Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Ground Water”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39Linked to original sources
USGS2014

Long-term trends of ground-water levels in the United States

Ground-water levels at the end of 1954 were at or near record-low stages throughout most of the southern two-thirds of the United States. These low stages, like those of the early 1930's, have led to frequent expression of the opinion that the water table throughout the country is continuously falling and that we are gradually exhausting our ground-water supplies. A good record of changes in ground-water levels is being obtained by the United States Geological Survey and cooperating State agencies from periodical measurements of water levels in nearly 20,000 observation wells. The records of some of these wells extend back 50 years. Many records are available for the period beginning in 1934. These long-term records indicate that in some areas the ground-water supply is overdeveloped. In the great majority of areas, however, the stage of the water levels correlates with the precipitation. Much of the country has been in drought and the water levels are at a low stage. As the precipitation increases, as it is bound to do later, the water levels will return to higher stages.

Eos, Transactions, American Geophysical Union↗
USGS1995

Ground-water recharge in Escambia and Santa Rosa Counties, Florida

Ground water is a major component of Florida's water resources, accounting for 90 percent of all public-supply and self-supplied domestic water withdrawals, and 58 percent of self-supplied commercial-industrial and agricultural withdrawals of freshwater (Marella, 1992). Ground-water is also an important source of water for streams, lakes, and wetlands in Florida. Because of their importance, a good understanding of these resources is essential for their sound development, use, and protection. One area in which our understanding is lacking is in characterizing the rate at which ground water in aquifers is recharged, and how recharge rates vary geographically. Ground-water recharge (recharge) is the replenishment of ground water by downward infiltration of water from rainfall, streams, and other sources (American Society of Civil Engineers, 1987, p. 222). The recharge rates in many areas of Florida are unknown, of insufficient accuracy, or mapped at scales that are too coarse to be useful. Improved maps of recharge rates will result in improved capabilities for managing Florida's ground-water resources. In 1989, the U.S. Geological Survey, in cooperation with the Florida Department of Environmental Regulation, began a study to delineate high-rate recharge areas in several regions of Florida (Vecchioli and others, 1990). This study resulted in recharge maps that delineated areas of high (greater than 10 inches per year) and low (0 to 10 inches per year) recharge in three counties--Okaloosa, Pasco, and Volusia Counties--at a scale of 1:100,000. This report describes the results of a similar recharge mapping study for Escambia and Santa Rosa Counties (fig. 1), in which areas of high- and low-rates of recharge to the sand-and-gravel aquifer and Upper Floridan aquifer are delineated. The study was conducted in 1992 and 1993 by the U.S. Geological Survey in cooperation with the Florida Department of Environmental Protection.

Florida↗
USGS2006

Physical and hydrochemical evidence of lake leakage near Jim Woodruff Lock and Dam and of ground-water inflow to Lake Seminole, and an assessment of karst features in and near the lake, southwestern Georgia and northwestern Florida

Hydrogeologic data and water-chemistry analyses indicate that Lake Seminole leaks into the Upper Floridan aquifer near Jim Woodruff Lock and Dam, southwestern Georgia and northwestern Florida, and that ground water enters Lake Seminole along upstream reaches of the lake’s four impoundment arms (Chattahoochee and Flint Rivers, Spring Creek, and Fishpond Drain). Written accounts by U.S. Army Corps of Engineers geologists during dam construction in the late 1940s and early 1950s, and construction-era photographs, document karst-solution features in the limestone that comprise the lake bottom and foundation rock to the dam, and confirm the hydraulic connection of the lake and aquifer. More than 250 karst features having the potential to connect the lake and aquifer were identified from preimpoundment aerial photographs taken during construction. An interactive map containing a photomosaic of 53 photographic negatives was orthorectfied to digital images of 1:24,000-scale topographic maps to aid in identifying karst features that function or have the potential to function as locations of water exchange between Lake Seminole and the Upper Floridan aquifer. Some identified karst features coincide with locations of mapped springs, spring runs, and depressions that are consistent with sinkholes and sinkhole ponds. Hydrographic surveys using a multibeam echosounder (sonar) with sidescan sonar identified sinkholes in the lake bottom along the western lakeshore and in front of the dam. Dye-tracing experiments indicate that lake water enters these sinkholes and is transported through the Upper Floridan aquifer around the west side of the dam at velocities of about 500 feet per hour to locations where water "boils up" on land (at Polk Lake Spring) and in the channel bottom of the Apalachicola River (at the "River Boil"). Water discharging from Polk Lake Spring joins flow from a spring-fed ground-water discharge zone located downstream of the dam; the combined flow disappears into a sinkhole located on the western floodplain of the river and is transmitted through the Upper Floridan aquifer, eventually discharging to the Apalachicola River at the River Boil. Acoustic Doppler current profiling yielded flow estimates from the River Boil in the range from about 140 to 220 cubic feet per second, which represents from about 1 to 3 percent of the average daily flow in the river. Binary mixing-model analysis using naturally occurring isotopes of oxygen and hydrogen (oxygen-18 and deuterium) indicates that discharge from the River Boil consists of a 13-to-1 ratio of lake water to ground water and that other sources of lake leakage and discharge to the boil probably exist. Analyses of major ions, nutrients, radon-222, and stable isotopes of hydrogen and oxygen contained in water samples collected from 29 wells, 7 lake locations, and 5 springs in the Lake Seminole area during 2000 indicate distinct chemical signatures for ground water and surface water. Ground-water samples contained higher concentrations of calcium and magnesium, and higher alkalinity and specific conductance than surface-water samples, which contained relatively high concentrations of total organic carbon and sulfate. Solute and isotopic tracers indicate that, from May to October 2000, springflow exhibited more ground-water qualities (high specific conductance, low dissolved oxygen, and low temperature) than surface water; however, the ratio of ground water to surface water of the springs was difficult to quantify from November to April because of reduced springflow and rapid mixing of springflow and lake water during sampling. The saturation index of calcite in surface-water samples indicates that while surface water is predominately undersaturated with regard to calcite year-round, a higher potential for dissolution of the limestone matrix exists from late fall through early spring than during summer. The relatively short residence time (5–7 hours) and rapid flow velocity (nearly 500 feet per hour) of lake water leaking into the Upper Floridan aquifer and exiting at the River Boil in the Apalachicola River implies that calcite-undersaturated water is in constant contact with the limestone, increasing the potential for limestone dissolution and enlargement of flow pathways by erosion. A relatively low potential exists, however, for limestone dissolution to cause sudden sinkhole collapse followed by catastrophic lake drainage because ground-water levels close to the lake, except near the dam, are nearly the same as lake stage, resulting in low vertical and lateral hydraulic gradients and low flow between the lake and aquifer. An increased potential for lake leakage and sinkhole formation and collapse exists near some in-lake springs during colder months of the year, as density differences and the hydraulic potential between lake water and ground water establish the conditions for calcite-undersaturated lake water to enter nonflowing springs and contact limestone.

