Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Topographic Map”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60Linked to original sources
USGS2016

Continental Shelf Morphology and Stratigraphy Offshore San Onofre, CA: The Interplay Between Rates of Eustatic Change and Sediment Supply

New high-resolution CHIRP seismic data acquired offshore San Onofre, southern California reveal that shelf sediment distribution and thickness are primarily controlled by eustatic sea level rise and sediment supply. Throughout the majority of the study region, a prominent abrasion platform and associated shoreline cutoff are observed in the subsurface from ~ 72 to 53 m below present sea level. These erosional features appear to have formed between Melt Water Pulse 1A and Melt Water Pulse 1B, when the rate of sea-level rise was lower. There are three distinct sedimentary units mapped above a regional angular unconformity interpreted to be the Holocene transgressive surface in the seismic data. Unit I, the deepest unit, is interpreted as a lag deposit that infills a topographic low associated with an abrasion platform. Unit I thins seaward by downlap and pinches out landward against the shoreline cutoff. Unit II is a mid-shelf lag deposit formed from shallower eroded material and thins seaward by downlap and landward by onlap. The youngest, Unit III, is interpreted to represent modern sediment deposition. Faults in the study area do not appear to offset the transgressive surface. The Newport Inglewood/Rose Canyon fault system is active in other regions to the south (e.g., La Jolla) where it offsets the transgressive surface and creates seafloor relief. Several shoals observed along the transgressive surface could record minor deformation due to fault activity in the study area. Nevertheless, our preferred interpretation is that the shoals are regions more resistant to erosion during marine transgression. The Cristianitos fault zone also causes a shoaling of the transgressive surface. This may be from resistant antecedent topography due to an early phase of compression on the fault. The Cristianitos fault zone was previously defined as a down-to-the-north normal fault, but the folding and faulting architecture imaged in the CHIRP data are more consistent with a strike-slip fault with a down-to-the-northwest dip-slip component. A third area of shoaling is observed off of San Mateo and San Onofre creeks. This shoaling has a constructional component and could be a relict delta or beach structure. (C) 2015 Elsevier B.V. All rights reserved.

California↗
USGS2018

Coastal National Elevation Database

The Coastal National Elevation Database (CoNED) Applications Project develops enhanced topographic (land elevation) and bathymetric (water depth) datasets that serve as valuable resources for coastal hazards research (Danielson and others, 2016; Thatcher and others, 2016). These datasets are used widely for mapping inundation zones from riverine flood events, hurricanes, and sea-level rise and for other Earth science applications, such as sediment transport, erosion, and storm impact models. CoNED is a U.S. Geological Survey (USGS) Coastal-Marine Hazards and Resources Program (formerly Coastal and Marine Geology Program) activity centered at the USGS Earth Resources Observation and Science Center and distributed at other USGS Science Centers. As part of the vision for a 3D Nation, the CoNED Project is working collaboratively with the USGS National Geospatial Program, the National Oceanic and Atmospheric Administration, and the U.S. Army Corps of Engineers through the Interagency Working Group on Ocean and Coastal Mapping to build integrated elevation models in the coastal zone by assimilating the land surface topography with littoral zone and continental shelf bathymetry. Several nongovernmental organizations and Federal agencies, including the Department of the Interior Pacific Islands Climate Adaptation Science Center, the National Park Service, the Nature Conservancy, the Louisiana Coastal Protection and Restoration Authority, and numerous academic institutions, partner to make CoNED a success.

Fact Sheet↗
USGS2013

Generalized surficial geologic map of the Fort Irwin Area, San Bernardino County, California

The geology and landscape of the Fort Irwin area, typical of many parts of the Mojave Desert, consist of rugged mountains separated by broad alluviated valleys that form the main coarse-resolution features of the geologic map. Crystalline and sedimentary rocks, Mesozoic and older in age, form most of the mountains with lesser accumulations of Miocene sedimentary and volcanic rocks. In detail, the area exhibits a fairly complex distribution of surficial deposits resulting from diverse rock sources and geomorphology that has been driven by topographic changes caused by recent and active faulting. Depositional environments span those typical of the Mojave Desert: alluvial fans on broad piedmonts, major intermittent streams along valley floors, eolian sand dunes and sheets, and playas in closed valleys that lack through-going washes. Erosional environments include rocky mountains, smooth gently sloping pediments, and badlands in readily eroded sediment. All parts of the landscape, from regional distribution of mountains, valleys, and faults to details of degree of soil development in surface materials, are portrayed by the surficial geologic map. Many of these attributes govern infiltration and recharge, and the surface distribution of permeable rock units such as Miocene sedimentary and volcanic rocks provides a basis for evaluating potential groundwater storage. Quaternary faults are widespread in the Fort Irwin area and include sinistral, east-striking faults that characterize the central swath of the area and the contrasting dextral, northwest-striking faults that border the east and west margins. Bedrock distribution and thickness of valley-fill deposits are controlled by modern and past faulting, and faults on the map help to identify targets for groundwater exploration.

