Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Water Resources Bulletin”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21Linked to original sources

Airborne remote sensing for geology and the environment; present and future

In 1988, a group of leading experts from government, academia, and industry attended a workshop on airborne remote sensing sponsored by the U.S. Geological Survey (USGS) and hosted by the Branch of Geophysics. The purpose of the workshop was to examine the scientific rationale for airborne remote sensing in support of government earth science in the next decade. This report has arranged the six resulting working-group reports under two main headings: (1) Geologic Remote Sensing, for the reports on geologic mapping, mineral resources, and fossil fuels and geothermal resources; and (2) Environmental Remote Sensing, for the reports on environmental geology, geologic hazards, and water resources. The intent of the workshop was to provide an evaluation of demonstrated capabilities, their direct extensions, and possible future applications, and this was the organizational format used for the geologic remote sensing reports. The working groups in environmental remote sensing chose to present their reports in a somewhat modified version of this format. A final section examines future advances and limitations in the field. There is a large, complex, and often bewildering array of remote sensing data available. Early remote sensing studies were based on data collected from airborne platforms. Much of that technology was later extended to satellites. The original 80-m-resolution Landsat Multispectral Scanner System (MSS) has now been largely superseded by the 30-m-resolution Thematic Mapper (TM) system that has additional spectral channels. The French satellite SPOT provides higher spatial resolution for channels equivalent to MSS. Low-resolution (1 km) data are available from the National Oceanographic and Atmospheric Administration's AVHRR system, which acquires reflectance and day and night thermal data daily. Several experimental satellites have acquired limited data, and there are extensive plans for future satellites including those of Japan (JERS), Europe (ESA), Canada (Radarsat), and the United States (EOS). There are currently two national airborne remote sensing programs (photography, radar) with data archived at the USGS' EROS Data Center. Airborne broadband multispectral data (comparable to Landsat MSS and TM but involving several more channels) for limited geographic areas also are available for digital processing and analysis. Narrow-band imaging spectrometer data are available for some NASA experiment sites and can be acquired for other locations commercially. Remote sensing data and derivative images, because of the uniform spatial coverage, availability at different resolutions, and digital format, are becoming important data sets for geographic information system (GIS) analyses. Examples range from overlaying digitized geologic maps on remote sensing images and draping these over topography, to maps of mineral distribution and inferred abundance. A large variety of remote sensing data sets are available, with costs ranging from a few dollars per square mile for satellite digital data to a few hundred dollars per square mile for airborne imaging spectrometry. Computer processing and analysis costs routinely surpass these expenses because of the equipment and expertise necessary for information extraction and interpretation. Effective use requires both an understanding of the current methodology and an appreciation of the most cost-effective solution.

Bulletin↗

Stratiform barite deposits in the Roberts Mountains allochthon, Nevada: A review of potential analogs in modern sea-floor environments

The United States is a net importer of barite, a critical mineral for the oil and gas industry; more than 80 percent of current domestic consumption of barite is imported from China. Nearly all of the domestic production of barite comes from stratiform deposits in Nevada. The 'modern analogs' approach adopted in this review can contribute to improving deposit models and the long-term resource picture in the United States. Massive barite deposits in Nevada are interlayered with deep-water siliceous sedimentary strata of Paleozoic age within the Roberts Mountains Allochthon. Although the barite deposits formed along the long-lived, tectonically active margin of western North America before the Antler orogeny, uncertainty still exists regarding key aspects of their genesis, especially with respect to tectonic setting and depositional processes. Proposed tectonic settings include a continental slope adjacent to an ocean basin, and a rifted basin formed on continental crust. A margin dominated by other stress configurations and strike-slip faulting may also have been present during the Paleozoic. Hypotheses for the genesis of sediment-hosted, stratiform barite deposits in Nevada can be grouped into two categories: (1) a synsedimentary hydrothermal model and (2) an ocean-circulation/productivity-zone model. Both models include a stage involving bacterial reduction of seawater sulfate. Disseminated, diagenetic, and hydrothermal barite deposits are widespread features of the modern ocean. In the Pacific Ocean, disseminated barite deposits (max 9 weight percent BaSO4) are forming below high-productivity zones (for example, in equatorial belts) and on the flanks of ocean ridges (as fallout of 'black smoker' particles). Massive barite deposits of diagenetic (in the subsea floor and at cold seeps) and hydrothermal origins are present in several sediment-covered tectonic settings, including ocean ridges (Escanaba Trough and Guaymas Basin), oceanic transform faults (Blanco Fracture Zone), marginal basins (Sea of Okhotsk), convergent margins (Peru, Oregon, Alaska), and transform margins (California Continental Borderland). Both hydrothermal and diagenetic barite deposits may be present in some environments (for example, the California California Borderland). On the basis of a consideration of tectonic settings and a comparison of deposit attributes (associated rock types, size, structure), mineralogy (BaSO4 content, SiO2 content), and geochemistry (S- and Sr-isotopic ratios) for modern and ancient massive barite deposits, cold seeps along transform margins (or, possibly, marginal basins) represent the most promising present-day metallogenetic analogs for stratiform barite. Hydrothermal systems can also produce high-grade barite, but the ubiquity of associated sulfide mineralization on the modern sea floor (and the paucity of sulfides in Nevada deposits) is problematic. On the basis of data from modern barite deposits, the presence of vent-specific faunas (tubeworms) and the variation in d34S values for barite (related to bacterial reduction of seawater sulfate) may not permit discrimination between a diagenetic or hydrothermal origin for ancient barite deposits.

Nevada↗

Geology and ground-water resources of Cerro Gordo County, Iowa

The basic geologic framework underlying Cerro Gordo County consists of an igneous or metamorphic Precambrian basement complex overlain by, in ascending order, consolidated sedimentary rocks of Precambrian, Cambrian, Ordovician, Devonian, Mississippian, and Cretaceous age, and unconsolidated sand, gravel, and clay of Quaternary age. Structurally the county is in the northern part of the Iowan Basin, and the sedimentary units of Cambrian through Devonian age dip southward at 9 to 14 feet per mile. Three major glacial advances, the Nebraskan, Kansan, and Wisconsin, covered all or part of the county during the Pleistocene Epoch and left behind glacial drift consisting of 0 to 125 feet of till and related outwash deposits. De posits of Holocene age, aside from surficial soil, are thin and scattered. Ground water occurs in the sedimentary units of Cambrian through Mississippian age and in the glacial drift and outwash deposits of Quaternary age. The chief aquifers, in ascending order, are the deep Cambrian sandstones, Jordan aquifer, St. Peter Sandstone, Devonian and Mississippian limestones and dolomites, and the Pleistocene glacial drift and related interglacial deposits. Units between the St. Peter Sandstone and the Devonian limestones, the Platteville, Decorah, Galena, and Maquoketa Formations, are of low permeability and are considered to be an aquiclude in comparison to the overlying and under lying units. The deep Cambrian sandstones will yield about 60 gpm (gallons per minute) to an individual well; the Jordan aquifer about 1,200 gpm; the St. Peter Sandstone 30 to 200 gpm; the Devonian limestones and dolomites 120 to 200 gpm; and the glacial outwash or shallow bedrock generally will yield 10 gpm or more. The Jordan aquifer supplies large quantities of water for municipal and industrial use at Mason City. Pumping tests on wells tapping the Jordan in that area show that the aquifer has a transmissibility of about 35,000 gallons per day per foot and a storage coefficient of 2 x 10 -4 Pumping in the Mason City area from 1912 to 1969 has produced about 200 feet of draw down in the areas of maximum withdrawal. Ground water in Cerro Gordo County is of suitable chemical quality for domestic, industrial, or municipal use. The total dis solved solids ranges from 152 mg/l (milligrams per liter) in water from the shallow bedrock to 885 mg/l in water from the deep Cambrian sandstones. Water from the Jordan, which is the most productive aquifer in the county, generally contains less than 500 mg/l dissolved solids. Ground water is the major source of water supplies throughout Cerro Gordo County. The majority of wells in the county are used for domestic and stock supplies, but the largest withdrawals of water are for municipal and industrial supplies. Municipal pumpage in the county in 1968 was about 1.5 billion gallons; industrial pumpage was about 1.8 billion gallons and most of the water was obtained from the Jordan aquifer. If future development of water from the Jordan aquifer is to be to the best economical advantage, careful consideration should be given to the location, capacity, and pumping schedules of proposed wells and nearby existing wells so that local overdevelopment or excessive interference do not occur.