Florida, Georgia↗
USGS1998

Application of nonlinear-regression methods to a ground-water flow model of the Albuquerque Basin, New Mexico

This report documents the application of nonlinear-regression methods to a numerical model of ground-water flow in the Albuquerque Basin, New Mexico. In the Albuquerque Basin, ground water is the primary source for most water uses. Ground-water withdrawal has steadily increased since the 1940's, resulting in large declines in water levels in the Albuquerque area. A ground-water flow model was developed in 1994 and revised and updated in 1995 for the purpose of managing basin ground- water resources. In the work presented here, nonlinear-regression methods were applied to a modified version of the previous flow model. Goals of this work were to use regression methods to calibrate the model with each of six different configurations of the basin subsurface and to assess and compare optimal parameter estimates, model fit, and model error among the resulting calibrations. The Albuquerque Basin is one in a series of north trending structural basins within the Rio Grande Rift, a region of Cenozoic crustal extension. Mountains, uplifts, and fault zones bound the basin, and rock units within the basin include pre-Santa Fe Group deposits, Tertiary Santa Fe Group basin fill, and post-Santa Fe Group volcanics and sediments. The Santa Fe Group is greater than 14,000 feet (ft) thick in the central part of the basin. During deposition of the Santa Fe Group, crustal extension resulted in development of north trending normal faults with vertical displacements of as much as 30,000 ft. Ground-water flow in the Albuquerque Basin occurs primarily in the Santa Fe Group and post-Santa Fe Group deposits. Water flows between the ground-water system and surface-water bodies in the inner valley of the basin, where the Rio Grande, a network of interconnected canals and drains, and Cochiti Reservoir are located. Recharge to the ground-water flow system occurs as infiltration of precipitation along mountain fronts and infiltration of stream water along tributaries to the Rio Grande; subsurface flow from adjacent regions; irrigation and septic field seepage; and leakage through the Rio Grande, canal, and Cochiti Reservoir beds. Ground water is discharged from the basin by withdrawal; evapotranspiration; subsurface flow; and flow to the Rio Grande, canals, and drains. The transient, three-dimensional numerical model of ground-water flow to which nonlinear-regression methods were applied simulates flow in the Albuquerque Basin from 1900 to March 1995. Six different basin subsurface configurations are considered in the model. These configurations are designed to test the effects of (1) varying the simulated basin thickness, (2) including a hypothesized hydrogeologic unit with large hydraulic conductivity in the western part of the basin (the west basin high-K zone), and (3) substantially lowering the simulated hydraulic conductivity of a fault in the western part of the basin (the low-K fault zone). The model with each of the subsurface configurations was calibrated using a nonlinear least- squares regression technique. The calibration data set includes 802 hydraulic-head measurements that provide broad spatial and temporal coverage of basin conditions, and one measurement of net flow from the Rio Grande and drains to the ground-water system in the Albuquerque area. Data are weighted on the basis of estimates of the standard deviations of measurement errors. The 10 to 12 parameters to which the calibration data as a whole are generally most sensitive were estimated by nonlinear regression, whereas the remaining model parameter values were specified. Results of model calibration indicate that the optimal parameter estimates as a whole are most reasonable in calibrations of the model with with configurations 3 (which contains 1,600-ft-thick basin deposits and the west basin high-K zone), 4 (which contains 5,000-ft-thick basin de

New Mexico↗
USGS2005

Age and quality of ground water and sources of nitrogen in the surficial aquifers in Pumpkin Creek Valley, western Nebraska, 2000

