Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Hydrogeology Journal”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6Linked to original sources
USGS2011

Review: Regional land subsidence accompanying groundwater extraction

The extraction of groundwater can generate land subsidence by causing the compaction of susceptible aquifer systems, typically unconsolidated alluvial or basin-fill aquifer systems comprising aquifers and aquitards. Various ground-based and remotely sensed methods are used to measure and map subsidence. Many areas of subsidence caused by groundwater pumping have been identified and monitored, and corrective measures to slow or halt subsidence have been devised. Two principal means are used to mitigate subsidence caused by groundwater withdrawal—reduction of groundwater withdrawal, and artificial recharge. Analysis and simulation of aquifer-system compaction follow from the basic relations between head, stress, compressibility, and groundwater flow and are addressed primarily using two approaches—one based on conventional groundwater flow theory and one based on linear poroelasticity theory. Research and development to improve the assessment and analysis of aquifer-system compaction, the accompanying subsidence and potential ground ruptures are needed in the topic areas of the hydromechanical behavior of aquitards, the role of horizontal deformation, the application of differential synthetic aperture radar interferometry, and the regional-scale simulation of coupled groundwater flow and aquifer-system deformation to support resource management and hazard mitigation measures.

Hydrogeology Journal↗
USGS2011

Cross-borehole flow analysis to characterize fracture connections in the Melechov Granite, Bohemian-Moravian Highland, Czech Republic

Application of the cross-borehole flow method, in which short pumping cycles in one borehole are used to induce time-transient flow in another borehole, demonstrated that a simple hydraulic model can characterize the fracture connections in the bedrock mass between the two boreholes. The analysis determines the properties of fracture connections rather than those of individual fractures intersecting a single borehole; the model contains a limited number of adjustable parameters so that any correlation between measured and simulated flow test data is significant. The test was conducted in two 200-m deep boreholes spaced 21 m apart in the Melechov Granite in the Bohemian-Moravian Highland, Czech Republic. Transient flow was measured at depth stations between the identified transmissive fractures in one of the boreholes during short-term pumping and recovery periods in the other borehole. Simulated flows, based on simple model geometries, closely matched the measured flows. The relative transmissivity and storage of the inferred fracture connections were corroborated by tracer testing. The results demonstrate that it is possible to assess the properties of a fracture flow network despite being restricted to making measurements in boreholes in which a local population of discrete fractures regulates the hydraulic communication with the larger-scale aquifer system.

Bohemian-moravian Highland↗
USGS2011

Editor’s message: Groundwater modeling fantasies - Part 1, adrift in the details

Fools ignore complexity. Pragmatists suffer it. Some can avoid it. Geniuses remove it. …Simplicity does not precede complexity, but follows it. ( Epigrams in Programming by Alan Perlis, a computer scientist; Perlis 1982 ). A doctoral student creating a groundwater model of a regional aquifer put individual circular regions around data points where he had hydraulic head measurements, so that each region’s parameter values could be adjusted to get perfect fit with the measurement at that point. Nearly every measurement point had its own parameter-value region. After calibration, the student was satisfied because his model correctly reproduced all of his data. Did he really get the true field values of parameters in this manner? Did this approach result in a realistic, meaningful and useful groundwater model?—truly doubtful. Is this story a sign of a common style of educating hydrogeology students these days? Where this is the case, major changes are needed to add back ‘common-sense hydrogeology’ to the curriculum. Worse, this type of modeling approach has become an industry trend in application of groundwater models to real systems, encouraged by the advent of automatic model calibration software that has no problem providing numbers for as many parameter value estimates as desired. Just because a computer program can easily create such values does not mean that they are in any sense useful—but unquestioning practitioners are happy to follow such software developments, perhaps because of an implied promise that highly parameterized models, here referred to as ‘complex’, are somehow superior. This and other fallacies are implicit in groundwater modeling studies, most usually not acknowledged when presenting results. This two-part Editor’s Message deals with the state of groundwater modeling: part 1 (here) focuses on problems and part 2 (Voss 2011 ) on prospects.

