Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Geologic report (New Jersey)”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23Linked to original sources
USGS2008

EAARL coastal topography — Sandy Hook 2007

These remotely sensed, geographically referenced elevation measurements of Lidar-derived topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of Gateway National Recreation Area's Sandy Hook Unit in New Jersey, acquired on May 16, 2007. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL) was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

New York↗
USGS2014

EAARL-B coastal topography: eastern New Jersey, Hurricane Sandy, 2012: first surface

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for a portion of the New Jersey coastline beachface, acquired pre-Hurricane Sandy on October 26, and post-Hurricane Sandy on November 1 and November 5, 2012. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar system, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map nearshore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site.

New Jersey↗
USGS2014

EAARL-B submerged topography: Barnegat Bay, New Jersey, pre-Hurricane Sandy, 2012

These remotely sensed, geographically referenced elevation measurements of lidar-derived submerged topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for part of Barnegat Bay, New Jersey, acquired pre-Hurricane Sandy on October 18, 22, 23, and 26, 2012. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed originally in a NASA-USGS collaboration. The exploration and processing of lidar data in an interactive or batch mode is supported using ALPS. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. The Airborne Lidar Processing System (ALPS) is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site.

New Jersey↗
USGS2017

Application of at-site peak-streamflow frequency analyses for very low annual exceedance probabilities

The U.S. Geological Survey (USGS), in cooperation with the U.S. Nuclear Regulatory Commission, has investigated statistical methods for probabilistic flood hazard assessment to provide guidance on very low annual exceedance probability (AEP) estimation of peak-streamflow frequency and the quantification of corresponding uncertainties using streamgage-specific data. The term “very low AEP” implies exceptionally rare events defined as those having AEPs less than about 0.001 (or 1 × 10 –3 in scientific notation or for brevity 10 –3 ). Such low AEPs are of great interest to those involved with peak-streamflow frequency analyses for critical infrastructure, such as nuclear power plants. Flood frequency analyses at streamgages are most commonly based on annual instantaneous peak streamflow data and a probability distribution fit to these data. The fitted distribution provides a means to extrapolate to very low AEPs. Within the United States, the Pearson type III probability distribution, when fit to the base-10 logarithms of streamflow, is widely used, but other distribution choices exist. The USGS-PeakFQ software, implementing the Pearson type III within the Federal agency guidelines of Bulletin 17B (method of moments) and updates to the expected moments algorithm (EMA), was specially adapted for an “Extended Output” user option to provide estimates at selected AEPs from 10 –3 to 10 –6 . Parameter estimation methods, in addition to product moments and EMA, include L-moments, maximum likelihood, and maximum product of spacings (maximum spacing estimation). This study comprehensively investigates multiple distributions and parameter estimation methods for two USGS streamgages (01400500 Raritan River at Manville, New Jersey, and 01638500 Potomac River at Point of Rocks, Maryland). The results of this study specifically involve the four methods for parameter estimation and up to nine probability distributions, including the generalized extreme value, generalized log-normal, generalized Pareto, and Weibull. Uncertainties in streamflow estimates for corresponding AEP are depicted and quantified as two primary forms: quantile (aleatoric [random sampling] uncertainty) and distribution-choice (epistemic [model] uncertainty). Sampling uncertainties of a given distribution are relatively straightforward to compute from analytical or Monte Carlo-based approaches. Distribution-choice uncertainty stems from choices of potentially applicable probability distributions for which divergence among the choices increases as AEP decreases. Conventional goodness-of-fit statistics, such as Cramér-von Mises, and L-moment ratio diagrams are demonstrated in order to hone distribution choice. The results generally show that distribution choice uncertainty is larger than sampling uncertainty for very low AEP values.

Scientific Investigations Report↗
USGS2012

Variations in statewide water quality of New Jersey streams, water years 1998-2009

Statistical analyses were conducted for six water-quality constituents measured at 371 surface-water-quality stations during water years 1998-2009 to determine changes in concentrations over time. This study examined year-round concentrations of total dissolved solids, dissolved nitrite plus nitrate, dissolved phosphorus, total phosphorus, and total nitrogen; concentrations of dissolved chloride were measured only from January to March. All the water-quality data analyzed were collected by the New Jersey Department of Environmental Protection and the U.S. Geological Survey as part of the cooperative Ambient Surface-Water-Quality Monitoring Network. Stations were divided into groups according to the 1-year or 2-year period that the stations were part of the Ambient Surface-Water-Quality Monitoring Network. Data were obtained from the eight groups of Statewide Status stations for water years 1998, 1999, 2000, 2001-02, 2003-04, 2005-06, 2007-08, and 2009. The data from each group were compared to the data from each of the other groups and to baseline data obtained from Background stations unaffected by human activity that were sampled during the same time periods. The Kruskal-Wallis test was used to determine whether median concentrations of a selected water-quality constituent measured in a particular 1-year or 2-year group were different from those measured in other 1-year or 2-year groups. If the median concentrations were found to differ among years or groups of years, then Tukey's multiple comparison test on ranks was used to identify those years with different or equal concentrations of water-quality constituents. A significance level of 0.05 was selected to indicate significant changes in median concentrations of water-quality constituents. More variations in the median concentrations of water-quality constituents were observed at Statewide Status stations (randomly chosen stations scattered throughout the State of New Jersey) than at Background stations (control stations that are located on reaches of streams relatively unaffected by human activity) during water years 1998-2009. Results of tests on concentrations of total dissolved solids, dissolved chloride, dissolved nitrite plus nitrate, total phosphorus, and total nitrogen indicate a significant difference in water quality at Statewide Status stations but not at Background stations during the study period. Excluding water year 2009, all significant changes that were observed in the median concentrations were ultimately increases, except for total phosphorus, which varied significantly but in an inconsistent pattern during water years 1998-2009. Streamflow data aided in the interpretation of the results for this study. Extreme values of water-quality constituents generally followed inverse patterns of streamflow. Low streamflow conditions helped explain elevated concentrations of several constituents during water years 2001-02. During extreme drought conditions in 2002, maximum concentrations occurred for four of the six water-quality constituents examined in this study at Statewide Status stations (maximum concentration of 4,190 milligrams per liter of total dissolved solids) and three of six constituents at Background stations (maximum concentration of 179 milligrams per liter of total dissolved solids). The changes in water quality observed in this study parallel many of the findings from previous studies of trends in New Jersey.

