Results for “Internal Report” — Page 29

USGS1992

Map showing sediment isopachs in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗

USGS1992

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗

USGS2011

Report on the 2010 Chilean earthquake and tsunami response

In July 2010, in an effort to reduce future catastrophic natural disaster losses for California, the American Red Cross coordinated and sent a delegation of 20 multidisciplinary experts on earthquake response and recovery to Chile. The primary goal was to understand how the Chilean society and relevant organizations responded to the magnitude 8.8 Maule earthquake that struck the region on February 27, 2010, as well as how an application of these lessons could better prepare California communities, response partners and state emergency partners for a comparable situation. Similarities in building codes, socioeconomic conditions, and broad extent of the strong shaking make the Chilean earthquake a very close analog to the impact of future great earthquakes on California. To withstand and recover from natural and human-caused disasters, it is essential for citizens and communities to work together to anticipate threats, limit effects, and rapidly restore functionality after a crisis. The delegation was hosted by the Chilean Red Cross and received extensive briefings from both national and local Red Cross officials. During nine days in Chile, the delegation also met with officials at the national, regional, and local government levels. Technical briefings were received from the President’s Emergency Committee, emergency managers from ONEMI (comparable to FEMA), structural engineers, a seismologist, hospital administrators, firefighters, and the United Nations team in Chile. Cities visited include Santiago, Talca, Constitución, Concepción, Talcahuano, Tumbes, and Cauquenes. The American Red Cross Multidisciplinary Team consisted of subject matter experts, who carried out special investigations in five Teams on the (1) science and engineering findings, (2) medical services, (3) emergency services, (4) volunteer management, and (5) executive and management issues (see appendix A for a full list of participants and their titles and teams). While developing this delegation, it was clear that a multidisciplinary approach was required to properly analyze the emergency response, technical, and social components of this disaster. A diverse and knowledgeable delegation was necessary to analyze the Chilean response in a way that would be beneficial to preparedness in California, as well as improve mitigation efforts around the United States. By most standards, the Maule earthquake was a catastrophe for Chile. The economic losses totaled $30 billion USD or 17% of the GDP of the country. Twelve million people, or ¾ of the population of the country, were in areas that felt strong shaking. Yet only 521 fatalities have been confirmed, with 56 people still missing and presumed dead in the tsunami. The Science and Technology Team evaluated the impacts of the earthquake on built environment with implications for the United States. The fires following the earthquake were minimal in part because of the shutdown of the national electrical grid early in the shaking. Only five engineer-designed buildings were destroyed during the earthquake; however, over 350,000 housing units were destroyed. Chile has a law that holds building owners liable for the first 10 years of a building’s existence for any losses resulting from inadequate application of the building code during construction. This law was cited by many our team met with as a prime reason for the strong performance of the built environment. Overall, this earthquake demonstrated that strict building codes and standards could greatly reduce losses in even the largest earthquakes. In the immediate response to the earthquake and tsunami, first responders, emergency personnel, and search and rescue teams handled many challenges. Loss of communications was significant; many lives were lost and effective coordination to support life-sustaining efforts was gravely impacted due to a lack of inter- and intra-agency coordination. The Health and Medical Services Team sought to understand the medical disaster response strategies and operations of Chilean agencies, including perceived or actual failures in disaster preparation that impacted the medical disaster response; post-disaster health and medical interventions to save lives and limit suffering; and the lessons learned by public health and medical personnel as a result of their experiences. Despite devastating damage to the health care and civic infrastructure, the health care response to the Chilean earthquake appeared highly successful due to several factors. Like other first responders, the medical community had the ability and resourcefulness to respond without centralized control in the early response phase. The health care community maintained patient care under austere conditions, despite many obstacles that could have prevented such care. National and international resources were rapidly mobilized to support the medical response. The Emergency Services Team sought to collect information on all phases of emergency management (preparedness, mitigation, response, and recovery) and determine what worked well and what could be improved upon. The Chileans reported being surprised that they were not as ready for this event as they thought they were. The use of mass care sheltering was limited, given the scope of the disaster, because of the resiliency of the population. The impacts of the earthquake and the tsunami were quite different, as were the needs of urban and rural dwellers, necessitating different response activities. The Volunteer Services Team examined the challenges faced in mobilizing a large number of volunteers to assist in the aftermath of a disaster of this scale. One of the greatest challenges expressed was difficulty in communication; the need for redundancy in communication mechanisms was cited. The flexibility and ability to work autonomously by the frontline volunteers was a significant factor in effective response. It was also important for volunteer leadership to know the emergency plans. These plans need to be flexible, include alternative options, and be completed in conjunction with local officials and other volunteers. The Executive/Red Cross Management Team took a broad look at the impacts of the earthquake and the implications for California. Some of the most important preparation for the disaster came from relationships formed before the event. The communities with strong connections between different government services generally fared well. The initial response and resilience of individuals and communities was another important component. Communication system failures limited the ability of a central government to assist impacted communities, or to issue tsunami warnings. It also delayed the response since the government did not know (in some case for several days) the impact and needs of local governments. In general, plans for congregate care shelters existed but were little used as most people chose to stay at damaged homes or with relatives. Looting was a surprise to response officials as well as social scientists, but both public and private sector organizations, including NGOs (Non-Governmental Organizations), must consider security for damaged businesses as a priority in California’s multihazard planning. Class and ethnic divisions that become heightened during some cases of actual or perceived injustice may also emerge in natural disasters in California. Several factors contributed overall to the low casualty rate and rapid recovery. A major factor is the strong building code in Chile and its comprehensive enforcement. In particular, Chile has a law that holds building owners accountable for losses in a building they build for 10 years. A second factor was the limited number of fires after the earthquake. In the last few California earthquakes, 60% of the fires were started by electrical problems, so the rarity of fires may have been affected by the shut down of the electricity grid early in the earthquake. Third, in many areas, the local emergency response was very effective. The most effective regions had close coordination between emergency management, fire, and police and were empowered to respond without communication with the capital. The fourth factor was the overall high level of knowledge about earthquakes and tsunamis by much of the population that helped them respond more appropriately after the event.

