Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Electronics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72Linked to original sources
USGS2024

Methods of analysis—Determination of pesticides in filtered water and suspended sediment using liquid chromatography- and gas chromatography-tandem mass spectrometry

The widespread application of pesticides in agricultural and urban areas leads to their presence in surface waters. Presence of these biologically active chemicals in environmental waters potentially has adverse effects on nontarget organisms. To better understand the environmental fate of these contaminants, a robust method to capture chemicals with wide-ranging physicochemical properties has been developed. The method was developed by the U.S. Geological Survey’s Organic Chemistry Research Laboratory to monitor pesticides, pesticide degradates, and other agrochemicals in environmental surface waters throughout the country. The analysis involves a multiresidue method to determine 183 pesticides and pesticide degradates in filtered water samples and 178 pesticides and pesticide degradates in paired suspended sediment samples. After the filtration of whole water, contaminants are individually measured in the filtered water and the collected suspended sediment. Filtered water is extracted via solid-phase extraction, whereas suspended sediment is extracted using an ultrasonication, solid-liquid extraction. Samples are analyzed by liquid chromatography-tandem mass spectrometry using an electrospray ionization source in positive and negative modes and analyzed by gas chromatography-tandem mass spectrometry using an advanced electron ionization source in positive mode. Instrument parameters were optimized for the highest sensitivity, and at least two transitions (quantifier and qualifier) were monitored for each analyte. Recoveries in test filtered water ( n =9; 183 analytes) from the American River, California, and suspended sediment ( n =9; 178 analytes) samples fortified at 15 nanograms per liter (ng/L) ranged from 70.1 to 121.0 and 71.1 to 117.0 percent in water and suspended sediment filter samples, respectively. Method detection limits of pesticides and pesticide degradates ranged from 0.5 to 10.6 ng/L in water and 0.7 to 11.8 ng/L in suspended sediment filters. Reporting limits were 1.1–21.1 ng/L and 1.5–23.7 ng/L in water and filter samples, respectively. The developed method is applied to surface-water samples for the analysis of pesticides, pesticide degradates, and other agrochemicals.

Techniques and Methods↗
USGS1990

Borehole geophysics applied to ground-water investigations

The purpose of this manual is to provide hydrologists, geologists, and others who have the necessary background in hydrogeology with the basic information needed to apply the most useful borehole-geophysical-logging techniques to the solution of problems in ground-water hydrology. Geophysical logs can provide information on the construction of wells and on the character of the rocks and fluids penetrated by those wells, as well as on changes in the character of these factors over time. The response of well logs is caused by petrophysical factors, by the quality, temperature, and pressure of interstitial fluids, and by ground-water flow. Qualitative and quantitative analysis of analog records and computer analysis of digitized logs are used to derive geohydrologic information. This information can then be extrapolated vertically within a well and laterally to other wells using logs. The physical principles by which the mechanical and electronic components of a logging system measure properties of rocks, fluids, and wells, as well as the principles of measurement, must be understood if geophysical logs are to be interpreted correctly. Plating a logging operation involves selecting the equipment and the logs most likely to provide the needed information. Information on well construction and geohydrology is needed to guide this selection. Quality control of logs is an important responsibility of both the equipment operator and the log analyst and requires both calibration and well-site standardization of equipment. Logging techniques that are widely used in ground-water hydrology or that have significant potential for application to this field include spontaneous potential, resistance, resistivity, gamma, gamma spectrometry, gamma-gamma, neutron, acoustic velocity, acoustic televiewer, caliper, and fluid temperature, conductivity, and flow. The following topics are discussed for each of these techniques: principles and instrumentation, calibration and standardization, volume of investigation, extraneous effects, and interpretation and applications.

