Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Contribution”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56Linked to original sources

Spatially telescoping measurements for improved characterization of groundwater-surface water interactions

The suite of measurement methods available to characterize fluxes between groundwater and surface water is rapidly growing. However, there are few studies that examine approaches to design of field investigations that include multiple methods. We propose that performing field measurements in a spatially telescoping sequence improves measurement flexibility and accounts for nested heterogeneities while still allowing for parsimonious experimental design. We applied this spatially telescoping approach in a study of ground water-surface water (GW-SW) interaction during baseflow conditions along Lucile Creek, located near Wasilla, Alaska. Catchment-scale data, including channel geomorphic indices and hydrogeologic transects, were used to screen areas of potentially significant GW-SW exchange. Specifically, these data indicated increasing groundwater contribution from a deeper regional aquifer along the middle to lower reaches of the stream. This initial assessment was tested using reach-scale estimates of groundwater contribution during baseflow conditions, including differential discharge measurements and the use of chemical tracers analyzed in a three-component mixing model. The reach-scale measurements indicated a large increase in discharge along the middle reaches of the stream accompanied by a shift in chemical composition towards a regional groundwater end member. Finally, point measurements of vertical water fluxes -- obtained using seepage meters as well as temperature-based methods -- were used to evaluate spatial and temporal variability of GW-SW exchange within representative reaches. The spatial variability of upward fluxes, estimated using streambed temperature mapping at the sub-reach scale, was observed to vary in relation to both streambed composition and the magnitude of groundwater contribution from differential discharge measurements. The spatially telescoping approach improved the efficiency of this field investigation. Beginning our assessment with catchment-scale data allowed us to identify locations of GW-SW exchange, plan measurements at representative field sites and improve our interpretation of reach-scale and point-scale measurements.

Alaska↗

Pavement alters delivery of sediment and fallout radionuclides to urbanstreams

Sediment from urban impervious surfaces has the potential to be an important vector for contaminants, particularly where stormwater culverts and other buried channels draining large impervious areas exit from underground pipes into open channels. To better understand urban sediment sources and their relation to fallout radionuclides, we collected samples of rainfall, urban sediment (pavement sediment, topsoil), streambank sediment, and fluvial sediment (suspended sediment and bed sediment) for 7 Be, 210 Pb ex , and 137 Cs analysis. The results indicate that each rainfall event tags pavement sediment with elevated activities of 7 Be and 210 Pb ex such that runoff from impervious surfaces in the buried channel part of the stream network contains the highest activities. Pavement sediment, because it is characteristically a thin veneer, has a small mass to rainwater ratio resulting in a greater tagging of 7 Be and 210 Pb ex activity than does topsoil on a per gram basis. An unmixing model indicated that suspended-sediment samples collected at the culvert outlet from the buried-channel network are from pavement sediment sources (45 ± 25%) with a smaller component of topsoil (22 ± 19%), and a component from streambanks (32 ± 35%) that we infer to be older channel material and subsoil eroded from within the culvert system. Downstream from the culvert, suspended sediment collected from the open-channel parts of the stream had 7 Be and 210 Pb ex activities that were substantially reduced by the contribution of sediment from streambanks (57 ± 15%), with pavement contributions decreasing to 15 (±9%) and topsoil contributing 28 (±7%). The results highlight the utility of 7 Be, 210 Pb ex , and 137 Cs as tracers of urban sediment sources, resulting in a unique radionuclide signature for urban watersheds compared to other sediment-source settings.

Maryland↗

Temporal and spatial variations in river specific conductivity: Implications for understanding sources of river water and hydrograph separations

Specific conductivity (SC) is commonly used to estimate the proportion of baseflow (i.e., waters from within catchments such as groundwater, interflow, or bank return flows) contributing to rivers. Reach-scale SC comparisons are also useful for identifying where multiple water stores contribute to baseflow. Daily SC values of adjacent gauges in Australian (the Barwon, Glenelg, and Campaspe Rivers) and North American (the Upper Colorado River) catchments are commonly not well correlated (R 2 = 0.32 to 0.82). Smoothed inter-gauge SC values averaged over 7 to 45 days are better correlated and define a series of hysteresis loops. The variable SC patterns between adjacent gauges probably reflect varying proportions of groundwater, bank return waters, interflow, and soil water contributing to baseflow. In some rivers using SC values to compare baseflow along river reaches on sub-annual timescales may be not be feasible.