Open-File Report↗

USGS2014

Elders recall an earlier tsunami on Indian Ocean shores

Ten years on, the Indian Ocean tsunami of 26 December 2004 still looms large in efforts to reduce coastal risk. The disaster has spurred worldwide advances in tsunami detection and warning, tsunami-risk assessment, and tsunami awareness [Satake, 2014]. Nearly a lifetime has passed since the northwestern Indian Ocean last produced a devastating tsunami. Documentation of this tsunami, in November 1945, was hindered by international instability in the wake of the Second World War and, in British India, by the approach of independence and partition. The parent earthquake, of magnitude 8.1, was widely recorded, and the tsunami registered on tide gauges, but intelligence reports and newspaper articles say little about inundation limits while permitting a broad range of catalogued death tolls. What has been established about the 1945 tsunami falls short of what's needed today for ground-truthing inundation models, estimating risk to enlarged populations, and anchoring awareness campaigns in local facts. Recent efforts to reduce coastal risk around the Arabian Sea include a project in which eyewitnesses to the 1945 tsunami were found and interviewed (Fig. 1), and related archives were gathered. Results are being made available through UNESCO's Indian Ocean Tsunami Information Center in hopes of increasing scientific understanding and public awareness of the region's tsunami hazards.

Eos, Earth and Space Science News↗

USGS2013

Hydrographic surveys of four narrows within the Namakan reservoir system, Voyageurs National Park, Minnesota, 2011

The U.S. Geological Survey performed multibeam echosounder hydrographic surveys of four narrows in the Namakan reservoir system in August 2011, in cooperation with the International Joint Commission and Environment Canada. The data-collection effort was completed to provide updated and detailed hydrographic data to Environment Canada for inclusion in a Hydrologic Engineering Centers River Analysis System hydraulic model. The Namakan reservoir system is composed of Namakan, Kabetogama, Sand Point, Crane, and Little Vermilion Lakes. Water elevations in the Namakan reservoir system are regulated according to rule curves, or guidelines for water-level management based on the time of year, established by the International Joint Commission. Water levels are monitored by established gages on Crane Lake and the outlet of Namakan Lake at Kettle Falls, but water elevations throughout the system may deviate from these measured values by as much as 0.3 meters, according to lake managers and residents. Deviations from expected water elevations may be caused by between-lake constrictions (narrows). According to the 2000 Rule Curve Assessment Workgroup, hydrologic models of the reservoir system are needed to better understand the system and to evaluate the recent changes made to rule curves in 2000. Hydrographic surveys were performed using a RESON SeaBat™7125 multibeam echosounder system. Surveys were completed at Namakan Narrows, Harrison Narrows, King Williams Narrows, and Little Vermilion Narrows. Hydrographic survey data were processed using Caris HIPS TM and SIPS TM software that interpolated a combined uncertainty and bathymetric estimator (CUBE) surface. Quality of the survey results was evaluated in relation to standards set by the International Hydrographic Organization (IHO) for describing the uncertainty of hydrographic surveys. More than 90 percent of the surveyed areas at the four narrows have resulting bed elevations that meet the IHO “Special Order” quality. Survey datasets published in this report are formatted as text files of x-y-z coordinates and as CARIS Spatial Archive TM (CSAR TM ) files with corresponding metadata.