Iowa↗

Geology and ground-water resources of Wichita and Greeley Counties, Kansas

This report describes the geography, geology, and ground-water resources of Wichita and Greeley counties in western Kansas. The area consists of a flat to gently rolling plain, which slopes eastward [at] about 15 feet per mile. A short reach of Ladder Creek (Beaver) is the only perennially flowing stream in the two counties. Ephemeral streams, which flow only during and after heavy rains, are White Woman and Sand Creeks and the western reach of Ladder Creek. The climate is semiarid, the normal annual precipitation being about 17 inches in Wichita County and 16 inches in Greeley County. Agriculture is the principal occupation in the area, and wheat is the most important crop. A considerable area is irrigated; sugar beets and sorghums are the principal irrigated crops. The outcropping rocks range in age from late Cretaceous to Recent; the Smoky Hill chalk member of the Niobrara formation, which is exposed along White Woman Creek in western Greeley County, is the oldest. The Niobrara is almost everywhere overlain by the Ogallala formation of Pliocene age. Generally the Ogallala is overlain by windblown silt of the Pleistocene Sanborn formation, but in places it is exposed along streams. The most recent deposits are dune sand and the alluvium along the streams. The Dakota formation, which is an important aquifer in parts of Kansas, is 300 to 450 feet beneath the Niobrara formation. The ground water that is available to wells in Wichita and Greeley counties is derived entirely from precipitation in the area or in areas immediately west and north. Ground water moves in a generally easterly direction with a gradient that varies inversely with the permeability of the water-bearing beds. The ground-water reservoir is recharged principally by precipitation within the area or within adjacent areas, Ground-water discharge takes place principally by pumping from wells, subsurface outflow, and evaporation and transpiration. Most of the domestic, stock, public, and irrigation supplies are obtained from wells. It is estimated that probably more than 2 billion gallons of water is pumped annually from wells in the area. Since 1947, ground-water recharge has been about equal to ground-water discharge. The use of ground water for irrigation has increased greatly since 1946 and indications are that many more wells may be drilled and pumped without dangerously lowering the water table. Approximately 11,000 to 12,000 acres were irrigated in 1951. A map showing the thickness of water-bearing materials indicates that although much of the area has enough water-bearing material to support irrigation wells, parts of Wichita and Greeley counties have little or none. The Ogallala is the principal water-bearing formation in the area. Small amounts of water may also be obtained locally from alluvial deposits and from cracks in the Niobrara formation. Two deep test wells to the Dakota formation have been drilled but, because of the poor quality of the water, have never been used. The ground water in Wichita and Greeley counties, though hard, is suitable for most purposes. Water from the Ogallala is generally high in fluoride and in some cases may be injurious to the teeth of children. Water from the Dakota, though soft, is unfit for irrigation because of a high content of sodium. The field data upon which most of this report is based are given in tables; they include records of 417 wells, chemical analyses of 31 samples of water, and logs of 57 test holes and wells.

Kansas Geological Survey Bulletin↗

Subsurface geology and oil and gas resources of Osage County, Oklahoma. Part 8, Parts of township 20 north, ranges 9 and 10 east, and township 21 north, ranges 8 and 9 east and all of township 21 north, range 10 east

The area whose subsurface geology and oil and gas resources are described in this report lies along the southern border of Osage County, Okla., and includes parts of T. 20 N., Rs. 9 and 10 E., and of T. 21 N., Rs. 8 and 9 E., and all of T. 21 N., R. 10 E. The towns of Osage and Prue are within the area; Cleveland, which is a mile south of the Arkansas River, is not far beyond its southwestern limit; and Tulsa is 10 miles east of its southeast corner. The production of oil and gas from the many fields in the five townships began as early as 1905, and drilling has continued up to the present. Oil or gas is produced from 13 zones at depths ranging from 250 to 2,600 feet. Of these zones, one is in the Ordovician system, one is at the contact of the Mississippian and the Pennsylvanian series, and all others are in the Pennsylvanian series. The five townships lie within a region that contains many oil and gas fields in the Bartlesville sand; the Red Fork sand is oil-bearing in a narrow belt in T. 21 N., R. 8 E.; and oil and gas are produced in small areas from the Taneha, Skinner, Squirrel, Cleveland, Jones, and Layton sands, the Mussehem and Peoples sand zone, the Okesa, Torpedo, and Clem Creek sand zone, and the Big lime and Peru sand zone. The rocks dip westward across the five townships at an average rate of about 38 feet to the mile as measured on the top of the Oswego lime. This regional dip is interrupted, however, by many anticlines, domes, synclines, and structural basins. The subsurface crests of most of the domes and anticlines are not directly under the crests as determined on the exposed rocks, and the dips of the deeper rocks are steeper and the structural closures greater in the buried rocks than in the exposed rocks. The exposed rocks are cut by several faults that trend northwest, but the data are insufficient to determine whether the deeply buried rocks, also, are displaced along the faults. This investigation has shown that there are a few localities not yet completely tested in this part of Osage County that may produce oil and gas and that a few producing oil fields have areas within or adjacent to them that have not been thoroughly prospected. It is pointed out that yields of oil and gas from limy reservoir rocks may be increased by acid treatment and that additional oil may be produced from some of the reservoir sands by repressuring them with gas or flooding them with water.

Oklahoma↗

Estimating the magnitude of the 100-year peak flow in the Big Lost River at the Idaho National Engineering and Environmental Laboratory, Idaho

Accurate estimates of peak flows in the Big Lost River at the Idaho National Engineering and Environmental Laboratory (INEEL) are needed to assist planners and managers with evaluating possible effects of flooding on facilities at the INEEL. A large difference of 4,350 cubic feet per second (ft 3 /s) between two previous estimates of the magnitude of the 100-year peak flow in the Big Lost River near the western boundary of the INEEL prompted the present study. Regression models that compared annual peak flows and attenuation of annual peak flows between successive gaging stations for the same flow event were used to estimate the magnitude of the 100-year peak flow in the Big Lost River. The 100-year peak flow of 4,790 ft 3 /s at the Howell Ranch gaging station was used as the starting point for this analysis. This estimate was determined by using a three-parameter log-Pearson Type III distribution as outlined in “Guidelines for Determining Flood Flow Frequency” (Bulletin 17B by the Interagency Advisory Committee on Water Data). The regression models indicated that, in the reach of the Big Lost River between Howell Ranch and Mackay Reservoir, downstream peak flows are lower than upstream peak flows. Peak-flow attenuation values for this reach of the river decreased nonlinearly as the magnitude of the peak flow increased. Extrapolation of the trend resulted in an attenuation estimate of 13 percent for this reach relative to the 100-year peak flow at the Howell Ranch gaging station. In the lower reach of the Big Lost River between Mackay Reservoir and Arco, downstream peak flows are also lower than upstream peak flows. However, in contrast to the upper reach, peak-flow attenuation values decreased linearly as the magnitude of the peak flow increased. Extrapolation of the data indicated that peak-flow attenuations in this reach of the river approach zero for flows approaching the 100-year peak-flow estimate immediately upstream and downstream from Mackay Reservoir. A regression model of annual maximum daily mean flows between Arco and the INEEL diversion dam indicated that the attenuation values in this reach of the river are nearly the same for all flows of record. Extrapolation of the linear regression of these values resulted in an attenuation estimate of 10 percent. Seepage measurements made during 1951–53 also resulted in a loss estimate of approximately 10 percent. This attenuation value, combined with the values from analyses of the upstream reaches, resulted in an estimate of the 100-year peak flow for the Big Lost River immediately upstream from the INEEL diversion dam of 3,750 ft 3 /s; upper and lower 95-percent confidence limits were 6,250 ft 3 /s and 1,300 ft 3 /s, respectively. Localized rainfall, even of high intensity, is not likely to produce large peak flows at the INEEL because of high loss rates (infiltration, bank storage, and channel storage) along much of the stream channel. The relatively short flow durations resulting from rainstorms historically have not provided sufficient volumes of water to satisfy local storage demands (bank and channel storage). Only after these storage demands are met do the loss rates decrease enough for significant peak flows to reach the INEEL site. An uncertain component of the present analysis is the effect of seismic activity on the 100-year peak-flow estimate. Analysis of the effect of the magnitude 7.3 Borah Peak earthquake in 1983 on normal flow conditions in the Big Lost River suggests that the joint occurrence of a large earthquake and a 100-year peak flow could significantly increase the magnitude of the peak flow at the INEEL.

