Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Frontiers in Environmental Science”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,607 records · Page 49Linked to original sources
USGS1998

Continuous hydrologic simulation of runoff for the Middle Fork and South Fork of the Beargrass Creek basin in Jefferson County, Kentucky

The Hydrological Simulation Pro-gram-FORTRAN (HSPF) was applied to an urban drainage basin in Jefferson County, Ky to integrate the large amounts of information being collected on water quantity and quality into an analytical framework that could be used as a management and planning tool. Hydrologic response units were developed using geographic data and a K-means analysis to characterize important hydrologic and physical factors in the basin. The Hydrological Simulation Program FORTRAN Expert System (HSPEXP) was used to calibrate the model parameters for the Middle Fork Beargrass Creek Basin for 3 years (June 1, 1991, to May 31, 1994) of 5-minute streamflow and precipitation time series, and 3 years of hourly pan-evaporation time series. The calibrated model parameters were applied to the South Fork Beargrass Creek Basin for confirmation. The model confirmation results indicated that the model simulated the system within acceptable tolerances. The coefficient of determination and coefficient of model-fit efficiency between simulated and observed daily flows were 0.91 and 0.82, respectively, for model calibration and 0.88 and 0.77, respectively, for model confirmation. The model is most sensitive to estimates of the area of effective impervious land in the basin; the spatial distribution of rain-fall; and the lower-zone evapotranspiration, lower-zone nominal storage, and infiltration-capacity parameters during recession and low-flow periods. The error contribution from these sources varies with season and antecedent conditions.

Kentucky↗
USGS2025

Extremophile hotspots linked to containerized industrial waste dumping in a deep-sea basin

Decaying barrels on the seafloor linked to DDT contamination have raised concerns about the public health implications of decades old industrial waste dumped off the coast of Los Angeles. To explore their contents, we collected sediment cores perpendicular to five deep-sea barrels. The concentration of DDT and its breakdown products were highly elevated relative to control sites yet did not vary with distance from the barrels, suggesting that they were not associated with the contamination. Sediment cores collected through white halos surrounding three barrels were enriched in calcite and had elevated pH. The associated microbial communities were low diversity and dominated by alkalophilic bacteria with metagenome-assembled genomes adapted to high pH. A solid concretion sampled between a white halo and barrel was composed of brucite, a magnesium hydroxide mineral that forms at high pH. Based on these findings, we postulate that leakage of containerized alkaline waste triggered the formation of mineral concretions that are slowly dissolving and raising the pH of the surrounding sediment pore water. This selects for taxa adapted to extreme alkalinity and drives the precipitation of “anthropogenic” carbonates forming white halos, which serve as a visual identifier of barrels that contained alkaline waste. Remarkably, containerized alkaline waste discarded >50 years ago represents a persistent pollutant creating localized mineral formations and microbial communities that resemble those observed at some hydrothermal systems. These formations were observed at one-third of the visually identified barrels in the San Pedro Basin and have unforeseen, long-term consequences for benthic communities in the region.

California↗
USGS2024

Geophysical characterization of mine influenced groundwater and surface water in the Mayflower section of the Animas River, Bonita Peak Mining District, Silverton Colorado

This report details findings from geophysical investigations to identify possible groundwater - surface water interactions near the Mayflower Section of the Animas River in Silverton, Colorado. The Mayflower Section is a mine influenced Superfund Site in Colorado. This investigation utilized electromagnetic induction (EM or EMI), magnetic, and fiber optic distributed temperature system (FODTS) geophysical methods to measure the bulk earth electrical conductivity, magnetic susceptibility, and temperature of specific surveyed volumes of the earth near the Mayflower Section of the Animas River. These physical parameters are used to understand the groundwater – surface water interactions, which can guide decision makers in their assessment of mine-impacted surface water. This report details the results from characterization and monitoring technologies to provide high data density and continuous monitoring of bulk earth electrical conductivity and temperature in the Mayflower section of the Animas River to identify zones of groundwater – surface water interactions and potential metal loading from mine influenced water. The investigation separated right and left bank characterization for each method and indicates more groundwater is entering from the right bank than the left bank and these predominantly right bank discharges potentially contain metal-rich water compared to the left bank. Results also indicate mineral veins facilitate preferential groundwater discharge to the river due to possible jointing, fractures, and permeability differences sometimes occurring along veins relative to host rock. For example, Boulder Gulch is likely groundwater dominated and may be receive water impacted by Mayflower Impoundments #1 and #2. Additionally, the beaver ponds near Blair Gulch may influence groundwater discharge and Mayflower Impoundment #4 is possibly impacting groundwater and surface water and may be connected to the wetlands to the west of the impoundment. These data could be further analyzed for smaller spatial scale analysis within areas of interest. The identification of these locations along sections of the river likely impacted by mine influenced groundwater potentially entering the Animas River and can be used by site investigators, decision makers, and stakeholders in mitigation decisions and strategies.

