SEARCH · Geology Reports

Results for “Annual Review of Earth and Planetary Sciences”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,695 records · Page 52Linked to original sources

USGS2026

Status and understanding of groundwater quality in the San Joaquin Valley Kern County subbasin domestic-supply aquifer study unit, 2022—California GAMA Priority Basin Project

The quality of water accessed by domestic wells (here referred to as domestic groundwater resources) in the San Joaquin Valley Kern County subbasin (basin number 5-022.14) was assessed as part of the California Groundwater Ambient Monitoring and Assessment (GAMA) Program Priority Basin Project (GAMA-PBP), in cooperation with the California State Water Resources Control Board. Kern County is at the southern end of the San Joaquin Valley in California, and about 30,000 residents are estimated to use privately owned domestic wells for drinking water. Domestic wells typically draw from shallower parts of the aquifer system than public-supply wells and can be more vulnerable to effects from surface activities. Kern County is host to a highly productive agricultural industry, with Bakersfield as the main urban center. The Kern River runs through Bakersfield from the southern Sierra Nevada and intersects the Kern Water Bank, one of the largest groundwater banking operations in California, at the Kern River Intertie. The section of the Kern River running through the Kern Water Bank is dry most years. Kern County also encompasses some of the most productive oil and gas basins in California, with extensive underground and surface disposal of oil-field wastewater. This study was based on data collected from 33 sites sampled by the U.S. Geological Survey for the GAMA-PBP in 2022. To provide context for the water quality assessment, measured concentrations were compared to regulatory and non-regulatory health-based and aesthetic benchmarks. A grid-based method was used to estimate the proportions of the groundwater resources used for domestic-supply wells that have water-quality constituents below (low relative concentration), approaching (moderate relative concentration), or above (high relative concentration) benchmark concentrations. At least one measured constituent with a regulatory benchmark was categorized as having a high relative concentration in 72 percent of the aquifer area used for domestic groundwater resources. Inorganic constituents were detected at high concentrations in 45 percent of the domestic groundwater resources, and the constituents detected above regulatory benchmarks were arsenic, nitrate, and uranium. At least one organic constituent was detected at high concentrations in 41 percent of the domestic groundwater resources, and the constituents exceeding regulatory benchmarks were the fumigants 1,2,3-trichloropropane (1,2,3-TCP), 1,2-dibromo-3-chloropropane (dibromochloropropane [DBCP]), 1,2-dibromoethane (EDB), and the per-and polyfluoroalkyl substance (PFAS) perfluorooctanesulfonate. The disinfection by-product chloroform, the fumigant 1,2-dichloropropane, the herbicides atrazine and hexazinone, and the herbicide degradates 2-chloro-6-ethylamino-4-amino-s-triazine, 2-chloro-4,6-diamino-s-triazine, 4-hydroxychlorothalonil, and metolachlor sulfonic acid were detected in more than 10 percent of domestic groundwater resources, but concentrations did not exceed regulatory benchmarks. Land use, groundwater age (fraction of modern water and mean age), and geochemical environment (oxic or anoxic conditions, pH, alkalinity) were associated with the distribution of high relative concentrations of inorganic and organic constituents. Young, oxygenated water is recharged along the Kern River and adjacent recharge ponds, or as irrigation water in the agricultural areas. High concentrations of nitrate and volatile organic compounds occurred in the oxic water in urban and agricultural areas. The fumigants 1,2,3-TCP, DBCP, and EDB were reported throughout the agricultural areas, whereas chloroform, tetrachloroethene, and PFAS were associated with urban land use. High uranium concentrations were associated with young, modern groundwater in agricultural areas with low pH and high bicarbonate. Total dissolved solids increased with distance from the Kern River, as the contributions of fresh, oxic water decreased. High concentrations of arsenic were present in older anoxic or alkaline groundwater away from areas of recharge. Overall, groundwater age, redox conditions, and the source of recharge as a result of different land uses contribute to large aquifer-scale portions of domestic groundwater resources that exceed health-based benchmarks for nitrate, uranium, and fumigant concentrations.

