Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Ground Water Modeling Investigation Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23Linked to original sources
USGS1988

Geohydrology, water quality, and preliminary simulations of ground-water flow of the alluvial aquifer in the upper Black Squirrel Creek basin, El Paso County, Colorado

The upper Black Squirrel Creek basin in eastern El Paso County, Colorado, is underlain by an alluvial aquifer and four bedrock aquifers. The climate of the area is semiarid, and streamflow is irregular. The alluvial aquifer has supplied water to wells since the late 1800's when ranchers first pumped water from shallow wells to grow grass hay for livestock. Ground-water pumpage from the alluvial aquifer has increased since the mid-1950's, and water-level declines have been substantial; the bedrock aquifers virtually are undeveloped. Ground-water pumpage for domestic, stock, agricultural, and municipal uses has exceeded recharge for the past 25 years. The present extent of the effect of pumpage on the alluvial aquifer was evaluated, and a ground-water flow model was used to simulate the future effect of continued pumpage on the aquifer. Measured water-level declines from 1974 through 1984 were as much as 30 feet in an area north of Ellicott, Colorado. On the basis of the simulations, water-level declines from October 1984 to April 1999 north of Ellicott might be as much as 20 to 30 feet and as much as 1 to 10 feet in most of the aquifer. Flow from the bedrock aquifers to the alluvial aquifer may account for a substantial volume of the recharge to the alluvial aquifer. The ground-water flow models provided a means of evaluating the importance of ground-water evapotranspiration at various stages of aquifer development. Simulated ground-water evapotranspiration decreased from 1949 to 1984; prior to 1950 ground-water evapotranspiration was about 43.5 percent of the total outflow, but in 1984 it was less than 3 percent. Thirty-six ground-water samples were collected during 1984. Chemical analyses indicated that concentrations of dissolved nitrite plus nitrate as nitrogen generally were large. Samples from 5 of the 36 wells had concentrations of dissolved nitrite plus nitrate as nitrogen that exceeded drinking-water standards; these concentrations could pose a health threat toinfants. Water from the alluvial aquifer generally is of suitable quality forother uses.

Colorado↗
USGS2007

Areas Contributing Recharge to Wells in the Tafuna-Leone Plain, Tutuila, American Samoa

To address the concerns about the potential for contamination of drinking-water wells in the Tafuna-Leone Plain, Tutuila, American Samoa, a numerical ground-water flow model was developed and used to delineate areas contributing recharge to the wells (ACRWs). Surveys and analyses were conducted to obtain or compile certain essential hydrogeologic information needed for the model, such as groundwater production statistics, ground-water levels under current production, and an assessment of the distribution of groundwater recharge. The ground-water surveys indicate that total production from all wells in the Tafuna-Leone Plain between 1985 and 2005 averaged 6.1 Mgal/d and showed a gradual increase. A synoptic survey indicates that current water levels in the Tafuna-Leone Plain are highest near its inland boundary, decrease toward the coast, and are slightly depressed in high-production well fields. Ground-water levels showed little effect from the increased production because hydraulic conductivites are high and withdrawal is small relative to recharge. Analysis of ground-water recharge using a soil water-budget analysis indicates that the Tafuna-Leone Plain and adjacent areas receive about 280 Mgal/d of water from rainfall, of which 24 percent runs off to the ocean, 26 percent is removed by evapotranspiration, and 50 percent goes to ground-water recharge. Ground-water recharge per unit area is generally higher at the mountain crests than at the coast, but the highest recharge per unit area is in the mountain-front recharge zone at the juncture between the Tafuna-Leone Plain and the adjacent mountains. Surface water from the mountains also contributes to ground-water recharge in the eastern Tafuna-Leone Plain, in a process analogous to mountain-front recharge described in arid areas. Analysis of stream-gage data indicates that in the mountains of Tutuila, ground water discharges and contributes substantially to the total flow of the streams. In contrast, multiple lines of evidence indicate that in the eastern Tafuna-Leone Plain, surface water recharges the highly permeable underlying aquifer. Steady-state model simulations representing current ground-water production conditions in the Tafuna-Leone Plain indicate that most ACRWs extend less than a mile from the production wells; thus, travel distance between any point within an ACRW and its well is short. A simulation representing a condition in which all wells are operating at maximum capacity resulted in larger ACRWs, which demonstrates that increasing ground-water withdrawal from existing wells, or building and developing new wells, increases the surface area that could potentially contribute contaminants. In some places, such as in Malaeimi Valley, water can travel quickly via surface-water routes to an area where the water can infiltrate within the ACRWs of a well field.