Minnesota↗

USGS2010

Guidelines for Standardized Testing of Broadband Seismometers and Accelerometers

Testing and specification of seismic and earthquake-engineering sensors and recorders has been marked by significant variations in procedures and selected parameters. These variations cause difficulty in comparing such specifications and test results. In July 1989, and again in May 2005, the U.S. Geological Survey hosted international pub-lic/private workshops with the goal of defining widely accepted guidelines for the testing of seismological inertial sensors, seismometers, and accelerometers. The Proceedings of the 2005 workshop have been published and include as appendix 6 the report of the 1989 workshop. This document represents a collation and rationalization of a single set of formal guidelines for testing and specifying broadband seismometers and accelerometers.

Open-File Report↗

USGS1977

Summary of hydrologic data collected during 1975 in Dade County, Florida

During the 1975 calendar year rainfall in Dade County, Fla., was 14.89 inches below the long-term average (57.17 in.). Ground-water levels ranged from 0.1 foot above to 1.1 feet below average. The highest and lowest ground-water levels for the year were both 1 foot below their long-term averages. In the Hialeah-Miami Springs area, ground-water levels in wells near the centers of the heaviest pumping ranged from 9.8 to 11.2 feet below mean sea level and in the Southwest well field area, ground-water levels near the centers of pumping ranged from 3.5 feet above to 3.4 feet below mean sea level. The combined average daily discharge from eight major streams and canals that flow into Biscayne Bay was 1,014 cubic feet per second (cfs), 124 cfs above the combined average daily flow for the 1974 water year. The combined average daily flow through the Tamiami Canal outlets was 568 cfs, 202 cfs below that of the 1974 water year. The position of the salt front in 1975 in the coastal part of the Biscayne aquifer was about the same as in 1974 except at Miami International Airport and Homestead Air Force Base where the salt front had encroached farther inland. (Woodard-USGS)

Open-File Report↗

USGS1972

A geochemical study of the Rio Pantanos area, Department of Antioquia, Colombia preliminary report

Geochemical sampling in the Western Cordillera has delineated an 18 km 2 area anomalous in copper, molybdenum, and silver. Highly anomalous metal contents are found in stream sediment, soil, and outcrop samples collected within this area. The area is underlain by intrusive granodiorite to quartz diorite that has porphyritic and granitoid phases. Most of the outcrop samples contain disseminated pyrite, chalcopyrite, and bornite. A geochemical reconnaissance sampling program in the Western Cordillera, formulated by Andros Jimeno V., Director, Instituto National de Investigaciones Geologico-Mineras (INGEOMINAS), and Earl M. Irving, U. S. Geological Survey (USGS) Chief of Party in Colombia, was carried out from 1969 to 1971 by geologists of the INGEOMINAS office in Medellin. This work was part of a cooperative program of INGEOMINAS and the USGS sponsored by the Government of Colombia and the Agency for International Development, U. S. Department of State. Seventeen generally east-trending traverses were completed across the Western Cordillera. These traverses, generally paralleling major drainages, cross the range at intervals of 10 to 30 km.

Open-File Report↗

USGS2018

External quality assurance project report for the National Atmospheric Deposition Program’s National Trends Network and Mercury Deposition Network, 2015–16

