Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Geologic Investigation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

922 records · Page 50Linked to original sources
USGS2026

Development of liquefaction-targeted design basis in U.S. seismic provisions

Seismic design criteria for new buildings in the United States have historically focused on life safety performance objectives through minimizing the potential for structural collapse. Development of design criteria to meet this performance objective has evolved over time, leading to the current, risk-targeted maximum considered earthquake (MCE R ) design basis. Corresponding MCE R seismic design loads incorporate the full range of probabilistic ground motion hazard information available from U.S. Geological Survey National Seismic Hazard Models, as well as a representation of the uncertainty in structural collapse capacity. Despite these considerable advances in structural design criteria, guidelines for geotechnical hazards such as liquefaction-induced damage, which continue to be based on uniform ground-shaking hazard (i.e., MCE ground motions), are not well-connected with risk-based, collapse prevention performance objectives. This study, undertaken as part of Building Seismic Safety Council efforts to update recommended seismic provisions through the National Earthquake Hazards Reduction Program, presents probabilistic, liquefaction-targeted design objectives and corresponding ground motion parameters, with a focus on improving consistency in first-level screening criteria for liquefaction hazard assessment. This study identifies a potential maximum acceptable annualized probability of liquefaction triggering ( P L,max ) of 2.5% in 50 years, above which liquefaction consequences and potential mitigation measures would be considered. The P L,max -based design basis is calibrated to effective probabilistic liquefaction hazard levels obtained in practice using current MCE peak ground accelerations, and could be implemented via a new liquefaction-targeted maximum considered earthquake (MCE L ) peak ground acceleration ( PGA L ). The proposed PGA L is derived from probabilistic liquefaction hazard curves and includes uncertainties inherent to liquefaction hazard modeling. The potential design effects of the proposed PGA L are demonstrated via comparison with current MCE PGA levels, effects on first-level liquefaction screening analyses, and improvements in the consistency of P L,max levels across the United States, and for a wide range of site conditions.

conterminous United States↗
USGS2026

Site-specific amplifications in Northwestern Turkiye: A generic approach

In this study, we derive generic site amplification functions applicable to Northwestern Türkiye and follow guidance on site classifications established by the United States National Earthquake Hazards Reduction Program (NEHRP). We employ the one-dimensional (1-D) equivalent linear ground response analysis method and focus on recordings from a select suite of free-field strong motion (SM) stations. These particular SM stations are associated with a comprehensive geotechnical site conditions dataset comprising 76 shear-wave velocity profiles. Despite their varying resolutions and depths, this diversity allows for a more representative analysis across different site conditions, enhancing the robustness of our findings. For analyses, we utilize a robust set of global ground motion records, selected from both within and outside of Türkiye, to serve as strong and weak input bedrock motions. Site amplification is determined by propagating these bedrock records through 76 site-specific Afet ve Acil Durum Yönetimi Başkanlığı (AFAD) station profiles and calculating the spectral acceleration ratio between the ground surface and the input motion. Our analyses reveal substantial disparities between the amplification functions derived from 1-D site response analyses using strong and weak input motions. These disparities are central to our analysis and inform the subsequent comparison with site amplification functions reported in the literature. We compare the generic site amplification functions derived in this study with those reported in the literature for regions with similar geological and seismic conditions to Northwestern Türkiye. For example, site amplification functions for NEHRP Site Classes C and D have been documented for Greece and the United States utilizing frequency-dependent methods such as the quarter-wavelength approximation. Our findings reveal that the generic site amplification functions derived in this study exhibit differences in peak amplitudes and predominant frequencies compared to those in the literature, reflecting regional variations in geotechnical and seismic properties. This study represents an initial effort to formulate generic site amplification functions for Türkiye, with a particular emphasis on the Northwestern region. A thorough literature review indicated no prior studies have proposed such functions specifically for this area.

Northwestern Turkiye↗
USGS2025

Climate change and future water availability in the United States

The steady rise in global temperature as a result of human activity is causing changes in Earth’s water cycle. The balance of water stored within and moving between vapor, liquid, and frozen states in the water cycle is shifting, with consequences for water availability that include increases in drought, fire weather, flooding, and heavy precipitation, as well as cryosphere decline and sea-level rise. In this chapter of the U.S. Geological Survey Integrated Water Availability Assessment—2010–20, we provide an overview of climate-change observations and projections from Earth-system model simulations that relate to future water availability, from global and national climate assessments and from the published literature. Effects of climate change on primary water-cycle components are discussed in context of how global-scale hydroclimate drivers influence regional processes within the United States. Understanding the major climate drivers impacting the water cycle is crucial to predicting future changes in water availability and developing adaptation strategies to ensure human and ecosystem water supplies. First, we provide background information on the water cycle, the climate-model ensemble simulations developed to produce projections based on warming scenarios, and attribution and certainty levels. Tipping points, self-reinforcing feedbacks, cascading effects, and compound extremes are introduced. The framework of climatic impact drivers (CIDs) outlined in the Intergovernmental Panel on Climate Change Sixth Assessment Report (IPCC AR6) is used to show primary drivers of physical change to the water cycle and to understand and predict changes in future water availability. Specific climate-change related observations and projections are discussed for water cycle components of precipitation, evapotranspiration, soil moisture, streamflow, lakes and wetlands, ice and snow, and groundwater, as well as their implications for future water availability for humans and ecosystems. The chapter concludes with a synthesis discussion of three examples of complex regional-scale hydroclimate processes that influence water availability for populations in the United States, including (1) mountain and coastal precipitation, (2) aridification and drought, and (3) the influence of forest-cover change on terrestrial water-vapor recycling.