Ground water is the source of drinking water for the residents of Pumpkin Creek Valley, western Nebraska. In this largely agricultural area, shallow aquifers potentially are susceptible to nitrate contamination. During the last 10 years, ground-water levels in the North Platte Natural Resources District have declined and contamination has become a major problem for the district. In 2000, the U.S. Geological Survey and the North Platte Natural Resources District began a cooperative study to determine the age and quality of the ground water and the sources of nitrogen in the aquifers in Pumpkin Creek Valley. Water samples were collected from 8 surface-water sites, 2 springs, and 88 ground-water sites during May, July, and August 2000. These samples were analyzed for physical properties, nutrients or nitrate, and hydrogen and oxygen isotopes. In addition, a subset of samples was analyzed for any combination of chlorofluorocarbons, tritium, tritium/helium, sulfur-hexafluoride, carbon-14, and nitrogen-15. The apparent age of ground water in the alluvial aquifer typically varied from about 1980 to modern, whereas ground water in the fractured Brule Formation had a median value in the 1970s. The Brule Formation typically contained ground water that ranged from the 1940s to the 1990s, but low-yield wells had apparent ages of 5,000 to 10,000 years before present. Data for oxygen-18 and deuterium indicated that lake-water samples showed the greatest effects from evaporation. Ground-water data showed no substantial evaporative effects and some ground water became isotopically heavier as the water moved downgradient. In addition, the physical and chemical ground-water data indicate that Pumpkin Creek is a gaining stream because little, if any, of its water is lost to the ground-water system. The water-quality type changed from a sodium calcium bicarbonate type near Pumpkin Creek's headwaters to a calcium sodium bicarbonate type near its mouth. Nitrate concentrations were largest in the alluvial system (median = 5 mg/L) and smallest in the surface-water system (median = 1 mg/L). Most nitrate concentrations exceeding the U.S. Environmental Protection Agency maximum contaminant level for drinking water of 10 mg/L as nitrogen were adjacent to irrigated fields and in areas where alluvial sediments are less than 50 ft thick. Sources of nitrogen in the ground water of the study area included naturally occurring nitrogen, commercial fertilizer, and animal waste. Based on nitrate concentration and delta nitrogen-15, the nitrogen in 65 percent of the water samples appears to have originated from a mixture of commercial fertilizers and animal waste. Some of the smallest nitrate concentrations in the ground-water samples contained some of the largest delta nitrogen-15 values (greater than 10 per mil), which suggests animal waste as the likely source. Commercial fertilizers were the likely source of most of the nitrogen in water samples with nitrate concentrations that exceeded 10 mg/L. The source of the nitrogen in water samples with nitrate concentrations exceeding 10 mg/L, but with delta nitrogen-15 values close to 10 per mil, could not be determined.

Nebraska↗
USGS2007

Comparison of local- to regional-scale estimates of ground-water recharge in Minnesota, USA

Regional ground-water recharge estimates for Minnesota were compared to estimates made on the basis of four local- and basin-scale methods. Three local-scale methods (unsaturated-zone water balance, water-table fluctuations (WTF) using three approaches, and age dating of ground water) yielded point estimates of recharge that represent spatial scales from about 1 to about 1000 m 2 . A fourth method (RORA, a basin-scale analysis of streamflow records using a recession-curve-displacement technique) yielded recharge estimates at a scale of 10–1000s of km 2 . The RORA basin-scale recharge estimates were regionalized to estimate recharge for the entire State of Minnesota on the basis of a regional regression recharge (RRR) model that also incorporated soil and climate data. Recharge rates estimated by the RRR model compared favorably to the local and basin-scale recharge estimates. RRR estimates at study locations were about 41% less on average than the unsaturated-zone water-balance estimates, ranged from 44% greater to 12% less than estimates that were based on the three WTF approaches, were about 4% less than the age dating of ground-water estimates, and were about 5% greater than the RORA estimates. Of the methods used in this study, the WTF method is the simplest and easiest to apply. Recharge estimates made on the basis of the UZWB method were inconsistent with the results from the other methods. Recharge estimates using the RRR model could be a good source of input for regional ground-water flow models; RRR model results currently are being applied for this purpose in USGS studies elsewhere.

Minnesota↗
USGS1998

Nitrate and pesticides in ground water in the eastern San Joaquin Valley, California : Occurrence and trends

The occurrence of nitrate and pesticides in ground water in California's eastern San Joaquin Valley may be greatly influenced by the long history of intensive farming and irrigation and the generally permeable sediments. This study, which is part of the U.S. Geological Survey National Water-Quality Assessment Program, was done to assess the quality of the ground water and to do a preliminary evaluation of the temporal trends in nitrate and pesticides in the alluvial fans of the eastern San Joaquin Valley. Ground-water samples were collected from 30 domestic wells in 1995 (each well was sampled once during 1995). The results of the analyses of these samples were related to various physical and chemical factors in an attempt to understand the processes that control the occurrence and the concentrations of nitrate and pesticides. A preliminary evaluation of the temporal trends in the occurrence and the concentration of nitrate and pesticides was done by comparing the results of the analyses of the 1995 ground-water samples with the results of the analyses of the samples collected in 1986-87 as part of the U.S. Geological Survey Regional Aquifer-System Analysis Program. Nitrate concentrations (dissolved nitrate plus nitrite, as nitrogen) in ground water sampled in 1995 ranged from less than 0.05 to 34 milligrams per liter, with a median concentration of 4.6 milligrams per liter. Nitrate concentrations exceeded the maximum contaminant level of 10 milligrams per liter (as nitrogen) in 5 of the 30 ground-water samples (17 percent), whereas 12 of the 30 samples (40 percent) had nitrate concentrations less than 3.0 milligrams per liter. The high nitrate concentrations were associated with recently recharged, well-oxygenated ground water that has been affected by agriculture (indicated by the positive correlations between nitrate, dissolved-oxygen, tritium, and specific conductance). Twelve pesticides were detected in 21 of the 30 ground-water samples (70 percent) in 1995, although only 5 pesticides were detected in more than 10 percent of the ground-water samples. All 12 pesticides were detected at concentrations below the maximum contaminant levels, except the banned soil fumigants 1,2-dibromo-3-chloropropane (3 detections) and 1,2-dibromoethane (1 detection). Atrazine and desethyl atrazine (a transformation product of atrazine) were the most frequently detected pesticides; they were detected in 11 ground-water samples. The frequent detections of atrazine and desethyl atrazine may be related either to past applications of atrazine or to recent application on rights-of-way. Simazine was detected in 10 ground-water samples and diuron was detected in 4 ground-water samples. The detections of simazine and diuron are generally consistent with their reported applications on the crops near the wells where they were detected. 1,2,3-trichloropropane, a manufacturing by-product of 1,2-dichloropropane and 1,3- dichloropropene formulations, was detected in 4 ground-water samples. The occurrence of 1,2,3-trichloropropane, 1,2-dibromo-3-chloropropane, and 1,2-dibromoethane is probably related to past use. Similar to nitrate concentrations, pesticide occurrence was positively correlated to dissolved-oxygen concentrations, indicating that areas with high dissolved-oxygen concentrations may be vulnerable to contamination by nitrate and pesticides. High dissolved-oxygen concentrations may be associated with water that has been rapidly recharged. A comparison of the concentrations and the occurrence of nitrate and pesticides between 1986-87 and 1995 indicates that nitrate concentrations may pose a greater threat to the quality of the ground-water resource in this region than pesticides, in the context of current drinking-water standards. Nitrate concentrations were significantly higher in the 1995 ground-water samples than in the 1986-87 samples collected from the same wells.

