Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Acoustics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54Linked to original sources
USGS2010

A new methodology for the quantitative visualization of coherent flow structures in alluvial channels using multibeam echo-sounding (MBES)

In order to investigate the interactions between turbulence and suspended sediment transport in natural aqueous environments, we ideally require a technique that allows simultaneous measurement of fluid velocity and sediment concentration for the whole flow field. Here, we report on development of a methodology using the water column acoustic backscatter signal from a multibeam echo sounder to simultaneously quantify flow velocities and sediment concentrations. The application of this new technique is illustrated with reference to flow over the leeside of an alluvial sand dune, which allows, for the first time in a field study, quantitative visualization of large-scale, whole flow field, turbulent coherent flow structures associated with the dune leeside that are responsible for suspending bed sediment. This methodology holds great potential for use in a wide range of aqueous geophysical flows.

Geophysical Research Letters↗
USGS2010

Wind-enhanced resuspension in the shallow waters of South San Francisco Bay: Mechanisms and potential implications for cohesive sediment transport

We investigated the driving forces of sediment dynamics at the shoals in South San Francisco Bay. Two stations were deployed along a line perpendicular to a 14 m deep channel, 1000 and 2000 m from the middle of the channel. Station depths were 2.59 and 2.19 m below mean lower low water, respectively. We used acoustic Doppler velocimeters for the simultaneous determination of current velocities, turbulence, sediment concentration and fluxes. Maximum current shear velocities were 0.015 m s −1 at the station further from the channel (closer to the shore) and 0.02 m s −1 at the station closer to the channel. Peak wave-induced shear velocities exceeded 0.015 m s −1 at both stations. Maximum sediment concentrations were around 30 g m −3 during calm periods (root mean square wave height <0.15 m). During wavy periods, sediment concentrations increased to 100 g m −3 and sediment fluxes were 5 times higher than in calm conditions (0.02 g m −2 s −1 versus >0.10 g m −2 s −1 ) at the station further from the channel 0.36 m above the bed. Closer to the channel, sediment concentrations and vertical fluxes due to wind wave resuspension were persistently lower (maximum concentrations around 50 g m −3 and maximum fluxes around 0.04 g m −2 s −1 ). Most resuspension events occurred during flood tides that followed wave events during low water. Although wave motions are able to resuspend sediment into the wave boundary layer at low tide, the observed large increases in sediment fluxes are due to the nonlinear interaction of wind waves and the tidal currents.

California↗
USGS2011

3-D flow and scour near a submerged wing dike: ADCP measurements on the Missouri River

Detailed mapping of bathymetry and three-dimensional water velocities using a boat-mounted single-beam sonar and acoustic Doppler current profiler (ADCP) was carried out in the vicinity of two submerged wing dikes located in the Lower Missouri River near Columbia, Missouri. During high spring flows the wing dikes become submerged, creating a unique combination of vertical flow separation and overtopping (plunging) flow conditions, causing large-scale three-dimensional turbulent flow structures to form. On three different days and for a range of discharges, sampling transects at 5 and 20 m spacing were completed, covering the area adjacent to and upstream and downstream from two different wing dikes. The objectives of this research are to evaluate whether an ADCP can identify and measure large-scale flow features such as recirculating flow and vortex shedding that develop in the vicinity of a submerged wing dike; and whether or not moving-boat (single-transect) data are sufficient for resolving complex three-dimensional flow fields. Results indicate that spatial averaging from multiple nearby single transects may be more representative of an inherently complex (temporally and spatially variable) three-dimensional flow field than repeated single transects. Results also indicate a correspondence between the location of calculated vortex cores (resolved from the interpolated three-dimensional flow field) and the nearby scour holes, providing new insight into the connections between vertically oriented coherent structures and local scour, with the unique perspective of flow and morphology in a large river.

Missouri↗
USGS2011

A novel approach for direct estimation of fresh groundwater discharge to an estuary

Coastal groundwater discharge is an important source of freshwater and nutrients to coastal and estuarine systems. Directly quantifying the spatially integrated discharge of fresh groundwater over a coastline is difficult due to spatial variability and limited observational methods. In this study, I applied a novel approach to estimate net freshwater discharge from a groundwater-fed tidal creek over a spring-neap cycle, with high temporal resolution. Acoustic velocity instruments measured tidal water fluxes while other sensors measured vertical and lateral salinity to estimate cross-sectionally averaged salinity. These measurements were used in a time-dependent version of Knudsen's salt balance calculation to estimate the fresh groundwater contribution to the tidal creek. The time-series of fresh groundwater discharge shows the dependence of fresh groundwater discharge on tidal pumping, and the large difference between monthly mean discharge and instantaneous discharge over shorter timescales. The approach developed here can be implemented over timescales from days to years, in any size estuary with dominant groundwater inputs and well-defined cross-sections. The approach also directly links delivery of groundwater from the watershed with fluxes to the coastal environment. Copyright. Published in 2011 by the American Geophysical Union.