New Jersey↗
USGS2014

EAARL-B submerged topography: Barnegat Bay, New Jersey, post-Hurricane Sandy, 2012-2013

These remotely sensed, geographically referenced elevation measurements of lidar-derived submerged topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for part of Barnegat Bay, New Jersey, acquired post-Hurricane Sandy on November 1, 5, 16, 20, and 30, 2012; December 5, 6, and 21, 2012; and January 10, 2013. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar system, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map nearshore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed originally in a NASA-USGS collaboration. The exploration and processing of lidar data in an interactive or batch mode is supported using ALPS. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. The Airborne Lidar Processing System (ALPS) is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site .

New Jersey↗
USGS1971

Geology of the Stroudsburg quadrangle and Adjacent areas, Pennsylvania--New Jersey

The Stroudsburg area is within the Valley and Ridge and Great Valley physiographic provinces, Northampton and Monroe Counties, Pennsylvania, and Warren County, New Jersey. The northeast-trending subparallel valleys and ridges resulted from erosion of folded heterogeneous sedimentary rocks. These are Middle Ordovician to Middle Devonian in age and are more than 17,000 feet thick. Deposition of a thick flysch sequence (Martinsburg Formation of Ordovician age) accompanied onset of Taconic orogenesis. It was followed by deposition of a thick molasse sequence of Silurian and Early Devonian age (continental and marginal-marine clastics--Shawangunk Formation and Bloomsburg Red Beds--overlain by predominantly marginal-marine and subtidal limestone, dolomite, shale, and sandstone--Poxono Island Formation through Oriskany Group). Basin deepening and gradual shallowing occurred during Esopus through Mahantango deposition, heralding the Acadian clastic wedge exposed north of the Stroudsburg area. Interpretation of sedimentary structures and regional stratigraphic relations suggest that the Silurian and Devonian rocks were deposited in the following environments: A1luviated coastal plain (meandering and braided streams), tidal flats (supratidal and intertidal), barrier zone, and neritic zone (upper and lower). The rock stratigraphic units have been grouped into four lithotectonic units, each having a different style of deformation. Folds produced in these rocks are disharmonic, and it is believed that each rock sequence is set off from units above and below by decollements, or zones of detachment. Movement was northwest into the Appalachian basin, primarily by gravitational sliding. The contact between the Shawangunk Formation of Silurian age and Martinsburg Formation of Ordovician age, is one zone of detachment as well as an angular unconformity. Deformational effects of the Middle to Late Ordovician Taconic orogeny are elusive, but it appears that the folds and most minor structures, including the prominent regional cleavage, were produced during the late Paleozoic Appalachian orogeny and are superimposed upon larger Taconic folds and faults. Field relations and microscopic study suggest that the regional cleavage in the Stroudsburg area is due to laminar flow of pelitic material along cleavage folia accompanied by mechanical reorientation of platy and elongate minerals and neocrystallization of mica, quartz, chlorite, and probably albite. Numerous lines of evidence point to the conclusion that cleavage developed after the rock was indurated and formed at, and Just below, conditions of low-grade metamorphism. Intensity of cleavage development increases to the southeast across the area. Second-generation slip cleavage, also believed to be Appalachian in age, formed by mechanical reorientation of minerals as well as by limited new mineral growth. The topography had a profound effect on the direction of movement of the Wisconsin glacier, as well as the manner of its retreat and the deposits that were formed. Till and stratified drift of Wisconsin age and till of Illinoian(?) age are common in the area. Wisconsin deglaciation occurred by northeastward retreat and by stagnation. A conspicuous terminal moraine marks the limit of Wisconsin ice movement. Lake Sciota was dammed between the retreating ice, the moraine, and the surrounding ridges north of Godfrey Ridge. Several deltas mark ice stand positions during the retreat of the ice. Lake-bottom and kame deposits are locally common in Cherry Valley. South of Kittatinny Mountain, on the other hand, melt water was freely discharged to the south. The wind and water gaps in the Stroudsburg area (including Delaware Water Gap and Wind Gap) are structurally controlled; specifically they are located where folds die out in short distances, where folding is locally more intense, or where resistant rocks dip steeply and have a narrow width of outcrop. This conclusion is contrary to