Professional Paper↗
USGS2025

Mapping potential sensitivity to hydrogeomorphic change in the UMRS riverscape

In 2020 the U.S. Geological Survey (USGS), as part of the Upper Mississippi River Restoration (UMRR) Program, began a new project to characterize potential hydrogeomorphic change associated with hydrogeomorphic units (HGUs) and their catenae (units linked by their association with sediment sources and flow origins). The goal of the project was to develop a geographic information system (GIS) database of HGUs for the Upper Mississippi River System (UMRS) available to both scientists and river managers working on UMRR studies and HREP planning and design studies. The characterization was based on a hydrogeomorphic change hierarchical classification developed previously for the UMRS. The products were generated with automated techniques in a GIS using systemic datasets. Landforms were mapped from the 2015 UMRS topobathymetric dataset with geomorphon (shape-based) tools tailored for the large riverscape, valley bottom environments in the UMRS. A clustering analysis was applied to the resulting landforms to identify HGUs associated with zones of perennial low flows, bankfull flows, and overbank floodplains. Catenae were assembled based on the proximity of the units to the main channel, tributary mouths, and side channels from previously published aquatic areas (USACE, 2018) coupled with least-cost flowpath linkages between potential sediment origins and planform change units developed by Rogala, Fitzpatrick, and Henderson (2020). These GIS-based analyses were successful at identifying a range of HGUs using an automated technique with available data across the entire riverscape, with emphasis on those that have the potential for hydrogeomorphic change. Most of the resulting features are depositional, as expected in a large river system. However, this is the first attempt of linking tributary inputs, side channel erosion and levee breaches with their depositional counterparts. The approach was successfully piloted in Pools 8 and 10 in the Upper Impounded Reach and Pool 14 in the Lower Impounded Reach, with next steps for application in reaches of the unimpounded section and Illinois River. This report emphasizes results from Pool 10, which was the focus of most of our attention during the pilot phase.

Illinois, Indiana, Iowa, Minnesota, Missouri, Sout↗
USGS2025

Land cover change within wetland complexes at Dixie Meadows, Churchill County, Nevada: 2015 – 2023

Dixie Meadows, Nevada, is a system of geothermal springs and seeps that feed a complex of marshes and wetland meadows that are located within lands managed by the Bureau of Land Management (BLM) and the Department of Defense (DOD). A previous U.S. Geological Survey report documented variability in satellite imagery-based land cover classifications for seven wetland complexes at near monthly time intervals between October 2015 and January 2022. This report presents additional data, extending analysis to November 2023. Land cover classifications between October 2015 and November 2023 demonstrated an association between vegetation cover characteristics and surface moisture, with Class 1 having dry, bare soil or sparse upland vegetation, Class 2 having moist, bare soil or sparse to small vegetation, Class 3 having dense green vegetation with potentially saturated soil conditions, Class 4 having a mix of shallow surface water, saturated soil, and dense green vegetation, and Class 5 having open surface water. Most of the wetland complexes occur close to spring outflows primarily within land managed by the DOD, though portions are also within BLM lands. The intervening and surrounding landscape outside of the wetland complexes assessed in this study are managed by the BLM. As a result, Class 1 land covers had the largest areal coverage for BLM managed lands. Classes 2 and 3 land covers were primarily mapped inside the wetland complexes and thus had the largest area coverage within DOD managed lands. Class 4 was almost exclusively mapped within the wetland complexes and thus was largely contained within DOD managed lands. Class 5 (open water) was exclusively mapped in and adjacent to a single wetland complex with catchment ponds on land managed by the BLM. The distribution of these land cover classes over the study period was seasonally and annually variable. Land cover areas of Classes 1 and 2 were larger during the spring months. Conversely, land cover areas of Classes 3 and 4 tended to be greatest during the summer or fall. These patterns might be influenced by differences in seasonal water sources and phenology.

Nevada↗
USGS2025

Near-surface material and topography generate anomalous high-frequency ground motion amplification in Chugiak, Alaska

An ∼3 km long nodal array oriented approximately east–west was deployed in Chugiak, Alaska, by the U.S. Geological Survey during 2021. The array intersects with the permanent NetQuakes station NP.ARTY, where peak ground acceleration (PGA) value of 1.98 g was recorded during the 2018 M w 7.1 Anchorage, Alaska, earthquake, in sharp contrast to the PGA of ∼0.3 g at a site just 4 km to the west. Seismic data for M w 1.8–4.3 aftershocks from the M w 7.1 event recorded by the nodal array confirm the anomalously large ground motions obtained at NP.ARTY as well as similar amplifications at nodes within ∼1 km to the east. Here, we performed 0–10 Hz 3D finite‐difference simulations, including high‐resolution surface topography, to explore the cause of the unexpectedly large amplification. As expected, the simulations computed with a regional 3D tomography velocity model severely underpredict the 0–10 Hz acceleration records at almost all sites. Adding a near‐surface low‐velocity taper to 300 m depth amplifies the accelerations by up to a factor of 5 and enables a reasonable match between the nodal data and simulations at sites to the west of NP.ARTY. However, this model still underpredicts the spectral energy in the area covered by glacial sediments by up to an order of magnitude. The addition of a till layer using a depth‐dependent shear‐wave velocity ( ⁠⁠ V s ) profile along with a homogeneous, 8 m thick low‐velocity layer with V s = 250 m/s representing the kame terraces improves the fit to data to within a factor of 2 at nodes located on top of the glacial sediments. Our study shows that the anomalously large high‐frequency amplification recorded at and near NP.ARTY can be explained by a combination of topographic effects and near‐surface low‐velocity material with amplification effects on the high‐frequency ground motion by up to about 40% and an order of magnitude, respectively.