Journal of Hydrology↗

The influence of land cover and storm magnitude on hydrologic flowpath activation and runoff generation in steep tropical catchments of central Panama

Despite abundant research documenting that land use/land cover (LULC) have substantial impacts on the hydrology of humid tropical systems, field-based evidence for the physical mechanisms behind these impacts are still lacking. In particular, our understanding of the hydrologic flowpaths that generate runoff in these systems, and how they vary with respect to LULC is insufficient to inform both physically-based hydrologic modeling and land-use decision-making. In this study, we use end-member mixing analysis (EMMA) of stream chemistry, and hydrometric characterizations of hillslope soil moisture to identify hydrologic flowpaths in humid tropical steep-land catchments of varying LULC: mature tropical forest, young secondary tropical forest, cattle pasture. EMMA was applied to data from 14 storm events (six at the mature forest, five at the young secondary forest, and three at the cattle pasture) that were intensively sampled during the 2017 wet season representing a wide range of rainfall magnitudes and intensities. Additionally, volumetric-soil-moisture responses at multiple depths were characterized during and after 74 storm events occurring from 2015 to 2017. EMMA results indicated that lateral preferential flow within the top 30 cm of the soil profile was a dominant source of runoff generation at the two forested catchments, with the contribution of this flow path increasing with rainfall magnitude and intensity. This was corroborated by volumetric-soil-moisture data, that showed that a perched zone of saturation developed at 30 cm at the time of peak storm runoff during the largest events and lasted for the remaining duration of the event. EMMA indicated that runoff was a combination of infiltration-excess overland flow and lateral subsurface flow in the actively grazed pastoral catchment. There, overland flow contributed 62 % of runoff during the highest runoff rate sampled (35.3 mm/hr) and this contribution increased substantially with storm magnitude. This flowpath identification was also supported by volumetric-soil-moisture data at the pasture, with peak saturation at all depths during the largest storm events occurring up to 30 min after peak runoff. These results provide a mechanistic explanation for previously observed hydrologic differences among tropical LULCs. Additionally, the wide range of hydrologic conditions during these storm events provide a basis for understanding how future changes to this, and similar humid tropical regions will impact hydrological processes and water availability.

Journal of Hydrology↗

The geochemistry of loess: Asian and North American deposits compared

Loess is widely distributed over Asia and North America and constitutes one of the most important surficial deposits that serve as terrestrial records of the Quaternary. The oldest Pleistocene loess in China is likely ∼2.6 Ma, thus spanning much or all of the Pleistocene. In North America, most loess is no older than the penultimate glacial period, with the exception of Alaska, where the record may go back to ∼3.0 Ma. On both continents, loess deposits date primarily to glacial periods, and interglacial or interstadial periods are represented by paleosols. Both glacial and non-glacial sources of silts that comprise the bulk of loess deposits are found on both continents. Although loess has been considered to be representative of the average upper continental crust, there are regionally distinctive compositions of loess in both Asia and North America. Loess deposits in Asia from Yakutia, Tajikistan, and China have compositionally distinct major element compositions, due to varying abundances of silicate minerals, carbonate minerals, and clay minerals. In North America, loess in the Mississippi River valley, the Great Plains, and Alaska are also distinguishable with regard to major element composition that reflects highly diverse source sediments. Trace element geochemistry (Sc-Th-Zr and the rare earth elements) also shows regional diversity of loess bodies, in both Asia and North America. On both continents, most loess bodies show significant contributions from later-cycle, altered sedimentary rocks, as opposed to direct derivation from igneous rocks. Further, some loess bodies have detectable contributions from mafic igneous rocks as well as major contributions from average, upper-crustal, felsic rocks. Intercalated paleosols in loess sections show geochemical compositions that differ significantly from the underlying loess parent materials. Ratios of soluble-to-insoluble elements show depletions in paleosols due to chemical weathering losses of calcite, dolomite, plagioclase, mica, apatite, and smectite. In Asia and North America, the last interglacial paleosol is more weathered than equivalent modern soils, which could be due either to a climate that was warmer and more humid, a longer period of pedogenesis, or both. In Asia, early Pleistocene loess and paleosols are both more weathered than those from the middle and late Pleistocene, forming prior to a mid-Pleistocene aridification of Asia from uplift of the Tibetan Plateau. Understanding the geochemistry of loess and paleosols can tell us much about past atmospheric circulation, past temperature and moisture regimes, and even tectonic processes.