Scientific Investigations Report↗
USGS2000

Probability of detecting atrazine/desethyl-atrazine and elevated concentrations of nitrate plus nitrate as nitrogen in ground water in the Idaho part of the western Snake River Plain

As ground water continues to provide an ever-growing proportion of Idaho?s drinking water, concerns about the quality of that resource are increasing. Pesticides (most commonly, atrazine/desethyl-atrazine, hereafter referred to as atrazine) and nitrite plus nitrate as nitrogen (hereafter referred to as nitrate) have been detected in many aquifers in the State. To provide a sound hydrogeologic basis for atrazine and nitrate management in southern Idaho—the largest region of land and water use in the State—the U.S. Geological Survey produced maps showing the probability of detecting these contaminants in ground water in the upper Snake River Basin (published in a 1998 report) and the western Snake River Plain (published in this report). The atrazine probability map for the western Snake River Plain was constructed by overlaying ground-water quality data with hydrogeologic and anthropogenic data in a geographic information system (GIS). A data set was produced in which each well had corresponding information on land use, geology, precipitation, soil characteristics, regional depth to ground water, well depth, water level, and atrazine use. These data were analyzed by logistic regression using a statistical software package. Several preliminary multivariate models were developed and those that best predicted the detection of atrazine were selected. The multivariate models then were entered into a GIS and the probability maps were produced. Land use, precipitation, soil hydrologic group, and well depth were significantly correlated with atrazine detections in the western Snake River Plain. These variables also were important in the 1998 probability study of the upper Snake River Basin. The effectiveness of the probability models for atrazine might be improved if more detailed data were available for atrazine application. A preliminary atrazine probability map for the entire Snake River Plain in Idaho, based on a data set representing that region, also was produced. In areas where this map overlaps the 1998 map of the upper Snake River Basin, the two maps show broadly similar probabilities of detecting atrazine. Logistic regression also was used to develop a preliminary statistical model that predicts the probability of detecting elevated nitrate in the western Snake River Plain. A nitrate probability map was produced from this model. Results showed that elevated nitrate concentrations were correlated with land use, soil organic content, well depth, and water level. Detailed information on nitrate input, specifically fertilizer application, might have improved the effectiveness of this model.

Idaho↗
USGS1998

Simulation of ground-water flow, Dayton area, southwestern Ohio

A numerical model was used simulate the regional ground-water-flow system in the Dayton area in southwestern Ohio. Ground water is the primary source of drinking water for the Dayton area. The aquifer consists of glacial sands and gravels in a buried bedrock valley. The shale bed rock in the area is poorly permeable, but the glacial deposits can yield up to 2,000 gallons per minute to wells. Interaction with surface water is an important component of the ground-water-flow system. A steady-state, three dimensional, three-layer MODFLOW model of the glacial deposits was constructed to simulate the ground-water-flow system. The modeled area encompasses about 241 mi2 in Montgomery, Greene, and Clark Counties. The model simulated steady-state conditions of September 1993 and included 187 pumped wells. Hydraulic conductivities in the model ranged from less than 1 foot per day to 450 feet per day. Simulated recharge rates ranged from 6 inches per year to 12.2 inches per year. Recharge was used in select areas to simulate inflow from the bed rock-valley walls. Measured water levels from 579 wells and streamflow gain-loss data from six river reaches were used to evaluate the model. Ninety-one percent of simulated heads were within 15 feet of the measured heads. The root-mean-square error and mean absolute difference between measured and simulated heads were 7.3 feet and 4.5 feet respectively for layer 1, 10.1 feet and 6.5 feet for layer 2, and 8.8 feet and 6.8 feet for layer 3. Recharge and river leakage accounts for 81 percent of the water entering the model; pumped wells and river leakage accounts for almost 91 percent of the ground water leaving the model. Interaction of the ground-water system and the major rivers, which include the Great Miami, Mad, Stillwater, and Little Miami Rivers, is known from previous investigations in the area; however, the model simulation indicates that the smaller streams also may have a significant local influence. The vertical hydraulic conductivity of the glacial deposits appears to have more effect on ground-water flow in some areas near the bed rock-valley walls than in the central areas of the valley. At a local scale, simulated heads in the central areas of the valley were generally insensitive to changes in aquifer parameters. The sensitivity of the model to changes in simulated hydraulic properties of the aquifer was assessed by systematically changing model parameters in four subareas of the model. All areas of the model were sensitive to changes in recharge. Changes in other parameters, such as hydraulic conductivity or riverbed conductance, had variable effects. The sensitivity of the model can be used to indicate the types of additional hydrogeologic data that would be most useful to future investigations.

