Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Open Quaternary”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34Linked to original sources

Ground water-surface water relations in the Flathead River valley near the proposed Cabin Creek coal mine, British Columbia, Canada

The area of the proposed Cabin Creek coal mine was studied to obtain information needed to respond to questions posed by the International Joint Commission advisers concerning water resources near the international border. Specific interest focused on determining the extent and character of surficial material in the Flathead River valley, identifying gaining and losing reaches of the river and major tributaries, and documenting ambient water quality at selected sites. Thickness of the alluvial deposits depends on depth to underlaying Quaternary glacial deposits or Tertiary bedrock. The alluvial deposits in the Flathead River valley thin to a veneer of cobbles near the mouth of Couldrey Creek. Measurements of streamflow at 20 sites in the Flathead River valley indicate that water discharges from the alluvial deposits to most of the tributaries and to the river near the proposed mine. The Flathead River gains 0.87 cu m/sec (31 cu ft/sec) of flow near Howell Creek. The Flathead River and Couldrey Creek gained about 0.81 cu m/sec (28.5 cu ft/sec) of flow near the mouth of Couldrey Creek where bedrock crops out in the streambeds. Bedrock outcrops effectively interrupt the alluvial aquifer system between the proposed mine site and the international border. The Flathead River lost 0.87 cu m/sec (31 cu ft/sec) of flow between the bedrock outcrops and the international border; this streamflow loss enters alluvial deposits and flows across the international border as subsurface flow. Analysis of samples from 18 stream sites and 1 spring site indicates general trends in water quality. In Howell Creek, concentrations of calcium, magnesium, and sulfates increased slightly downstream. Conversely, samples from Sage and Couldrey Creeks indicate downstream increases in concentrations of calcium, magnesium, and alkalinity, but decreases in concentrations of sulfate. Water quality of Cabin Creek was relatively stable through the sampled reach. Decreased concentrations of calcium and alkalinity in the Flathead River reflect the effect of inflow from Couldrey Creek and the groundwater inflow documented by streamflow measurements. (Author 's abstract)

Open-File Report↗

Ground water in Minnesota

Ground water is the major source of water supply in Minnesota. The quantity, quality, and availability vary greatly throughout the State. This study describes the State's ground-water resources as found in each of seven major drainage basins. Water is obtained from Quaternary glacial deposits and bedrock aquifers. Most supplies are from the drift except in the southeastern and extreme northeastern parts of the State. In the southeastern part, large quantities of water are withdrawn from sedimentary bedrock aquifers. In the northeastern part, Precambrian igneous and metamorphic rocks underlie the drift and ground-water availability is poor. Large quantities of water are available from surficial outwash, particularly in the central part of the State. Buried outwash aquifers are difficult to locate, delineate, and evaluate. Accordingly, few have been mapped. Water quality in much of the State is suitable for most uses. Ground water is typically hard and high in iron, Water from deep drift and bedrock in the western part of the State is highly mineralized. It may contain excessive amounts of some constituents, such as sodium, chloride, sulfate, boron, and iron. Most ground-water use is centered around cities, the largest amounts being withdrawn in the Minneapolis-St. Paul metropolitan area. Increasing amounts are being used for irrigation, most being obtained from shallow wells in the surficial outwash deposits. Although Minnesota is generally rich in ground-water resources, it is not without associated problems. In the western part of the State, ground-water quality is often a problem, especially in deep aquifers. Throughout the State, few buried outwash aquifers have been delineated or evaluated as to their water-yielding capabilities. Some aquifers are highly susceptible to pollution. Planned development and monitoring of water levels and water quality would be beneficial.

Minnesota↗

Concentrations of selected trace inorganic constituents and synthetic organic compounds in the water-table aquifers in the Memphis area, Tennessee

Water quality samples for analysis of selected trace inorganic constituents and synthetic organic compounds were collected from 29 private or observation wells in alluvium and fluvial deposits of Quaternary and Tertiary Age. The alluvium and fluvial deposits are the water table aquifers in the Memphis area. In addition, nine wells were installed in Memphis Light, Gas and Water Division well fields so that samples could be collected and analyzed to characterize the quality of water in the fluvial deposits at these well fields. Samples from seven of these wells (two were dry) were analyzed for major constituents and properties of water as well as for selected trace inorganic constituents and synthetic organic compounds. Analyses of the water from most of the 36 wells sampled indicated ranges in concentration values for the trace inorganic constituents that agreed with those previously known, although some new maximum values were established. The analysis of water from four wells indicated that the water is or may be contaminated. Concentrations of barium (1,400 micrograms/L -- μg/L), strontium (1,100 μg/L)), and arsenic (15 μg/L), along with specific conductance (1,420 microsiemens/centimeter--us/cm) were in water from one well in the alluvium. Low concentrations (0.02 to 0.04 μg/L) of the pesticides aldrin, DDT, endosulfan, and perthane were present in water from two wells in the fluvial deposits. Water from one of these wells also contained 1,1,1 trichloroethane (4.4 μg/L). Analysis of water from another well in the fluvial deposits indicated values for specific conductance (1,100 μS/cm), alkalinity (508 milligrams per liter -- mg/L -- as CaCO 3 ), hardness (550 mg/L as CaCO 3 ), chloride (65 mg/L), and barium (240 μg/L) that are high for water from the fluvial deposits.