Open-File Report↗
USGS2010

EAARL Coastal Topography-Sandy Hook Unit, Gateway National Recreation Area, New Jersey, Post-Nor'Ida, 2009

These remotely sensed, geographically referenced elevation measurements of lidar-derived bare-earth (BE) and first-surface (FS) topography datasets were produced collaboratively by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, FL, and the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI. This project provides highly detailed and accurate datasets of a portion of the Sandy Hook Unit of Gateway National Recreation Area in New Jersey, acquired post-Nor'Ida (November 2009 nor'easter) on December 4, 2009. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multispectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine aircraft, but the instrument was deployed on a Pilatus PC-6. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Decision Support for Coastal Science and Management website.

Data Series↗
USGS1978

Ore deposits of the Gilman District, Eagle County, Colorado

The Gilman mining district, known also in the past as the Red Cliff district, is in the mountains of southeastern Eagle County, west-central Colorado. The district is the leading source of zinc in Colorado and one of the major base-metal mining districts in the State. As valued at the time of production, total output of zinc, silver, copper, lead, and gold through 1972 was about $328 million. About 90 percent of this total was produced after 1930. The productive part of the district is an area of about 3 square miles (7.8 square kilometers) on the northeast side of the deep canyon of the Eagle River between the small towns of Gilman and Red Cliff. The ore deposits are principally replacement deposits in dolomites of Mississippian and Devonian age and in quartzite of Cambrian age. A few productive veins occur in Precambrian rocks. The replacement deposits crop out in the cliffs of the canyon wall and extend northeastward downdip beneath Battle Mountain, which is composed of a thick sequence of Pennsylvanian clastic rocks. The deposits were originally worked through several separate mines along the canyon wall, but since 1918, all deposits in dolomite rocks, except some small ones near Red Cliff, have been worked through the Eagle mine of the New Jersey Zinc Company at Gilman. The Gilman district lies on the eastern flank of the huge anticline of the Sawatch Range, near the steeply plunging north end of the anticline. Sedimentary rocks on the flank of this part of the anticline dip homoclinally northeastward to a synclinal axis about 8 mi (miles) (13 km (kilometers> northeast of Gilman and then rise more steeply to the Gore fault at the edge of the Gore Range. The homocline is broken by only a few faults most of which have displacements of less than 100 ft (feet) (30 m (meters>. In contrast, the underlying Precambrian rocks are broken by numerous faults and shear zones related to the Homestake shear zone, a northeast-trending master shear zone several miles wide. Fractures and shear zones along the northwest side of the master zone extend beneath the Gilman district. The Gilman district is at the northwestern edge of the northeast-trending Colorado mineral belt as defined by mineralized areas and bodies of intrusive porphyries. Neighboring mining districts in the mineral belt to the southeast of Gilman are the Kokomo lead-zinc district, 13 mi (21 km) distant; the Climax molybdenum district, 16 mi (26 km) distant; and the Leadville district, 20 mi (32 km) distant. These districts, as well as others farther away, are characterized by abundant intrusive rocks of Laramide and middle Tertiary ages and by complex faults systems. The Gilman district, in contrast, contains only a single sill of porphyry and has very simple geologic structure. This probably reflects a position either at the side of or high above a batholith that is inferred from geologic and geophysical data to underlie the mineral belt at shallow depth. The rock column preserved in the district consists, in succession downward, of (1) grit, conglomerate, sandstone, and shale of the Pennsylvanian Minturn Formation, as much as 6,300 ft (1,920 m) thick; (2) shale, limestone, and. sandstone of the Pennsylvanian Belden Formation, 200 ft (61 m) thick; (3) a sill of quartz latite porphyry of the Cretaceous Pando Porphyry about 80 ft (24 m) thick intruded in the basal shale of the Belden Formation; (4) dolomitized limestone of the Mississippian Leadville Dolomite, 110-140 ft (34-43 m) thick; (5) sandstone and sandy and cherty dolomite of the Mississippian or Devonian Gilman Sandstone, 15-50 ft (4.5-15 m) thick; (6) thin-bedded primary or diagenetic dolomite of the Mississippian(?) and Devonian Dyer Dolomite, 50-80 ft (15-24 m) thick; (7) quartzite, conglomerate, and green shale of the Devonian Parting Formation, 35-50 ft (11-15 m) thick; (8) sandstone and shale of the Ordovician Harding Sandstone, 14-80 ft (4.2-24 m) thick; (9) shaly and sandy dolomite and dolom