Techniques of Water-Resources Investigations↗
USGS1985

Acoustic velocity meter systems

Acoustic velocity meter (AVM) systems operate on the principles that the point-to-point upstream traveltime of an acoustic pulse is longer than the downstream traveltime and that this difference in traveltime can be accurately measured by electronic devices. An AVM system is capable of recording water velocity (and discharge) under a wide range of conditions, but some constraints apply: 1. Accuracy is reduced and performance is degraded if the acoustic path is not a continuous straight line. The path can be bent by reflection if it is too close to a stream boundary or by refraction if it passes through density gradients resulting from variations in either water temperature or salinity. For paths of less than 100 m, a temperature gradient of 0.1' per meter causes signal bending less than 0.6 meter at midchannel, and satisfactory velocity results can be obtained. Reflection from stream boundaries can cause signal cancellation if boundaries are too close to signal path. 2. Signal strength is attenuated by particles or bubbles that absorb, spread, or scatter sound. The concentration of particles or bubbles that can be tolerated is a function of the path length and frequency of the acoustic signal. 3. Changes in streamline orientation can affect system accuracy if the variability is random. 4. Errors relating to signal resolution are much larger for a single threshold detection scheme than for multiple threshold schemes. This report provides methods for computing the effect of various conditions on the accuracy of a record obtained from an AVM. The equipment must be adapted to the site. Field reconnaissance and preinstallation analysis to detect possible problems are critical for proper installation and operation of an AVM system.

Techniques of Water-Resources Investigations↗
USGS2004

Use of submersible pressure transducers in water-resources investigations

Submersible pressure transducers, developed in the early 1960s, have made the collection of water-level and pressure data much more convenient than former methods. Submersible pressure transducers, when combined with electronic data recorders have made it possible to collect continuous or nearly continuous water-level or pressure data from wells, piezometers, soil-moisture tensiometers, and surface water gages. These more frequent measurements have led to an improved understanding of the hydraulic processes in streams, soils, and aquifers. This manual describes the operational theory behind submersible pressure transducers and provides information about their use in hydrologic investigations conducted by the U.S. Geological Survey.

Techniques of Water-Resources Investigations↗
USGS2005

Preparations for water sampling

The National Field Manual for the Collection of Water-Quality Data (National Field Manual) provides guidelines and standard procedures for U.S. Geological Survey (USGS) personnel who collect data used to assess the quality of the Nation’s surface-water and ground-water resources. This chapter addresses field-trip preparations, including selection of sample-collection sites for studies of surface-water quality, site reconnaissance and well selection for studies of groundwater quality, and the establishment of electronic files and field files and folders for a sampling site. Each chapter of the National Field Manual is published separately and revised periodically. Newly published and revised chapters are posted on the World Wide Web on the USGS page "National Field Manual for the Collection of Water-Quality Data." The URL for this page is http://pubs.water.usgs.gov/twri9A/ (accessed Jan. 31, 2005).

Techniques of Water-Resources Investigations↗
USGS2012

Chapter A6. Section 6.8. Use of multiparameter instruments for routine field measurements

The miniaturization of sensors and other technological advances in electronics have resulted in water-quality instruments that house multiple sensors capable of simultaneous readings for various field measurements in environmental waters. With the use of these multiparameter instruments, field measurements can be determined with considerable reduction in the field work that generally is required when using multiple single-parameter instruments. This section addresses the short-term or discrete-measurement use of portable multiparameter instruments. Each chapter of the National Field Manual is published separately and revised periodically. Newly published and revised chapters will be announced on the USGS Home Page on the World Wide Web under 'New Publications of the U.S. Geological Survey.'

Techniques of Water-Resources Investigations↗
USGS2000

Analysis of nitrate and volatile organic compound data for ground water in the Great Salt Lake Basins, Utah, Idaho, and Wyoming, 1980-98