California↗
USGS2021

Delineating the Pierre Shale from geophysical surveys within and near Ellsworth Air Force Base, South Dakota, 2019

The U.S. Geological Survey, in cooperation with the U.S. Air Force Civil Engineering Center, investigated the use of surface geophysical methods to delineate the top of the Cretaceous Pierre Shale along survey transects in selected areas within and near Ellsworth Air Force Base, South Dakota. Two complementary geophysical methods—electrical resistivity and passive seismic—were used along 26 co-located transect surveys within and near Ellsworth Air Force Base for a total of 12.7 line-kilometers. Electrical resistivity results were analyzed using EarthImager2D electrical resistivity tomography processing and inversion software. Two-dimensional earth models showing the electrical properties of the subsurface were evaluated by directly comparing the high and low subsurface resistivity values to a surficial geologic map and nearby wells with driller logs. Passive seismic data were analyzed using the horizontal-to-vertical spectral ratio method to determine the depth to the Pierre Shale at each survey point. The electrical resistivity and passive seismic results were compared to driller logs from nearby wells to delineate the top of the Pierre Shale. The depth to the Pierre Shale along the transects ranged from about 2.4 to 20.3 meters, and mean and median depths were about 9.2 and 9.0 meters, respectively. The elevation of the Pierre Shale and thickness of unconsolidated deposits generally increased with land-surface elevation from south to north; however, some transects displayed topographically high and low areas that sometimes did not correlate with land-surface topography and may affect local groundwater flow.

South Dakota↗
USGS1983

Airborne biogeophysical mapping of hidden mineral deposits

Airborne survey techniques have been developed to detect and map forest canopies affected by metal-induced stress. A high spectral resolution airborne spectroradiometer system, used over a known forest-covered copper soil anomaly, has revealed previously unknown spectral changes in the near-infrared chlorophyll absorption spectrum. The metal-induced spectral shifts have subsequently been reproduced in the laboratory at Columbia University. Waveform analysis techniques specifically designed for computer analysis of the high spectral resolution aircraft data filter out the very strong background noise introduced by variations in normal, unstressed vegetation canopy and by topographic effects. The wave-form method proves most effective in extracting the subtle spectral indicators of metal-induced stress. The analytic method is a unique frequency domain technique made possible by the high spectral resolution of the 500-channel spectroradiometer system. The biogeophysical technique is demonstrated by three mapping surveys of Cotter Basin, Montana, and Spirit Lake, Washington. This airborne mapping technique presents new application opportunities in large areas of the world where heavy forest cover has in the past made geologic and geophysical exploration tedious and expensive. The tree cover with widespreading and deeply penetrating root systems is turned to an advantage in the airborne biogeophysical technique by detecting metal-induced changes in the chlorophyll reflectance spectrum.

Montana↗
USGS1991

Regional study of mineral resources in Nevada: Insights from three-dimensional analysis of gravity and magnetic anomalies

A three-dimensional interpretation of the basins of Nevada was developed based on statewide data bases of digital-gravity, magnetic, geologic, well, and topographic information. An iterative technique was applied to isostatic residual gravity anomalies in Nevada in order to define the location and shape of pre-Tertiary basement and to produce a gravity map that reflects variations of density within the pre-Tertiary basement. The dominant feature of the basement gravity of Nevada is an enormous area of low gravity that spans the entire state between latitudes 37°N and 40.5°N. This regional low strongly correlates with the distribution of middle and late Tertiary volcanic rocks and may reflect silicic intrusions within the mid-crust and upper crust that are the counterparts of volcanic rocks at the surface. Although 80% of Nevada is covered by Cenozoic deposits, these deposits are thicker than 1 km over only about 20% of the state. The remaining 60% of Nevada may have pre-Tertiary basement rocks within reach of current mineral-exploration techniques. Aeromagnetic profiles from the National Uranium Resource Evaluation (NURE) were analyzed in order to produce a map showing the location of shallow magnetic sources in Nevada. This analysis shows that 46% of the state has magnetic sources, generally Mesozoic and Cenozoic igneous rocks, within 1 km of the surface. A linear magnetic anomaly in north-central Nevada has been interpreted by others as a rift zone active during middle Miocene time. The rift also is evident in NURE magnetic profiles, but our interpretation suggests that the magnetic expression of the rift continues south-southeast with similar strike to at least 38°N and perhaps to the amagmatic zone (lat. 37°N). The survival since the middle Miocene of this narrow crustal feature, essentially linear over a distance of 500 km, is difficult to interpret in light of later Basin and Range deformation. Our analysis of gravity anomalies shows that many deep Cenozoic basins are located near the rift, yet only two basins cut across it, and at least five others change strike near the rift, as if to avoid it. The rift may have remained linear because it is associated with crustal structures that acted to resist subsequent deformation.

