Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Data Science in Science”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,642 records · Page 51Linked to original sources
USGS2025

Assimilation of reduced carbon triggers platinum alloy saturation in mafic and ultramafic magmas

It is generally observed that magmatic sulfide ores have higher ratios of Pd/Pt than the mantle-like values of their parental magmas. This discrepancy has defied simple explanation because the partitioning behavior of both elements between sulfide and silicate liquids is very similar. Assimilation of sulfur- and carbon-rich country rocks by mafic and ultramafic magmas is considered a critical, if not essential, step in the formation of magmatic base metal sulfide deposits. Although there is general consensus that the assimilation of external sulfur and carbon promotes sulfide saturation, the effect of carbon assimilation on the solubilities of platinum-group elements in natural S-bearing silicate melt has been overlooked. In this study, we investigate the variations of platinum and palladium solubilities during assimilation of graphite and methane through thermodynamic modeling, in comparison with data from an array of highly distinctive magmatic sulfide ore systems representing ages from Archean to Paleozoic, melt compositions from komatiite to basalt, and magmatic settings including lavas, hypabyssal intrusions, plutonic continental arc roots, and plutonic layered intrusions, namely: Raglan, Norilsk-Talnakh, Lac des Iles, and the J-M Reef of the Stillwater Complex. We model assimilation-fractional crystallization processes to estimate the reduction of oxygen fugacity ( ⁠fO2⁠ ) of the melt due to incorporation of graphite and methane. The simulations show that although Pd remains highly soluble during the progressive assimilation of reduced carbon, Pt solubility decreases significantly as the silicate melt becomes increasingly reduced. With less than 8 % of sediment assimilation, Pt alloy may saturate and then deviate from sulfide-undersaturated silicate melts, concomitantly increasing the Pd/Pt value of the remaining melts of the Raglan and Norilsk-Talnakh systems. For the Lac des Iles and Stillwater systems, a higher extent of assimilation is needed to reach Pt saturation because of the relatively carbon-poor nature of the lower crustal rocks. The assimilation of methane volatiles is shown to be more effective than graphite assimilation, and it provides a pathway to Pt alloy fractionation in the absence of detectable amounts of bulk host-rock assimilation. High Pd/Pt values have been documented in many world-class magmatic sulfide deposits whose parental magmas have demonstrably experienced crustal contamination. Our model suggests that although anomalous Pd/Pt values may be explained by other mechanisms such as incongruent melting of preexisting sulfide or differences in the diffusivities of the metals within achieving equilibration, the assimilation of graphite or methane may play an important role in the global occurrence of magmatic sulfide ores with elevated Pd/Pt values.

Economic Geology↗
USGS2024

Status and understanding of groundwater quality in the Mojave Basin Domestic-Supply Aquifer study unit, 2018—California GAMA Priority Basin Project

Groundwater quality in the western part of the Mojave Desert in San Bernardino County, California, was investigated in 2018 as part of the California State Water Resources Control Board Groundwater Ambient Monitoring and Assessment Program Priority Basin Project. The Mojave Basin Domestic-Supply Aquifer study unit (MOBS) region was divided into two study areas—floodplain and regional—to assess differences between the two major aquifers used for drinking water supply in the area. This assessment characterized the quality of ambient groundwater and not the quality of treated drinking water. The study included three components: (1) a status assessment, which characterized the quality of groundwater resources used for domestic drinking-water supply in the floodplain and regional study areas; (2) a brief understanding assessment, which evaluated factors that could potentially affect the quality of groundwater used by domestic wells in the region; and (3) a comparative assessment between the groundwater resources used by domestic wells and public-supply wells in the two study areas. The domestic-well assessment was based on data collected by the U.S. Geological Survey from 48 domestic wells in January–May 2018. The public-supply assessment was based on data for samples from 322 public-supply wells in 2008–18, either collected by the U.S. Geological Survey or compiled from the California State Water Resources Control Boards Division of Drinking Water publicly available database. Concentrations of water-quality constituents in ambient groundwater were compared to regulatory and non-regulatory benchmarks typically used by the State of California and Federal agencies as health-based or aesthetic standards for public drinking water. Relative concentrations, defined as the measured concentration divided by the benchmark concentration, were classified as high (greater than 1.0), moderate (greater than 0.5 for inorganic constituents or 0.1 for organic and special-interest constituents, and not high), or low (concentrations lower than moderate). The floodplain and regional study areas were divided into 15 and 35 grid cells, respectively, and grid-based methods were used to compute the areal proportions of the two study areas with high, moderate, or low relative concentrations of individual constituents and classes of constituents. For the domestic-supply assessment, one or more inorganic constituents with health-based benchmarks were detected at high relative concentrations in 58 percent of the regional study area and 13 percent of the floodplain study area. The inorganic constituents with health-based benchmarks detected at high relative concentrations in the regional study area were arsenic, chromium and hexavalent chromium, fluoride, adjusted gross alpha particle activity, uranium, molybdenum, strontium, and nitrate; only arsenic was detected at high relative concentrations in the floodplain study area. One or more inorganic constituents with secondary maximum contaminant level benchmarks were detected at high concentrations in 15 and 6.7 percent of the regional and floodplain study areas, respectively. The constituents detected at high relative concentrations in the regional study area were total dissolved solids, chloride, sulfate, and iron; only total dissolved solids and sulfate were detected at high relative concentrations in the floodplain study area. Organic constituents were not detected at moderate or high relative concentrations in either the regional or floodplain study areas. Volatile organic compounds were detected at low relative concentrations in 21 and 27 percent of the regional and floodplain study areas, respectively, and pesticides were detected at low relative concentrations in 9.1 and 20 percent of the regional and floodplain study areas, respectively. The only individual organic constituent detected in more than 10 percent of either study area was the trihalomethane trichloromethane. Total coliform bacteria were detected in 15 and 27 percent of the grid wells in the regional and floodplain study areas, respectively. The greater prevalence of high relative concentrations of many inorganic constituents in the regional study area compared to the floodplain area likely indicates the greater diversity of geologic material at depth in aquifer material and generally finer-grained alluvium compared to the floodplain study area combined with generally older groundwater that has had more contact time with aquifer materials. In general, trace element concentrations (1) increased with increasing groundwater age, (2) increased with distance from recharge sources in the mountains, and (3) increased with closer proximity to some types of geological units. In general, groundwater from domestic wells in the floodplain study area is young, with most samples containing a component of modern groundwater based on tritium and unadjusted carbon-14 activities, whereas groundwater from domestic wells in the regional study area generally is old, with most samples having unadjusted carbon-14 ages of 5,000–40,000 years. Public-supply wells in MOBS generally were deeper than domestic wells and presumably are in contact with older, more weathered alluvium that may have more mobile trace elements, such as arsenic or uranium. However, only 26 percent of the public-supply regional study area had high relative concentrations of inorganic constituents, compared to 58 percent for the domestic regional study area. The percentages of the public-supply and domestic floodplain study areas with high relative concentrations of inorganic constituents were 11 and 13 percent, respectively. The ages of groundwater used by public-supply and domestic wells in each study area were similar, which was not expected given the greater depth of the public-supply wells. Three potential factors may contribute to these results: (1) greater spatial footprint of domestic well network, which may result in domestic wells pumping groundwater from fractured bedrock or mineralized areas not used by public-supply wells; (2) greater pumping rates in public-supply wells, resulting in more water being withdrawn from coarse-grained, heterogeneous alluvium than finer-grained layers, which may have higher concentrations of (or more mobile) inorganic constituents; and (3) a greater degree of well management with public-supply wells, which may include pausing use of or decommissioning wells if treating or blending water is not feasible to lower constituent concentrations.