Journal of Asian Earth Sciences↗

Changes in sediment source areas to the Amerasia Basin, Arctic Ocean, over the past 5.5 million years based on radiogenic isotopes (Sr, Nd, Pb) of detritus from ferromanganese crusts

Ferromanganese (FeMn) crusts provide a useful paleoenvironmental archive for studying the poorly understood climatic, oceanographic, and geologic evolution of the Arctic Ocean. This study is based on the identification and temporal reconstruction of sources and inferred transport pathways of terrigenous material in FeMn crusts collected from several sites across the Amerasia Basin. Samples from the Alpha Ridge (AR), Mendeleev Ridge (MR), and Chukchi Borderland (CB) have similar chemical compositions and high detrital contents. Sr, Nd, and Pb isotopic compositions of the terrigenous detritus extracted from the FeMn crust layers show spatial and temporal variability due to the variable proportions of inputs from the North American and East Siberian margins and local submarine outcrops. The temporal resolution is restricted by macroscopic crust layers, which represent times of significant changes in the depositional environment and are used to study first-order environmental changes. During the period of ca. 4.4 to 3.8 Myr ago, detritus in the MR area was derived mostly from the Laptev Sea. Then, until about 1.3 Myr ago, FeMn crusts from MR received a higher volcanic component sourced from the East Siberian Sea, with mixing of detritus from the Okhotsk-Chukotka volcanic belt (OCVB) area and possibly weathering of local MR outcrops, which is mostly High Arctic Large Igneous Province (HALIP) rocks. The period from about 1.3 Myr ago to the present reflects enhanced contributions of detritus from the Canadian Shield, approximately equal to the East Siberian contribution for the MR area. CB crusts show three main periods of distinct detrital input. During the period ca. 5.5–5.0 Myr ago, CB detritus was sourced from local submarine outcrops of the Jurassic-Cretaceous HALIP rocks and possibly from northeast Siberia, including OCVB rocks, while during the period from about 5.0 to 3.6 Myr ago, the CB FeMn crusts had a much greater input of detritus from the North American margin. After 3.6 Myr ago, the CB detritus shows a mixed composition predominantly sourced from North America with some material transported from the Bering Sea and smaller contributions from northeast Siberia. The AR crust was influenced mostly by detritus sourced from the Canadian Shield. This study shows that FeMn crusts from the Arctic ocean are a useful tool and archive for climate reconstruction and depositional history of this polar region.

Marine Geology↗

Discerning sediment provenance in the Outer Banks (USA) through detrital zircon geochronology

Detrital zircon data from modern barrier island and estuarine environments in the Outer Banks (Atlantic Coast, USA) were statistically compared to sands from nearby rivers to assist in determining source-to-sink pathways. Fluvial samples, collected from near the Fall Line contact between the Appalachian Orogen and sediments of the coastal plain, all have age unique distributions, making them ideal for tracing provenance. Three samples from the Atlantic foreshore showed high similarities to one another, as well as to three samples from the estuarine (back-barrier) Pamlico and Albemarle Sounds. Mixture modeling with multiple data reduction methods and three different statistical tests for similarity consistently indicated that the nearby Potomac River was the primary source for all Atlantic foreshore and estuarine zircons, followed by minor contributions from the James River in some models. The models indicate little or no sediment contribution from the Susquehanna, Roanoke, Tar, Neuse, Cape Fear, and Peedee Rivers. Both Atlantic foreshore and estuarine sands are therefore interpreted to have initially originated from Appalachian bedrock to the north of their present-day location, and subsequently to have been transported southward through the Chesapeake Bay watershed before deposition in Virginia and North Carolina. Prior to barrier island formation in the last several thousand years, differing geomorphology of the Chesapeake Bay facilitated southward movement of sediments from its constituent rivers via longshore drift, where they were deposited in coastal settings on the mainland. The modern barrier islands, formed during the most recent post-glacial transgression, may be reworked from these deposits, but may also include a contribution from sediments that were derived more recently from relict deposits on the shelf. Oceanographic and sedimentological evidence suggests that movement of sand-sized grains from southern rivers across the back-barrier sounds is unlikely. These findings can assist with coastal resilience planning and resource management in a region under severe threat from climate change and rising sea levels.

