Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Special Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46Linked to original sources
USGS2019

Water-level data for the Albuquerque Basin and adjacent areas, central New Mexico, period of record through September 30, 2018

The Albuquerque Basin, located in central New Mexico, is about 100 miles long and 25–40 miles wide. The basin is hydrologically defined as the extent of consolidated and unconsolidated deposits of Tertiary and Quaternary age that encompasses the structural Rio Grande Rift between San Acacia to the south and Cochiti Lake to the north. A 20-percent population increase in the basin from 1990 to 2000 and a 22-percent population increase from 2000 to 2010 resulted in an increased demand for water in areas within the basin. Drinking-water supplies throughout the basin were obtained solely from groundwater resources until December 2008, when the Albuquerque Bernalillo County Water Utility Authority (ABCWUA) began treatment and distribution of surface water from the Rio Grande through the San Juan-Chama Drinking Water Project. An initial network of wells was established by the U.S. Geological Survey (USGS) in cooperation with the City of Albuquerque from April 1982 through September 1983 to monitor changes in groundwater levels throughout the Albuquerque Basin. In 1983, this network consisted of 6 wells with analog-to-digital recorders and 27 wells where water levels were measured monthly. As of 2018, the network consisted of 120 wells and piezometers. (A piezometer is a specialized well open to a specific depth in the aquifer, often of small diameter and nested with other piezometers open to different depths.) The USGS, in cooperation with the ABCWUA, the New Mexico Office of the State Engineer, and Bernalillo County, measures water levels from the 120 wells and piezometers in the network; this report, prepared in cooperation with the ABCWUA, presents water-level data collected by USGS personnel at those 120 sites through water year 2018 (October 1, 2017, through September 30, 2018). Water levels that were collected from wells in previous water years were published in previous USGS reports.

New Mexico↗
USGS2020

Water-level data for the Albuquerque Basin and adjacent areas, central New Mexico, period of record through September 30, 2019

The Albuquerque Basin, located in central New Mexico, is about 100 miles long and 25–40 miles wide. The basin is hydrologically defined as the extent of consolidated and unconsolidated deposits of Tertiary and Quaternary age that encompasses the structural Rio Grande Rift between San Acacia to the south and Cochiti Lake to the north. A 20-percent population increase in the basin from 1990 to 2000 and a 22-percent population increase from 2000 to 2010 resulted in an increased demand for water in areas within the basin. Drinking-water supplies throughout the basin were obtained solely from groundwater resources until December 2008, when the Albuquerque Bernalillo County Water Utility Authority (ABCWUA) began treatment and distribution of surface water from the Rio Grande through the San Juan-Chama Drinking Water Project. An initial network of wells was established by the U.S. Geological Survey (USGS) in cooperation with the City of Albuquerque from April 1982 through September 1983 to monitor changes in groundwater levels throughout the Albuquerque Basin. In 1983, this network consisted of 6 wells with analog-to-digital recorders and 27 wells where water levels were measured monthly. As of 2019, the network consisted of 120 wells and piezometers. (A piezometer is a specialized well open to a specific depth in the aquifer, often of small diameter and nested with other piezometers screened at different depths.) The USGS, in cooperation with the ABCWUA, the New Mexico Office of the State Engineer, and Bernalillo County, measures water levels from the 120 wells and piezometers in the network; this report, prepared in cooperation with the ABCWUA, presents water-level data collected by USGS personnel at those 120 sites through water year 2019 (October 1, 2018, through September 30, 2019). Water levels that were collected from those discontinued wells in previous water years were published in previous USGS reports.

New Mexico↗
USGS1979

Key to the common marine molluscs of Texas

A dichotomous key is developed which provides the investigator a means for identifying the common marine molluscs on the Texas coast. The key is written as to allow the user to stop or begin at any desired taxonomic level (class, order, superfamily, family, genus, species) depending on prior knowledge or specific need (Table 1). Because of the special importance of bivalves to many studies, species-specific information is provided pertaining to feeding type, relation to substrate, and distribution (Table 2). An illustrated glossary is also provided.