Tennessee↗

Ground-water data as of 1967, Central Coastal Subregion, California

Most usable ground water in the predominantly mountainous Central Coastal Subregion occurs in alluvium-filled valleys and coastal plains and in deeper aquifers of Quaternary and Tertiary age. The intervening mountainous areas are underlain by consolidated sedimentary, igneous, and metamorphic rocks, mainly of Mesozoic age. These older rocks contain only small quantities of recoverable ground water and, therefore, are not considered a major source of ground water. In the Central Coastal Subregion, 24 basins have been identified as significant sources of ground water. The total area of the 24 basins is about 3,500 square miles. The water-bearing deposits range in thickness from about 200 to 4,000 feet. Depending on local conditions, recharge infiltrates at rates of less than 1½ feet per day to more than 10 feet per day in the upper part of alluvial fans and stream channels and at the outcrops of the deeper aquifers. The maximum measured depth to water in the water-bearing deposits is 568 ft. In several valleys there are flowing wells. Total storage capacity of 16 of the basins is more than 20,000,000 acre-feet . The usable storage capacity of 18 of the basins is more than 7,600,000 acre-feet; the limiting factors are sea-water intrusion and high pumping lift. Ground-water temperature ranges from about 55° to about 75°F . The dissolved-solids content of the water is generally less than 800 parts per million, but locally is more than 11,000 parts per million. The predominant water type is calcium bicarbonate, but sodium, magnesium, sulfate, and chloride are present locally in significant quantities. Properly constructed wells in some areas can yield 425 gallons per minute.

California↗

Digital data sets that describe aquifer characteristics of the Rush Springs Aquifer in western Oklahoma

This diskette contains digitized aquifer boundaries and maps of hydraulic conductivity, recharge, and ground-water level elevation contours for the Rush Spring aquifer in western Oklahoma. This area encompasses all or part of Blaine, Caddo, Canadian, Comanche, Custer, Dewey, Grady, Stephens, and Washita Counties. These digital data sets were developed by Mark F. Becker to use as input into a computer model that simulated ground-water flow in the Rush Springs aquifer (Mark F. Becker, U.S. Geological Survey, written commun., 1997). For the purposes of modeling the ground-water flow in the Rush Springs aquifer, Mark F. Becker (written commun., 1997) defined the Rush Springs aquifer to include the Rush Springs Formation, alluvial and terrace deposits along major streams, and parts of the Marlow Formations, particularly in the eastern part of the aquifer boundary area. The Permian-age Rush Springs Formation consists of highly cross-bedded sandstone with some interbedded dolomite and gypsum. The Rush Springs Formation is overlain by Quaternary-age alluvial and terrace deposits that consist of unconsolidated clay, silt, sand, and gravel. The Rush Springs Formation is underlain by the Permian-age Marlow Formation that consists of interbedded sandstones, siltstones, mudstones, gypsum-anhydrite, and dolomite beds (Mark F. Becker, written commun., 1997). The parts of the Marlow Formation that have high permeability and porosity are where the Marlow Formation is included as part of the Rush Springs aquifer. The Rush Springs aquifer underlies about 2,400 square miles of western Oklahoma and is an important source of water for irrigation, livestock, industrial, municipal, and domestic use. Irrigation wells are reported to have well yields greater than 1,000 gallons per minute (Mark F. Becker, written commun., 1997). Mark F. Becker created some of the aquifer boundaries, hydraulic conductivity, and recharge data sets by digitizing parts of previously published surficial geology maps. The hydraulic conductivity and recharge values are the input data to the ground-water flow model (Mark F. Becker, written commun., 1997). The water-level elevation data set was prepared at a scale of 1:250,000 by Mark F. Becker (written commun., 1997) from water levels measured in wells prior to the year 1950. Ground-water flow models are numerical representations that simplify and aggregate natural systems. Models are not unique; different combinations of aquifer characteristics may produce similar results. Therefore, values of hydraulic conductivity and recharge used in the model and presented in this data set are not precise, but are within a reasonable range when compared to independently collected data.