North Carolina, Virgina↗

Gaia's breath - Global methane exhalations

Methane (CH4) is the most abundant organic compound in the Earth's atmosphere, where it acts as a greenhouse gas and thus has implications for global climate change. The current atmospheric CH4 budget, however, does not take into account geologically-sourced CH4 seepage. Geological sources of CH4 include natural macro- and micro-seeps, mud volcanoes, and other miscellaneous sources such as gas hydrates, magmatic volcanoes, geothermal regions, and mid-ocean ridges. Macro-seeps contribute ???25 Tg (teragrams) CH4/yr to the atmosphere, whereas, micro-seepage contributes perhaps 7 Tg CH4/yr. Mud volcanoes emit ???5 Tg CH4/yr, and miscellaneous sources emit ???8 Tg CH4/yr to the atmosphere. Thus, the total contribution to the atmosphere from geological sources is estimated to be 45 Tg CH4/yr, which is significant to the atmospheric organic carbon cycle and should be included in any global inventory of atmospheric CH4. We argue that the atmospheric CH4 global inventory of the Interplanetary Panel on Climate Change must be adjusted in order to incorporate geologically-sourced CH4 from naturally occurring seepage.

Marine and Petroleum Geology↗

Temperature and precipitation source variability and glacial dynamics in the southwestern United States at Fish Lake, Utah, since late MIS 4

An improved understanding of hydroclimate response to natural climate forcings is needed to evaluate impacts of changing seasonal circulation patterns on current and future drought in the southwestern United States (‘the Southwest’). However, few terrestrial records from the Southwest preserve changes in moisture availability continuously prior to the Last Glacial Maximum (LGM, ∼24.5 ka). Fish Lake, in the Upper Colorado River Basin, preserves a long (∼67 ka), continuous, high-resolution (∼3.3 cm/century) sedimentary record spanning from late Marine Isotope Stage (MIS) 4 to present. Here, we investigate the relative contributions of seasonal precipitation and moisture source using the hydrogen isotope value of the n -C 29 leaf wax alkane and changes in temperature using branched glycerol dialkyl glycerol tetraethers (brGDGTs). During the warm post glacial period (14 ka to present), a greater contribution of annual precipitation is sourced from the North American Monsoon (NAM) in response to declining winter insolation and rising greenhouse gases, weakening westerly storms and shifting them northward. MIS 3 (∼61 to 29 ka) is also influenced by NAM inputs, however, to a smaller magnitude than during the post glacial period when temperatures were warmer. However, stadial periods (MIS 2, 29 to 14.1 ka) show 2 H-enriched values, suggesting warm conditions and large contributions of NAM precipitation during the LGM, contradicting other proxies and regional records. The LGM is the only period in the record where glaciers are present in the catchment, thus we hypothesize glacial erosion reworked pre-LGM aged soil organic matter and biased the record during this time.

Utah↗

Hyperspectral remote sensing of white mica: A review of imaging and point-based spectrometer studies for mineral resources, with spectrometer design considerations