The U.S. Geological Survey Precipitation Chemistry Quality Assurance project operated five distinct programs to provide external quality assurance monitoring for the National Atmospheric Deposition Program’s (NADP) National Trends Network and Mercury Deposition Network during 2015–16. The National Trends Network programs include (1) a field audit program to evaluate sample contamination and stability, (2) an interlaboratory comparison program to evaluate analytical laboratory performance, and (3) a colocated sampler program to evaluate bias and variability attributed to automated precipitation samplers. The Mercury Deposition Network programs include the (4) system blank program and (5) an interlaboratory comparison program. The results indicate that NADP data continue to be of sufficient quality for the analysis of spatial distributions and time trends for chemical constituents in wet deposition. The field audit program results indicate increased sample contamination for calcium, magnesium, and potassium relative to 2010 levels, and slight fluctuation in sodium contamination. Nitrate contamination levels dropped slightly during 2014–16, and chloride contamination leveled off between 2007 and 2016. Sulfate contamination is similar to the 2000 level. Hydrogen ion contamination has steadily decreased since 2012. Losses of ammonium and nitrate resulting from potential sample instability were negligible. The NADP Central Analytical Laboratory produced interlaboratory comparison results with low bias and variability compared to other domestic and international laboratories that support atmospheric deposition monitoring. Significant absolute bias above the magnitudes of the detection limits was observed for nitrate and sulfate concentrations, but no analyte determinations exceeded the detection limits for blanks. Colocated sampler program results from dissimilar colocated collectors indicate that the retrofit of the National Trends Network with N-CON Systems Company, Inc. precipitation collectors could cause substantial shifts in NADP annual deposition (concentration multiplied by depth) values. Median weekly relative percent differences for analyte concentrations ranged from -4 to +76 percent for cations, from 5 to 6 percent for ammonium, from +14 to +25 percent for anions, and from -21 to +8 percent for hydrogen ion contamination. By comparison, weekly absolute concentration differences for paired identical N-CON Systems Company, Inc., collectors ranged from 4–22 percent for cations; 2–9 percent for anions; 4–5 percent for ammonium; and 13–14 percent for hydrogen ion contamination. The N-CON Systems Company, Inc. collector caught more precipitation than the Aerochem Metrics Model 301 collector (ACM) at the WA99/99WA sites, but it typically caught slightly less precipitation than the ACM at ND11/11ND, sites which receive more wind and snow than WA99/99WA. Paired, identical OTT Pluvio-2 and ETI Noah IV precipitation gages were operated at the same sites. Median absolute percent differences for daily measured precipitation depths ranged from 0 to 7 percent. Annual absolute differences ranged from 0.08 percent (ETI Noah IV precipitation gages) to 11 percent (OTT Pluvio-2 precipitation gages). The Mercury Deposition Network programs include the system blank program and an interlaboratory comparison program. System blank results indicate that maximum total mercury contamination concentrations in samples were less than the third percentile of all Mercury Deposition Network sample concentrations (1.098 nanograms per liter; ng/L). The Mercury Analytical Laboratory produced chemical concentration results with low bias and variability compared with other domestic and international laboratories that support atmospheric-deposition monitoring. The laboratory’s performance results indicate a +1-ng/L shift in bias between 2015 (-0.4 ng/L) and 2016 (+0.5 ng/L).

Scientific Investigations Report↗

USGS1996

Hydrogeology and steady-state simulation of ground-water flow in the San Juan Basin, New Mexico, Colorado, Arizona, and Utah

As part of a multidisciplinary regional aquifer-system analysis, a three-dimensional steady-state ground-water-flow model was constructed for the San Juan Basin in parts of New Mexico, Colorado, Arizona, and Utah. The model simulated ground- water flow in 12 hydrostratigraphic units representing all of the major sources of ground water from aquifers of Jurassic and younger age. Ten map reports in the U.S. Geological Survey Hydrologic Investigations Atlas 720 series were prepared in conjunction with this investigation. The units that were described in the atlases were the San Jose, Nacimiento, and Animas Formations; Ojo Alamo Sandstone; Kirtland Shale and Fruitland Formation; Pictured Cliffs Sandstone; Cliff House Sandstone; Menefee Formation; Point Lookout Sandstone; Gallup Sandstone; Dakota Sandstone; and Morrison Formation. Additional descriptions of the alluvial and landslide deposits, Chuska and Crevasse Canyon Sandstones, Lewis and Mancos Shales, Wanakah Formation, and Entrada Sandstone are included in this report. Much of the information in the HA-720 series was generated from digital computer data bases that were directly usable by the computer for compilation of input data for the model. In essence, the major components of the ground-water- flow model were described and documented in the series of hydrologic atlases. The primary finding resulting from the ground-water-flow simulation was that boundary conditions and internal geometry of the aquifers are the major controls of steady-state ground-water flow and hydraulic heads in the San Juan Basin. Another significant finding was that the computed steady-state ground- water flux is a very minor component (about 1 percent) of the total water budget of the basin.

Water-Resources Investigations Report↗

USGS1891

Altitudes between Lake Superior and the Rocky Mountains

In the survey of Lake Agassiz, a preliminary report of which forms Bulletin No. 39, it was found necessary to ascertain the altitudes determined within its area by railroad surveys as the basis for leveling along the shore lines of that glacial lake, and learning their relations in height to each other, to the great lakes of the St. Lawrence and Nelson Rivers, and to the ocean. From the time of the first observations and description of the upper beaches of Lake Agassiz by the author in 1879 and 1881, for the Geological Survey of Minnesota, and especially since the work was extended in 1885, under the U. S. Geological Survey, to include both sides of this lacustrine area in Minnesota and North Dakota now drained by the Red River of the North, much attention has been given to this collection of altitudes, and to the means of referring them to the sea level. The greater part of Lake Agassiz, however, was in Manitoba and adjacent British Territory, stretching north to the Saskatchewan; and in 1887, jointly for the Geological Surveys of the United States and of Canada, the author continued his examination of the beaches and deltas on the west side of the lake along a distance of a hundred miles north from the international boundary, across the prairie region of southwestern Manitoba, the leveling in this work being based on the altitudes of the Canadian Pacific Railway and its branches and connecting railways.