Oklahoma↗

Sediment geochemical records of productivity and oxygen depletion along the margin of western North America during the past 60,000 years: Teleconnections with Greenland Ice and the Cariaco Basin

Many sediment records from the margins of the Californias (Alta and Baja) collected in water depths between 60 and 1200 m contain anoxic intervals (laminated sediments) that can be correlated with interstadial intervals as defined by the oxygen-isotope composition of Greenland ice (Dansgaard–Oeschger, D–O, cycles). These intervals include all or parts of Oxygen Isotope Stage 3 (OIS3; 60–24 cal ka), the Bölling/Alleröd warm interval (B/A; 15–13 cal ka), and the Holocene. This study uses organic carbon (Corg) and trace-element proxies for anoxia and productivity, namely elevated concentrations and accumulation rates of molybdenum and cadmium, in these laminated sediments to suggest that productivity may be more important than ventilation in producing changes in bottom-water oxygen (BWO) conditions on open, highly productive continental margins. The main conclusion from these proxies is that during the last glacial interval (LGI; 24–15 cal ka) and the Younger Dryas cold interval (YD; 13–11.6 cal ka) productivity was lower and BWO levels were higher than during OIS3, the B/A, and the Holocene on all margins of the Californias. The Corg and trace-element profiles in the LGI–B/A–Holocene transition in the Cariaco Basin on the margin of northern Venezuela are remarkably similar to those in the transition on the northern California margin. Correlation between D–O cycles in Greenland ice with gray-scale measurements in varved sediments in the Cariaco Basin also is well established. Synchronous climate-driven changes as recorded in the sediments on the margins of the Californias, sediments from the Cariaco Basin, and in the GISP-2 Greenland ice core support the hypothesis that changes in atmospheric dynamics played a major role in abrupt climate change during the last 60 ka. Millennial-scale cycles in productivity and oxygen depletion on the margins of the Californias demonstrate that the California Current System was poised at a threshold whereby perturbations of atmospheric circulation produced rapid changes in circulation in the eastern North Pacific Ocean. It is likely that the Pacific and Atlantic Oceans were linked through the atmosphere. Warmer air temperatures during interstadials would have strengthened Hadley and Walker circulations, which, in turn, would have strengthened the subtropical high pressure systems in both the North Pacific and the North Atlantic, producing increased rainfall over the Cariaco Basin and increased upwelling along the margins of the Californias.

California↗

A 3-Dimensional Model of Water-Bearing Sequences in the Dominguez Gap Region, Long Beach, California

A 3-dimensional computer model of the Quaternary sequence stratigraphy in the Dominguez gap region of Long Beach, California has been developed to provide a robust chronostratigraphic framework for hydrologic and tectonic studies. The model consists of 13 layers within a 16.5 by 16.1 km (10.25 by 10 mile) square area and extends downward to an altitude of -900 meters (-2952.76 feet). Ten sequences of late Pliocene to Holocene age are identified and correlated within the model. Primary data to build the model comes from five reference core holes, extensive high-resolution seismic data obtained in San Pedro Bay, and logs from several hundred water and oil wells drilled in the region. The model is best constrained in the vicinity of the Dominguez gap seawater intrusion barrier where a dense network of subsurface data exist. The resultant stratigraphic framework and geologic structure differs significantly from what has been proposed in earlier studies. An important new discovery from this approach is the recognition of ongoing tectonic deformation throughout nearly all of Quaternary time that has impacted the geometry and character of the sequences. Anticlinal folding along a NW-SE trend, probably associated with Quaternary reactivation of the Wilmington anticline, has uplifted and thinned deposits along the fold crest, which intersects the Dominguez gap seawater barrier near Pacific Coast Highway. A W-NW trending fault system that approximately parallels the fold crest has also been identified. This fault progressively displaces all but the youngest sequences down to the north and serves as the southern termination of the classic Silverado aquifer. Uplift and erosion of fining-upward paralic sequences along the crest of the young fold has removed or thinned many of the fine-grained beds that serve to protect the underlying Silverado aquifer from seawater contaminated shallow groundwater. As a result of this process, the potential exists for vertical migration of seawater into the producing aquifers and subsequent landward migration of intruded waters beneath the existing Dominguez barrier. Incipient invasion of the Silverado aquifer by chloride-enriched waters is observed in a recently drilled well located along the crest of the fold seaward of the barrier and at a depth of 440 feet (134 meters). These new observations and interpretations indicate that the new sequence-based approach to defining the stratigraphy of the Dominguez Gap area may have important implications for seawater intrusion management. To test this, it will be useful to overlay existing water-quality and water level data onto the framework model and to incorporate the new stratigraphy into a transport model.

Open-File Report↗

Remote sensing and airborne geophysics in the assessment of natural aggregate resources