Colorado↗
USGS2024

Framework for implementing damping scaling factors in U.S. Geological Survey National Seismic Hazard Models

Traditionally, probabilistic seismic hazard analysis (PSHA) has focused on calculating ground motion hazard curves for elastic, 5%-damped pseudo spectral accelerations, Sa(T,5%), which are used as the basis for engineering design parameters and targets for ground motion selection and modification. However, structures and geotechnical systems can exhibit a wide range of damping ratios both above and below the 5% level, depending on the construction material, structural system, nonstructural elements, or subsurface soil properties. When spectral parameters at such damping levels are required for certain applications, 5%-damped accelerations have traditionally been extracted from PSHA-based hazard curves and adjusted outside of the hazard integral using damping scaling factors (DSF) such as those from Newmark & Hall (1982). Recent advances in the development of more rigorous and comprehensive damping scaling models (e.g., Rezaeian et al., 2014; Rezaeian et al., 2021) have allowed for the modeling of means and standard deviations of DSFs as functions of earthquake source and path properties for crustal, intraslab, and subduction interface tectonic environments. These DSF models can be applied to ground motion model (GMM) estimates of Sa(T,5%) for a given earthquake rupture scenario to produce a corresponding mean and standard deviation Sa at a specified damping ratio β, Sa(T,β). In this study, the DSF models of Rezaeian et al. (2014) and Rezaeian et al. (2021) are implemented within the U.S. Geological Survey National Seismic Hazard Model (NSHM) PSHA framework to calculate probabilistic hazard curves for spectral accelerations at damping ratios from 0.5% to 30%. The DSF models are applied directly to the mean and standard deviation of Sa(T,5%) predictions from each GMM in the NSHM logic tree. Resulting hazard curves and uniform hazard and risk spectra for Sa(T,β) are presented for several geographic locations and compared with corresponding spectra estimated using current design practices by applying the same DSFs outside of the PSHA calculation. Key differences between the two methods for estimating Sa(T,β) are discussed, and potential strategies are presented for the implementation and usage of the hazard-consistent Sa(T,β) in building codes. Comparing the results to those from DSFs used in current design practices that are mainly based on Newmark & Hall (1982) is not explored in this study.

Conference Paper↗
USGS2024

Forecasting storm-induced coastal flooding for 21st century sea-level rise scenarios in the Hawaiian, Mariana, and American Samoan Islands

Oceanographic, coastal engineering, ecologic, and geospatial data and tools were combined to evaluate the increased risks of storm-induced coastal flooding in the populated Hawaiian, Mariana, and American Samoan Islands as a result of climate change and sea-level rise. We followed a hybrid (dynamical and statistical) downscaling approach to map flooding due to waves and storm surge at 10-square meter resolution along all 1,870 kilometers of these islands’ coastlines for annual (1-year), 20-year, and 100-year return-interval storm events and +0.00 meter (m), +0.25 m, +0.50 m, +1.00 m, +1.50 m, +2.00 m, and +3.00 m sea-level rise scenarios. We quantified the coastal flood depths and extents using the latest climate forcing from Intergovernmental Panel for Climate Change’s Sixth Assessment Report Coupled Model Intercomparison Project. The data generated using these methods provide stakeholders and decision makers with a spatially explicit, rigorous valuation of how, where, and when climate change and sea-level rise increase coastal storm-induced flooding to help identify areas where management and (or) restoration could potentially help reduce the risk to, and increase the resiliency of, the coastal communities in the populated Hawaiian, Mariana, and American Samoan Islands.

Hawaii↗
USGS2025

Using the D-Claw software package to model lahars in the Middle Fork Nooksack River drainage and beyond, Mount Baker, Washington

Lahars, or volcanic mudflows, are the most hazardous eruption-related phenomena that will affect communities living along rivers that originate on Mount Baker. In the past 15,000 years, the largest lahars from Mount Baker have affected the Middle Fork Nooksack River drainage and beyond. Here we use the physics-based D-Claw software package to model nine lahar scenarios that are initiated as water-saturated landslides between Sherman Crater and the Roman Wall on the Mount Baker edifice and flow down the Middle Fork Nooksack River. The scenarios range in volume from 1 to 260 million cubic meters and have an initial hydraulic permeability from 10 −12 to 10 −10 meters squared. Model output includes data such as flow depth, velocity, runout distance, area inundated, arrival time, and sediment concentration as well as information that allows scientists to calculate other important hydrologic characteristics such as lahar discharge. These data are important to officials who have the responsibility to plan for, or take mitigation measures against, future Mount Baker lahars. To check the validity of the D-Claw results, we compare the scenarios to known geologic information. We also compare D-Claw results with empirical models that have been used in the past to determine potential inundation areas, runout distances, and arrival times. These comparisons highlight similarities and differences between empirical and physics-based models. We also present D-Claw scenario-based animations to help scientists, officials, and lay people alike to visualize how future lahars could affect communities.

Washington↗
USGS1973

Geohydrology of the Cross-Florida Barge Canal area, with special reference to the Ocala vicinity