Water-Resources Investigations Report↗
USGS2009

Assessment of Ground-Water Resources in the Seacoast Region of New Hampshire

Numerical ground-water-flow models were developed for a 160-square-mile area of coastal New Hampshire to provide insight into the recharge, discharge, and availability of ground water. Population growth and increasing water use prompted concern for the sustainability of the region's ground-water resources. Previously, the regional hydraulic characteristics of the fractured bedrock aquifer in the Seacoast region of New Hampshire were not well known. In the current study, the ground-water-flow system was assessed by using two different models developed and calibrated under steady-state seasonal low-flow and transient monthly conditions to ground-water heads and base-flow discharges. The models were, (1) a steady-state model representing current (2003-04) seasonal low-flow conditions used to simulate current and future projected water use during low-flow conditions; and (2) a transient model representing current average and estimated future monthly conditions over a 2-year period used to simulate current and future projected climate-change conditions. The analysis by the ground-water-flow models indicates that the Seacoast aquifer system is a transient flow system with seasonal variations in ground-water flow. A pseudosteady- state condition exists in the fall when the steady-state model was calibrated. The average annual recharge during the period analyzed, 2000-04, was approximately 51 percent of the annual precipitation. The average net monthly recharge rate between 2003 and 2004 varied from 5.5 inches per month in March, to zero in July, and to about 0.3 inches per month in August and September. Recharge normally increases to about 2 inches per month in late fall and early winter (November through December) and declines to about 1.5 inches per month in late winter (January and February). About 50 percent of the annual recharge coincides with snowmelt in the spring (March and April), and 20 percent occurs in the late fall and early winter (November through February). Net recharge, calculated as infiltration of precipitation minus evapotranspiration, can be negative during summer months (particularly July). Regional bulk hydraulic conductivities of the bedrock aquifer were estimated to be about 0.1 to 1.0 feet per day. Estimated hydraulic conductivities in model areas representing the Rye Complex and the Kittery Formation were higher (0.5 to 1 foot per day) than in areas representing the Eliot Formation, the Exeter Diorite, and the Newburyport Complex, which have estimated hydraulic conductivities of 0.1 to 0.2 foot per day. A northeast-southwest regional anisotropy of about 5:1 was estimated in some areas of the model; this pattern is parallel to the regional structural trend and predominant fracture orientation. In areas of the model with more observation data, the upper and lower 95-percent confidence intervals for the estimated bedrock hydraulic conductivity were about half an order of magnitude above and below the parameter, respectively, and the estimated confidence intervals for estimated specific storage were within an order of magnitude of the parameter. In areas of the model with few data points, or few stresses, confidence intervals were several orders of magnitude. Estimated model parameters and their confidence intervals are a function of the conceptual model design, observation data, and the weights placed on the data. The amount of recharge that enters the bedrock aquifer at a specific point depends on (1) the location of the point in the flow field; (2) the hydraulic conductivity of the bedrock (or the connectivity of fractures); and (3) the stresses within the bedrock aquifer. In addition, ground water stored in unconsolidated overburden sediments, including till and other fine-grained sediments, may constitute a large percentage of the water available from storage to the bedrock aquifer. Recharge into the bedrock aquifer at a point can range from zero to nearly all the recharge at the surface dependin

Scientific Investigations Report↗
USGS1998

Surface-water/ground-water relations in the Lemhi River Basin, east-central Idaho

This report summarizes work carried out in cooperation with the Bureau of Reclamation to provide hydrologic information to help Federal, State, and local agencies meet the goals of the Lemhi River Model Watershed Project. The primary goal of the project is to maintain, enhance, and restore anadromous and resident fish habitat in the Lemhi River, while maintaining a balance between resource protection and established water uses. The main objectives of the study were to carry out seepage measurements to determine seasonal distributed gains and losses in the Lemhi River and to estimate annual ground-water underflow from the basin to the Salmon River. In 1997, seepage measurements were made during and after the irrigation season along a 60-mile reach of the Lemhi River between Leadore and Salmon. Except for one 4-mile reach that lost 1.3 cubic feet per second per mile, the river gained from ground water in early August when ground-water levels were high. Highest flows in the Lemhi River in early August were about 400 cubic feet per second. In October, when ground-water levels were low, river losses to ground water were about 1 to 16 cubic feet per second per mile. In October, highest flows in the Lemhi River were about 500 cubic feet per second, near the river's mouth. Annual ground-water underflow from the Lemhi River Basin to the Salmon River was estimated by using a simplified water budget and by using Darcy's equation. The water-budget method contained large uncertainties associated with estimating precipitation and evapotranspiration. Results of both methods indicate that the quantity of ground water leaving the basin as underflow is small, probably less than 2 percent of the basin's total annual water yield.