Natural aggregate made from crushed stone and deposits of sand and gravel is a vital element of the construction industry in the United States. Although natural aggregate is a high volume/low value commodity that is relatively abundant, new sources of aggregate are becoming increasingly difficult to find and develop because of rigid industry specifications, political considerations, development and transporation costs, and environmental concerns, especially in urban growth centers where much of the aggregate is used. As the demand for natural aggregate increases in response to urban growth and the repair and expansion of the national infrastructure, new sources of natural aggregate will be required. The USGS has recognized the necessity of developing the capability to assess the potential for natural aggregate sources on Federal lands; at present, no methodology exists for systematically describing and evaluating potential sources of natural aggregate. Because remote sensing and airborne geophysics can detect surface and nearsurface phenomena, these tools may useful for detecting and mapping potential sources of natural aggregate; however, before a methodology for applying these tools can be developed, it is necessary to understand the type, distribution, physical properties, and characteristics of natural aggregate deposits, as well as the problems that will be encountered in assessing their potential value. There are two primary sources of natural aggregate: (1) exposed or near-surface igneous, metamorphic, and sedimentary bedrock that can be crushed, and (2) deposits of sand and gravel that may be used directly or crushed and sized to meet specifications. In any particular area, the availability of bedrock suitable for crushing is a function of the geologic history of the area - the processes that formed, deformed, eroded and exposed the bedrock. Deposits of sand and gravel are primarily surficial deposits formed by the erosion, transportation by water and ice, and deposition of bedrock fragments. Consequently, most sand and gravel deposits are Tertiary or Quaternary in age and are most common in glaciated areas, alluvial basins, and along rivers and streams. The distribution of potential sources of natural aggregate in the United States is closely tied to physiography and the type of bedrock that occurs in an area. Using these criteria, the United States can be divided into 12 regions: western mountain ranges, alluvial basins, Columbia Plateau, Colorado Plateau and Wyoming basin, High Plains, nonglaciated central region, glaciated central region, Piedmont Blue Ridge region, glaciated northeastern and Superior uplands, Atlantic and Gulf coastal plain, Hawaiian Islands, and Alaska. Each region has similar types of natural aggregate sources within its boundary, although there may be wide variations in specific physical and chemical characteristics of the aggregates within a region. Conventional exploration for natural aggregate deposits has been largely a ground-based operation (field mapping, sampling, trenching and augering, resistivity), although aerial photos and topographic maps have been extensively used to target possible deposits for sampling and testing. Today, the exploration process also considers other factors such as the availability of the land, space and water supply for processing purposes, political and environmental factors, and distance from the market; exploration and planning cannot be separated. There are many physical properties and characteristics by which aggregate material is judged to be acceptable or unacceptable for specific applications; most of these properties and characteristics pertain only to individual aggregate particles and not to the bulk deposit. For example, properties of crushed stone aggregate particles such as thermal volume change, solubility, oxidation and hydration reactivity, and particle strength, among many others, are important consi

Open-File Report↗

Test well DO-CE 88 at Cambridge, Dorchester County, Maryland

Test well DO-CE 88 at Cambridge, Maryland, penetrated 3,299 feet of unconsolidated Quaternary, Tertiary and Cretaceous sediments and bottomed in quartz-monzonite gneiss. The well was drilled to provide data for a study of the aquifer system of the northern Atlantic Coastal Plain. Twenty-one core samples were collected. Six sand zones were tested for aquifer properties and sampled for ground-water chemistry. Point-water heads were measured at seven depths. Environmental heads (which ranged from -18.33 to +44.16 feet relative to sea level) indicate an upward component of flow. A temperature log showed a maximum temperature of 41.9 degrees Celsius and a mean temperature gradient of 0.00838 degrees Celsius per foot. The water analyses delineated the freshwater-saltwater transition zone between 2,650 and 3,100 feet. The ground water changes progressively downward from a sodium bicarbonate to a sodium chloride character. Clays in the analyzed core samples belong to the montmorillonite and kaolinite groups, and mean cation exchange capacity ranged from 8.3 to 38.9 milliequivalents per 100 grams. Vertical and horizontal hydraulic conductivities measured in cores ranged from 1.5 x 10-s to 1.3 feet per day and from 7.3 x 10-6 to 1.3 feet per day, respectively, but the most permeable sands were not cored. Porosity was 1.5 percent in the quartz monzonite bedrock and ranged from 22.4 to 41 percent in the overlying sediments. Transmissivities from aquifer tests ranged from 25 to 850 feet squared per day, horizontal hydraulic conductivities ranged from 2.5 to 85 feet squared per day, and intrinsic permeabilities ranged from 0.8 to 23 micrometers squared. Fossils identified in core samples include palynomorphs, dinoflagellates, and foraminifers.

Maryland↗

Structure and petroleum potential of the continental margin between Cross Sound and Icy Bay, northern Gulf of Alaska