Texas↗
USGS1967

Geohydrologic reconnaissance of the Soquel-Aptos area, Santa Cruz County, California

This report summarizes existing knowledge on the geohydrology of the Soquel-Aptos area, near, and including the eastern part, of Santa Cruz, California, and outlines work necessary for making a complete appraisal of the water resources of the area. The area is underlain mostly by marine and continental sedimentary deposits of Tertiary and Quaternary age. A small section in the northeastern part of the area on the eastern side of the San Andreas fault is underlain by sedimentary and metamorphic rocks of Cretaceous or older age. Quartz diorite, probably of Cretaceous age, underlies a considerable part of the area, but crops out only in small exposures along canyon bottom south of the Zayante fault. The Soquel-Aptos area consists of two main structural blocks?one, downthrown on the northeast side of the Zayante fault; the other, upthrown on the southwest side of the fault. The main water-bearing formations in the southwestern structural block are the Santa Margarita and Purisima Formations. The Purisima, the most widespread of these units in this area, contains water under water-table and artesian conditions and furnishes water to most wells. The water-bearing character of the rocks in the northern structural block is unknown. Presently available geohydrologic data are too limited for detailed evaluation of the ground-water potential in the Soquel-Aptos area. Work needed for a detailed evaluation includes: (1) Geophysical exploration and test drilling at selected locations, (2) pumping tests of selected existing wells and possibly of specially drilled test wells, (3) study and reconnaissance measurements of spring and streamflow, (4) chemical analysis of water samples from selected wells, and (5) establishment of a program for monitoring water quality and water levels in key wells.

California↗
USGS1981

Procedures for the use of aircraft in wildlife biotelemetry studies

This is a report on the state of the art methodology and on questions that arise while one is preparing to use aircraft in a biotelemetry study. In general the first step in preparing to mount an antenna on an aircraft is to consult with a certified aircraft mechanic. Aircraft certification is discussed to provide background information concerning the role of the Federal Aviation Administration (FAA) in regulating the use of biotelemetry antennas on aircraft. However, approval of any specific design of antenna mount rests with local FAA authority. Airplane and helicopter antenna attachments are described. Performance of the receiving antenna system is discussed with emphasis on how variables as aircraft type and antenna configuration may influence reception. The side-looking vs. front-looking antenna configuration and the VHF vs. HF frequency band are generally recommended for most aerial tracking studies. Characteristics of receivers, transmitters, and antennas that might influence tracking are discussed. Specific topics such as calibration of receivers and transmitter quality control are considered. Suggestions in preparing for and conducting tracking flights that will improve overall efficiency and safety are presented. Search techniques, including procedures for conducting large and specific area surveys as well as methods to improve and evaluate search efficiency, are discussed. A concluding section considers special topics such as low-level operations and the use of helicopters. Diagrams of antenna mounts, equipment check-off lists, and antenna test procedures are included as appendices.

Resource Publication↗
USGS2005

The fishes of Wilson's Creek National Battlefield, Missouri, 2003

An inventory of fishes of Wilson's Creek National Battlefield was conducted at eight sites on three streams, two springs, a pond, and within a cave. Fish were sampled using conventional electrofishing equipment during July 2003. Approximately 325 fish were collected and identified from five of the eight sampling sites. A total of 30 species of fish was collected from the eight sampling sites. The number of species collected at the sampling sites ranged from 0 to 23. Many of the 'most commonly' collected fish species are typical of Ozark streams. A preliminary expected species list incorrectly listed 12 species because of incorrect species range or habitat requirements. A thirteenth species (the Ozark cavefish, Amblyopsis rosae) is listed as 'unexpected.' However, this designation is uncertain because Ozark cavefish have been reported from several caves and springs in Greene County. Upon revising the list of expected species, the inventory yielded 30 of the 53 species (57 percent). Ten of the 30 fish species collected in this inventory previously had not been collected at Wilson's Creek National Battlefield. However, eight species collected in one or more of the two previous inventories were not collected in this effort. It is unknown if any change in environmental conditions has occurred that is responsible for the absence of these species. Although none of the species collected in this study are federally-listed threatened or endangered species, five species collected at Wilson's Creek National Battlefield may be of special interest to National Park Service managers and others because they are endemic to the Ozark Plateaus. The duskystripe shiner (Luxilus pilsbryi), Ozark bass (Ambloplites constellatus), Ozark chub (Erimystax harryi), and stippled darter (Etheostoma punctulatum) are common and found throughout much of the Ozark Plateaus. However, the Ozark sculpin (Cottus hypselurus) has a more limited range and more specific habitat requirements.