In 1995, ground water was the source of drinking water to about 52 percent of the population served by public drinking water systems in the Great Salt Lake Basins study unit, which includes parts of Utah, Idaho, and Wyoming. Existing nitrate and volatile organic compound data for ground water collected in the study unit were compiled and summarized as part of the National Water-Quality Assessment Program’s objective to describe water-quality conditions in the Nation’s aquifers. Prerequisites for the inclusion of nitrate and volatile organic compound data into this retrospective analysis are that the data set is available in electronic form, the data were collected during 1980-98, the data set is somewhat regional in coverage, and the locations of the sampled sites are known. Ground-water data stored in the U.S. Geological Survey’s National Water Information System and the Idaho and Utah Public Drinking Water Systems databases were reviewed. Only the most recent analysis was included in the data sets if more than one analysis was available for a site. The National Water Information System data set contained nitrate analyses for water from 480 wells. The median concentration of nitrate was 1.30 milligrams per liter for the 388 values above minimum reporting limits. The maximum contaminant level for nitrate as established by the U.S. Environmental Protection Agency was exceeded in water from 10 of the 200 wells less than or equal to 150 feet deep and in water from 3 of 280 wells greater than 150 feet deep. The Public Drinking Water Systems data set contained nitrate analyses for water from 587 wells. The median concentration of nitrate was 1.12 milligrams per liter for the 548 values above minimum reporting limits. The maximum contaminant level for nitrate was exceeded at 1 site and 22 sites had concentrations equal to or greater than 5 milligrams per liter. The types of land use surrounding a well and the well depth were related to measured nitrate concentrations in the sampled ground water. Overall, water sampled from wells in rangeland areas had a lower median measured nitrate concentration (0.76 milligrams per liter) than water from areas with an agricultural or urban/residential land use (1.41 and 1.20 milligrams per liter, respectively). In the National Water Information System data set, the median measured nitrate concentration in water from urban/residential areas varied from 1.00 milligrams per liter for wells greater than 150 feet deep to 1.84 milligrams per liter for wells less than or equal to 150 feet deep. The Public Drinking Water Systems and the National Water Information System data sets contained analyses for most of the State and Federally regulated volatile organic compounds in water from about 368 and 74 wells, respectively. Fifteen different volatile organic compounds were detected at least once in ground water sampled from the Great Salt Lake Basins study unit. Water from 21 wells contained at least 1 volatile organic compound at detectable concentrations. About 68 percent of the volatile organic compounds detected were in water sampled from wells in Salt Lake County, Utah. Tetrachloroethylene was the most commonly detected volatile organic compound in ground water sampled from the study unit, present in 8 out of 442 samples. Maximum contaminant levels for tetrachloroethylene and 1,1-dichloroethylene as established by the U.S. Environmental Protection Agency were exceeded in water from one well each.

Idaho,Utah, Wyoming↗
USGS2002

Aquifer geochemistry and effects of pumping on ground-water quality at the Green Belt Parkway Well Field, Holbrook, Long Island, New York

Geochemistry, microbiology, and water quality of the Magothy aquifer at a new supply well in Holbrook were studied to help identify factors that contribute to iron-related biofouling of public-supply wells. The organic carbon content of borehole sediments from the screen zone, and the dominant terminal electron-accepting processes (TEAPs), varied by depth. TEAP assays of core sediments indicated that iron reduction, sulfate reduction, and undetermined (possibly oxic) reactions and microbial activity are correlated with organic carbon (lignite) content. The quality of water from this well, therefore, reflects the wide range of aquifer microenvironments at this site. High concentrations of dissolved iron (3.6 to 6.4 micromoles per liter) in water samples from this well indicate that some water is derived from Fe(III)-reducing sediments within the aquifer, but traces of dissolved oxygen indicate inflow of shallow, oxygenated water from shallow units that overlie the local confining units. Water-quality monitoring before and during a 2-day pumping test indicates that continuous pumping from the Magothy aquifer at this site can induce downward flow of shallow, oxygenated water despite the locally confined conditions. Average concentrations of dissolved oxygen are high (5.2 milligrams per liter, or mg/L) in the overlying upper glacial aquifer and at the top of the Magothy aquifer (4.3 mg/L), and low ( < 0.1 mg/L) in the deeper, anaerobic part of the Magothy; average concentrations of phosphate are high (0.4 mg/L) in the upper glacial aquifer and lower (0.008 mg/L) at the top of the Magothy aquifer and in the deeper part of the Magothy (0.013 mg/L). Concentrations of both constituents increased during the 2 days of pumping. The δ 34 S of sulfate in shallow ground water from observation wells (3.8 to 6.4 per mil) was much heavier than that in the supplywell water (-0.1 per mil) and was used to help identify sources of water entering the supply well. The δ 34 S of sulfate in a deep observation well adjacent to the supply well increased from 2.4 per mil before pumping to 3.3 per mil after pumping; this confirms that the pumping induced downward migration of water. The lighter δ 34 S value in the pumped water than in the adjacent observation well probably indicates FeS 2 oxidation (which releases light δ 34 S in adjacent sediments) by the downward flow of oxygenated water.