Massachusetts↗
USGS2012

Role of turbulence fluctuations on uncertainties of acoutic Doppler current profiler discharge measurements

This work presents a systematic analysis quantifying the role of the presence of turbulence fluctuations on uncertainties (random errors) of acoustic Doppler current profiler (ADCP) discharge measurements from moving platforms. Data sets of three-dimensional flow velocities with high temporal and spatial resolution were generated from direct numerical simulation (DNS) of turbulent open channel flow. Dimensionless functions relating parameters quantifying the uncertainty in discharge measurements due to flow turbulence (relative variance and relative maximum random error) to sampling configuration were developed from the DNS simulations and then validated with field-scale discharge measurements. The validated functions were used to evaluate the role of the presence of flow turbulence fluctuations on uncertainties in ADCP discharge measurements. The results of this work indicate that random errors due to the flow turbulence are significant when: (a) a low number of transects is used for a discharge measurement, and (b) measurements are made in shallow rivers using high boat velocity (short time for the boat to cross a flow turbulence structure).

Water Resources Research↗
USGS2012

Currents, drag, and sediment transport induced by a tsunami

We report observations of water surface elevation, currents, and suspended sediment concentration (SSC) from a 10-m deep site on the inner shelf in northern Monterey Bay during the arrival of the 2010 Chile tsunami. Velocity profiles were measured from 3.5 m above the bed (mab) to the surface at 2 min intervals, and from 0.1 to 0.7 mab at 1 Hz. SSC was determined from the acoustic backscatter of the near-bed profiler. The initial tsunami waves were directed cross shore and had a period of approximately 16 min. Maximum wave height was 1.1 m, and maximum current speed was 0.36 m/s. During the strongest onrush, near-bed velocities were clearly influenced by friction and a logarithmic boundary layer developed, extending more than 0.3 mab. We estimated friction velocity and bed shear stress from the logarithmic profiles. The logarithmic structure indicates that the flow can be characterized as quasi-steady at these times. At other phases of the tsunami waves, the magnitude of the acceleration term was significant in the near-bed momentum equation, indicating unsteady flow. The maximum tsunami-induced bed shear stress (0.4 N/m 2 ) exceeded the critical shear stress for the medium-grained sand on the seafloor. Cross-shore sediment flux was enhanced by the tsunami. Oscillations of water surface elevation and currents continued for several days. The oscillations were dominated by resonant frequencies, the most energetic of which was the fundamental longitudinal frequency of Monterey Bay. The maximum current speed (hourly-timescale) in 18 months of observations occurred four hours after the tsunami arrived.

California↗
USGS2018

Injection-induced moment release can also be aseismic

The cumulative seismic moment is a robust measure of the earthquake response to fluid injection for injection volumes ranging from 3100 to about 12 million m3. Over this range, the moment release is limited to twice the product of the shear modulus and the volume of injected fluid. This relation also applies at the much smaller injection volumes of the field experiment in France reported by Guglielmi, et al. (2015) and laboratory experiments to simulate hydraulic fracturing described by Goodfellow, et al. (2015). In both of these studies, the relevant moment release for comparison with the fluid injection was aseismic and consistent with the scaling that applies to the much larger volumes associated with injection-induced earthquakes with magnitudes extending up to 5.8. Neither the micro-earthquakes, at the site in France, nor the acoustic emission in the laboratory samples contributed significantly to the deformation due to fluid injection.

Geophysical Research Letters↗
USGS2019

Surface imaging functions for elastic reverse time migration

Reverse time migration is often used to interpret acoustic or three‐component seismic recordings by creating an image of subsurface seismic reflectors. Here I describe elastic reverse time migration imaging functions that are cast as waveform misfit sensitivity kernels of contrasts in material parameters across hypothetical seismic discontinuities, that is, specular reflectors. The proposed “surface” imaging functions are theoretically applicable to either reflected or converted waves in order to estimate the location and reflectivity of these discontinuities. The surface imaging functions, as well as volumetric sensitivity kernels that target point diffractors, are tested on sets of synthetic surface array recordings that sample the 3‐D seismic wavefield on simple 2‐D structures generated using a 2.5‐D spectral element method. These tests illustrate that in contrast with the volumetric sensitivity kernels, the reflectivity is generally dominated by a high‐amplitude peak that coincides with input locations of discontinuities. Passive recordings of microseismicity, shot gathers, or a combination thereof can be potentially interpreted with the new surface imaging functions to yield useful reflectivity images.