California↗

USGS2025

Fiber-optic distributed temperature sensing of hydrologic processes—Diverse deployments and new applications by the U.S. Geological Survey

Fiber-optic distributed temperature sensing instruments harness the temperature-dependent properties of glass to measure temperature continuously along optical fibers by using precise pulses of laser light. In the mid-2000s, this technology was refined for environmental monitoring purposes such as snowpack-air exchange, groundwater/surface-water exchange, and lake-water stratification. Fiber-optic distributed temperature sensing has revealed unprecedented details about preferential flow processes; however, the method is labor intensive and requires specific training, resulting in limited use by the broader water community. With the ongoing national implementation of the U.S. Geological Survey Next Generation Water Observing System, there has been renewed interest in harnessing the unique spatiotemporal monitoring capabilities of fiber-optic distributed temperature sensing. This fact sheet briefly describes this technology, highlights uses by the U.S. Geological Survey, and discusses current applications and future opportunities.

Fact Sheet↗

USGS1976

Uranium and trace elements in stream sediments as an exploration tool

More than 45 trace elements have been reported in anomalous amounts in the uranium ores. The specific suite of elements associated with any one uranium deposit varies according to deposit type and geologic province. The primary geochemical halo of uranium and associated trace elements in the host rock, together with secondary dispersion halo in soils and alluvium, offers a potential geochemical exploration target. Sediment from streams near low-grade uranium occurrences in arkosic sandstone of the Denver basin, Colorado, and sediment from streams in the igneous and metamorphic terrace near the Midnite mine of eastern Washington have been analyzed for acid-extractable U, Cu,Pb, Zn, Ni, Co, Fe, Mn, Mo, Cd, Cr, Ag, V, and Se, and for total Fe, Mn, Hg, As, and organic C. The -80 mesh fraction of the alluvium downstream from a small uraniferous limonite occurrence in the Denver basin shows anomalous concentrations of U, Pb, As, Ni, Mo, V, Zn, and Se. Anomalous concentrations of U persist farther downstream (as much as 1,000 m) than any of the trace elements. In another stream system southeast of Denver, above-background levels of U, Pb, As, Zn, V, Fe, and Mn occur near a uranium anomaly (defined by other methods) which has no surface mineralization. In the Midnite mine area, sediments of streams draining prospect areas showed anomalous concentrations of uranium (as much as 10 times background), but no accompanying anomalous trace-element concentrations, although analyses of Midnite mine ores show that a broad suite of trace elements are associated with uranium.

Open-File Report↗

USGS2025

Quantitative evaluations of earthquake early warning performance using “Did You Feel It?” and post-alert surveys

We examine responses to the U.S. Geological Survey’s “Did You Feel It?” (DYFI) survey and its companion earthquake early warning (EEW) questionnaire to assess the performance of the U.S. ShakeAlert EEW system directly from the alert recipients’ perspectives. ShakeAlert rapidly detects earthquakes and develops alert information, but as official alert delivery partners issue these alerts, it is thus difficult to determine how many people were alerted and when. We investigate DYFI reports for six California earthquakes that had EEW alerts and substantial responses to the DYFI EEW questionnaire. Comparisons of ShakeAlert predictions to reported intensities demonstrate that magnitude estimation accuracy is not necessarily indicative of ground-motion prediction accuracy. Perceived warning time distributions indicate that estimating maximum-expected warning times using the S-wave arrival is a reasonable assumption when discussing public EEW performance. However, we also find many reports of shorter warning times, late alerts, and missed alerts than expected based on ShakeAlert publication times, suggesting alert delivery latencies are substantial and highly variable. The novelty of our analysis is that we demonstrate that the DYFI EEW survey provides useful EEW efficacy information—independent of the specific alerting pathway—that can be used to inform our choices for conveying EEW performance.