Major structural features of the Yakutat segment, the segment of the continental margin between Cross Sound and Icy Bay, northern Gulf of Alaska, are delineated by multichannel seismic reflection data. A large structural high is centered on Fairweather Ground and lies generally at the edge of the shelf from Cross Sound to west of the Alsek Valley. A basement uplift, the Dangerous River zone, along which the seismic acoustic basement shallows by up to two kilometers, extends north from the western edge of Fairweather Ground towards the mouth of the Dangerous River. The Dangerous River zone separates the Yakutat segment into two distinct subbasins. The eastern subbasin has a maximum sediment thickness of about 4 km, and the axis of the basin is near and parallel to the coast. Strata in this basin are largely of late Cenozoic age (Neogene and Quaternary) and approximately correlate with the onshore Yakataga Formation. The western subbasin has a maximum of at least 9 km of sediment, comprised of a thick (greater than 4.5 km) Paleogene section overlain by late Cenozoic strata. The Paleogene section is truncated along the Dangerous River zone by a combination of erosion, faulting, and onlap onto the acoustic basement. Within the western subbasin, the late Cenozoic basin axis is near and parallel to the coast, but the Paleogene basin axis appears to trend in a northwest direction diagonally across the shelf. Sedimentary strata throughout the Yakutat shelf show regional subsidence and only minor deformation except in the vicinity of the Fairweather Ground structural high, near and along the Dangerous River zone, and at the shoreline near Lituya Bay. Seismic data across the continental slope and adjacent deep ocean show truncation at the continental slope of Paleogene strata, the presence of a thick (to 6 km) undeformed or mildly deformed abyssal sedimentary section at the base of the slope that in part onlaps the slope, and a relatively narrow zone along the slope or at the base of the slope where faulting may have occurred. Observed deformation at the base of the slope is primarily related to the late Cenozoic uplift of Fairweather Ground, and to Quaternary folding perpendicular to the Pacific-North America relative convergence vector. No accretionary section or major deformation is observed along the continental slope. The absence of these features suggests that no major subduction of the Pacific plate beneath the Yakutat margin has occurred during the late Cenozoic. However, transform faulting along the base of the slope has occurred, because probable Oligocene oceanic basement is juxtaposed against Mesozoic and Paleogene sedimentary strata of the Yakutat slope. This juxtaposition most likely occurred during late Oligocene and Miocene time. During much of the late Cenozoic, and especially during Pliocene-Pleistocene time, the Yakutat segment has apparently been moving northward with the Pacific plate. Dredge samples from the continental slope recovered potential hydrocarbon source and reservoir rocks from the Paleogene sedimentary sequence. Most of the organic matter from these samples is immature to marginally mature. Lopatin calculations suggest that rocks beneath the shelf are likely to be thermally mature at a depth of 4 to 5 km and deeper. In general, the strata at these depths are largely of Paleogene age. Thus, the Paleogene strata may have significant resource potential if source and reservoir rocks similar to those dredged at the slope are present below the shelf. The Paleogene strata are contained primarily within the western subbasin; strata in the east subbasin appear to have little resource potential. Structural traps are apparently present in parts of the basin near and along the Dangerous River zone. These traps are in an updip position from potentially mature strata of the western subbasin, and may hold commercial accumulations of hydrocarbons, if sufficient hydrocarbon generation and migration has occurred

Open-File Report↗

Surficial materials of Massachusetts—A 1:24,000-scale geologic map database

The surficial materials geologic map database defines the distribution of nonlithified earth materials at the land surface in the 189 7.5-minute, 1:24,000-scale quadrangles that cover the Commonwealth of Massachusetts (index map). Across the State, these materials range in thickness from a few feet to more than 500 feet (ft). In some places, surficial materials are absent where bedrock is at the land surface. The geologic map database differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics (such as grain size and sedimentary structures), constructional geomorphic features, stratigraphic relationships, and age. The mapped distribution of surficial materials defines the areas of exposed bedrock and the boundaries between glacial till, glacial stratified deposits, and overlying postglacial deposits at a 1:24,000-scale level of accuracy. Most of the surficial materials in Massachusetts are deposits of the last two continental ice sheets that covered all of New England in the latter part of the Pleistocene ice age. The glacial deposits are divided into two broad categories, glacial till and moraine deposits, and glacial stratified deposits. Widespread till deposits were laid down directly on bedrock or on semi-consolidated coastal plain strata by glacier ice. Tills in thick-till (>15 ft thick) drumlin landforms are found in all parts of the State. Areas of shallow bedrock contain thin discontinuous till deposits and numerous bedrock outcrops, and are located chiefly in rocky upland areas. Moraine deposits related to glacial ice lobes of the last ice sheet are located mostly in southeastern Massachusetts. Glacial stratified deposits are concentrated in valleys and lowland areas and were laid down by glacial meltwater in streams, lakes, and the sea in front of the retreating ice margin during the last deglaciation. Postglacial deposits, primarily flood-plain alluvium and swamp deposits, make up a lesser proportion of the unconsolidated materials. The geodatabase included with this report contains MapUnitPolys, MapUnitOverlayPolys, and OverlayPolys, which show the distribution of geologic units that cover the entire map area and are intended for use at quadrangle scale (1:24,000). These data layers can be clipped by quadrangle or by town boundary. Unlike the units in conventional geologic maps, the digitally defined MapUnitOverlayPolys are arranged in order according to superposition. The polygons for till and bedrock are on the bottom and are overlain by the succeeding stratified deposits; these materials are shown everywhere they occur, including beneath postglacial deposits such as swamp deposits, and also beneath water bodies. The postglacial deposits are on top because these materials overlie the other, older deposits. Instructions for using the digital files are included in the README file. A series of map figures in the pamphlet illustrates the stacking of geologic units in a portion of the Mount Toby quadrangle. The BaseMaps folder contains the 1:24,000-scale topographic base map images (1944–1977 editions) used for this compilation. This report supersedes U.S. Geological Survey Open-File Reports 2006-1260-A, -B, -C, -D, -E, -F, -G, and -I.

