Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Coastal Engineering”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

194 records · Page 6Linked to original sources
USGS1996

Pesticides in surface water from three agricultural basins in south-central Georgia, 1993-97

Twenty-two of 43 pesticides analyzed were detected in 128 water samples collected from the Tucsawhatchee Creek, the Little River, and the Withlacoochee River. These streams drain agricultural basins in south-central Georgia and were sampled from March 1993 through June 1995. Herbicides were detected more frequently than insecticides. The most frequently detected herbicides were atrazine and metolachlor and the most frequently detected insecticide was carbaryl. Pesticide concentrations in the three streams were low and did not exceed U.S. Environmental Protection Agency drinking water standards. The maximum pesticide concentration was 2.6 mg/L (micrograms per liter) for propargite, a miticide detected in only one sample. The maximum concentrations of the remaining 21 pesticides were less than 0.25 mg/L. The median concentrations were equal to the method detection limit for all pesticides except atrazine (0.008 mg/L) and metolachlor (0.012 mg/L). The ratio of herbicide detections to nondetections was largest in the planting season, smaller in the harvest season and smallest in the fallow season for the three basins. The same pattern existed for the insecticide ratios in the Little River and the Withlacoochee River. Pairwise correlations between concentrations of atrazine and metolachlor, and four parameters (discharge, and concentrations of dissolved organic carbon, suspended organic carbon, and suspended sediment) were evaluated for each stream. The strongest correlations existed between metolachlor and mean daily discharge, and metolachlor and sediment in the Withlacoochee River. The only significant correlation for the Little River was between atrazine and suspended sediment.

Georgia↗
USGS2026

Assessing environmental drivers of denitrification in restored riverine floodplains

Restoration of impaired floodplains is an increasingly prevalent strategy for alleviating water quality concerns and reducing downstream flooding at watershed scales. Floodplains temporarily store water and slow flow velocity to promote sedimentation during overbank flooding and remove inorganic nitrogen from floodwater and groundwater via denitrification. Evaluating the impacts of different restoration strategies on denitrification can inform more strategic investments into floodplain modifications that improve water quality outcomes. Our research investigates how denitrification rates in floodplains respond to environmental factors that are actionable from an engineering perspective through design and water resources management. We seasonally measured soil denitrification enzyme activity and various environmental characteristics in 4 floodplains with different restoration design and management approaches at the confluence of the Wabash and Tippecanoe Rivers in Indiana, United States. Our results showed that denitrification rates in an agricultural floodplain were significantly lower than in restored floodplains with native vegetation. Certain soil conditions characteristic of floodplain wetlands were associated with higher denitrification, particularly elevated total nitrogen, moisture, silt, and organic matter contents. Vegetation species composition was correlated with denitrification rates. This link may reflect the direct effects of vegetation on soil conditions, such as supplying labile organic carbon, or indirect effects, such as vegetation acting as an indicator of hydrologic regime and land use. Denitrification seasonally varied, peaking in winter when nitrate supply from rivers draining agricultural watersheds in the region is also high. Substrate limitation of soil denitrification enzyme activity was most significant during the summer when overbank flooding, which replenishes soil nitrogen stocks, rarely occurs. Our findings indicate that denitrification capacity will likely be maximized in riverine floodplains that are restored as wetlands with diverse native vegetation and enhanced hydrologic connectivity. Such restoration activities promote higher denitrification rates via elevated moisture, fine sediment deposition, and soil organic matter.