Calfornia↗
USGS1984

An overview of ground-water quality data in Wisconsin

This report contains a summary of ground-water-quality data for Wisconsin and an evaluation of the adequacy of these data for assessing the impact of land disposal of wastes on ground-water quality. Chemical analyses used in data summaries were limited to those stored in the USGS computer system (WATSTORE). Information on documented instances of ground-water contamination and sources of potential contamination from land disposal of wastes was provided by the Wisconsin Department of Natural Resources. Available data provide an overview of ground water quality but may be insufficient for assessment of ground-water contamination from land disposal of wastes. Many sources of potential ground-water contamination (landfills, surface waste-storage impoundments, and buried tanks) are known. Some of these are probably causing local ground-water contamination that is not apparent from available regional data. Information needs for assessment of ground-water contamination from land disposal of wastes include improved understanding of both ground-water hydrology and the chemical behavior of specific contaminants in the environment. (USGS)

Wisconsin↗
USGS2008

Simulations of Ground-Water Flow, Transport, Age, and Particle Tracking near York, Nebraska, for a Study of Transport of Anthropogenic and Natural Contaminants (TANC) to Public-Supply Wells

Contamination of public-supply wells has resulted in public-health threats and negative economic effects for communities that must treat contaminated water or find alternative water supplies. To investigate factors controlling vulnerability of public-supply wells to anthropogenic and natural contaminants using consistent and systematic data collected in a variety of principal aquifer settings in the United States, a study of Transport of Anthropogenic and Natural Contaminants to public-supply wells was begun in 2001 as part of the U.S. Geological Survey National Water-Quality Assessment Program. The area simulated by the ground-water flow model described in this report was selected for a study of processes influencing contaminant distribution and transport along the direction of ground-water flow towards a public-supply well in southeastern York, Nebraska. Ground-water flow is simulated for a 60-year period from September 1, 1944, to August 31, 2004. Steady-state conditions are simulated prior to September 1, 1944, and represent conditions prior to use of ground water for irrigation. Irrigation, municipal, and industrial wells were simulated using the Multi-Node Well package of the modular three-dimensional ground-water flow model code, MODFLOW-2000, which allows simulation of flow and solutes through wells that are simulated in multiple nodes or layers. Ground-water flow, age, and transport of selected tracers were simulated using the Ground-Water Transport process of MODFLOW-2000. Simulated ground-water age was compared to interpreted ground-water age in six monitoring wells in the unconfined aquifer. The tracer chlorofluorocarbon-11 was simulated directly using Ground-Water Transport for comparison with concentrations measured in six monitoring wells and one public supply well screened in the upper confined aquifer. Three alternative model simulations indicate that simulation results are highly sensitive to the distribution of multilayer well bores where leakage can occur and that the calibrated model resulted in smaller differences than the alternative models between simulated and interpreted ages and measured tracer concentrations in most, but not all, wells. Results of the first alternative model indicate that the distribution of young water in the upper confined aquifer is substantially different when well-bore leakage at known abandoned wells and test holes is removed from the model. In the second alternative model, simulated age near the bottom of the unconfined aquifer was younger than interpreted ages and simulated chlorofluorocarbon-11 concentrations in the upper confined aquifer were zero in five out of six wells because the conventional Well Package fails to account for flow between model layers though well bores. The third alternative model produced differences between simulated and interpreted ground-water ages and measured chlorofluorocarbon-11 concentrations that were comparable to the calibrated model. However, simulated hydraulic heads deviated from measured hydraulic heads by a greater amount than for the calibrated model. Even so, because the third alternative model simulates steady-state flow, additional analysis was possible using steady-state particle tracking to assess the contributing recharge area to a public supply well selected for analysis of factors contributing to well vulnerability. Results from particle-tracking software (MODPATH) using the third alternative model indicates that the contributing recharge area of the study public-supply well is a composite of elongated, seemingly isolated areas associated with wells that are screened in multiple aquifers. The simulated age distribution of particles at the study public-supply well indicates that all water younger than 58 years travels through well bores of wells screened in multiple aquifers. The age distribution from the steady-state model using MODPATH estimates the youngest 7 percent of the water to have a flow-weighted mean age