California↗
USGS2026

Unraveling protracted modification of Archean and Paleoproterozoic crust in central Laurentia, Penokean orogen, with garnet and accessory mineral geochronology and microstructural analysis

Proterozoic metamorphism and deformation of the southern margin of the Superior craton in the Lake Superior region is attributed to the Penokean orogeny (1890−1830 Ma). This model includes a period of crustal inversion in which Archean basement blocks were exhumed through overlying Paleoproterozoic strata, producing the corridor of gneiss domes that parallels the trend of the Penokean orogen across the northern Midcontinent, USA. However, recent geologic mapping and 40 Ar/ 39 Ar geochronology challenge this interpretation, suggesting instead that the gneiss dome structures reflect younger episodes of tectonic activity along the southern margin of Laurentia. In absence of integrated pressure-temperature-time-deformation constraints for these rocks, interpretations are largely limited to their final cooling history, making it difficult to both identify the tectonic forces that shaped the architecture of the Penokean orogenic belt and assess the extent to which later Proterozoic tectonism modified the southern Superior craton. We address this problem with an approach joining thermodynamic modeling, garnet and accessory mineral geochronology, and microstructural analysis for several metamorphic rocks across the gneiss dome corridor. The U-Pb ages of titanite reveal that the Proterozoic geometries of exhumed basement gneiss domes are governed by preexisting Archean structures. Garnet Lu-Hf geochronology constrains the timing of prograde-to-peak metamorphism in the Penokean orogenic belt. Granulite facies metamorphism is related to the final stages of the Penokean orogeny at 1837 Ma and localized in a belt of high-grade rocks near a major Penokean suture. Garnet Lu-Hf ages of samples adjacent to gneiss domes reflect regional metamorphism following the accretionary phase of the Penokean orogeny, between 1825 Ma and 1782 Ma, which we suggest reflects continued crustal thickening related to convergence farther south during this time interval. Combination of garnet microstructures and Sm-Nd ages reflects later exhumation of gneiss domes and buried metasedimentary rocks by ca. 1750 Ma, consistent with previously published 40 Ar/ 39 Ar cooling ages across the region. Reset Lu-Hf and Sm-Nd garnet ages and U-Pb ages of syn-kinematic titanite reflect reactivation of primary Penokean structures during this period of basement uplift. These data document significant modification of the Penokean orogen and the Archean crust of the southern Superior province between 1800 Ma and 1700 Ma. Tectonic activity during this interval coincides with collisional events recognized in western Laurentia, suggesting that the period immediately following the Penokean orogeny may be a broadly important time for crustal growth and modification in proto-North America.

Michigan, Wisconsin↗
USGS2025

ShakeAlert® version 3: Expected performance in large earthquakes

The ShakeAlert earthquake early warning (EEW) system partners along with U.S. Geological Survey (USGS) licensed operators deliver EEW alerts to the public and trigger automated systems when a significant earthquake is expected to impact California, Oregon, or Washington. ShakeAlert’s primary goal is to provide usable warning times before the arrival of damaging shaking. EEW is most likely to achieve this goal in large‐magnitude earthquakes. In recent years, ShakeAlert has gone through a series of upgrades to its underlying scientific algorithms aimed at improved performance during large earthquakes. Version 3 of this software recently went live in the production system and includes improvements to all algorithms. The main seismic algorithms that detect an earthquake and characterize its location, magnitude, and fault rupture orientation are faster than older versions. Other key changes include: using real‐time geodetic data to characterize the magnitude growth in large earthquakes; the introduction of an alert pause procedure to compromise between speed near the epicenter and improved accuracy at larger distances; and the inclusion of a nonergodic site‐response model in the ground‐motion predictions. ShakeAlert has achieved its primary goal of usable warning times before strong shaking at some locations in real‐time operations in recent M 6 earthquakes. Using offline tests, we demonstrate usable warning times are possible for many sites with peak shaking values of modified Mercalli intensity (MMI) 7–8 in M 7+ earthquakes and also for many MMI 8–9 sites in M 8+ earthquakes. ShakeAlert partners use a variety of MMI and magnitude thresholds in deciding when to alert their users within bounds set by the USGS. Our study shows that there is room to raise the magnitude thresholds up to about M 5.5 without adversely affecting performance in large earthquakes. The ground‐motion criteria are more complex owing to a significant drop‐off in warning times between the MMI 4 and 5 levels of predicted shaking. However, widely used ShakeAlert products, such as the MMI 3 and 4 contour products, can provide sufficiently long warning times before strong shaking in moderate‐to‐great earthquakes to enable a range of protective actions.

Bulletin of the Seismological Society of America↗
USGS2026

Small-volume tephra deposits of the May 1924 explosions from Halemaʻumaʻu, Kīlauea volcano, and their origin

More than 50 explosive eruptions occurred from Halemaʻumaʻu at Kīlauea volcano over 17 days from May 11 to 27, 1924. Ballistics weighing as much as 14,000 kg were ejected and most landed within 2 km of the vent. Fine ash made up a major component of the tephra and was dispersed tens of kilometers downwind. Draining of the Halemaʻumaʻu lava lake occurred in late February 1924, with the crater floor eventually subsiding by a further ∼70 m (to ∼180 m below the crater rim) by the time the first explosions took place during the night of May 10–11. The largest explosions occurred on May 17–18 and smaller explosions continued until May 27, at which point Halemaʻumaʻu had more than doubled in width and depth. The explosions generated plumes reaching up to ∼10 km high with ballistics ejected up to 2 km from the crater. Almost 100 years later, we investigate and characterize the preserved tephra deposits within ∼3 km of the 1924 crater rim. Grain size and shape analyses were performed on 202 samples collected from 34 tephra profiles using dynamic image analysis, with a subset of layers from nine tephra profiles used for componentry (200 grains per layer in the 0.5–1 mm size fraction). Additionally, we characterize the average diameters (using the five largest clasts) at 216 locations and measure the average diameters of 2291 ballistics (largest per ∼100 m 2 area). Physical descriptions from fieldwork and grain size distributions were used to subdivide the tephra layers into five lithofacies: coarse homogeneous, fine homogenous, red ash, accretionary lapilli-bearing, and finely laminated. Grain size versus shape data show a range of values that demonstrate most grains are dense, smooth, and equant, in alignment with lithic clasts dominating the tephra componentry. The fine grained and accretionary lapilli-bearing nature of some of these lithofacies confirms that water influenced the style of the explosions. However, we also note juvenile clasts within many of the tephra layers, indicating that many of the layers were formed during phreatomagmatic explosions (sensu stricto), despite the eruptive mechanism being dominantly phreatic. Juvenile clasts are more abundant higher in the tephra profiles, suggesting that juvenile magma was more involved later in the explosive sequence. Thermal and hydrologic modeling indicate that groundwater inflow into a short-lived, small-diameter volcanic conduit (10-m to 120-m-diameter used for modeling) during the 78–85 days preceding the first explosion provides a physically plausible mechanism for this eruptive sequence.