The Cross-Florida Barge Canal route commences at Palatka on the St. Johns River, about 75 miles upstream from the Atlantic Ocean, and extends 110 miles southwestward across Peninsular Florida into deep water in the Gulf of Mexico near Yankeetown. The canal will be equipped with five locks, each 600 feet long and 84 feet wide, and the channel will be a minimum of 12 feet deep and 150 feet wide. From near Ocala northeastward, the canal channel will replace much of the natural channel of the Oklawaha River, and will be excavated into beds of the so-called shallow sand aquifer of Miocene age and younger, which overlies limestone of the Floridan aquifer. Westward from Ocala, most of the canal will be excavated below the potentiometric surface into limestone and dolomite of the Floridan aquifer. Water levels of Rodman, Eureka, and Inglis Pools will be controlled by dams and spillways with the limited exchange of water between the pools and the aquifers. The water levels in the Summit Pools will fluctuate with the natural changes in the ground-water level of the Floridan aquifer, although the stage of the pool will be controlled partly by the stage held in the Eureka Pool. A dynamic inflow-outflow relationship will exist between the Summit Pool and the Floridan aquifer. The Floridan aquifer in the canal area is 1,000 to 1,200 feet thick and consists of limestone and dolomite of middle Eocene Miocene age, including from older to younger, the Lake City, Avon Park, and Ocala limestones plus permeable sandy, dolomitic limestone in the lower part of the Hawthorn Formation. It is possible that most of the flow to the two major springs in the area occurs in the upper 100 feet or so of the aquifer in the Ocala Limestone. The aquifer is underlain by the Oldsmar limestone of early Eocene age and is overlain by sand, clayey sand, clay and shell beds of Miocene through Holocene age, in thickness from a few feet to 300 feet. The permeable beds overlying the Floridan aquifer constitute the shallow aquifer, while the poorly permeable ones act as confining beds where the Floridan aquifer is under artesian conditions. A north-south line drawn separating the head of Silver Springs on the west from the Oklawaha River on the east marks the approximate western limit of a continuous blanket of materials of Miocene-Pliocene(?) age covering the rocks of the Floridan aquifer. East of the line, much of the aquifer is under artesian conditions, particularly in the Oklawaha River valley, although in some areas east of the valley, direct recharge through thick permeable Miocene-Pliocene(?) sands occurs. West of the line, only scattered remnants of a once continuous Miocene-Pliocene(?) cover remain. Lack of the cover is a result of erosion on the crest and flank of the Ocala Uplift, a broad northwest-southeast trending anticlinal upwarp, the axis of which is crossed by the canal route in the Dunnellon area. Over most of this area the Floridan aquifer is unconfined and receives direct recharge through a cover of a few tens of feet of sand and clayey sand of Quaternary age. Tensional stresses during the structural evolution of the Ocala Uplift produced an intersecting system of fractures and normal faults in rocks of the Floridan aquifer. The fractures and faults are important controls for orientation of solution channels and, therefore, for development of ground-water circulation patterns. When the system surface streams, which once drained the Barge Canal area, eroded the poorly permeable Miocene-Pliocene(?) cover from the flanks of the Ocala Uplift, surface runoff was reduced and precipitation began to directly infiltrate the underlying limestones. Now only principal streams remain, such as the Oklawaha and Withlacoochee Rivers and a few short tributaries, while one of the most highly developed subsurface drainage systems in the world has evolved in cavernous limestone of the Floridan aquifer. Two of the larger freshwater springs in the world now discharge from the Floridan aquifer in the canal area. Silver Springs near Ocala discharges an average 531 mgd (million gallons per day) down the 4-mile long Silver River, which flows on poorly permeable beds to the Oklawaha River. Rainbow Springs near Dunnellon discharges on average 468 mgd from numerous orifices in the bed of the 5-mile-long Rainbow River, which flows into the Withlacoochee River. The heads of the springs have migrated to their present positions partly because of a tendency of ground-water levels to decline as permeability in the aquifer is increased due to removal of limestone by solution, and because of mechanical erosion of the limestone in the vicinity of the spring heads. Also, points of principal spring discharges have shifted in the past due to changes in ground-water levels in response to changes in sea level. The subsurface drainage system is continuing to evolve today, as evidenced in part by frequent occurrence of new sinkholes and by the presence of significant amounts of calcium bicarbonate in the spring waters. Rodman Pool, at the east end of the canal, is separated from the Floridan aquifer by poorly permeable materials. The pool's operating water level will be only a few feet above the potentiometric surface at the downstream end, and at or slightly below the potentiometric surface at the upstream end. Little exchange of water between the Rodman Pool and the Floridan aquifer is expected. Eureka Pool, just upstream from Rodman Pool, will also be separated from the Floridan aquifer by poorly permeable beds. However, the stage of the pool will be about 15 feet higher than the natural potentiometric surface at the pool's downstream end, and some seepage into the Floridan aquifer is anticipated through faults and leaky parts of the poorly permeable beds, with a consequent rise in ground-water levels in areas adjacent to the lower end of the pool. Possibilities for particulate contamination of the aquifer will tend to be minimized because of the filtering capacity of the materials through which water must pass to reach the aquifer, although the natural filter will not preclude movement into the aquifer of contaminants which might become dissolved in the pool waters. No significant interchange of water between the pool and the aquifer is expected at the upstream end of the Eureka Pool. Present construction plans indicate an operating stage for Eureka Pool which will range between 38 and 40 feet above mean sea level, although it is possible to dredge the pool deep enough to permit a range in stage of 36 to 40 feet. A backwater effect extending up Silver River from the Eureka Pool is expected to regulate the stage at the head of Silver Springs between 39 and 44 feet above mean sea level if the pool ranges between 36 and 40 feet. If Eureka Pool ranges only between 38 and 40 feet, the range of stage at the head of the springs should be about 41 to 44 feet above mean sea level. From Inglis Lock west, the canal will have direct connection with the Gulf, and canal stage will fluctuate with the Gulf tide. Since the canal stage will be slightly lower than the adjacent ground-water levels along much of the reach, there will be some ground-water inflow to the canal. No significant changes in the existing ground-water regime are expected in the vicinity of Inglis Pool, the first step up in the canal east of the Gulf. Existing ground-water and surface-water levels in the area will not change appreciable, and the natural stage and flow of Rainbow Springs, which will flow by way of Rainbow River into Inglis Pool, should not be affected by canal operations. A possible adverse effect of the canal on the Inglis Pool area could result if sea water is locked up from the Gulf through Inglis Lock. However, the high step of 25 feet at the lock, flushing action of continuous flow from Inglis Pool to the lower reaches of the Withlacoochee River, and use of possible preventive locking procedures should minimize the problem. The potential for adverse effects on the ground-water regime is greatest in the area of the Summit Pool. Through most of the length of the pool, the canal channel will be excavated into limestone of the Floridan aquifer to depths of 12 to 27 feet below the potentiometric surface. Changes that will take place in the ground-water flow system in the Silver Springs drainage area, once the canal is completed, were estimated by flow-net analysis. Variation in aquifer transmissivity was determined by calculating transmissivity in 25 different flow cells surrounding Silver Springs. Transmissivity in the 25 cells averages about 15,600,000 gpd/ft [2,090,000 ft2/day (feet squared)], but transmissivity in the six cells through which the Summit Pool passes ranges from 9,000,000 to 44,000,000 gpd/ft (1,210,000 to 5,900,000 ft2/day). Transmissivity was used to compute static stage of the Summit Pool under given ground-water level conditions. Had the canal existed in May 1968 and had the stage of Eureka Pool been held at 36 feet at the time, the static stage in Summit Pool would have been about 42.1 feet above mean sea level. Thus, a conceptual model of the changes in the potentiometric surface wrought by the finished canal was drawn, and zones of ground-water inflow and outflow were delineated. Most outflow from the Summit Pool to the aquifer should be limited to one 4-mile-long zone along the north side of the pool, about 5 miles south of Silver Springs. It is estimated that a water volume equivalent to about 8 percent of the daily flow of Silver Springs will enter the Summit Pool each day from the southern one-third of the Silver Springs drainage area. A like amount will reenter the aquifer at the main zone of outflow and move toward Silver Springs at an estimated average velocity of about 200 feet per day, if something close to the natural static stage of the pool is maintained by return pumpage of the lockage losses. At a velocity of 200 feet per day, water from the Summit Pool would discharge at Silver Springs about 140 days later. However, any estimate of velocity in the highly cavernous limestone aquifer in the area should be used with caution, because difficult to measure changes in porosity and thickness of major zones of flow may cause large variations in velocity. If all lockage losses are returned to the Summit Pool by pumping from Eureka Pool, no net loss from the Silver Springs drainage area, except for some evaporation from the water surface in the canal and possible leakage around locks, will result from canal operations. The zone of outflow from the Summit Pool to the aquifer will be in a natural potentiometric trough, and the zone of inflow will be in a potentiometric ridge area. The equilibrium water level in the pool will tend to be about 1 foot higher than the altitude of the lowest level in the pre-canal potentiometric trough, and about 2 feet lower than the highest level on the pre-canal potentiometric ridge. West of the Silver Springs drainage area just east of Dunnellon Lock, in the area of a local potentiometric high, the water level in the Summit Pool is expected to be about 15 feet below the natural potentiometric surface. In most areas 2 to 3 miles away from the Summit Pool, effects of the canal on the natural potentiometric surface should be slight. The stage of the Summit Pool, judging from the 36-year record for ground-water level changes and the anticipated indirect effect of the controlled stage in Eureka Pool, should have a maximum of about 10.5 feet with a maximum water level of about 51.5 feet above mean sea level and a minimum of about 41.0 feet above mean sea level. Of particular importance in the Summit Pool is an implementation of well planned construction and operational procedures designed to minimize risks of ground-water contamination.