Alaska↗
USGS2025

Pre-Acadian tectonics of the eastern Orange-Milford Belt, south-central Connecticut

This excursion presents a reinterpretation of mapping and new analytical data from the eastern Orange-Milford belt (OMB) in south-central Connecticut. The OMB is a fault-bound terrane of argillites and mafic rocks of anomalously low metamorphic grade—and of poorly constrained ages and tectonic affinity—wedged between kyanite/sillimanite-grade peri- Laurentian rocks to the west and anatectic peri-Gondwanan rocks to the east (Fig. 1A). Our data demonstrate that Ordovician(?) igneous and sedimentary rocks of the OMB were variably metamorphosed in the Ordovician and Silurian but escaped regionally pervasive, high-grade Devonian and later metamorphism. Previous interpretations (Fritts 1963a, 1965a, 1965b; Burger, 1967; Burger and others, 1968; Rodgers, 1985) described these rocks as a conformable sequence of low-grade, Ordovician to Devonian metasediments and metavolcanics. Our results reveal that the “metavolcanics” are not extrusive rocks but rather slivers of lower oceanic crust with complicated high- and low-grade metamorphic fabrics, intruded by a swarm of Silurian sheeted basalt dikes, and in fault contact with the surrounding metasediments. The purpose of this trip is to show evidence of early Paleozoic (Taconic) deformation and metamorphism preserved in rocks of the eastern OMB. These rocks remained shallow, cool, and sufficiently dry during the regionally dominant Acadian and Alleghanian orogenies to have avoided significant overprinting. As such, these rocks serve as windows into a geologic history otherwise unavailable between anatectic rocks of the peri-Gondwanan Bronson Hill, Avalon, and Gander terranes east of the Hartford basin and sillimanite-grade rocks of the peri-Laurentian Hartland and gneiss dome belts west of the OMB. We present major and trace element geochemistry including rare-earth element patterns for all mafic units in the eastern OMB as well as 40 Ar/ 39 Ar age spectra of amphibole, muscovite, and K-feldspar from rocks of the Maltby Lakes complex (of Deasy and others, 2017), Savin Schist, and Wepawaug Schist. Our evidence demonstrates that the units of the OMB have been assembled by faulting or intrusion, and that no stratigraphic relationships exist between the argillaceous schists and the metaigneous rocks.

Connecticut↗
USGS2023

Oligocene–Miocene northward growth of the Tibetan Plateau: Insights from intermontane basins in the West Qinling Belt, NW China

Growth of the Tibetan Plateau, Earth’s broadest and highest elevation collisional system, shapes orographic barriers, reorganizes drainage networks, and influences surface erosion and sediment delivery, whose changes in space and provenance feed back to intracontinental tectonic processes. Studies of interior basins within the northern Tibetan Plateau provide new sediment accumulation, provenance, paleodrainage, and deformation timing data that enable a reconstruction of the far-field tectono-geomorphic evolution of the rising Tibetan Plateau. Along the northern plateau margin, topographic growth in the West Qinling Belt is inferred to have initiated in the Eocene, nearly coeval with the India-Asia collision, as well as in the late Miocene. However, geological knowledge about the intervening period remains at present enigmatic, and the kinematics and dynamics are uncertain. This study presents a multidisciplinary data set from the intermontane Anhua-Huicheng Basin (AHB; Gansu Province, China) to fill this gap. Magnetostratigraphic dating, regional mapping, and sedimentological analysis imply that contractional deformation and thrust-top basin systems formed within the West Qinling Belt in the Oligocene (not later than ca. 24 Ma). A combination of observations including paleocurrent changes, detrital zircon U-Pb age variations, and appearance of growth strata along the Anhua-Huicheng Basin reveal the rapid uplift of the West Qinling Belt at ca. 15 Ma. Sedimentation in the intermontane basins ended after the late Miocene (ca. 8 Ma), when the region experienced intrabasinal deformation, uplift, and erosion with the establishment of an external drainage system. Since the late Miocene, the growth of the West Qinling Belt reached a climax with the lack of substantial contractional deformation in Cenozoic sequences heralding the onset of the modern kinematic regime and attainment of high elevation. Observed transitions in the tectonostratigraphy and paleodrainage define different phases of deformation and plateau-wide shifts in stress reorganization, which led to the northward growth and later lateral expansion of the Tibetan Plateau.