Bulletin↗

USGS2019

Asian swamp eels in North America linked to the live-food trade and prayer-release rituals

We provide a history of swamp eel (family Synbranchidae) introductions around the globe and report the first confirmed nonindigenous records of Amphipnous cuchia in the wild. The species, native to Asia, is documented from five sites in the USA: the Passaic River, New Jersey (2007), Lake Needwood, Maryland (2014), a stream in Pennsylvania (2015), the Tittabawassee River, Michigan (2017), and Meadow Lake, New York (2017). The international live-food trade constitutes the major introduction pathway, a conclusion based on: (1) United States Fish and Wildlife Service’s Law Enforcement Management Information System (LEMIS) database records revealing regular swamp eel imports from Asia since at least the mid-1990s; (2) surveys (2001–2018) documenting widespread distribution of live A. cuchia among ethnic food markets in the USA and Canada; (3) indications that food markets are the only source of live A. cuchia in North America; and (4) presence of live A. cuchia in markets close to introduction sites. Prayer release appears to be an important pathway component, whereby religious practitioners purchase live A. cuchia from markets and set them free. Prevalence of A. cuchia in US markets since 2001 indicates the species is the principal swamp eel imported, largely replacing members of the Asian complex Monopterus albus/javanensis. LEMIS records (July 1996–January 2017) document 972 shipments containing an estimated 832,897 live swamp eels entering the USA, although these data underestimate actual numbers due to undeclared and false reporting. LEMIS data reveal most imports originate in Bangladesh, Vietnam, and China. However, LEMIS wrongly identifies many imported swamp eels as “Monopterus albus”; none are identified as A. cuchia although specimens from Bangladesh and India are almost certainly this species. Some imported A. cuchia are erroneously declared on import forms as Anguilla bengalensis. To date, there is no evidence of A. cuchia reproduction in open waters of North America, presumably because it is a tropical-subtropical species and all introductions thus far have been in latitudes where winter water temperatures regularly fall near or below freezing.

Aquatic Invasions↗

USGS2016

New organic reference materials for hydrogen, carbon, and nitrogen stable isotope-ratio measurements: caffeines, n-alkanes, fatty acid methyl esters, glycines, L-valines, polyethylenes, and oils

An international project developed, quality-tested, and determined isotope−δ values of 19 new organic reference materials (RMs) for hydrogen, carbon, and nitrogen stable isotope-ratio measurements, in addition to analyzing pre-existing RMs NBS 22 (oil), IAEA-CH-7 (polyethylene foil), and IAEA-600 (caffeine). These new RMs enable users to normalize measurements of samples to isotope−δ scales. The RMs span a range of δ 2 H VSMOW-SLAP values from −210.8 to +397.0 mUr or ‰, for δ 13 C VPDB-LSVEC from −40.81 to +0.49 mUr and for δ 15 N Air from −5.21 to +61.53 mUr. Many of the new RMs are amenable to gas and liquid chromatography. The RMs include triads of isotopically contrasting caffeines, C 16 n -alkanes, n -C 20 -fatty acid methyl esters (FAMEs), glycines, and l -valines, together with polyethylene powder and string, one n -C 17 -FAME, a vacuum oil (NBS 22a) to replace NBS 22 oil, and a 2 H-enriched vacuum oil. A total of 11 laboratories from 7 countries used multiple analytical approaches and instrumentation for 2-point isotopic normalization against international primary measurement standards. The use of reference waters in silver tubes allowed direct normalization of δ 2 H values of organic materials against isotopic reference waters following the principle of identical treatment. Bayesian statistical analysis yielded the mean values reported here. New RMs are numbered from USGS61 through USGS78, in addition to NBS 22a. Because of exchangeable hydrogen, amino acid RMs currently are recommended only for carbon- and nitrogen-isotope measurements. Some amino acids contain 13 C and carbon-bound organic 2 H-enrichments at different molecular sites to provide RMs for potential site-specific isotopic analysis in future studies.

