Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Data Science in Science”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,642 records · Page 76Linked to original sources
USGS2025

Carbonatite-hosted residual REE deposits

Rare earth elements (REEs) occur in magmatic rocks but are especially enriched in carbonatite and alkaline silicates. If these rocks are chemically weathered, then the REEs may become further enriched within the regolith developed from these rocks. Primary magmatic REE minerals, as well as the various carbonate minerals and apatite, provide the REEs which, under pervasive chemical weathering, are incorporated within low-temperature REE minerals forming within the regolith. Many of these minerals, as well as their textures, are characteristic of this mode of formation. Lateritic conditions of weathering are instrumental in producing a thick, weathered, or regolith, profile, and the roles of sulfide oxidation, fluctuating groundwater tables, and downward mass wasting due to carbonate dissolution are identified as the most important controls on REE enrichment in the regolith.

Book chapter↗
USGS2025

Preface to the focus section on earthquake-induced ground deformation

Ground failure due to earthquake-induced liquefaction, surface fault rupture, and landsliding has caused substantial damage in the past and continues to pose risks to critical infrastructure in the future. The consideration of ground failure is central to engineering analysis and design, ranging from site-specific engineering assessments of ground failure potential to broader regional-scale ground failure assessments of near-real-time earthquake impacts or longer-term portfolio risk. Uncertainties in all aspects of the problem complicate the prediction of earthquake-induced ground failure, including the identification of hazard-susceptible geomaterials, characterizing their spatial extent and physical properties, spatio-temporal variability in groundwater conditions, characterization of earthquake ground motions, assessing ground failure severity, and linking ground failure severity to infrastructure damage and loss.

Seismological Research Letters↗
USGS2025

Pathways for potential exposure to onshore oil and gas wastewater: What we need to know to protect human health

Produced water is a chemically complex waste stream generated during oil and gas development. Roughly four trillion liters were generated onshore in the United States in 2021 (ALL Consulting, 2022, https://www.gwpc.org/wp-content/uploads/2021/09/2021_Produced_Water_Volumes.pdf ). Efforts are underway to expand historic uses of produced water to offset freshwater needs in water-stressed regions, avoid induced seismic activity associated with its disposal, and extract commodities. Understanding the potential exposures from current and proposed produced water uses and management practices can help to inform health-protective practices. This review summarizes what is known about potential human exposure to produced water from onshore oil and gas development in the United States. We synthesize 236 publications to create a conceptual model of potential human exposure that illustrates the current state of scientific inquiry and knowledge. Exposure to produced water can occur following its release to the environment through spills or leaks during its handling and management. Exposure can also arise from authorized releases, including permitted discharges to surface water, crop irrigation, and road treatment. Knowledge gaps include understanding the variable composition and toxicity of produced water released to the environment, the performance of treatment methods, migration pathways through the environment that can result in human exposure, and the significance of the exposures for human and ecosystem health. Reducing these uncertainties may help in realizing the benefits of produced water use while simultaneously protecting human health.

Environmental Health Perspectives↗
USGS2026

Stepovers and beyond: Structural control of The Geysers geothermal system and the broader Clear Lake region

Fault geometry exerts a first-order control on geothermal systems by governing stress localization, fracture development, and permeability, yet in complex fault networks or broader shear zones, the relative influence of individual geometric features is often difficult to resolve. In the northern California Coast Ranges, The Geysers geothermal field is commonly interpreted to occur within a releasing stepover, although no single, clearly defined stepover is identified in published studies. To investigate the structural controls on The Geysers and the broader Clear Lake region, a two-dimensional elastic boundary element model is developed to evaluate spatial patterns of dilational strain associated with progressively more complete fault geometries. Model results show that dilation in the region is not controlled by a single structure but instead reflects the combined effects of multiple interacting fault elements. Three primary controls are identified: (1) opposing bends in the regional strike-slip fault system, including a releasing bend along the Maacama fault; (2) the southern fault tip of the Collayomi fault, which generates a prominent dilational lobe beneath the southern Geysers; and (3) a releasing stepover between the Collayomi fault and the Geyser Peak–Mercuryville–Big Sulphur Creek fault system, inferred to collectively behave as a right-lateral shear zone bounding the western margin of The Geysers. Predicted dilational strain magnitudes are sufficient to localize permeability between faults. These results highlight that incorporating complete fault networks and bedrock geological mapping can enhance geothermal assessments and provide a transferable framework for evaluating structurally controlled permeability in tectonically active regions.