Tippecanoe River, Wabash River↗
USGS2024

Framework for mapping liquefaction hazard–Targeted design ground motions

Liquefaction-induced ground failure poses substantial challenges to geotechnical earthquake engineering design. Current approaches for designing against liquefaction hazards, as specified in most seismic provisions, focus on estimating a liquefaction factor of safety ( 𝐹⁢𝑆𝐿 ) and typically characterize earthquake loading using design parameters based on probabilistic or deterministic ground motion levels. Because 𝐹⁢𝑆𝐿 is estimated deterministically, this basis of design neglects considerable uncertainties for estimating liquefaction triggering and its consequences and results in a lack of liquefaction-specific design criteria, particularly as structural design has advanced toward risk-targeted performance objectives. This study presents a framework for developing liquefaction-targeted design criteria based on a minimum acceptable return period of liquefaction, informed by probabilistic liquefaction hazard analysis (PLHA). PLHA quantifies annualized rates of liquefaction by considering contributions from (1) the full ground-motion probability space, and (2) uncertainties in liquefaction triggering using probabilistic models. PLHA is used in this study to characterize the current, effective return periods of 𝐹⁢𝑆𝐿 ( 𝑇𝑅,𝐹⁢𝑆 ) obtained from conventional liquefaction hazard analysis (CLHA) using uniform-hazard ground motions. 𝑇𝑅,𝐹⁢𝑆 is evaluated in a parametric study of nearly 100 sites throughout the conterminous United States. The results indicate large geographic variations in acceptable liquefaction hazard levels, with implied 𝑇𝑅,𝐹⁢𝑆 ranging between approximately 1,000 to 3,000 years. To address these inconsistencies without the computational demands of full PLHA, a framework is proposed for developing a liquefaction-targeted design peak ground acceleration, 𝑃⁢𝐺⁢𝐴𝐿 , for use in liquefaction models that result in consistent liquefaction design levels across all geographic locations. The mapped 𝑃⁢𝐺⁢𝐴𝐿 is shown to be somewhat sensitive to site-specific properties, and adjustment factors are developed and presented. The proposed 𝑃⁢𝐺⁢𝐴𝐿 mapping procedure produces 𝐹⁢𝑆𝐿 estimates that are consistent with those obtained from full PLHA at a target 𝑇𝑅,𝐹⁢𝑆 , providing a promising roadmap to incorporating PLHA concepts into current liquefaction design methods.

Journal of Geotechnical and Geoenvironmental Engin↗
USGS2026

From landslide susceptibility to risk assessment in the conterminous U.S.

Understanding the spatial distribution of landslide prone-areas and what consequences they may have is important for risk management and land-use planning. In the United States, although landslides occur in every state, a comprehensive landslide risk assessment is still missing. Existing efforts, such as the Federal Emergency Management Agency (FEMA)’s National Risk Index, rely on aggregated products and coarse cartographic units, limiting their geomorphological and practical accuracy. In this study, we present a methodological advance for landslide risk assessment across large areas with incomplete and sparse data. We apply our procedures to the conterminous United States by integrating geomorphologically meaningful partitions and spatial and temporal probability data-driven models. Landslide susceptibility is estimated using a Generalized Additive Mixed Model incorporating a bias capture/correction scheme to account for inventory inaccuracies (reference Area Under the Curve = 0.75). The exceedance probabilities of landslide occurrence are defined for three temporal scenarios (2, 5, and 10 year). Then, we explore the associated potential economic consequences for human settlements and agricultural areas. The findings indicate that the spatial variability of risk is primarily controlled by exposure rather than by susceptibility/hazard alone. The mean risk increases by ∼170% from the 2-year to the 10-year scenario. Beyond its quantitative outcomes, this study offers a blueprint for continental or sub-continental scale landslide risk assessments, demonstrating both the opportunities and current limitations.

Engineering Geology↗
USGS2025

Global patterns of coseismic landslide runout mobility differ from aseismic landslide trends

Coseismic landslides significantly contribute to human and economic losses during and immediately following earthquakes, yet very little data on the runout of such landslides exist. While well-established behavior of aseismic (e.g., hydrologically triggered) landslide runout mobility suggests strong correlation between landslide size and mobility, limited studies of coseismic landslide runout find conflicting mobility trends. We present a global dataset of runout lengths produced from a new automated method for estimating landslide runout, developed and validated using 1726 manually mapped landslides from five unique earthquakes. We then apply the automated runout tool to 23 global earthquake-induced landslide inventories, producing a compiled database of 73,665 measured and estimated runout lengths of coseismic landslides to assess mobility trends. We find a significant divergence between well-established aseismic mobility trends and that of coseismic landslides, with far greater scatter and more complex mobility patterns in earthquake-triggered landslides. As a function of landslide size, we observe global coseismic landslide mobility patterns are bilinear, becoming increasingly less mobile with increasing size above some threshold. This discordance between aseismic and coseismic landslide mobility may be a function of landslide type, kinematics, hydrology, and or setting that systematically differ between triggering mechanisms and should be explored in more depth to develop predictive models of these unique runout patterns. These results suggest hazard and risk models for coseismic landslides may significantly under-predict or over-predict impacts, depending on the size of triggered landslides.