Hydrogeology Journal↗
USGS2011

Editor’s message: Groundwater modeling fantasies - Part 2, down to earth

Simplicity is the final achievement. After one has played a vast quantity of notes and more notes, it is simplicity that emerges as the crowning reward of art. (Frédéric Chopin, a musician and composer, quoted in If Not God, Then What? by Fost 2007 ) Despite the dubious developments discussed in part 1 of this Editor’s Message (Voss 2011 ), groundwater modeling really does represent the state of the art in hydrogeology, and groundwater modeling is in fact one of our most powerful tools for enhancing hydrogeologic understanding and for informing management of subsurface resources, at least when in the hands of competent hydrologists.

Hydrogeology Journal↗
USGS2012

Comparison of particle-tracking and lumped-parameter age-distribution models for evaluating vulnerability of production wells to contamination

Environmental age tracers have been used in various ways to help assess vulnerability of drinking-water production wells to contamination. The most appropriate approach will depend on the information that is available and that which is desired. To understand how the well will respond to changing nonpoint-source contaminant inputs at the water table, some representation of the distribution of groundwater ages in the well is needed. Such information for production wells is sparse and difficult to obtain, especially in areas lacking detailed field studies. In this study, age distributions derived from detailed groundwater-flow models with advective particle tracking were compared with those generated from lumped-parameter models to examine conditions in which estimates from simpler, less resource-intensive lumped-parameter models could be used in place of estimates from particle-tracking models. In each of four contrasting hydrogeologic settings in the USA, particle-tracking and lumped-parameter models yielded roughly similar age distributions and largely indistinguishable contaminant trends when based on similar conceptual models and calibrated to similar tracer data. Although model calibrations and predictions were variably affected by tracer limitations and conceptual ambiguities, results illustrated the importance of full age distributions, rather than apparent tracer ages or model mean ages, for trend analysis and forecasting.

Hydrogeology Journal↗
USGS2012

Uranium isotopes (234U/238U) in rivers of the Yukon Basin (Alaska and Canada) as an aid in identifying water sources, with implications for monitoring hydrologic change in arctic regions

The ability to detect hydrologic variation in large arctic river systems is of major importance in understanding and predicting effects of climate change in high-latitude environments. Monitoring uranium isotopes ( 234 U and 238 U) in river water of the Yukon River Basin of Alaska and northwestern Canada (2001–2005) has enhanced the ability to identify water sources to rivers, as well as detect flow changes that have occurred over the 5-year study. Uranium isotopic data for the Yukon River and major tributaries (the Porcupine and Tanana rivers) identify several sources that contribute to river flow, including: deep groundwater, seasonally frozen river-valley alluvium groundwater, and high-elevation glacial melt water. The main-stem Yukon River exhibits patterns of uranium isotopic variation at several locations that reflect input from ice melt and shallow groundwater in the spring, as well as a multi-year pattern of increased variability in timing and relative amount of water supplied from higher elevations within the basin. Results of this study demonstrate both the utility of uranium isotopes in revealing sources of water in large river systems and of incorporating uranium isotope analysis in long-term monitoring of arctic river systems that attempt to assess the effects of climate change.

Yukon Basin↗
USGS2012

Heterogeneous redox conditions, arsenic mobility, and groundwater flow in a fractured-rock aquifer near a waste repository site in New Hampshire, USA

Anthropogenic sources of carbon from landfill or waste leachate can promote reductive dissolution of in situ arsenic (As) and enhance the mobility of As in groundwater. Groundwater from residential-supply wells in a fractured crystalline-rock aquifer adjacent to a Superfund site in Raymond, New Hampshire, USA, showed evidence of locally enhanced As mobilization in relatively reducing (mixed oxic-anoxic to anoxic) conditions as determined by redox classification and other lines of evidence. Redox classification was determined from geochemical indicators based on threshold concentrations of dissolved oxygen (DO), nitrate (NO 3- ), iron (Fe 2+ ), manganese (Mn 2+ ), and sulfate (SO 4 2- ). Redox conditions were evaluated also based on methane (CH 4 ), excess nitrogen gas (N 2 ) from denitrification, the oxidation state of dissolved As speciation (As(III) and As(V)), and several stable isotope ratios. Samples from the residential-supply wells primarily exhibit mixed redox conditions, as most have long open boreholes (typically 50–100 m) that receive water from multiple discrete fractures with contrasting groundwater chemistry and redox conditions. The methods employed in this study can be used at other sites to gauge redox conditions and the potential for As mobilization in complex fractured crystalline-rock aquifers where multiple lines of evidence are likely needed to understand As occurrence, mobility, and transport.