Scientific Investigations Report↗
USGS2022

Reference genome of the California glossy snake, Arizona elegans occidentalis: A declining California Species of Special Concern

The glossy snake ( Arizona elegans ) is a polytypic species broadly distributed across southwestern North America. The species occupies habitats ranging from California’s coastal chaparral to the shortgrass prairies of Texas and southeastern Nebraska, to the extensive arid scrublands of central México. Three subspecies are currently recognized in California, one of which is afforded state-level protection based on the extensive loss and modification of its preferred alluvial coastal scrub and inland desert habitat. We report the first genome assembly of A. elegans occidentalis as part of the California Conservation Genomics Project (CCGP). Consistent with the reference genome strategy of the CCGP, we used Pacific Biosciences HiFi long reads and Hi-C chromatin-proximity sequencing technologies to produce a de novo assembled genome. The assembly comprises a total of 140 scaffolds spanning 1,842,602,218 base pairs, has a contig NG50 of 61 Mb, a scaffold NG50 of 136 Mb, and a BUSCO complete score of 95.9%, and is one of the most complete snake genome assemblies. The A. e. occidentalis genome will be a key tool for understanding the genomic diversity and the basis of adaptations within this species and close relatives within the hyperdiverse snake family Colubridae.

California↗
USGS2007

Pattern and potential causes of White-faced Ibis, Plegadis chihi, establishment in the northern prairie and parkland region of North America

The Northern Prairie and Parkland Waterbird Conservation Plan calls for renewed attention to determining the current status of waterbird populations, their distributions, and conservation needs. It highlights the need for baseline information on the White-faced Ibis (Plegadis chihi). In response, we examined the historical and current distribution of the ibis in North Dakota and summarized first sightings and nest records for the provinces and other states composing the northern prairie and parkland region. The establishment of breeding colonies of White-faced Ibis here may be due to climate and precipitation patterns, invasion and spread of Narrowleaf Cattail (Typha angustifolia), changes in agricultural practices, habitat loss and range expansion in the southern and western portions of the species' range, and increases in ibis populations in the Intermountain West. We placed special emphasis on North Dakota, a state for which there is scant published information concerning the current status of this species. In recent decades, the ibis has become a regular breeding-season resident in North Dakota and in other areas of the northern prairie and parkland region. From 1882 to 2002, there were 145 reports of one or more White-faced Ibis in North Dakota, including 93 reports during the breeding season (15 May to 31 August), 49 during the non-breeding season (1 September to 14 May), and three for which the season of occurrence was not reported. Prior to the 1960s, there were only three records of the species in North Dakota. Observations of White-faced Ibises in North Dakota increased dramatically between the 1960s and the early 21st century, and the species has been observed nearly annually since 1971. The first White-faced Ibis nesting activity in the state was recorded in 1978, and to date, there have been 21 known records of nesting activity in the state. The species nested in large (>300 ha) semipermanent or permanent wetlands within mixed-species colonies ranging in areal extent from small (0.1 ha) to fairly large (27 ha), and colonies were located in patches of emergent vegetation dominated by cattails (Typha) and bulrushes (Scirpus). We classify the White-faced Ibis as a fairly common migrant and a locally uncommon breeder east of the Missouri River and a casual migrant west of the Missouri River.