Scientific Investigations Report↗
USGS2006

Ground water recharge and discharge in the central Everglades

Rates of ground water recharge and discharge are not well known in the central Everglades. Here we report estimates of ground water recharge and discharge at 15 sites in the Everglades Nutrient Removal Project and in Water Conservation Area 2A (WCA-2A), along with measurements of hydraulic properties of peat at 11 sites. A simple hydrogeologic simulation was used to assess how specific factors have influenced recharge and discharge. Simulations and measurements agreed that the highest values of recharge and discharge occur within 600 m of levees, the result of ground water flow beneath levees. There was disagreement in the interior wetlands of WCA-2A (located > 1000 m from levees) where measurements of recharge and discharge were substantially higher than simulated fluxes. A five-year time series (1997 to 2002) of measured fluxes indicated that recharge and discharge underwent reversals in direction on weekly, monthly, and annual timescales at interior sites in WCA-2A. Ground water discharge tended to occur during average to moderately dry conditions when local surface water levels were decreasing. Recharge tended to occur during moderately wet periods or during very dry periods just as water levels began to increase following precipitation or in response to a pulse of surface water released from water-control structures by water managers. Discharge also tended to occur at sites in the wetland interior for ∼1 week preceding the arrival of the surface water pulse. We conclude that ground water recharge and discharge vary cyclically in the interior wetlands of the central Everglades, driven by the differential responses of surface water and ground water to annual, seasonal, and weekly trends in precipitation and operation of water-control structures.

Florida↗
USGS2007

A field test of electromigration as a method for remediating sulfate from shallow ground water

Eloctromigraiion offers a potential tool for remediating ground water contaminated with highly soluble components, such as Na + , Cl, NO 3 and SO 4 − . A field experiment was designed to lest the efficacy of electromigration for preconcontrating dissolved SO 4 2 in ground water associated with a fossil-fuel power plant. Two shallow wells, 25 feel apart (one 25 feel deep, the other 47 feet deep), were constructed in the upper portion of an unconfined alluvial aquifer. The wells were constructed with a double-wall design, with an outer casing of 4-inch PVC and an inner lube of 2-inch FVC; both were fully slotted (0.01 inch). Electrodes were constructed by wrapping the inner lulling with a 100-foot length of rare-earth metal oxide/copper wire. An electrical potential of 10.65 volts DC Was applied, and tests were run for periods of 12, 44, and 216 hours. Results showed large changes in the pH from the initial pH of ground water of about 7.5 to values of approximately 2 and 12 at the anode and cathode, respectively. Despite the fact that the test conditions were far from ideal, dissolved SO 4 2- ; was significantly concentrated at the anode. Over a period of approximately nine days, the concentration of SO 4 2- at the anode reached what appeared to he a steady-state value of 2200 mg/L. compared lo the initial value in ground water of approximately 1150 mg/L. The results of this field lest should encourage further investigation of electromigration as a tool in the remediation of contaminated ground water.

Ground Water Monitoring and Remediation↗
USGS1999

The Sparta aquifer in Arkansas' critical ground-water areas: Response of the aquifer to supplying future water needs

The Sparta aquifer is a confined aquifer of great regional importance that comprises a sequence of unconsolidated sand, silt, and clay units extending across much of eastern and southeastern Arkansas and into adjoining States. Water use from the aquifer has doubled since 1975 and continues to increase, and large water-level declines are occurring in many areas of the aquifer. To focus State attention and resources on the growing problem and to provide a mechanism for locally based education and management, the Arkansas Soil and Water Conservation Commission has designated Critical Ground-Water Areas in some counties (see page 6, ?What is a Critical Ground-Water Area??). Ground-water modeling study results show that the aquifer cannot continue to meet growing water-use demands. Dewatering of the primary producing sands is predicted to occur within 10 years in some areas if current trends continue. The predicted dewatering will cause reduced yields and damage the aquifer. Modeling also shows that a concerted ground-water conservation management plan could enable sustainable use of the aquifer. Water-conservation measures and use of alternative sources that water managers in Union County (an area of high demand and growth in Arkansas' initial five-county Critical Ground-Water Area) think to be realistic options result in considerable recovery in water levels in the aquifer during a 30-year model simulation.