Florida↗
USGS2026

Complex carbonate ore mineralogy in the Mountain Pass carbonatite rare earth element deposit, USA

Economic concentrations of rare earth element (REE) minerals are uncommon in the Earth’s crust, with most occurring in carbonatites. Unlike most igneous rocks composed of silicate minerals, carbonatites are dominated by carbonate minerals, some of which can incorporate significant light REEs (LREEs; La, Ce, Pr, Nd). Technological applications of REEs are numerous and they have been identified as some of the most critical mineral commodities to the global economy. The Mountain Pass carbonatite stock in the Mojave Desert of California is the most economically significant REE deposit in the USA and contains a few to tens of percent (by volume) of the carbonate REE ore mineral bastnäsite. Despite the economic significance of the Mountain Pass deposit, studies of its ore mineralogy are limited. Here we present new carbonate ore mineralogy data for a compositionally diverse suite of carbonatitic rocks from the Mountain Pass stock and related dikes. Whole-rock geochemical data are integrated with mineral-scale textural and chemical data obtained by scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and microRaman spectroscopy. Our results document a complex spectrum of REE-bearing carbonate minerals and intermediate mixed-layer structures. Mineral species include bastnäsite [REE(CO 3 )F], hydroxylbastnäsite [REE(CO 3 )OH], parisite [Ca(REE) 2 (CO 3 ) 3 F 2 ], synchysite [Ca(REE)(CO 3 ) 2 F], röntgenite [Ca 2 (Ce,La) 3 (CO 3 ) 5 F 3 ], and sahamalite [(Mg,Fe 2+ )(REE) 2 (CO 3 ) 4 ]. Carbonate ore mineralogy is heterogeneous within and between samples, including at the intracrystal scale. Complexly zoned crystals exhibit as many as five to six different compositional domains and syntaxial intergrowths, commonly with the more Ca-rich varieties (parisite, synchysite) forming crystal rims that surround relict bastnäsite cores. We attribute the phenocryst variability to changes in the chemistry and temperature of primary carbonatite magmas and evolved/exsolved fluids. Cross-cutting vein textures of calcite, celestine and various REE carbonate minerals, interstitial bastnäsite crystallization, breccia blocks lined by fine-grained bastnäsite, and the presence of hydroxylbastnäsite and partially hydroxylated bastnäsite point to the role of secondary hydrothermal processes in REE mineralization. Fluorcarbonate mineral compositions demonstrate that La and Ce are more structurally abundant in bastnäsite, whereas the more Ca-rich species (parisite, synchysite) contain a greater proportion of REE heavier than Pr (Nd, Sm, Eu, Gd) and Y. Atomic ratios of Pr/(Nd + Pr) are likewise variable, with the highest average value for bastnäsite (0.25) compared to parisite (0.22) and sychysite (0.21). This finding has geometallurgical implications, given that current mining operations are focused on recovery of Nd and Pr for high field strength permanent magnets and the Nd/Pr ratios are a critical factor in ore processing and magnet manufacture.