Idaho↗

Geology and ground-water resources of the island of Niihau, Hawaii

Niihau lies 17 1 / 2 miles southwest of Kauai. Its area is 72 square miles, and its highest point has an altitude of 1,281 feet. The population is about 180, chiefly Hawaiians. The annual rainfall at Kiekie, the ranch headquarters, generally ranges between 18 and 26 inches. The chief industries are the raising of sheep and cattle and production of honey. The island is privately owned. The main mass of the island is composed of a deeply weathered remnant of a basalt dome of Tertiary age, cut by a dike complex trending NE-SW. These Tertiary rocks are herein named the Paniau volcanic series. The central vent lay about 2 miles out to sea to the east of the present island. The dome, after deep gulches were cut into it by stream erosion and it was cliffed all around by the sea, was partly submerged. During Pleistocene time a broad wave-cut platform on the north, west, and south sides was built above sea level and widened by the eruption of lavas and tuffs, from 9 vents now visible and other vents now buried, to form a low coastal plain. These Pleistocene volcanic rocks are named the Kiekie volcanic series. Ash from Lehua Island, a Pleistocene tuff cone, has been drifted into duties on the north end of Niihau. Lithified dunes that extend below sea level, and the small outcrops of emerged fossiliferous limestone above sea level, indicate the plus 100-foot, minus 60-foot, plus 25-foot, and plus 5-foot eustatic stands of the sea correlative with changes in the volume of the polar ice caps and concurrent changes in the configuration of ocean basins. Calcareous dune and beach deposits, short stretches of nullipore reef and beach rock, and playa and alluvial deposits constitute the Recent rocks. No perennial streams exist on the island but about a dozen playa lakes, fresh or brackish during rainy weather, lie on the plain. The domestic water supply is rain caught from roofs. Only three wells on the island yield water with less than 25 grains of salt per gallon (260 parts per million of chloride). Typically, water holes for stock are about 15 feet across, 5 feet deep, and 8 feet wide. They have been dug in the lowlands where the depth to water is usually less than 5 feet. Forty-six dug wells and water holes exist, the water of some of which has become too salty for stock. Two or three deep wells were drilled 500 to 1,000 feet below sea level, but they encountered salty water. Three wells, not yet used, have been excavated in the Tertiary basalts. One of them has an infiltration tunnel at the bottom. Two seeps perched on vitric tuff beds more than 500 feet above sea level carry large quantities of salt leached from spray that falls on their recharge areas. Several sites are recommended for developing additional water for stock. The island, however, will always be short of domestic water because of aridity, unfavorable geologic structures, continuous deposition of salt spray, and abundant authigenic salts in the lake beds. Among the lavas of the Paniau volcanic series, of Tertiary age, olivine basalts probably predominate but ordinary basalts are abundant. Picrite-basalt of the primitive type, containing abundant olivine phenocrysts, also occurs. Andesites are probably present but are rare. Most of the lavas of the Kiekie volcanic series, of Pleistocene age, are olivine basalt, but one is transitional between olivine basalt and picrite-basalt. In many of the Pleistocene lavas the late-crystallized augite is titanian. A single occurrence of melilite-nepheline basalt has been reported. Chemical analyses of five rocks are listed.

Hawaii↗

Iron-ore resources of the United States including Alaska and Puerto Rico, 1955

The importance of iron ore, the basic raw material of steel, as a fundamental mineral, resource is shown by the fact that about 100 million long tons of steel is used annually in the economy of the United States, as compared with a combined total of about 5 million long tons of copper, lead, zinc, and aluminum. Satisfying this annual demand for steel requires about 110 million tons of iron ore and 70 million tons of scrap iron and steel. The average annual consumption of iron ore in the United States from 1951 to 1955, inclusive, was about 110 million long tons, which is about twice the annual average from 1900 to 1930. Production of iron ore in the United States in this 5-year period averaged approximately 100 million long tons annually, divided by regions as follows (in percent): Lake Superior, 84.1; southeastern, 6.7; western, 6.7; northeastern, 1.4; and central and gulf, 1.1. Mining of iron ore began in the American Colonies about 1619, and for 225 years it was limited to eastern United States where fuel and markets were readily available. Production of iron ore from the Lake Superior region began in 1846; the region became the leading domestic source by 1890, and the Mesabi range in Minnesota has been the world's most productive area since 1896. Proximity of raw materials, water transportation, and markets has resulted in centralization of the country's iron and steel industry in the lower Great Lakes area. Increased imports of iron ore being delivered to eastern United States as well as demands for steel in nearby markets have given impetus to expansion in the steel-making capacity in this area. The four chief iron-ore minerals - hematite, liminite, magnetite, and siderite - are widely distributed but only locally form deposits of sufficient tonnage and grade to be commercially valuable at the present time. The iron content of these minerals, of which hematite is the most important, ranges from 48 percent in siderite to 72 percent in magnetite, but as these minerals are associated with other rock-forming minerals, the iron content of marketable ore has a lower range from 30 to 67 percent. Chemical constituents other than iron also are important in determining the marketability of iron ore. Although some iron ores can be used in the blast furnace as mined, others must first be improved either chemically by reduction of undesirable constituents, or physically by aggregation. Phosphorus and sulfur particularly are common deleterious elements; excessive silica is also undesirable but within certain limits can be controlled by additional flux. Lime and magnesia are beneficial in specified amounts because of their fluxing qualities, and a small amount of alumina improves the fluidity of slag. Manganese is especially desirable as a deoxidizing and desulfurizing agent. Titanium, chromium, and nickel must also be considered in the use of ore containing these elements. The principal iron-ore deposits in the United States have been formed by three processes. Hematite-bearing bedded deposits such as those at Birmingham, Ala., are marine sedimentary rocks which, except for weathering along the outcrop, have remained practically unaltered since deposition. Deposits of the Lake Superior region, also in sedimentary strata, originally had a slightly lower iron content than those at-Birmingham, but ore bodies of hematite and limonite were formed by removal of other constituents in solution after deposition of the beds, with a relative increase of iron content in the material remaining. Limestone adjacent to igneous intrusions has been replaced by magnetite deposits at Cornwall, Pa., and by hematite-magnetite deposits near Cedar City, Utah. Magnetite deposits in New Jersey and in the Adirondack Mountains of New York are generally believed to have been formed by replacement of grains of other minerals in metamorphic rocks. Iron-ore resources are made up of reserves of iron ore, material usable under existing economic and technologic conditions; and potential ore, material likely to become usable under more favorable conditions. The tonnage and grade of material of combined reserves and potential ore in each of the deposits known or believed to contain at least 200,000 long tons of iron-ore resources are tabulated in this report, and numerous sources of additional information are given in a selected bibliography. The total domestic iron-ore resources are estimated at approximately 75,000 million long tons of crude ore. About 10,000 million tons of the resources is reserves of crude ore that will probably yield 5,500 million tons of concentrates and direct-shipping ore. About 65,000 million tons is potential ore and may yield 25,000 million tons of concentrates and some direct-shipping ore.