New Hampshire↗
USGS2012

Old groundwater in parts of the upper Patapsco aquifer, Atlantic Coastal Plain, Maryland, USA: Evidence from radiocarbon, chlorine-36 and helium-4

Apparent groundwater ages along two flow paths in the upper Patapsco aquifer of the Maryland Atlantic Coastal Plain, USA, were estimated using 14 C, 36 Cl and 4 He data. Most of the ages range from modern to about 500 ka, with one sample at 117 km downgradient from the recharge area dated by radiogenic 4 He accumulation at more than one Ma. Last glacial maximum (LGM) water was located about 20 km downgradient on the northern flow path, where the radiocarbon age was 21.5 ka, paleorecharge temperatures were 0.5–1.5 °C (a maximum cooling of about 12 °C relative to the modern mean annual temperature of 13 °C), and Cl – , Cl/Br, and stable isotopes of water were minimum. Low recharge temperatures (typically 5–7 °C) indicate that recharge occurred predominantly during glacial periods when coastal heads were lowest due to low sea-level stand. Flow velocities averaged about 1.0 m a –1 in upgradient parts of the upper Patapsco aquifer and decreased from 0.13 to 0.04 m a –1 at 40 and 80 km further downgradient, respectively. This study demonstrates that most water in the upper Patapsco aquifer is non-renewable on human timescales under natural gradients, thus highlighting the importance of effective water-supply management to prolong the resource.

Maryland↗
USGS2012

Sensitivity analysis of lake mass balance in discontinuous permafrost: the example of disappearing Twelvemile Lake, Yukon Flats, Alaska (USA)

Many lakes in northern high latitudes have undergone substantial changes in surface area over the last four decades, possibly as a result of climate warming. In the discontinuous permafrost of Yukon Flats, interior Alaska (USA), these changes have been non-uniform across adjacent watersheds, suggesting local controls on lake water budgets. Mechanisms that could explain the decreasing mass of one lake in Yukon Flats since the early 1980s, Twelvemile Lake, are identified via a scoping analysis that considers plausible changes in snowmelt mass and infiltration, permafrost distribution, and climate warming. Because predicted changes in evaporation (2 cmyr -1 ) are inadequate to explain the observed 17.5 cmyr -1 reduction in mass balance, other mechanisms are required. The most important potential mechanisms are found to involve: (1) changes in shallow, lateral groundwater flow to the lake possibly facilitated by vertical freeze-thaw migration of the permafrost table in gravel; (2) increased loss of lake water as downward groundwater flow through an open talik to a permeable subpermafrost flowpath; and (3) reduced snow meltwater inputs due to decreased snowpack mass and increased infiltration of snowmelt into, and subsequent evaporation from, fine-grained sediment mantling the permafrost-free lake basin.

Alaska↗
USGS2012

Rapid runoff via shallow throughflow and deeper preferential flow in a boreal catchment underlain by frozen silt (Alaska, USA)

In high-latitude catchments where permafrost is present, runoff dynamics are complicated by seasonal active-layer thaw, which may cause a change in the dominant flowpaths as water increasingly contacts mineral soils of low hydraulic conductivity. A 2-year study, conducted in an upland catchment in Alaska (USA) underlain by frozen, well-sorted eolian silt, examined changes in infiltration and runoff with thaw. It was hypothesized that rapid runoff would be maintained by flow through shallow soils during the early summer and deeper preferential flow later in the summer. Seasonal changes in soil moisture, infiltration, and runoff magnitude, location, and chemistry suggest that transport is rapid, even when soils are thawed to their maximum extent. Between June and September, a shift occurred in the location of runoff, consistent with subsurface preferential flow in steep and wet areas. Uranium isotopes suggest that late summer runoff erodes permafrost, indicating that substantial rapid flow may occur along the frozen boundary. Together, throughflow and deep preferential flow may limit upland boreal catchment water and solute storage, and subsequently biogeochemical cycling on seasonal to annual timescales. Deep preferential flow may be important for stream incision, network drainage development, and the release of ancient carbon to ecosystems

Alaska↗
USGS2013

Review: groundwater in Alaska (USA)