Hawaii↗
USGS1999

Water quality of Rob Roy Reservoir and Lake Owen, Albany County, and Granite Springs and Crystal Lake Reservoirs, Laramie County, Wyoming, 1997-98

The water quality of four reservoirs was assessed during 1997 and 1998 as a cooperative project between the Cheyenne Board of Public Utilities and the U. S. Geological Survey. The four reservoirs, Rob Roy, Lake Owen, Granite Springs, and Crystal Lake, provide approximately 75 percent of the public water supply for Cheyenne, Wyoming. Samples of water and bottom sediment were collected and analyzed for selected physical, chemical, and biological characteristics to provide data about the reservoirs. Water flows between the reservoirs through a series of pipelines and stream channels. The reservoirs differ in physical characteristics such as elevation, volume, and depth. Profiles of temperature, dissolved oxygen, specific conductance, and pH were examined. Three of the four reservoirs exhibited stratification during the summer. The profiles indicate that stratification develops in all reservoirs except Lake Owen. Stratification developed in Rob Roy, Granite Springs, and Crystal Lake Reservoirs by mid-July in 1998 and continued until September, with the thickness of the epilimnion increasing during that time. Secchi disk readings indicated Rob Roy Reservoir had the clearest water of the four reservoirs studied. The composition of the phytoplankton community was different in the upper two reservoirs from that in the lower two reservoirs. Many of the species found in Rob Roy Reservoir and Lake Owen are associated with oligotrophic, nutrient-poor conditions. In contrast, many of the species found in Granite Springs and Crystal Lake Reservoirs are associated with mesotrophic or eutrophic conditions. The total number of taxa identified also increased downstream. The chemical water type in the reservoirs was similar, but dissolved-solids concentrations were greater in the downstream reservoirs. Water in all four reservoirs was a calcium-bicarbonate type. In the fall of 1997, Rob Roy Reservoir had the lowest dissolved-solids concentration (19 milligrams per liter), whereas Crystal Lake Reservoir had the highest concentration (63 milligrams per liter). Relatively little differences in the concentrations of major-ion species were noted between samples collected near the surface and near the bottom of the same reservoir. In contrast, iron and manganese concentrations generally were higher in samples collected near the bottom of a reservoir than in near-surface samples collected from the same reservoir. Composite bottom-sediment samples from all four reservoirs contained similar concentrations of bulk constituents such as aluminum, iron, phosphorus and titanium, but varied in concentrations of trace elements. Trace-element concentrations in Rob Roy Reservoir and Lake Owen were similar to the crustal average, whereas in Granite Springs and Crystal Lake Reservoirs the concentrations were similar to granitic rocks.

Wyoming↗
USGS2025

Groundwater hydrology, groundwater and surface-water interactions, water quality, and groundwater-flow simulations for the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado, 2017–19

In 2017, the U.S. Geological Survey, in cooperation with the Upper Arkansas Water Conservancy District, began a study to provide a comprehensive analysis of the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado. The study included collection of data pertaining to groundwater hydrology, groundwater and surface-water interactions, and water quality in the alluvial aquifer. In addition to providing foundational information on the hydrology of the alluvial aquifer, a numerical groundwater-flow model was developed to estimate the potential effects of additional storage of groundwater in the alluvial aquifer. Groundwater-level elevation data from 30 wells were used to estimate groundwater-flow directions in the alluvial aquifer, which were generally from the southwest to northeast, away from the Sangre de Cristo Mountains and towards perennial streams in the center of the valley. Although some seasonal variation was apparent in groundwater-level elevation records, no statistically significant seasonal trends were indicated. Statistically significant long-term trends were indicated in groundwater-level elevation records for 8 of the 30 wells, and of these wells with statistically significant trends, all but 1 indicated a negative trend of groundwater-level elevations. Spatial evaluation of wells with statistically significant negative groundwater-level elevation trends showed many are in areas of denser well drilling for domestic or other uses, indicating increasing groundwater use could potentially be causing groundwater-level elevation declines. There were instances of wells with no statistically significant groundwater-level elevation trends also located in areas of greater density of well completions. Additional investigations may be necessary to more fully characterize the processes responsible for negative groundwater-level elevation trends. Streamflow gain or loss calculations were completed for low flow in 2017–19 and for high flow in 2018 in nine reaches of streams within the study area. Stream reaches of the upper Texas Creek, upper Grape Creek, upper-middle Grape Creek, and Taylor Creek displayed consistent streamflow loss in each period from 2017 to 2019. These stream reaches represent long-term sources of recharge to the alluvial aquifer. Streamflow gain or loss varies through time in other stream reaches (lower Texas Creek, lower-middle Grape Creek, lower Grape Creek below Westcliffe, and lower Grape Creek above DeWeese Reservoir). The temporally variable behavior indicates these stream reaches may be sources of groundwater recharge or areas of groundwater discharge, likely depending on temporal dynamics between the elevation of the water table and the stream. Water-quality samples were collected from 10 groundwater wells and 10 stream sites during September through November 2019. All groundwater and stream samples were analyzed for major and trace elements and stable isotopes of water. A subset of groundwater samples was also analyzed for the environmental tracers sulfur hexafluoride, tritium, and noble gases. Comparison of water-quality results to U.S. Environmental Protection Agency drinking water-quality standards indicated no constituents exceeded primary standards for human health. Spatial evaluation of water quality indicated the concentrations of various constituents are likely controlled by groundwater and surface-water interactions and by spatial variability in bedrock geology underlying the alluvial aquifer. Specifically, streams shown to gain from groundwater had water chemistry constituent compositions similar to groundwater, whereas streams exiting the Sangre de Cristo Mountains tended to have compositions consistent with snowmelt. Groundwater geochemistry appeared to be partially controlled by oxidation-reduction processes and by proximity to igneous rocks in the Wet Mountains. Environmental tracers used to estimate groundwater age indicated all sampled groundwater contained tracers representing modern recharge (approximately less than 65 years old) but mixing of premodern recharge (approximately more than 65 years old) also occurs. Spatial evaluation of environmental tracers indicated large faults may be conduits for upwelling of older groundwater. No trends were observed in groundwater age with well depth, indicating all sampled wells are located within the zone of active groundwater flow. The presence of modern groundwater in wells with statistically significant negative groundwater-level elevation trends indicates groundwater storage depletions may be partially offset by capture of modern recharge. Repeated sampling of groundwater age would be necessary, however, to determine if any trends in groundwater age exist, which may indicate changing groundwater recharge, storage, or discharge. Additional investigations could also consider quantifying groundwater age in deeper wells to more fully define the depth of active groundwater flow. A numerical groundwater-flow model was developed to estimate components of the water budget, simulate groundwater and surface-water interactions, and evaluate the potential effects of aquifer storage and recovery. Simulated groundwater-level elevations from the calibrated groundwater-flow model are similar to the observed pattern of groundwater-level elevations with higher elevations in the western part of the study area along the Sangre de Cristo Mountains. Simulated water-budget components indicate most of the recharge to the alluvial aquifer is derived from streamflow losses, which is consistent with observations of losing streams along the mountain front. The largest groundwater discharge component of the alluvial aquifer was to streams in the center of the valley, where observations of stream gain or loss indicated the predominance of gaining conditions. Comparison of groundwater and surface-water interactions between the calibrated groundwater-flow model for 2000-19 (the base-case model) and a simulation including additional recharge, representing potential aquifer storage and recovery operations, indicated the additional recharge distributed throughout the area had minimal effects on streamflow in the nearby Grape Creek. An analysis of subregional groundwater budgets showed approximately 54 percent of the additional recharge flowed back to nearby Grape Creek, and the other 46 percent was distributed laterally into adjacent cells in the alluvial aquifer. The comparison of simulations and subregional water budget show the additional recharge did not substantially alter groundwater-level elevations or basin wide groundwater storage. Although the analysis of additional recharge provided in the numerical groundwater-flow model considers only one of many possible recharge scenarios, the model provides a useful tool that could be modified for various scenarios to understand potential effects of managed aquifer recharge.