Bulletin↗

Geology and ground-water resources of the island of Molokai, Hawaii

The island of Molokai is the fifth largest of the Hawaiian Islands, with an area of 250 square miles. It lies 25 miles southeast of Oahu, and 8.5 miles northwest of Maui. It consists of two principal parts, each a major volcanic mountain. East Molokai rises to 4,970 feet altitude. It is built largely of basaltic lavas, with a thin cap of andesites and a little trachyte. The volcanic rocks of East Molokai are named the East Molokai volcanic series, the basaltic part being separated as the lower member of the series, and the andesites and trachytes as the upper member. Large cinder cones and bulbous domes are associated with the lavas of the upper member. Thin beds of ash are present locally in both members. The lavas of the lower member are cut by innumerable dikes lying in two major rift zones trending eastward and northwestward. A large caldera, more than 4 miles long, and a smaller pit 0.8 mile across existed near the summit of the volcano. The rocks formed in and under the caldera are separated on plate 1 as the caldera complex. Stream erosion has cut large amphitheater-headed valleys into the northern coast of East Molokai, exposing the dikes and the caldera complex. West Molokai is lower than East Molokai, rising to 1,380 feet altitude. It was built by basaltic lavas erupted along rift zones trending southwestward and northwestward. Many of the flows were unusually fluid. The volcanic rocks of West Molokai Volcano are named the West Molokai volcanic series. Along its eastern side, the mountain is broken by a series of faults along which its eastern edge has been dropped downward. West Molokai Volcano became extinct earlier than East Molokai Volcano, and its flank is partly buried beneath lavas of East Molokai. Both volcanic mountains were built upward from the sea floor probably during Tertiary time. Following the close of volcanic activity stream erosion cut large canyons on East Molokai, but accomplished much less on drier West Molokai. Marine erosion attacked both parts of the island, producing high sea-cliffs on the windward coast. In late Tertiary or early Pleistocene time the island was submerged to a level at least 560 feet above the present shore line, then reemerged. Later shifts of sea level, probably partly resulting from Pleistocene glaciation and deglaciation, ranged from 300 feet below to 100 feet or more above present sea level. Marine deposits on the southern slope extend to an altitude of at least 200 feet. Eruption of the Kalaupapa basalt built a small lava cone at the foot of the northern cliff, forming Kalaupapa peninsula; and a small submarine eruption off the eastern end of Molokai built the Mokuhooniki tuff cone, the fragments of which now form Hooniki and Kanaha Islands. Deposition of marine and fluviatile sediments has built a series of narrow flats close to sea-level along the southern coast. Nearly the entire island is underlain, close to sea level, by ground water of the basal zone of saturation. Beneath West Molokai, the Hoolehua Plain between West and East Molokai, and the southern coastal area of East Molokai, the basal water is brackish. Beneath much of East Molokai, fresh basal water is obtainable. Small amounts of fresh water are perched at high levels in East Molokai by thin poorly permeable ash beds. Fresh water is confined at high levels in permeable compartments between poorly permeable dikes in the rift zones of East Molokai, and can be developed by tunnels. Projects to bring the abundant surface and ground water of the large wind ward valleys to the Hoolehua Plain are described. Future developments are suggested. All wells and water-development tunnels are described in tables.

Hawaii↗

Developing an outcome-based biodiversity metric in support of the field to market project: Final report

Our objective was to create a metric that would calculate the relative impact of common commercial agricultural practices on terrestrial vertebrate richness. We sought to define impacts in fields (including field borders) of the southeastern region’s commercial production of corn, wheat, soy, and cotton. The metric is intended to serve as an educational tool, allowing producers to see how operational decisions made at the field level impact overall vertebrate species richness and to explore decision impacts to targeted species groups (e.g. game, pest, or beneficial species). Agricultural landscapes are often mistakenly thought to be unsuitable habitat for most species. However, as demonstrated by results reported here, even large-scale, conventional agricultural producers are potentially important partners in biodiversity conservation. Many vertebrate species do inhabit agricultural landscapes, benefitting from the provision of water, food, or shelter within cultivated fields and their immediate borders (e.g., Holland et al. 2012). In the Southeastern US, of the 613 terrestrial vertebrate species modeled by the Southeast Gap Analysis Program (SEGAP) (http://www.basic.ncsu.edu/segap/index.html), 263 utilize row crop and associated agricultural land cover classes as potential habitat (Box 1). While some species may be sensitive to certain operational practices (e.g., tillage, pest management, or field border management practices), others are generally tolerant, and some may benefit either directly or indirectly. For example, field margins and ditches often serve as semi-natural habitats providing foraging resources and shelter for vertebrates and are shown to positively influence species richness and abundance (Billeter et al. 2007; Herzon & Helenius 2008; Marshall & Moonen 2002; Shore et al. 2005; Weibull et al. 2003; Wuczyńskia et al. 2011). Biodiversity responses are, therefore, complex, as an individual species’ responses to agricultural production practices depends on that animal’s resource specialization, mobility, and life history strategies (Jeanneret et al. 2003a, b; Jennings & Pocock 2009). The knowledge necessary to define the biodiversity contribution of agricultural lands is specialized, dispersed, and nuanced, and thus not readily accessible. Given access to clearly defined biodiversity tradeoffs between alternative agricultural practices, landowners, land managers and farm operators could collectively enhance the conservation and economic value of agricultural landscapes. Therefore, Field to Market: The Keystone Alliance for Sustainable Agriculture and The Nature Conservancy jointly funded a pilot project to develop a biodiversity metric to integrate into Field to Market’s existing sustainability calculator, The Fieldprint Calculator (http://www. fieldtomarket.org/). Field to Market: The Keystone Alliance for Sustainable Agriculture is an alliance among producers, agribusinesses, food companies, and conservation organizations seeking to create sustainable outcomes for agriculture. The Fieldprint Calculator supports the Keystone Alliance’s vision to achieve safe, accessible, and nutritious food, fiber and fuel in thriving ecosystems to meet the needs of 9 billion people in 2050. In support of this same vision, our project provides proof-of-concept for an outcome-based biodiversity metric for Field to Market to quantify biodiversity impacts of commercial row crop production on terrestrial vertebrate richness. Little research exists examining the impacts of alternative commercial agricultural practices on overall terrestrial biodiversity (McLaughlin & Mineau 1995). Instead, most studies compare organic versus conventional practices (e.g. Freemark & Kirk 2001; Wickramasinghe et al. 2004), and most studies focus on flora, avian, or invertebrate communities (Jeanneret et al. 2003a; Maes et al. 2008; Pollard & Relton 1970). Therefore, we used an expert-knowledge-based approach to develop a metric that predicts expected impacts to shelter and forage resources, individual species, and overall biodiversity (species richness). This approach is modeled after an ecosystems services concept (WRI 2005), except that we examine services (i.e., resources) provided to vertebrate wildlife rather than service provided to the human population. SEGAP predicts species that are potentially present in an area given landscape-scale habitat availability, configuration, and context (e.g., patch size, proximity to resources, connectivity, potential for disturbance). Based on the prediction of species that may be potentially present, the impacts of management decisions within fields and around their borders can be analyzed based on the impact of those practices to the availability of species’ resources. The final metric provides an index of a producer’s relative impact, but perhaps even more importantly, the underlying database allows producers to explore details such as which species are most impacted or how alternative decisions would impact their score.

Technical Bulletin↗

Geology and ground-water resources of Linn County, Iowa

Linn County, in east-central Iowa, covers about 713 square miles and lies in the Western Young Drift section of the Central Lowlands physiographic province. The normal annual rainfall in the county is about 88 inches and the annual mean temperature is about 48°F. The population in 1960 was 136,899, of which 75 percent was urban. Ground water is a vital natural resource in Linn County-all municipal, farm-domestic, livestock, and most industrial supplies are obtained from this source. An estimated 24 mgd (million gallons per day) of ground water was used in the county in 1964. The principal aquifers are alluvium, buried channel deposits, Silurian-Devonian limestones and dolomites, and the Jordan Sandstone. All yield fair-to-good quality water, although the water is hard and locally contains high concentrations of iron. All are capable of yielding as much as 500 gallons or more per minute to wells. Alluvium has been developed for water supplies only at Cedar Rapids, where withdrawals in 1964 averaged 12 mgd for municipal supplies and 2.7 mgd for industrial supplies. The alluvial aquifer yields up to 2,000 gpm (gallons per minute) to wells in the Cedar Rapids well field. Similar yields from alluvium may be available along several reaches of the Cedar and Wapsipinicon Rivers. Smaller quantities are available from the alluvium of Prairie Creek. Alluvial aquifers are readily recharged by precipitation and induced infiltration. Buried channel deposits occur in preglacial or interglacial valleys that were carved into the bedrock. These old valleys, whose trends roughly parallel the present Cedar River and Prairie Creek, contain water-bearing alluvial deposits that are covered by glacial drift. Data from a few wells tapping these deposits indicate that yields of up to 500 gpm of good-quality water are available from this source. The most favorable areas for development of water supplies are those areas where the channel deposits underlie and receive recharge from the alluvium of the Cedar River and Prairie Creek. The Silurian-Devonian aquifer's county-wide occurrence, near-surface position, and ability to yield as much as several hundred gallons per minute of good-quality water makes it the most widely used aquifer in Linn County. During 1960-64, withdrawals averaged about 1.5 mgd for domestic-livestock use, about 0.6 mgd for small community use, and about 4 mgd for industrial-commercial use. Withdrawals are concentrated in the Cedar Rapids area, where 65 percent of the withdrawals from the aquifer occur. This concentrated pumpage has caused a progressive lowering of the aquifer's piezometric surface in downtown Cedar Rapids. During the past 70 years, water levels in wells in this locality have declined about 105 feet in the center of the cone of depression and about 26 feet about one mile from the cone's center. Water level in the center of the cone presently is declining at an average rate of 1 foot per year. Because the rate of decline in the same area was determined to have been 2 to 3 feet per year during the 1940's and 50's, the cone is believed to be stabilizing or pumpage is being reduced. The aquifer probably could withstand an additional 150 to 200 feet of piezometric lowering in the Cedar Rapids area, but individual wells would be adversely affected. The Jordan aquifer, which underlies the entire county, is considered to be the most isotropic and homogeneous aquifer in Linn County. Yields of 1,000 gpm or more of fair-to-good quality water from this source are believed to be available anywhere in the county. The aquifer is not yet developed extensively; an average of about 2.4 mgd was pumped during 1964 for industrial and municipal use in the Cedar Rapids-Marion area. The shallow bedrock and glacial drift aquifers yield only small quantities of good quality water. Their widespread extent and shallow depth, however, make them suitable for the development of small supplies for domestic and livestock use.

