Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Water Investigation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69Linked to original sources
USGS1997

Comparison of the 2-, 25-, and 100-year recurrence interval floods computed from observed data with the 1995 urban flood-frequency estimating equations for Georgia

Flood-frequency relations were computed for 28 urban stations, for 2-, 25-, and 100-year recurrence interval floods and the computations were compared to corresponding recurrence interval floods computed from the estimating equations from a 1995 investigation. Two stations were excluded from further comparisons or analyses because neither station had a significant flood during the period of observed record. The comparisons, based on the student's t-test statistics at the 0.05 level of significance, indicate that the mean residuals of the 25- and 100-year floods were negatively biased by 26.2 percent and 31.6 percent, respectively, at the 26 stations. However, the mean residuals of the 2-year floods were 2.5 percent lower than the mean of the 2-year floods computed from the equations, and were not significantly biased. The reason for this negative bias is that the period of observed record at the 26 stations was a relatively dry period. At 25 of the 26 stations, the two highest simulated peaks used to develop the estimating equations occurred many years before the observed record began. However, no attempt was made to adjust the estimating equations because higher peaks could occur after the period of observed record and an adjustment to the equations would cause an underestimation of design floods.

Georgia↗
USGS1999

Hydrogeology of the unsaturated zone, North Ramp area of the Exploratory Studies Facility, Yucca Mountain, Nevada

Yucca Mountain, in southern Nevada, is being investigated by the U.S. Department of Energy as a potential site for a repository for high-level radioactive waste. This report documents the results of surface-based geologic, pneumatic, hydrologic, and geochemical studies conducted during 1992 to 1996 by the U.S. Geological Survey in the vicinity of the North Ramp of the Exploratory Studies Facility (ESF) that are pertinent to understanding multiphase fluid flow within the deep unsaturated zone. Detailed stratigraphic and structural characteristics of the study area provided the hydrogeologic framework for these investigations. Multiple lines of evidence indicate that gas flow and liquid flow within the welded tuffs of the unsaturated zone occur primarily through fractures. Fracture densities are highest in the Tiva Canyon welded (TCw) and Topopah Spring welded (TSw) hydrogeologic units. Although fracture density is much lower in the intervening nonwelded and bedded tuffs of the Paintbrush nonwelded hydrogeologic unit (PTn), pneumatic and aqueous-phase isotopic evidence indicates that substantial secondary permeability is present locally in the PTn, especially in the vicinity of faults. Borehole air-injection tests indicate that bulk air-permeability ranges from 3.5x10 -14 to 5.4x10 -11 square meters for the welded tuffs and from 1.2x10 -13 to 3.0x10 -12 square meters for the non welded and bedded tuffs of the PTn. Analyses of in-situ pneumatic-pressure data from monitored boreholes produced estimates of bulk permeability that were comparable to those determined from the air-injection tests. In many cases, both sets of estimates are two to three orders of magnitude larger than estimates based on laboratory analyses of unfractured core samples. The in-situ pneumatic-pressure records also indicate that the unsaturated-zone pneumatic system consists of four subsystems that coincide with the four major hydrogeologic units of the unsaturated zone at Yucca Mountain. In descending order, these hydrogeologic units are the Tiva Canyon welded (TCw), Paintbrush nonwelded (PTn), Topopah Spring welded (TSw ), and Calico Hills nonwelded (CHn). Deep percolation takes place as episodic pulses of inflow that propagate rapidly to depth and apparently bypass most of the rock matrix. Field-scale and core-scale water potentials throughout much of the PTn and TSw are very high, generally greater than -0.3 megapascals, and are nearly depth invariant. Thus, the imbibition capacity of the densely welded tuffs, at least near fractures, is very small because of low matrix permeabilities and low water-potential gradients across the fracture-matrix interface. The combination of high fracture permeability, high water potentials, high matrix saturations, and low matrix permeabilities results in a percolation environment that favors deep fracture flow. The episodic pulses of inflow are evidenced in the sporadic but nevertheless commonplace occurrence of water with concentrations of radioactive isotopes indicative of origins postdating the atmospheric testing of nuclear weapons. High concentrations of tritium have been detected at many horizons within the PTn and in the top of the TSw. Much lower concentrations of tritium, indicating the mixing of a bomb-pulse component with older water, have been detected in the deeper sections of the TSw and in the CHn. Evidence for fracture flow also is apparent in the widespread occurrence of perched water with chemical and isotopic signatures that indicate a fracture-flow origin for at least some of this water. In the North Ramp area, perched water has been detected at the base of the Topopah Spring Tuff or in the top of the underlying non welded to partially welded tuffs of the Calico Hills Formation in every dry-drilled borehole of sufficient depth to penetrate the Topopah Spring Tuff-Calico Hills Formation contact. The concentrations of the major ions of the perched water are similar to that of TSw pore water at borehole UZ-14, CHn pore water, and saturated-zone water at boreholes NRG-7 a and SD-9. The absolute chloride concentration of the perched water, however, is much lower than the chloride concentration of pore water from either the PTn or the TSw. The chemical and isotopic compositions of perched water indicate that this water was derived primarily from fracture flow, with little or no contribution from water in the matrix of the overlying rock. Carbon-14 ages of perched water range from 3,000 to 7,000 years. Strontium-87 isotope ratios indicate dissolution of surficial pedogenic calcite and calcite fracture fillings, which supports a fracture-flow origin for perched water. Moreover, carbon-13 and deuterium isotope values indicate rapid infiltration into fractures with little or no prior evaporation. Evidence for deep fracture flow into the Calico Hills Formation at UZ-14 is indicated by carbon-14 values that are from 65 and 95 percent modem carbon, equivalent to apparent ages of about 3,500 to 500 years. Some of these ages are younger than age estimates for perched water in the overlying Topopah Spring Tuff and are much younger than any that could be derived from a matrix-flow model. Evidence is lacking for extensive lateral flow within the PTn or for interception and diversion of this flow downward along structural pathways (faults), two key features of the original conceptual model for unsaturated flow at Yucca Mountain. Where data are available to infer lateral flow in the PTn, it is not certain that fracture flow could not have produced the same results. Pneumatic data, derived primarily from analysis of the interference effects from excavation of the North Ramp tunnel, indicate that faults within the Topopah Spring Tuff are open over substantial distances and are very permeable. Tunnel-boring-induced pneumatic disturbances have been propagated along these faults over distances that exceed 500 meters. These disturbances also have been detected in the pneumatic-pressure record of the overlying PTn in the vicinity of these faults. In spite of the apparent high permeability of faults, the existing data have neither confirmed nor refuted the hypothetical role of these faults in intercepting lateral flow from within or from above the PTn and diverting this flow downward into the deeper subsurface. On the basis of measured temperature gradients within the TSw, deep percolation appears to be greatest beneath active channels of major drainages, diminishing toward the margins and hillslopes bordering these channels. Numerical simulations indicate that this downward percolation is accompanied by lateral spreading as the percolation front moves downward through the PTn and across the contact between the PTn and underlying TSw. Temperature data from a well-documented site in Pagany Wash indicate the presence of a significant heat-flow deficit between the PTn and underlying TSw that most likely is due to nonconductive heat-flow processes with substantial capacity to extract heat. Percolation fluxes on the order of 10 to 20 millimeters per year beneath the Pagany Wash channel and on the order of 5 millimeters per year or less beneath the hillslopes bordering this drainage accounted for the apparent heat-flow deficit. Analyses of borehole temperature gradients in Drill Hole Wash indicate similar percolation fluxes and flux distributions within that drainage. An analysis of residence times estimated from uncorrected carbon-14 activities of perched-water samples and estimates for the volume of the structurally controlled reservoir, however, showed that the perched-water reservoir intersected by borehole UZ-14 under Drill Hole Wash could be sustained by percolation fluxes through the TSw of as little as 0.001 to 0.29 millimeter per year. The significance and implications of these findings with respect to waste isolation are discussed in the appendix of this report.