Massachusetts↗

Implications for the formation of the Hollywood Basin from gravity interpretations of the northern Los Angeles Basin, California

Gravity data provide insights on the complex tectonic history and structural development of the northern Los Angeles Basin region. The Hollywood basin appears to be a long (> 12 km), narrow (up to 2 km wide) trough lying between the Santa Monica Mountains and the Wilshire arch. In the deepest parts of the Hollywood basin, the modeled average thickness ranges from roughly 250 m if filled with only Quaternary sediments to approximately 600 m if Pliocene sediments are also present. Interpretations of conflicting drill hole data force us to consider both these scenarios. Because of the marked density contrast between the dense Santa Monica Mountains and the low-density sediments in the Los Angeles Basin, the gravity method is particularly useful in mapping the maximum displacement along the Santa Monica-Hollywood-Raymond fault zone. The gravity-defined Santa Monica–Hollywood fault zone deviates, in places, from the mapped active fault and fold scarps located with boreholes and trenching and by geomorphological mapping by Dolan and others (1997). Our models suggest that the Santa Monica–Hollywood fault zone dips northward approximately 63°. Three structural models are considered for the origin of the Hollywood basin: pull-apart basin, flexural basin, and a basin related to a back limb of a major fold. Although our preferred structural model involves flexure, the available geologic and geophysical data do not preclude contributions to the deepening of the basin from one or both of the other two models. Of particular interest is that the distribution of red-tagged buildings and structures damaged by the Northridge earthquake has a strong spatial correlation with the axis of the Hollywood basin defined by the gravity data. Several explanations for this correlation are explored, but two preferred geologic factors for the amplification of ground motion besides local site effects are (1) focussing of energy by a fault along the axis of the Hollywood basin and (2) focussing effects related to differential refraction of seismic rays across the basin.

California↗

2007 Rocky Mountain section Friends of the Pleistocene field trip - Quaternary geology of the San Luis basin of Colorado and New Mexico, September 7-9, 2007

Prologue Welcome to the 2007 Rocky Mountain Cell Friends of the Pleistocene Field Trip, which will concentrate on the Quaternary geology of the San Luis Basin of Colorado and New Mexico. To our best knowledge, Friends of the Pleistocene (FOP) has never run a trip through the San Luis Basin, although former trips in the region reviewed the 'Northern Rio Grande rift' in 1987 and the 'Landscape History and Processes on the Pajarito Plateau' in 1996. After nearly a decade, the FOP has returned to the Rio Grande rift, but to an area that has rarely hosted a trip with a Quaternary focus. The objective of FOP trips is to review - in the field - new and exciting research on Quaternary geoscience, typically research being conducted by graduate students. In our case, the research is more topically oriented around three areas of the San Luis Basin, and it is being conducted by a wide range of Federal, State, academic, and consulting geologists. This year's trip is ambitious?we will spend our first day mainly on the Holocene record around Great Sand Dunes National Park and Preserve, the second day on the Quaternary stratigraphy around the San Luis Hills, including evidence for Lake Alamosa and the 1.0 Ma Mesita volcano, and wrap up the trip's third day in the Costilla Plain and Sunshine Valley reviewing alluvial stratigraphy, the history of the Rio Grande, and evidence for young movement on the Sangre de Cristo fault zone. In the tradition of FOP trips, we will be camping along the field trip route for this meeting. On the night before our trip, we will be at the Great Sand Dunes National Park and Preserve's Pinyon Flats Campground, a group facility located about 2 miles north of the Visitors Center. After the first day's trip, we will dine and camp in the Bachus pit, about 3 miles southwest of Alamosa. For the final night (after day 2), we will bed down at La Junta Campground at the Bureau of Land Management (BLM) Wild and Scenic Rivers State Recreation Area, west of Questa, New Mexico, overlooking a majestic canyons of the Rio Grande and Red River. This is the 48th meeting of the Rocky Mountain Section of FOP, which was initiated by Gerry Richmond (USGS-Denver, deceased) in 1952 (see the following table, which lists all the Rocky Mountain Section field trips). The Rocky Mountain Section has been inactive for three years owing to a series of problems, including an unfortunate cancellation of Dennis Dahms' trip to the southern Wind River Range in 2005. Hopefully, this year's trip will provide the logistical initiative and scientific momentum for future Friends of the Pleistocene trips in the Rocky Mountain region.