Nevada↗
USGS2017

Hydrologic Derivatives for Modeling and Analysis—A new global high-resolution database

The U.S. Geological Survey has developed a new global high-resolution hydrologic derivative database. Loosely modeled on the HYDRO1k database, this new database, entitled Hydrologic Derivatives for Modeling and Analysis, provides comprehensive and consistent global coverage of topographically derived raster layers (digital elevation model data, flow direction, flow accumulation, slope, and compound topographic index) and vector layers (streams and catchment boundaries). The coverage of the data is global, and the underlying digital elevation model is a hybrid of three datasets: HydroSHEDS (Hydrological data and maps based on SHuttle Elevation Derivatives at multiple Scales), GMTED2010 (Global Multi-resolution Terrain Elevation Data 2010), and the SRTM (Shuttle Radar Topography Mission). For most of the globe south of 60°N., the raster resolution of the data is 3 arc-seconds, corresponding to the resolution of the SRTM. For the areas north of 60°N., the resolution is 7.5 arc-seconds (the highest resolution of the GMTED2010 dataset) except for Greenland, where the resolution is 30 arc-seconds. The streams and catchments are attributed with Pfafstetter codes, based on a hierarchical numbering system, that carry important topological information. This database is appropriate for use in continental-scale modeling efforts. The work described in this report was conducted by the U.S. Geological Survey in cooperation with the National Aeronautics and Space Administration Goddard Space Flight Center.

Data Series↗
USGS2001

Potentiometric surface of the upper Patapsco aquifer in southern Maryland, September 1999

This report presents a map showing the potentiometric surface of the Upper Patapsco aquifer in the Patapsco Formation of Cretaceous age in Southern Maryland during September 1999. The map is based on water-level measurements in 49 wells. The potentiometric surface was 119 feet above sea level near the northern boundary and outcrop area of the aquifer in a topographically high area of Anne Arundel County, and 55 feet above sea level in a similar setting in Prince Georges County. From these high areas, the potentiometric surface declined to the southeast toward large well fields in the Annapolis area, and from all directions toward a cone of depression southwest of Waldorf. Ground-water levels declined to 20 feet below sea level in the Annapolis area, and 131 feet below sea level southwest of Waldorf.

Open-File Report↗
USGS2001

Changes in riparian vegetation in the Southwestern United States: Historical Changes along the Mojave River, California

This report presents a map showing the potentiometric surface of the Upper Patapsco aquifer in the Patapsco Formation of Cretaceous age in Southern Maryland during September 1999. The map is based on water-level measurements in 49 wells. The potentiometric surface was 119 feet above sea level near the northern boundary and outcrop area of the aquifer in a topographically high area of Anne Arundel County, and 55 feet above sea level in a similar setting in Prince Georges County. From these high areas, the potentiometric surface declined to the southeast toward large well fields in the Annapolis area, and from all directions toward a cone of depression southwest of Waldorf. Ground-water levels declined to 20 feet below sea level in the Annapolis area, and 131 feet below sea level southwest of Waldorf.