Nevada↗
USGS1987

Investigation of techniques to estimate rainfall-loss parameters for Illinois

An attempt was made by the U.S. Geological Survey to develop parameter-estimation techniques for two rainfall-loss computation methods used in the U.S. Army Corps of Engineers ' flood-hydrograph model (HEC-1). Six rainfall-loss parameters were investigated - four for the Exponential Loss-Rate method and two for the Initial and Uniform Loss-Rate method. Multiple-regression analyses using data from 616 storms at 98 gaged basins were used to attempt to develop parameter-estimation techniques for ungaged basins in Illinois. Techniques were evaluated using 102 storms at 36 uncalibrated gage basins. Estimated unit-hydrograph and rainfall-loss parameters were used to compute discharge hydrograph characteristics, which were compared with characteristics of observed discharge hydrographs. Seventy and 50% of the simulations using the Exponential Loss-Rate and the Initial and Uniform Loss-Rate methods, respectively, produced valid hydrographs. Model-sensitivity analyses to one standard error of estimate indicate that the storm-dependent rainfall-loss parameters are most significant in reproducing the sum of incremental flows and peak discharge. Time of concentrations and storage coefficient are significant in reproducing time to peak discharge and peak discharge, respectively. The small percentage of variation explained by the estimation techniques and the evaluation results using 102 storms indicates that a large degree of uncertainty exists in the computed hydrographs. (USGS)

Water-Resources Investigations Report↗
USGS1987

Surface-geophysical investigations in Melton Valley, Oak Ridge Reservation, Tennessee

Surface geophysical methods were found to be valuable for refining knowledge of the geohydrology of Melton Valley, an area used for burial of low-level radioactive waste at the Oak Ridge Reservation in Tennessee. The valley is characterized by locally complex geologic structures in lithologies of interbedded shale and limestone. Radionuclides have been transported away from the burial areas by groundwater along paths that are, in part, controlled by geologic structures and rock type. Direct current resistivity soundings were used to determine the depth to bedrock and to aid in the delineation of subsurface stratigraphy. Depth to bedrock, as indicated by an increase in resistivity in the interpreted geoelectric layering, was compared to auger-hole data at five sites, where bedrock depths ranged from 1 to 14 ft and were within 3 ft at four sites. The subsurface contact between shale and limestone was indicated by an increase in model calculated resistivity from < 100 to > 150 ohm-meters at four different sites. Terrain conductivity profiles were used to aid in mapping surficial geologic contacts between shale and limestone units. Terrain conductivity for shale at 33-ft coil separation was generally greater than 15 millimhos/m and ranged from about 10 to 40 millimhos/m. Conductivity for limestone was generally < 15 millimhos/m and ranged from 5 to 25 millimhos/m. Azimuthal conductivity surveys indicated that conductivity was generally greatest when the transmitter and receiver coils were oriented parallel to strike. This anisotropy in terrain conductivity shows the need to keep the coil orientation consistent throughout the length of a profile. (Author 's abstract)