Idaho↗
USGS2009

Estimating Locations of Perennial Streams in Idaho Using a Generalized Least-Squares Regression Model of 7-Day, 2-Year Low Flows

Many State and Federal agencies use information regarding the locations of streams having intermittent or perennial flow when making management and regulatory decisions. For example, the application of some Idaho water quality standards depends on whether streams are intermittent. Idaho Administrative Code defines an intermittent stream as one having a 7-day, 2-year low flow (7Q2) less than 0.1 ft3/s. However, there is a general recognition that the cartographic representation of perennial/intermittent status of streams on U.S. Geological Survey (USGS) topographic maps is not as accurate or consistent as desirable from one map to another, which makes broad management and regulatory assessments difficult and inconsistent. To help resolve this problem, the USGS has developed a methodology for predicting the locations of perennial streams based on regional generalized least-squares (GLS) regression equations for Idaho streams for the 7Q2 low-flow statistic. Using these regression equations, the 7Q2 streamflow may be estimated for naturally flowing streams in most areas in Idaho. The use of these equations in conjunction with a geographic information system (GIS) technique known as weighted flow accumulation allows for an automated and continuous estimation of 7Q2 streamflow at all points along stream reaches. The USGS has developed a GIS-based map of the locations of streams in Idaho with perennial flow based on a 7Q2 of 0.1 ft3/s and a transition zone of plus or minus 1 standard error. Idaho State cooperators plan to use this information to make regulatory and water-quality management decisions. Originally, 7Q2 equations were developed for eight regions of similar hydrologic characteristics in the study area, using long-term data from 234 streamflow-gaging stations. Equations in five of the regions were revised based on spatial patterns observed in the initial perennial streams map and unrealistic behavior of the equations in extrapolation. The standard errors of prediction for the final equations ranged from a minimum of +75.0 to -42.9 percent in the central part of the study area to a maximum of +277 to -73.5 percent in the southern part of the study area. The equations are applicable only to unregulated, naturally-flowing streams and may produce unreliable results outside the range of explanatory variables used for equation development. Extrapolation outside the range of available data was necessary, however, to predict perennial flow initiation points and transition zones along stream reaches. The map of perennial streams was evaluated by comparing predicted stream classifications with four independent datasets, including field observations by other government agencies. Overall, 81 percent of the comparison data points agreed with the USGS perennial streams model. Regions with the highest number of disagreements had a high percentage of mountainous and forested area with potential mountain front recharge zones, and regions with the highest agreements had a high percentage of low gradient, low elevation area. As a whole, the USGS model predicted a higher number of perennial streams than predictions made with the independent datasets. Some disagreements were due to poor site location coordinates, timing of the comparison site visits during unusually wet or dry years, discrepancies in classification criteria, and variable ground water contributions to flow in some areas. The Idaho Department of Environmental Quality Beneficial Use Reconnaissance Program (BURP) dataset is considered the most representative dataset for comparison because it covered a range of climate conditions and the number of sites visited were consistent from year to year during the study period. Eighty-five percent of BURP comparison data points agreed with the USGS perennial streams model. Although site-specific flow data may be needed to correctly classify streams in some areas, this information rarely is available and is not always practical to o

Scientific Investigations Report↗
USGS1994

An updated numerical simulation of the ground-water flow system for the Castle Lake debris dam, Mount St. Helens, Washington, and implications for dam stability against heave

A numerical simulation of the ground-water flow system in the Castle Lake debris dam, calibrated to data from the 1991 and 1992 water years, was used to estimate factors of safety against heave and internal erosion. The Castle Lake debris dam, 5 miles northwest of the summit of Mount St. Helens, impounds 19,000 acre-ft of water that could pose a flood hazard in the event of a lake breakout. A new topographic map of the Castle Lake area prior to the 1980 eruption of Mount St. Helens was prepared and used to calculate the thickness of the debris avalanche deposits that compose the dam. Water levels in 22 piezometers and discharges from seeps on the dam face measured several times per year beginning in 1990 supplemented measurements in 11 piezometers and less frequent seep discharge measurements made since 1983. Observations in one group of piezometers reveal heads above the land surface and head gradients favoring upward flow that correspond to factors of safety only slightly greater than 2. The steady-state ground-water flow system in the debris dam was simulated using a threedimensional finite difference computer program. A uniform, isotropic model having the same shape as the dam and a hydraulic conductivity of 1.55 ft/day simulates the correct water level at half the observation points, but is in error by 10 ft or more at other points. Spatial variations of hydraulic conductivity were required to calibrate the model. The model analysis suggests that ground water flows in both directions between the debris dam and Castle Lake. Factors of safety against heave and internal erosion were calculated where the model simulated upward flow of ground water. A critical gradient analysis yields factors of safety as low as 2 near the piezometers where water level observations indicate low factors of safety. Low safety factors are also computed near Castle Creek where slumping was caused by a storm in January, 1990. If hydraulic property contrasts are present in areas of the debris dam unsampled by piezometers, then low safety factors may exist that are not evident in the numerical model analysis. Numerical model simulations showed that lowering Castle Lake by 40 feet increases many factors of safety by 0.1, but increases greater than 1 are limited to the area of 1990 slumping.