Open-File Report↗
USGS2006

Potentiometric Surface of the Upper Floridan Aquifer in the St. Johns River Water Management District and Vicinity, Florida, May 2005

INTRODUCTION This map depicts the potentiometric surface of the upper Floridan aquifer in the St. Johns River Water Management District and vicinity for May 2005. Potentiometric contours are based on water level measurements collected at 598 wens during the period May 5 - 31, near the end of the dry season. Some contours are inferred from previous potentiometric-surface maps with larger well networks. The potentiometric surface of the carbonate upper Floridan aquifer responds mainly to rainfall, and more locally, to ground water withdrawals. Potentiometric-surface highs generally correspond to topographic highs where the aquifer is recharged. Springs and areas of diffuse upward leakage naturally discharge water from the aquifer and are most prevalent along the St. Johns River. Areas of discharge are reflected by depressions in the potentiometric surface. Ground water withdrawals locally have lowered the potentiometric surface. Ground water in the upper Floridan aquifer generally flows from potentiometric highs to potentiometric lows in a direction perpendicular to the contours.

Open-File Report↗
USGS1909

Geology and water resources of the northern portion of the Black Hills and adjoining regions in South Dakota and Wyoming

This paper, which supplements the report on the geology and water resources of the southern half of the Black Hills, published in 1901, is the result of studies made at intervals during the years 1899 to 1907. It relates to an area of about 7,500 square miles, situated about half in South Dakota and half in the northeast corner of Wyoming (Pl. II), and covering the northern half of the Black Hills uplift and a wide area of adjacent plains. The report describes the geology of the sedimentary rocks - their stratigraphy, structure, and history - and discusses their mineral resources, including underground water, coal, gypsum, etc. It also contains information respecting surface waters available for irrigation and stock raising, timber, climate, and the history of the topographic development of the region. The crystalline rocks of the central portion of the Black Hills area and the various igneous rocks of later age are shown on some of the accompanying maps but without differentiation, as the study of their geology was not within the scope of the investigation; neither are their mineral resources considered here, for these are treated in other publications. In the field work I have been assisted mainly by Prof. C. C. O'Harra, of the School of Mines at Rapid, who has mapped the geology of large areas about Aladdin, the Devils Tower, Belle Fourche, and Rapid. Dr. W. S. Tangier Smith has mapped portions of the Bear Lodge and Nigger Hill uplifts, and Mr. C. A. Fisher has assisted in portions of the work. The geology of the region from Sturgis to a point beyond Spearfish Canyon was mapped by Prof. T. A. Jaggar, jr., with the assistance of Mr. J. M. Boutwell, in 1898 and 1899. It is desirable to repeat here the statement made in my previous report that all who study the geology of the Black Hills must feel impressed by the remarkably clear general conceptions of the geologic relations of this region afforded by the survey made by Mr. Henry Newton over a quarter of a century ago. In one short season, with many unfavorable conditions for traveling, he determined most of the broader features and recorded many of the essential details. His posthumous report, edited by Mr. G. K. Gilbert, will always remain a standard work on Black Hills geology. Later studies have added greatly to our knowledge of the details of the stratigraphy and structure, the distribution of the rocks and minerals, and the age of the beds, and have afforded means for a more complete elucidation of the geologic history, especially the physiographic development of the Black Hills region.

South Dakota, Wyoming↗
USGS2012

Geologic map of the Themis Regio quadrangle (V-53), Venus

The Themis Regio quadrangle (V-53), Venus, has been geologically mapped at 1:5,000,000 scale as part of the NASA Planetary Geologic Mapping Program. The quadrangle extends from lat 25° to 50° S. and from long 270° to 300° E. and encompasses the Themis Regio highland, the surrounding plains, and the southernmost extension of Parga Chasmata. Themis Regio is a broad regional topographic high with a diameter of about 2,000 km and a height of about 0.5 km that has been interpreted previously as a hotspot underlain by a mantle plume. The Themis rise is dominated by coronae and lies at the terminus of the Parga Chasmata corona chain. Themis Regio is the only one of the three corona-dominated rises that contains significant extensional deformation. Fractures and grabens are much less common than along the rest of Parga Chasmata and are embayed by corona-related flows in places. Rift and corona formation has overlapped in time at Themis Regio.