New York↗
USGS2001

Biodegradation potential of chlorinated solvents in ground water at the Naval Surface Warfare Center, Louisville, Kentucky, July 1999 to February 2000

The U.S. Geological Survey, in cooperation with the U.S. Department of the Navy, Southern Division Naval Facilities Engineering Command, investigated the potential for biodegradation of chlorinated solvents in ground water at the Naval Surface Warfare Center (also known as the Naval Ordnance Station, or the station), Louisville, Kentucky. The subsurface down to at least 100 feet at the station is characterized, from shallowest to deepest, by overburden deposits, a shale layer, and limestone. In general, all of the strata are poorly permeable. The permeable zones of the overburden and the limestone make up the overburden aquifer and the bedrock aquifer, respectively. Observed concentrations of redox-sensitive solutes suggest that the predominant anaerobic terminal electron accepting process in the overburden aquifer can shift between iron reduction and sulfate reduction, possibly as a result of rainfall-induced oxidation events. Daughter-product concentrations and laboratory experiments indicate that a variety of mechanisms, including reductive dechlorination and cometabolic oxidation, appear to be actively

Kentucky↗
USGS2002

Occurrence and transport of diazinon in the Sacramento River, California, and selected tributaries during three winter storms, January-February 2000

The organophosphate pesticide diazinon is applied as a dormant orchard spray in the Sacramento Valley, California, during the winter when the area receives a majority of its annual rainfall. Dormant spray pesticides, thus, have the potential to wash off the areas of application and migrate with storm runoff to streams in the Sacramento River Basin. Previous monitoring studies have shown that rain and associated runoff from winter storms plays an important role in the transport of diazinon from point of application to the Sacramento River and tributaries. Between January 30 and February 25, 2000, diazinon concentrations in the Sacramento River and selected tributaries were monitored on 5 consecutive days during each of three winter storms that moved through the Sacramento Valley after diazinon had been applied to orchards in the basin. Water samples were collected at 17 sites chosen to represent the effect of upstream land use at local and regional scales. Most samples were analyzed using an enzyme-linked immunosorbent assay (ELISA). Analysis by gas chromatography with electron capture detector and thermionic specific detector (GC/ECD/TSD) and gas chromatography with mass spectrometry (GC/MS) was done on split replicates from over 30 percent of the samples to confirm ELISA results and to provide lower analytical reporting limits at selected sites [30 ng/L (nanogram per liter) for ELISA, 20 ng/L for GC/ECD/TSD, and 2 ng/L for GC/MS]. Concentrations determined from ELISA analyses were consistently higher than concentrations for split samples analyzed by gas chromatography methods. Because of bias between diazinon concentrations using ELISA and gas chromatography methods, results from ELISA analyses were not compared to water-quality criteria. Load calculations using the ELISA analyses are similarly biased. Because the bias was consistent, however, the ELISA data is useful in site-to-site comparisons used to rank the relative levels and contributions of diazinon from individual subbasins in the watershed. Concentrations of diazinon in 138 samples analyzed by gas chromatography methods ranged from below detection (2 ng/L) to 2,890 ng/L with a median of 44 ng/L. Thirty percent of the samples had concentrations greater than 80 ng/L, which is considered by California as the criterion maximum concentration for the protection of aquatic habitat. Concentrations were highest in small tributaries and canals draining subbasins with predominantly agricultural land use and in a channel draining the Yuba City urban area. Load estimates using concentrations derived from GC/MS analyses indicate that about 30 percent of the diazinon in the lower Sacramento River is from the Feather River Basin. Loads estimated using ELISA analyses show a similar, but slightly higher fraction of the total load coming from that basin. The source of over half the total load measured at Sacramento River at Alamar appears to have originated in the part of the drainage basin upstream of the city of Colusa. Of the diazinon reported applied to agricultural land in Sacramento Valley (about 42,500 pounds active ingredient) just before and during the monitoring period, about 0.4 percent appeared to be transported to the lower Sacramento River during the period of monitoring. A similar percent of applied diazinon was estimated to have entered the Feather River from upstream sources. Diazinon use in the study area during the 1999-2000 dormant spray season was unusually low, about 60 percent of the average of the previous 4 years. Therefore, diazinon loadings may be higher in subsequent years, should use increase and pesticide management practices remain the same. Although diazinon was the most frequently detected pesticide and the pesticide detected at the highest concentrations, 10 other pesticides were detected in the samples collected. These included the insecticides methidathion and chlorpyrifos, and the herbicides simazine, molinate and thiobencarb.