Professional Paper↗
USGS2023

Simulation of flow and eutrophication in the central Salem River, New Jersey

The central Salem River in New Jersey is subject to periods of water-quality impairment, marked by elevated concentrations of phosphorus and chlorophyll- a , and low concentrations of and large diurnal swings in concentrations of dissolved oxygen. These seasonal eutrophic conditions are controlling factors for water quality in lower reaches, where the river is more lacustrine than in upper reaches, as a result of downstream damming. This biological productivity is supported by nutrient wash-off from agricultural areas in the surrounding watershed. To investigate this impairment, flow measurement and water-quality sampling were conducted during 2007–08 in support of development of a one-dimensional surface-water-quality model that simulates nutrient cycling and transformation processes. The U.S. Geological Survey, in cooperation with the New Jersey Department of Environmental Protection, used the U.S. Environmental Protection Agency Water Quality Analysis Simulation Program (WASP) to develop a receiving-water-quality model of the central Salem River between Woodstown and Deepwater, New Jersey, from April 2007 to October 2008. The main-stem river and largest tributary were simulated. In the flow model, kinematic wave flow is used to simulate flow in upper reaches and ponded weir flow is used to simulate flow in lower reaches. The water-quality model makes use of a mass-balance equation to simulate the fate and transport of nutrients, phytoplankton chlorophyll- a , dissolved oxygen, and oxygen demands (an indicator rather than a substance) in the river. Model input included channel characteristics, boundary conditions for flow and water quality, environmental parameters, vertical dispersion coefficients, settling rates, and kinetic constants. Inputs were estimated where field data were lacking, notably for tributary flows and nutrient loads. The model was calibrated to observed flow variables and concentrations of dissolved oxygen, chlorophyll- a , and nutrients at sampling locations, with emphasis on growing-season conditions. Calibration was achieved through graphical and statistical comparison of simulated results to observed data. Sensitivity analyses were performed, and model limitations and applicability were evaluated. Simulated results closely matched observed data in most cases, although some were overpredicted slightly. The most important causes of overprediction were estimated tributary flows for the flow model and estimated tributary watershed loads for the water-quality model. Calibration of dissolved-oxygen concentrations was closer, and predicted diurnal variations were consistent with high algal photosynthesis/respiration, although lack of continuous dissolved-oxygen data precluded verifying these predictions. A similar caveat applies to predicted diurnal variations in chlorophyll- a . Simulated limitations on algal growth were consistent with those based on observed data and indicated phosphorus was the main limiting nutrient, except during certain periods when nitrogen was limiting. Two water-quality management scenarios were simulated with the model to assess the effect of point- and nonpoint-source nutrient reductions on water-quality conditions in the river. Scenarios involved (1) a return of watershed land use to predevelopment natural conditions and (2) an extreme reduction in nutrient input. Although the extreme-nutrient-reduction scenario yielded improvements in water quality, the natural-conditions scenario yielded the largest improvements as indicated by minimal violations of surface-water-quality standards or thresholds. However, years may be needed to attain the full benefit of these management scenarios as a result of accumulation of phosphorus and organic carbon in riverbed sediments in lacustrine reaches. The results of this study indicate that the quality of water in the central Salem River will improve if management policies that mitigate the effects of nutrient-loading practices in the watershed, particularly those related to agriculture, are implemented.

New Jersey↗
USGS2008

Recovery of Ground-Water Levels From 1988 to 2003 and Analysis of Potential Water-Supply Management Options in Critical Area 1, East-Central New Jersey

Water levels in four confined aquifers in the New Jersey Coastal Plain within Water Supply Critical Area 1 have recovered as a result of reductions in ground-water withdrawals initiated by the State in the late 1980s. The aquifers are the Wenonah-Mount Laurel, the Upper and Middle Potomac-Raritan-Magothy, and Englishtown aquifer system. Because of increased water demand due to increased development in Monmouth, Ocean, and Middlesex Counties, five base and nine alternate management models were designed for the four aquifers to evaluate the effects resulting from potential reallocation of part of the Critical Area 1 reductions in withdrawals. The change in withdrawals and associated water-level changes in the aquifers for 1988-2003 are discussed. Generally, withdrawals decreased 25 to 30 Mgal/d (million gallons per day), and water levels increased 0 to 80 ft (feet). The Regional Aquifer-System Analysis (RASA) ground-water-flow model of the New Jersey Coastal Plain developed by the U.S. Geological Survey was used to simulate ground-water flow and optimize withdrawals using the Ground-Water Management Process (GWM) for MODFLOW. Results of the model were used to evaluate the effects of several possible water-supply management options in order to provide the information to water managers. The optimization method, which provides a means to set constraints that support mandated hydrologic conditions, then determine the maximum withdrawals that meet the constraints, is a more cost-effective approach than simulating a range of withdrawals to determine the effects on the aquifer system. The optimization method is particularly beneficial for a regional-scale study of this kind because of the large number of wells to be evaluated. Before the model was run, a buffer analysis was done to define an area with no additional withdrawals that minimizes changes in simulated streamflow in aquifer outcrop areas and simulated movement of ground water toward the wells from areas of possible high chloride concentrations in the northern and southern parts of the Critical Area. Five base water-supply management models were developed. Each management model has an objective function, decision variables, and constraints. Two of the five management models were test cases: clean slate option and reallocation from the Wenonah-Mount Laurel aquifer and Englishtown aquifer system to small volume wells for potable water use. Nine other models also were developed as part of a trade-off analysis between withdrawal amounts and constraint values. The 14 management models included current (2003) or regularly spaced well locations with variations on the constraints of ground-water head, drawdown, velocity at the 250-mg/L (milligram per liter) isochlor, and withdrawal rate. Results of each management model were evaluated in terms of withdrawals, heads, saltwater intrusion, and source of water by aquifer. Each trade-off curve was defined by using six to nine separate management model runs. Results of the management models designed in this study indicate that a withdrawal reallocation of 5 to 20 Mgal/d within Critical Area 1 would increase the area of heads below -30 ft and the velocity at the 250-mg/L isochlor by up to 4 times that of the simulated 2003 results; the range of values are 0 to 521 square miles and 1 to 20 feet per year, respectively. The increase in area of heads below -30 ft was larger in the Middle Potomac-Raritan-Magothy aquifer than in other aquifers because that area was negligible in 2003. The range of modeled withdrawals is closely tied to management-model design. Interpretation of management model results is provided as well as a discussion of limitations.