California↗
USGS2025

Assessing flood water infiltration and storage in a restored floodplain

In urban areas, floodplain restoration is gaining prominence as a strategy for restoring the natural functions of floodplain ecosystems and reducing flood risk. This has spurred research into potential interactions between floodwaters, the hyporheic zone, and the floodplain aquifer. An urban restored stream in Wisconsin, USA, was used as a case study to examine four methods to estimate floodplain infiltration and storage during overbank floods. We characterised flood-related infiltration over a 4-year period from 2018 through 2021 by simultaneously and continuously measuring groundwater levels and vertical temperature profiles with stream water levels linked to high-resolution flood inundation maps. High-resolution topographic data helped to quantify surface floodplain storage and the unsaturated soil volume relative to flood stage. Infiltration estimates from the simple methods align well with those from the more complex methods; however, the complex methods provide additional insights about the factors influencing infiltration. Results from all methods indicate that the volume of water that vertically infiltrates during floods is likely small relative to the total volume of the flood, with 0.08%–0.52% of flood water infiltrating into the floodplain, on average. Spatially variable vertical hydraulic gradients, driven by flood depth, groundwater level, and permeability, imply heterogeneous patterns of infiltration across the floodplain. Gradients favourable for infiltration typically occurred during the onset of flooding but, over the study period, were mostly (98% of the time) favourable for groundwater discharge to the channel (non-flood periods). These findings highlight the importance of considering surface-groundwater dynamics, floodplain soils, and unsaturated floodplain volume in defining the benefits of floodplain infiltration for flood attenuation.

Wisconsin↗
USGS1996

Hydrogeologic investigation and simulation of ground-water flow in the Upper Floridan Aquifer of north-central Florida and southwestern Georgia and delineation of contributing areas for selected city of Tallahassee, Florida, water-supply wells

A 4-year investigation of the Upper Floridan aquifer and ground-water flow system in Leon County, Florida, and surrounding counties of north-central Florida and southwestern Georgia began in 1990. The purpose of the investigation was to describe the ground-water flow system and to delineate the contributing areas to selected City of Tallahassee, Florida, water-supply wells. The investigation was prompted by the detection of low levels of tetrachloroethylene in ground-water samples collected from several of the city's water-supply wells. Hydrologic data and previous studies indicate that; ground-water flow within the Upper Floridan aquifer can be considered steady-state; the Upper Floridan aquifer is a single water-bearing unit; recharge is from precipitation; and that discharge occurs as spring flow, leakage to rivers, leakage to the Gulf of Mexico, and pumpage. Measured transmissivities of the aquifer ranged from 1,300 ft 2 /d (feet squared per day) to 1,300,000 ft2/d. Steady-state ground-water flow in the Upper Floridan aquifer was simulated using a three-dimensional ground- water flow model. Transmissivities ranging from less than 5,000 ft2/d to greater than 11,000,000 ft 2 /d were required to calibrate to observed conditions. Recharge rates used in the model ranged from 18.0 inches per year in areas where the aquifer was unconfined to less than 2 inches per year in broad areas where the aquifer was confined. Contributing areas to five Tallahassee water-supply wells were simulated by particle- tracking techniques. Particles were seeded in model cells containing pumping wells then tracked backwards in time toward recharge areas. The contributing area for each well was simulated twice, once assuming a porosity of 25 percent and once assuming a porosity of 5 percent. A porosity of 25 percent is considered a reasonable average value for the Upper Floridan aquifer; the 5 percent porosity simulated the movement of ground-water through only solution-enhanced bedding plains and fractures. The contributing areas were generally elliptical in shape, reflecting the influence of the sloping potentiometric surface. The contributing areas delineated for a 5 percent porosity were always much larger than those determined using a 25 percent porosity. The lowest average ground-water velocity computed within a contributing area, using a 25 percent porosity, was 1.0 ft/d (foot per day) and the highest velocity was 1.6 ft/d. The lowest average ground-water velocity, determined using a 5 percent porosity, was 2.4 ft/d and the highest was 7.4 ft/d. The contributing areas for each of the five wells was also determined analytically and compared to the model-derived areas. The upgradient width of the simulated contributing areas were larger than the upgradient width of the analytically determined contributing areas for four of the five wells. The model could more accurately delineate contributing areas because of the ability to simulate wells as partially penetrating and by incorporating complex, three-dimensional aquifer characteristics, which the analytical method could not.