California↗

USGS2024

Testing rate‐and‐state predictions of aftershock decay with distance

We analyze aftershocks of the 2019 M 7.1 Ridgecrest mainshock and isolated M 5–6 mainshocks in southern California to test predictions made by the rate‐and‐state friction model of Dieterich (1994) . Rate‐and‐state friction predicts that the seismicity rate after a stress step follows Omori decay, where the Omori c ‐value, which is the saturation in aftershock rate observed at small times, is larger for smaller stress steps. Put in the context of an aftershock sequence, this predicts that the Omori c ‐value will be systematically larger at greater distances from the mainshock. To our knowledge, this predicted effect has not been observed. In part this may be because the Omori c ‐value is difficult to measure because it often reflects short‐term catalog incompleteness rather than a true saturation in aftershock rate. We explore the dependence of the Omori c ‐value on the distance to the mainshock by applying the “ a ‐positive” method ( van der Elst and Page, 2023 ). This method is insensitive to short‐term aftershock incompleteness and allows resolution of the true aftershock rate deep into the mainshock coda. For aftershocks of the Ridgecrest mainshock and stacked M 5–6 mainshocks, we observe systematic differences in early aftershock rates, relative to mainshock distance, consistent with the predictions of rate‐and‐state friction. Furthermore, for the larger Ridgecrest dataset, we observe that aftershocks nearer to the mainshock start earlier, and we resolve a flattening of the Omori curve consistent with a larger Omori c ‐value for the farthest aftershocks, as predicted by Dieterich (1994) .

Seismological Research Letters↗

USGS2025

Tracing fluid evolution during batholith and deposit formation: In-situ and bulk rock Mo isotopes from the Questa porphyry Mo deposit, New Mexico, USA

The Oligocene Questa porphyry Mo deposit, located in New Mexico, USA, is a well-characterized system that formed over 400 kyr, punctuating the 8 Myr formation of the Questa-Latir batholith. Detailed sampling of the intrusions and minerals associated with magmatichydrothermal mineralization, as well as bookending barren intrusions, allows for examination of the Mo isotope record of the deposit and its host batholith. Through this established chronologic framework, such data can yield insights into the metallogenesis of deposit formation and long-term magma genesis evolution for upper crustal magmatism. The Mo isotopic compositions of barren intrusions yield a younging trend towards lighter δ 98 Mo. However, intrusions associated with Mo deposit formation yield heavier δ 98 Mo relative to barren magmatism, by up to 2.0‰. This indicates that they were affected by an isotopically heavy and Mo-rich fluid. The in-situ data from molybdenite covers the range observed in mineralized bulk rocks. However, individual samples consistently yield Mo isotopic variations of 0.4‰ to 0.5‰. The consistency of the δ 98 Mo variation in in-situ analyses of molybdenite within hand samples and individual mineral grains is likely the result of MoS 2 crystallization in a closed system and reflects an almost complete precipitation of Mo.

New Mexico↗

USGS2025

Seismic moment and local magnitude scales in Ridgecrest, CA from the SCEC/USGS Community Stress Drop Validation Study

We illustrate the systematic difference between moment magnitude and local magnitude caused by underlying earthquake source physics, using seismic moments submitted to the Statewide California Earthquake Center/United States Geological Survey Community Stress Drop Validation Study 2019 Ridgecrest data set. While the relationship between seismic moment and moment magnitude ( M or M w ) of log 10 ( M 0 ) ~ 1.5* M is uniformly valid for all earthquake sizes by definition (Hanks and Kanamori, 1979), the relationship between local magnitude M L and moment is itself magnitude dependent. For moderate events, ~3< M < ~6, M and M L are coincident; for earthquakes smaller than ~3, M L ~ 1.0 log 10 M 0 (Hanks and Boore, 1984). This is a physical consequence of the corner frequency fc becoming larger than the upper frequency of observation and implies that M L and M differ systematically by a factor of 1.5 for these small events. While this idea is not new, we propose a new, continuous relationship between local magnitude and moment, for magnitudes 2 to 6 which extrapolates to smaller and larger magnitudes, applicable to southern California specific to the Ridgecrest region. We make use of the plethora of seismic moments as submitted by many participants of the Community Stress Drop study, compared to the Southern California Seismic Network (SCSN) catalog magnitudes. Overall, the seismic moments in the Community Study recover moment magnitude well, so we use our new M L - M 0 to convert M L to M , refining the SCSN operational M Lr scale. This systematic difference of 50% in slope between local and moment magnitude at small magnitudes has implications for spectral stress drop estimates, earthquake ground motion modeling, as well as other magnitude scales and earthquake occurrence statistics.