California↗
USGS2003

Questa baseline and pre-mining ground-water quality investigation. 3. Historical ground-water quality for the Red River Valley, New Mexico

Historical ground-water quality data for 100 wells in the Red River Valley between the U.S. Geological Survey streamflow-gaging station (08265000), near Questa, and Placer Creek east of the town of Red River, New Mexico, were compiled and reviewed. The tabulation included 608 water-quality records from 23 sources entered into an electronic database. Groundwater quality data were first collected at the Red River wastewater-treatment facility in 1982. Most analyses, however, were obtained between 1994 and 2002, even though the first wells were developed in 1962. The data were evaluated by considering (a) temporal consistency, (b) quality of sampling methods, (c) charge imbalance, and (d) replicate analyses. Analyses that qualified on the basis of these criteria were modeled to obtain saturation indices for gypsum, calcite, fluorite, gibbsite, manganite, and rhodocrosite. Plots created from the data illustrate that water chemistry in the Red River Valley is predominantly controlled by calcite dissolution, congruent gypsum dissolution, and pyrite oxidation.

New Mexico↗
USGS1978

Inflatable straddle packers and associated equipment for hydraulic fracturing and hydrologic testing

Independent aquifer testing is the only way to fully understand the hydrology encountered in boreholes intersecting multiple aquifers. The most feasible method to accomplish the testing of multiple aquifer wells is through the use inflatable packers. The straddle packers and associated equipment herein described arE valuable tools for making isolated aquifer tests as well as conducting hydraulic fracturing experiments. The system, due to design, permits multiple tests in a bore-hole without the necessity of tripping in and out of the hole to redress the packers prior to testing each zone. Electronic pressure transducers, the output of which was fed into strip-chart recorders, were used to monitor the zone being tested, as well as to monitor the zones above and below the packers. This was necessary to ensure that no leaking had occurred around the packers, causing hydraulic continuity between the isolated zones.

Water-Resources Investigations Report↗
USGS1979

Evaluation of methods for estimating ground-water withdrawals in western Kansas

During 1978, methods of estimating ground-water withdrawals in western Kansas were examined and evaluated, using both existing data from the files of the U.S. Geological Survey and newly collected data. Values for annual ground-water withdrawals reported to the Division of Water Resources, Kansas State Board of Agriculture, by water users probably contain substantial errors because most individual users do not possess the means to measure or accurately estimate the discharge rates of their wells. Such reported values are estimated to average 10 to 15 percent higher than the actual discharge rate. Values obtained from discharge-totaling meters are reasonably accurate, but few wells are equipped with these meters, and the cost of equipping all wells with meters may be prohibitive. Measured rates of power consumption can give good estimates of total withdrawal from wells where the power consumption is measured. However, power-consumption values cannot be extrapolated reliably from one well to another. Three techniques are regarded as promising for estimating areal ground-water withdrawals from readily collected data: Examination of a small sample of withdrawal values from metered wells indicates that the statistical approach used by Luckey (1972) may be applied to western Kansas to estimate total withdrawal with acceptable accuracy in a large area from a statistical sample of measured values. Measured values of irrigation application at a small number of selected wells might be used to compute total withdrawal for irrigation by crop type and precipitation zone. Evaluation of reported values of irrigation-water application for selected crops in zones of generally similar precipitation showed that, although the reported values are judged to be erroneously high, the reported values were consistent with each other and with average precipitation. Power-consumption coefficients may be used to calculate an average coefficient for an area. The method described by Luckey (1972) was used to calculate the number of power-consumption coefficients that would have to be determined to estimate the mean power consumption of wells pumped by electric or natural-gas engines. The results indicate that as few as 100 values would produce results accurate to within 10 percent of the true average at the 95-percent confidence level. Thus, power coefficients for a particular type of irrigation system in any given area can be used even though values of power coefficients have little transfer value from well to well. Efforts by the Instrument Development Laboratofy of the U.S. Geological Survey to design improved instruments for measuring ground-water withdrawals have produced two promising results: An electronic running-time meter (Running-time Sentry) that was tested during 1978 in western Kansas and Florida appears to give accurate values of total pumping time. Large-scale testing of this prototype running-time meter is planned for 1979. A low-cost discharge-totaling meter (REELTOT), based on the concept of sensing the velocity head in a pipe with differential-pressure transducers permanently installed in the pipe, is nearly complete. Early prototypes of this instrument may be tested in western Kansas during 1979. For the remainder of this study, the three techniques for estimating areal ground-water withdrawals described above will be tested on a larger scale in Groundwater Management District No. 1, an area of about 1,800 square miles in west-central Kansas. About 150 randomly selected wells will be equipped with Running-time Sentry units and monitored for total withdrawal, instantaneous discharge, and power consumption. A few wells will be equipped with prototype discharge-totaling meters. The performance of the Sentry units and discharge-totaling meters will be evaluated. Areal estimates of withdrawal from measured withdrawal values, from average power-consumption coefficients, and from irrigation application by crop will be calculated and compared with each other and with reported values of withdrawal.