Engineering Geology↗
USGS2026

PFAS remediation in a bioelectrochemical system inoculated with the west branch consortium (WBC-2)

Groundwater contamination by per - and polyfluoroalkyl substances (PFAS) poses a persistent environmental and public health concern. This study evaluates a two-chambered bioelectrochemical system (BES) inoculated with the West Branch Consortium (WBC-2) for PFAS remediation. Under an applied cathodic potential of −450 mV (versus Ag/AgCl), the BES with active WBC-2 achieved >99.0% perfluorooctanesulfonic acid (PFOS) removal within 21 days in deionized water with culture medium and > 98.9% removal of PFOS, perfluorooctanoic acid (PFOA), perfluorohexanoic acid (PFHxA), and perfluorohexanesulfonic acid (PFHxS) in contaminated groundwater after 102 days. Intermediate formation (e.g., PFOA, 6:2 fluorotelomer sulfonate (6:2 FTS), perfluoropropionic acid (PFPrA), perfluorobutanoic acid (PFBA)) and background-corrected fluoride release were consistent with PFOS transformation under anaerobic reducing conditions potentially involving defluorination. Following repeated PFOS spikes (100 μg/L on Days 0, 50, and 399), PFOA, PFPrA, and PFBA accumulated over 664 days. Despite being the dominant accumulated compound, PFOA accounted for <1.8% of the total spiked PFOS mass. Minimal PFOS transformation occurred in controls without active WBC-2, highlighting the importance of microbial metabolism. Biofilm analysis revealed dense colonization of rod-shaped bacteria on carbon fiber brushes. Enrichment of Bacillus , Agrobacterium , and other low-abundance taxa suggests selective adaptation to BES and PFAS conditions. These findings highlight BES driven by electrochemically stimulated microbial activity as a promising strategy for PFAS remediation.

Journal of Water Process Engineering↗
USGS2026

Tracking baseflow supply dynamics using SWOT data from small groundwater-dominated lakes

In situ surface-water monitoring strategies are biased towards larger perennial streams and lakes and are generally not designed to track mechanisms of baseflow supply contributed by the dynamic storage of aquifers. Additionally, small (< 1 km 2 ) groundwater-influenced lakes and wetlands globally have little in situ monitoring infrastructure. We explored the utility of remotely sensed Surface Water Ocean Topography Satellite (SWOT) data, collected from 2023 onward, to characterise the seasonal and multi-year water-level trends of groundwater flow-through kettle lakes distributed across the permeable sediments of eastern Massachusetts, USA. This analysis indicated that water levels for kettle lakes with areas down to approximately 0.05 km 2 are resolvable in the study area. Our examination of 17 kettle lakes found that SWOT water-surface elevation data closely tracked groundwater levels in adjacent monitoring wells where available, including the timing of seasonal patterns (highest levels generally in late spring), although there was some variation between years and there was a substantial lag in the timing of high water levels for a lake located downgradient from a 30-m-thick vadose zone. Furthermore, SWOT-observed water-level increases in kettle lakes tracked with baseflow increases in two adjacent groundwater-dominated streams, as would be expected from increased hydraulic gradients. Unlike spectral remote sensing, SWOT data are generally not affected by cloud cover, resulting in a potential for groundwater-dominated lakes to be sentinels of dynamic storage patterns, including identification of baseflow drought lags, which are currently ill-defined hydrological processes. SWOT monitoring of groundwater-influenced surface waters shows potential for augmenting existing monitoring wells and streamgages as continuous monitors of groundwater levels and baseflow supply in permeable terrain.