California↗
USGS2025

Evidence for fluid pressurization of fault zones and persistent sensitivity to injection rate beneath the Raton Basin

Subsurface wastewater injection has increased the seismicity rate within the Raton Basin over more than two decades, with the basin-wide injection rate peaked between 2009-2015. To understand the evolution of injection-induced earthquakes, we systematically analyzed 2016-2024 broadband recordings with a machine-learning-based phase picker and constructed a catalog with 95,993 earthquakes (-1≤ M L ≤4.3). We then inverted for full centroid moment tensors (CMT) for 90 M L ≥ 2 events, with a special interest in constraining the non-double-couple components via probabilistic metrics. Both relocations and CMT solutions support basement-rooted normal faults, including graben and half-graben structures. Furthermore, we observe the non-double-couple components that imply elevated pore pressure in the fault zones. An earthquake cluster emerged in the north-central basin in 2023, preceded by ~1-yr of increased injection volume from wells within 15km. Despite a basin-wide decrease in the injection volume, we highlights the persistence of seismicity that remains to sensitive to injection rates within the Raton Basin.

Colorado, New Mexico↗
USGS2026

Core microbiomes as a potential fingerprinting method of Western USA dust sources

Introduction: Changing frequency and intensity of dust emissions impacts ecosystems and human health. Dust carries microbes, nutrients, heavy metals, and other materials that may change environmental biogeochemistry at deposition sites. Identifying dust sources provides key information on where and when mitigation strategies should be employed. However, commonly used geochemical or isotopic tracers are often not capable of distinguishing between geographic regions. Methods: We explored whether soil bacterial communities may provide distinct fingerprints of dust sources in the western United States. We identified bacterial core communities of dust from ten locations monitored by the National Wind Erosion Research Network (NWERN) with varied land use (cropland, rangeland, and playa), and compared communities to location, soil, and regional characteristics. Samples were collected monthly from Modified Wilson and Cooke (MWAC) samplers, composited by season (spring, summer, and fall), and analyzed using 16S rRNA sequencing. Results: We found distinct bacterial core communities that reflected dust source characteristics. In order of importance, precipitation levels ( p = 0.0001), location ( p = 0.0001), soil texture ( p = 0.0001), seasonality ( p = 0.0001), and elevation (p = 0.0002) were correlated with bacterial community composition. Discussion: Distinct bacterial core communities were associated with site characteristics such as biocrusts, playas, and military base proximity. Our results suggest that the use of core microbiomes may offer a fingerprinting method to identify dust source regions.

Colorado, Nevada, New Mexico, North Dakota, Oklaho↗
USGS2025

Hydrogeology of unconsolidated and bedrock aquifers along the Salmon River, including Malone, Franklin County, New York

The U.S. Geological Survey, in cooperation with the New York State Department of Environmental Conservation, investigated the hydrogeology of the unconsolidated and bedrock aquifers along the Salmon River corridor in northern Franklin County, New York. The study area covers roughly 147 square miles and includes the village of Malone and parts of the Towns of Malone, Bellmont, Burke, Constable, Westville, Bangor, Duane, and Franklin, New York. Groundwater is the primary source for water supply within the study area. Eighty-three percent of all residents use public water supplied from two production wells that draw water from a thick, highly productive sand-and-gravel aquifer likely receiving induced infiltration from the Salmon River. Twenty-four percent of the 187 verified domestic wells in the study area outside of the production well service area boundary are screened in typically discontinuous deposits of stratified sand and sand and gravel. Seventy-six percent of the wells are completed in bedrock aquifers including the Potsdam Sandstone, metamorphic rocks, Theresa Formation, and unknown bedrock. Characterizing and understanding potential groundwater resources is critical for protecting the quality of the groundwater. The information in this report may be used to guide delineation of groundwater contributing areas, assess potential threats to aquifers from both point and nonpoint sources, respond to contamination from spills or leaks from underground storage facilities or other sources, and to support assessments for future development of municipal water supplies.

New York↗
USGS2025

Introduction to the special section on improving measurements of earthquake source parameters

Earthquake source parameters such as magnitude, seismic moment, source dimension, stress drop, and radiated energy are fundamental to understanding earthquake physics, and are also key ingredients in earthquake ground‐motion modeling, rupture simulation, and statistical seismology. However, the uncertainties in these parameters estimated from the radiated seismic wavefield are large due to variability in approaches, including site and attenuation characterizations, and so estimates for an individual earthquake made by different studies can vary greatly. Estimating spectral source parameters remains a popular topic, due to a combination of their intrinsic importance and their apparent ease of measurement, but also a controversial one, due to many sources of variability and large uncertainty. The available methods coupled with necessary parameter choices and assumptions in the analysis make it challenging for researchers to apply methods or understand the reliability in results or reported source parameters. This Special Section on Improving Measurements of Earthquake Source Parameters showcasing comparisons between methods and studies seeks to alleviate some of these difficulties to help the community identify the important components and trade‐offs of decomposing recorded seismograms into their source, path, and site components.