Colorado↗
USGS2024

Using the horizontal-to-vertical spectral ratio method to estimate thickness of the Barry Arm landslide, Prince William Sound, Alaska

Conducting detailed investigations of large landslides is difficult, especially in the subsurface, largely due to environmental factors such as steep slopes, difficult access, and numerous objective hazards. These factors have made it challenging to accurately estimate the depth to the failure surface of the Barry Arm landslide, a large (roughly 10 8 cubic meters), deep-seated bedrock landslide in Prince William Sound, Alaska, recognized in 2019. The landslide has exhibited accelerated movement in recent years and poses a potential tsunamigenic hazard if rapid failure occurs. Failure surface depth, equivalent to landslide thickness, is a necessary metric for landslide-volume calculations and associated tsunami wave models. In this report, we used seismic noise recorded by a seismometer located on the Barry Arm landslide in Alaska to calculate the horizontal-to-vertical spectral ratio (HVSR) to investigate the site fundamental frequency ( f 0 ) and depth of the failure surface. To ensure that observed peak frequencies in the spectral ratio were related to the underlying stratigraphy (and not caused by other noise sources like nearby glaciers, topographic resonance, weather, or human activities), we also calculated HVSRs using earthquake signals, HVSRs at other seismic stations within a 2.5-kilometer radius, and a standard spectral ratio between the landslide station and other sites. We observed multiple peaks in the landslide HVSR curves at 1.5 hertz (Hz), 4–5 Hz, and 7–11 Hz. The frequencies of these peaks were consistent at the landslide site through time and across methods and were dissimilar to those identified at other seismic stations in the area, making it unlikely the peaks were caused by local noise. Directional HVSRs calculated at 15-degree intervals showed amplification of the higher frequency peaks in the direction parallel to slip, indicating two-dimensional site effects. We used the distinct frequency peaks in the seismic record to develop a 4-layer conceptual model of the landslide wherein the top of the deepest layer represents the primary failure surface, or the boundary between damaged (mobile) and undamaged material. We inverted Rayleigh wave ellipticity curves within this 4-layer configuration with constraints on S-wave velocity and layer thickness based on analogous material properties identified in the literature. This was necessary absent any site-specific subsurface S-wave velocity data. The best-fitting models indicate a mean slope-normal depth to the failure surface of 188 (±9) meters (m), with additional stratigraphic boundaries at 4 and 20 m below ground surface, potentially representing layered motion. These results agree with and improve upon ranges estimated by previous studies and can support future modeling and assessment efforts at Barry Arm.

Alaska↗
USGS2025

Flood-Inundation Maps of the Current and Jacks Fork Rivers including the Ozark National Scenic Riverways, Southeast Missouri, 2023

Digital flood-inundation maps for a 131.8-mile reach of the Current River and a 44.6-mile reach of the Jacks Fork River, in southeast Missouri, were created by the U.S. Geological Survey (USGS) in cooperation with the Ozark Foothills Regional Planning Commission and the South Central Ozark Council of Governments. The maps also encompass the 134 miles of the Current and Jacks Fork Rivers within the Ozark National Scenic Riverways, which is the first national park area to protect a river system. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Program website at https://water.usgs.gov/osw/flood_inundation/ , depict estimates of the areal extent and depth of flooding corresponding to selected water levels (hereafter referred to as “stages”) at eight reference USGS streamgages—five on the Current River (USGS station numbers 07064440, 07064533, 07066510, 07067000, and 07068000) and three on the Jacks Fork River (USGS station numbers 07065200, 07065495, and 07066000). Near-real-time stages at these streamgages may be obtained from the USGS National Water Information System at https://doi.org/10.5066/F7P55KJN or the National Weather Service National Water Prediction Service at http://water.noaa.gov/ , which also forecasts flood hydrographs at four of these sites (USGS station numbers 07067000, 07068000, 07065495, and 07066000). Flood profiles were computed for seven of the eight map reaches by means of two-dimensional hydraulic models and the remaining reach by a one-dimensional hydraulic model. The models were calibrated by using stage-streamflow relations or streamflow measurements at the USGS streamgages and from high-flow stage measurements from water-level loggers distributed throughout the reaches. The hydraulic models were used to compute water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datums. The profile stages ranged from the National Weather Service “action stage” or near bankfull, to a stage exceeding the highest recorded water level at each streamgage. The simulated water-surface profiles were then combined with a digital elevation model (derived from light detection and ranging data having a nonvegetated vertical accuracy of a maximum 10-centimeter root mean square error) to delineate the area flooded at each water level and the associated water depths. The availability of these maps, along with information regarding current stage from the USGS streamgage and forecasted high-flow stages from the National Weather Service, will provide emergency management personnel, resource managers, and residents with information that is critical for flood-response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Missouri↗
USGS2026

Treatability study to evaluate bioremediation of trichloroethene at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, 2020–22