Iowa↗

Geology and Mineral Resources of the East Mojave National Scenic Area, San Bernardino County, California

The rocks of the East Mojave National Scenic Area (EMNSA) record a history of dynamic geologic events that span more than 1,800 million years (m.y.). These geologic events contributed significantly to development of the spectacular vistas and panoramas present in the area today. The oldest rocks underlie much of the northern part of the EMNSA. These rocks were subjected to extreme pressures and temperatures deep in the Earth's crust about 1,700 million years ago (Ma). They were subsequently intruded by granitic magmas from about 1,695 to 1,650 Ma, by additional granitic magmas at about 1,400 Ma and, later, at about 1,100 Ma, by iron-rich magmas that crystallized to form dark igneous rocks termed diabase. Unusual potassium- and magnesium-rich rocks, emplaced at about 1,400 Ma, crop out in a few places within and near the EMNSA. Their distinctive composition results from very small degrees of partial melting of mantle peridotite that was highly enriched in incompatible trace elements. At Mountain Pass, just outside the northeast boundary of the EMNSA, the potassium- and magnesium-rich rocks are accompanied by a rare type of carbonatite, an igneous rock composed of carbonate minerals, that contains high-grade rare earth element mineralization. Subsequent to these igneous-dominated events, sedimentary strata began to be deposited at about 1,000 Ma; mostly sandstone and shale were deposited initially in marine and, less commonly, in continental environments along the west edge of the core of the North American continent. Sedimentation eventually culminated in the widespread deposition of thick marine limestones from about 400 to about 245 Ma. These limestones represent a continental-shelf environment where shallow-water limestone formed to the east and deeper water limestone formed to the west. The end of the formation of these sedimentary deposits probably was caused by uplift of the shelf, which marked the beginning of a long period of tectonic upheaval. At about 170 Ma, widespread emplacement of coarse-grained granitic magmas began again in the region; some of these magmas also erupted as volcanic rocks. Additional episodes of magmatism took place at about 100 Ma and at 75 Ma. Most of the metallic-mineral occurrences in the EMNSA are associated with the igneous rocks that range in age from 170 to 75 Ma. During each of these magmatic events, the previously deposited sedimentary strata were buckled and broken as the entire region, part of a continental-scale fold and thrust belt, underwent crustal shortening and compression. A period of tectonic quiescence characterized the region from about 65 Ma to about 20 Ma. The quiet period ended abruptly with widespread volcanism along the southern and eastern parts of the EMNSA. The major gold deposits in the Castle Mountains are associated with this episode of volcanism. During this volcanic outburst, the crust extended laterally in several areas that border the EMNSA: along the lower Colorado River 65 km to the east, in the Kingston Range 20 km to the north, and in the central Mojave Desert 75 km to the southwest. This extensional deformation is characterized by the superposition of upper-crustal rocks over midcrustal rocks along large flat-lying faults, several of which project beneath rocks now exposed at the surface in the EMNSA. The near-surface rocks of the EMNSA, however, apparently escaped much of this intense extensional deformation. High-angle faults, which cut several of the mountain ranges, possibly have undergone several periods of movement, which date back to approximately 70 to 100 Ma. Some faults are of local importance to the physiographic development of the mountain ranges and intervening basins, and, in places, the faults seem to have localized various kinds of ore bodies and mineral occurrences. Volcanism and extensional deformation waned from 14 to 11 Ma. By approximately 10 Ma, widespread erosion had produced broad erosional dome-shaped mountains in the n

Bulletin↗

Uranium provinces of North America — Their definition, distribution, and models

Uranium resources in North America are principally in unconformity-related, quartz-pebble conglomerate, sandstone, volcanic, and phosphorite types of uranium deposits. Most are concentrated in separate, well-defined metallogenic provinces. Proterozoic quartz-pebble conglomerate and unconformity-related deposits are, respectively, in the Blind River–Elliot Lake (BRELUP) and the Athabasca Basin (ABUP) Uranium Provinces in Canada. Sandstone uranium deposits are of two principal subtypes, tabular and roll-front. Tabular sandstone uranium deposits are mainly in upper Paleozoic and Mesozoic rocks in the Colorado Plateau Uranium Province (CPUP). Roll-front sandstone uranium deposits are in Tertiary rocks of the Rocky Mountain and Intermontane Basins Uranium Province (RMIBUP), and in a narrow belt of Tertiary rocks that form the Gulf Coastal Uranium Province (GCUP) in south Texas and adjacent Mexico. Volcanic uranium deposits are concentrated in the Basin and Range Uranium Province (BRUP) stretching from the McDermitt caldera at the Oregon-Nevada border through the Marysvale district of Utah and Date Creek Basin in Arizona and south into the Sierra de Peña Blanca District, Chihuahua, Mexico. Uraniferous phosphorite occurs in Tertiary sediments in Florida, Georgia, and North and South Carolina and in the Lower Permian Phosphoria Formation in Idaho and adjacent States, but only in Florida has economic recovery been successful. The Florida Phosphorite Uranium Province (FPUP) has yielded large quantities of uranium as a byproduct of the production of phosphoric acid fertilizer. Economically recoverable quantities of copper, gold, molybdenum, nickel, silver, thorium, and vanadium occur with the uranium deposits in some provinces. Many major epochs of uranium mineralization occurred in North America. In the BRELUP, uranium minerals were concentrated in placers during the Early Proterozoic (2,500–2,250 Ma). In the ABUP, the unconformity-related deposits were most likely formed initially by hot saline formational water related to diagenesis (»1,400 to 1,330 Ma) and later reconcentrated by hydrothermal events at »1,280–»1,000, »575, and »225 Ma. Subsequently in North America, only minor uranium mineralization occurred until after continental collision in Permian time (255 Ma). Three principal epochs of uranium mineralization occurred in the CPUP: (1) » 210–200 Ma, shortly after Late Triassic sedimentation; (2) »155–150 Ma, in Late Jurassic time; and (3) » 135 Ma, after sedimentation of the Upper Jurassic Morrison Formation. The most likely source of the uranium was silicic volcaniclastics for the three epochs derived from a volcanic island arc at the west edge of the North American continent. Uranium mineralization occurred during Eocene, Miocene, and Pliocene times in the RMIBUP, GCUP, and BRUP. Volcanic activity took place near the west edge of the continent during and shortly after sedimentation of the host rocks in these three provinces. Some volcanic centers in the Sierra de Peña Blanca district within the BRUP may have provided uranium-rich ash to host rocks in the GCUP. Most of the uranium provinces in North America appear to have a common theme of close associations to volcanic activity related to the development of the western margin of the North American plate. The south and west margin of the Canadian Shield formed the leading edge of the progress of uranium source development and mineralization from the Proterozoic to the present. The development of favorable hosts and sources of uranium is related to various tectonic elements developed over time. Periods of major uranium mineralization in North America were Early Proterozoic, Middle Proterozoic, Late Triassic–Early Jurassic, Early Cretaceous, Oligocene, and Miocene. Tertiary mineralization was the most pervasive, covering most of Western and Southern North America.