Tennessee↗
USGS1998

Detailed study of selenium and selected constituents in water, bottom sediment, soil, and biota associated with irrigation drainage in the San Juan River area, New Mexico, 1991-95

In response to increasing concern about the quality of irrigation drainage and its potential effects on fish, wildlife, and human health, the U.S. Department of the Interior began the National Irrigation Water Quality Program (NIWQP) to investigate these concerns at irrigation projects sponsored by the Department. The San Juan River area in northwestern New Mexico was one of the areas designated for study. Study teams composed of scientists from the U.S. Geological Survey, the U.S. Fish and Wildlife Service, the Bureau of Reclamation, and the Bureau of Indian Affairs collected water, bottom-sediment, soil, and biological samples at 61 sites in the San Juan River area during 1993-94. Supplemental data collection conducted during 1991-95 by the Bureau of Indian Affairs and its contractor extended the time period and sampling sites available for analysis. Analytical chemistry performed on samples indicated that most potentially toxic elements other than selenium generally were not high enough to be of concern to fish, wildlife, and human health. Element concentrations in some water, bottom-sediment, soil, and biological samples exceeded applicable standards and criteria suggested by researchers in current literature. Selenium concentrations in water samples from 28 sites in the study area exceeded the 2-microgramper-liter (lg/L) wildlife-habitat standard. Vanadium concentrations in water exceeded the 100-Kg/L standard for livestock-drinking water at one site. In biota, selenium and aluminum concentrations regularly equaled or exceeded avian dietary threshold concentrations. In bottom sediment and soil, element concentrations above the upper limit of the baseline range for western soils were: selenium, 24 exceedances; lead, 2 exceedances; molybdenum, 2 exceedances;strontium, 4 exceedances; and zinc, 4 exceedances. Concentrations of total selenium in bottom-sediment and soil samples were significantly greater for Cretaceous than for non-Cretaceous soil types in the study area and were generally similar for habitats within and outside irrigation-affected areas. Mean and median total-selenium concentrations in samples from areas with Cretaceous soil types were 4.6 and 2.2 micrograms per gram (ps/g), respectively. Mean and median total-selenium concentrations in samples from areas with non-Cretaceous soil types were 0.6 and 0.15 pg/g, respectively. Samples from the study area had low concentrations of organic constituents. Organochlorine pesticides and polychlorinated biphenyls were detected in a few biological samples at low concentrations. Polycyclic aromatic hydrocarbon (PAH) compounds were not detected in whole-water samples collected using conventional water-sampling techniques. In tests involving the use of semipermeable-membrane devices to supplement conventional water assays for PAH's, low concentrations of PAH's were found at several locations in the Hammond Irrigation Supply Canal, but were not detected in the Hammond ponds at the downstream reach of the Hammond irrigation service area. PAH compounds do not appear to reach the San Juan River through the Hammond Canal. Data indicate that water samples from irrigation-drainage-affected habitats had increased mean selenium concentrations compared with samples from irrigation-delivery habitat. The mean selenium concentration in water was greatest at seeps and tributaries draining irrigated land (17 μg/L); less in irrigation drains and in ponds on irrigated land (61.tg/L); and least in backwater, the San Juan River, and irrigation-supply water (0.5 - 0.6 μg/L). Statistical tests imply that irrigation significantly increases selenium concentrations in water samples when a Department of the Interior irrigation project is developed on selenium-rich sediments. Water samples from sites with Cretaceous soils had significantly greater selenium concentrations than water samples from sites with non-Cretaceous soils. Water samples from Department of the Interior project irrigation-drainage sites developed on Cretaceous soils contained a mean selenium concentration about 10 times greater than those in samples from Department of the Interior project sites developed on non-Cretaceous soils. Selenium was much less concentrated in water than in bottom sediment, soil, or biota in the study area. The range in concentrations of dissolved selenium in water was less than 1 ptg/L to 37 1.1g/L (less than 1 to 37 parts per billion). The range in concentrations of total selenium in bottom sediment and soil was less than 0.1 to 23lig/g (less than 100 to 23,000 parts per billion). The range in concentration of selenium in biota was less than 0.1 to 24.0 fig/g (less than 100 to 24,000 parts per billion). Data indicated that bioaccumulation and leaching from soil were the important processes at the study area that lead to elevated levels of selenium. Other processes examined included: (1) evapoconcentration of selenium; (2) atmospheric deposition of aerosols containing selenium; and (3) contamination of surface water by point-source or non-point-source discharges. Selenium concentrations in biological samples were evaluated by a number of variables including: (1) media sampled (emergent and submergent plants, nektonic and benthic invertebrates, omnivore/herbivore and carnivore fish, and terrestrial and aquatic amphibians); (2) habitat (San Juan River main-stem reaches, backwaters, tributary reaches, irrigation delivery or drainage canals, and ponds); (3) irrigation project area and reference sites; and (4) soil type (non-Cretaceous or Cretaceous soils). Graphical techniques and nonparametric statistical tests were applied to determine the influence of selected physiographic variables on selenium concentrations in biological samples collected in the San Juan River area. Species of sucker and of smaller fish contained significantly higher selenium concentrations in the upstream portion of the river where a productive community of plants and animals is found that is associated with warming, nutrient-rich waters discharged from an upstream reservoir. Selenium concentrations in algae, odonates, and mosquitofish collected from both irrigation-drain and pond habitats underlain by Cretaceous soils were significantly greater than in those collected from similar habitats underlain by non-Cretaceous soils. Investigators conclude that the major factor affecting the variability of selenium accumulation in biota at aquatic habitats was the presence of underlying Cretaceous soils. Median selenium concentrations were less than 2 lAg/g for plant samples, less than 7 μg/g for invertebrate samples, and less than 6 lAg/g for whole-fish samples collected from aquatic habitats underlain by non-Cretaceous soils. Similar samples collected from aquatic habitats underlain by Cretaceous soils contained median selenium concentrations two to five times greater. Leaching of selenium from Cretaceous soils in the San Juan River area increases the accumulation of selenium concentrations in the biota and thereby increases the exposure and potential health risks associated with selenium to migratory birds, fish, and other wildlife that use these aquatic habitats extensively. Aquatic habitats presenting the greatest average exposure to excess selenium concentrations in the diets of resident wildlife are from consumption of plants, invertebrates, and fish at irrigation-drain habitats underlain by Cretaceous soils. Of the irrigation projects evaluated in the San Juan River area, the highest median selenium concentrations in algae, cattail leaves, odonate nymphs, mosquitofish, and leopard frog samples from the study area were collected from the east hogback irrigation drain.