Executive Summary Chlorinated solvents, including trichloroethene (TCE) and other chlorinated volatile organic compounds (cVOCs), are widespread contaminants that can be treated by bioremediation approaches that enhance anaerobic reductive dechlorination. Reductive dechlorination can be enhanced either through the addition of an electron donor (biostimulation) or the addition of a known dechlorinating culture (bioaugmentation) along with an electron donor. Although bioremediation has been applied at many TCE-contaminated groundwater sites, application in source zones at sites where residual dense nonaqueous phase liquid (DNAPL) is present is more limited. In this study, laboratory and field treatability tests were completed to evaluate the potential application of anaerobic bioremediation for a shallow groundwater plume containing TCE in a perched alluvial aquifer at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, which was on the National Priorities List as the New Brighton/Arden Hills Superfund site until 2019. In addition to the presence of residual DNAPL at the site, temporal variability in groundwater flow directions and input of oxygenated recharge were possible complicating factors for the application of enhanced anaerobic biodegradation in the shallow plume. The Site K plume extends beneath the footprint of Building 103, which was demolished in 2006, and soil excavations to a maximum depth of 6 feet (ft) below ground surface in 2014 were known to leave some deeper contaminated soil in place in the TCE source area. Groundwater treatment at the site, formalized as part of the 1997 Record of Decision, has been in operation since 1986 and consists of an extraction trench at the downgradient edge of the plume to collect groundwater, which is then pumped to an on-site air stripper. Groundwater concentrations in the plume have been relatively stable since treatment began, indicating a continued source of TCE in the aquifer. The desire for a destructive remedy that would enhance the removal of cVOCs in the aquifer at Site K and shorten the remediation timeframe led the U.S. Army to request that the U.S. Geological Survey conduct a groundwater treatability study to assess bioremediation. This report describes the U.S. Geological Survey bioremediation treatability study conducted during 2020–22, including pre-design site characterization to assist in formulating the bioremediation approach, laboratory experiments to support the design of the field pilot test, and implementation and 1-year performance monitoring results for the pilot test. Pre-design site characterization included the collection of soil cores for cVOC analysis and lithologic descriptions and the re-installment of three wells to obtain hydrologic measurements and initial groundwater chemistry. Relatively flat head gradients were measured at the site, and substantial decreases in water-level elevations occurred from spring to summer (May–July 2021). Continuous water-level monitoring indicated a rapid response to precipitation. Groundwater flow velocities were consistently less than 0.5 foot per day, and the pilot bioremediation test was therefore designed with short lateral distances (about 5 ft) between injection and individual monitoring points. Soil analyses confirmed that high volatile organic compound contamination was left in place in the source area. The highest concentrations were near or in clay at the base of the perched aquifer. Concentrations of cVOCs measured in the replaced wells were consistent with historical data and had a maximum TCE concentration of 57,700 micrograms per liter (μg/L), indicative of nearby residual DNAPL based on the general rule of observed concentrations exceeding 1 percent of solubility. The primary TCE daughter product detected was 1,2-cis-dichloroethene (cisDCE), which indicated limited reductive dechlorination in the plume. Groundwater in both the source and downgradient areas was relatively reducing during the pre-design characterization, particularly in the source area where methane concentrations greater than 400 μg/L were measured. Initial laboratory tests conducted using native aquifer microorganisms from the three replacement wells showed that anaerobic TCE biodegradation rates were low when biostimulated with the addition of sodium lactate as an electron donor, also known as a carbon donor, and resulted in the production of only cisDCE. Addition of a known dechlorinating culture, WBC-2, however, resulted in rapid biodegradation and production of ethene, verifying complete reductive dechlorination of TCE. Microcosms constructed with aquifer soil collected from the site were used to evaluate other electron donors besides lactate to support reductive dechlorination by WBC-2, including corn syrup as an alternative fast-release compound and whey, soy-based vegetable oil, and 3-D Microemulsion (Regenesis, San Clemente, California) as slow-release compounds. First-order rate constants for total organic chlorine removal in these WBC-2 amended microcosms were greatest with either lactate or vegetable oil as the donor, ranging between 0.061 and 0.047 per day or corresponding half-lives of 11–15 days. Testing of commercial products in other WBC-2-bioaugmented microcosms led to selection for the field pilot test of an emulsified vegetable oil product that also contained some sodium lactate as a fast-release donor. Delaying the addition of WBC-2 relative to the donor in the microcosms resulted in the most rapid overall biodegradation rates. The selected design for the pilot test utilized three separate test plots, each about 30-ft wide and 60-ft long: plots GS1 and GS2 in the source area of the plume and plot GS3 in the downgradient area of the plume near the excavation trench. Each test plot had one injection well, one monitoring well upgradient from the injection point, and 12 surrounding monitoring wells in a grid to capture variable groundwater flow directions. Donor injections, which included a bromide tracer, were completed in October 2021, immediately following baseline sampling, and the WBC-2 culture was injected about 40 days later, between November 30 and December 2, 2021. Performance monitoring conducted until December 2022 included hydrologic measurements and analyses of cVOCs, redox-sensitive constituents, dissolved organic carbon, bromide, volatile fatty acids, compound-specific carbon isotopes, and microbial communities. The biogeochemical data collected during the pilot tests in the three treatment plots showed that enhanced, complete reductive dechlorination of cVOCs in the groundwater was achieved in the GS1 and GS3 plots. In contrast, evidence of distribution of the injected amendments and subsequent biodegradation was limited in GS2, which was in an area of more heterogeneous soil lithology and low water table elevations. The molar composition of volatile organic compounds in the GS1 and GS3 plots was dominated by ethene in wells that were reached by the injected amendments by the end of the monitoring period. In the GS1 and GS3 plots, similar patterns were observed of cVOC concentrations decreasing to near detection levels, or below, at some wells sampled in July and October 2022, whereas ethene became dominant and indicated sustained complete reductive dechlorination. Baseline cVOC concentrations were more than a factor of 10 higher in the groundwater in the GS1 plot than in GS3, but no apparent inhibition of complete dechlorination occurred. As expected from the initial pre-design site data and the laboratory experiments, enhanced dissolution of residual DNAPL coupled to biodegradation was evident in the GS1 plot, where a marked increase in dichloroethene (DCE) above the initial baseline and upgradient TCE and DCE concentrations occurred. DCE concentrations subsequently declined where DNAPL dissolution was evident, concurrent with production of vinyl chloride and then predominantly ethene. Thus, overall biodegradation rates outpaced the DNAPL dissolution and desorption and DCE production in the source area. This success in complete degradation to predominantly ethene was achieved even in areas where the DCE concentrations reached a maximum of about 30,000 μg/L. Compound specific isotope analysis of carbon in TCE, cisDCE, trans-1,2-dichloroethene, and vinyl chloride was conducted to provide another line of evidence of the occurrence and extent of anaerobic biodegradation. Along a flow path in each plot that was affected by the injected amendments, carbon isotopes in the TCE and daughter cVOCs in the groundwater became isotopically heavier, indicating biodegradation. Enhanced biodegradation rates calculated from the field tests in GS1 and GS3 showed half-lives of 36.9–75.3 days for DCE degradation and 9.48–38.5 days for ethene production. Notably, these ethene production rates calculated from the field tests are consistent with the results of WBC-2-bioaugmented microcosms amended with either lactate or vegetable oil, which had half-lives for total organic chlorine removal that ranged from 11 to 15 days. These rates indicated rapid enhanced biodegradation, which is promising for application of a full-scale bioremediation remedy. Ultimately, however, the mass of residual or sorbed TCE in the aquifer that remains accessible for dissolution and biodegradation would likely control the time required for a full-scale bioremediation effort to achieve performance goals for TCE and cisDCE specified in the Record of Decision for Site K. The field pilot tests showed that the relatively low hydraulic head gradients and temporal changes in groundwater flow directions in the shallow aquifer would add complexity to a full-scale bioremediation effort. The radius of influence (ROI) at GS1 and GS3 (16.3 ft and 12.7 ft, respectively) were close to the design ROI of 15 ft. The estimated ROI at GS2 was about four times the design ROI, but may be less reliable at this location owing to groundwater flow direction. In addition, the low temperatures following WBC-2 injection in late November to early December 2021, in combination with the low hydraulic head gradients, were probably major factors in the delay observed before the onset of enhanced biodegradation following injection of the culture. Additional test injections could be beneficial to optimize the timing of donor and culture injections with the variable temperatures and hydraulic head in the shallow aquifer.

Minnesota↗
USGS2025

Spatiotemporal variability of algal biomass and nitrate in Owasco and Seneca Lakes in the Finger Lakes Region, New York, in 2019

Cyanobacterial harmful algal blooms (CyanoHABs) have become increasingly common, threatening the security of water resources globally. The U.S. Geological Survey conducted high-resolution nearshore mapping surveys using boat-mounted multiparameter sondes and nitrate sensors during the summer and fall of 2019 on Owasco Lake and Seneca Lake, two lakes with documented CyanoHABs in the Finger Lakes region of New York State. Discrete sensor measurements and water-quality samples were collected at fixed points along survey routes and continuous data were generated at open-water monitoring platforms. This investigation examined whether water-quality information from nearshore surveys was representative of open-water conditions and if nearshore surveys could be used to identify areas with localized nearshore CyanoHABs and potential sources of nutrients not captured by tributary sampling. In addition to comparisons across methods, nearshore concentrations of nitrate and chlorophyll were evaluated relative to tributary outlets, cyanobacterial abundance and biovolume at discrete locations, and the locations of near-surface CyanoHABs that were designated as “confirmed with high toxins” by the New York State Department of Environmental Conservation. Nitrate and chlorophyll concentrations were comparable across methods for each lake, although concentration ranges were typically higher for nearshore mapping datasets than for nearshore discrete datasets. Nearshore surveys indicated areas of nitrate enrichment that varied temporally in both lakes. Orthophosphate was not routinely detected. Across methods, median chlorophyll concentrations were higher for the summer survey than for the fall survey in Owasco Lake. Nearshore chlorophyll concentrations varied more temporally in Owasco Lake than in Seneca Lake. Phytoplankton and cyanobacterial abundance and biovolume were about five times higher in Owasco Lake than in Seneca Lake. Cyanobacteria dominated the phytoplankton community in most samples, and Microcystis comprised the bulk of the cyanobacterial biovolume. The most abundant potential cyanotoxin-producing (specifically microcystins) genera were Microcystis , Synechococcus , Aphanocapsa , and Pseudanabaena . The cyanobacterial community composition was comparable between open-water monitoring platforms and nearshore samples. Microcystins were detected in seven survey samples from Owasco Lake, in one survey sample from Seneca Lake, and in one sample each from the open-water monitoring platforms on Owasco and Seneca Lakes that were collected about 7 days before the fall surveys. Microcystin detections were not consistently associated with high cyanobacterial cell counts or cyanotoxin-producing genera. Results from nearshore surveys were comparable to open-water monitoring platforms and discrete nearshore observations in the absence of nearshore or open-water CyanoHABs in these systems during the study. Patterns of nearshore concentrations of nitrate and chlorophyll from nearshore surveys may aid in the identification of areas with localized nitrate loading and shifts in phytoplankton abundance and community composition.