Colorado, New Mexico↗

Radiocarbon dates from the Hawaiian Islands: A compilation

Radiocarbon dating has proved to be a useful tool for the correlation of events and their timing during the Quaternary. In the Hawaiian Islands, the application of this technique is providing a chronology of the geologic history that will serve as a framework for studies of volcanologic and related hazards, sea-level changes, paleomagnetism, and paleobotany. Many 14 C dates have also been determined for archaeological studies on the Islands. During the last 3 years, the U.S. Geological Survey (USGS) radiocarbon laboratory at Reston, VA, has determined more than 100 14 C dates from carbonized roots and other plant material collected from beneath prehistoric lava flows and ash deposits from Mauna Loa and Kilauea volcanoes. Prior to 1976, only 10 flows from these volcanoes had been dated by radiocarbon methods. Collection of dateable material has been facilitated by an improved understanding of the conditions of charcoal formation and preservation beneath basaltic lavas (Lockwood and Lipman, 1979). The purpose of this report is to gather all published Hawaiian radiocarbon dates, except geochemical dates, together in order to spare those working on the geologic and archaeologic history of the Islands the time and energy necessary to recover these dates from their various sources, as well as to prevent duplication of effort in the field and laboratory. A few unpublished dates from the Reston laboratory are also included. The listing and bibliography are as complete as possible. The U.S. Geological Survey library was used as the primary source of information. The dates are divided by island, and, within island groups, by category of interest. Within each category, dates are listed chronologically from youngest to oldest. The letter before the lab number tells what lab ran the sample. The list of laboratories gives the addresses.

Hawaii↗

Petrology and stratigraphy of Paleogene nonmarine sandstones, Cascade Range, Washington

The Cascade Range of Washington north of 47? latitude is composed of probable Paleozoic and Mesozoic metamorphic rocks and Mesozoic and Tertiary plutonic rocks. Several Paleogene nonmarine arkosic sandstone units fringe and in part occur within the complex crystalline core. The early to middle Eocene Chuckanut Formation is present on the west side of the crystalline core in the western foothills of the Cascades. The early to middle Eocene Swauk Formation partially encircles the Mt. Stuart massif of the central Cascades. In the western foothills of the Cascades, between the main body of Chuckanut Formation near Bellingham and the main outcrop area of the Swauk Formation south of Mt. Stuart, many smaller bodies of arkosic sandstone have variously been referred to either the Swauk or Chuckanut Formations. The early Eocene Manastash Formation occurs locally in an area south of the Yakima River. The middle to late Eocene Chumstick Formation is mostly confined to the Chiwaukum graben within the crystalline core and is separated from the Swauk Formation on the southwest by the Leavenworth Fault. The Oligocene Wenatchee Formation unconformably over lies the Chumstick Formation near Wenatchee. The middle to late Eocene Roslyn Formation crops out north of the Yakima River and is underlain by the Teanaway Basalt which separates the Roslyn from the older Swauk Formation. The middle Eocene to early Oligocene Naches Formation forms a north-trending body that crosses the Yakima River and is in fault contact with both the Swauk and Manastash Formations. The middle to late Eocene Puget Group underlies the Quaternary deposits of the Puget Lowland southeast of Seattle on the western flank of the Cascades. The various formations are all composed predominantly of fine- to medium-grained sandstones with lesser amounts of interbedded shale, conglomerate and coal. Compositionally, the units are predominantly either feldspathic or litho-feldspathic subquartzose sandstones. Volcanic rocks are important constituents of the Puget Group, the Chumstick and Naches Formations, and the isolated arkosic bodies. The three older units, however, contain relatively less volcanic lithics to total lithics than do younger units, indicating perhaps the initiation of more widespread volcanic activity in middle Eocene time. Ratios of framework grain parameters show that the terrestrial sandstone units were derived from a mixed plutonic and tectonic source terrane of continental block tectonic provenance with an overprint of magmatic arc provenance. Modal analysis was performed on samples from the various sedimentary units to establish petrologic compositions, and to provide data with which to compare the different units and discuss clast provenance and tectonic regimen. Although the arkosic sandstones have generally uniform framework clast compositions, minor yet significant differences do exist between the units. Basal or basement-onlap portions of the units in particular are locally derived and differ markedly from the overall compositions of the individual units. Many coincidences of composition, age, structure, and bedrock indicate that the Chuckanut and Swauk may have originally been deposited as a single unit that since has been offset approximately 160 kilometers by right lateral strike slip motion starting about 48 Ma. If this hypothetical offset did occur, then major movement on the Straight Creek Fault is bracketed between about 48 Ma and Oligocene time.