Scientific Investigations Map↗
USGS2014

Assessing the importance of terrain parameters on glide avalanche release

Glide snow avalanches are dangerous and difficult to predict. Despite recent research there is still a lack of understanding regarding the controls of glide avalanche release. Glide avalanches often occur in similar terrain or the same locations annually and observations suggest that topography may be critical. Thus, to gain an understanding of the terrain component of these types of avalanches we examined terrain parameters associated with glide avalanche release as well as areas of consistent glide crack formation but no subsequent avalanches. Glide avalanche occurrences visible from the Going-to-the-Sun Road corridor in Glacier National Park, Montana from 2003-2013 were investigated using an avalanche database derived of daily observations each year from April 1 to June 15. This yielded 192 glide avalanches in 53 distinct avalanche paths. Each avalanche occurrence was digitized in a GIS using satellite, oblique, and aerial imagery as reference. Topographical parameters such as area, slope, aspect, elevation and elevation were then derived for the entire dataset utilizing GIS tools and a 10m DEM. Land surface substrate and surface geology were derived from National Park Service Inventory and Monitoring maps and U.S. Geological Survey surface geology maps, respectively. Surface roughness and glide factor were calculated using a four level classification index. . Then, each avalanche occurrence was aggregated to general avalanche release zones and the frequencies were compared. For this study, glide avalanches released in elevations ranging from 1300 to 2700 m with a mean aspect of 98 degrees (east) and a mean slope angle of 38 degrees. The mean profile curvature for all glide avalanches was 0.15 and a plan curvature of -0.01, suggesting a fairly linear surface (i.e. neither convex nor concave). The glide avalanches occurred in mostly bedrock made up of dolomite and limestone slabs and talus deposits with very few occurring in alpine meadows. However, not all glide avalanches failed as cohesive slabs on this bedrock surface. Consequently, surface roughness proved to be a useful descriptive variable to discriminate between slopes that avalanched and those that did not. Annual 'repeat offender' glide avalanche paths were characterized by smooth outcropping rock plates with stratification planes parallel to the slope. Combined with aspect these repeat offenders were also members of the highest glide category. Using this understanding of the role of topographic parameters on glide avalanche activity, a spatial terrain based model was developed to identify other areas with high glide avalanche potential outside of our immediate observation area.

Montana↗
USGS2008

Potentiometric surface of the upper Floridan aquifer in the St. Johns River Water Management District and vicinity, May 2008

This map depicts the potentiometric surface of the Upper Floridan aquifer in the St. Johns River Water Management District and vicinity for May 2008. Potentiometric contours are based on water-level measurements collected at 567 wells during the period May 6-May 27, near the end of the dry season. Some contours are inferred from previous potentiometric-surface maps with larger well networks. The potentiometric surface of the carbonate Upper Floridan aquifer responds mainly to rainfall, and more locally, to ground-water withdrawals and spring flow. Potentiometric-surface highs generally correspond to topographic highs where the aquifer is recharged. Springs and areas of diffuse upward leakage naturally discharge water from the aquifer and are most prevalent along the St. Johns River. Areas of discharge are reflected by depressions in the potentiometric surface. Ground-water withdrawals locally have lowered the potentiometric surface. Ground water in the Upper Floridan aquifer generally flows from potentiometric highs to potentiometric lows in a direction perpendicular to the contours. Measured values of the potentiometric surface ranged from 7 feet below NGVD29 near Fernandina Beach, Florida, to 124 feet above NGVD29 in Polk County, Florida. The average water level of the network in May 2008 was about 1 foot lower than the average in September 2007 following below-average rainfall during the dry season of 2007-08. Seasonal differences in network average water levels generally range from 4 to 6 feet. For 457 wells with previous measurements, May 2008 levels ranged from about 19 feet below to about 11 feet above September 2007 water levels. The average water level of the network in May 2008 was about 1 foot higher than the average in May 2007. For 544 wells with previous measurements, May 2008 levels ranged from about 8 feet below to about 13 feet above May 2007 water levels. Long-term hydrographs of ground-water levels for continuous and periodic wells are available at internet site: http://waterdata.usgs.gov/fl/nwis/gw

Florida↗
USGS2007

Automated classifications of topography from DEMs by an unsupervised nested-means algorithm and a three-part geometric signature

An iterative procedure that implements the classification of continuous topography as a problem in digital image-processing automatically divides an area into categories of surface form; three taxonomic criteria–slope gradient, local convexity, and surface texture–are calculated from a square-grid digital elevation model (DEM). The sequence of programmed operations combines twofold-partitioned maps of the three variables converted to greyscale images, using the mean of each variable as the dividing threshold. To subdivide increasingly subtle topography, grid cells sloping at less than mean gradient of the input DEM are classified by designating mean values of successively lower-sloping subsets of the study area (nested means) as taxonomic thresholds, thereby increasing the number of output categories from the minimum 8 to 12 or 16. Program output is exemplified by 16 topographic types for the world at 1-km spatial resolution (SRTM30 data), the Japanese Islands at 270 m, and part of Hokkaido at 55 m. Because the procedure is unsupervised and reflects frequency distributions of the input variables rather than pre-set criteria, the resulting classes are undefined and must be calibrated empirically by subsequent analysis. Maps of the example classifications reflect physiographic regions, geological structure, and landform as well as slope materials and processes; fine-textured terrain categories tend to correlate with erosional topography or older surfaces, coarse-textured classes with areas of little dissection. In Japan the resulting classes approximate landform types mapped from airphoto analysis, while in the Americas they create map patterns resembling Hammond's terrain types or surface-form classes; SRTM30 output for the United States compares favorably with Fenneman's physical divisions. Experiments are suggested for further developing the method; the Arc/Info AML and the map of terrain classes for the world are available as online downloads.