New Mexico↗
USGS1996

Use of geophysical logs to estimate the quality of ground water and the permeability of aquifers

The relation of formation factor to resistivity of formation water and intergranular permeability has often been investigated, and the general consensus is that this relation is closest when established in a clean-sand aquifer in which water quality does not vary substantially. When these restrictions are applied, the following standard equation is a useful tool in estimating the resistance of the formation water: F = Ro/Rw, where F is the formation factor, which is a function of the effective porosity; Ro is the resistivity of a formation that is 100 percent saturated with interstitial water; and Rw is the resistivity of the water in the saturated zone. However, arenaceous aquifers can have electrical resistivities that are not directly related to resistivity of water or porosity. Surface conductivity and ion exchange are significant factors when the sediments are clay bearing. The solid constituents are a major component of the parameters needed to solve the equation for formation-water resistivity and estimates of aquifer permeability. A correction process needs to be applied to adjust the variables, Ro and F, to the equivalent of clean sand. This report presents an empirical method of using the neutron log and the electrical-resistivity values from long- and short-normal resistivity logs to correct for fine-grained material and the subsequent effects of low impedance to electrical flow that are not related to the resistance of formation water.

Water-Resources Investigations Report↗
USGS2007

Regional impact of water resource investments in an developing area

Regional development and industrialization patterns are investigated and related via regression analysis to water resource investments for the island of Puerto Rico. Although results of this study indicate such investments have little immediate or short‐term impact, significant relationships and variations in regional responses appear over longer time periods. This is shown by applying a variation of Zellner's method of performing seemingly unrelated regressions jointly. By this method, subsets of parameter coefficients of specific economic variables were restricted across regional equations while unrestricted coefficients were interpreted as explaining systematic regional variations in response to public investment. Regional differences, obtained by using this method, are frequently neglected when simply examining the overall development process. Among the more interesting results in terms of policy implications is the apparent significant relationship, over the period considered, between changes in the distribution of income and the pattern of water resource development.

Journal of the American Water Resources Associatio↗
USGS1977

Magmatic behavior of Cu, S, Cl, F, and H 2 O in igneous rocks associated with the Ray porphyry copper deposit, Arizona

Porphyry copper deposits are the subject of a large volume of literature indicating that controversy still reigns as to which model or combination of models explains their origin, and yet, over 70 years ago we reached agreement that the well-documented space-time relationship between the deposits and calc-alkaline plutons indicates a genetic tie between them. This genetic tie is generally assumed to indicate a causitive role for an exposed or nearby hidden pluton. There are many variants, but the two end-member models that incorporate this causitive assumption are the meteoric water model and the orthomagmatic model. It is my opinion that the controversy originates from use of indirect data and variant models to explain new observational data and experimental studies that threaten the survival of the basic end-member models. One of many examples of this is the end-stage magmatic evolution of chlorine-rich water required of the orthomagmatic model. This evolution is required because the low copper content of calc-alkaline plutons demands a large source magma, that, because it generally is not visible, has to be buried. Additionally, much of the ore minerals in porphyry deposits is along fractures. Both conditions require transportation of the ore components from the magma, and to transport enough ore components, given the limited amount of water soluble in a melt and the low solubility of base-metal sulfides in water without benefit of chloride complexing, we required of the original Lindgren magmatic model that the source pluton produced chloride-rich water. However, we did not investigate the rocks associated with deposits to substantiate the hypothesis. We went to the laboratory and found that sufficient water and chlorine could be dissolved in silicate melt in a gold capsule in a high-pressure high-temperature bomb to allow postulation of sufficient water and chlorine in the stocks associated with porphyry deposits; in other words, we invested in indirect rather than direct studies.