Washington↗
USGS1989

Effect of urban runoff on the quality of lakes in Eagan, Minnesota

Sixteen lakes in the city of Eagan, Minnesota, were sampled during 1982-83 to detect water-quality changes that might have occurred because of urbanization since a previous study conducted during 1972-78. Each of the lakes was sampled five times to determine pH, specific conductance, dissolved oxygen, water temperature, transparency, and concentration of dissolved chloride. Three determinations of chlorophyll were made for each of the lakes near the end of the study, and additional determinations were made for a few lakes of particular interest. Most of the lakes have been incorporated into the city's storm-runoff system for use as retention basins during large storms. The chemistry of the lakes appears to be degraded by urban runoff. Chloride concentrations were significantly higher in six lakes than during the previous study, and remained elevated (about 30 milligrams per liter) in four other lakes. The association between increased chloride and specific conductance with runoff from urban areas suggests that the lakes are subject to contamination by chloride commonly present in urban runoff, and chloride concentrations harmful to aquatic life may have been associated with high specific conductance measured in one of the lakes. Analysis of the data collected for this study indicate that the chemistry of the lakes changes, adjusting to a variety of influences including (1) alternate loading and flushing by runoff, (2) excessive average-annual precipitation, (3) changing ground-water and lake interactions, and (4) changing land use in the lake watersheds. Some lakes affected by urban runoff had reduced concentrations of total phosphorus; however, other lakes unaffected by urban runoff also had significantly lower phosphorus, suggesting that increased precipitation may have diluted the lake water. Ten phosphorus-loading models tested or developed during the previous study generally were found to be inadequate for describing the results of this study. The trophic status of 12 lakes improved but declined in the other 4 lakes, and productivity increased 38 percent in what had been the least-eutrophic lake.

Minnesota↗
USGS1992

Geohydrology of, and simulation of ground-water flow in, the Milford-Souhegan glacial-drift aquifer, Milford, New Hampshire

Hydrogeologic data collected since 1990 were assessed and a ground-water-flow model was refined in this study of the Milford-Souhegan glacial-drift aquifer in Milford, New Hampshire. The hydrogeologic data collected were used to refine estimates of hydraulic conductivity and saturated thickness of the aquifer, which were previously calculated during 1988-90. In October 1990, water levels were measured at 124 wells and piezometers, and at 45 stream-seepage sites on the main stem of the Souhegan River, and on small tributary streams overlying the aquifer to improve an understanding of ground-water-flow patterns and stream-seepage gains and losses. Refinement of the ground-water-flow model included a reduction in the number of active cells in layer 2 in the central part of the aquifer, a revision of simulated hydraulic conductivity in model layers 2 and representing the aquifer, incorporation of a new block-centered finite-difference ground-water-flow model, and incorporation of a new solution algorithm and solver (a preconditioned conjugate-gradient algorithm). Refinements to the model resulted in decreases in the difference between calculated and measured heads at 22 wells. The distribution of gains and losses of stream seepage calculated in simulation with the refined model is similar to that calculated in the previous model simulation. The contributing area to the Savage well, under average pumping conditions, decreased by 0.021 square miles from the area calculated in the previous model simulation. The small difference in the contrib- uting recharge area indicates that the additional data did not enhance model simulation and that the conceptual framework for the previous model is accurate.

Water-Resources Investigations Report↗
USGS1984

Water-table contours, directions of ground-water movement, and measurements of inflow to American Falls Reservoir, southeastern Idaho, April 1984