Bulletin of the Seismological Society of America↗
USGS2026

Modeling legacy nitrogen transport under instantaneous, steady-state, and transient groundwater flow conditions

In hydrologic settings where groundwater discharge contributes substantially to surface waters, legacy nitrogen in groundwater can confound surface water nitrogen loads estimated exclusively from current terrestrial sources. Additionally, legacy nitrogen in groundwater can contribute to lagged responses to nitrogen management efforts. Some methods of estimating groundwater contributions to surface water nitrogen loads account for legacy nitrogen, while others do not. The resulting differences are rarely quantified. We used a numerical modeling framework to compare three methods of estimating time-varying annual groundwater nitrogen loads to surface water receptors on eastern Long Island, New York. The instantaneous load method used steady-state contributing areas and includes no temporal groundwater lag. The second method used numerical simulations of nitrogen loads under steady-state flow, which captures groundwater transport lags but omits the annual variability in transient hydrologic stresses. The third method numerically simulated both transient groundwater flow and nitrogen transport to explicitly capture the effects of legacy nitrogen in groundwater. Depending on antecedent nitrogen and hydrologic conditions, historical nitrogen loads estimated from the numerical simulations were sometimes similar (<10% difference) and other times substantially different (±100%) from the instantaneous load estimates. Additionally, simulated future surface water nitrogen loads responded asymptotically over several decades following reductions in terrestrial nitrogen sources, further highlighting the effect of groundwater transport lag times. The comparison of the three methods, quantification of historical interannual variability, and prediction of lagged responses to nitrogen source reductions provide important context for decision makers using estimated groundwater nitrogen loads to help evaluate nitrogen management efficacy.

New York↗
USGS2024

Onset of aftershocks: Constraints on the Rate-and-State model

Aftershock rates typically decay with time t after the mainshock according to the Omori–Utsu law, R (t)=K(c+t) −p ⁠ , with parameters K , c , and p . The rate‐and‐state (RS) model, which is currently the most popular physics‐based seismicity model, also predicts an Omori–Utsu decay with p = 1 and a c ‐value that depends on the size of the coseismic stress change. Because the mainshock‐induced stresses strongly vary in space, the c ‐value should vary accordingly. Short‐time aftershock incompleteness (STAI) in earthquake catalogs has prevented a detailed test of this prediction so far, but the newly developed a ‐positive method for reconstructing the true earthquake rate now allows its testing. Using previously published slip models, we calculate the coseismic stress changes for the six largest mainshocks in Southern California in recent decades and estimate the maximum shear as a scalar proxy of the coseismic stress tensor. Aftershock rates reconstructed for events in different stress ranges show that the rates follow a power law with p = 1 independent of stress with no clear sign of a c ‐value. The onset of the power‐law decay is abrupt and more delayed in areas with smaller stress changes. The observations do not necessarily contradict the RS model, as STAI limits the resolution for early aftershocks, and the RS model can reproduce the observations for specific Aσ values. However, the observations lead to strong constraints, namely Aσ <10 kPa and a power‐law decay of the background rate with distance to the fault, with exponent 2.7.

Seismological Research Letters↗
USGS2024

Testing rate‐and‐state predictions of aftershock decay with distance

We analyze aftershocks of the 2019 M 7.1 Ridgecrest mainshock and isolated M 5–6 mainshocks in southern California to test predictions made by the rate‐and‐state friction model of Dieterich (1994) . Rate‐and‐state friction predicts that the seismicity rate after a stress step follows Omori decay, where the Omori c ‐value, which is the saturation in aftershock rate observed at small times, is larger for smaller stress steps. Put in the context of an aftershock sequence, this predicts that the Omori c ‐value will be systematically larger at greater distances from the mainshock. To our knowledge, this predicted effect has not been observed. In part this may be because the Omori c ‐value is difficult to measure because it often reflects short‐term catalog incompleteness rather than a true saturation in aftershock rate. We explore the dependence of the Omori c ‐value on the distance to the mainshock by applying the “ a ‐positive” method ( van der Elst and Page, 2023 ). This method is insensitive to short‐term aftershock incompleteness and allows resolution of the true aftershock rate deep into the mainshock coda. For aftershocks of the Ridgecrest mainshock and stacked M 5–6 mainshocks, we observe systematic differences in early aftershock rates, relative to mainshock distance, consistent with the predictions of rate‐and‐state friction. Furthermore, for the larger Ridgecrest dataset, we observe that aftershocks nearer to the mainshock start earlier, and we resolve a flattening of the Omori curve consistent with a larger Omori c ‐value for the farthest aftershocks, as predicted by Dieterich (1994) .