GSA Bulletin↗
USGS2025

Insights and strategic opportunities from the USGS 2024 Per- and Polyfluoroalkyl Substances (PFAS) Interagency Workshop

Introduction In 2021, the U.S. Geological Survey (USGS) published Circular 1490 titled, “Integrated Science for the Study of Perfluoroalkyl and Polyfluoroalkyl Substances (PFAS) in the Environment: A Strategic Science Vision for the U.S. Geological Survey” (Tokranov and others, 2021). Circular 1490 was created to be a resource for USGS scientists prioritizing and planning research related to per- and polyfluoroalkyl substances (PFAS) and to be a guide for developing partnerships with other scientists, State and Federal agencies, and stakeholders engaged in PFAS research and management and mitigation of the environmental and human-health effects of PFAS. This USGS PFAS Strategic Science Vision document was intended to be the foundation for a “living strategic vision,” periodically providing updates on the state of USGS PFAS research, emerging PFAS data gaps and needs, and progress on interagency and stakeholder PFAS partnerships and priorities. To meet this objective, the USGS planned to host an Interagency and Stakeholder PFAS Workshop every 2–3 years. During September 10–12, 2024, the USGS hosted the first Interagency and Stakeholder PFAS Workshop in Reston, Virginia. The Workshop brought together experts from other Federal agencies (U.S. Environmental Protection Agency, National Institute of Environmental Health Sciences, Food and Drug Administration, Department of Defense [Air Force, Army]), State agencies (Washington Fish and Wildlife, Virginia Department of Transportation), and academia (Harvard University, University of Maryland) to address key challenges relating to the measurement and modeling of PFAS and the implications for environmental health. Participants engaged in in-depth discussions centered around six pivotal topics related to PFAS: (1) sampling protocols, methods and interpretation; (2) environmental sources, source apportionment, and occurrence; (3) environmental fate and transport; (4) human and wildlife exposure routes and risk; (5) bioconcentration, bioaccumulation, and biomagnification; and (6) ecotoxicology and effects. Each topic had three breakout sessions. A recurrent theme of workshop discussions was how data on a nationwide scale for PFAS occurrence in various environmental matrices, including air, water, food crops, biota, soil, and streambed sediment could help to advance scientific understanding. Participants noted significant geospatial data gaps, particularly in the midwestern and southern United States and the Pacific Northwest. PFAS data collection tends to be more robust along the eastern seaboard and in California. Participants stressed how enhancing the integration of large and small datasets across various agencies could help to support national scale understanding of PFAS. To address these gaps, attendees suggested leveraging datasets from Federal entities like the USGS and the U.S. Department of Defense, State agencies, and municipal utility services to develop predictive contaminant detection and transport models. Improved coordination between water quality programs and USGS research could help to facilitate access to valuable data, leading to comprehensive databases that inform PFAS point (wastewater treatment plants and landfills) and nonpoint (runoff from land, atmospheric deposition, food packaging) sources, environmental transport mechanisms, environmental detection and concentrations, potential exposure routes, and health effects on different biota, including humans. A specific request was made to develop a map demarking the depth of modern (1953 or later) groundwater, which is susceptible to surface-derived anthropogenic (that is, human-made) contamination, based on tritium-age dating. Emphasis was placed on incorporation of hydrology, groundwater flow paths, groundwater–surface water interactions, and landscape factors in predictive statistical models as a step to improve contaminant source identification and tracking. Molecular fingerprinting approaches garnered attention as techniques to link specific PFAS mixtures detected in a sample to environmental sources and levels in biota (Dávila-Santiago and others, 2022). Integrating data from abiotic (that is, water, soil, and air) and biotic (that is, living organisms) systems identified as a research opportunity. For example, understanding the composition of soils and sediments, which include a mixture of mineral, plant, and animal components, could advance understanding of exposure pathways. The discussions highlighted opportunities to explore and understand the potential redistribution and biotic exposures of PFAS from biosolid and wastewater treatment plant effluent land application practices, in addition to atmospheric releases and discharges from landfill and wastewater treatment plants. Participants identified research gaps surrounding how these sources may contribute to contamination and may affect surrounding ecosystems, including a better definition of anthropogenic background concentrations. Moving forward, the collection of co-occurrence data was noted as a means to improve understanding of complex mixtures and to leverage companion modeling efforts focused on areas with high and low contamination levels to identify areas of concern and unaffected resources. Participants emphasized how centralized USGS databases and the establishment of sample-metadata archives can help to ensure that samples are preserved and accessible for future research. In conclusion, the workshop participants identified opportunities to bridge data gaps and improve measurement techniques, modeling frameworks, databases, and communication, to enhance the understanding of PFAS and their effects on environmental and human health. Upon completion of the workshop, participants indicated an interest in developing strategic data collection, modeling, and analytical approaches to address these challenges.