In 1978 the U.S. Geological Survey began a 5-year study of the High Plains regional aquifer system to provide hydrologic information for evaluating the effects of long-term development of the aquifer and to develop a capability for predicting aquifer response to alternative changes in ground-water management. By use of a digital model, this report presents a quantitative description of the High Plains aquifer in Oklahoma. The High Plains aquifer consists predominantly of the Tertiary Ogallala Formation and overlying Quaternary alluvium and terrace deposits which are hydraulically connected to the High Plains aquifer. Much of the aquifer is underlain by formations of Permian through Cretaceous age, which generally have very small hydraulic conductivities. In some areas parts of underlying Triassic, Jurassic, or Cretaceous rocks are hydraulically connected with the aquifer. The High Plains aquifer is a water-table aquifer in which water moves generally to the east-southeast. Before the beginning of extensive irrigation of the 1960's, the aquifer was essentially in dynamic equilibrium with recharge from precipitation balanced by natural discharge from the aquifer. Ground-water discharge appeared in streams leaving the area or was returned to the atmosphere through evapotranspiration. Accurate records of irrigation pumpage are not available from the High Plains. In order to estimate irrigation pumpage, published records of crop distribution were used and a consumptive use was assigned to each principal irrigated crop. This method gave an estimated irrigation demand. Pumpage was taken as a percentage of the total irrigation demand. Irrigation has decreased ground-water discharge from the High Plains aquifer. Ground-water discharge was estimated as approximately 118 cubic feet per second in 1980. A finite-difference digital model was used to simulate flow in the High Plains aquifer. The recharge was adjusted so that 1980 ground-water discharge was 118 cubic feet per second, the estimated ground-water discharge for 1980. Recharge in the eastern half of the modeled area was 0.45 inch per year; one-half this value was used in the western half of the modeled area. Hydraulic conductivity was divided into three zones: 19.3 feet per day in the eastern zone; 16.2 feet per day in the central zone; and 8.28 feet per day in the western zone. A specific yield of 14.7 percent was used in the model. Using all these parameters, the model was calibrated so that the mean difference between predevelopment modeled and measured head was -0.044 foot. Following the calibration procedure, the model was used to predict the volumes of water in storage and distribution of saturated thickness in 1993 and 2020 using the 1980 pumping rates. The calculated quantity of water in storage in the aquifer in 1941 (predevelopment) was approximately 135.2 million acre-feet; in 1980, approximately 121.9 million acre-feet; in 1993 approximately 112.7 million acre-feet; and in 2020, approximately 96.2 million acre-feet. The High Plains aquifer in Oklahoma will continue to be an important source of water past the year 2000. As withdrawals continue from the aquifer at the present rate, the water table will continue to decline and when the water table drops below the streambed in any part of the area, ground-water discharge to streams will cease in that area. Based on the calculated volumes of water in storage, the volume of water remaining in storage as compared to the predevelopment volume is as follows: 90 percent in 1980, 83 percent in 1993, and 71 percent in 2020.

Idaho↗
USGS1996

Water Budget for the Lahaina District, Island of Maui, Hawaii

Ground-water recharge is estimated as the residual component of a monthly water budget calculated using long-term average rainfall, streamflow, irrigation, pan-evaporation data, and soil characteristics. The water-budget components are defined seasonally, through the use of monthly data, and spatially by topographic and geologic areas, through the use of a geographic information system model. The long-term average ground-water recharge for the Lahaina District was estimated for three scenarios using 1923-78 land-use and irrigation data, 1986-93 land-use and irrigation data, and natural conditions. The average annual ground-water recharge rate for 1923-78 conditions is 190 million gallons per day, which is 45 percent of the sum of rainfall and irrigation. The recharge rate for 1986-93 conditions is 163 million gallons per day, which is 42 percent of rainfall plus irrigation. The recharge rate for natural conditions is 145 million gallons per day, which is 44 percent of rainfall.

Water-Resources Investigations Report↗
USGS1977

Ground water in the Lajas Valley, Puerto Rico

Lajas Valley is plagued with salinity and waterlogging problems of the soils. Use of brackish (500 milligrams per liter) ground water for irrigation compounded the problem until an irrigation-drainage system was constructed in 1955. Lajas Valley is an alluvium-filled trough between volcanic and limestone highlands. The alluvium, mostly clay and as much as 300 feet (90 meters) thick, contains brackish ground water except in the recharge areas located along the foothills. Artesian conditions exist in the eastern part of the valley where upward hydraulic gradients have increased due to the addition of irrigation water in the recharge areas. Wells yield up to 200 gallons per minute (13 liters per second) from alluvial fan deposits in the recharge areas. Wells tapping the buried limestone aquifer in the northwest will yield as much as 2,000 gallons per minute (126 liters per second). Results from a digital models show that a network of discharge wells could alleviate waterlogging of the soils in the artesians

Water-Resources Investigations Report↗
USGS1985

Management of ground water and evolving hydrogeologic studies in New Jersey : a heavily urbanized and industrialized state in the northeastern United States