Florida, Georgia↗
USGS2025

Site response and wave propagation effects in the eastern United States

Fourier amplitude spectra from regional earthquakes in the eastern United States are used in a parametric inversion for source, path, and site effects. Five earthquakes are selected for analysis during the installation of the United States National Seismic Network (US), Earthscope’s USArray Transportable Array (TA), and other temporary arrays to maximize station coverage. A global search algorithm is used to solve for site response from 0.1 to 15 Hz, corner frequency, geometrical spreading ( r - γ ), and frequency dependent anelastic attenuation in the form Q(f) = Q o f α . Tradeoff between moment and geometric spreading is handled by fixing the moment. The tradeoff between corner frequency and Q(f) is solved by selecting the value of corner frequency that minimizes an objective function defined over all stations. Values of site response and attenuation parameters show a strong spatial correlation with the physiographic provinces of the eastern United States. Site response for the Atlantic Coastal Plain is consistent with previous work using spectral ratios relative to a reference site, defined by strong resonance peaks correlated with the thickness of sediments. Site response for the other physiographic provinces is markedly different from the coastal plain, with a lack of distinct resonance peaks and a broad moderate high at frequences from 0.1 to 0.5 Hz consistent with the hard-rock geology of the regions. Like site response, Q(f) has a strong correlation with physiographic province, showing lower values on the coastal plain and higher values inland. Geometric spreading exponent, γ, decreases with increasing hypocenter distance from just above 1 at a few tens of kilometers to 0.9 at 500 km. The limited range in geometric spreading values is attributed to starting the Fourier transform window at the S ‐wave arrival for all distances and averaging over multiple wave types.

eastern United States↗
USGS2024

Afterslip and creep in the rate-dependent framework: Joint inversion of borehole strain and GNSS displacements for the Mw 7.1 Ridgecrest earthquake

The elusive transition toward afterslip following an earthquake is challenging to capture with typical data resolution limits. A dense geodetic network recorded the Mw 7.1 Ridgecrest earthquake, including 16 Global Navigation Satellite System (GNSS) stations and 3 borehole strainmeters (BSM). The sub-nanostrain precision and sub-second sampling rate of BSMs bridges a gap between conventional seismologic and geodetic methods, exemplified by atypical postseismic shear strain reversals observed at nearfield (<2 km) station B921 that remain unexplained. We jointly invert GNSS displacements and BSM strains for coseismic and postseismic slip spanning hours to months over 7 independent periods. Cosiesmically, our model resolves the largest slip magnitudes of up to 6.6 m on the mainshock rupture plane, with similar patterns to other inferred slip distributions. The foreshock fault appears to slip coincidently with mainshock, revealing potential asperities activated during the preceding Mw 6.4 event. Postseismically, the best-fitting models adhere to mechanical rate-and-state expectations of logarithmically decaying slip adjacent to the coseismic rupture terminus, and where deep rheologic conditions favor creep. Most spatial variation occurs in the early postseismic timeframe (<1–2 weeks), with evidence for regional rheologic control and static stress dependence. Triggered creep on the neighboring Garlock Fault unexpectedly persists for >178 days—further highlighting the importance of fault networks in postseismic stress redistribution, critical to assessing future hazard.

Journal of Geophysics Research↗
USGS2025

Timing of hydrothermal alteration and Au-Sb-W mineralization, Stibnite-Yellow Pine district, Idaho

The Stibnite-Yellow Pine district of central Idaho was mined from the early 1900s until the 1990s, extracting gold, antimony, tungsten, and mercury from veins and disseminated and replacement ores in mountainous terrain along the headwaters of the Salmon River. Mining during the two World Wars supplied critical antimony and tungsten to the war efforts. Recent exploration has delineated mineral resources of over 187 metric tons Au, 274 metric tons Ag, and 93,000 metric tons Sb. Mineralization is hosted in Cretaceous Idaho batholith granitic rocks and a sequence of Neoproterozoic to Paleozoic metasedimentary strata of carbonate and siliciclastic compositions. Historical studies outlined some of the complex paragenesis but debated the absolute age of mineralization. New petrographic and geochronologic work documents a sequence of five hydrothermal events in the Stibnite-Yellow Pine district. Event 1 is related to Cretaceous magmatic and hydrothermal activity and includes events ranging in age from 86 to 75 Ma, including sparse quartz-molybdenite veins dated at 86 Ma. Disseminated gold mineralization of event 2 is associated with sericitic alteration and sulfidation of igneous biotite and replacement of plagioclase by potassium feldspar, largely in granodiorite. Gold is present in zoned arsenian pyrite in both disseminated ores and in crosscutting carbonate-quartz veins containing pyrite and arsenopyrite. The large Yellow Pine deposit, localized at a dilatant bend in the Meadow Creek fault, hosts such disseminated and vein gold. Event 2 is interpreted as the major gold-forming event; 40 Ar/ 39 Ar ages of sericite and potassium feldspar alteration range, respectively, from 70 to 59 and 66 to 56 Ma. The long span is interpreted to reflect the age of gold mineralization and local overprinting by event 3. A narrower range from 66 to 61 Ma is interpreted to date the peak of gold mineralization and alteration. Event 3, tungsten mineralization with scheelite, is texturally later than event 2 gold and localized along the Meadow Creek structure. Event 3 scheelite has been dated by isotope dilution-thermal ionization mass spectrometry (ID-TIMS) and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) U-Pb methods at 57 Ma. Event 4, best developed in the West End area, includes gold-silver–bearing quartz-carbonate-pyrite veins and breccias with epithermal textures and potassium feldspar alteration envelopes. Adularia from event 4 yields 40 Ar/ 39 Ar plateau ages of 52 to 51 Ma. Event 5 antimony and mercury mineralization consists of stibnite veins and breccia cements at the Yellow Pine and Hangar Flat deposits as well as cinnabar veins and replacements at the peripheral Fern and Hermes deposits; it is constrained by an LA-ICP-MS U-Pb date on scheelite (ca. 47 Ma) intergrown with stibnite. Minor propylitic and argillic alteration is evident in 47 Ma igneous dikes, which do not contain economic mineralization. The Au-Sb-W ores in the Stibnite-Yellow Pine mining district formed over an extended time period from about 70 to 45 Ma in multiple pulses that were localized along the Meadow Creek fault zone. Each event corresponds to episodes of magmatism and/or hydrothermal activity in the region. Insignificant event 1 skarn and molybdenum mineralization is similar in age to the Thompson Creek porphyry molybdenum deposit in central Idaho. Event 2 gold mineralization occurred during a magmatic gap in central Idaho but was synchronous with magmatism in the Bitterroot lobe further north; event 2 is similar in age to orogenic gold-arsenic mineralization at the Beartrack mine in eastern Idaho. Event 3 scheelite mineralization coincides with tungsten mineralization at the Quartz Creek deposit, late magmatism in the Bitterroot lobe, and rapid exhumation of the Atlanta lobe of the Idaho batholith. Event 4 gold mineralization is coincident with the onset of regional Challis magmatism and extension. Event 5 antimony and mercury mineralization is time-equivalent to epithermal gold mineralization in the nearby Thunder Mountain volcanic field and the peak of Challis magmatism.