Massachusetts↗
USGS2025

Combining multisite tsunami and deformation modeling to constrain slip distributions for the 1700 C.E. Cascadia earthquake

A major earthquake ruptured the Cascadia subduction zone (CSZ) on 26 January 1700. Key paleoseismic evidence associated with this event include tsunami deposits, stratigraphic evidence of coastal coseismic subsidence, written Japanese records of a tsunami unaccompanied by earthquake shaking, and margin‐wide turbidites found offshore and in lacustrine environments. Despite this wealth of independent clues, important details about this event remain unresolved. Dating uncertainties do not conclusively establish whether the proxies are from one earthquake or a sequence of them, and we have limited knowledge of the likely slip distributions of the event or events. Here, we use a catalog of 37,500 candidate synthetic ruptures between M w 7.8 and 9.2 and simulate their resulting coseismic deformation and tsunami inundation. Each model is then compared against estimated Japan tsunami arrivals, regional coastal subsidence records, and local paleotsunami deposits mapped at six different coastal marshes and one coastal lake along the CSZ. We find that seven full‐margin ruptures with a median magnitude of M w 9.1 satisfy all three constraints. We favor one M w 9.11 model that best matches all site paleoseismic observations and suggests that the Cascadia megathrust slipped up to ∼30 m and must have shallow geodetic coupling. We also find that some sequences composed of three or four ruptures can still satisfy the observations, yet no sequences of two ruptures can. Sequences are differentiated into three groups based on whether they contain a mainshock rupture located in the south (>44° N) or further north. All sequences contain unruptured portions of the megathrust and most contain mainshocks with peak slip above 40 m. The fit of the geologic evidence from sequences is poor in comparison to single‐event models. Therefore, sequences are generally less favored compared to full‐margin events.

British Columbia, California, Oregon, Washington↗
USGS2026

Discrete element investigation of the influence of shallow soil density on the manifestations of strike-slip surface fault rupture

This study investigates the influence of soil relative density on strike-slip surface fault rupture manifestations using three-dimensional numerical simulations performed with the discrete element method (DEM). The simulations capture the formation of distinctive fault strands within complex flower structures using tens of millions of grains. The tendency for dense soils to localize shear manifests as multiple localized shear bands within wide zones of deformation in strike-slip fault rupture, whereas diffuse shear deformation develops within narrow zones in loose soils. The spatial extents of soil deformation are consistent between simulations having similar relative densities but with different quantities of grains. However, individual shears are more distinguishable in assemblages of finer grains than in assemblages of coarser grains. The simulations show the progressive development of new shears within the bounds of previously developed shears. Shear activity transitions inward as fault activity diminishes along the outermost shears and continues along newly developed shears until a vertically dipping throughgoing shear structure develops that accommodates most of the fault displacement thereon. The throughgoing fault develops at smaller fault displacements in looser soils because the first shear rupture propagates closer to the vertical direction and does not undergo as much inward translation of shear activity, as is observed in denser soils. In all simulations, ground surface uplift develops between nonintersecting active shears, and ground surface subsidence tends to develop where new shears intersect previous shears. The surface traces in these simulations are shown to be consistent with analog models and case histories of surface fault rupture occurring in different shallow subsurface materials. Although computationally costly, these modeling results are valuable for providing a strong numerical supplement to traditional analog models used to represent the mechanics of strike-slip zones in soil, and they provide quantifiable stresses and large-strain deformations throughout the model domain.

Journal of Geotechnical and Geoenvironmental Engin↗
USGS2026

Spatio-temporal modeling for assessing geoenergy resources: A workflow applied to gas in place variation in coal beds

The ability to estimate spatio-temporal changes in hydrocarbon reservoir properties and energy resources within pore volumes is essential for optimizing production, reservoir management, geologic energy storage, and safety in underground mining operations. In coal seams, predicting remaining methane gas-in-place (GIP) is critical for quantifying producible gas and improving mine safety and productivity through effective ventilation planning. Although such changes are commonly evaluated using physics-based numerical simulation models, these approaches often require extensive data, calibration effort, and time. This study presents a spatio-temporal geostatistical modeling approach that bridges the gap between purely spatial models and full numerical simulations. The method is applied to a case study of coal seam degasification in the Mary Lee coal group, Black Warrior Basin, Alabama, USA, to estimate GIP evolution over time within a selected mining district. The analysis uses published data from prior natural gas production history-matching of degasification using vertical wells. Empirical spatial and temporal statistics were calculated for reservoir pressure and water saturation, and spatio-temporal variogram models were fitted to experimental variograms. These models provided the structural basis for spatio-temporal kriging, integrated with spatial estimates of time-invariant parameters (porosity, density, and thickness) to estimate GIP. This approach enabled estimation of GIP changes over time, including periods without data. Boxplots of GIP estimates indicated systematic depletion and decreasing spatial variability, reflecting the impacts of degasification. Comparison with cumulative gas production from empirical well records showed approximately 85% agreement based on a relative similarity metric. Spatio-temporal GIP estimates were also used to estimate methane emissions to longwall ventilation systems and compared with reported emissions from the U.S. EPA Greenhouse Gas Reporting Program, showing similar distributions (≈80%) given data limitations. Overall, this integrated modeling approach provides time-dependent GIP estimates with broader implications for resource assessment applications.