Open-File Report↗
USGS2025

Stratigraphy, structure, and geomorphology of the central Appalachians across the North Mountain fault zone near Harrisonburg, Virginia, USA

This field trip focuses on the geology of the central Appalachian Valley and Ridge province near Harrisonburg, Virginia, USA. Recent geologic mapping utilizing 1-m resolution lidar data has revealed new insights into the Paleozoic stratigraphy, structural geology, and Neogene landscape evolution of the region. The detailed mapping reveals the presence of the Big Spring Station Member and multiple thrombolite zones in the Cambrian Conococheague Formation extending as far south as the Briery Branch 7.5 min quadrangle, providing insights into Late Cambrian sea-level fluctuations. Multiple outcrop exposures in the study area of this guidebook confirm recent work in Pennsylvania, USA, showing that the Ordovician Reedsville Shale overlies the Martinsburg Formation and that the two are distinct and mappable as separate formations rather than laterally equivalent units as previously interpreted. Our work extends the Silurian Williamsport Sandstone into Shenandoah County, Virginia, and describes its facies relationships with the Bloomsburg Formation along strike and across the Adams Run anticline. Mapping within the thick Devonian siliciclastic sequence reveals the presence of the Mahantango Formation on the western limb of Supin Lick syncline and illustrates its complex facies relationship with the Millboro Shale. In addition, we highlight new mapping criteria for the Brallier and Foreknobs Formations and demonstrate how the specific changes to the placement of the contact between them addresses previous challenges in their differentiation. We present cosmogenic burial ages of broad alluvial fan sediments in the Shenandoah Valley near Timberville and Briery Branch, Virginia, and erosion rates estimated for the Briery Branch stream basin. Both analyses provide new constraints on the timing of landscape evolution and karst development since the middle Pliocene. This field guide also highlights some significant structural features within the North Mountain fault zone, such as evidence of imbricated thrust sheets cut by cross-strike faults that have been exploited by Eocene igneous intrusions. Map-scale horses of Silurian and Ordovician rocks hold up ridges that are oblique to the regional strike. Deformation internal to one of these horse blocks is shown to be non-coaxial with respect to the main regional northwest directed transport.

Virginia↗
USGS2025

ShakeAlert®—Communication, education, outreach and technical engagement strategic vision

Executive Summary In 2006, the U.S. Geological Survey (USGS) began directly supporting ShakeAlert ® research and in 2012 the ShakeAlert demonstration system began testing ( Given and others, 2018 ). The ShakeAlert earthquake early warning (EEW) system is a partnership between the U.S. Geological Survey (USGS) and the three West Coast States (Washington, Oregon, and California) served by the ShakeAlert System, which is part of the larger Advanced National Seismic System (ANSS). With more than 143 million people exposed to potentially damaging shaking in the United States ( Jaiswal and others, 2015 ), earthquakes are a national hazard. Most of our Nation’s earthquake risk is concentrated in the highly populated areas on the active plate tectonic boundaries on the West Coast of the conterminous United States. ShakeAlert is the first public alert system in the United States to provide rapid mass notification of earthquake detection, potentially offering seconds of warning before strong shaking arrives. A few seconds may not seem like much time, but the information in ShakeAlert Messages can be used to trigger automated actions that can prevent injury or death, reduce immediate damage, and speed recovery from earthquakes. The information product issued by the ShakeAlert system is called a ShakeAlert Message and is one of the information products and tools of the ANSS. The ShakeAlert System includes the USGS component, plus the pathways by which ShakeAlert-powered products and (or) services are delivered to end users. Alerts can be delivered to cell phones or be used to trigger automated systems to protect equipment, facilities, and infrastructure, such as slowing or stopping a train. ShakeAlert-powered automated actions can include fire house doors that can be opened to prevent jamming, heavy equipment (for example, trains, elevators, and cranes) that can be automatically stopped or parked in safe positions, and pipeline valves that can be closed to prevent surges and spills. A few seconds of warning also may be sufficient for people to take protective actions, such as drop, cover, and hold on or modified protective actions for a broad range of populations. Advance training may increase the benefit of a speedy response to an alert. Outreach and education about EEW may raise awareness of the overall earthquake threat and how people can best react when they receive an alert or feel shaking. ShakeAlert communication, education, outreach, and technical engagement (CEO&TE) efforts are highly collaborative and essential for the success of the ShakeAlert System. This strategic vision informs how the vast ShakeAlert CEO&TE Community operates and works together. The CEO&TE Community delineates a strategic framework that is intended to set the path for a long-term, sustainable approach to CEO&TE through three focus areas and five priorities. Focus Areas Technical engagement.— The objective of this focus area is to expand and broaden ShakeAlert technical engagement and implementation. External engagement.— This focus area targets engagement in long-term communication, education, and outreach planning, implementation, and evaluation. Internal engagement.— The purpose of this focus area is to build and sustain a robust infrastructure to optimize collaboration, information sharing, and project planning among the community of stakeholders charged with implementing ShakeAlert CEO&TE. Priorities The enumeration of the five priorities listed below does not suggest priority ranking. Public safety, preparedness, and resilience; Technical implementation and engagement; Consistent messaging and communication; Integration with other Federal and State earthquake hazards products; and Educational resources development and dissemination. This strategic vision is a tangible outcome of collaboration among many stakeholders beginning in July 2016. Since then, the work of the ShakeAlert CEO&TE Community has grown into an international effort. The USGS has developed, tested, and implemented a broad spectrum of communication, education, and outreach tools and resources—all of which recognize that seconds matter when it comes to safety and mitigating harm from earthquake hazards. The CEO&TE social science research effort has provided invaluable insights into the ShakeAlert System’s human interface. USGS-licensed technical partners develop, test, and implement real-world applications using ShakeAlert Messages. The success of ShakeAlert CEO&TE efforts is predicated on robust collaboration across numerous agencies, organizations, and groups. As such, this strategic vision outlines a “partnership model” that delineates roles and responsibilities to ensure alignment with focus areas and priorities. The partnership model includes the CEO&TE lead agency (USGS); its principal partners (State agencies and university partners); its implementation partners (for example, technical partners who build systems to deliver ShakeAlert-powered products and (or) services [focus area one]), earthquake education partners who work to increase public preparedness for seismic events (focus area two); and other organizations that work together to enhance the adoption and effectiveness of the ShakeAlert System. These partners collaborate and convene through a variety of working groups and forums, which are also described in this strategic vision and align with focus area three (internal engagement). The CEO&TE Community collaboratively developed its operating principles and a consensus-based, decision-making strategic framework to guide its collective work. Performance metrics are used to continually measure success. Ultimately, the USGS and ShakeAlert CEO&TE Community are advancing the ShakeAlert System that as of the publication of this strategic vision to “provide earthquake early warning for all” serves more than 50 million people.