Bulletin↗

Geology and ground-water resources of the islands of Lanai and Kahoolawe, Hawaii

Lanai lies 59 miles southeast of Honolulu, Oahu, has an area of 141 square miles, and is 3,370 feet high. (See fig. 1 and pl. 1.) Lanai City is the only town of importance. The island produces pineapples and cattle. The surface above about 1,200 feet is generally covered with lateritic soil, which reaches a maximum depth of about 50 feet. Below this level the island is partly devoid of vegetation and is strewn with boulders, the result of having been once submerged by the ocean to this depth. Traces of various emerged and submerged shore lines are described, the highest fossiliferous marine deposits being 1,070 feet above sea level. Lanai is an eroded extinct basaltic volcano built during one period of activity. No secondary eruptions occurred as on most of the other islands. It has three rift zones and a summit caldera. The summit plateau has resulted from collapse along the northwest rift zone. Elsewhere there is much evidence of faulting. About 100 faults and 275 dikes were recorded, but they are so close together in places that it was not possible to show them all on the map. The climate is semitropical, the mean annual temperature of Lanai City, altitude 1,620 feet, being 68° F. Because Lanai lies to the lee of Maui Island it is dry. The mean annual rainfall ranges from 38 inches on the summit to less than 10 inches on the coast. The windward (northeast) side is carved by streams into deep canyons. Maunalei Gulch has the only perennial stream, and it does not reach the sea. Ground water, the lifeblood of Lanai is scarce. Lanai City obtains some of its water supply by a tunnel from gravel in Maumalei Gulch. This water apparently rises from the dike complex in this gulch. The rest of the supply comes from a recently constructed shaft tapping the dike complex not far downstream. The total quantity of high-level ground water discharged by springs and tunnels ranges from about 600,000 gallons a day in wet weather to about 250,000 gallons a day in dry weather. The basal water, although potable, is fairly high in salt. Several sites are recommended for developing and conserving ground water. Kahoolawe Island is 11 miles long, 6 miles wide, 1,491 feet high, covers 45 square miles, and lies 94 miles southeast of Honolulu and 6 3 / 4 miles southwest of Maui. It is a shield-shaped extinct volcano composed chiefly of thin flows of primitive basalt poured in rapid succession from three rift zones and a vent at their intersection. At one stage the volcano was indented with a caldera about 3 miles across which was later completely filled. A graben led southwestward from it. The rocks are divided into Late Tertiary (?) or early Pleistocene(?) pre-caldera basalts, caldera-filling basalts and basaltic andesites, post-caldera basalts and andesites, and Recent post erosional basalts. A few thin vitric tuff beds and cinder cones were found. Marine erosion has cut cliffs as high as 800 feet along the east and south shores and exposed a cross section of the caldera. Only shallow ephemeral gulches exist. The entire summit has been eroded to a hard-pan surface by the wind as a result of the vegetation being destroyed by livestock. The island is semi-arid and well water is needed for stook: "The stook is now supplied entirely from storage of rain and flood waters. During droughts water is hauled by boat from the island of Maui. All the wells dug so far yield water that is too brackish for stock except at the fairly inaccessible south side of Kanapou Bay. The resistivity survey indicates a water table 1.5 feet or less above sea level for 2.25 miles inland. A few sites for wells are recommended in the dike complex where small supplies of water suitable for stock might be found. Petrographic studies by Gordon A. Macdonald indicate that the pre-caldera and caldera-filling lavas are largely normal olivine basalt of the type which forms the bulk of all Hawaiian volcanoes thus far investigated. It represents the undifferentiated magma of the Hawaiian petrographic province. Toward the close of the caldera-filling epoch the vent became less active, and magmatic differentiation produced basaltic andesites, which are interbedded with normal basalts. The post-caldera lavas are largely basaltic andesites and andesites. The much younger lavas, erupted after a period of extensive erosion, are olivine basalts similar in composition to the pre-caldera flows. The mineralogy of the Kahoolawe rocks is described in detail.

Hawaii↗

Groundwater flow model for Western Chippewa County–Including analysis of water resources related to industrial sand mining and irrigated agriculture

A groundwater flow model for western Chippewa County, Wisconsin, was developed by the Wisconsin Geological and Natural History Survey (WGNHS) and the U.S. Geological Survey (USGS) using the computer program MODFLOW. The model is the result of a five-year groundwater study commissioned by Chippewa County in 2012 to evaluate the effects of industrial sand mining and irrigated agriculture on the county’s water resources. The study incorporates existing data and newly acquired data from fieldwork conducted within the study area. The groundwater model may be useful for future investigations, such as evaluation of proposed high-capacity well sites, development of municipal wellhead protection plans, and studies that seek to further quantify surface water-groundwater relationships. The model conceptualizes the hydrostratigraphy of western Chippewa County as six stacked layers. Each layer is distinct, beginning with unlithified glacial material at the surface, and alternating between sandstones (that act as aquifers) and shale units (that serve as aquitards). The model is bounded below by Precambrian crystalline bedrock and its perimeter was derived from a regional-scale groundwater flow model. The MODFLOW model represented average conditions during 2011–2013 with “steady-state” assumptions, meaning that simulated water levels do not fluctuate seasonally or from year to year. Steady-state models simplify natural variability, making results of scenario simulations easier to interpret and compare while also maximizing effects of stressors because the simulated stress is always applied (not halted after a few months or years). Model calibration used the parameter estimation code (PEST), and calibration targets included heads (groundwater levels) and streamflows. Calibration focused on 2011–2013 because a large amount of head and streamflow data were available for that period. The MODFLOW model explicitly simulates all sources and sinks of water, including groundwater/surface-water interaction with streamflow routing. Model input included estimates of aquifer hydraulic conductivity and a spatial groundwater recharge distribution developed using a GIS-based soil-water-balance (SWB) model applied to the model area. Groundwater withdrawals were simulated for 269 high-capacity wells across the entire model domain, which includes western Chippewa County and adjacent portions of Dunn, Barron, and Rusk Counties. Collectively, these wells withdrew about 1.14 million gallons per year between 2011 and 2013. Once the model was calibrated, it was applied to two distinct scenarios of increased groundwater withdrawals: one evaluating hydrologic effects of more intensive industrial sand mining and the second evaluating the hydrologic effects of more intensive agricultural irrigation practices. Each scenario was developed with input from Chippewa County and a stakeholder group established expressly for this study. The scenarios were designed to represent reasonable future buildout conditions for both mining and irrigated agriculture. The mining scenario underscores the potential hydrologic effects related to changing land-use practices (i.e., hilltops and farmland becoming sand mines), while the irrigated agriculture scenario illustrates the potential hydrologic effects of intensifying existing land-use practices (i.e., installing new wells to irrigate farm fields). While each scenario evaluated distinctly different conditions, modeling results demonstrated the potential of both scenarios to lower the water table and reduce baseflows in headwater streams within the modeled area. In the case of irrigated agriculture, hydrologic effects were associated directly with groundwater withdrawals. By assuming that irrigation did not decrease, this steady-state simulation represented a sustained future effect. By contrast, hydrologic effects of industrial sand mining were the result of both groundwater withdrawals at mines and land-use changes that effectively reduced recharge to groundwater over distinct phases of active mining. This scenario included a post-mining phase, during which groundwater withdrawals stopped and mined areas were reclaimed to undeveloped prairie grass cover. If reclamation to undeveloped prairie indeed occurs as simulated, long-term increases in the water table and stream baseflows are possible. In this sense, the scenario representing build out of irrigated agriculture led to long-term baseflow declines while the future buildout of industrial sand mining led to declines that dissipated following mine reclamation to undisturbed prairie. Future investigations in similar hydrogeologic settings may find the following insights gleaned from this study useful: ❚❚ The characterization of hydrogeologic properties, delineation of hydrogeologic units, and calibration of groundwater flow models benefited from incorporation of accurate well construction reports, high-quality borehole geophysical logs, and streamflow gaging data. ❚❚ Infiltration testing performed in active mining areas provided evidence that reducing the degree and extent of compaction and enhancing areas designed to retain and infiltrate stormwater runoff could potentially reduce runoff and increase groundwater recharge. ❚❚ Similarly, reclaiming mined areas to prairie grasses would be expected to reduce runoff and increase groundwater recharge by reducing compaction and improving soil structure and vegetation that can slow runoff and enhance infiltration.

