic-rich sediments, delivered by increased current velocities within the confines of the canyon (Rowe 1971, Shepard et al. 1974). As a result, canyons are often reported as sustaining enhanced abundances and biomass compared with nearby open slope habitats at similar depths (Vetter and Dayton 1998, Duineveld et al. 2001, De Leo et al. 2010) as well as enhancing regional (γ) and local (α) biodiversity (Hecker et al. 1983, Vetter and Dayton 1998, De Leo et al. 2010, Vetter et al. 2010). Furthermore, enhanced habitat heterogeneity can also be a major structuring agent of ecological assemblages, promoting beta (β) diversity (McClain and Barry 2010) in canyon environments. Canyon systems have often been described as biodiversity hotspots, especially at mid-slope depths (Levin and Sibuet 2012) where physical processes, characterized by complex patterns in hydrography, promote topographically induced upwelling, enhanced mixing via internal tides, and the focusing of tidal bores (Vetter and Dayton 1998, Cacchione et al. 2002). Additionally, sediment transport and accumulation (García et al. 2008) represent important influential ecological drivers. Factors such as substrata heterogeneity (Levin and Sibuet 2012) and concentration of organic matter (De Leo et al. 2010) have been suggested to explain higher faunal diversity, abundance, and benthic productivity found in canyon systems compared with surrounding areas. Bathymetric patterns of species diversity have been attributed to changes in sediment characteristics (Etter and Grassle 1992), productivity, currents, oxygen, disturbance, and the interplay of biotic effects with depth and latitude (Levin et al. 2001, Carney et al. 2005). Recent studies report on the uniqueness of canyon benthic communities and habitats and the view that no two canyons are alike (Cunha et al. 2011). Certain submarine canyons may maintain 436 characteristic and unique faunas, but more often canyon macrofaunal assemblages show high dominance and locally reduced biodiversity (Rowe 1971, Gage 1997, Curdia et al. 2004, Cun

Baltimore Canyon, Norfolk Canyon↗