Circular↗
USGS2025

Overview of The SCEC/USGS Community Stress Drop Validation Study using the 2019 Ridgecrest earthquake sequence

We present initial findings from the ongoing Community Stress Drop Validation Study to compare spectral stress‐drop estimates for earthquakes in the 2019 Ridgecrest, California, sequence. This study uses a unified dataset to independently estimate earthquake source parameters through various methods. Stress drop, which denotes the change in average shear stress along a fault during earthquake rupture, is a critical parameter in earthquake science, impacting ground motion, rupture simulation, and source physics. Spectral stress drop is commonly derived by fitting the amplitude‐spectrum shape, but estimates can vary substantially across studies for individual earthquakes. Sponsored jointly by the U.S. Geological Survey and the Statewide (previously, Southern) California Earthquake Center our community study aims to elucidate sources of variability and uncertainty in earthquake spectral stress‐drop estimates through quantitative comparison of submitted results from independent analyses. The dataset includes nearly 13,000 earthquakes ranging from M 1 to 7 during a two‐week period of the 2019 Ridgecrest sequence, recorded within a 1° radius. In this article, we report on 56 unique submissions received from 20 different groups, detailing spectral corner frequencies (or source durations), moment magnitudes, and estimated spectral stress drops. Methods employed encompass spectral ratio analysis, spectral decomposition and inversion, finite‐fault modeling, ground‐motion‐based approaches, and combined methods. Initial analysis reveals significant scatter across submitted spectral stress drops spanning over six orders of magnitude. However, we can identify between‐method trends and offsets within the data to mitigate this variability. Averaging submissions for a prioritized subset of 56 events shows reduced variability of spectral stress drop, indicating overall consistency in recovered spectral stress‐drop values.

California↗
USGS2026

Streamflow, water quality, and constituent loads and yields, Scituate Reservoir drainage area, Rhode Island, water year 2023

As part of a long-term cooperative program to monitor water quality within the Scituate Reservoir drainage area, the U.S. Geological Survey, in cooperation with Providence Water (formerly the Providence Water Supply Board), collected streamflow and water-quality data in tributaries to the Scituate Reservoir, Rhode Island. Streamflow and concentrations of chloride and sodium estimated from records of specific conductance for 16 tributaries were used to calculate loads of chloride and sodium during water year 2023 (October 1, 2022, through September 30, 2023). Water-quality samples were collected by Providence Water at 38 sampling stations on tributaries to the Scituate Reservoir during water year 2023. These water-quality data are summarized by using values of central tendency and are used, in combination with measured (or estimated) streamflows, to calculate loads and yields of selected water-quality constituents for water year 2023. Annual mean streamflows for monitoring stations in this study ranged from 0.47 to 34.4 cubic feet per second during water year 2023. At the 16 continuous-record streamgages, tributaries transported about 3,000 metric tons of chloride and 1,900 metric tons of sodium to the Scituate Reservoir; annual chloride yields for the tributaries ranged from 19 to 200 metric tons per square mile, and annual sodium yields ranged from 13 to 120 metric tons per square mile. At the stations where water-quality samples were collected by Providence Water, the medians of the median daily loads were 65,000 million colony forming units per day for coliform bacteria, 870 million colony forming units per day for Escherichia coli , 200 kilograms per day for chloride, 8.2 grams per day as nitrogen for nitrite, 520 grams per day as nitrogen for nitrate, and 300 grams per day as orthophosphate for phosphate. The medians of the median yields were 25,000 million colony forming units per day per square mile for coliform bacteria, 600 million colony forming units per day per square mile for Escherichia coli , 65 kilograms per day per square mile for chloride, 4.6 grams per day per square mile as nitrogen for nitrite, 180 grams per day per square mile as nitrogen for nitrate, and 180 grams per day per square mile as orthophosphate for phosphate.