Idaho↗
USGS2026

Top-down targeted network analysis of critical mineral commodities applied to international geochemistry database

The global demand for critical mineral commodities is rapidly increasing, making domestic production an important factor in supporting the economy and national security. Large scale, publicly available geochemical databases allow for the application of data informatics methods to interrogate critical mineral commodities data for correlations in deposit formation and distribution, particularly for identifying enrichment of multiple critical mineral commodities at the same deposit. In this study, we applied network analysis to the Critical Minerals Mapping Initiative (CMMI) ore geochemistry (Critical Minerals in Ores, CMiO) database to identify the high concentration (defined as 10× bulk crustal abundance) co-occurrence of different critical mineral commodities across a mineral system hierarchy from deposit environments to individual deposits. Identifying patterns or unique outliers in enrichment in network communities will allow for the location of secondary critical mineral commodity resources from under-utilized deposits. We find trends in the enrichment of critical mineral commodities in network-communities between the elements praseodymium (Pr), neodymium (Nd), terbium (Tb), and dysprosium (Dy) across multiple CMiO database deposit environments and groups down to specific deposit types and sites. A separate trend in network community deposition is observed as well between iridium (Ir) and platinum (Pt) in deposit environments, groups, types, and sites. Network analysis focused on critical minerals in magmatic-hydrothermal deposits identified multiple deposit sites from different deposit types within the CMiO database with concentrations of Dy, Nd, Tb, Pr, Ir, and Pt that are at least ten times greater than the crustal average. This approach can be applied to any target element(s) or deposit(s) of interest, allowing broad investigation of co-enriched critical mineral commodities.

Journal of Geochemical Exploration↗
USGS2026

Surface variable‐based machine learning for scalable arsenic prediction in undersampled areas

In the United States, private wells are not federally regulated, and many households do not test for Arsenic (As). Chronic exposure is linked with multiple health outcomes, and risk can change sharply over short distances and with well depth. Coarse maps or sparse sampling often miss exceedances. Most existing models operate at ∼1 km resolution and use groundwater chemistry or detailed geologic logs, which limits their use in undersampled areas where improved guidance is most needed. We overcome these limitations by developing a machine learning model for Minnesota, USA, that predicts As exposure risk using only surficial variables from remote sensing and global data sets. Variables related to surface water hydrology and geomorphology are selected based on mechanistic links that control redox conditions and As mobilization. Local training was essential, and surficial geology variables that are more sensitive to local conditions were needed to maximize model accuracy. The resulting complete model was sufficiently sensitive to generate accurate and detailed risk maps and depth profiles of As concentrations above the 10 μg/L maximum contaminant level. Accuracy depended on local training data density. We identified a training data density of 0.07 wells/km 2 as a practical target for stable county-level performance. Maps of exceedance probabilities highlight priority areas for testing that are particularly important in rural communities that have received less sampling. These results support public health action by guiding where to install wells and where to test them, how much new sampling is needed, and where treatment outreach is most urgent.

Minnesota↗
USGS2026

Modeling future groundwater depletion to evaluate sustainability goals set under the Sustainable Groundwater Management Act in the critically overdrafted basins of the Central Valley, California, USA (2020–2070)

In 2014, California's Sustainable Groundwater Management Act (SGMA) mandated local agencies to devise and implement groundwater sustainability plans to address critically overdrafted conditions throughout the state's aquifers. However, the feasibility of these agencies' sustainability goals has not previously been assessed through a regional-scale, integrative lens. Here, we develop and analyze a novel, basin-wide database of 936 sustainability indicator wells located within Central Valley subbasins designated as critically overdrafted, most of which lie in the San Joaquin Valley. Our database shows 2040 groundwater elevation goals vary widely from 60 m above to 80 m below 2020 levels, with variability within and between adjacent subbasins. To evaluate the feasibility of achieving these goals, we coupled the database with a regional hydrologic model (Central Valley Hydrologic Model version 2) and simulated multiple future pumping scenarios. Results show that under increased groundwater demand, 60%–70% of indicator wells may fail to meet their 2040 goals. Even a 50% reduction from 2020 demand levels leaves nearly 40% of wells failing to meet their sustainability thresholds by 2040. Baseline models show that by 2070, up to 70% of wells could fail to meet their goals due to large-scale, spatially connected regions of groundwater depletion. This integrated framework, linking the first region-wide compilation of SGMA indicator wells with a regional groundwater model, demonstrates that many local sustainability goals may be unattainable with substantial (up to 50%) reductions in pumping. Additional management interventions, such as expanded recharge or coordinated demand reductions, may help achieve sustainability goals.