Scientific Investigations Report↗
USGS2011

Arsenic, metals, and nutrients in runoff from two detention basins to Raccoon Creek, New Jersey Coastal Plain, 2008

Arsenic (As) concentrations in the waters of Raccoon Creek in southern New Jersey commonly exceed the State\'s Surface Water Quality Standard (SWQS) for freshwater of 0.017 microgram per liter (mu or ug/L). In order to assess contributions of As from residential runoff to the creek, samples of runoff water were collected from a detention basin in each of two residential developments underlain by different geologic formations and at the outlets of those basins. Samples of streamwater also were collected from Raccoon Creek adjacent to the developments. The samples were analyzed to determine concentrations of As, selected metals, organic carbon, and nutrients. Soil samples in and downgradient from the basins also were collected and analyzed. Concentrations of As in unfiltered water samples of runoff from the basin underlain by glauconitic clays generally were higher (up to 4.35 mu or ug/L) than in runoff from the basin underlain by predominantly quartz sands and silts (up to 2.68 mu or ug/L). Chromium (Cr) concentrations also were higher in runoff from the basin underlain by glauconitic clays than in runoff from the basin underlain by quartz sand and silt. In addition, Cr concentrations were higher in the glauconitic soils than in the quartz-rich soils. Metals such as aluminum (Al), iron (Fe), lead (Pb), and manganese (Mn) in the runoff and in the streamwater were mostly in particulate form. Arsenic, most metals, and phosphorus (P) however, were mostly in dissolved form in runoff but in particulate form in the streamwater. Total organic carbon concentrations in the runoff ranged from about 10 to nearly 16 milligrams per liter (mg/L). Given such levels of organic carbon and strong correlations between concentrations of some metals and organic carbon, it may be that many of the metals were complexed with dissolved organic carbon and transported in that form in the runoff. Although underlying geologic materials and soils appear to be major contributors of As to the streamwater, As also could have been contributed from lead arsenate pesticide residues. The residential development underlain by quartz-rich sediments formerly had been an orchard where such pesticides may have been used. The substantial inputs of As to runoff at this site may be attributable to this former land use, although Pb concentrations were about the same in runoff from both sites. The streamwater at both sites, however, contained Pb concentrations well above those in runoff, indicating that there are additional inputs of Pb, perhaps from roadside soils, upstream from the two sampling sites in this study. Positive relations between concentrations of As and some metals with dissolved organic carbon in runoff and streamwater indicate that complexation with organic carbon may provide a mechanism by which these constituents can be transported. Sorption of As, Pb, and P to Fe hydroxides may be indicated by the observed positive relation of particulate As, Pb, and P to particulate Fe, however, representing an additional mechanism for transport of these constituents.

New Jersey↗
USGS2010

Simulation of Runoff and Reservoir Inflow for Use in a Flood-Analysis Model for the Delaware River, Pennsylvania, New Jersey, and New York, 2004-2006

A model was developed to simulate inflow to reservoirs and watershed runoff to streams during three high-flow events between September 2004 and June 2006 for the main-stem subbasin of the Delaware River draining to Trenton, N.J. The model software is a modified version of the U.S. Geological Survey (USGS) Precipitation-Runoff Modeling System (PRMS), a modular, physically based, distributed-parameter modeling system developed to evaluate the impacts of various combinations of precipitation, climate, and land use on surface-water runoff and general basin hydrology. The PRMS model simulates time periods associated with main-stem flooding that occurred in September 2004, April 2005, and June 2006 and uses both daily and hourly time steps. Output from the PRMS model was formatted for use as inflows to a separately documented reservoir and riverrouting model, the HEC-ResSim model, developed by the U.S. Army Corps of Engineers Hydrologic Engineering Center to evaluate flooding. The models were integrated through a graphical user interface. The study area is the 6,780 square-mile watershed of the Delaware River in the states of Pennsylvania, New Jersey, and New York that drains to Trenton, N.J. A geospatial database was created for use with a geographic information system to assist model discretization, determine land-surface characterization, and estimate model parameters. The USGS National Elevation Dataset at 100-meter resolution, a Digital Elevation Model (DEM), was used for model discretization into streams and hydrologic response units. In addition, geospatial processing was used to estimate initial model parameters from the DEM and other data layers, including land use. The model discretization represents the study area using 869 hydrologic response units and 452 stream segments. The model climate data for point stations were obtained from multiple sources. These sources included daily data for 22 National Weather Service (NWS) Cooperative Climate Station network stations, hourly data for 15 stations from the National Climatic Data Center, hourly data for 1 station from the NWS Middle Atlantic River Forecast Center records, and daily and hourly data for 7 stations operated by the New York City Department of Environmental Protection. The NWS Multisensor Precipitation Estimate data set for 2001-2007 was used for computing daily precipitation for the model and for computing hourly precipitation for storm simulation periods. Calibration of the PRMS model included regression and optimization algorithms, as well as manual adjustments of model parameters. The general goal of the calibration procedure was to minimize the difference between discharge measured at USGS streamgages and the corresponding discharge simulated by the model. Daily streamflow data from 35 USGS streamgages were used in model calibration. The streamflow data represent areas draining from 20.2 to 6,780 square miles. The PRMS model simulates reservoir inflow and watershed runoff for use as input into HECResSim for the purpose of evaluating and comparing the effects of different watershed conditions on main-stem flooding in the Delaware River watershed draining to Trenton, N.J. The PRMS model is useful as a planning tool to simulate the effects of land-use changes and different antecedent conditions on local runoff and reservoir inflow and, as input to the HEC-ResSim model, on flood flows in the main stem of the Delaware River.