New York↗
USGS2025

Hydrogeologic framework of the Mountain Home area, southern Idaho

In the arid western Snake River Plain around the City of Mountain Home, Idaho, declining groundwater levels concern agricultural, municipal, and other water users who rely on groundwater for sustenance because surface-water resources are limited. The U.S. Geological Survey developed this hydrogeologic framework to provide an updated characterization of groundwater resources in the western Snake River Plain around the City of Mountain Home. The hydrogeologic framework comprises: (1) a conceptual description of hydrogeologic units, (2) a three-dimensional hydrogeologic model and borehole database, (3) a map of groundwater levels and change, and (4) a discussion of groundwater occurrence and movement within the study area. Hydrogeologic units were defined based on existing literature and the borehole database compiled for this study; the five hydrogeologic units are granite, rhyolite, basalt, fine-grained sediments, and coarse-grained sediments. Each unit can bear water, but the main regional aquifer in the study area occurs in the basalt and fine-grained sediment units with depth to water ranging from 150 to 765 feet. A perched groundwater zone near the City of Mountain Home is primarily hosted in basalt and used domestically with most depths to water ranging from 30 to 100 feet. Interflow zones, scoria, and vertical fractures create heterogeneity within the basalt hydrogeologic unit that exerts strong control on groundwater movement, creating horizontal perching conditions and zones of enhanced vertical conductivity that facilitate downward groundwater percolation. In the fine- and coarse-grained sediments and rhyolite units, inferred faults both impede and enhance groundwater movement. The borehole database was constructed by digitizing 540 well-driller reports and was used to build a three-dimensional hydrogeologic framework model which reasonably represents the spatial distribution of hydrogeologic units in the study area. Generally, fine-grained sediments underlie much of the study area, with basalt concentrated in the central and western study area and rhyolite and granite in the uplands to the north. Groundwater levels were measured in 180 wells in March and November 2023; these data were used to develop water-table contour maps and describe groundwater-level change over an irrigation season. Groundwater generally flows south-southwest to the Snake River and groundwater levels declined across most of the study area (from 0.03 to 22.01 feet) between spring and autumn 2023, which is consistent with long-term declines in the Cinder Cone Butte Critical Groundwater Area and Mountain Home Groundwater Management Area. Groundwater levels rose (0.6 to 15.44 feet) over the irrigation season in most wells in the perched groundwater zone near the City of Mountain Home and near the Snake River, indicating the importance of surface-water recharge to groundwater in areas where surface water irrigation occurs. In aggregate, this hydrogeologic framework provides an updated characterization of and new insights into groundwater resources in the study area to help inform water resources management.

Idaho↗
USGS2025

Assessment of channel morphology, hydraulics, and bedload transport along the Siletz River, western Oregon

Significant Findings Chinook salmon ( Oncorhynchus tshawytscha ) and Pacific lamprey ( Entosphenus tridentatus ) are native, anadromous fish species in the Siletz River Basin, western Oregon, that face many threats to their survival in freshwater and the ocean. The Confederated Tribes of Siletz Indians of Oregon seek to mitigate freshwater threats to Chinook salmon and Pacific lamprey, where possible, with habitat conservation and restoration efforts. This study was conducted to assist the Confederated Tribes of Siletz Indians of Oregon in documenting and understanding the hydrogeomorphic processes shaping present-day habitat conditions and assessing future habitat implications for Chinook salmon and Pacific lamprey along the main-stem Siletz River. As such, this study focused on understanding geomorphic processes and patterns of channel change, including lateral and vertical adjustments in channel position and changes in bed-material sediment (sands, gravels, and cobbles that mantle the channel bed), which collectively determine overall patterns of channel morphology and fluvial habitats. Objective One was to evaluate lateral changes in channel position, vertical changes in bed elevation, and longitudinal patterns in bed-material particle size along the Siletz River using detailed channel maps developed from aerial photographs collected from 1939 to 2016, long-term records of stage and discharge collected by the U.S. Geological Survey (USGS) near the City of Siletz, and sediment particle size data. Objective Two was to assess hydraulic conditions using one- and two-dimensional hydraulic models and transport capacity of bed-material sediment using bedload transport models and sediment particle size data for a range of discharge conditions. Objective Three was to identify potential burrowing habitat for lamprey larvae (PBH) along the Siletz River network and provide insights in local factors influencing PBH along the main-stem Siletz River. The overall findings are synthesized to describe habitat implications for Chinook salmon and Pacific lamprey under present-day and future conditions. Results of Objective One, an evaluation of changes in channel position and bed elevations and longitudinal patterns in bed-material particle size along the Siletz River, include the following From 1939 to 2016, channel planform and the mapped area of gravel bars did not change considerably along the 97.2-kilometers (km) of Siletz River between Elk Creek and Millport Slough, except for in short sections generally less than 1 km long. This inherent lateral channel stability results from the resistant bedrock and terraces that bound most of the channel and limit lateral changes in channel position. Intermittent sections along the study reach where the active channel widened at channel bends displayed noticeable planform changes and increases in mapped bar area. From water year (WY; a 12-month period from October 1 through September 30 and named for the year in which it ends) 1906 to 2021, changes in the stage-discharge relation interpreted as rising and lowering channel bed levels were observed at the USGS streamgage 14305500 (Siletz River at Siletz, OR) in response to floods (such as high flows in February 1996 and January 2002 that exceeded 0.1 and 0.667 annual exceedance probabilities [AEP] events, respectively). However, the rating curve representing the stage-discharge relation did not change in response to high-magnitude floods between 2007 and 2021. Along the approximately 54-km of the Siletz River between Moonshine Park and the Bulls Bag area, surficial particle distributions varied considerably between sampling sites in response to changes in channel width and gradient, sediment inputs from tributaries, and basin geology. Despite this variability, median particle sizes tended to decrease in size in the downstream direction over the 54 km. Results of Objective Two, an evaluation of hydraulic and bedload transport conditions along the Siletz River, include the following The most substantial increases in maximum and mean water velocity and bedload sediment transport capacity occurred at events between the 0.995 and 0.50 AEPs. Events of these magnitudes occur approximately every 1–2 years. Smaller events (0.995 AEP) are generally contained by the banks of the main channel, whereas larger events (0.50 AEP) generally spill over the banks and inundate high-elevation bar and low-elevation floodplain surfaces. Multiple smaller floods within a WY that exceed the 0.995 and 0.50 AEPs (such as in WY 1996) can transport as much or more bed-material sediment than a single, higher magnitude event (such as the maximum event recorded in WY 2000 with an estimated AEP of around 0.002). Bedload transport capacity generally exceeds sediment supply (greater than 2 millimeters [mm]) for most of the study area from Wildcat Creek to the City of Siletz as evidenced by substantial in-channel bedrock. Despite overall conditions of limited sediment supply, transport capacity still varies considerably within and between years with discharge magnitude and spatially in relation to local hydraulics imposed by bedrock, channel morphology, and human infrastructure (such as bridges). Results of Objective Three, an analysis of PBH for lamprey larvae, include the following About 28 percent of the Siletz River network meets the mean annual suspended sediment loads and channel slope criteria for PBH. Along the main-stem Siletz River, in-channel bedrock outcrops and high transport capacity are expected to further constrain PBH. Together, these results suggest that most of the Siletz River between Wildcat Creek and the City of Siletz has had only modest vertical and lateral change between the 1930s and 2010s because of the bedrock in and along the main channel and the river’s relatively high transport capacity relative to bed-material sediment supply. However, localized sections of the Siletz River where the active channel widens, particularly at channel bends, exhibited some change in channel planform and the locations and area of gravel bars. In the future, moderate increases in autumn-winter discharge may not result in substantial changes in coarse gravel bars along the Siletz River but may result in selective transport of finer bed-material sediment (gravel, sands, and silts) that provide spawning habitats for Chinook salmon and Pacific lamprey and burrowing habitats for lamprey larvae. Assuming no substantial changes in bed-material sediment supply, increased bedload transport capacity may cause frequent entrainment of lamprey larvae that are burrowed in coarse sand deposits, suspension and downstream transport of salmon eggs incubating in gravels, and reductions in the areas of spawning gravels for Chinook salmon and Pacific lamprey. Exact implications of current and future discharge conditions for these species along the Siletz River depends on many factors, including sediment supply, local hydraulics, and the timing of flood events relative to fish life stages.