Alabama↗
USGS2024

Field evidence and indicators of rockfall fragmentation and implications for mobility

Rockfall fragmentation can play an important role in hazard studies and the design of protective measures. However, the current lack of modeling tools that incorporate rock fragmentation mechanics is a limitation to enhancing studies and design. This research investigates the fragmentation patterns of rockfalls and analyzes the resulting distribution of fragment sizes within corresponding rockfall deposits. We focus on small rock fragments, which provide insights into the dynamics of the rockfall event and can be used as input for numerical modeling. We analyzed multiple rockfall events from locations worldwide, each exhibiting different degrees of fragmentation. Using image analysis techniques, we mapped all visible blocks, determined their volumes, and measured the distances they travelled from the initial point of impact. A key finding is the identification of three indicators of fragmentation. First, in cases where fragmentation was largely absent, we observed a trend of increasing block size with distance from the impact point or source area, which aligns with previously published findings. However, for energetic rockfall events characterized by intense fragmentation, we observed that small fragments exhibited longer travel distances compared to larger fragments. This distinction allowed us to differentiate blocks primarily resulting from the disaggregation process from those primarily resulting from dynamic fragmentation, with implications for rockfall mobility. Second, although the size distribution of rockfall deposits exhibits a power-law scaling for volumes larger than a minimum size threshold corresponding to a rollover of the distribution, in some case studies a deviation from power-law scaling is observed, indicating a process of larger block comminution due to fragmentation. Third, we found that rockfalls with fragmentation experience reduced mobility, indicated by higher reach angles, and higher lateral dispersion showing a wider distribution of trajectories. We interpret these findings as being directly related to the energy-consuming nature of fragmentation, which prevents farther deposition of fragmented rock blocks.

Albacete province, Lombardy and Aosta Valley, Yose↗
USGS2026

Hyperspectral narrowband imaging spectroscopy: A new paradigm for Earth observation