Analytical Chemistry↗

USGS2008

Physical properties of repressurized samples recovered during the 2006 National Gas Hydrate Program expedition offshore India

As part of an international cooperative research program, the U.S. Geological Survey (USGS) and researchers from the National Gas Hydrate Program (NGHP) of India are studying the physical properties of sediment recovered during the NGHP-01 cruise conducted offshore India during 2006. Here we report on index property, acoustic velocity, and triaxial shear test results for samples recovered from the Krishna-Godavari Basin. In addition, we discuss the effects of sample storage temperature, handling, and change in structure of fine-grained sediment. Although complex, sub-vertical planar gas-hydrate structures were observed in the silty clay to clayey silt samples prior to entering the Gas Hydrate And Sediment Test Laboratory Instrument (GHASTLI), the samples yielded little gas post test. This suggests most, if not all, gas hydrate dissociated during sample transfer. Mechanical properties of hydrate-bearing marine sediment are best measured by avoiding sample depressurization. By contrast, mechanical properties of hydrate-free sediments, that are shipped and stored at atmospheric pressure can be approximated by consolidating core material to the original in situ effective stress.

Conference Paper↗

USGS2011

Usage and administration manual for a geodatabase compendium of water-resources data: Rio Grande Basin from the Rio Arriba-Sandoval County line, New Mexico, to Presidio, Texas, 1889-2009

The U.S. Geological Survey, in cooperation with the New Mexico Interstate Stream Commission, developed a geodatabase compendium (hereinafter referred to as the 'geodatabase') of available water-resources data for the reach of the Rio Grande from Rio Arriba-Sandoval County line, New Mexico, to Presidio, Texas. Since 1889, a wealth of water-resources data has been collected in the Rio Grande Basin from Rio Arriba-Sandoval County line, New Mexico, to Presidio, Texas, for a variety of purposes. Collecting agencies, researchers, and organizations have included the U.S. Geological Survey, Bureau of Reclamation, International Boundary and Water Commission, State agencies, irrigation districts, municipal water utilities, universities, and other entities. About 1,750 data records were recently (2010) evaluated to enhance their usability by compiling them into a single geospatial relational database (geodatabase). This report is intended as a user's manual and administration guide for the geodatabase. All data available, including water quality, water level, and discharge data (both instantaneous and daily) from January 1, 1889, through December 17, 2009, were compiled for the study area. A flexible and efficient geodatabase design was used, enhancing the ability of the geodatabase to handle data from diverse sources and helping to ensure sustainability of the geodatabase with long-term maintenance. Geodatabase tables include daily data values, site locations and information, sample event information, and parameters, as well as data sources and collecting agencies. The end products of this effort are a comprehensive water-resources geodatabase that enables the visualization of primary sampling sites for surface discharges, groundwater elevations, and water-quality and associated data for the study area. In addition, repeatable data processing scripts, Structured Query Language queries for loading prepared data sources, and a detailed process for refreshing all data in the compendium have been developed. The geodatabase functionality allows users to explore spatial characteristics of the data, conduct spatial analyses, and pose questions to the geodatabase in the form of queries. Users can also customize and extend the geodatabase, combine it with other databases, or use the geodatabase design for other water-resources applications.