California↗

USGS2024

Post-glacial stratigraphy and late Holocene record of great Cascadia earthquakes in Ozette Lake, Washington, USA

Ozette Lake is an ~100-m-deep coastal lake located along the outer coast of the Olympic Peninsula (Washington, USA); it is situated above the locked portion of the northern Cascadia megathrust but also relatively isolated from active crustal faults and intraslab earthquakes. Here we present a suite of geophysical and geological evidence for earthquake-triggered mass transport deposits (MTDs) and related turbidite deposition in Ozette Lake since ca. 14 ka. Comprehensive high-resolution bathymetry data, seismic reflection profiles, and sediment cores are used to characterize the post-glacial stratigraphic framework and examine paleoseismic evidence in the lacustrine sediments. Stacked sequences of MTDs along the steep eastern flanks of the lake appear to grade basin-ward from thick, chaotic, blocky masses to thin, parallel-bedded turbidite beds. The discrete turbidite event layers are separated by fine-grained (silt and clay) lake sedimentation. The event layers are observed throughout the lake, but the physical characteristics of the deposits vary considerably depending on proximity to primary depocenters, steep slopes, and subaqueous deltas. A total of 30–34 event deposits are observed in the post-glacial record. Radiometric dating was used to reconstruct a detailed sedimentation history over the last ~5.5 k.y., develop an age model, and estimate the recurrence (365–405 yr) for the most recent 12 event layers. Based on sedimentological characteristics, temporal overlap with other regional paleoseismic chronologies, and recurrence estimates, at least 10 of the dated event layers appear to be sourced from slope failures triggered by intense shaking during megathrust ruptures; the recurrence interval for these 10 events is 440–560 yr. Thus, Ozette Lake contains one of the longest and most robust geological records of repeated shaking along the northern Cascadia subduction zone.

Washington↗

USGS2024

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri and Mississippi Rivers on the periphery of Missouri, June 13–22, 2022

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near seven bridges at six highway crossings of the Missouri and Mississippi Rivers on the periphery of Missouri from June 13–22, 2022. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 feet longitudinally and generally extending laterally across the active channel from bank to bank during minor flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a minor flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All bridge sites in this study were surveyed and documented in previous studies. Although partial exposure of substructural support elements was observed at several piers, at most sites the exposure most likely is minimal compared to the overall substructure that remains buried in bed material at these piers. The notable exceptions are piers 12 and 13 at structure L0135 on State Highway 51 at Chester, Illinois, where the bedrock material was fully exposed around the piers. The average difference between the bathymetric surfaces between 2022 and 2018 varied from 0.41 foot higher to 1.86 feet lower. Between 2022 and 2014, the average difference between the bathymetric surfaces varied from 1.02 feet higher to 4.69 feet lower. Only the two sites on the Missouri River and the Caruthersville site were surveyed in 2011; for those sites, the average difference between the bathymetric surfaces varied from 5.83 feet higher to 1.34 feet lower. The most substantial overall net gain of sediment in a reach was between 2011 and 2022 at structure A1700 near Caruthersville, Mo. (site 38). This result was expected because structure A1700 is downstream from the confluences of the Missouri and Ohio Rivers, and therefore subject to the largest streamflows, the largest streamflow fluctuations, and the most substantial sediment flux, as has historically been observed at this site. The presence of riprap blankets, pier size and nose shape, and alignment to flow had a substantial effect on the size of the scour hole observed for a given pier. Piers that were surrounded by riprap blankets had scour holes that were substantially smaller (to nonexistent) compared to piers at which no rock or riprap were present. New riprap blankets were surveyed at pier 3 of structure L0098 at Brownville, Nebraska, and at piers 15–18 of structure A1700 near Caruthersville, Mo., that effectively mitigated the scour holes historically observed at these piers. Narrow piers having round or sharp noses that were aligned with flow often had scour holes that were difficult to discern from nearby bed features, whereas piers having wide or blunt noses resulted in larger, deeper scour holes. Several of the structures had piers that were skewed to primary approach flow. Scour holes near these piers consistently displayed greater depth on the side of the pier with impinging flow and deposition on the leeward side of the pier.