Seismological Research Letters↗
USGS2026

Light-dependent activity of deepwater sculpin (Myoxocephalus thompsonii) across substrates with and without predation risk

Light availability strongly influences predator–prey interactions in deepwater ecosystems, where visual constraints shape both foraging success and prey behavior. The behavioral response of deepwater sculpin ( Myoxocephalus thompsonii ) to siscowet lake trout ( Salvelinus namaycush siscowet ) was studied under ecologically relevant light intensities spanning several orders of magnitude typical of daytime downwelling light in the 20–100 m depth range of Lake Superior. Trials were conducted over varying substrates (gravel, sand, and black fabric). Deepwater sculpin showed a significant preference for gravel over sand and black fabric. In the absence of siscowet, sculpin movement frequency increased as light intensity decreased. Sculpin reaction distance to siscowet was influenced by both light and substrate. Reaction distance was shortest at low light intensities, peaked at intermediate light intensities (3.05 × 10⁹ to < 6.0 × 10⁹ photons m⁻2 s⁻1), and declined again at the highest light intensities tested. In the presence of siscowet, sculpin activity was suppressed at the upper end of the light range (≥ 6.0 × 10⁹ photons m⁻2 s⁻1). The greatest increase in movement occurred between 6.0 × 10⁹ and 3.05 × 10⁹ photons m⁻2 s⁻1, which corresponded to the range where siscowet prey capture declined, suggesting sculpin exploit this low-light window to move with reduced risk. Reduced activity in the presence of predators is common among cryptic species, and our findings suggest that sculpin restrict movement at higher light levels to avoid detection by siscowet.

Wisconsin↗
USGS2023

Preliminary geologic map of the Southern Santa Rosa Mountains and Borrego Badlands, San Diego County, Southern California

This investigation delineates the geologic framework of an area of 75 square kilometers (km 2 ) located west of the Salton Sea in southern California (fig. 1, on sheet 1). The study area encompasses the south flank of the Santa Rosa Mountains and the eastern part of the Borrego Badlands (sheet 1). In this study area, regionally important stratigraphic and structural elements collectively inform the late Cenozoic geologic evolution of the Anza-Borrego sector of the Salton Trough province. Critical stratigraphic and structural elements in the map area include the following: The well exposed sequence of late Cenozoic, nonmarine sedimentary rocks that filled the Anza-Borrego subbasin (fig. 1) of the Salton Trough; A tectonic boundary that—in the southern Santa Rosa Mountains—separates the sedimentary strata from underlying crystalline rocks of Peninsular Ranges type. This tectonic boundary, named the West Salton Detachment Fault System by Axen and Fletcher (1998), is projected to underlie all late Cenozoic sedimentary strata in the Anza-Borrego subbasin of the Salton Trough; A variety of transpressional, transtensional, and strike-slip structures that have deformed the late Cenozoic sedimentary strata and collectively guided syntectonic and posttectonic depositional events within the Anza-Borrego subbasin of the Salton Trough; and The southeasternmost surface expression of the Clark Fault, a major strand of the dextral San Jacinto Fault Zone. Geologic mapping and analysis for this investigation focused on clarifying geologic relations among these four stratigraphic and structural aspects in the map area.

California↗
USGS2007

Divisions of geologic time—Major chronostratigraphic and geochronologic units

Effective communication in the geosciences requires consistent uses of stratigraphic nomenclature, especially divisions of geologic time. A geologic time scale is composed of standard stratigraphic divisions based on rock sequences and calibrated in years. Over the years, the development of new dating methods and refinement of previous ones have stimulated revisions to geologic time scales. Since the mid-1990s, geologists from the U.S. Geological Survey (USGS), State geological surveys, academia, and other organizations have sought a consistent time scale to be used in communicating ages of geologic units in the United States. Many international debates have occurred over names and boundaries of units, and various time scales have been used by the geoscience community. For consistency purposes, the USGS Geologic Names Committee and the Association of American State Geologists developed Divisions of Geologic Time .