This editorial introduces the Special Issue entitled “Hyperspectral Narrowband Imaging Spectroscopy: A New Paradigm for Earth Observation” in the August 2026 issue of Photogrammetric Engineering & Remote Sensing (PE&RS), the flagship journal of the American Society for Photogrammetry and Remote Sensing (ASPRS). This volume represents the fourth dedicated hyperspectral special issue published in PE&RS, following earlier contributions by Thenkabail et al. (2025, 2024a, 2024b), and continues ASPRS’s commitment to advancing cutting‑edge imaging spectroscopy research and its applications across Earth system science. Remote sensing is undergoing one of the most profound transformations in its history. The emergence of hyperspectral narrowband (HNB) imaging spectroscopy data, capable of acquiring hundreds of contiguous, narrow spectral bands, has shifted the discipline from observing Earth in a handful of broad spectral windows to capturing continuous spectral signatures of the Planet. This transition marks a decisive break from the multispectral paradigm that has dominated satellite remote sensing for nearly five decades, driven by the advent of new orbital imaging spectrometers such as EnMAP, PRISMA, and NASA’s EMIT, and by the forthcoming Surface Biology and Geology (SBG) mission ((Pires Silva et al., 2026; Bourriz et al., 2025; Thenkabail et al., 2025; Chabrillat et al., 2024; Aneece et al., 2024; Dave et al., 2024; Thenkabail et al., 2024a; Thenkabail et al., 2024b; Thenkabail, 2024a; Thenkabail, 2024b; Thompson et al., 2022; Kokaly et al., 2022; Aneece & Thenkabail, 2022; Cawse Nicholson et al., 2021; Guanter et al., 2021; Vangi et al., 2021; Thenkabail et al., 2021). These missions (e.g., Table 1) deliver unprecedented spectral fidelity, improved signal to noise ratios, and global coverage capabilities, enabling a new era of quantitative, spectroscopy based Earth observation. Where multispectral broadbands (MBBs) provide only a few discrete measurements along the electromagnetic spectrum, HNB systems deliver rich, diagnostic information that enables scientists to characterize Earth’s surface with unprecedented biochemical, biophysical, and structural detail (Figure 1a, 1b). The implications for environmental monitoring, agriculture, water resources, and mineral exploration are profound. Several overarching themes emerge: • Spectral fidelity matters. The ability to preserve subtle absorption features is essential for mineral mapping, vegetation trait retrieval, and biochemical modeling. • AI and deep learning are indispensable. From destriping to classification, modern analytics must be scalable, label‑efficient, and capable of exploiting the full spectral–spatial richness of HNB data. • Physics‑based and data‑driven approaches must converge. Radiative transfer models such as PROSAIL, enhanced with localized soil parameterizations, remain foundational for biophysical retrievals and model‑based inference. • Dimensionality reduction and feature extraction are critical. Techniques such as L1‑ISOMAP demonstrate that intelligent manifold learning can unlock the structure of fused, high‑dimensional datasets. • Next‑generation architectures must be interactive and multimodal. ICTNet exemplifies the future of hyperspectral classification: hybrid, synergistic, and capable of modeling both local textures and global spectral dependencies.

Photogrammetric Engineering and Remote Sensing (PE↗
USGS2025

Refining the earthquake history of south-central Alaska through lake records

The Alaska–Aleutian subduction zone (AASZ) is one of the world's most seismically active plate boundaries and the source of the 1964 M w 9.2 Great Alaska earthquake–the second largest instrumentally recorded earthquake in the world. Understanding the nature and frequency of such earthquakes is necessary for seismic and tsunami hazard assessment, but instrumental and historical records that span less than 150 years are too short to allow a statistically reliable analysis of earthquake recurrence times. This calls for studies of evidence of past earthquakes, extending the earthquake catalog further back in time. Subduction-zone paleoseismology in south-central Alaska is predominantly based on coastal evidence of land-level changes and tsunamis generated by megathrust earthquakes and preserved in the geological record. A complementary approach is lacustrine paleoseismology, which is still a relatively young discipline in Alaska. However, globally, lake basins are well-established high-resolution and continuous recorders of paleoseismic activity along subduction zones, relying on the identification of underwater landslide deposits and turbidites generated by seismic shaking. As a result, lake basins not only register ground shaking from megathrust earthquakes, but also from intraslab and crustal earthquakes, which are typically not accompanied by significant land-level changes. In this review paper, we combine coastal and lacustrine paleoseismology approaches to refine the south-central Alaskan earthquake history by comparing the paleoseismic records from two lakes (i.e., Eklutna Lake, located in the Chugach Mountain Range, and Skilak Lake, situated on the Kenai Peninsula) with the coastal and crustal earthquake catalog in Alaska. The resulting age ranges of all known megathrust earthquakes involving the Alaskan megathrust between the Kodiak and Prince William Sound (PWS) sections are more precise and accurate for the last 1.3 kyrs BP than the previously published age ranges from coastal records. As a result, this study supports the following key conclusions: (1) The 1964 CE earthquake was an exceptionally strong and unique event in the last 2000 years, rupturing the PWS, Kenai, Barren Islands, and Kodiak sections simultaneously. (2) The high-resolution and seasonal markings of the varved lake records now disentangle for the first time closely timed earthquakes, which was not possible based on the coastal evidence alone. (3) No persistent megathrust rupture boundaries exist. So, the possibility of a full rupture of the entire eastern AASZ, from PWS to Semidi cannot be excluded. (4) The rupture pattern in the eastern AASZ reveals superimposed cycles of multi-asperity ruptures (1964 earthquake) and clustered complementary partial ruptures, or rupture cascades. (5) The PWS section hosts the largest asperity in the eastern AASZ. (6) The shaking record of megathrust earthquakes indicates a time-dependent (quasiperiodic) behavior for the study area, but the observation of complementary clusters means that the hazards will not drop to zero but instead may even increase for a neighboring section. (7) The time-independent behavior of intraplate earthquakes implies that the intraslab hazard did not decrease following the 2016 and 2018 earthquakes. This study utilizes an integrated approach for subduction zone paleoseismology as a solution for unraveling recurrence and rupture patterns in Alaska, which can be applied worldwide.