Arizona↗
USGS1986

Investigation of the need for discharge adjustments for unsteady flow at selected gaging stations on streams in Tennessee

Measured discharges made during rising or falling stages generally require adjustments to refine constant-stage rating curves (stage-discharge relations) for gaged sites. Measurements at 42 gaging stations on Tennessee streams were selected for adjustment. Two methods, generally accepted by the U.S. Geological Survey, were tested: (1) the slope method adjusts the discharge for changing slope during the measurement, and (2) the storage method adjusts for change in channel storage. Both methods are related to the rate of change in stage. The initial results of the storage method of adjustments were unsatisfactory because of uncertainty in determining channel storage at each site, and a specific trend in the results could not be defined. Consequently, the storage method of adjustment was deleted from successive analyses. Maximum adjustments in measured discharge using the slope method were less than 5 percent at 28 of the 42 stations and less than 10 percent at 39 of the 42 stations used in the analyses. The adjustments were small because most of the measurements were made during nearly stable stage. Adjustments of measurements made during stage changes of several feet per hour could be considerably larger than 10 percent. Stage records at 10 stations showed that maximum change in stage during rises were considerably higher than the change in stage observed during the measurements. Large adjustments are usually required for a short period of time on the rising side of a hydrograph and smaller adjustments are required for a longer period of time on the falling side. Maximum adjustments in discharge using the slope method were less than 5 percent at three of the 10 stations and less than 30 percent at eight of the 10 stations used in the analyses. The mean discharge for the adjusted and unadjusted hydrographs are about the same.

Tennessee↗
USGS1987

Geohydrologic framework of the coastal plain aquifers of South Carolina

The U.S. Geological Survey is conducting a series of investigations of aquifers throughout the United States as a part of the RASA (Regional Aquifer System Analysis) program. These investigations provide a comprehensive regional understanding of groundwater resources throughout the Nation. The Coastal Plain aquifers in South Carolina are being studied as a part of this program. An important part of a description of the groundwater resources is the development of a geohydrologic framework. Such a framework delineates the aquifers through which groundwater flows and the confining units which retard the flow of groundwater between aquifers. The Coastal Plain of South Carolina is underlain by a wedge of sediments that thickens from its inner margin, the Fall Line, to the coast and consists of sand, silt, clay, and limestone of Late Cretaceous to Holocene age. These sediments are underlain by pre-Cretaceous rocks consisting of consolidated sedimentary rocks of Triassic age and a complex of metamorphic and igneous rocks similar to those found near the surface in the Piedmont province of the State. The geohydrologic framework that divides the sediments of the South Carolina Coastal Plain into the Coastal Plain aquifer system is delineated by eleven geohydrologic sections and four maps showing the configuration of the top or base of individual aquifers. Although flow within the Coastal Plain aquifer system is three dimensional, simplifying the system by dividing it into a framework of discrete hydrologic units can aid significantly in understanding the hydrology of the system. This framework is the basis for the aquifers used in potentiometric mapping, transmissivity mapping, geochemical analysis, and groundwater flow modeling for the South Carolina RASA program. (Lantz-PTT)

South Carolina↗
USGS2001

Benthic invertebrate communities and their responses to selected environmental factors in the Kanawha River basin, West Virginia, Virginia, and North Carolina

The effects of selected environmental factors on the composition and structure of benthic invertebrate communities in the Kanawha River Basin of West Virginia, Virginia and North Carolina were investigated in 1997 and 1998. Environmental factors investigated include physiography, land-use pattern, streamwater chemistry, streambed- sediment chemistry, and habitat characteristics. Land-use patterns investigated include coal mining, agriculture, and low intensity rural-residential patterns, at four main stem and seven tributary sites throughout the basin. Of the 37 sites sampled, basin size and physiography most strongly affected benthic invertebrate-community structure. Land-use practices also affected invertebrate community structure in these basins. The basins that differed most from the minimally affected reference condition were those basins in which coal mining was the dominant nonforest land use, as determined by comparing invertebrate- community metric values among sites. Basins in which agriculture was important were more similar to the reference condition. The effect of coal mining upon benthic invertebrate communities was further studied at 29 sites and the relations among invertebrate communities and the selected environmental factors of land use, streamwater chemistry, streambed- sediment chemistry, and habitat characteristics analyzed. Division of coal-mining synoptic-survey sites based on invertebrate-community composition resulted in two groups?one with more than an average production of 9,000 tons of coal per square mile per year since 1980, and one with lesser or no recent coal production. The group with significant recent coal production showed higher levels of community impairment than the group with little or no recent coal production. Median particle size of streambed sediment, and specific conductance and sulfate concentration of streamwater were most strongly correlated with effects on invertebrate communities. These characteristics were related to mining intensity, as measured by thousands of tons of coal produced per square mile of drainage area.