Groundwater in the US state of Alaska is critical to both humans and ecosystems. Interactions among physiography, ecology, geology, and current and past climate have largely determined the location and properties of aquifers as well as the timing and magnitude of fluxes to, from, and within the groundwater system. The climate ranges from maritime in the southern portion of the state to continental in the Interior, and arctic on the North Slope. During the Quaternary period, topography and rock type have combined with glacial and periglacial processes to develop the unconsolidated alluvial aquifers of Alaska and have resulted in highly heterogeneous hydrofacies. In addition, the long persistence of frozen ground, whether seasonal or permanent, greatly affects the distribution of aquifer recharge and discharge. Because of high runoff, a high proportion of groundwater use, and highly variable permeability controlled in part by permafrost and seasonally frozen ground, understanding groundwater/surface-water interactions and the effects of climate change is critical for understanding groundwater availability and the movement of natural and anthropogenic contaminants.

Alaska↗
USGS2013

Impacts of climate, lake size, and supra- and sub-permafrost groundwater flow on lake-talik evolution, Yukon Flats, Alaska (USA)

In cold regions, hydrologic systems possess seasonal and perennial ice-free zones (taliks) within areas of permafrost that control and are enhanced by groundwater flow. Simulation of talik development that follows lake formation in watersheds modeled after those in the Yukon Flats of interior Alaska (USA) provides insight on the coupled interaction between groundwater flow and ice distribution. The SUTRA groundwater simulator with freeze–thaw physics is used to examine the effect of climate, lake size, and lake–groundwater relations on talik formation. Considering a range of these factors, simulated times for a through-going sub-lake talik to form through 90 m of permafrost range from ∼200 to > 1,000 years (vertical thaw rates < 0.1–0.5 m yr −1 ). Seasonal temperature cycles along lake margins impact supra-permafrost flow and late-stage cryologic processes. Warmer climate accelerates complete permafrost thaw and enhances seasonal flow within the supra-permafrost layer. Prior to open talik formation, sub-lake permafrost thaw is dominated by heat conduction. When hydraulic conditions induce upward or downward flow between the lake and sub-permafrost aquifer, thaw rates are greatly increased. The complexity of ground-ice and water-flow interplay, together with anticipated warming in the arctic, underscores the utility of coupled groundwater-energy transport models in evaluating hydrologic systems impacted by permafrost.

Alaska↗
USGS2013

Permafrost thaw in a nested groundwater-flow system

Groundwater flow in cold regions containing permafrost accelerates climate-warming-driven thaw and changes thaw patterns. Simulation analyses of groundwater flow and heat transport with freeze/thaw in typical cold-regions terrain with nested flow indicate that early thaw rate is particularly enhanced by flow, the time when adverse environmental impacts of climate-warming-induced permafrost loss may be severest. For the slowest climate-warming rate predicted by the Intergovernmental Panel on Climate Change (IPCC), once significant groundwater flow begins, thick permafrost layers can vanish in several hundred years, but survive over 1,000 years where flow is minimal. Large-scale thaw depends mostly on the balance of heat advection and conduction in the supra-permafrost zone. Surface-water bodies underlain by open taliks allow slow sub-permafrost flow, with lesser influence on regional thaw. Advection dominance over conduction depends on permeability and topography. Groundwater flow around permafrost and flow through permafrost impact thaw differently; the latter enhances early thaw rate. Air-temperature seasonality also increases early thaw. Hydrogeologic heterogeneity and topography strongly affect thaw rates/patterns. Permafrost controls the groundwater/surface-water-geomorphology system; hence, prediction and mitigation of impacts of thaw on ecology, chemical exports and infrastructure require improved hydrogeology/permafrost characterization and understanding

Hydrogeology Journal↗
USGS2013

Estimating hydraulic properties from tidal attenuation in the Northern Guam Lens Aquifer, territory of Guam, USA