Open-File Report↗
USGS2026

Analysis of alternative weir designs for improved passage of select fish at the U.S. Geological Survey streamgaging weir at Blackwells Mills, New Jersey

As the population of New Jersey continues to remain dense, the need for water supply will likely continue to be high, which can lead to water managers needing to make difficult decisions about managing drinking-water supply. Streamgaging weirs like the ones used by the U.S. Geological Survey (USGS) play a critical role in providing accurate and stable streamflow data, but their presence can affect the passage of diadromous fish species such as river herring ( Alosa pseudoharengus [alewife], Alosa aestivalis [blueback herring], and Alosa sapidissima [American shad]). In some situations, weirs existing in rivers and streams are no longer used because they were part of a farm irrigation system or some type of industrial operation. The weir at the USGS streamgage 01402000 Millstone River at Blackwells Mills, New Jersey, was purposefully built as a hydraulic-control structure that provides a precise and stable control for the measurement of stage and computation of continuous streamflow. To satisfy the dual need of maintaining accurate streamflow data and providing improved fish passage for select species of fish during migration season, the USGS proposed the development and evaluation of two alternative weir designs that would meet the criteria established for successful passage of American shad, alewife, and blueback herring during their yearly migration. The designs were also required to maintain adequate control of the upstream pool elevation necessary for the precise computation of streamflow used by State agencies for municipal water-supply purposes for surrounding communities. Two alternative weir design modifications were incorporated at the center of the Blackwells Mills weir and modeled using two-dimensional hydraulic modeling software and three-dimensional computational fluid-dynamics software to simultaneously evaluate conditions for passage of the target fish species and effects to streamflow computations at the streamgage. The models were calibrated to existing conditions around the weir location using surveyed-elevation data and recorded stage, streamflow, and velocity in the Millstone River. The alternative weir designs lowered the weir crest by 1.02 feet (ft) and the resulting simulations showed an effective increase in depth of 0.98 ft at the median streamflow of 251 cubic feet per second (ft 3 /s) and 0.96 ft at the 95-percent exceedance streamflow of 98 ft 3 /s. The alternative weir designs were also found to increase streamflow depth across the shallowest portions of the weir structure at the downstream anti-scour skirt by lowering the skirt about 4 inches, allowing for two or more body depths of water for American shad, alewife, and blueback herring at the median migration streamflow of 251 ft 3 /s. The alternative weir designs also reduced the highest stream velocities across the downstream weir sill and anti-scour skirt from about 9 to 10 feet per second, and the depth-averaged velocity to about 7 to 8 feet per second. The sensitivity of the weir with respect to the computation of streamflow was increased from about 1.8 cubic feet per second per hundredth foot to 1.6 cubic feet per second per hundredth foot for streamflows of about 10–100 cubic feet per second.