Wisconsin↗

Hydrogeology and simulation of groundwater flow in Columbia County, Wisconsin

This report describes the regional hydrogeology and groundwater resources of Columbia County, Wisconsin, and documents a regional groundwater flow model developed for the county. Regional hydrostratigraphic units include the unlithified aquifer, the upper bedrock aquifer, and the Elk Mound aquifer. The unlithified aquifer consists of deposits that range in composition from sand and gravel outwash and stream deposits to silty, sandy till. This aquifer is less than 25 ft thick in much of eastern Columbia County, but consists of permeable sand and gravel extending to over 250 ft in depth in the Wisconsin River valley bottom. The upper bedrock aquifer consists of Ordovician and upper Cambrian sedimentary formations, including sandstone, siltstone and dolomitic strata. The upper bedrock aquifer underlies the unlithified aquifer in eastern portions of the County, but is absent to the west, where these formations are largely eroded. The contact between the Tunnel City Group and Wonewoc Formation (Top of Elk Mound Group) forms the base of the upper bedrock aquifer. Bedding plane fractures are common to this aquifer, although only a portion of the observed fractures appear to be hydraulically active. The upper bedrock aquifer is a significant source of groundwater at a regional scale. Measurements of hydraulic head showed a difference of several feet across the bottom of this aquifer to the underlying Wonewoc sandstone, indicating that the basal facies of the Tunnel City Group functions as an aquitard separating the upper bedrock aquifer from the Elk Mound aquifer. Conditions vary considerably within this aquifer, depending on the local lithostratigraphy. For example, where present, the St. Lawrence Fm. and fine-grained intervals of the Tunnel City Group may be locally-extensive aquitards. The Elk Mound aquifer consists of Cambrian sandstone of the Wonewoc, Eau Claire, and Mount Simon Formations. It is thin to absent in several locations but ranges up to 600 ft in thickness over much of southern Columbia County. The variation in thickness is due in large part to the irregular topography of the underlying Precambrian crystalline rock, which generally serves as the base of the groundwater system. In neighboring counties, a fine-grained facies within the Eau Claire Fm. acts as a regionally extensive aquitard, referred to as the Eau Claire aquitard. Much of the data collected and compiled for this study suggest that shale or dolomite within the Eau Claire Fm., which is the equivalent of the Eau Claire aquitard, occurs only within southwestern Columbia County. There is little to no evidence of the Eau Claire aquitard over most of the county. Where the dolomite and shale are absent, the Elk Mound aquifer is relatively homogenous and does not include a mappable aquitard. A three-dimensional steady-state flow model presented here represents long-term, average conditions in the regional groundwater system since about 1970. The model was constructed with the U.S. Geological Survey’s MODFLOW-NWT code; it has six layers with a uniform grid of 300 ft x 300 ft cells. Layers 1 and 2 simulate the unlithified aquifer and layer 3 represents the upper bedrock aquifer. The Elk Mound aquifer is simulated by layers 4, 5 and 6, representing the Wonewoc, Eau Claire, and Mount Simon Formations, respectively. The model extends beyond the boundaries of Columbia County to ensure that hydrologic conditions simulated within the County are consistent with regional conditions. Recharge to the groundwater flow model is based on results from a GIS-based soil-water-balance model. Recharge was simulated with the unsaturated zone flow (UZF) package in MODFLOW. This approach is particularly useful for quantifying groundwater discharge to riparian wetlands because UZF tracks recharge that would lead to the simulated water table exceeding the land surface (represented by the top of model layer 1) and reroutes it to nearby stream segments. The model includes pumping from 256 wells, and 178 of these are located within Columbia County. Pumping totaled about 28 million gallons per day (mgd) on average since 1970, with 7.2 mgd of the withdrawal from within the County. Model calibration was performed with the PEST parameter estimation code. Calibration targets included approximately 3,900 head measurements and 91 stream flow measurements. Four vertical-head differences across hydrogeologic units, calculated from data collected during packer testing in wells in Columbia County, were also used in model calibration. Results from the calibrated model provide a groundwater balance for the region. About 83 percent of groundwater originates as recharge to the water table, 12 percent comes from leakage from streams, and about 5 percent of the groundwater flows into the model domain from surrounding areas. About 95 percent of the simulated groundwater discharges to steams and other surface water features, about 3 percent flows across model boundaries to surrounding areas of the groundwater system, and pumping accounts for 2 percent of discharge. Simulated flow paths are relatively local, from recharge in upland areas to discharge in nearby streams and wetlands. The model has many potential applications, including simulation of the effects of existing or proposed high-capacity wells, estimating the zone of contribution for these wells, and understanding relationships between surface water and groundwater. Future refinements to the model, such as incorporating new information about the extent and hydraulic characteristics of the Tunnel City Group, will improve its utility in understanding advective flow between the upper bedrock and Elk Mound aquifers. If seasonal or annual variations in the groundwater system are of interest, this steady-state model could be brought into a transient mode.

Wisconsin↗

Geology of the Borah Peak quadrangle, Idaho

This report is on result of a long program of geologic investigation in south-central Idaho, undertaken as an aid in the development of the mineral resources of the region. This quadrangle was examined because of the exceptional opportunities for the study of stratigraphy and structure afforded by the Lost River Range, which is the highest in Idaho and contains comparatively few intrusive igneous rocks. The Borah Peak quadrangle differs from the region to the west and northwest in that it contains parts of two sharply defined, narrow ranges elongated in a north-westerly direction, instead of broad, irregular mountain masses, in which the trends of most local topographic units are ill-defined. These ranges, the Lost River and the Lemhi, are flanked by intermontane valleys sparsely populated by stock ranchers. The Lemhi and Swauger quartzites, regarded as of Belt (pre-Cambrian) age, are named. The two Cambrian (?) formations of the Bayhorse region are not recognized in this quadrangle. The Ramshorn slate (Lower Ordovician), widespread and thick there, does not appear to be exposed anywhere in the Borah Peak quadrangle with the possible exception of small areas east of the Elkhorn Ranch, where relations are obscure. The higher Paleozoic formations, named in order of decreasing age, are the Kinnikinic quartzite, Saturday Mountain formation, Laketown dolomite, Jefferson dolomite, Grand View dolomite, Three Forks limestone, Milligen formation, Brazer limestone, and Wood River formation. The Three Forks limestone, nowhere much over 250 feet thick, is the only one of these not recognized farther west. It provides substantial aid in the interpretation of upper Paleozoic stratigraphy. Equivalent beds to the west are presumably grouped with the Milligen. The grit that introduced uncertainties into the correlation of the Wood River and Milligen formations in the southeastern part of the Bayhorse quadrangle is absent here, and both formations have close lithologic resemblances to those in the type localities in the Wood River region. Wood River strata (Pennsylvanian) crop out only in the southwest corner of the quadrangle, and the Brazer may have been the last Paleozoic unit to be deposited over most of the area. Certainly it can have had comparatively little cover over it throughout the Mesozoic. The Brazer is regarded as Mississippian, but some of the fossils in it have Pennsylvania affinities. The carbonate rocks in the Three Forks and later formations are dominantly calcareous, while those in earlier units are dolomitic. Carbonaceous matter is present in most of the formations but is abundant only in the Milligen. The Challis volcanics (Oligocene or Miocene) constitute the first stratified unit to be laid down after Paleozoic deposition ceased, although there was a little intrusive activity late in the Mesozoic. The volcanics were once widely distributed on the flanks of the mountains and are still plentiful in the northwestern corner of the quadrangle, near the head of the valley of the Pahsimeroi, and in smaller areas. They are neither so abundant nor so diversified as they are farther west. They are locally succeeded by an alluvial formation, here termed the Donkey fanglomerate, of possible Pliocene age. Abundant Quaternary glacial and alluvial deposits are present in the larger valleys. The Lemhi and Swauger quartzites were broadly folded before Paleozoic sedimentation began. Apparently the later deformation affected them only enough to render the more impure beds somewhat schistose. The Paleozoic rocks have been folded into closely spaced, asymmetric anticlines, locally broken by thrusts at and near their crests. These folds approximately parallel the trends of the present range, whereas those in the old rocks strike more nearly north. Later deformation twisted some of the folds and produced thrusts of lower dip and greater extent. The folded rocks in the Lost River Range have been arched into an anticlinorium. The original, tight folds may have preceded the emplacement of the Idaho batholith farther west, while the anticlinorium and the late twists and low thrusts result from deformation during the long period in which the batholith came to place and adjusted itself. Local intricately contorted beds in the Brazer limestone are interpreted as the effects of flowage in calcareous material subjected to tangential pressure under comparatively light supercumbent load. The quadrangle contains numerous normal faults of diverse trends. Most of those that can be conclusively demonstrated strike transverse to the trends of the ranges, but especially along parts of the southwest front of the Lemhi Range normal faults along the range fronts may have helped locally to guide erosion of the mountains. Some of the faults have displacements of thousands of feet and are thought to have originated in connection with the low-angle thrusts. Most of these, as well as minor breaks of diverse trends, affect also the Challis volcanics, which shows that renewed movement occurred in Tertiary time. The present mountain masses and broad intermontane valleys are in about the positions occupied by similar features in the early Tertiary. Several incomplete erosion cycles since then have greatly modified the topography but have not obliterated the influence of these ancient land forms. The results of early episodes in the development of the topography are much obscured by the rugged forms that result from active Pleistocene glaciation and later vigorous stream erosion, but modified remnants of the post-Challis and Donkey Hills surfaces can be clearly distinguished. Several less widespread remnants mark intermediate steps in the process. Exceptionally abundant and permeable, coarse alluvial and glacial deposits floor intermontane valleys and choke the larger mountain gorges to such an extent as to interfere with normal erosion and make the surface-water supplies even scantier than might be expected from the climate of the region, which is moderately humid in the mountains and semiarid in the valleys. Active erosion in the high mountains and comparatively static conditions on fans at the range borders result in striking contrasts.