New Mexico, Texas↗

USGS1978

Intrusive rocks northeast of Steamboat Springs, Park Range, Colorado

Major Precambrian and minor Tertiary intrusive rocks northeast of Steamboat Springs in the Park Range between 40°30' and 40°45' N. lat. are described and compared with related rocks elsewhere in Colorado and Wyoming. The Precambrian intrusives were emplaced in a sequence of high-grade interlayered felsic gneisses, amphibolites, and pelitic schists of sedimentary and volcanic origin. These rocks are cut by a major northeast-trending Precambrian shear zone where mainly left lateral movement of 1/ 2 to 1 mile is certain. Cumulative movement of many miles is possible. The Precambrian intrusives consist of a batholith, the Mount Ethel pluton, a smaller Buffalo Pass pluton, and small dikes or lenses of fine-grained porphyry, pegmatites, and ultramafics. The Mount Ethel pluton is an oval shaped body 7 miles wide by about 40 miles long (shown by geophysical data to extend beneath younger sediments in North Park). Outer batholithic contacts are sharp and dip steeply outward at about 85°. Five mappable internal variants consist, in order of decreasing age, of granodiorite, quartz monzonite porphyry of Rocky Peak, quartz monzonite of Roxy Ann Lake, granite and quartz monzonite, and. leucogranite. Internal contacts between these plutonic variants are sharp, and evidence of liquid-solid relationships abounds; despite this, all rocks except the granodiorite contribute to an Rb-Sr whole-rock isochron indicating emplacement about 1.4 b.y. (billion years) ago. The most important variants volumetrically are: the quartz monzonite porphyry of Rocky Peak, which forms an irregular 2-mile-thick carapace or mapped band around the west edge of the pluton and is lithologically similar to nearby Sherman Granite, and the quartz monzonite of Roxy Ann Lake, which forms most of the rest of the pluton and is lithologically similar to Silver Plume Granite. An apparent Sherman -Silver Plume dichotomy with similar rock types and similar relative ages is noted throughout Colorado plutons of that age. The Buffalo Pass pluton consists of the quartz monzonite and gra- nodiorite augen gneiss of Buffalo Mountain and equigranular quartz monzonite gneiss. Internal contacts are not exposed. These rocks contribute to an Rb-Sr whole-rock isochron indicating syntectonic emplacement 1.7-1.8 b.y. ago, essentially the same as the metamorphism of the felsic gneiss wallrocks in the area of this report, and of rocks of Boulder Creek age elsewhere in Colorado. The fine-grained porphyry dikes cut the Buffalo Pass pluton, the ultramafics, and some pegmatites. The dikes are within the age range of the Mount Ethel pluton and are older than the mylonite and shear zones. They occur in both an older northwest-trending and a somewhat younger northeast-trending set but do not appear to change compositionally from one set to the other. Regional considerations indicate that they were emplaced between about 1.1 and 1.5 b.y. ago, a time when intermediate to mafic dikes were commonly emplaced throughout Colorado, Wyoming, and southwestern Montana. The pegmatite and ultramafic bodies are not dated directly, but clustering of many pegmatites outside the contacts of the Mount Ethel pluton may indicate a genetic relation of the pegmatites to the Mount Ethel rocks. Fluorite is a common accessory mineral in the rocks of the Mount Ethel pluton; it has not been observed in this area in the petrographically similar rocks of the Buffalo Pass pluton. Fluorite was precipitated most abundantly from the Precambrian magma that formed the quartz monzonite of Roxy Ann Lake. In 70 percent of these rocks fluorite is observed in amounts as great as 2 percent and is successively less abundant in both older and younger plutonic phases. Textural evidence indicates that, although most fluorite is intergrown with and contemporaneous with other magmatic minerals, some fluorite is associated with alteration minerals in a manner demonstrating its mobility since its initial deposition.

Colorado↗

USGS2010

U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Center-Fiscal Year 2009 Annual Report

The Earth Resources Observation and Science (EROS) Center is a U.S. Geological Survey (USGS) facility focused on providing science and imagery to better understand our Earth. As part of the USGS Geography Discipline, EROS contributes to the Land Remote Sensing (LRS) Program, the Geographic Analysis and Monitoring (GAM) Program, and the National Geospatial Program (NGP), as well as our Federal partners and cooperators. The work of the Center is shaped by the Earth sciences, the missions of our stakeholders, and implemented through strong program and project management and application of state-of-the-art information technologies. Fundamentally, EROS contributes to the understanding of a changing Earth through 'research to operations' activities that include developing, implementing, and operating remote sensing based terrestrial monitoring capabilities needed to address interdisciplinary science and applications objectives at all levels-both nationally and internationally. The Center's programs and projects continually strive to meet and/or exceed the changing needs of the USGS, the Department of the Interior, our Nation, and international constituents. The Center's multidisciplinary staff uses their unique expertise in remote sensing science and technologies to conduct basic and applied research, data acquisition, systems engineering, information access and management, and archive preservation to address the Nation's most critical needs. Of particular note is the role of EROS as the primary provider of Landsat data, the longest comprehensive global land Earth observation record ever collected. This report is intended to provide an overview of the scientific and engineering achievements and illustrate the range and scope of the activities and accomplishments at EROS throughout fiscal year (FY) 2009. Additional information concerning the scientific, engineering, and operational achievements can be obtained from the scientific papers and other documents published by EROS staff. We welcome comments and follow-up questions on any aspect of this Annual Report and invite any of our customers or partners to contact us at their convenience. To communicate with us, or for more information about EROS, contact: Communications and Outreach, USGS EROS Center, 47914 252nd Street, Sioux Falls, South Dakota 57198, jsnelson@usgs.gov, http://eros.usgs.gov/.