California↗
USGS2026

Geochemical geodatabase of sedimentary strata (coal, coal-adjacent rocks, tuffaceous oil shale, phosphate-rich rocks) and produced water in the Uinta region, Utah and Colorado

The Geochemical Geodatabase of Sedimentary Strata (Coal, Coal-adjacent Rocks, Tuffaceous Oil Shale, Phosphate-rich Rocks) and Produced Water in the Uinta Region, Utah and Colorado, consists of compiled datasets acquired as part of the Carbon Ore, Rare Earth, and Critical Mineral (CORE-CM) Uinta Region assessment funded by the U.S. Department of Energy (DEFE0032046, 2021–2024; Birgenheier et al., 2024). The CORE-CM assessment focused on providing comprehensive geological and geochemical characterization of current and prospective sedimentary-hosted resources including coal, oil shale, phosphatic limestone, and produced water from oil and gas targets present in eastern Utah and northwestern Colorado (Figure 1). This Data Series includes a geodatabase that consists of analytical geochemical data collected September 2021 through December 2024 via portable X-ray fluorescence (pXRF), and laboratory measured analyses produced by inductively coupled plasma mass spectrometry (ICP-MS) and inductively coupled plasma optical emission spectroscopy (ICP-OES). The coal-related geochemical data are derived primarily from the Cretaceous Blackhawk Formation and Ferron Sandstone of Utah, and the Mesaverde Group of Colorado. Additional non-coal resources assessed include oil shale-bearing strata of the Eocene upper Green River Formation (Utah and Colorado), phosphate-rich limestone of the Permian Park City Formation (Utah) and produced water from oil and gas-bearing strata of the Eocene Green River and Wasatch Formations (Uinta Basin) and the Pennsylvanian Paradox Formation (Paradox Basin) (Table 1). The CORE-CM assessment included a wide range of lithologies present in the coal, oil shale, and phosphate geologic resource systems whether or not the specific lithology has current economic value. Geochemical analyses of produced water from oil and gas wells focused on current and emerging hydrocarbon targets in the central Uinta Basin and northern Paradox Basin. A total of 13,092 geochemical analyses from these geologic systems is provided in the included geodatabase. A series of coal quality data (e.g., composition and maceral analyses) is also included in the database and was digitized from archived coal samples from the Utah Geological Survey (Appendix A).

Colorado, Utah↗
USGS2000

Regional evaluation of evapotranspiration in the Everglades

Nine sites in the Florida Everglades were selected and instrumented for collection of data necessary for evapotranspiration-determination using the Bowen-ratio energy-budget method. The sites were selected to represent the sawgrass or cattail marshes, wet prairie, and open-water areas that constitute most of the natural Everglades system. At each site, measurements necessary for evapotranspiration (ET) calculation and modeling were automatically made and stored on-site at 15- or 30-minute intervals. Data collected included air temperature and humidity at two heights, wind speed and direction, incoming solar radiation, net solar radiation, water level and temperature, soil moisture content, soil temperature, soil heat flux, and rainfall. Data summarized in this report were collected from January 1996 through December 1997, and the development of site-specific and regional models of ET for this period is described. Latent heat flux is the energy flux density equivalent of the ET rate. Modified Priestley-Taylor models of latent heat flux as a function of selected independent variables were developed at each site. These models were used to fill in periods of missing latent heat flux measurement, and to develop regional models of the entire Everglades region. The regional models may be used to estimate ET in wet prairie, sawgrass or cattail marsh, and open-water portions of the natural Everglades system. The models are not applicable to forested areas or to the brackish areas adjacent to Florida Bay. Two types of regional models were developed. One type of model uses measurements of available energy at a site, together with incoming solar energy and water depth, to estimate hourly ET. This available-energy model requires site data for net radiation, water heat storage, and soil heat flux, as well as data for incoming solar radiation and water depth. The other type of model requires only incoming solar energy, air temperature, and water depth data to provide estimates of hourly ET. The second model thus uses data that are more readily available than the data required for the available-energy model. Computed ET mean annual totals for all nine sites for the 1996-97 period ranged from 42.4 inches per year at a site where the water level is below land surface for several months each year to 57.4 inches per year at an open-water site with no emergent vegetation. Although the density of photosynthetically-active plant leaves has been shown to relate directly to ET in some studies, it does not appear to relate directly to ET in the Everglades, based on comparison of annual ET data with leaf-area index, defined as the Normalized Difference Vegetation Index (NDVI), data from satellite imagery. NDVI and ET appear to be inversely related in the Everglades. The greatest ET rates occurred at open-water sites where the NDVI data indicated the lowest leaf-area index. Among the remaining vegetated sites, there is no clear relation between ET and NDVI, though the highest ET rate corresponded to the lowest NDVI and one of the lowest ET rates corresponded to the highest NDVI value. The variation in ET follows a seasonal pattern, with lowest monthly ET totals occurring in December through February, and highest ET occurring in May through August. The greatest range in monthly ET among all nine sites for the 2-year period occurred at site 3: from 1.81 inches in December 1997 to 6.84 inches in July 1996. A study to compare the Bowen-ratio/energy balance method of ET measurement with the eddy-correlation method was done at one site from June 22, 1998, through September 28, 1998. This comparison indicated that both methods gave comparable values of the Bowen ratio, but there was a considerable difference in available energy measured by the two methods. The mean of all 30-minute measured turbulent heat fluxes from the eddy-correlation apparatus for June 22 through September 29, 1998, was 137.4 watts per square meter, and the mean of the corresponding measured energy was 163.6 watts per square meter, or about 20 percent greater. The disagreement in mean energy fluxes measured by the two methods is problematical and is not fully understood. Although the difference seems to be related to friction velocity, and is practically non-existent at values of friction velocity greater than 0.3 meter per second, the "correctness" of either method cannot be determined with the data available.

Florida↗