New Jersey is the most densely populated and one of the most industrialized states in the United States. An abundance of freshwater and proximity to major northeastern metropolitan centers has facilitated this development. Pumpage of freshwater from all aquifers in the State in 1980 was 730 million gallons per day (2.76 million cubic meters per day). Management and efficient development of the ground-water resources of the State are the responsibility of the New Jersey Department of Environmental Protection. Laws have been enacted and updated by the State legislature to manage water allocation and to control the disposal of hazardous wastes. Present resource management is guided by the New Jersey Water-Supply Master Plan of 1981. Funding for management activities is partially derived from the sale of state-approved bonds. Effective planning and regional management require accurate and up-to-date hydrologic information and analyses. The U.S. Geological Survey, in cooperation with the New Jersey Geological Survey, is conducting three intensive ground-water studies involving the collection and interpretation of hydrologic data to meet the urgent water-management needs of New Jersey. These studies are part of a long-term cooperative program and are funded through the Water-Supply Bond Act of 1981. They began in 1983 and are scheduled to be completed in 1988. The project areas are situated in the New Jersey part of the Atlantic Coastal Plain in and near Atlantic City, Camden, and South River. They range in size from 400 to 1,200 mil (1,040 to 3,120 km2). The studies are designed to define the geology, hydrology, and geochemistry of the local ground-water systems. The results of these studies will enable the State to address more effectively major problems in these areas such as declining water levels, overpumping, saltwater intrusion, and ground-water contamination resulting from the improper disposal of hazardous wastes. Specific objectives of these studies by the U.S. Geological Survey are to (1) develop an accurate and up-to-date hydrogeologic data base, (2) design and implement a data-collection program and establish a computerized information management system, (3) refine the conceptualization of the ground-water flow system, and (4) define the geochemistry of the aquifer system by conducting a water-quality appraisal. The objectives are accomplished by standard hydrogeologic methods. Information concerning hydrogeologic framework, ground-water levels, water use, hydraulic characteristics, and water quality in the study areas is compiled from all available sources. Additional data needed are collected through well inventories, surface geophysical surveys, water-quality samplings, water-level measurements, and a well-drilling program. Interpretation of the flow system is based on the use of standard analytical techniques and digital flow modeling. Calibrated flow models will provide ground-water managers with a mechanism to develop and test regional water-supply strategies. Definition of the geochemistry of the aquifer system is accomplished through a variety of methods which depend on the problems and available data in the particular study area. The approach includes statistical analysis of water-quality data, reaction-path modeling, and determination of the movement of chemical constituents using analytical and numerical modeling techniques. A combined staff of 25 to 30 professionals and technicians from the New Jersey District office of the U.S. Geological Survey is committed to the three studies. The staff has specialists in geohydrology, numerical modeling, geochemistry, geophysics, and computer science. The findings of these studies will be published in data reports, interpretive reports, instructional manuals and journal articles.

New Jersey↗
USGS1982

Modifications and corrections to the finite-difference model for simulation of three-dimensional ground-water flow

This report describes modifications incorporated into the finite-difference model for simulation of groundwater flow in three dimensions. These modifications extend the application of this model to simulations involving head-dependent sources and sinks (i.e., rivers, evapotranspiration, and springs or drains). Other modifications are made that enhance the iterative-solution process of the Strongly Implicit Procedure (SIP). An acceleration (or dampening) factor is introduced to the matrix equation that is to be solved, and optional methods of computing iteration parameters are incorporated into the original model. This report also describes corrections to the model that eliminate errors in the equation formulation and in mass-balance computations of certain types of simulations. Additional data-input instructions, definitions of new variables, and a list of program-statement changes are given in an appendix. (USGS)

Water-Resources Investigations Report↗
USGS2005

Water quality and ground-water/surface-water interactions along the John River near Anaktuvuk Pass, Alaska, 2002-2003

The headwaters of the John River are located near the village of Anaktuvuk Pass in the central Brooks Range of interior Alaska . With the recent construction of a water -supply system and a wastewater-treatment plant, most homes in Anaktuvuk Pass now have modern water and wastewater systems. The effluent from the treatment plant discharges into a settling pond near a tributary of the John River . The headwaters of the John River are adjacent to Gates of the Arctic National Park and Preserve, and the John River is a designated Wild River . Due to the concern about possible water - quality effects from the wastewater effluent, the hydrology of the John River near Anaktuvuk Pass was studied from 2002 through 2003 . Three streams form the John River at Anaktuvuk Pass : Contact Creek, Giant Creek, and the John River Tributary. These streams drain areas of 90.3 km (super 2) , 120 km (super 2) , and 4.6 km (super 2) , respectively. Water - quality data collected from these streams from 2002 -03 indicate that the waters are a calcium-bicarbonate type and that Giant Creek adds a sulfate component to the John River. The highest concentrations of bicarbonate, calcium, sodium, sulfate, and nitrate were found at the John River Tributary below the wastewater-treatment lagoon. These concentrations have little effect on the water quality of the John River because the flow of the John River Tributary is only about 2 percent of the John River flow. To better understand the ground-water/surface-water interactions of the upper John River, a numerical groundwater-flow model of the headwater area of the John River was constructed. Processes that occur during spring break-up, such as thawing of the active layer and the frost table and the resulting changes of storage capacity of the aquifer, were difficult to measure and simulate. Application and accuracy of the model is limited by the lack of specific hydrogeologic data both spatially and temporally. However, during the mid-winter and open-water periods, the model provided acceptable results and was coupled with a particle-movement model to simulate the movement and possible extent of conservative particles from the wastewater-treatment-plant lagoon.