Over the past ~30 years, hyperspectral remote sensing of chemical variations in white mica have proven to be useful for ore deposit studies in a range of deposit types. To better understand mineral deposits and to guide spectrometer design, this contribution reviews relevant papers from the fields of remote sensing, spectroscopy, and geology that have utilized spectral changes caused by chemical variation in white micas. This contribution reviews spectral studies conducted at the following types of mineral deposits: base metal sulfide, epithermal, porphyry, sedimentary rock hosted gold deposits, orogenic gold, iron oxide copper gold, and unconformity-related uranium. The structure, chemical composition, and spectral features of white micas, in this contribution defined as muscovite, paragonite, celadonite, phengite, illite, and sericite, are given. Reviewed laboratory spectral studies determined that shifts in the position of the white mica 2200 nm combination feature of 1 nm correspond to a change in Al oct content of approximately ±1.05%. Many of the reviewed spectral studies indicated that a shift in the position of the white mica 2200 nm combination feature of 1 nm was geologically significant. A sensitivity analysis of spectrometer characteristics; bandpass, sampling interval, and channel position, is conducted using spectra of 19 white micas with deep absorption features to determine minimum characteristics required to accurately measure a shift in the position of the white mica 2200 nm combination feature. It was determined that a sampling interval < 16.3 nm and bandpass <17.5 nm are needed to achieve a root mean square error (RMSE) of 2 nm, whereas a sampling interval < 8.8 nm and bandpass <9.8 nm are needed to achieve a RMSE of 1 nm. For comparison, commonly used imaging spectrometers HyMap, AVIRIS-Classic, SpecTIR®'s AisaFENIX 1K, and HySpex tm SWIR 384 have 2.1, 1.2, 0.96, and 0.95 nm RMSE in determining the position of the 2200 nm white mica combination feature, respectively. An additional sensitivity analysis is conducted to determine the effect of signal to noise ratio (SNR) on the RMSE of the position of the white mica 2200 nm combination feature, using spectra of 18 white micas with deep absorption features. For a spectrometer with sampling interval and bandpass of 1 nm, we estimate that RMSEs of 1 and 1.5 nm are achievable with spectra having a minimum SNR of approximately 246 and 64, respectively. For a spectrometer with sampling interval and bandpass of 5 nm, we estimate that RMSEs of 1 and 1.5 nm are attainable with spectra having a minimum SNR of approximately 431 and 84, respectively. When using a spectrometer with a sampling interval 8.8 nm and a bandpass of 9.8 nm, a RMSE of 1 is only achievable with convolved, noiseless reference spectra. For the 8.8_9.8 nm spectrometer, spectra with SNR of 250 and 100 result in RMSE of 1.1 and 1.3, respectively. Therefore, fine spectral resolution characteristics achieve RMSEs better than 1 nm for high SNR spectra while spectrometers with coarse spectral resolution have larger RMSE, perform well with noisy data, and are useful for white mica studies if RMSE of 1.1 to 1.5 nm is acceptable.

Remote Sensing of Environment↗

Methane and nitrous oxide temporal and spatial variability in two midwestern USA streams containing high nitrate concentrations

Concentrations and emissions of greenhouse gases CO 2 , CH 4 , and N 2 O commonly are examined individually in aquatic environments in which each is expected to be relatively important; however, their co-occurrence and dynamic interactions in fluvial settings could provide important information about their controlling biogeochemical processes and potential contributions to global climate change. Spatial and temporal variability of CH 4 , N 2 O, and CO 2 concentrations were measured from June 1999 to September 2003 in two nitrate-rich (40–1200 μM) streams draining agricultural land in the midwestern USA that differed ~13-fold in flow. Seasonal (biweekly), diel (hourly), and transport-oriented (reach-scale) sampling approaches were compared. Dissolved gas concentrations exceeded atmospheric equilibrium values up to 700- and 16-fold, for CH 4 and N 2 O, respectively. Mean concentrations were higher in the larger stream than in the smaller stream. In both streams, CH 4 emissions were generally higher in summer-fall and negatively correlated with flow and NO 3 − concentration while N 2 O emissions were generally higher in winter/spring and positively correlated with flow and NO 3 − . In the small stream, diel variations in the concentrations, emissions, and isotopic compositions of CH 4 , N 2 O, and NO 2 − resulted from diel variations in sources, sinks, and air-water gas exchange velocities. Seasonal mean total (CH 4 + N 2 O) area-normalized emission rates, expressed as CO 2 warming potential equivalents, were similar for the two streams, but the total reach-scale emission rate for the larger stream, including CO 2 , was about 2.9 times that of the smaller stream (131.6 vs 46.0 kg CO 2 equivalents km −1 day −1 , respectively). The CH 4 contribution to this flux was 9–28%, despite the relatively high NO 3 − and O 2 concentrations in the streams, indicating contributions from upwelling groundwater or reactions in streambed sediment.

Illinois, Indiana↗

Pesticide mixtures show potential toxicity to aquatic life in U.S. streams, water years 2013-2017