Open-File Report↗

USGS2006

Hydrogeologic framework refinement, ground-water flow and storage, water-chemistry analyses, and water-budget components of the Yuma area, southwestern Arizona and southeastern California

The ground-water and surface-water system in the Yuma area in southwestern Arizona and southeastern California is managed intensely to meet water-delivery requirements of customers in the United States, to manage high ground-water levels in the valleys, and to maintain treaty-mandated water-quality and quantity requirements of Mexico. The following components in this report, which were identified to be useful in the development of a ground-water management model, are: (1) refinement of the hydrogeologic framework; (2) updated water-level maps, general ground-water flow patterns, and an estimate of the amount of ground water stored in the mound under Yuma Mesa; (3) review and documentation of the ground-water budget calculated by the Bureau of Reclamation, U.S. Department of the Interior (Reclamation); and (4) water-chemistry characterization to identify the spatial distribution of water quality, information on sources and ages of ground water, and information about the productive-interval depths of the aquifer. A refined three-dimensional digital hydrogeologic framework model includes the following hydrogeologic units from bottom to top: (1) the effective hydrologic basement of the basin aquifer, which includes the Pliocene Bouse Formation, Tertiary volcanic and sedimentary rocks, and pre-Tertiary metamorphic and plutonic rocks; (2) undifferentiated lower units to represent the Pliocene transition zone and wedge zone; (3) coarse-gravel unit; (4) lower, middle, and upper basin fill to represent the upper, fine-grained zone between the top of the coarse-gravel unit and the land surface; and (5) clay A and clay B. Data for the refined model includes digital elevation models, borehole lithology data, geophysical data, and structural data to represent the geometry of the hydrogeologic units. The top surface of the coarse-gravel unit, defined by using borehole and geophysical data, varies similarly to terraces resulting from the down cutting of the Colorado River. Clay A is nearly the same as the previous conceptual hydrogeologic model definition (Olmsted and others, 1973), except for a minor westward extension from the city of Yuma. Clay B is extended to the southerly international boundary and increased in areal extent by about two-thirds of the original extent (Olmsted and others, 1973). The other hydrogeologic units generally are the same as in the previous conceptual hydrogeologic model. Before development, the Colorado and Gila Rivers were the sources of nearly all the ground water in the Yuma area through direct infiltration of water from river channels and annual overbank flooding. After construction of upstream reservoirs and clearing and irrigation of the floodplains, the rivers now act as drains for the ground water. Ground-water levels in most of the Yuma area are higher now than they were in predevelopment time. A general gradient of ground-water flow toward the natural discharge area south of the Yuma area still exists, but many other changes in flow are evident. Ground water in Yuma Valley once flowed away from the Colorado River, but now has a component of flow towards the river and Mexicali Valley. A ground-water mound has formed under Yuma Mesa from long-term surface-water irrigation; about 600,000 to 800,000 acre-ft of water are stored in the mound. Ground-water withdrawals adjacent to the southerly international boundary have resulted in water-level declines in that area. The reviewed and documented water budget includes the following components: (1) recharge in irrigated areas, (2) evapotranspiration by irrigated crops and phreatophytes, (3) ground-water return flow to the Colorado River, and (4) ground-water withdrawals (including those in Mexicali Valley). Recharge components were calculated by subtracting the amount of water used by crops from the amount of water delivered. Evapotranspiration rates were calculated on the basis of established methods, thus were appropriate for input to the ground-water flow model developed by the Bureau of Reclamation (William Greer, hydrologist, Bureau of Reclamation, written commun., 2005). Evapotranspiration by crops and phreatophytes were calculated by using crop coefficient methods and meteorological data. Other methods of calculating evapotranspiration rates by using combinations of satellite imagery and ground-based data could be used for higher spatial and temporal resolution. Ground-water return flow during years of low flow on the Colorado River (1972–82, 1987–92, and 1994–96) averaged 79,000 acre-ft per year. Ground-water withdrawal data for 1970–99 were similar to other estimates made by the U.S. Geological Survey for the Yuma area. New water-chemistry data were collected in 12 wells and 8 canals/drains to characterize spatial patterns in chemical constituents, determine isotopic ages of water, infer possible sources of ground water, and locate the vertical intervals of the aquifer that contribute most water to wells. Depth-dependent samples were collected at one of the wells (YM-10). A large quantity of water-quality data were compiled from Bureau of Reclamation and U.S. Geological Survey records and merged into the U.S. Geological Survey National Water Information System database. New samples were analyzed for major ions, nutrients, stable isotopes of oxygen and hydrogen, tritium ( 3 H), and carbon-14 ( 14 C) (along with C 13 /C 12 ratios). Light values of oxygen-18 ( 18 O) and deuterium ( 2 H, D) in well 242-2 indicate recharge from the Colorado River. Heavy water samples from wells 242-22, CADC, and Mesa del Sol indicate local recharge sources. Tritium data indicate there is young water in wells in the valleys and near the edge of Yuma Mesa, while older water is found far from the Colorado River. 14 C data indicate that water from wells near the southerly international boundary is at least several thousand years old.

Arizona, California↗