North Carolina, Virginia, West Virginia↗
USGS1997

Regional equations for estimation of peak-streamflow frequency for natural basins in Texas

Peak-streamflow frequency estimates are needed for flood-plain management; for objective assessment of flood risk; and for cost-effective design of dams, levees, other flood-control structures, roads, bridges, and culverts. Peak-streamflow frequency represents the peak discharges for recurrence intervals of 2, 5, 10, 25, 50, and 100 years. The U.S. Geological Survey, in cooperation with the Texas Department of Transportation, conducted an investigation to develop regional regression equations for the estimation of peak-streamflow frequency for ungaged sites in natural basins in Texas. Peak-streamflow frequency data from streamflow-gaging stations in natural drainage basins of Texas were used. Peak-streamflow frequency for 559 Texas stations with natural (unregulated and rural or nonurbanized) basins was estimated with annual peak-streamflow data through 1993. The peak-streamflow frequency and drainage-basin characteristics for the Texas stations were used to develop 16 sets of equations to estimate peak-streamflow frequency for ungaged natural stream sites in each of 11 regions in Texas. The relation between peak-streamflow frequency and contributing drainage area for 5 of the 11 regions is curvilinear, requiring that one set of equations be developed for drainage areas less than 32 square miles and another set be developed for drainage areas greater than 32 square miles. These equations, developed through multiple-regression analysis using weighted least squares, are based on the relation between peak-streamflow frequency and basin characteristics for streamflow-gaging stations. The regions represent areas with similar flood characteristics. The use and limitations of the regression equations also are discussed. Additionally, procedures are presented to compute the 50-, 67-, and 90-percent confidence limits for any estimation from the equations. Also, supplemental peak-streamflow frequency and basin characteristics for 105 selected stations bordering Texas are included in the report. This supplemental information will aid in interpretation of flood characteristics for sites near the state borders of Texas.

Texas↗
USGS1986

Effect of bank protection measures, Stehekin River, Chelan County, Washington

An investigation of the lower Stehekin River was conducted to study the effects on flood elevations and velocities from four bank protection and flood prevention measures that are being contemplated as a means of reducing erosional losses of river bank property. These measures are: bank armoring, armored revetment levees, spur dikes, and redevelopment of old cutoff channels. The banks at seven study sites could be armored without adverse effect on the flood velocities and elevations. The largest increases due to armoring--up to 1.6 ft/sec in velocity and 1 ft in elevation--occurred in the vicinity of sites 5, 6, and 7 where the gradient of the river channel is about 50 ft/mi and the velocities are high to begin with (about 6 to 13 ft/sec). The use of a levee in conjunction with armoring on the northeast bank from sites 5 to 7 would increase the velocities as much as 2.8 ft/sec and increase the elevation as much as 1 ft, but it would also provide some flood protection to the east bank, which is frequently inundated. Spur dikes were considered a practical alternative only at site 3, where reduced bank erosion may occur without aggravating flood inundation or erosion elsewhere. The rerouting of flood flow through an old cutoff channel near site 1 increased the velocity by 3.2 ft/sec and the elevation by 1 ft for the 100-year flood; however, it would move floodwater away from residential property where bank erosion is a problem. The few other old channels that shortcut river bends where much erosion occurs are apparently already part of the channel during floods. (Author 's abstract)

Water-Resources Investigations Report↗
USGS1994

Investigation of bridge scour at selected sites on Missouri streams

Scour around bridge piers is a major concern in the design of a new bridge or the evaluation of the structural stability of an existing bridge. An adequate estimation of potential scour at bridge piers is essential to effective design, construction, and maintenance of hydraulic structures. Reasonably accurate estimates of scour depth are needed for safe, cost-effective bridge design. Although many equations have been developed on the basis of laboratory work that can be used to estimate local scour at piers, site-specific data have not previously been collected to verify the accuracy of these equations or applicability to Missouri streams. Scour data were collected during floods at 10 sites on streams in Missouri. The recurrence intervals of the floods ranged from less than 2 to more than 50 years. Local-scour holes near bridge piers ranged from 0.5 to 7.1 feet deep. Seven local-pier-scour equations were evaluated as to their usefulness in estimating the measured scour at the sites studied. Scour depths estimated using the Froehlich equatin without a safety factor had an interquartile range nearest in magnitude to the interquartile range of the measured scour depths. None of the medians of scour depths estimated using the seven equations were statistically equal to the median of the measured scour depths at a 0.05 level of significance. However, the Froehlich equation without a safety factor provided the "best fit" estimates of the equations considered. Contraction scour exceeded local scour by several times in some cases. Total scour of approximately 19 feet, largely becasue of contraction scour, was measured at the Chariton River near Prairie Hill during the flood of July 8, 1993. This large scour was, in part, the result of an accumulation of woody debris de- creasing the bridge-opening area. A bridge on State Highway 32 near Lebanon over North Cobb Creek (drainage area 52.5 square miles) was destroyed during the flood of May 26, 1990. Bridge scour attributable to contraction of the flood flow caused this loss.