New Jersey↗
USGS2006

Estimated ground-water availability in the Delaware River basin, 1997-2000

Ground-water availability using a watershed-based approach was estimated for the 147 watersheds that make up the Delaware River Basin. This study, conducted by the U.S. Geological Survey in cooperation with the Delaware River Basin Commission (DRBC), supports the DRBC's Water Resources Plan for the Delaware River Basin. Different procedures were used to estimate ground-water availability for the region underlain by fractured rocks in the upper part of the basin and for surficial aquifers in the region underlain by unconsolidated sediments in the lower part of the basin. The methodology is similar to that used for the Delaware River Basin Commission's Ground-Water Protected Area in Pennsylvania. For all watersheds, ground-water availability was equated to average annual base flow. Ground-water availability for the 109 watersheds underlain by fractured rocks in Delaware, New Jersey, New York, and Pennsylvania was based on lithology and physiographic province. Lithology was generalized by grouping 183 geologic units into 14 categories on the basis of rock type and physiographic province. Twenty-three index streamflow-gaging stations were selected to represent the 14 categories. A base-flow-recurrence analysis was used to determine the average annual 2-, 5-, 10-, 25-, and 50-year-recurrence intervals for each index station. A GIS analysis used lithology and base flow at the index stations to determine the average annual base flow for the 109 watersheds. Average annual base flow for these watersheds ranged from 0.313 to 0.915 million gallons per day per square mile for the 2-year-recurrence interval to 0.150 to 0.505 million gallons per day per square mile for the 50-year-recurrence interval. Ground-water availability for watersheds underlain by unconsolidated surficial aquifers was based on predominant surficial geology and land use, which were determined from statistical tests to be the most significant controlling factors of base flow. Twenty-one index streamflow-gaging stations were selected to represent the 13 categories of predominant surficial geology and land use for the 38 Coastal Plain watersheds. A base-flow-recurrence analysis was used to determine the average annual 2-, 5-, 10-, 25-, and 50-year-recurrence intervals for each group of predominant surficial geology and land use. Average annual base flow for these watersheds ranged from 0.465 to 1.169 million gallons per day per square mile for the 2-year-recurrence interval to 0.178 to 0.670 million gallons per day per square mile for the 50-year-recurrence interval. Estimated 2-, 5-, 10-, 25-, and 50-year annual base-flow-recurrence interval values for each watershed in the Delaware River Basin are considered to be the quantity of ground water available for each watershed over a range of climatic conditions. The recurrence intervals are considered to be relative indicators of climatic difference; the 2-year-recurrence value represents wetter years, and the 50-year-recurrence value represents drier years. The remaining available ground water in each watershed was determined by subtracting current (1997-2000) ground-water withdrawals and consumptive domestic use and adding water recharged by agricultural irrigation and land application of treated-sewage effluent. Ground-water use ranged from 0 to 60.8 percent of available ground water for the 2-year-recurrence interval; it exceeded 25 percent in four watersheds and 50 percent in two watersheds. Ground-water use ranged from 0 to 75.9 percent of available ground water for the 5-year-recurrence interval; it exceeded 25 percent in five watersheds and 50 percent in three watersheds. Ground-water use ranged from 0 to 84.5 percent of available ground water for the 10-year-recurrence interval; it exceeded 25 percent in seven watersheds and 50 percent in four watersheds. Ground-water use ranged from 0 to 103 percent of available ground water for the 25-year-recurrence interval; it exceeded 25 percent in nine watersheds, 5

Delaware, New Jersey, New York, Pennsylvania↗
USGS2007

Summary of selected U.S. Geological survey data on domestic well water quality for the Centers for Disease Control's National Environmental Public Health Tracking Program

About 10 to 30 percent of the population in most States uses domestic (private) water supply. In many States, the total number of people served by domestic supplies can be in the millions. The water quality of domestic supplies is inconsistently regulated and generally not well characterized. The U.S. Geological Survey (USGS) has two water-quality data sets in the National Water Information System (NWIS) database that can be used to help define the water quality of domestic-water supplies: (1) data from the National Water-Quality Assessment (NAWQA) Program, and (2) USGS State data. Data from domestic wells from the NAWQA Program were collected to meet one of the Program's objectives, which was to define the water quality of major aquifers in the United States. These domestic wells were located primarily in rural areas. Water-quality conditions in these major aquifers as defined by the NAWQA data can be compared because of the consistency of the NAWQA sampling design, sampling protocols, and water-quality analyses. The NWIS database is a repository of USGS water data collected for a variety of projects; consequently, project objectives and analytical methods vary. This variability can bias statistical summaries of contaminant occurrence and concentrations; nevertheless, these data can be used to define the geographic distribution of contaminants. Maps created using NAWQA and USGS State data in NWIS can show geographic areas where contaminant concentrations may be of potential human-health concern by showing concentrations relative to human-health water-quality benchmarks. On the basis of national summaries of detection frequencies and concentrations relative to U.S. Environmental Protection Agency (USEPA) human-health benchmarks for trace elements, pesticides, and volatile organic compounds, 28 water-quality constituents were identified as contaminants of potential human-health concern. From this list, 11 contaminants were selected for summarization of water-quality data in 16 States (grantee States) that were funded by the Environmental Public Health Tracking (EPHT) Program of the Centers for Disease Control and Prevention (CDC). Only data from domestic-water supplies were used in this summary because samples from these wells are most relevant to human exposure for the targeted population. Using NAWQA data, the concentrations of the 11 contaminants were compared to USEPA human-health benchmarks. Using NAWQA and USGS State data in NWIS, the geographic distribution of the contaminants were mapped for the 16 grantee States. Radon, arsenic, manganese, nitrate, strontium, and uranium had the largest percentages of samples with concentrations greater than their human-health benchmarks. In contrast, organic compounds (pesticides and volatile organic compounds) had the lowest percentages of samples with concentrations greater than human-health benchmarks. Results of data retrievals and spatial analysis were compiled for each of the 16 States and are presented in State summaries for each State. Example summary tables, graphs, and maps based on USGS data for New Jersey are presented to illustrate how USGS water-quality and associated ancillary geospatial data can be used by the CDC to address goals and objectives of the EPHT Program.