Rhode Island↗
USGS2026

Final project peport for “Mapping riparian vegetation response to climate change on the San Carlos Apache Reservation and Upper Gila River watershed to inform restoration priorities: 1935 to present – Phase 2: Focus on tamarisk vegetation”

Riparian ecosystems play a critical role in supporting wildlife habitats, maintaining water quality, and sustaining ecological resilience in arid landscapes. In the Upper Gila River level-4 Hydrologic Unit Code (HUC-4; Identification Number – 1504) watershed of Arizona and New Mexico, and across areas of the San Carlos Apache Tribe of the San Carlos Apache Reservation (hereafter, Tribe/Tribal – entity; or Reservation - place), riparian ecosystems have been substantially altered by the widespread expansion of tamarisk ( Tamarix spp.), an invasive and non-native riparian species. Tamarisk has high water use and increased flammability, making it a growing concern as droughts intensify across the southwestern United States (U.S.). Recent research indicates that tamarisk is increasingly stressed under prolonged drought conditions, which can elevate wildfire risk and further degrade riparian habitat. In response, the U.S. Geological Survey (USGS) Western Geographic Science Center, in collaboration with the Tribe, developed remote sensing–based tools to map riparian vegetation composition and monitor vegetation condition over time. These tools enable accurate identification of tamarisk extent, detection of vegetation stress, and comparison with native species such as cottonwood and willow. This information directly supports restoration and management actions, including targeted tamarisk removal, protection of endangered species habitat, and prioritization of areas for native vegetation recovery. The tools also provide insight into how riparian vegetation responds to changing climate and hydrologic conditions, strengthening long-term planning for riparian forest management. Findings from this work demonstrate that riparian vegetation responses vary across river systems, indicating differences in plant composition and hydro-climatic conditions. Tamarisk on both the Gila and San Carlos Rivers generally exhibit greater declines in greenness in response to higher temperature as well as lower precipitation and river flow, while cottonwood ( Populus fremontii ) and willow (Salix spp.) are particularly sensitive to changes in discharge along the San Carlos River and respond more directly to both high and low flows, with more moderate responses to precipitation and temperature. By providing actionable, science-based information, this research supports climate adaptation planning, wildfire risk reduction, and improved riparian ecosystem health, with benefits that extend beyond the Reservation to regional water and wildlife conservation efforts.

Arizona, New Mexico↗
USGS2024

Thick- and thin-skinned contractional styles and the tectonic evolution of the northern Sangre de Cristo Mountains, Colorado, USA

The Sangre de Cristo Mountains of southern Colorado and northern New Mexico, USA, contain an unusual combination of thick- and thin-skinned contractional structures involving both basement and cover rocks in the Laramide Rocky Mountain foreland. These structures are truncated by down-faulted extensional basins to the east and west. Together with synorogenic sediments, these structures preserve a record of the rise of the Ancestral Rocky Mountains, the Laramide orogeny, and Rio Grande rifting. Laramide structures within the mountains provide clues to processes that link the three events and to necessary conditions for thin-skinned and thick-skinned contractional structures to form together in continental interiors. To examine the full variety of structural styles, a portion of the northern Sangre de Cristo fold- and-thrust belt in Colorado was described and interpreted using geologic maps and structural cross-sections. Stratigraphic relations of the Ancestral Rocky Mountain highlands and basin fill were reconstructed from existing maps. These relations allow identification of faults inherited from the Ancestral Rocky Mountains, differentiation of thrust sheets, and in some cases, estimation of the magnitude of displacement. To examine relations between Laramide thrusts and Rio Grande rifting, kinematic data were collected from a thrust fault adjacent to rift faults. Three thrust fault styles were recognized: thin-skinned basement, thin-skinned cover rocks, and thick-skinned basement. Thin-skinned thrusts arising from a hinterland beneath the present San Luis Valley carried sheets of Proterozoic basement rocks northeast over a Laramide foreland. These basement thrusts are interpreted to be faults of the Ancestral Rocky Mountains that reactivated during the Laramide orogeny. The Laramide foreland consists of thin-skinned thrusts and folds in sedimentary cover rocks as young as 49 Ma. Both thin-skinned thrusts in basement and cover rocks are bounded by thick-skinned basement thrusts that moved intermittently throughout the Laramide orogeny. We infer that thin-skinned thrusts form in continental interiors where deformation is focused in weak strata of thick basin fill and in fluid-reaction weakened preexisting faults in basement rocks. Both conditions are met in the Sangre de Cristo Mountains. Basement thrusts adjacent to the San Luis Valley contain evidence of plastic contractional microstructures overprinted by extensional microstructures that may record the transition from Laramide contraction to Rio Grande extension of the crust.

Colorado↗
USGS2024

StreamStats—A quarter century of delivering web-based geospatial and hydrologic information to the public, and lessons learned