Kansas↗
USGS1996

Evaluation of Acoustic Doppler Current Profiler measurements of river discharge

Developments in Acoustic Doppler Current Profiler (ADCP) technologies have made these instruments potentially useful for making measurements of discharge in rivers and large streams. Although there have been several laboratory studies and some field experiments, quantitative information on the performance of ADCP's under field conditions is relatively rare but essential to proper assessment of the potential uses and limitations of these instruments. This study was a comparative evaluation of river discharge data and ADCP data collected with conventional methods at 12 selected U.S. Geological Survey streamflow- gaging stations in the continental United States. ADCP discharge measurements were made at the 12 sites in 1994. Twenty-six of the 31 measurements differed by less than 5 percent from the discharges determined with conventional methods. All 31 ADCP measurements were within 8 percent of the conventional method discharges. The standard deviations of the ADCP measurements ranged from approximately 1 to 6 percent and were generally higher than the measurement errors predicted by error-propagation analysis of ADCP instrument performance. These error-prediction methods assume that the largest component of ADCP discharge measurement error is instrument related. The larger standard deviations indicate that substantial portions of measurement error may be attributable to sources unrelated to ADCP electronics or signal processing and are functions of the field environment.

Water-Resources Investigations Report↗
USGS1997

Guidelines and standard procedures for studies of ground-water quality; selection and installation of wells, and supporting documentation

This is the first of a two-part report to document guidelines and standard procedures of the U.S. Geological Survey for the acquisition of data in ground-water-quality studies. This report provides guidelines and procedures for the selection and installation of wells for water-quality studies/*, and the required or recommended supporting documentation of these activities. Topics include (1) documentation needed for well files, field folders, and electronic files; (2) criteria and information needed for the selection of water-supply and observation wells, including site inventory and data collection during field reconnaissance; and (3) criteria and preparation for installation of monitoring wells, including the effects of equipment and materials on the chemistry of ground-water samples, a summary of drilling and coring methods, and information concerning well completion, development, and disposition.

Water-Resources Investigations Report↗
USGS1998

Lithology and fracture characterization from drilling investigations in the Mirror Lake area, Grafton County, New Hampshire