Missouri↗
USGS1985

Cost effectiveness of stream-gaging program in Michigan

This report documents the results of a study of the cost effectiveness of the stream-gaging program in Michigan. Data uses and funding sources were identified for the 129 continuous gaging stations being operated in Michigan as of 1984. One gaging station was identified as having insufficient reason to continue its operation. Several stations were identified for reactivation, should funds become available, because of insufficiencies in the data network. Alternative methods of developing streamflow information based on routing and regression analyses were investigated for 10 stations. However, no station records were reproduced with sufficient accuracy to replace conventional gaging practices. A cost-effectiveness analysis of the data-collection procedure for the ice-free season was conducted using a Kalman-filter analysis. To define missing-record characteristics, cross-correlation coefficients and coefficients of variation were computed at stations on the basis of daily mean discharge. Discharge-measurement data were used to describe the gage/discharge rating stability at each station. The results of the cost-effectiveness analysis for a 9-month ice-free season show that the current policy of visiting most stations on a fixed servicing schedule once every 6 weeks results in an average standard error of 12.1 percent for the current $718,100 budget. By adopting a flexible servicing schedule, the average standard error could be reduced to 11.1 percent. Alternatively, the budget could be reduced to $700,200 while maintaining the current level of accuracy. A minimum budget of $680,200 is needed to operate the 129-gaging-station program; a budget less than this would not permit proper service and maintenance of stations. At the minimum budget, the average standard error would be 14.4 percent. A budget of $789,900 (the maximum analyzed) would result in a decrease in the average standard error to 9.07 percent. Owing to continual changes in the composition of the network and the changes in the uncertainties of streamflow accuracy at individual stations, the cost-effectiveness analysis will need to be updated regularly if it is to be used as a management tool. Cost of these updates need to be considered in decisions concerning the feasibility of flexible servicing schedules.

Michigan↗
USGS1998

Lithology and fracture characterization from drilling investigations in the Mirror Lake area, Grafton County, New Hampshire

The lithology and fracture network of the bedrock aquifer in the Mirror Lake area were characterized from hydrogeologic data collected from 1979-95 in Grafton County, N.H. The collection of these data is an integral part of an ongoing multidisciplinary study by the U.S. Geological Survey to characterize groundwater flow and solute transport in fractured rock. The data provide a physical framework and enable the characterization of the fractures and the rock types in the bedrock aquifer in the Mirror Lake study area. In addition, these data provide a detailed description of the subsurface intersected by boreholes that can be used to compare the results of other borehole testing. The Mirror Lake area is characterized by steep bedrock uplands that are mostly covered by colluvium, discontinuous stratified-drift deposits, and glacial till that varies locally in thickness from less than 10 meters to as much as 50 meters. The land-surface altitude ranges from 180 meters near the Pemigewasset River to 720 meters on the mountain top on the northwestern side of the study area. The bedrock in the area is predominantly sillimanite-grade pelitic schists that have been complexly folded and intruded by granitoids, pegmatites, and diabase dikes. The bedrock has been fractured in response to local and tectonic stress. The resulting interconnected network of fractures forms the bedrock aquifer. This report describes the lithologic units in the study area and provides a characterization of the lithology and fractures found in 40 boreholes, which range in depth from 60 to 305 meters, that were drilled for this study. Drilling logs and color video surveys were used to locate and characterize the fractures and rock types in the subsurface. Solid bedrock core was obtained from three of the boreholes. Petrographic thin-section, x-ray diffraction and scanning electron microscope with energy dispersive x-ray fluorescence spectrometry analyses were done on selected samples from boreholes and outcrops. Observations recorded at the time of drilling, descriptions of rock samples collected from the boreholes, interpretation of rock type and fractures based on boreholeimaging surveys, descriptions of rock core and petrographic analyses of selected rock samples are in tables and figures. Analysis of the data provided information on the distribution of fractures and lithology in the boreholes at Mirror Lake. The relative abundances of the rock types were computed for three groups of boreholes, including (1) the Forest Service Experimental (FSE) well field, (2) the Camp Osceola (CO) well field, and (3) the index boreholes, which are 15 boreholes distributed areally throughout the study area including the deepest borehole from each of the two well fields. The index boreholes are separated by hundreds of meters and are typically 100 meters deep. The FSE well field includes 13 boreholes that are separated by 10 to 40 meters. These 13 boreholes are approximately 100 meters deep, except for one borehole that is 230 meters deep. The rocks penetrated by the FSE wells are predominantly igneous. Approximately 70 percent of the rocks encountered in the boreholes in the FSE well field were granite, pegmatite, and aplite. The CO well field includes 9 boreholes that range from 60-70 meters deep and one borehole that is 175 meters deep. The rocks encountered in these boreholes were predominantly metamorphic. The distribution of rock types in the CO well field is similar to the distribution of rocks in highway roadcuts, that are approximately 90 to 150 meters east of the well field. Seventy percent of the roadcut exposures are schist. Collectively, in the 15 index boreholes, the metamorphic and igneous rocks are equally distributed. Analysis of the rock types in these boreholes indicates that the rock types tend to "change" every 5 to 9 meters. Although the metamorphic and igneous rocks each comprise approximately 50 percent of the rock types observed in the 15 index boreholes, 73 percent of the fractures were in the igneous rocks. This indicates that the granitoids tend to be more fractured than the metamorphic rocks. Pegmatite, diabase, quartzite, and gneissic rocks are relatively unfractured. Boreholes completed in bedrock generally have one or two water-bearing zones, which were identified during the drilling process. At the completion of drilling a borehole, the driller estimated the yield of the borehole with an air-lift test. Yields estimated by drillers ranged from less than 3 to 378 liters per minute. These yields are typical of the yields measured for domestic wells in Grafton County. Water levels measured in the open boreholes after the boreholes recovered from the hydraulic stresses of drilling were usually in the steel casing and were within 10 meters of the land surface. Water levels in eight of the boreholes were above the top of casing or above land surface.