Idaho↗

Geology and ground-water resources of the island of Oahu, Hawaii

Oahu, one of the islands of the Hawaiian group, lies in the Mid-Pacific 2,100 miles southwest of San Francisco. The principal city is Honolulu. The Koolau Range makes up the eastern part of the island, and the Waianae Range the western part. Both are extinct basaltic volcanoes deeply dissected by erosion. The Koolau Volcano was the later to become extinct. The Waianae Range is made up of three groups of lavas erupted in Tertiary and possibly in early Pleistocene time. The exposed part of the older lava is nearly 2,000 feet thick and consists largely of thin-bedded pahoehoe. It is separated in most places from the middle lavas by an angular unconformity and talus breccia and in a few places by an erosional unconformity. The middle basalts are about 2,000 feet thick and closely resemble the lower ones except that they contain more aa. The upper lavas reach a thickness of about 2,300 feet and are mostly massive aa flows. The last eruptions produced large cinder cones and some nephelite basalts. The Waianae Volcano, like other Hawaiian volcanoes, produced only small amounts of ash, and the lavas were largely extruded from fissures a few feet wide, now occupied by dikes. The center of activity was near Kolekole Pass, at the head of Lualualei Valley. The Koolau Volcano is made up of two groups of lavas extruded in Tertiary and early Pleistocene (?) time. The older group, the Kailua volcanic series, is greatly altered by hydrothermal action and was extruded from fissures near Lanikai. The flows of the younger group, the Koolau volcanic series, were extruded from fissures about a mile south of the Kailua rift and have an exposed thickness of about 3,000 feet. The Koolau Volcano produced even less ash than the Waianae Volcano, and its flows are thin-bedded pahoehoe and aa. The eruptive center of the Koolau Volcano lies between Kaneohe and Waimanalo. Great amounts of both the Waianae and Koolau Ranges were removed by fluvial and marine erosion during the Pleistocene. The master streams are characterized by deep amphitheater-headed valleys. After this erosion cycle the island was submerged more than 1,200 feet, and these great valleys were drowned and alluviated. Besides this submergence, several strand lines, preserved up to 100 feet above present sea level occur, which may be due to world-wide changes in sea level in response to the withdrawal and restoration of water concurrent with the advances and recessions of the polar ice caps and to accompanying changes in the ocean floor. During this time of shifting ocean levels spasmodic eruptions occurred on the southeast end of the Koolau Range, producing numerous lava flows and tuff cones, most of which are nephelite basalt. The last of these eruptions occurred in Recent time. A description of the climate, rates of run-off, and results of experiments to determine evaporation and transpiration in the areas of high rainfall are given. It was found that the consumptive use decreases materially and becomes a very small percentage of the rainfall in the areas of high precipitation. The lava rocks of the island are very permeable and, because of a rainfall reaching a maximum of 300 inches a year, carry large amounts of ground water, confined and unconfined, basal and perched. The basal ground water floats on salt water because of its lower specific gravity. Consequently for each foot the water table stands above sea level, salt water lies about 42 feet below sea level, in accordance with the sea along the coast as basal ground water. In most places the lava rocks along the shore are overlain by an impermeable or nearly impermeable caprock consisting of submerged lateritic soils and marine noncalcareous sediments. These deposits retard the escape of basal ground water into the sea and give rise to artesian water, but unlike most other artesian systems, this one has no lower restraining formation. The artesian water is the principal source of domestic, municipal, and irrigation supplies. The average annual quantity pumped for the period 1928 to 1933 amounted to about 105,000,000,000 gallons, nearly 90 percent of which came from Koolau hasalt and the remainder from Waianae basalt. There are ten artesian areas in the Koolau Range and two in the Waianae Range. Hydraulic gradients in these basins were found to range from 1.2 to 3 feet to the mile. Because of these extremely flat gradients and the high permeability of the aquifers it is possible to reverse the hydraulic gradients by draft and make the water flow from one artesian area to another. The artesian water levels fluctuate in response to seasonal variations in draft and recharge and in a lesser way to tidal, barometric, and seismic pressures. The water, as shown by chemical analysis, is of excellent quality except where it is contaminated with sea water. Methods have been devised for freshening wells that have gone salty, for detecting leaks, for sealing leaky and defective wells, and for recharging the artesian basins. Owing to the danger of the wells becoming brackish with increased draft, it is believed that further large developments will be more successful if shafts are sunk to sea level in the basalt as far inland as practicable, and tunnels are driven from the bottom of the shafts near the top of the saturated zone. Favorable places for such development exist in Honolulu. In addition to the basal water in the volcanic rocks, water is found in the recent gravel, beach, and dune deposits, and the emerged reef limestone. This water has been recovered by wells and tunnels, and there are favorable localities for developing additional water of this type. The island contains two types of basal springs—those like the Pearl Harbor Springs, which issue from basalt and are supplied by overflow and leakage from the artesian basin, and those which issue from the coastal-plain sediments and are mainly return irrigation water. The total quantity of basal ground water issuing as springs is estimated to be 100,000,000 gallons a day. Ground water occurs at high levels, confined by dikes and perched on tuff, alluvium, and soil beds. These structures give rise to innumerable high-level springs. In the Koolau Range 60 tunnels yield about 33,000,000 gallons daily, of which about 95 percent is obtained from tunnels penetrating the dike complex of the Koolau volcanic series, about 2 percent from tunnels entering post-Koolau ash or tuff deposits, and the remainder from tunnels whose geologic relations are not certainly known. The average daily yield of the tunnels that recover dike water is 2,330 gallons a foot, but the average daily yield of the tunnels in post-Koolau tuff is 450 gallons a foot, and that of the tunnels in alluvium or soil is only 23 gallons a foot. Owing largely to the much lower rainfall on the Waianac Range, its 35 tunnels (not including two new tunnels under construction) yield only about 2,400,000 gallons daily, about 94 percent of which is believed to be obtained from dike systems. The average daily yield of the tunnels in this range that are supplied by dike systems is 581 gallons a foot, as compared to 5 gallons a foot from tunnels in ash or tuff. An extensive tunnel system is proposed to develop a large supply of high-level water for Honolulu from the dike complex of the Koolau series, and high-level water can be recovered by tunnels at many other places. The average daily discharge of all high-level springs in the Koolau Range is about 58,000,000 gallons, of which about 94 percent comes from the Koolau dike complex and about 6 percent from post-Koolau volcanic rocks. The average daily discharge of all high-level springs in the Waianae Range is about 500,000 gallons of which about 81 percent issues from the dike complex.

Hawaii↗