The lithology and fracture network of the bedrock aquifer in the Mirror Lake area were characterized from hydrogeologic data collected from 1979-95 in Grafton County, N.H. The collection of these data is an integral part of an ongoing multidisciplinary study by the U.S. Geological Survey to characterize groundwater flow and solute transport in fractured rock. The data provide a physical framework and enable the characterization of the fractures and the rock types in the bedrock aquifer in the Mirror Lake study area. In addition, these data provide a detailed description of the subsurface intersected by boreholes that can be used to compare the results of other borehole testing. The Mirror Lake area is characterized by steep bedrock uplands that are mostly covered by colluvium, discontinuous stratified-drift deposits, and glacial till that varies locally in thickness from less than 10 meters to as much as 50 meters. The land-surface altitude ranges from 180 meters near the Pemigewasset River to 720 meters on the mountain top on the northwestern side of the study area. The bedrock in the area is predominantly sillimanite-grade pelitic schists that have been complexly folded and intruded by granitoids, pegmatites, and diabase dikes. The bedrock has been fractured in response to local and tectonic stress. The resulting interconnected network of fractures forms the bedrock aquifer. This report describes the lithologic units in the study area and provides a characterization of the lithology and fractures found in 40 boreholes, which range in depth from 60 to 305 meters, that were drilled for this study. Drilling logs and color video surveys were used to locate and characterize the fractures and rock types in the subsurface. Solid bedrock core was obtained from three of the boreholes. Petrographic thin-section, x-ray diffraction and scanning electron microscope with energy dispersive x-ray fluorescence spectrometry analyses were done on selected samples from boreholes and outcrops. Observations recorded at the time of drilling, descriptions of rock samples collected from the boreholes, interpretation of rock type and fractures based on boreholeimaging surveys, descriptions of rock core and petrographic analyses of selected rock samples are in tables and figures. Analysis of the data provided information on the distribution of fractures and lithology in the boreholes at Mirror Lake. The relative abundances of the rock types were computed for three groups of boreholes, including (1) the Forest Service Experimental (FSE) well field, (2) the Camp Osceola (CO) well field, and (3) the index boreholes, which are 15 boreholes distributed areally throughout the study area including the deepest borehole from each of the two well fields. The index boreholes are separated by hundreds of meters and are typically 100 meters deep. The FSE well field includes 13 boreholes that are separated by 10 to 40 meters. These 13 boreholes are approximately 100 meters deep, except for one borehole that is 230 meters deep. The rocks penetrated by the FSE wells are predominantly igneous. Approximately 70 percent of the rocks encountered in the boreholes in the FSE well field were granite, pegmatite, and aplite. The CO well field includes 9 boreholes that range from 60-70 meters deep and one borehole that is 175 meters deep. The rocks encountered in these boreholes were predominantly metamorphic. The distribution of rock types in the CO well field is similar to the distribution of rocks in highway roadcuts, that are approximately 90 to 150 meters east of the well field. Seventy percent of the roadcut exposures are schist. Collectively, in the 15 index boreholes, the metamorphic and igneous rocks are equally distributed. Analysis of the rock types in these boreholes indicates that the rock types tend to "change" every 5 to 9 meters. Although the metamorphic and igneous rocks each comprise approximately 50 percent of the rock types observed in the 15 index boreholes, 73 percent of the fractures were in the igneous rocks. This indicates that the granitoids tend to be more fractured than the metamorphic rocks. Pegmatite, diabase, quartzite, and gneissic rocks are relatively unfractured. Boreholes completed in bedrock generally have one or two water-bearing zones, which were identified during the drilling process. At the completion of drilling a borehole, the driller estimated the yield of the borehole with an air-lift test. Yields estimated by drillers ranged from less than 3 to 378 liters per minute. These yields are typical of the yields measured for domestic wells in Grafton County. Water levels measured in the open boreholes after the boreholes recovered from the hydraulic stresses of drilling were usually in the steel casing and were within 10 meters of the land surface. Water levels in eight of the boreholes were above the top of casing or above land surface.

New Hampshire↗
USGS1999

Development of a 14-digit Hydrologic Unit Code Numbering System for South Carolina

A Hydrologic Unit Map showing the cataloging units, watersheds, and subwatersheds of South Carolina has been developed by the U.S. Geological Survey in cooperation with the South Carolina Department of Health and Environmental Control, funded through a U.S. Environmental Protection Agency 319 Grant, and the U.S. Department of Agriculture, Natural Resources Conservation Service. These delineations represent 8-, 11-, and 14-digit Hydrologic Unit Codes, respectively. This map presents information on drainage, hydrography, and hydrologic boundaries of the water-resources regions, subregions, accounting units, cataloging units, watersheds, and subwatersheds. The source maps for the basin delineations are 1:24,000-scale 7.5-minute series topographic maps and the base maps are from 1:100,000-scale Digital Line Graphs; however, the data are published at a scale of 1:500,000. In addition, an electronic version of the data is provided on a compact disc. Of the 1,022 subwatersheds delineated for this project, 1,004 range in size from 3,000 to 40,000 acres (4.69 to 62.5 square miles). Seventeen subwatersheds are smaller than 3,000 acres and one subwatershed, located on St. Helena Island, is larger than 40,000 acres. This map and its associated codes provide a standardized base for use by water-resource managers and planners in locating, storing, retrieving, and exchanging hydrologic data. In addition, the map can be used for cataloging water-data acquisition activities, geographically organizing hydrologic data, and planning and describing water-use and related land-use activities.

South Carolina↗
USGS1999

Ground-water contamination by crude oil: Section B in U.S. Geological Survey Toxic Substances Hydrology Program: Proceedings of the technical meeting, Charleston, South Carolina, March 8-12, 1999: Volume 3 (Part C)

Ground water contamination by crude oil, and other petroleum-based liquids, is a widespread problem. An average of 83 crude-oil spills occurred per year during 1994-96 in the United States, each spilling an average of about 50,000 barrels of crude oil (U.S. Office of Pipeline Safety, electronic commun., 1997). An understanding of the fate of organic contaminants (such as oil and gasoline) in the subsurface is needed to design innovative and cost-effective remedial solutions at contaminated sites.

Water-Resources Investigations Report↗