Missouri↗

USGS2025

Analysis of aquifer framework and properties, Alvahs Lane well field, Cutchogue, New York

The U.S. Geological Survey, in cooperation with the Suffolk County Water Authority, evaluated the aquifer transmissivity and storage properties at the Alvahs Lane well field north of the village of Cutchogue, New York. This analysis of aquifer properties provides the Suffolk County Water Authority with hydrogeologic information needed to develop water supplies to meet the increasing water demands of the residents of Suffolk County, New York. An aquifer test was conducted at the Alvahs Lane well field from October 18 through October 21, 2022, when a production well was pumped at 550 gallons per minute for about 24 hours, and groundwater-level drawdown and recovery were measured in two monitoring wells. The three wells are screened in a glaciofluvial aquifer under unconfined (water table) conditions. Drawdown and recovery data were analyzed with an analytical solution for partial penetration and delayed yield in an unconfined aquifer to provide estimates of the glaciofluvial aquifer properties. Inclusion of lateral aquifer boundaries was not necessary for the analysis to result in satisfactory matches with the observed water-level responses. Aquifer transmissivity was estimated at 32,000 feet squared per day. Assuming a saturated aquifer thickness of 120 feet, this result is equivalent to a horizontal hydraulic conductivity value of 270 feet per day. Specific yield was estimated at 0.15 (dimensionless). The estimated properties are consistent with those of a highly transmissive unconfined aquifer.

New York↗

USGS2024

Generalized potentiometric maps of the Fort Union, Hell Creek, and Fox Hills aquifers within the Standing Rock Reservation

Generalized potentiometric surfaces of the Fort Union, Hell Creek, and Fox Hills aquifers were constructed to assess the groundwater resources of the Standing Rock Reservation. Additionally, this information can provide water managers with tools and data to effectively manage water resources in the future. Previous studies that mapped the geology and hydrogeology of the area at differing scales were used to confirm in which aquifer the study wells were completed. Water-level data from wells are provided by the U.S. Geological Survey Groundwater System Inventory database, the South Dakota Department of Agriculture and Natural Resources, and the North Dakota Department of Water Resources. Hydrographs were constructed for five selected observation wells to evaluate historical water-level fluctuations and trends. Hydrographs for the Hell Creek aquifer showed a flat trend with a rise in 2020. Hydrographs for the deeper Fox Hills aquifer showed that water levels fluctuated in response to climatic conditions and demonstrated an increasing trend in water-level elevations starting in 2010. Hydrographs were not constructed for any wells completed in the Fort Union Formation because none of the wells had continuous long-term measurements. Generalized potentiometric surfaces, constructed from interpolating water-level elevations, gave insight into groundwater flow directions. Groundwater in the Fort Union aquifer likely flows radially outward from the northwest part of the study area to the northeast and south-southeast parts. Groundwater in the Hell Creek aquifer generally flows from higher elevations in the northwest towards lower areas, where surface-water tributaries have incised into the aquifer. Groundwater in the Fox Hills aquifer likely flows from higher elevations in the west, southwest, and central parts of the study area towards the valleys of the Grand River and Missouri River. Most wells used for constructing potentiometric maps had only one recorded water-level measurement from drillers at the time of well construction. These measurements are often subject to error because the well is still recovering and because of spatial limitations of data availability. Also, because single water-level measurements were recorded at different points in time, additional uncertainty is introduced by fluctuating climatic conditions effect on water levels. Potentiometric map interpretation limitations are a result of areas with sparse data. Limitations also arise from potentiometric surfaces generalizing a complex and dynamic hydrogeologic system; however, the generalized potentiometric surface maps can be used to assist water managers and can help prioritize locations for future monitoring in areas with high uncertainty from sparse existing data.

North Dakota, South Dakota↗

USGS2025

Multi-scale geophysical mapping of the brine and bedrock surfaces along the Dolores River, Paradox Valley, Colorado, December 2023

Total dissolved solids derived from salt dome–sourced brine in the underlying alluvial aquifer substantially increase with distance in the reach of the Dolores River that passes through Paradox Valley in southwestern Colorado. The area has been the site of salinity control operations since the 1990s to reduce salt loading to the downstream Colorado River. Previous airborne and ground/water-based electromagnetic (EM) geophysical data have successfully mapped the top of the brine surface, albeit with relatively coarse near-surface resolution and limited spatial coverage. This present December 2023 study used ground-based high-resolution EM and passive seismic (horizontal-to-vertical spectral ratio, HVSR) tools to map in detail the depth and thickness of the brine zone in the alluvial aquifer (top of the brine down to bedrock contact) in areas immediately surrounding the Dolores River where previous airborne EM (AEM) results indicated brine within 10 m of land surface. Results indicate the deepest bedrock is generally associated with the shallowest brine and local depressions in the collapse breccia (caprock to the Paradox Formation salt) may facilitate vertical migration of brine into the alluvial aquifer. Additionally, the ground-based EM mapping corroborated general patterns in depth to brine that were observed in previous AEM results while also revealing additional detail, including suspected focused brine discharge zones to the Dolores River. A river-based survey wherein EM data, channel depth and river water–specific conductance information were collected augmented these findings and indicated specific areas on both the western and eastern sides of the river where focused brine discharge may occur. This study comprises a large-scale, ground- and water-based geophysical mapping effort, including hundreds of HVSR soundings and 100s of kilometres of EM data, which were successfully translated into digital brine and bedrock surfaces that could be incorporated into groundwater modelling efforts, future well siting or other decision-making.