Arkansas↗
USGS2009

Assessment of Ground-Water Resources in the Seacoast Region of New Hampshire

Numerical ground-water-flow models were developed for a 160-square-mile area of coastal New Hampshire to provide insight into the recharge, discharge, and availability of ground water. Population growth and increasing water use prompted concern for the sustainability of the region's ground-water resources. Previously, the regional hydraulic characteristics of the fractured bedrock aquifer in the Seacoast region of New Hampshire were not well known. In the current study, the ground-water-flow system was assessed by using two different models developed and calibrated under steady-state seasonal low-flow and transient monthly conditions to ground-water heads and base-flow discharges. The models were, (1) a steady-state model representing current (2003-04) seasonal low-flow conditions used to simulate current and future projected water use during low-flow conditions; and (2) a transient model representing current average and estimated future monthly conditions over a 2-year period used to simulate current and future projected climate-change conditions. The analysis by the ground-water-flow models indicates that the Seacoast aquifer system is a transient flow system with seasonal variations in ground-water flow. A pseudosteady- state condition exists in the fall when the steady-state model was calibrated. The average annual recharge during the period analyzed, 2000-04, was approximately 51 percent of the annual precipitation. The average net monthly recharge rate between 2003 and 2004 varied from 5.5 inches per month in March, to zero in July, and to about 0.3 inches per month in August and September. Recharge normally increases to about 2 inches per month in late fall and early winter (November through December) and declines to about 1.5 inches per month in late winter (January and February). About 50 percent of the annual recharge coincides with snowmelt in the spring (March and April), and 20 percent occurs in the late fall and early winter (November through February). Net recharge, calculated as infiltration of precipitation minus evapotranspiration, can be negative during summer months (particularly July). Regional bulk hydraulic conductivities of the bedrock aquifer were estimated to be about 0.1 to 1.0 feet per day. Estimated hydraulic conductivities in model areas representing the Rye Complex and the Kittery Formation were higher (0.5 to 1 foot per day) than in areas representing the Eliot Formation, the Exeter Diorite, and the Newburyport Complex, which have estimated hydraulic conductivities of 0.1 to 0.2 foot per day. A northeast-southwest regional anisotropy of about 5:1 was estimated in some areas of the model; this pattern is parallel to the regional structural trend and predominant fracture orientation. In areas of the model with more observation data, the upper and lower 95-percent confidence intervals for the estimated bedrock hydraulic conductivity were about half an order of magnitude above and below the parameter, respectively, and the estimated confidence intervals for estimated specific storage were within an order of magnitude of the parameter. In areas of the model with few data points, or few stresses, confidence intervals were several orders of magnitude. Estimated model parameters and their confidence intervals are a function of the conceptual model design, observation data, and the weights placed on the data. The amount of recharge that enters the bedrock aquifer at a specific point depends on (1) the location of the point in the flow field; (2) the hydraulic conductivity of the bedrock (or the connectivity of fractures); and (3) the stresses within the bedrock aquifer. In addition, ground water stored in unconsolidated overburden sediments, including till and other fine-grained sediments, may constitute a large percentage of the water available from storage to the bedrock aquifer. Recharge into the bedrock aquifer at a point can range from zero to nearly all the recharge at the surface dependin

Scientific Investigations Report↗
USGS1984

Annual summary of ground-water conditions in Arizona, spring 1982 to spring 1983

The withdrawal of ground water was slightly less than 4.2 million acre-feet in Arizona in 1982, which is about 1.2 million acre-feet less than the amount withdrawn in 1981. Most of the decrease in 1982 was in the amount of ground water used for irrigation in the Basin and Range lowlands province. Through 1982, slightly more than 193 million acre-feet of ground water had been withdrawn from the ground-water reservoirs in Arizona. The report contains three small-scale maps that show ground-water pumpage by areas, the status of the ground-water inventory and observation-well program, and the ground-water quality sampling program. The main map, which is at a scale of 1:500,000, shows potential well production, depth to water in selected wells in spring 1983, and change in water level in selected wells from 1978 to 1983. A brief text summarizes the current ground-water conditions in the State. (USGS)

Open-File Report↗
USGS2005

Simulation of ground-water flow to assess geohydrologic factors and their effect on source-water areas for bedrock wells in Connecticut

Generic ground-water-flow simulation models show that geohydrologic factors?fracture types, fracture geometry, and surficial materials?affect the size, shape, and location of source-water areas for bedrock wells. In this study, conducted by the U.S. Geological Survey in cooperation with the Connecticut Department of Public Health, ground-water flow was simulated to bedrock wells in three settings?on hilltops and hillsides with no surficial aquifer, in a narrow valley with a surficial aquifer, and in a broad valley with a surficial aquifer?to show how different combinations of geohydrologic factors in different topographic settings affect the dimensions and locations of source-water areas in Connecticut. Three principal types of fractures are present in bedrock in Connecticut?(1) Layer-parallel fractures, which developed as partings along bedding in sedimentary rock and compositional layering or foliation in metamorphic rock (dips of these fractures can be gentle or steep); (2) unroofing joints, which developed as strain-release fractures parallel to the land surface as overlying rock was removed by erosion through geologic time; and (3) cross fractures and joints, which developed as a result of tectonically generated stresses that produced typically near-vertical or steeply dipping fractures. Fracture geometry is defined primarily by the presence or absence of layering in the rock unit, and, if layered, by the angle of dip in the layering. Where layered rocks dip steeply, layer-parallel fracturing generally is dominant; unroofing joints also are typically well developed. Where layered rocks dip gently, layer-parallel fracturing also is dominant, and connections among these fractures are provided only by the cross fractures. In gently dipping rocks, unroofing joints generally do not form as a separate fracture set; instead, strain release from unroofing has occurred along gently dipping layer-parallel fractures, enhancing their aperture. In nonlayered and variably layered rocks, layer-parallel fracturing is absent or poorly developed; fracturing is dominated by well-developed subhorizontal unroofing joints and steeply dipping, tectonically generated fractures and (or) cooling joints. Cross fractures (or cooling joints) in nonlayered and variably layered rocks have more random orientations than in layered rocks. Overall, nonlayered or variably layered rocks do not have a strongly developed fracture direction. Generic ground-water-flow simulation models showed that fracture geometry and other geohydrologic factors affect the dimensions and locations of source-water areas for bedrock wells. In general, source-water areas to wells reflect the direction of ground-water flow, which mimics the land-surface topography. Source-water areas to wells in a hilltop setting were not affected greatly by simulated fracture zones, except for an extensive vertical fracture zone. Source-water areas to wells in a hillside setting were not affected greatly by simulated fracture zones, except for the combination of a subhorizontal fracture zone and low bedrock vertical hydraulic conductivity, as might be the case where an extensive subhorizontal fracture zone is not connected or is poorly connected to the surface through vertical fractures. Source-water areas to wells in a narrow valley setting reflect complex ground-water-flow paths. The typical flow path originates in the uplands and passes through either till or bedrock into the surficial aquifer, although only a small area of the surficial aquifer actually contributes water to the well. Source-water areas in uplands can include substantial areas on both sides of a river. Source-water areas for wells in this setting are affected mainly by the rate of ground-water recharge and by the degree of anisotropy. Source-water areas to wells in a broad valley setting (bedrock with a low angle of dip) are affected greatly by fracture properties. The effect of a given fracture is to channel the