During water years (WY) 2013–2017, the U.S. Geological Survey, National Water-Quality Assessment (NAWQA) Project, sampled the National Water Quality Network – Rivers and Streams (NWQN) year-round and reported on 221 pesticides at 72 sites across the United States in agricultural, developed, and mixed land use watersheds. The Pesticide Toxicity Index (PTI) was used to estimate the potential chronic and acute toxicity to three taxonomic groups – fish, cladocerans, and benthic invertebrates. For invertebrates (either cladocerans, benthic invertebrates, or both), the maximum PTI score exceeded the predicted acute toxicity screening level at 18 of the 72 sites (25%) at some point during WY 2013–2017. The predicted toxicity of a single pesticide compound was found to overwhelm the toxicity of other pesticides in the mixtures after concentrations were toxicity weighted. For this study, about 71%, 72%, and 92% of the Fish-, Cladoceran-, and Benthic Invertebrate-PTI scores, respectively, had one pesticide compound primarily contributing to sample potential toxicity (>50%). There were 17 (13 insecticides, 2 herbicides, 1 fungicide, and 1 synergist) of the 221 pesticide compounds analyzed that were the primary drivers of potential toxicity in each water sample in which the PTI and TUmax (toxic unit score for the pesticide that makes the single largest contribution to the PTI) scores were above predicted chronic (>0.1) or acute (>1) toxicity levels for one of the three taxa. For cladocerans and benthic invertebrates, the drivers of predicted chronic (>0.1) and acute (>1) PTIs were mostly insecticides. For cladocerans, the pesticide compounds driving the PTI scores were bifenthrin, carbaryl, chlorpyrifos, diazinon, dichlorvos, dicrotophos, diflubenzuron, flubendiamide, and tebupirimfos. For benthic invertebrates, atrazine (an herbicide), as well as the insecticides – bifenthrin, carbaryl, carbofuran, chlorpyrifos, diazinon, dichlorvos, fipronil, imidacloprid, and methamidophos – were the drivers of predicted toxicity. For fish, there were three pesticide types that contributed the most to predicted chronic (>0.1) PTIs – acetochlor, an herbicide; carbendazim, a fungicide degradate; and piperonylbutoxide, a synergist.

Science of the Total Environment↗

Mechanisms for retention of low molecular weight organic carbon varies with soil depth at a coastal prairie ecosystem

Though primary sources of carbon (C) to soil are plant inputs (e.g., rhizodeposits), the role of microorganisms as mediators of soil organic carbon (SOC) retention is increasingly recognized. Yet, insufficient knowledge of sub-soil processes complicates attempts to describe microbial-driven C cycling at depth as most studies of microbial-mineral-C interactions focus on surface horizons. We leveraged a well-studied paleo-marine terrace (90 ka) located near Santa Cruz, CA, to characterize the short-term (days to weeks) and intermediate-term (months to years) fate of two low molecular weight organic carbon. compounds at three depths in the soil profile (∼25 cm, A horizon; ∼75 cm A/B transition; and ∼125 cm, B horizon). We employed isotopically-labeled glucose (GLU) and oxalic acid (OXA) to represent two common classes of rhizodeposits: carbohydrates and organic acids. Using a combination of laboratory (9 d) and field (490 d) incubations, we traced the fate of GLU-C and OXA-C through dissolved-, metal-associated-, and microbially-respired CO2 and bulk SOC pools. Our results suggest new SOC retention (i.e., defined as 13C label identified in solid or aqueous fractions) over intermediate time frames (490 d) is correlated with patterns in short-term (9 d) cycling dynamics, which in turn is related to the theoretical efficiency by which microorganisms process each substrate. For all horizons (A, A/B, and B) GLU-C was converted to CO2 more quickly than OXA-C with modeled decomposition rates ∼2–4 times faster for GLU depending on microbial density (higher in A than B horizon). The faster decomposition rates of GLU-C increased fractional recovery (0.399 ± 0.026 to 0.504 ± 0.030 for GLU-C) compared to OXA-C (0.035 ± 0.003 to 0.127 ± 0.010) among all horizons in our field experiment (490 d). Though the overall proportion of GLU-C recovered in solid fractions did not vary significantly with horizon, based on 13C recovered in aqueous fractions the apparent mechanism for retention did. After the 9-d laboratory incubation, fractional recovery for GLU-C among C pools associated with microbial biomass was almost 20× higher than OXA-C (0.192 versus 0.010, respectively across all horizons). More than a year later, 43–46% of GLU-C retained in the field incubation was extractable with a neutral salt (representing a pool of soil C residing within or available to microbial biomass) among A and A/B horizons, while only 6% of retained GLU-C was similarly extractable in the B horizon. Thus, it appears among depths with higher microbial density (A, A/B horizons), anabolic recycling is the most likely process contributing to the persistence of glucose C, whereas abiotic sinks contributed more to intermediate-term stability for GLU-C in the B horizon. By contrast, most OXA-C was lost, presumably as CO2, over the short-term from the A and A/B horizons (fractional recovery: 0.136 ± 0.011 and 0.091 ± 0.002, respectively). However, though substantially lower than GLU-C recovered at the conclusion of our field experiment, the fraction of oxalic acid C retained in the B horizon over both short- (0.72 ± 0.037) and intermediate-time (0.127 ± 0.010) frames was several-fold higher than for overlying horizons. The specific process(es) (e.g., more efficient microbial utilization, metal-organic complexation, direct adsorption to the mineral matrix, etc.) contributing to higher retention for OXA-C at depth are discussed but remain unresolved.