Colorado↗

USGS2025

Evaluation of solid bitumen created from marine oil shale bituminite under hydrous and anhydrous pyrolysis conditions

To test the influence of environmental conditions on aromaticity of solid bitumen generated during petroleum generation, four organic-rich (26–36 wt% total organic carbon) oil shale samples collected from the Neoproterozoic–Lower Cambrian restricted marine Salt Range Formation in the upper Indus Basin, Pakistan, were pyrolyzed under hydrous and anhydrous conditions. Experiments used closed system batch reactors at subcritical water temperatures between 300 and 370°C for 72 h. Thermal conversion of bituminite in the Salt Range oil shales created a newly formed solid bitumen, similar to previous observations from experiments on the Eocene lacustrine Green River Formation Mahogany zone oil shale. Newly formed solid bitumen in the Salt Range Formation oil shales generally has higher reflectance (R o ) in hydrous residues compared to anhydrous experiments subjected to the same time-temperature conditions, also similar to prior observations. This finding supports the hypothesis that radical disproportionation is favored in the presence of hydrogen contributed by water, promoting aromatization in the solid bitumen residue with concomitant increased expulsion of saturated hydrocarbons. Indigenous solid bitumen (and vitrinite in a comparison sample) also shows higher reflectance values in hydrous versus anhydrous residues, indicating that additional aromatization in the presence of exogenous hydrogen occurs both in newly formed organic matter and in organic matter that is present throughout the experiment. Despite similarities in their bulk rock geochemical screening parameters, R o evolution shows different trajectories amongst the four Salt Range oil shales, suggesting as-yet undetermined differences in kinetic properties which are probably related to differences in a priori chemical composition. These results have implications for the use of solid bitumen reflectance (BR o ) as a thermal proxy, suggesting BR o values and appearance could vary as a function of the concentration of water. Variation in water concentration may be present at the reservoir or formation scale, but may also be present at a much finer scale in tight oil shales where permeability is several orders of magnitude lower than conventional reservoirs. Therefore, local variations in the presence of water potentially could explain substantial variation in BR o values and appearance in closely spaced source rock samples and even within an individual microscope field.

Journal of Analytical and Applied Pyrolysis↗

USGS2024

Mesoproterozoic to Paleozoic tectonics, Pleistocene landforms, and Holocene seismicity in the Blue Ridge: Results from integrated studies of the 9 August 2020, Mw 5.1 earthquake area near Sparta, North Carolina, USA

This field trip examines the results of integrated geologic studies of the 9 August 2020, M w 5.1 earthquake near Sparta, North Carolina, USA. The earthquake generated ~4 km of coseismic surface rupture of the Little River fault and uplifted a surface area of ~11 km 2 . The Little River fault is a thrust fault oriented 110–130°/45–70°SW, and mapped fault segments are en echelon with scarp heights from <5–30 cm. The epicenter is in polydeformed rocks of the Ashe and Alligator Back Metamorphic Suites in the eastern Blue Ridge. Bedrock structure formed during multiple Paleozoic orogenies; the regional foliation strikes NE-SW and dips SE (mean orientation 063°/52°SE). Mapping identified late Paleozoic veins and shear zones, a regional joint set striking 330–340° and 250–240°, and brittle faults that cut the Paleozoic foliation. Brittle faults oriented similar to the Little River fault are mapped up to 4 km along strike from the coseismic rupture along Bledsoe Creek valley, and the combined length of the Little River fault system is ~8 km. Paleoseismic trenches across the Little River fault corroborate the reactivation of an older fault by the 2020 earthquake and reveal two events during late Pleistocene (<50 ka). Surficial mapping identified several terrace deposits, including a deposit along Bledsoe Creek that yielded a 26 Al/ 10 Be isochron burial age of 0.46 ± 0.13 Ma and overlies a brittle fault, thus constraining the timing of movement of the fault at that location. Paleoliquefaction studies document soft-sediment deformation features in alluvium that may represent paleoseismic events. Collectively, these results highlight long-lived paleoseismicity of the Blue Ridge and that the 9 August 2020 earthquake reactivated an older, suitably oriented brittle fault in the bedrock. The Little River fault is an example of a previously unknown but active fault lying outside of known seismic zones with demonstrated recurrence of paleo-ruptures, raising questions about the assumption that damaging earthquakes are limited to areas of ongoing background seismicity, which is counter to seismic hazard assessments in the eastern United States. Bedrock mapping separates eastern Blue Ridge lithostratigraphy of the Lynchburg Group and Ashe and Alligator Back Metamorphic Suites into separate fault-bound packages juxtaposed over various 1.3–1.0 Ga basement rocks of the northern French Broad massif by the Gossan Lead fault.