Scientific Investigations Report↗
USGS2004

Virus fate and transport during recharge using recycled water at a research field site in the Montebello Forebay, Los Angeles County, California, 1997-2000

Total and fecal coliform bacteria distributions in subsurface water samples collected at a research field site in Los Angeles County were found to increase from nondetectable levels immediately before artificial recharge using tertiary-treated municipal wastewater (recycled water). This rapid increase indicates that bacteria can move through the soil with the percolating recycled water over intervals of a few days and vertical and horizontal distances of about 3 meters. This conclusion formed the basis for three field-scale experiments using bacterial viruses (bacteriophage) MS2 and PRD1 as surrogates for human enteric viruses and bromide as a conservative tracer to determine the fate and transport of viruses in recycled water during subsurface transport under actual recharge conditions. The research field site consists of a test basin constructed adjacent to a large recharge facility (spreading grounds) located in the Montebello Forebay of Los Angeles County, California. The soil beneath the test basin is predominantly medium to coarse, moderately sorted, grayish-brown sand. The three tracer experiments were conducted during August 1997, August-September 1998, and August 2000. For each experiment, prepared solutions of bacteriophage and bromide were sprayed on the surface of the water in the test basin and injected, using peristaltic pumps, directly into the feed pipe delivering the recycled water to the test basin. Extensive data were obtained for water samples collected from the test basin itself and from depths of 0.3, 0.6, 1.0, 1.5, 3.0, and 7.6 meters below the bottom of the test basin. The rate of bacteriophage inactivation in the recycled water, independent of any processes occurring in the subsurface, was determined from measurements on water samples from the test basin. Regression analysis of the ratios of bacteriophage to bromide was used to determine the attenuation rates for MS2 and PRD1, defined as the logarithmic reduction in the ratio during each experiment. Although the inactivation rates increased during the third tracer experiment, they were nearly two orders of magnitude less than the attenuation rates. Therefore, adsorption, not inactivation, is the predominant removal mechanism for viruses during artificial recharge. Using the colloid-filtration model, the collision efficiency was determined for both bacteriophage during the second and third field-scale tracer experiments. The collision efficiency confirms that more favorable attachment conditions existed for PRD1, especially during the third tracer experiment. The different collision efficiencies between the second and third tracer experiments possibly were due to changing hydraulic conditions at the research field site during each experiment. The field data suggest that an optimal management scenario might exist to maximize the amount of recycled water that can be applied to the spreading grounds while still maintaining favorable attachment conditions for virus removal and thereby ensuring protection of the ground-water supply.

Scientific Investigations Report↗
USGS2013

Simulating stream transport of nutrients in the eastern United States, 2002, using a spatially-referenced regression model and 1:100,000-scale hydrography

Existing Spatially Referenced Regression on Watershed attributes (SPARROW) nutrient models for the northeastern and southeastern regions of the United States were recalibrated to achieve a hydrographically consistent model with which to assess nutrient sources and stream transport and investigate specific management questions about the effects of wetlands and atmospheric deposition on nutrient transport. Recalibrated nitrogen models for the northeast and southeast were sufficiently similar to be merged into a single nitrogen model for the eastern United States. The atmospheric deposition source in the nitrogen model has been improved to account for individual components of atmospheric input, derived from emissions from agricultural manure, agricultural livestock, vehicles, power plants, other industry, and background sources. This accounting makes it possible to simulate the effects of altering an individual component of atmospheric deposition, such as nitrate emissions from vehicles or power plants. Regional differences in transport of phosphorus through wetlands and reservoirs were investigated and resulted in two distinct phosphorus models for the northeast and southeast. The recalibrated nitrogen and phosphorus models account explicitly for the influence of wetlands on regional-scale land-phase and aqueous-phase transport of nutrients and therefore allow comparison of the water-quality functions of different wetland systems over large spatial scales. Seven wetland systems were associated with enhanced transport of either nitrogen or phosphorus in streams, probably because of the export of dissolved organic nitrogen and bank erosion. Six wetland systems were associated with mitigating the delivery of either nitrogen or phosphorus to streams, probably because of sedimentation, phosphate sorption, and ground water infiltration.

Scientific Investigations Report↗