Soil Biology and Biochemistry↗

Seasonality of acarological risk of exposure to Borrelia miyamotoi from questing life stages of Ixodes scapularis collected from Wisconsin and Massachusetts, USA

Measures of acarological risk of exposure to Ixodes scapularis -borne disease agents typically focus on nymphs; however, the relapsing fever group spirochete, Borrelia miyamotoi can be transmitted transovarially, and I. scapularis larvae are capable of transmitting B. miyamotoi to their hosts. To quantify the larval contribution to acarological risk, relative to nymphs and adults, we collected questing I. scapularis for 3 yr at Fort McCoy, Wisconsin (WI, n = 23,367 ticks), and Cape Cod, Massachusetts (MA, n = 4,190) in the United States. Borrelia miyamotoi infection prevalence was estimated for I. scapularis larvae, nymphs, females, and males, respectively, as 0.88, 2.05, 0.63, and 1.22% from the WI site and 0.33, 2.32, 2.83, and 2.11% from the MA site. Densities of B. miyamotoi -infected ticks (DIT, per 1,000 m 2 ) were estimated for larvae, nymphs, females, and males, respectively, as 0.36, 0.14, 0.01, and 0.03 from the WI site and 0.05, 0.06, 0.03, and 0.02 from the MA site. Thus, although larval infection prevalence with B. miyamotoi was significantly lower than that of nymphs and similar to that of adults, because of their higher abundance, the larval contribution to the overall DIT was similar to that of nymphs and trended towards a greater contribution than adults. Assuming homogenous contact rates with humans, these results suggest that eco-epidemiological investigations of B. miyamotoi disease in North America should include larvae.A fuller appreciation of the epidemiological implications of these results, therefore, requires an examination of the heterogeneity in contact rates with humans among life stages.

Massachusetts, Wisconsin↗

Distributions of uronic acids and O-methyl sugars in sinking and sedimentary particles in two coastal marine environments

Although recent research has indicated that bacteria may contribute an important fraction of biochemical residues in terrestrial and marine environments, it is difficult for geochemists to identify contributions from these ubiquitous and biochemically diverse organisms. Previous studies have suggested uronic acids and O -methyl sugars may be useful indicators of microbial abundance and activity, but have been limited primarily to analyses of a small number of isolated samples. We report here comparative distributions of O -methyl sugars, uronic acids, and aldoses in sediment trap material and sediments from Dabob Bay, WA and nearby Saanich Inlet, BC, where temporal and spatial trends may be used together with well-established patterns in other biochemicals to identify bacterial contributions against the background of other carbohydrate sources. O -methyl sugars and uronic acids were important contributors to the overall flux and burial of polysaccharide material in Dabob Bay and Saanich Inlet, composing ≤12 wt% of the total carbohydrate yields from sediment trap and sediment samples. O -methyl sugars accounted for an average of 5% of the carbohydrate yields from sediment trap materials and sediments, but were found rarely and only in low abundance in vascular plant tissues, phytoplankton, and kelp. In contrast, uronic acids were abundant products of sediment trap material and sediments, as well as vascular plant tissues, where in some cases they predominated among all carbohydrates. Uronic acid abundance in sediment trap material averaged 3% and ranged to >6% of total carbohydrate yields. The persistence of total minor sugar yields in water column collections from Dabob Bay throughout the seasonal cycle indicated they had a primary source that was not directly related to plankton bloom cycles nor pulsed inputs of vascular plant remains. Subsurface maxima in total minor sugar yields (and several individual components) within sediment cores from both sites indicate in situ sedimentary sources. Taken together, the observed environmental distributions strongly suggest that the minor sugar abundances in Dabob Bay and Saanich Inlet were controlled by in situ microbial production.