Journal of Geophysical Research Solid Earth↗
USGS2018

Submarine deposition of a subaerial landslide in Taan Fiord, Alaska

A large subaerial landslide entered Taan Fiord, Alaska, on 17 October 2015 producing a tsunami with runup to 193 m. We use LiDAR data to show the slide volume to be 76 + 3/−4 million cubic meters and that 51,000,000 m 3 entered Taan Fiord. In 2016, we mapped the fjord with multibeam bathymetry and high‐resolution seismic data. Landslide and postlandslide deposits extend 6 km downfjord, are up to 70 ± 11 m thick, and have a total volume of ~147,000,000 m 3 . Seismic data image a blocky landslide unit and two units deposited immediately after the landslide. The blocky landslide unit is ~65,000,000 m 3 . We infer it consists dominantly of subaerially derived material and secondarily of fjord floor sediment. The overlying units are likely megaturbidites presumably deposited within minutes to days after the landslide. We infer that these deposits dominantly consist of fjord floor material mobilized and suspended as the slide entered and traveled downfjord. The lower postlandslide unit is up to 35 ± 6 m thick, and the upper unit is up to 12 ± 3 m thick. These deposits are distinctive and will leave a lasting record of the event. This subaerial‐to‐submarine landslide deposit is distinct from other submarine landslide deposits studied in Alaskan fjords because it has a much greater thickness, larger and more angular blocks, distinctive postlandslide megaturbidites, and a higher‐amplitude acoustic signature of the blocky deposit. The tight constraints on the landslide source and deposit volumes, topography, bathymetry, and tsunami runup heights and flow directions should make this a benchmark site for landslide‐tsunami models.

Alaska↗
USGS2023

Dynamics of the December 2020 ash-poor plume formed by lava-water interaction at the summit of Kilauea Volcano, Hawaii

On 20 December 2020, after more than 2 years of quiescence at Kīlauea Volcano, Hawaiʻi, renewed volcanic activity in the summit crater caused boiling of the water lake over a period of ∼90 min. The resulting water-rich, electrified plume rose to 11–13 km above sea level, which is among the highest plumes on record for Kīlauea. Although conventional models would infer a high mass flux from explosive magma-water interaction, the plume was not associated with an infrasound signal indicative of “explosive” activity, nor did it produce a measurable ash-fall deposit. We use multisensor data to characterize lava-water interaction and plume generation during this opening phase of the 2020–21 eruption. Satellite, weather radar, and eyewitness observations revealed that the plume was rich in water vapor and hydrometeors but transported less ash than expected from its maximum height. Volcanic lightning flashes detected by ground-based cameras were confined to freezing altitudes of the upper cloud, suggesting that the ice formation drove the electrification of this plume. The low acoustic energy from lava-water interaction points to a weakly explosive style of hydrovolcanism. Heat transfer calculations show that the lava to water heat flux was sufficient to boil the lake within 90 min. Limited mixing of lava and water inhibited major steam explosions and fine fragmentation. Results from one-dimensional plume modeling suggest that the models may underpredict plume height due to overestimation of crosswind air-entrainment. Our findings shed light on an unusual style of volcanism in which weakly explosive lava-water interaction generated an outsized plume.

Hawaii↗
USGS2023

Time-lapse seafloor surveys reveal how turbidity currents and internal tides in Monterey Canyon interact with the seabed at centimeter-scale

Here we show how ultra-high resolution seabed mapping using new technology can help to understand processes that sculpt submarine canyons. Time-lapse seafloor surveys were conducted in the axis of Monterey Canyon, ∼50 km from the canyon head (∼1,840 m water depth) over an 18-month period. These surveys comprised 5-cm resolution multibeam bathymetry, 1-cm resolution lidar bathymetry, and 2-mm resolution stereophotographic imagery. Bathymetry data reveal centimeter-scale textures that would be undetectable by more traditional survey methods. Upward-looking Acoustic Doppler Current Profilers at the site recorded the flow character of internal tides and the passage of three turbidity currents, while sediment cores collected from the site record flow deposits. Combined with flow and core data, the bathymetry shows how turbidity currents and internal tides modify the seabed. The turbidity currents drape sediment across the site, infilling bedform troughs and smoothing erosional features carved by the internal tides (e.g., rippled scours). Turbidity currents with speeds of 0.9–3.3 m/s failed to cause notable bedform movement, which is surprising given that flows with similar speeds produced rapid bedform migration elsewhere, including the upper Monterey Canyon. The lack of migration may be related to the character of the underlying substrate or indicate that turbidity currents at the site lack dense, near-bed layers. The scale of scours produced by the internal tides (≤0.7 m/s) approaches the scale of features recorded in the ancient rock record. Thus, these results illustrate how the scale gap between seabed mapping technology and the rock record may eventually be bridged.