Scientific Investigations Report↗
USGS2021

Simulated effects of sea-level rise on the shallow, fresh groundwater system of Assateague Island, Maryland and Virginia

The U.S. Geological Survey, in cooperation with the National Park Service, developed a three-dimensional groundwater-flow model for Assateague Island in eastern Maryland and Virginia to assess the effects of sea-level rise on the groundwater system. Sea-level rise is expected to increase the altitude of the water table in barrier island aquifer systems, possibly leading to adverse effects to ecosystems on the barrier islands. The potential effects of sea-level rise were evaluated by simulating groundwater conditions under sea-level-rise scenarios of 20 centimeters (cm), 40 cm, and 60 cm. Results show that as sea level rises, low-lying areas of the island originally represented as receiving freshwater recharge in the baseline scenario are inundated by saltwater. This change from freshwater recharge to saltwater decreases the overall amount of freshwater recharging the system. As the water table rises in response to the higher sea levels, freshwater flow out of the system changes, with more freshwater leaving as submarine groundwater discharge and less freshwater leaving as seeps and evapotranspiration. At the current land-surface altitude, as much as 50 percent of the island may be inundated with a 60-cm rise in sea level, and the low-lying marshes may change from freshwater to saltwater. Groundwater levels at 32 wells were monitored for as long as 12 months between October 2014 and September 2015 on Assateague Island. Results from objective classification analysis of 14 shallow monitoring wells show two dominant processes affecting groundwater levels in two different settings on the island. On the western side of the island, between the primary dune and the inland bays, water levels clearly respond to precipitation events. This side of the island is more protected from ocean tides and typically is more vegetated than the eastern side. On the eastern side of the island, between the Atlantic Ocean and the primary dune, water levels clearly respond to tidal events. Specific conductance was measured at four wells, two on the western part of the island and two on the eastern part of the island. Specific conductance values in the two wells west of the primary dune show episodic decreases, coinciding with precipitation events. Specific conductance values in the two wells on the eastern side of the primary dune show episodic increases, coinciding with high-tide events. These high frequency monitoring data are intended to aid in designing a monitoring network that can document both short-term and long-term hydrologic processes on Assateague Island National Seashore. This study uses a modeling approach consistent with models developed for Gateway National Recreation Area, Sandy Hook Unit (New Jersey) and Fire Island National Seashore (New York). Combined, these models are meant to improve the regional capabilities for predicting climate-change effects on barrier islands and provide resource managers with a common set of tools for adaptation and mitigation of potentially adverse effects of sea-level rise.

Maryland, Virginia↗
USGS2018

An initial comparison of pesticides and amphibian pathogens between natural and created wetlands in the New Jersey Pinelands, 2014–16

A study conducted by the U.S. Geological Survey, in cooperation with the New Jersey Pinelands Commission and Montclair State University, was designed to compare pesticide concentrations and the presence and prevalence of amphibian pathogens between natural ponds and two types of created wetlands, excavated ponds and stormwater basins, throughout the New Jersey Pinelands. The study described herein is part of a larger study by the New Jersey Pinelands Commission designed to compare the functional equivalency of natural and created wetlands throughout the New Jersey Pinelands. Sites were selected on the basis of land-use classifications within a 500-meter radius around each wetland from a pool of natural ponds, excavated ponds, and stormwater basins determined by the New Jersey Pinelands Commission. Water, bed-sediment, anuran-food, and composite larval-anuran-tissue samples were collected from four reference (minimum land-use effects) and four degraded (maximum land-use effects) sites from each wetland type for a total of 24 ponds or basins throughout the New Jersey Pinelands during 2014–16. Prevalence of Ranavirus was determined on the basis of tail clips collected from 60 individual larval anurans in each wetland, and 10 animals from each wetland also were swabbed for the presence of Batrachochytrium dendrobatidis (Bd). Other constituents measured included turbidity, pH, specific conductance, dissolved oxygen, dissolved organic carbon, percent organic carbon in sediment, and composite larval-anuran lipid content. The amount of altered land (percent agricultural plus percent developed) ranged from 0 to 62.4 percent for the natural ponds, 0 to 63.6 percent for the excavated ponds, and 23.3 to 80.2 percent for the stormwater basins. The herbicides atrazine and metolachlor were observed in 60 and 89 percent of the water samples, respectively. The insecticide bifenthrin was the most frequently detected current-use pesticide (greater than 25 percent of the samples) in bed-sediment, anuran-food, and composite larval-anuran-tissue samples. The legacy insecticide p,p' -DDT and its primary degradates p,p' -DDD and p,p' -DDE were the most frequently detected compounds in bed-sediment and anuran-food samples (32–76 percent in sediment samples and 24–72 percent in anuran-food samples). Significantly, greater numbers of pesticides and higher total pesticide concentrations were observed in stormwater basins than in natural and excavated ponds. Reference wetlands had fewer pesticides and lower total pesticide concentrations compared to degraded wetlands, indicating a positive relation between percent altered land and pesticides throughout the New Jersey Pinelands. Ranavirus was observed in larvae from 4 wetlands, including 1 reference natural pond, 1 degraded natural pond, and 2 degraded stormwater basins, with prevalence ranging from 3 to 43 percent. Bd was detected in swabs from 18 animals and in 4 natural ponds (1 reference and 3 degraded), 3 excavated ponds (all reference), and 2 stormwater basins (1 reference and 1 degraded); however, detection probability was low. In the wetlands with Bd detections, between 10 and 30 percent (between 1 and 3) of the animal’s swabbed tested positive for Bd. Owing to the limited number of positive detections for both Bd and Ranavirus , no statistical comparisons between wetland types and land-use classifications were possible.

New Jersey↗