Geomorphology↗
USGS2003

High-resolution topomapping of candidate MER landing sites with Mars Orbiter Camera narrow-angle images

We analyzed narrow‐angle Mars Orbiter Camera (MOC‐NA) images to produce high‐resolution digital elevation models (DEMs) in order to provide topographic and slope information needed to assess the safety of candidate landing sites for the Mars Exploration Rovers (MER) and to assess the accuracy of our results by a variety of tests. The mapping techniques developed also support geoscientific studies and can be used with all present and planned Mars‐orbiting scanner cameras. Photogrammetric analysis of MOC stereopairs yields DEMs with 3‐pixel (typically 10 m) horizontal resolution, vertical precision consistent with ∼0.22 pixel matching errors (typically a few meters), and slope errors of 1–3°. These DEMs are controlled to the Mars Orbiter Laser Altimeter (MOLA) global data set and consistent with it at the limits of resolution. Photoclinometry yields DEMs with single‐pixel (typically ∼3 m) horizontal resolution and submeter vertical precision. Where the surface albedo is uniform, the dominant error is 10–20% relative uncertainty in the amplitude of topography and slopes after “calibrating” photoclinometry against a stereo DEM to account for the influence of atmospheric haze. We mapped portions of seven candidate MER sites and the Mars Pathfinder site. Safety of the final four sites (Elysium, Gusev, Isidis, and Meridiani) was assessed by mission engineers by simulating landings on our DEMs of “hazard units” mapped in the sites, with results weighted by the probability of landing on those units; summary slope statistics show that most hazard units are smooth, with only small areas of etched terrain in Gusev crater posing a slope hazard.

Journal of Geophysical Research E: Planets↗
USGS2004

Potentiometric surface of the upper Floridan aquifer in the St. Johns River Water Management District and vicinity, Florida, May 2004

This map depicts the potentiometric surface of the Upper Floridan aquifer in the St. Johns River Water Management District and vicinity in May 2001. Potentiometric contours are based on water-level measurements collected at 684 wells during the period May 2 - 30, near the end of the dry season. The shapes of some contours have been inferred from previous potentiometric-surface maps with larger well networks. The potentiometric surface of the carbonate Upper Floridan aquifer responds mainly to rainfall, and more locally, to ground-water withdrawals. Potentiometric-surface highs generally correspond to topographic highs where the aquifer is recharged. Springs and areas of diffuse upward leakage naturally discharge water from the aquifer and are most prevalent along the St. Johns River. Areas of discharge are reflected by depressions in the potentiometric surface. Ground-water withdrawals locally have lowered the potentiometric surface. Ground water in the Upper Floridan aquifer generally flows from potentiometric highs to potentiometric lows in a direction perpendicular to the contours.

Florida↗
USGS2005

Potentiometric surface of the upper Floridan aquifer in the St. Johns River Water Management District and vicinity, Florida, September 2004

Introduction: This map depicts the potentiometric surface of the Upper Floridan aquifer in the St. Johns River Water Management District and vicinity in September 2004. Potentiometric contours are based on water-level measurements collected at 608 wells during the period September 14-October 1, near the end of the wet season. The shapes of some contours have been inferred from previous potentiometric-surface maps with larger well networks. The potentiometric surface of the carbonate Upper Floridan aquifer responds mainly to rainfall, and more locally, to ground-water withdrawals. Potentiometric-surface highs generally correspond to topographic highs where the aquifer is recharged. Springs and areas of diffuse upward leakage naturally discharge water from the aquifer and are most prevalent along the St. Johns River. Areas of discharge are reflected by depressions in the potentiometric surface. Ground-water withdrawals locally have lowered the potentiometric surface. Ground water in the Upper Floridan aquifer generally flows from potentiometric highs to potentiometric lows in a direction perpendicular to the contours.

Florida↗