Oregon↗
USGS2026

Conventional hydrothermal power-producing systems of the Great Basin, USA

As part of the update to the electric-grade conventional hydrothermal assessment of the Great Basin, USA, Monte Carlo analyses of identified resources within explored regions will be performed to make estimates of discovered resources and associated uncertainty. Analyses use conditional statistics where estimates are conditioned upon a hydrothermal favorability map, allowing for the likelihood that more resources exist in regions of higher hydrothermal favorability. For these analyses, a dataset of identified hydrothermal systems is compiled, and the new compilation is described herein. Recognizing that a single hydrothermal system may be developed with multiple power plants, and that the hydrothermal upflow zone may be several kilometers across with many measurements characterizing a single hydrothermal system, a procedure was developed and employed to create clusters of points (power plants, measurements, etc.) that are associated with a single system, and a new central point was defined as the best estimator of the center of the hydrothermal system. Hydrothermal systems were uniquely identified by grouping electric-grade hydrothermal measurements and operating power plants within a distance of 10 km. Groups that are >10 km apart are assumed to be different electric-grade hydrothermal systems. While 10 km was used as the threshold, most systems were significantly further apart, and most points within groups were typically within 5 km of each other. A well measurement was considered an electric-grade measurement of a hydrothermal system if it had two properties: a measured temperature of >85 °C and evidence of hydrothermal convection. Other points that were added to the dataset are locations of operating powerplants or locations that have been classified as an electric-grade hydrothermal resource by either the U.S Geological Survey (USGS) or the Great Basin Center for Geothermal Energy. After all points are assigned to systems, new points were computed with the goal of identifying the center of the throat of the hydrothermal upflow zone. If operating powerplants exist for a system, then the arithmetic average of all power plant locations is used. Otherwise, if USGS made an estimate, that location is used. In the absence of both powerplants or USGS estimates, the arithmetic average of all electric-grade measurement locations is used. An example is shown of how these newly compiled locations might be ranked for uncertainty analyses, where higher confidence is assumed if measured temperature is higher and there are many supporting measurements indicating an electric-grade resource. In summary, 28 systems have operating power plants, an additional 78 systems are known identified electric-grade hydrothermal resources, and 99 new systems were identified as probable electric-grade systems with varying levels of confidence. These 205 locations are shown as a function of a recent hydrothermal favorability map, conceptually illustrating the conditional statistics that can be used to make estimates of the undiscovered resources of the Great Basin. An accompanying data release provides summaries of developed capacity by system and USGS estimates of likely total capacity and associated uncertainty.

Arizona, California, Idaho, Nevada, Oregon, Utah↗
USGS2026

Groundwater-level elevations in the bedrock aquifers of the Denver Basin aquifer system, Elbert County, Colorado, 2015–23

Water users in Elbert County, Colorado, rely on groundwater from bedrock aquifers in the Denver Basin aquifer system (upper Dawson, lower Dawson, Denver, Arapahoe, and Laramie-Fox Hills aquifers) for approximately half of their water uses. Withdrawals from the bedrocks aquifers have increased to meet the water use needs of expanding regional population growth and development. The U.S. Geological Survey, in cooperation with the Elbert County Board of County Commissioners, began a study in 2015 to monitor groundwater levels within Elbert County. The primary purpose of this report is to present a summary of groundwater levels measured during the study period (2015–23) and present results from statistical analyses of changes in groundwater-level elevations through time. Discrete groundwater levels were measured at 36 wells within Elbert County. Seven of those wells contained equipment to make and record continuous groundwater-level measurements at hourly intervals. All aquifers, except the lower Dawson aquifer, had only declining groundwater-level elevations in discrete measurements for wells with statistically significant trends. Of the eight statistically significant trends in the lower Dawson aquifer, two wells indicated increasing groundwater-level elevation from discrete measurements. The groundwater-level elevation trend medians in the upper Dawson, lower Dawson, Denver, Arapahoe, and Laramie-Fox Hills aquifers were −0.23, −0.66, −0.64, −0.39, and −0.63 feet per year, respectively, for discrete groundwater-level elevation measurements. Trends in continuous groundwater-level elevations were in agreement with statistically significant trends in discrete groundwater-level elevations for all wells. The groundwater-level elevation trend medians in this study, compared to the overall trends in a 2015−2018 study, both indicated declining groundwater-level elevations except in the upper Dawson aquifer, where the trend direction was opposite, a positive trend from 2015 to 2018 and a negative trend (declining groundwater elevations) from 2015 to 2023. The change in trends within the upper Dawson aquifer may be affected by differences in the study period and the trend analysis applied. Trends during the 2015–23 study period were compared to departures from the median 2015 groundwater-level elevation for each site in each aquifer. In general, the departures from the 2015 median supported trends observed at each site and correlated spatially with greater departures near the western border of Elbert County. Additionally, 30-year precipitation data showing wet and dry periods were overlaid with the departure from the 2015 median to assess groundwater-level patterns in wells in the five aquifers. Departures from the 2015 median groundwater-level elevations appeared greatest during the dry period between 2020 and 2023. Potentiometric-surface maps of the upper and lower Dawson aquifers created from static April 2023 groundwater elevations indicated groundwater-flow direction is generally from the south to the north. Results of this study could be used to guide additional groundwater monitoring in Elbert County and could aid in long-term planning of water resources.