Open-File Report↗

Ground-water resources of Baker Valley, Baker County, Oregon

The Baker Valley is the southern part of a small oval-shaped inter-montane structural basin located near tie southeastern edge of the Blue Mountains of northeastern Oregon. The Powder River enters and leaves the valley through narrow rock gorges. The alluviated basin floor at an altitude of about 3,400 feet is bounded by high, Alpine-type mountains on the west and by lover hilly ridges on the north, east, and south. Creeks descend across alluvial fans from the higher western margin of the valley to the Powder River on the valley floor. The valley floor and the contiguous alluvial slopes are formed of unconsolidated deposits of Quaternary age having a thickness of more than 700 feet in the central part of the valley. The surrounding higher lands are formed of consolidated rocks composed of volcanic flows, tuffs, and partly consolidated deposits of Tertiary age, and sedimentary, igneous, and metamorphic roots of late Paleozoic age. The unconsolidated materials underlying the alluvial slopes are mostly fanglomerates - composed of partly consolidated angular rock fragments imbedded in assorted finer materials - and fine-grained sedimentary deposits having much inter-bedded gravel and sand along the valley floor. The unconsolidated deposits contain a body of ground water, the upper surface of which is called the water table. The water table slopes down gradient approximately parallel to tile land surface. Variations in the general inclination of that water table indicate that drainage on different segments of the alluvial slope is influent and effluent to the ground water body. Yields from wells in the fanglomerate along the rest side of the valley are not large, but large yields are obtained from wells on the valley floor just north of Baker. Properly constructed test wells have not been drilled over much of the northern part of the valley floor. The Tertiary rocks of both volcanic and sedimentary origin along the margin of the valley east of Baker contain some ground water under sufficient pressure to cause wells to flow at the surface, but generally those strata are not highly productive. Some water occurring along fault lines in these rocks has all abnormally high temperature. The growing season in this area is short and the use of shallow water for irrigation may aid materially in securing the maximum returns of which the valley is capable.

Oregon↗

Geology of Precambrian rocks and isotope geochemistry of shear zones in the Big Narrows area, northern Front Range, Colorado

Rocks within the Big Narrows and Poudre Park quadrangles located in the northern Front Range of Colorado are Precambrian metasedimentary and metaigneous schists and gneisses and plutonic igneous rocks. These are locally mantled by extensive late Tertiary and Quaternary fluvial gravels. The southern boundary of the Log Cabin batholith lies within the area studied. A detailed chronology of polyphase deformation, metamorphism and plutonism has been established. Early isoclinal folding (F1) was followed by a major period of plastic deformation (F2), sillimanite-microcline grade regional metamorphism, migmatization and synkinematic Boulder Creek granodiorite plutonism (1.7 b.y.). Macroscopic doubly plunging antiformal and synformal structures were developed. P-T conditions at the peak of metamorphism were probably about 670?C and 4.5 Kb. Water pressures may locally have differed from load pressures. The 1.4 b.y. Silver Plume granite plutonism was post kinematic and on the basis of petrographic and field criteria can be divided into three facies. Emplacement was by forcible injection and assimilation. Microscopic and mesoscopic folds which postdate the formation of the characteristic mineral phases during the 1.7 b.y. metamorphism are correlated with the emplacement of the Silver Plume Log Cabin batholith. Extensive retrograde metamorphism was associated with this event. A major period of mylonitization postdates Silver Plume plutonism and produced large E-W and NE trending shear zones. A detailed study of the Rb/Sr isotope geochemistry of the layered mylonites demonstrated that the mylonitization and associated re- crystallization homogenized the Rb87/Sr 86 ratios. Whole-rock dating techniques applied to the layered mylonites indicate a probable age of 1.2 b.y. Petrographic studies suggest that the mylonitization-recrystallization process produced hornfels facies assemblages in the adjacent metasediments. Minor Laramide faulting, mineralization and igneous activity occurred within this area. A sinuous band of gravel deposits trending into the Livermore embayment and lying well above the present drainage is believed to represent a late Tertiary course of the Cache La Poudre river.

Open-File Report↗

Seismic hazard study of the western portion of the Garlock fault [California]

Investigations of the western segment of the Garlock fault were conducted at Castac Lake, Twin Lakes and Oak Creek Canyon. Studies were concentrated on the youngest fault trace as delineated by Clark (1973). Seismic refraction surveys, topographic surveys and geologic mapping provided positive evidence for fault offsets in Quaternary deposits at Twin Lakes and Oak Creek Canyon. Investigations at Castac Lake were concentrated on the fault segment north of the lake. Previous investigations south of the lake and across the dry lake bottom exposed unbroken strata dating back 8050 +300 years B.P. No evidence of offset of young deposits was found north of the lake from surface investigations or seismic refraction data. Trenching of sag pond deposits at Twin Lakes revealed fault traces representing 2 events confined to a zone 3 meters wide. The stratigraphy at Twin Lakes consists of alternating units of clay and sand allowing measurements of vertical offsets. Based on radiocarbon dates of detrital charcoal, the most recent movement occurred less than 890 +195 years B.P. and the proceeding event occurred greater than 2,800 +165 years B.P. Total vertical offset was 80 to 100 cm for the most recent movement and 55-60 cm for the proceeding event. Geomorphic analysis of offset alluvial stream channels at Oak Creek Canyon provided an estimate of 1.6 to 3.3 mm per year of left lateral movement during Holocene and late Pleistocene times. This estimate is based on correlation of soil profile development with dated soil stratigraphy in the San Joaquin Valley. Scarp heights and lack of definitive evidence for recent left-lateral offset in Oak Creek Canyon indicates a significant and perhaps predominant vertical component of movement with: 1) a comparatively long recurrence interval and/or 2) a small component of left-lateral movement. Arching of late Pleistocene deposits in Oak Creek Canyon is consistent with right-lateral rather than left-lateral wrench faulting, suggesting a fluctuation in stresses along this part of the fault since late Pleistocene time.

Open-File Report↗