Scientific Investigations Report↗
USGS2006

Microbial Quality of the Nation's Ground-Water Resources, 1993-2004

As part of the National Water-Quality Assessment (NAWQA) program, microbiological data were collected from wells in 22 NAWQA study units during 1993-2004. The wells constituted the sampling networks for three major NAWQA efforts--the major aquifer study, the land-use study, and source-water quality assessments of ground water used for public supplies. Sixteen principal aquifers were represented by these well networks. Samples of untreated ground water were analyzed for concentrations of fecal-indicator bacteria, which included the total-coliform bacteria, fecal-coliform bacteria, and Escherichia coli, and for the presence of somatic and male-specific coliphage viruses. Analyses of the samples showed that coliform bacteria occur relatively frequently-nearly 30 percent of all wells tested positive-and that domestic wells commonly are contaminated by total coliform bacteria, with 33 percent of these wells testing positive. Coliphage viruses were present in 10 percent or fewer of the wells sampled in the Central Columbia Plateau-Yakima, Georgia-Florida, San Joaquin, and Trinity study units, which represent the Columbia Plateau, Floridan, Central Valley, and Coastal Lowlands principal aquifers, respectively. The frequency of detections and concentrations of total coliform bacteria generally were higher in samples from domestic wells than in samples from public-supply wells; in fractured or porous rock materials (carbonate rocks) than in unconsolidated materials (mixtures of sand, gravel, clay); and in principal aquifers with median depths of sampled wells ranging from 100 to 200 feet than in principal aquifers with median depths of sampled wells less than 100 feet or greater than 200 feet. The waters most affected by the presence of coliform bacteria were those in the Valley and Ridge, the Floridan, and the Piedmont and Blue Ridge aquifers, where more than 50 percent of the study wells tested positive for these bacteria. The numbers of wells with detections of coliform bacteria were significantly lower for the Glacial Deposits, Stream and River Valley, Columbia Plateau, Basin and Range, High Plains, Southeastern Coastal Plain, and Coastal Lowlands aquifers. Of the 16 principal aquifers sampled, wells in the Valley and Ridge had the highest overall concentrations of total coliforms, with a median of 2 colony-forming units per 100 milliliters. Elevated concentrations of coliform bacteria (greater than 300 colony-forming units per 100 milliliters) also were reported for wells completed in the Mississippian-Pennsylvanian aquifer and the Ordovician aquifer in lower Tennessee. More than 50 percent of wells completed in carbonate or crystalline rocks tested positive for coliform bacteria. The Floridan, Piedmont and Blue Ridge, Ordovician (lower Tennessee), and Valley and Ridge aquifers are composed of these types of rocks. The lowest detection frequencies (less than 5 percent) were for wells in the Basin and Range and the Snake River aquifers. The materials that constitute these aquifers primarily are unconsolidated sand, gravel, and clay, or basalt with interbeds of sand, gravel, or clay. No strong correlations between concentrations of total coliforms and well depths were identified, nor were there any correlations between total coliform concentrations and selected chemical constituents in the waters. Other factors, such as geohydrologic characteristics, proximity of contaminating sources, interactions with surface water, or well-construction features (including the age of the well), likely control the presence and transport of coliform bacteria in the ground water.

Scientific Investigations Report↗
USGS2000

Quality-assurance design applied to an assessment of agricultural pesticides in ground water from carbonate bedrock aquifers in the Great Valley of eastern Pennsylvania