Canadian Field-Naturalist↗
USGS2008

EAARL coastal topography - Northern Gulf of Mexico

These remotely sensed, geographically referenced elevation measurements of Lidar-derived coastal topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. One objective of this research is to create techniques to survey areas for the purposes of geomorphic change studies following major storm events. The USGS Coastal and Marine Geology Program's National Assessment of Coastal Change Hazards project is a multi-year undertaking to identify and quantify the vulnerability of U.S. shorelines to coastal change hazards such as effects of severe storms, sea-level rise, and shoreline erosion and retreat. Airborne Lidar surveys conducted during periods of calm weather are compared to surveys collected following extreme storms in order to quantify the resulting coastal change. Other applications of high-resolution topography include habitat mapping, ecological monitoring, volumetric change detection, and event assessment. The purpose of this project is to provide highly detailed and accurate datasets of the northern Gulf of Mexico coastal areas, acquired on September 19, 2004, immediately following Hurricane Ivan. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Airborne Advanced Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532 nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking RGB (red-green-blue) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers and an integrated miniature digital inertial measurement unit which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system on September 19, 2004. The survey resulted in the acquisition of 3.2 gigabytes of data. The data were processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of 'last return' elevations.

Alabama, Florida, Mississippi↗
USGS2008

EAARL coastal topography — Fire Island National Seashore 2007

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) and bare earth (BE) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of Fire Island National Seashore in New York, acquired on April 29-30 and May 15-16, 2007. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL) was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

New York↗
USGS2008

EAARL coastal topography — Sandy Hook 2007

These remotely sensed, geographically referenced elevation measurements of Lidar-derived topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of Gateway National Recreation Area's Sandy Hook Unit in New Jersey, acquired on May 16, 2007. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL) was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

New York↗
USGS2008

EAARL submerged topography– U.S. Virgin Islands 2003

These remotely sensed, geographically referenced elevation measurements of Lidar-derived submerged topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), South Florida-Caribbean Network, Miami, FL; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate bathymetric datasets of a portion of the U.S. Virgin Islands, acquired on April 21, 23, and 30, May 2, and June 14 and 17, 2003. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

St John Island↗
USGS2009

EAARL Coastal Topography - Northern Gulf of Mexico, 2007: First surface

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) elevation data were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Gulf Coast Network, Lafayette, LA; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. The project provides highly detailed and accurate datasets of select barrier islands and peninsular regions of Louisiana, Mississippi, Alabama, and Florida, acquired June 27-30, 2007. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Alabama, Mississippi↗
USGS2009

EAARL coastal topography — Northern Gulf of Mexico, 2007: Bare earth

These remotely sensed, geographically referenced elevation measurements of Lidar -derived bare earth ( BE ) topography were produced as a collaborative effort between the U.S. Geological Survey ( USGS ), Florida Integrated Science Center ( FISC ), St. Petersburg, FL ; the National Park Service ( NPS ), Gulf Coast Network, Lafayette, LA ; and the National Aeronautics and Space Administration ( NASA ), Wallops Flight Facility, VA . The purpose of this project is to provide highly detailed and accurate datasets of select barrier islands and peninsular regions of Louisiana, Mississippi, Alabama, and Florida, acquired on June 27-30, 2007. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar ( EAARL ), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar , a down-looking red-green-blue ( RGB ) digital camera, a high-resolution multi-spectral color infrared ( CIR ) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system and the resulting data were then processed using the Airborne Lidar Processing System ( ALPS ), a custom-built processing system developed in a NASA - USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

northern Gulf of Mexico↗
USGS1973

High survival and homing rate of hand-reared wild-strain mallards

In the summer of 1970, 648 (329 males and 319 females) hand-reared wild-strain mallards ( Anas platyrhynchos ) were banded and released at the Arrowwood National Wildlife Refuge, Edmunds, North Dakota. The females were also marked with numbered nasal saddles. Liberation was by the gentle release method, and no special effort was made to isolate or condition the ducklings prior to release. Ducklings were placed in an enclosed pond area at 25 to 45 days of age. Altogether, 627 (97 percent) ducklings reached flight age and dispersed gradually into the wild. All had left the release area by 25 November. First-year band recovery reports indicated that 68 (11 percent) of the birds were shot in 15 states. Their migration pattern was similar to that for immature wild mallards banded in North Dakota in 1970. Eighty-nine (33 percent) of a possible 270 marked females returned to Arrowwood Refuge during 1971. When consideration is given to assumed normal natural mortality and crippling loss, an estimated minimum of 43 percent of the surviving females returned to the release area. Returning birds not observed would raise this figure even higher. This potential homing rate is considerably higher than rates reported for other studies using various strains of mallards. Numerous observations of nests and broods indicated that breeding behavior and nesting success were similar to those of wild mallards in the area. The success of this release is attributed to the inherent capability of hand-reared, wild-strain mallards to revert to their wild behavior, and to the high survival to flight age and first fall migration afforded by the gentle release in a sanctuary area. Indications are that releases of this type under the described conditions can be used to increase the breeding population of mallards in a local area.