California↗
USGS2024

Laboratory hydrofractures as analogs to tectonic tremors

The fracture of Earth materials occurs over a wide range of time and length scales. Physical conditions, particularly the stress field and Earth material properties, may condition rupture in a specific fracture regime. In nature, fast and slow fractures occur concurrently: tectonic tremor events are fast enough to emit seismic waves and frequently accompany slow earthquakes, which are too slow to emit seismic waves and are referred to as aseismic slip events. In this study, we generate simultaneous seismic and aseismic processes in a laboratory setting by driving a penny-shaped crack in a transparent sample with pressurized fluid. We leverage synchronized high-speed imaging and high-frequency acoustic emission (AE) sensing to visualize and listen to the various sequences of propagation (breaks) and arrest (sticks) of a fracture undergoing stick-break instabilities. Slow radial crack propagation is facilitated by fast tangential fractures. Fluid viscosity and pressure regulate the fracture dynamics of slow and fast events, and control the inter-event time and the energy released during individual fast events. These AE signals share behaviors with observations of episodic tremors in Cascadia, United States; these include: (a) bursty or intermittent slow propagation, and (b) nearly linear scaling of radiated energy with area. Our laboratory experiments provide a plausible model of tectonic tremor as an indicative of hydraulic fracturing facilitating shear slip during slow earthquakes.

AGU Advances↗
USGS2023

UAS-Based Observations of Infrasound Directionality at Stromboli Volcano, Italy

Infrasound (low frequency sound waves) can be used to monitor and characterize volcanic eruptions. However, infrasound sensors are usually placed on the ground, thus providing a limited sampling of the acoustic radiation pattern that can bias source size estimates. We present observations of explosive eruptions from a novel uncrewed aircraft system (UAS)-based infrasound sensor platform that was strategically hovered near the active vents of Stromboli volcano, Italy. We captured eruption infrasound from short-duration explosions and jetting events. While potential vertical directionality was inconclusive for the short-duration explosion, we find that jetting events exhibit vertical sound directionality that was observed with a UAS close to vertical. This directionality would not have been observed using only traditional deployments of ground-based infrasound sensors, but is consistent with jet noise theory. This proof-of-concept study provides unique information that can improve our ability to characterize and quantify the directionality of volcanic eruptions and their associated hazards.

Stromboli Volcano↗
USGS2024

Siting considerations for satellite observation of river discharge

With growing global capability for satellite measurement of river discharge (flow) comes a need to understand and reduce error in satellite-based discharge measurements. Satellite-based discharge estimates are based on measurements of water surface width, elevation, slope, and potentially velocity. Site selection is important for reducing error and uncertainty in both conventional and satellite-based discharge measurements because geomorphic river characteristics have strong control over the relationships between discharge and width, water surface elevation (or depth), slope, and velocity. A large ground-truth data set of 8,445 conventional hydraulic measurements, collected by acoustic Doppler current profilers at 503 stations in the United States, was developed and quality assured to examine correlation between river discharge and water surface width, depth, velocity, and cross-sectional area. A separate database of river surface slope and discharge time-series was developed from paired continuous monitoring stations to examine slope-discharge correlations. Results show that discharge correlates most strongly with velocity, cross-sectional area, depth, width, and slope, in that order. Uncertainty of satellite discharge estimates is affected by observed hydraulic variable and reach-specific variability in observed variable(s) characteristics including range of variability, georegistration accuracy, and stability over time of relationships between discharge and observed hydraulic variable.

Water Resources Research↗
USGS2025

The first instrumentally detected hydrothermal explosion in Yellowstone National Park

Hydrothermal explosions are one of the geological hazards most likely to impact people in Yellowstone National Park, but their frequency is poorly known. Infrasound and seismic sensors identified an explosion in Norris Geyser Basin on 15 April 2024, at 14:56 MDT (20:56 UTC)—the first instrumentally detected hydrothermal explosion in the Yellowstone region. The event affected an area tens of meters across, resulting in fractured ground, a shallow explosion crater, and a field of ejecta. There were no immediate geophysical precursors, but in the preceding years elevated discharge of thermal water altered the color, temperature, and level of a nearby small lake. Expanded seismo-acoustic monitoring in Yellowstone National Park could be useful for detecting small hydrothermal explosions and constraining their frequency, magnitude, energy release, and locations—information that could be used to better assess and mitigate hazards for the millions of people that visit the park each year.