Tidal-signal attenuations are analyzed to compute hydraulic diffusivities and estimate regional hydraulic conductivities of the Northern Guam Lens Aquifer, Territory of Guam (Pacific Ocean), USA. The results indicate a significant tidal-damping effect at the coastal boundary. Hydraulic diffusivities computed using a simple analytical solution for well responses to tidal forcings near the periphery of the island are two orders of magnitude lower than for wells in the island’s interior. Based on assigned specific yields of ~0.01–0.4, estimated hydraulic conductivities are ~20–800 m/day for peripheral wells, and ~2,000–90,000 m/day for interior wells. The lower conductivity of the peripheral rocks relative to the interior rocks may best be explained by the effects of karst evolution: (1) dissolutional enhancement of horizontal hydraulic conductivity in the interior; (2) case-hardening and concurrent reduction of local hydraulic conductivity in the cliffs and steeply inclined rocks of the periphery; and (3) the stronger influence of higher-conductivity regional-scale features in the interior relative to the periphery. A simple numerical model calibrated with measured water levels and tidal response estimates values for hydraulic conductivity and storage parameters consistent with the analytical solution. The study demonstrates how simple techniques can be useful for characterizing regional aquifer properties.

Hydrogeology Journal↗
USGS2013

Uncertainty in simulated groundwater-quality trends in transient flow

In numerical modeling of groundwater flow, the result of a given solution method is affected by the way in which transient flow conditions and geologic heterogeneity are simulated. An algorithm is demonstrated that simulates breakthrough curves at a pumping well by convolution-based particle tracking in a transient flow field for several synthetic basin-scale aquifers. In comparison to grid-based (Eulerian) methods, the particle (Lagrangian) method is better able to capture multimodal breakthrough caused by changes in pumping at the well, although the particle method may be apparently nonlinear because of the discrete nature of particle arrival times. Trial-and-error choice of number of particles and release times can perhaps overcome the apparent nonlinearity. Heterogeneous aquifer properties tend to smooth the effects of transient pumping, making it difficult to separate their effects in parameter estimation. Porosity, a new parameter added for advective transport, can be accurately estimated using both grid-based and particle-based methods, but predictions can be highly uncertain, even in the simple, nonreactive case.

Hydrogeology Journal↗
USGS2013

Comparison of age distributions estimated from environmental tracers by using binary-dilution and numerical models of fractured and folded karst: Shenandoah Valley of Virginia and West Virginia, USA

Measured concentrations of environmental tracers in spring discharge from a karst aquifer in the Shenandoah Valley, USA, were used to refine a numerical groundwater flow model. The karst aquifer is folded and faulted carbonate bedrock dominated by diffuse flow along fractures. The numerical model represented bedrock structure and discrete features (fault zones and springs). Concentrations of 3 H, 3 He, 4 He, and CFC-113 in spring discharge were interpreted as binary dilutions of young (0–8 years) water and old (tracer-free) water. Simulated mixtures of groundwater are derived from young water flowing along shallow paths, with the addition of old water flowing along deeper paths through the model domain that discharge to springs along fault zones. The simulated median age of young water discharged from springs (5.7 years) is slightly older than the median age estimated from 3 H/ 3 He data (4.4 years). The numerical model predicted a fraction of old water in spring discharge (0.07) that was half that determined by the binary-dilution model using the 3 H/ 3 He apparent age and 3 H and CFC-113 data (0.14). This difference suggests that faults and lineaments are more numerous or extensive than those mapped and included in the numerical model.

Virginia;West Virginia↗
USGS2013

Comparison of a karst groundwater model with and without discrete conduit flow

Karst aquifers exhibit a dual flow system characterized by interacting conduit and matrix domains. This study evaluated the coupled continuum pipe-flow framework for modeling karst groundwater flow in the Madison aquifer of western South Dakota (USA). Coupled conduit and matrix flow was simulated within a regional finite-difference model over a 10-year transient period. An existing equivalent porous medium (EPM) model was modified to include major conduit networks whose locations were constrained by dye-tracing data and environmental tracer analysis. Model calibration data included measured hydraulic heads at observation wells and estimates of discharge at four karst springs. Relative to the EPM model, the match to observation well hydraulic heads was substantially improved with the addition of conduits. The inclusion of conduit flow allowed for a simpler hydraulic conductivity distribution in the matrix continuum. Two of the high-conductivity zones in the EPM model, which were required to indirectly simulate the effects of conduits, were eliminated from the new model. This work demonstrates the utility of the coupled continuum pipe-flow method and illustrates how karst aquifer model parameterization is dependent on the physical processes that are simulated.

South Dakota↗