North Dakota↗
USGS1973

Field reconnaissance of the effects of the earthquake of April 13, 1973, near Laguna de Arenal, Costa Rica

At about 3:34 a.m. on April 13, 1973, a moderate-sized, but widely-felt, earthquake caused extensive damage with loss of 23 lives in a rural area of about 150 km 2 centered just south of Laguna de Arenal in northwestern Costa Rica (fig. 1). This report summarizes the results of the writer's reconnaissance investigation of the area that was affected by the earthquake of April 13, 1973. A 4-day field study of the meizoseismal area was carried out during the period from April 28 through May 1 under the auspices of the U.S. Geological Survey. The primary objective of this study was to evaluate geologic factors that contributed to the damage and loss of life. The earthquake was also of special interest because of the possibility that it was accompanied by surface faulting comparable to that which occurred at Managua, Nicaragua, during the disastrous earthquake of December 23, 1972 (Brown, Ward, and Plafker, 1973). Such earthquake-related surface faulting can provide scientifically valuable information on active tectonic processes at shallow depths within the Middle America arc. Also, identification of active faults in this area is of considerable practical importance because of the planned construction of a major hydroelectrical facility within the meizoseismal area by the Instituto Costarricense de Electricidad (I.C.E.). The project would involve creation of a storage reservoir within the Laguna de Arenal basin and part of the Río Arenal valley with a 75 m-high earthfill dam across Río Arenal at a point about 10 km east of the outlet of Laguna de Arenal.

Laguna De Arenal↗
USGS2016

External influences on ecological theory: Report on organized oral Session 80 at the 100th Anniversary Meeting of the Ecological Society of America

The 100‐year history of the Ecological Society of America spans most of the major advances in the field of ecology, from the “niche” of Grinnell and others, to Lotka and Volterra's models of predation and competition based on the logistic growth equation, to the concept of competitive exclusion developed from experimental ecology, to genetics and evolutionary ecology and all the ramifications and specializations of these topics over the rest of the 20th and into the 21st century. The objective of this session, sponsored by the Historical Records Committee of the ESA, was to explore how ecological concepts have been shaped and changed by influences that are external to the scientific method, such as funding priorities, ideology, politics, personalities, and differences between the ecosystems where influential ecologists developed their ideas. Among the many memorable quotations of the philosopher/poet George Santayana (1863–1952) is the often quoted and misquoted observation, “Those who cannot remember the past are condemned to repeat it.”

Bulletin of the Ecological Society of America↗
USGS2018

Supporting natural resource management—The role of economics at the Department of the Interior—A workshop report

The first U.S. Department of the Interior Economics Workshop was held April 5–7, 2017 in Washington, D.C., to identify, highlight, and better understand needs and opportunities for economic analysis to support the Department of the Interior’s mission. The Economics Workshop, jointly convened by the Department of the Interior Office of Policy Analysis and the U.S. Geological Survey Science and Decisions Center, provided an opportunity for Department of the Interior’s economists to share expertise and experiences and to build collaboration and communication channels across the Department of the Interior. Natural and cultural resource managers face complex questions and often have to balance competing stakeholder interests. Per the mission statement, the Department of the Interior “protects and manages the Nation’s natural resources and cultural heritage; provides scientific and other information about those resources; and honors its trust responsibilities or special commitments to American Indians, Alaska Natives, and affiliated island communities.” Economic analysis is relevant to issues integral to nearly all the land and water management decisions made by the Department of the Interior. More than 80 Department of the Interior economists gathered at the Economics Workshop to share their work, discuss common challenges, and identify approaches to advance the use and contribution of economics at the Department of the Interior.

Open-File Report↗