StreamStats is a U.S. Geological Survey (USGS) web application that provides streamflow statistics, such as the 1-percent annual exceedance probability peak flow, the mean flow, and the 7-day, 10-year low flow, to the public through a map-based user interface. These statistics are used in many ways, such as in the design of roads, bridges, and other structures; in delineation of floodplains for land-use zoning and setting of insurance rates; for regulatory purposes, such as the permitting of wastewater discharges; and for hydrologic and climate change studies. StreamStats was first developed for Massachusetts and released in 2001. The application provided users with the ability to obtain streamflow statistics computed from data collected at USGS streamgages and to obtain estimates of streamflow statistics for user-selected ungaged sites. Massachusetts StreamStats used geographic information system software and digital mapping to compute drainage-basin characteristics, which were then used in statistical models to estimate streamflow statistics for the user-selected sites. The statistical models were in the form of equations that were developed through a process known as regression analysis. StreamStats was the first known web application with the ability to do interactive geoprocessing. The utility of Massachusetts StreamStats was instantly apparent, leading the USGS to develop a version of StreamStats that could be implemented nationally. USGS State offices normally were required to develop custom regression equations and prepare local digital mapping data needed for implementing StreamStats for their States. Funding needed to complete this work usually was provided through cooperative agreements between the USGS and State agencies. In 2004, Idaho became the first to be released in the national version of StreamStats. By 2023, 44 States were fully implemented and six were undergoing implementation. StreamStats has undergone many modifications over the years to keep up with changes to the underlying software and to add functionality. Customized functionality and separate linked StreamStats applications were developed for several States. Meeting the high demand for additions and improvements to StreamStats while also adhering to budgetary constraints has, at times, been challenging. The StreamStats development team has identified numerous additional improvements that could be made to provide better performance and more functionality. The lessons learned from the experience of building and operating StreamStats for nearly 25 years could be relevant to others interested in pursuing efforts of a similar scale.

Circular↗
USGS2025

A joint Gaussian process model of geochemistry, geophysics, and temperature for groundwater TDS in the San Ardo Oil Field, California, USA

Decline in availability of fresh groundwater has expanded interest in brackish groundwater resources; however, the distribution of brackish groundwater is poorly understood. Water resources in sedimentary basins across the United States often overlie oil and gas development. Mapping of groundwater total dissolved solids (TDS) using data from oil well geophysical logs has become an important technique for identifying fresh and brackish groundwater. Existing geophysical log analysis methods use porosity and temperature to relate formation resistivity to TDS. Typically, natural geothermal gradients are used to estimate temperature at the location of collected resistivity. However, in thermally enhanced oil fields, steam is injected into the subsurface to mobilize high viscosity oil, creating variable temperature distributions. Furthermore, TDS derived from resistivity also depends on the fractions of dominant ions. Typically, chloride and bicarbonate fractions must be determined. It is also necessary to model TDS across many geologic units with heterogenous porosity distributions. Collectively, each quantity used to estimate TDS (resistivity, porosity, temperature, bicarbonate fraction) varies in space and time, and available data points are rarely collocated. Here, we present a new method of mapping groundwater TDS that continuously models each quantity together with a joint Gaussian process. This method enables mapping fresh and brackish water with practically available data. We apply this method to the San Ardo Oil Field in Monterey County, California, where steam injection occurs. In some areas of the aquifer system overlying the oil zone, the temperature is ∼75 °C, roughly twice the natural background value. Groundwater TDS is typically <1,500 mg/L in the aquifer and increases with depth to ∼9,000 mg/L in the oil-producing zone. A low-permeability clay layer delineates the fresh and brackish water, likely by inhibiting surface recharge from penetrating the deeper zones, allowing higher-TDS connate water to remain in place. Weaker lateral TDS trends may be controlled by recharge patterns associated with the Salinas River. Our model reveals with high certainty that groundwater has freshened in one localized part of the oil-producing zone and suggests with less certainty that more widespread freshening has also occurred. The lowering of TDS was possibly from decades of low-TDS steam injection and the associated fluid production and disposal operations.

California↗
USGS2025

Collaborative drought science planning in the Colorado River Basin

The U.S. Geological Survey (USGS) is using collaborative, interdisciplinary planning to develop data and tools needed to optimize the management of water resources and land use by resource management agencies during an ongoing, multidecadal drought in the Colorado River Basin. The USGS Actionable and Strategic Integrated Science and Technology team works to build relationships with resource management agencies and other stakeholders who can benefit from the use of USGS data and products. In 2023, the Actionable and Strategic Integrated Science and Technology team hosted a series of collaborative workshops to bring together representatives of resource management agencies and other stakeholders (any person or entity with interests in a resource or location) with USGS program managers, scientists, and multidisciplinary subject matter experts to codevelop concepts for interdisciplinary drought science and technology projects to address pressing needs related to drought in the Colorado River Basin. Workshop participants identified current and recent scientific data that could be shared through a centralized online data portal. Workshop participants also identified drought science and technology needs and developed project concepts to address those science needs. Participants categorized project concepts based on their potential to develop short-, mid-, and long-term drought science data and tools, provide for the spatial or temporal expansion of ongoing USGS science projects, and address high-priority science needs. Participants developed nine project concepts: (1) understanding shifting ecohydrologic baselines, (2) San Juan River Basin synthesis, (3) incorporating dynamic land cover into hydrologic models, (4) aridification compared to drought, (5) surface water-groundwater interactions, (6) cascading effects of drought on dust, (7) cascading effects of drought on water availability, (8) cascading effects of drought on socioeconomic factors, and (9) the value of water in the Colorado River Basin. This report provides an overview of the 2023 Codesign Workshop Series, synthesized outcomes from workshop materials and discussions, and science project concepts that emerged from the collaborative meetings that will continue to be refined into science project proposals through codevelopment processes. This report also highlights lessons learned and next steps needed to receive feedback and testing of the USGS Science Collaboration Portal, continue collaboration to develop detailed specifics and steps for short-term wins, develop interdisciplinary project proposals, and implement science planning and studies.

Arizona, California, Colorado, Nevada, New Mexico,↗