Assessments to determine whether agricultural pesticides are present in ground water are performed by the Commonwealth of Pennsylvania under the aquifer monitoring provisions of the State Pesticides and Ground Water Strategy. Pennsylvania's Department of Agriculture conducts the monitoring and collects samples; the Department of Environmental Protection (PaDEP) Laboratory analyzes the samples to measure pesticide concentration. To evaluate the quality of the measurements of pesticide concentration for a groundwater assessment, a quality-assurance design was developed and applied to a selected assessment area in Pennsylvania. This report describes the quality-assurance design, describes how and where the design was applied, describes procedures used to collect and analyze samples and to evaluate the results, and summarizes the quality assurance results along with the assessment results. The design was applied in an agricultural area of the Delaware River Basin in Berks, Lebanon, Lehigh, and Northampton Counties to evaluate the bias and variability in laboratory results for pesticides. The design—with random spatial and temporal components—included four data-quality objectives for bias and variability. The spatial design was primary and represented an area comprising 30 sampling cells. A quality-assurance sampling frequency of 20 percent of cells was selected to ensure a sample number of five or more for analysis. Quality-control samples included blanks, spikes, and replicates of laboratory water and spikes, replicates, and 2-lab splits of groundwater. Two analytical laboratories, the PaDEP Laboratory and a U.S. Geological Survey Laboratory, were part of the design. Bias and variability were evaluated by use of data collected from October 1997 through January 1998 for alachlor, atrazine, cyanazine, metolachlor, simazine, pendimethalin, metribuzin, and chlorpyrifos. Results of analyses of field blanks indicate that collection, processing, transport, and laboratory analysis procedures did not contaminate the samples; there were no false-positive results. Pesticides were detected in water when pesticides were spiked into (added to) samples. There were no false negatives for the eight pesticides in all spiked samples. Negative bias was characteristic of analytical results for the eight pesticides, and bias was generally in excess of 10 percent from the ‘true’ or expected concentration (34 of 39 analyses, or 87 percent of the ground-water results) for pesticide concentrations ranging from 0.31 to 0.51 mg/L (micrograms per liter). The magnitude of the negative bias for the eight pesticides, with the exception of cyanazine, would result in reported concentrations commonly 75-80 percent of the expected concentration in the water sample. The bias for cyanazine was negative and within 10 percent of the expected concentration. A comparison of spiked pesticide-concentration recoveries in laboratory water and ground water indicated no effect of the ground-water matrix, and matrix interference was not a source of the negative bias. Results for the laboratory-water spikes submitted in triplicate showed large variability for recoveries of atrazine, cyanazine, and pendimethalin. The relative standard deviation (RSD) was used as a measure of method variability over the course of the study for laboratory waters at a concentration of 0.4 mg/L. An RSD of about 11 percent (or about ?0.05 mg/L)characterizes the method results for alachlor, chlorpyrifos, metolachlor, metribuzin, and simazine. Atrazine and pendimethalin have RSD values of about 17 and 23 percent, respectively. Cyanazine showed the largest RSD at nearly 51 percent. The pesticides with low variability in laboratory-water spikes also had low variability in ground water. The assessment results showed that atrazinewas the most commonly detected pesticide in ground water in the assessment area. Atrazine was detected in water from 22 of the 28 wells sampled, and recovery results for atrazine were some of the worst (largest negative bias). Concentrations of the eight pesticides in ground water from wells were generally less than 0.3 µg/L. Only six individual measurements of the concentrations in water from six of the wells were at or above 0.3 µg/L, five for atrazine and one for metolachlor. There were eight additional detections of metolachlor and simazine at concentrations less than 0.1 µg/L. No well water contained more than one pesticide at concentra-tions at or above 0.3 µg/L. Evidence exists, how-ever, for a pattern of co-occurrence of metolachlor and simazine at low concentrations with higher concentrations of atrazine. Large variability in replicate samples and negative bias for pesticide recovery from spiked samples indicate the need to use data for pesticide recovery in the interpretation of measured pesti-cide concentrations in ground water. Data from samples spiked with known amounts of pesticides were a critical component of a quality-assurance design for the monitoring component of the Pesti-cides and Ground Water Strategy. Trigger concentrations, the concentrations that require action under the Pesticides and Ground Water Strategy, should be considered maximums for action. This consideration is needed because of the magnitude of negative bias.

Water-Resources Investigations Report↗
USGS2002

Ground-water resources of the uppermost confined aquifers, southern Wadena County and parts of Ottertail, Todd, and Cass Counties, central Minnesota, 1997–2000

Water managers are concerned about the increase of ground-water withdrawals from high-capacity wells completed in the uppermost confined aquifers in southern Wadena County. The hydrogeologic units of primary interest in the study area are the surficial aquifer, the uppermost confining units, and the uppermost confined aquifers. The surficial aquifer underlies all but portions of the eastern, western, and south-central parts of the study area, and is as much as 70 ft thick. The thickness of the uppermost confined aquifers ranges from 0 to 72 ft. The thickness of the aquifers is greatest in the south-central and west-central parts of the study area, where thicknesses exceed 50 ft. Depth to the top of the uppermost confined aquifers ranges from 23 to 132 ft. The thickness of the uppermost confining units ranges from 4 to 132 ft. The regional direction of flow in the uppermost confined aquifers is to the east, southeast, and southwest toward the Crow Wing River in the eastern part of the study area and toward the Leaf River in the western part. Sources of water to the uppermost confined aquifers are leakage of water through overlying till and clay and ground-water flow from adjoining aquifers outside the study area. Discharge from the uppermost confined aquifers is by withdrawal from wells and to the surficial aquifer in river valleys. The theoretical maximum well yields for the uppermost confined aquifers range from less that 175 gal/min to greater than 2,000 gal/min and are greatest in areas of greatest aquifer thickness and transmissivity. The water budget for the calibrated steady-state simulation indicated that areal recharge to the surficial aquifer is 86.9 percent of the water to the aquifers, with leakage to the uppermost confined aquifers contributing 6.9 percent. The largest discharges from the aquifers are leakage to streams (54.5 percent) and ground-water evapotranspiration (41.4 percent). The simulated transient water budget for 1999 indicated that the principal sources of water to the aquifers were areal recharge to the surficial aquifer and release from storage. The principal discharges were stream-aquifer leakage, addition to storage, and ground-water evapotranspiration. Results of the steady-state simulation with anticipated increases in ground-water withdrawals indicated maximum drawdowns of 0.3 ft in the surficial aquifer and 0.9 ft in the uppermost confined aquifers due to the anticipated increases in ground-water withdrawals. Model results indicate that the anticipated increases in withdrawals during a drought may lower water levels 2 to 4 ft regionally in much of both the surficial and uppermost confined aquifers. Water-level declines in the surficial aquifer of about 6 ft may occur in Wadena and in the central part of the aquifer south of the Leaf River. Results of the transient simulation indicate that the anticipated increases in withdrawals during a drought would increase seasonal declines in the surficial and uppermost confined aquifers less than 1 and 2 ft, respectively. Model results indicate that greater than anticipated increases in withdrawals during periods of normal precipitation will have minimal effects on ground-water levels and streamflow in the area. In the uppermost confined aquifers, for example, water levels may decline an average of 0.13 ft regionally, with maximum declines of 0.8 to 2.1 ft near Wadena and Verndale. Greater than anticipated increases in withdrawals would cause decreases in ground-water discharge to streams of about 1.4 percent (2.5 ft 3 /s) of 1998-99 steady-state conditions.

Minnesota↗