North Carolina↗

USGS2024

Three-dimensional hydrogeologic framework model of the Russian River watershed, California

The Russian River watershed is in northern Sonoma County and southern Mendocino County, California, in the northern part of the California Coast Ranges. The Russian River serves as a supply for agricultural irrigation and for municipal, domestic, and commercial uses. Through a cooperative agreement with the California State Water Resources Control Board and Sonoma County Water Agency, the U.S. Geological Survey has completed studies to better understand the hydrogeologic system and develop numerical hydrologic modeling tools to evaluate and aid in managing groundwater resources. This report focuses on the development of a digital three-dimensional hydrogeologic framework model of the Russian River watershed for use in groundwater resource assessment and numerical models. The digital three-dimensional hydrogeologic framework model of the Russian River watershed portrays the altitude, thickness, and extent of five hydrogeologic units. These five hydrogeologic units include (1) a basement unit, (2) the Sonoma Volcanics, (3) a consolidated sedimentary rock unit, (4) an unconsolidated sediment unit, and (5) channel alluvium. Model input data were compiled from published geologic maps, interpreted well data, and a model of the top of basement derived from gravity data. These data were used to construct surfaces that represent the upper and lower subsurface boundaries of each hydrogeologic unit. Top surfaces were created for the five hydrogeologic units and then stacked in three dimensions to create a solid-volume digital model. The digital three-dimensional hydrogeologic framework model described in this report and the corresponding data represent the generalized geometry of the subsurface geologic units; the model reproduces the input geologic data with reasonable accuracy and is consistent with previously published subsurface conceptualizations of the region. The model indicates the overall geometry of the basement within the watershed and the spatial extent, altitude, and thickness of the basin-filling units. The hydrogeologic framework model is at a scale and resolution appropriate for use as the foundation for a numerical hydrologic model of the study area.

California↗

USGS2025

Detection of viral, bacterial, and protozoan pathogens and microbial source tracking markers in paired large- and small-volume water samples

When sampling for waterborne microbes, researchers may need to diverge from recommended sample volumes due to logistical constraints, novel targets, or challenging matrices, with little guidance about the potential impact on results. In field studies, we measured bacteria, viruses, and protozoa (15 quantitative polymerase chain reaction assays) in paired large- and small-volume samples to evaluate method performance and relevant factors. Concordance between methods was low. Large-volume ultrafiltration yielded more detections than small-volume sampling, especially for pathogens in groundwater. Greater microbial concentrations were associated with more frequent detections in small-volume samples and greater concordance between paired samples. Large-volume samples appeared to be more susceptible to diminished sensitivity from complex sample matrices. In laboratory studies, recovery of microbes was poorer for large- than small-volume methods, although large-volume methods more reliably detected low-concentration targets. Large-volume samples were less stable than small-volume samples during storage. Overall, large-volume sampling was superior for detecting pathogens but may underestimate concentrations; small-volume sampling was more prone to false negatives but was adequate when concentrations were relatively high, like we observed for microbial source tracking in surface waters.