Alaska↗
USGS2026

Inference of pattern-based geological CO2 sequestration and oil recovery potential in a commingled main pay and residual oil zone CO2-EOR flood

Several detailed studies have shown that residual oil zones (ROZs) can present significant resources for additional hydrocarbon recovery as well as subsurface carbon dioxide (CO 2 ) sequestration via enhanced oil recovery by injecting CO 2 (CO 2 -EOR). Field development strategies included new wells drilled dedicated to main pay zones (MPZ) and ROZs, or existing wells in MPZs deepened to ROZs for commingled injection-production using different well patterns. The latter presented a challenge when discerning the injection and production from each of the zones, and for subsequent quantification of CO 2 sequestration and EOR potential from different patterns and from the field. In this paper, an innovative method for analyzing commingled injections and productions from MPZs and ROZs, with application to pattern-based data from four staggered line drive patterns in Wasson Field's Denver Unit, Texas, USA, was developed. Decline curve and ratio-trend methods were used as means of history-matching and forecasting. Cumulative production-time and cumulative production-rate data for oil, gas, and water, as well as water-oil ratio (WOR) and gas-oil ratio (GOR), were analyzed along with injection data for time intervals covering major injection events in MPZ, or MPZ and ROZ combined. A combined analysis enabled inference of allocation of fluids into different zones during WAG (water alternating gas) injection and thereby estimation of CO 2 storage, utilization, and retention in different zones as a function of total injection. Results show that ROZs generally present higher CO 2 sequestration potential compared to MPZs, and a comparable incremental oil recovery factor of ∼20%, on average. Results based on ratio analysis further show that while the WOR trend of the pattern production is mostly dominated and controlled by ROZ, GOR is controlled by both intervals. Although the method relying on decline curves and the approach used in zonal fluid allocations are subject to their limitations, this study presents a practical and innovative well-pattern-based method to infer and forecast CO 2 sequestration and oil recovery quantities and fluid ratios from MPZs and ROZs in commingled operations and highlight the added potential offered by ROZs.

Texas↗
USGS2025

Preface to the focus section on earthquake-induced ground deformation

Ground failure due to earthquake-induced liquefaction, surface fault rupture, and landsliding has caused substantial damage in the past and continues to pose risks to critical infrastructure in the future. The consideration of ground failure is central to engineering analysis and design, ranging from site-specific engineering assessments of ground failure potential to broader regional-scale ground failure assessments of near-real-time earthquake impacts or longer-term portfolio risk. Uncertainties in all aspects of the problem complicate the prediction of earthquake-induced ground failure, including the identification of hazard-susceptible geomaterials, characterizing their spatial extent and physical properties, spatio-temporal variability in groundwater conditions, characterization of earthquake ground motions, assessing ground failure severity, and linking ground failure severity to infrastructure damage and loss.

Seismological Research Letters↗
USGS2025

Increased flood exposure in the Pacific Northwest following earthquake-driven subsidence and sea-level rise

Climate-driven sea-level rise is increasing the frequency of coastal flooding worldwide, exacerbated locally by factors like land subsidence from groundwater and resource extraction. However, a process rarely considered in future sea-level rise scenarios is sudden (over minutes) land subsidence associated with great (>M8) earthquakes, which can exceed 1 m. Along the Washington, Oregon, and northern California coasts, the next great Cascadia subduction zone earthquake could cause up to 2 m of sudden coastal subsidence, dramatically raising sea level, expanding floodplains, and increasing the flood risk to local communities. Here, we quantify the potential expansion of the 1% floodplain (i.e., the area with an annual flood risk of 1%) under low (~0.5 m), medium (~1 m), and high (~2 m) earthquake-driven subsidence scenarios at 24 Cascadia estuaries. If a great earthquake occurred today, floodplains could expand by 90 km 2 (low), 160 km 2 (medium), or 300 km 2 (high subsidence), more than doubling the flooding exposure of residents, structures, and roads under the high subsidence scenario. By 2100, when climate-driven sea-level rise will compound the hazard, a great earthquake could expand floodplains by 170 km 2 (low), 240 km 2 (medium), or 370 km 2 (high subsidence), more than tripling the flooding exposure of residents, structures, and roads under the high subsidence scenario compared to the 2023 floodplain. Our findings can support decision-makers and coastal communities along the Cascadia subduction zone as they prepare for compound hazards from the earthquake cycle and climate-driven sea-level rise and provide critical insights for tectonically active coastlines globally.