British Columbia, Washington↗

Spatial and temporal variability of trace element concentrations in an urban subtropical watershed, Honolulu, Hawaii

Trace metal concentrations in soils and in stream and estuarine sediments from a subtropical urban watershed in Hawaii are presented. The results are placed in the context of historical studies of environmental quality (water, soils, and sediment) in Hawaii to elucidate sources of trace elements and the processes responsible for their distribution. This work builds on earlier studies on sediments of Ala Wai Canal of urban Honolulu by examining spatial and temporal variations in the trace elements throughout the watershed. Natural processes and anthropogenic activity in urban Honolulu contribute to spatial and temporal variations of trace element concentrations throughout the watershed. Enrichment of trace elements in watershed soils result, in some cases, from contributions attributed to the weathering of volcanic rocks, as well as to a more variable anthropogenic input that reflects changes in land use in Honolulu. Varying concentrations of As, Cd, Cu, Pb and Zn in sediments reflect about 60 a of anthropogenic activity in Honolulu. Land use has a strong impact on the spatial distribution and abundance of selected trace elements in soils and stream sediments. As noted in continental US settings, the phasing out of Pb-alkyl fuel additives has decreased Pb inputs to recently deposited estuarine sediments. Yet, a substantial historical anthropogenic Pb inventory remains in soils of the watershed and erosion of surface soils continues to contribute to its enrichment in estuarine sediments. Concentrations of other elements (e.g., Cu, Zn, Cd), however, have not decreased with time, suggesting continued active inputs. Concentrations of Ba, Co, Cr, Ni, V and U, although elevated in some cases, typically reflect greater proportions attributed to natural sources rather than anthropogenic input. ?? 2002 Elsevier Science Ltd. All rights reserved.

Applied Geochemistry↗

Contaminant exposure and transport from three potential reuse waters within a single watershed

Global demand for safe and sustainable water supplies necessitates a better understanding of contaminant exposures in potential reuse waters. In this study, we compared exposures and load contributions to surface water from the discharge of three reuse waters (wastewater effluent, urban stormwater, and agricultural runoff). Results document substantial and varying organic-chemical contribution to surface water from effluent discharges (e.g., disinfection byproducts [DBP], prescription pharmaceuticals, industrial/household chemicals), urban stormwater (e.g., polycyclic aromatic hydrocarbons, pesticides, nonprescription pharmaceuticals), and agricultural runoff (e.g., pesticides). Excluding DBPs, episodic storm-event organic concentrations and loads from urban stormwater were comparable to and often exceeded those of daily wastewater-effluent discharges. We also assessed if wastewater-effluent irrigation to corn resulted in measurable effects on organic-chemical concentrations in rain-induced agricultural runoff and harvested feedstock. Overall, the target-organic load of 491 g from wastewater-effluent irrigation to the study corn field during the 2019 growing season did not produce substantial dissolved organic-contaminant contributions in subsequent rain-induced runoff events. Out of the 140 detected organics in source wastewater-effluent irrigation, only imidacloprid and estrone had concentrations that resulted in observable differences between rain-induced agricultural runoff from the effluent-irrigated and nonirrigated corn fields. Analyses of pharmaceuticals and per-/polyfluoroalkyl substances in at-harvest corn-plant samples detected two prescription antibiotics, norfloxacin and ciprofloxacin, at concentrations of 36 and 70 ng/g, respectively, in effluent-irrigated corn-plant samples; no contaminants were detected in noneffluent irrigated corn-plant samples.

Oklahoma↗

Airport deicers: An unrecognized source of phosphorus loading in receiving waters

Airport ice control products contributed to total phosphorus (TP) loadings in a study of surface water runoff at a medium-sized airport from 2015 to 2021. Eleven airport ice control products had TP concentrations from 1–807 mg L –1 in liquid formulas, while solid pavement deicer had a TP concentration of 805 mg kg –1 . Product application data, formula TP concentrations, and surface water sampling results were used to estimate TP concentration and loading contributions from these ice control products to receiving streams. Airport ice control products were found to contribute to TP in 84% of the water samples collected at downstream sites during deicing events, and TP concentrations at those sites exceeded aquatic life benchmarks in 70% of samples collected during deicing. A receiving stream 6 km downstream had TP attributed to airport ice control sources in 78% of the samples. TP loadings at an upstream site and the receiving stream site were greatest during the largest runoff events as is typical in urban runoff, but this pattern was not always followed at airport outfall sites due to the influence of TP in deicer products. Products analyzed in this study are used at airports across the United States and abroad, and findings suggest that airport deicers could represent a previously unrecognized source of phosphorus to adjacent waterways.

Wisconsin↗