New Hampshire↗
USGS2002

Results of Hydraulic Tests in Miocene Tuffaceous Rocks at the C-Hole Complex, 1995 to 1997, Yucca Mountain, Nye County, Nevada

Four hydraulic tests were conducted by the U.S. Geological Survey at the C-hole complex at Yucca Mountain, Nevada, between May 1995 and November 1997. These tests were conducted as part of ongoing investigations to determine the hydrologic and geologic suitability of Yucca Mountain as a potential site for permanent underground storage of high-level nuclear waste. The C-hole complex consists of three 900-meter-deep boreholes that are 30.4 to 76.6 meters apart. The C-holes are completed in fractured, variably welded tuffaceous rocks of Miocene age. Six hydrogeologic intervals occur within the saturated zone in these boreholes - the Calico Hills, Prow Pass, Upper Bullfrog, Lower Bullfrog, Upper Tram, and Lower Tram intervals. The Lower Bullfrog and Upper Tram intervals contributed about 90 percent of the flow during hydraulic tests. The four hydraulic tests conducted from 1995 to 1997 lasted 4 to 553 days. Discharge from the pumping well, UE-25 c #3, ranged from 8.49 to 22.5 liters per second in different tests. Two to seven observation wells, 30 to 3,526 meters from the pumping well, were used in different tests. Observation wells included UE-25 c #1, UE-25 c #2, UE-25 ONC-1, USW H-4, UE-25 WT #14, and UE-25 WT #3 in the tuffaceous rocks and UE-25 p #1 in Paleozoic carbonate rocks. In all hydraulic tests, drawdown in the pumping well was rapid and large (2.9-11 meters). Attributable mostly to frictional head loss and borehole-skin effects, this drawdown could not be used to analyze hydraulic properties. Drawdown and recovery in intervals of UE-25 c #1 and UE-25 c #2 and in other observation wells typically was less than 51 centimeters. These data were analyzed. Hydrogeologic intervals in the C-holes have layered heterogeneity related to faults and fracture zones. Transmissivity, hydraulic conductivity, and storativity generally increase downhole. Transmissivity ranges from 4 to 1,600 meters squared per day; hydraulic conductivity ranges from 0.1 to 50 meters per day; and storativity ranges from 0.00002 to 0.002. Transmissivity in the Miocene tuffaceous rocks decreases from 2,600 to 700 meters squared per day northwesterly across the 21-square-kilometer area affected by hydraulic tests at the C-hole complex. The average transmissivity of the tuffaceous rocks in this area, as determined from plots of drawdown in most or all observation wells as functions of time or distance from the pumping well, is 2,100 to 2,600 meters squared per day. Average storativity determined from these plot ranges is 0.0005 to 0.002. Hydraulic conductivity ranges from less than 2 to more than 10 meters per day; it is largest where prominent northerly trending faults are closely spaced or intersected by northwesterly trending faults. During hydraulic tests, the Miocene tuffaceous rocks functioned as a single aquifer. Drawdown occurred in all monitored intervals of the C-holes and other observation wells, regardless of the hydrogeologic interval being pumped. This hydraulic connection across geologic and lithostratigraphic contacts is believed to result from interconnected faults, fractures, and intervals with large matrix permeability. Samples of UE-25 c #3 water, analyzed from 1995 to 1997, seem to indicate that changes in the quality of the water pumped from that well are probably due solely to lateral variations in water quality within the tuffaceous rocks.

Water-Resources Investigations Report↗
USGS1999

Depth-Duration Frequency of Precipitation for Oklahoma

A regional frequency analysis was conducted to estimate the depth-duration frequency of precipitation for 12 durations in Oklahoma (15, 30, and 60 minutes; 1, 2, 3, 6, 12, and 24 hours; and 1, 3, and 7 days). Seven selected frequencies, expressed as recurrence intervals, were investigated (2, 5, 10, 25, 50, 100, and 500 years). L-moment statistics were used to summarize depth-duration data and to determine the appropriate statistical distributions. Three different rain-gage networks provided the data (15minute, 1-hour, and 1-day). The 60-minute, and 1-hour; and the 24-hour, and 1-day durations were analyzed separately. Data were used from rain-gage stations with at least 10-years of record and within Oklahoma or about 50 kilometers into bordering states. Precipitation annual maxima (depths) were determined from the data for 110 15-minute, 141 hourly, and 413 daily stations. The L-moment statistics for depths for all durations were calculated for each station using unbiased L-mo-ment estimators for the mean, L-scale, L-coefficient of variation, L-skew, and L-kur-tosis. The relation between L-skew and L-kurtosis (L-moment ratio diagram) and goodness-of-fit measures were used to select the frequency distributions. The three-parameter generalized logistic distribution was selected to model the frequencies of 15-, 30-, and 60-minute annual maxima; and the three-parameter generalized extreme-value distribution was selected to model the frequencies of 1-hour to 7-day annual maxima. The mean for each station and duration was corrected for the bias associated with fixed interval recording of precipitation amounts. The L-scale and spatially averaged L-skew statistics were used to compute the location, scale, and shape parameters of the selected distribution for each station and duration. The three parameters were used to calculate the depth-duration-frequency relations for each station. The precipitation depths for selected frequencies were contoured from weighted depth surfaces to produce maps from which the precipitation depth-duration-frequency curve for selected storm durations can be determined for any site in Oklahoma.

Water-Resources Investigations Report↗