Fact Sheet↗
USGS2026

Groundwater spatial variability within an atoll island: Assessing shallow aquifer heterogeneity with geophysical and physicochemical measurements

This study examines the spatial variability of shallow groundwater on Dhigelaabadhoo Island using electromagnetic induction surveys, groundwater monitoring, and sediment analyses. The research reveals how variations in island morphology—such as differences in elevation, reef flat width, and sediment composition—affect the spatial distribution of groundwater lenses and the overall aquifer dynamics. Saltwater intrusion is especially pronounced in low elevated areas, with narrow reef flat plate and areas where higher hydraulic conductivity—driven by the presence of coarser sediments—is observed, whereas regions characterized by finer sediments, higher elevation, and wider reef flat plates tend to support more symmetric and less saline groundwater lenses. The geophysical investigations reveal that tidal oscillations alter groundwater movement by markedly changing water levels and conductivity, thereby underscoring the critical need to account for temporal dynamics in atoll coastal aquifer systems and the importance of integrating tidal dynamics into the aquifer zone. The findings highlight the significant role of intrinsic morphological and external hydrodynamic factors in shaping groundwater distribution on atoll islands, offering critical insights for sustainable freshwater resource management.

Dhigelaabadhoo Island↗
USGS1998

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic units�an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida↗
USGS1999

Water-quality assessment of south-central Texas — Descriptions and comparisons of nutrients, pesticides, and volatile organic compounds at three intensive fixed sites, 1996-98

Water-quality samples were collected during April 1996-April 1998 at three intensive fixed sites in the San Antonio region of the South-Central Texas study unit as part of the U.S. Geological Survey National Water-Quality Assessment Program. The sampling strategy for the intensive fixed-site assessment is centered on obtaining information about the occurrence and seasonal patterns of selected constituents including nutrients, pesticides, and volatile organic compounds. The three sites selected to determine the effects of agriculture and urbanization on surface-water quality in the study unit are Medina River at LaCoste (agriculture indicator site), Salado Creek (lower station) at San Antonio (urban indicator site), and San Antonio River near Elmendorf (integrator site). Concentrations of two nutrients, dissolved nitrite plus nitrate nitrogen and total phosphorus, were largest at the integrator site, which is downstream of municipal wastewater treatment plants. Nitrite plus nitrate nitrogen concentrations at this site often exceeded the U.S. Environmental Protection Agency (EPA) maximum contaminant level (MCL) for drinking water. All total phosphorus concentrations at the site exceeded the EPA recommended maximum concentration for streams not discharging directly into reservoirs. Nitrite plus nitrate nitrogen concentrations at the integrator site tended to be smaller, and total phosphorus concentrations at the urban site tended to be larger in samples collected during stormflow than during base flow. The most detections and largest concentrations of three pesticides (atrazine, diazinon, and prometon) were in samples collected at the urban site. Some pesticide concentrations at the agriculture site showed a seasonal pattern of increasing concentrations during spring, the peak application season. Four pesticides (atrazine, deethylatrazine, diazinon, and prometon) were detected in at least 38 percent of samples collected at all three sites. The concentrations of all detected pesticides that have an MCL were less than the MCL at the three sites. More volatile organic compounds (VOC) were detected at the urban indicator site than at the agriculture indicator site, mostly likely because more sources are located in urbanized areas. The most VOCs detected and the largest concentrations of two VOCs (chloroform and tetrahydrofuran) were in samples from the integrator site. More VOCs were detected in samples collected at the integrator site during stormflow than during base flow. The concentrations of all detected VOCs that have an MCL were less than the MCL at the three sites.

Texas↗
USGS1976

An environmental assessment of impacts of coal development on the water resources of the Yampa River basin, Colorado and Wyoming; Phase I work plan

Coal resources of the western United States are being developed at ever-increasing rates, causing concerns of the effects of mining and associated activities on the environment. The Yampa River basin in northwestern Colorado and south-central Wyoming is undergoing economic development of its coal, oil and gas, and uranium resources. The Yampa River basin assessment is a 21-year program of the U.S. Geological Survey. It is designed primarily to assess the availability and quality of the basin's water resources. The basin assessment also will evaluate potential environmental and selected socioeconomic impacts of energy-resource development plans proposed by mining and power companies. This report serves as a project work plan for the basin assessment's first-phase work activities. Economic development in the Yampa River basin will result in higher levels of residuals (noneconomic byproducts) being discharged into the environment. Residuals-management encompasses the technological and economic interrelationships that should be considered in order to comply with Federal and State environmental-control regulations regarding air quality, water quality, and disposal of solid wastes. The basin assessment, the first phase that is described by this report, is designed to provide Federal, State, and local decision-makers with the basic environmental information needed to formulate and to evaluate policies for the development of energy resources. The techniques applied and conclusions reached in the Yampa River basin assessment should aid similar studies of other energy-rich basins in the western United States.

Colorado, Wyoming↗