California, Oregon, Washington↗
USGS2025

Site response and wave propagation effects in the eastern United States

Fourier amplitude spectra from regional earthquakes in the eastern United States are used in a parametric inversion for source, path, and site effects. Five earthquakes are selected for analysis during the installation of the United States National Seismic Network (US), Earthscope’s USArray Transportable Array (TA), and other temporary arrays to maximize station coverage. A global search algorithm is used to solve for site response from 0.1 to 15 Hz, corner frequency, geometrical spreading ( r - γ ), and frequency dependent anelastic attenuation in the form Q(f) = Q o f α . Tradeoff between moment and geometric spreading is handled by fixing the moment. The tradeoff between corner frequency and Q(f) is solved by selecting the value of corner frequency that minimizes an objective function defined over all stations. Values of site response and attenuation parameters show a strong spatial correlation with the physiographic provinces of the eastern United States. Site response for the Atlantic Coastal Plain is consistent with previous work using spectral ratios relative to a reference site, defined by strong resonance peaks correlated with the thickness of sediments. Site response for the other physiographic provinces is markedly different from the coastal plain, with a lack of distinct resonance peaks and a broad moderate high at frequences from 0.1 to 0.5 Hz consistent with the hard-rock geology of the regions. Like site response, Q(f) has a strong correlation with physiographic province, showing lower values on the coastal plain and higher values inland. Geometric spreading exponent, γ, decreases with increasing hypocenter distance from just above 1 at a few tens of kilometers to 0.9 at 500 km. The limited range in geometric spreading values is attributed to starting the Fourier transform window at the S ‐wave arrival for all distances and averaging over multiple wave types.

eastern United States↗
USGS2025

Modeling seawater intrusion along the Alabama coastline using physical and machine learning models to evaluate the effects of multiscale natural and anthropogenic stresses

Seawater intrusion threatens groundwater resources in coastal regions, including southern Baldwin County, Alabama, where the freshwater-saltwater interface dynamics remain poorly understood. To address this gap, this study uses combined physics-based and machine-learning models to quantify seawater intrusion caused by natural (storm surges) and anthropogenic (human activities) perturbations. The long short-term memory network and wavelet analysis were used to assess vertical aquifer vulnerabilities, revealing that the shallow part of the Coastal lowlands aquifer system (CL1) in the southern Baldwin County region is more susceptible to sea level rise and groundwater extraction than deeper aquifers. Based on these findings, a cross-sectional numerical model (physics approach) for the CL1 aquifer was developed to evaluate tidal and storm surge effects, using Tropical Storm Claudette (June 2021) as a case study. Results showed that tidal fluctuations had a minimal impact on the saltwater-freshwater interface location, whereas storm surges caused substantial inland movement, with effects lasting for nine months. The steady-state version of the three-dimensional (3D) physical model predicted seawater intrusion across the entire area, and convolutional neural network-based modeling further validated the model results. The 3D physical model was also applied to a smaller area to assess human impact on the saltwater interface due to two groundwater pumping scenarios (± 50% of the baseline pumping rate). Results revealed that a 50% increase in groundwater withdrawals caused seawater to advance ~ 320 m inland, whereas a 50% reduction led to a ~ 270-meter retreat. This study highlights the vulnerability of Alabama’s shallow coastal aquifers to seawater intrusion due to storm surges and human activities, and demonstrates that combining physics-based models with machine learning approaches can improve groundwater predictions, though its accuracy depends on the availability of site-specific data.

Alabama↗