Wyoming↗
USGS2026

Interplay between tectonics and submarine mass transport deposits in Cortes Basin: New high-resolution geophysics in the Outer California Borderland

The Outer California Borderland (OCB) is an active transform plate boundary offshore Southern California, where the relationship between faulting and submarine mass transport deposits (MTDs) remains poorly understood. Onshore paleoseismic data provide high-resolution earthquake records, whereas marine geophysical data capture longer-term histories. Offshore fault systems pose hazards to infrastructure and dense coastal populations, particularly when linked to submarine landslides. We present new high-resolution geophysical data set (cruise SR2303), including bathymetric and CHIRP sub-bottom data integrated with legacy seismic reflection data and chronostratigraphic constraints from ODP Site 1012 to examine Quaternary MTD recurrence and tectonic controls in the Cortes Basin, OCB. Bathymetry shows deformational features, including slide scarps and previously unmapped fault segments with evidence of Holocene activity. CHIRP profiles reveal 10 stacked MTDs in the East Cortes Basin and 8 in the West Cortes Basin, spanning ∼752 ka with an average recurrence of ∼83.6 ± 1 ka. Acoustic imaging shows 7 MTD intervals coinciding with fault offset increments and fault growth suggesting earthquake-triggered mass wasting. A strong association between MTD occurrences and sea-level extremes also supports glacio-eustatic contribution to slope failure. Stratigraphic correlations suggest quasi-synchronous MTDs across the eastern and western areas, likely triggered by larger eathquakes in the Quaternary. Although the identified MTDs occur relatively far from the Southern California coast, they still pose a potential tsunamigenic hazard requiring further assessment. Moreover, if linked to earthquakes along major strike-slip faults, for example, the Ferrelo fault, the MTDs may provide valuable proxies to constrain rupture scenarios and fault connectivity within the understudied OCB.

California↗
USGS2026

Fully contained laboratory earthquakes: The effect of asperity aspect ratio and free surfaces

Corner frequency ( f c ) and seismic moment ( M 0 ) are key parameters derived from seismic signals that are used to characterize earthquake stress drop, rupture area, and slip. These parameters are also affected by fault geometry and boundary conditions. However, the systematic study of these effects in laboratory settings has been challenging. This study presents laboratory earthquake experiments that examine how rupture dynamics are influenced by (a) the aspect ratio of rectangular PMMA velocity-weakening (VW) asperities surrounded by the Teflon velocity-strengthening (VS) patches, and (b) whether the sides of a VW asperity are confined with VS patches or are free surfaces. We found that increasing confinement by reducing free surfaces or increasing the VW asperity aspect ratio stabilizes fault slip, so that higher normal stress is required to transition from aseismic to seismic slip. Increased confinement and high aspect ratios also reduced M 0 and increased f c , both of which were determined from the radiated seismic waves. M 0 and f c were primarily controlled by the shorter dimension of the VW asperity. Analysis of high-frequency acoustic emission signals revealed that ruptures on high-aspect-ratio VW asperities propagated more unidirectionally, whereas ruptures on square VW asperities were more complex. Further, the high-aspect-ratio asperities were more likely to be eroded by surrounding VS regions while low-aspect-ratio asperities were more likely to rupture into the VS surroundings. These results demonstrate that both the confinement from surrounding stable areas and the geometry of the seismogenic patch can affect rupture nucleation, propagation, and seismic source characteristics.

JGR Solid Earth↗
USGS2012

Fractal properties of tremor and gas piston events observed at Kilauea Volcano, Hawaii

Studies the fractal properties of shallow volcanic tremor and gas piston events associated with magma degassing at Kilauea Volcano, Hawaii, using data from two dense short-baseline arrays of seismographs deployed near the active crater of Puu Oo on the east rift of the volcano. The existence of a categorically stable attractor characterizing both types of activities strongly suggests that the excitation mechanism of tremor is similar to that of gas piston events, which in turn are correlated with visual observations at the volcanic vent. Low values derived for the dimension of the attractor in phase space points to significant self-organization in the process of generation of tremor and offers general constraints on the dimensionality of attractors derived from models of acoustic emission associated with magma flow, vesiculation, and degassing. -from Authors

Hawaii↗