Wisconsin↗

USGS2025

Generalized Bancroft algorithm for locating earthquakes with P- and S-wave arrival times

Because of similarities between locating an earthquake with seismic stations and locating a Global Positioning System (GPS) receiver from satellites, the Bancroft algorithm developed for GPS processing can be used to locate earthquakes. Such an approach to earthquake location differs from the conventional method of choosing an initial or trial solution and then iteratively improving the solution until convergence. The Bancroft algorithm has the advantage of being a direct, noniterative solution but with the disadvantage of only being able to accommodate a homogeneous velocity model. An additional limitation of the standard Bancroft algorithm is that it considers arrival times in a medium with a single propagation velocity. This poses no problem for GPS processing because electromagnetic waves travel at the speed of light; however, for seismic waves it means the algorithm can be applied to collections of either P ‐ or S ‐wave arrival times. Here, I show how the Bancroft algorithm can be generalized to handle both P ‐ and S ‐wave arrival‐time measurements simultaneously. I also show how to accommodate depth‐varying P ‐ and S ‐wave velocity models. I apply the generalized Bancroft algorithm to microearthquakes beneath Tanaga Volcano in Alaska and compare standard locations from the widely used HYPOINVERSE location code to Bancroft locations and to the output of HYPOINVERSE when setting the trial location to the Bancroft location. I find the Bancroft locations outperform the results from the other methods for shallow earthquakes near sea level, where a quantity known as the geometric dilution of precision is large and linearized approaches such as HYPOINVERSE are expected to struggle.

Alaska↗

USGS2024

Quality of groundwater used for domestic supply in the eastern Sacramento Valley and adjacent foothills, California

Summary More than 2 million Californians rely on groundwater from privately owned domestic wells for drinking-water supply. This report summarizes a water-quality survey of domestic and small-system drinking-water supply wells in the eastern Sacramento Valley and adjacent foothills where more than 25,000 residents are estimated to use privately owned domestic wells. Study results show that inorganic and organic constituents in groundwater were present above regulatory (maximum contaminant level, MCL) benchmarks for public drinking-water quality in 8 and 3 percent, respectively, of the aquifer area used for domestic drinking-water supply (herein, “domestic groundwater resources”; fig. 1). The only inorganic constituent detected above regulatory benchmarks was arsenic. The only organic constituent exceeding regulatory benchmarks was the fumigant 1,2,3-trichloropropane (1,2,3-TCP). Three additional organic constituents—the disinfection by-product chloroform, the gasoline oxygenate methyl tert -butyl ether (MTBE), and the solvent tetrachloroethene (PCE)—were detected at low concentrations below one-tenth of regulatory benchmarks in 34, 10, and 10 percent of domestic groundwater resources, respectively. Total dissolved solids (TDS), iron, and manganese exceeded non-regulatory aesthetic guidelines for drinking water in 5, 10, and 26 percent of domestic groundwater resources, respectively. Per- and polyfluoroalkyl substances (PFASs) were detected in 29 percent of domestic groundwater resources,with 5 percent exceeding the recently enacted (April 2024) U.S. Environmental Protection Agency MCLs. Total coliform and enterococci bacteria were detected in 13 and 8 percent of domestic groundwater resources, respectively. Redox sensitive constituents in this study included arsenic, manganese, nitrate, and iron. In the lower elevation portions of the eastern Sacramento Valley study area, reducing conditions in groundwater aquifers promote elevated arsenic, iron, and manganese, and conversely lower concentrations of nitrate. The presence of the volatile organic compound (VOC) 1,2,3-TCP was related to its past history in select agricultural land uses (on orchards or vineyards) in the Sacramento Valley; however, unlike in the San Joaquin Valley where orchards and vineyards are more common, its detection frequency was low (only detected in one well in this study). Chloroform was frequently detected in this study at low levels. Chloroform is a disinfection byproduct commonly found in domestic wells treated by shock chlorination. The solvent PCE is among the most frequently detected VOCs in groundwater, which is primarily related to its long history of use and its persistence in groundwater in oxic conditions. The gasoline oxygenate MTBE was a contaminant introduced to groundwater through atmospheric exchange when it was used as a fuel additive to decrease smog inducing emissions from vehicles. Its occurrence in groundwater at low levels is expected and makes it a potentially useful tracer of relatively recent recharge water being withdrawn from wells. The PFASs are anthropogenic chemicals with hundreds of uses, and they have been incorporated into many different products, processes, and applications worldwide. Like MTBE, the occurrence of PFASs in groundwater may be in part due to atmospheric exchange, but there are several other pathways that contribute PFASs to the environment.

California↗