Colorado↗
USGS2024

Hyperspectral (VNIR-SWIR) analysis of roll front uranium host rocks and industrial minerals from Karnes and Live Oak Counties, Texas Coastal Plain

VNIR-SWIR (400–2500 nm) reflectance measurements were made on the surfaces of various cores, cuttings and sample splits of sedimentary rocks from the Tertiary Jackson Group, and Catahoula, Oakville and Goliad Formations. These rocks vary in composition and texture from mudstone and claystone to sandstone and are known host rocks for roll front uranium occurrences in Karnes and Live Oak Counties, Texas. Spectral reflectance profiles, 569 in total, were reduced to 125 representative spectral signatures, which were analyzed using the U.S. Geological Survey's (USGS) Material Identification and Characterization Algorithm (MICA). MICA uses an automated continuum-removal procedure together with a least-squares linear regression to determine the fit of observed sample spectral absorption features to those of reference mineral standards in a spectral library. The reference minerals include various clay, mica, carbonate, ferric and ferrous iron minerals and their mixtures. In addition, absorption feature band-depth analysis was done to identify rock surfaces exhibiting absorption features related to uranium and zeolite minerals, which were not included in the command files used to execute MICA. Rocks from each of the four geologic units produced broadly similar spectral signatures as a result of comparable mineral compositions, but there were some notable differences. For example, Ca- and Na-montmorillonite was matched most frequently to the spectral absorption features in 2-μm (∼2000–2500 nm) wavelengths, while goethite occurred often at 1-μm (∼400–1000 nm) wavelengths. The latter is related to limonitic iron-staining in and around oxidized zones of the uranium roll front as described in previous papers. Rocks of the Jackson Group differed from those of the Catahoula, Oakville and Goliad units in that the former exhibited spectral features we interpret as being due to the presence of lignite-bearing mudstone layers. Goliad rocks exhibit spectral features related to dolomite, gypsum, anhydrite, and an unidentified green clay mineral that is possibly glauconite . Jackson Group rocks also exhibit weak but well-resolved absorption features at 964 and 1157 nm related to either or both zeolite minerals clinoptilolite and heulandite. These zeolite minerals and a few spectra exhibiting hydrous silica absorption features are indicative of alteration of volcanic glass in tuffaceous mudstone and claystone layers. A few sample spectra exhibited strong absorption features at around 1135 nm related to the uranium mineral coffinite. Both the 1135 nm coffinite and 1157 nm zeolite absorption features overlap somewhat, potentially making them difficult to distinguish without additional hyperspectral field, laboratory or remote sensing data. The results of this study were compared to mixtures of minerals described for ore, gangue and alteration minerals in deposit models for sandstone-hosted uranium, sedimentary bentonite and sedimentary zeolite. Use of these spectra can help facilitate mapping of both waste materials from the legacy mining of the above commodities, as well as future exploration and resource assessment activities.

Texas↗
USGS2025

Preliminary field report of landslide hazards following Hurricane Helene

Executive Summary This report reflects our knowledge regarding the widespread landslide activity associated with Hurricane Helene observed during the U.S. Geological Survey’s (USGS) mission assignment to North Carolina in October 2024. The material in this report was originally prepared for the Federal Emergency Management Agency under mission assignment DR-4827-NC. The data and commentary in this report are reflective of a report provided to the Federal Emergency Management Agency (FEMA) on October 18, 2024, as well as information provided in briefings at the Buncombe County Emergency Operations Center. The report has been modified for public dissemination. This assessment was based on systematic visual examination and mapping of landslide locations from aerial and satellite imagery, visual and photographic observations from low-level helicopter overflights and conversations with local landslide experts from the North Carolina Geological Survey and Appalachian Landslide Consultants PLLC, and more than 50 years of combined landslide hazard professional experience of the mission-assigned field team. No systematic field investigations were done by the USGS. While responding to the event, the USGS did not identify any landslides that posed an immediate major threat to recovery personnel in parts of nine counties in North Carolina (Avery, Buncombe, Henderson, McDowell, Mitchell, Polk, Rutherford, Watauga, and Yancey); however, threats from renewed landslide activity may remain heightened in localized areas for months or even years. Known areas of the most abundant landslide occurrence include Bat Cave, Lake Lure, Chimney Rock, Swannanoa, Black Mountain, Fairview, steep areas in Asheville, and the Blue Ridge Parkway. The USGS shared detailed locations of known landslides with the Emergency Operations Centers. The thousands of landslide scars on hillsides and landslide deposits on flatter ground may present some threat to recovery activities. Soil and rocks will continue to erode from newly exposed landslide scars and may pose a threat to people and infrastructure who are immediately nearby. In general, the steeper and taller the landslide scar, the greater the potential threat. This threat is heightened during periods of rainfall and increases with the duration and intensity of rainstorms. Very heavy rainfall, or repeated rainfall events during short periods, could also initiate new landslides on steep slopes. Excavation of landslide deposits, particularly excavation of those deposits directly adjacent to steep slopes, may also pose a threat to nearby people and equipment. An interagency collaborative mapping effort led by the USGS that informed this assessment identified 1,155 landslide locations by the October 2024 briefings, but that number increased to 2,217 in a final reviewed version of the locations published in January 2025. Locations were mapped from satellite imagery, fixed-wing and helicopter surveys, media and social media, and field reports in the 3 weeks following the passage of the remnants of Hurricane Helene. USGS products outlined in this report are publicly available and include geotagged photographs from aerial reconnaissance, hazard models, an interactive view of mapped landslide locations, and landslide safety and education resources.

North Carolina, South Carolina, Tennessee, Virgini↗
USGS2024

Three-dimensional temperature maps of the Williston Basin, USA: Implications for deep hot sedimentary and enhanced geothermal resources

As part of U.S. Geological Survey's (USGS) efforts to identify and assess geothermal energy resources of the US, a three-dimensional (3D) geologic and thermal model has been constructed for the Williston Basin, USA. The geologic model consists of all sedimentary units above the Proterozoic and Archean crystalline rock (called basement herein), with a total sedimentary thickness of up to 5 km near the basin center. Twenty-nine geologic units were mapped from interpreted formation tops from 16,465 wells. A 3D temperature model was constructed to a depth of 7 km by constructing a 3D heat flow model for the sedimentary units, followed by estimating underlying temperature using a one-dimensional (1D) analytic solution for heat flow within the underlying crystalline basement. Using the sedimentary basin model, heat flow was simulated in 3D and was calibrated using three temperature datasets: 1) 24 high-confidence static temperature logs (equilibrium thermal profiles), 2) more than15,000 drill stem test (DST) measurements from >7,000 wells, and 3) more than 45,000 bottomhole temperature (BHT) measurements from >14,000 wells. The DST and BHT datasets provide broad spatial coverage, but are lower confidence, primarily because measurements were made prior to attaining thermal equilibrium. DST and BHT measurements were binned regionally to develop representative thermal profiles that generally agree with these lower quality data (hereafter called pseudowell temperature profiles). Layer properties (primarily thermal conductivity and compaction curves) were set to best estimate values, then the heat flow model was calibrated to fit pseudowell and static temperature logs primarily by adjusting basal heat flow to approximate the overall temperature profile. Minor adjustments to thermal conductivity allowed adjusting changes in slope at lithologic contacts. Resulting maps include 3D temperature and basal (bottom of sedimentary units) heat flow estimates, which are used as input for the temperature model of the basement. The crystalline basement temperature model uses an analytic 1D solution to the heat flow equation that requires estimates of heat flow and temperature at the upper boundary (i.e., the sediment/basement contact), radiogenic heat production within the crystalline basement, and reference thermal conductivity (i.e., uncorrected for temperature). Two regions of high heat flow are identified: 1) in western North Dakota along the North American Central Plains Conductivity Anomaly and 2) in eastern Montana near the Poplar dome. Within the sedimentary column in the center of the basin of the basin, an area of approximately 100,000 km2 is predicted to have moderate- to high-temperature geothermal resources (>90 °C) under the thickest sequences of sediments. Where thick insulation and high heat flow coincide, electric-grade resources can be less than 4 km deep. Assuming a maximum feasible drilling depth of 7 km, temperatures are predicted to be as high as 175 °C. The geologic model may be used to identify strata at sufficient temperatures that may have natural permeability or that may have conditions that favor development of enhanced/engineered geothermal systems resources.

Montana, North Dakota, South Dakota↗