Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Ground Water Modeling Investigation Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17Linked to original sources
USGS2009

Hydrology and simulation of ground-water flow in the Tooele Valley ground-water basin, Tooele County, Utah

Ground water is the sole source of drinking water within Tooele Valley. Transition from agriculture to residential land and water use necessitates additional understanding of water resources. The ground-water basin is conceptualized as a single interconnected hydrologic system consisting of the consolidated-rock mountains and adjoining unconsolidated basin-fill valleys. Within the basin fill, unconfined conditions exist along the valley margins and confined conditions exist in the central areas of the valleys. Transmissivity of the unconsolidated basin-fill aquifer ranges from 1,000 to 270,000 square feet per day. Within the consolidated rock of the mountains, ground-water flow largely is unconfined, though variability in geologic structure, stratigraphy, and lithology has created some areas where ground-water flow is confined. Hydraulic conductivity of the consolidated rock ranges from 0.003 to 100 feet per day. Ground water within the basin generally moves from the mountains toward the central and northern areas of Tooele Valley. Steep hydraulic gradients exist at Tooele Army Depot and near Erda. The estimated average annual ground-water recharge within the basin is 82,000 acre-feet per year. The primary source of recharge is precipitation in the mountains; other sources of recharge are irrigation water and streams. Recharge from precipitation was determined using the Basin Characterization Model. Estimated average annual ground-water discharge within the basin is 84,000 acre-feet per year. Discharge is to wells, springs, and drains, and by evapotranspiration. Water levels at wells within the basin indicate periods of increased recharge during 1983-84 and 1996-2000. During these periods annual precipitation at Tooele City exceeded the 1971-2000 annual average for consecutive years. The water with the lowest dissolved-solids concentrations exists in the mountain areas where most of the ground-water recharge occurs. The principal dissolved constituents are calcium and bicarbonate. Dissolved-solids concentration increases in the central and northern parts of Tooele Valley, at the distal ends of the ground-water flow paths. Increased concentration is due mainly to greater amounts of sodium and chloride. Deuterium and oxygen-18 values indicate water recharged primarily from precipitation occurs throughout the ground-water basin. Ground water with the highest percentage of recharge from irrigation exists along the eastern margin of Tooele Valley, indicating negligible recharge from the adjacent consolidated rock. Tritium and tritiogenic helium-3 concentrations indicate modern water exists along the flow paths originating in the Oquirrh Mountains between Settlement and Pass Canyons and extending between the steep hydraulic gradient areas at Tooele Army Depot and Erda. Pre-modern water exists in areas east of Erda and near Stansbury Park. Using the change in tritium along the flow paths originating in the Oquirrh Mountains, a first-order estimate of average linear ground-water velocity for the general area is roughly 2 to 5 feet per day. A numerical ground-water flow model was developed to simulate ground-water flow in the Tooele Valley ground-water basin and to test the conceptual understanding of the ground-water system. Simulating flow in consolidated rock allows recharge and withdrawal from wells in or near consolidated rock to be simulated more accurately. In general, the model accurately simulates water levels and water-level fluctuations and can be considered an adequate tool to help determine the valley-wide effects on water levels of additional ground-water withdrawal and changes in water use. The simulated increase in storage during a projection simulation using 2003 withdrawal rates and average recharge indicates that repeated years of average precipitation and recharge conditions do not completely restore the system after multiple years of below-normal precipitation. In the similar case where precipitation is 90

Utah↗
USGS2007

Modeling 3-D slope stability of coastal bluffs using 3-D ground-water flow, Southwestern Seattle, Washington

Landslides are a common problem on coastal bluffs throughout the world. Along the coastal bluffs of the Puget Sound in Seattle, Washington, landslides range from small, shallow failures to large, deep-seated landslides. Landslides of all types can pose hazards to human lives and property, but deep-seated landslides are of significant concern because their large areal extent can cause extensive property damage. Although many geomorphic processes shape the coastal bluffs of Seattle, we focus on large (greater than 3,000 m3), deepseated, rotational landslides that occur on the steep bluffs along Puget Sound. Many of these larger failures occur in advance outwash deposits of the Vashon Drift (Qva); some failures extend into the underlying Lawton Clay Member of the Vashon Drift (Qvlc). The slope stability of coastal bluffs is controlled by the interplay of three-dimensional (3-D) variations in gravitational stress, strength, and pore-water pressure. We assess 3-D slope-stability using SCOOPS (Reid and others, 2000), a computer program that allows us to search a high-resolution digital-elevation model (DEM) to quantify the relative stability of all parts of the landscape by computing the stability and volume of thousands of potential spherical failures. SCOOPS incorporates topography, 3-D strength variations, and 3-D pore pressures. Initially, we use our 3-D analysis methods to examine the effects of topography and geology by using heterogeneous material properties, as defined by stratigraphy, without pore pressures. In this scenario, the least-stable areas are located on the steepest slopes, commonly in Qva or Qvlc. However, these locations do not agree well with observations of deep-seated landslides. Historically, both shallow colluvial landslides and deep-seated landslides have been observed near the contact between Qva and Qvlc, and commonly occur in Qva. The low hydraulic conductivity of Qvlc impedes ground-water flow, resulting in elevated pore pressures at the base of Qva, thereby increasing the potential for landslides. Our analysis simulates the ground-water flow using the results of a 3-D ground-water flow model, MODFLOW-2000 (Harbaugh and others, 2000), to generate a 3-D pore-pressure field. Areas of elevated pore pressure reflect the influence of a perched ground-water table in Qva, as well as ground-water convergence in the coastal re-entrants. We obtain a realistic model of deep-seated landsliding by combining 3-D pore pressures with heterogeneous strength properties. The results show the least-stable areas where pore pressures are locally elevated in Qva. We compare our results with records of past landslides. The predicted leaststable areas include two historically active deep-seated landslides and areas adjacent to these landslides.

Scientific Investigations Report↗
USGS1982

A three-dimensional ground-water-flow model modified to reduce computer-memory requirements and better simulate confining-bed and aquifer pinchouts

The Trescott computer program for modeling groundwater flow in three dimensions has been modified to (1) treat aquifer and confining bed pinchouts more realistically and (2) reduce the computer memory requirements needed for the input data. Using the original program, simulation of aquifer systems with nonrectangular external boundaries may result in a large number of nodes that are not involved in the numerical solution of the problem, but require computer storage. (USGS)

Water-Resources Investigations Report↗
USGS2003

Analysis of tests of subsurface injection, storage, and recovery of freshwater in Lancaster, Antelope Valley, California

Ground-water levels in Lancaster, California, declined more than 200 feet during the 20th century, resulting in reduced ground-water supplies and more than 6 feet of land subsidence. Facing continuing population growth, water managers are seeking solutions to these problems. Injection of imported, treated fresh water into the aquifer system when it is most available and least expensive, for later use during high-demand periods, is being evaluated as part of a management solution. The U.S. Geological Survey, in cooperation with the Los Angeles County Department of Public Works and the Antelope Valley-East Kern Water Agency, monitored a pilot injection program, analyzed the hydraulic and subsidence-related effects of injection, and developed a simulation/optimization model to help evaluate the effectiveness of using existing and proposed wells in an injection program for halting the decline of ground-water levels and avoiding future land subsidence while meeting increasing ground-water demand. A variety of methods were used to measure aquifer-system response to injection. Water levels were measured continuously in nested (multi-depth) piezometers and monitoring wells and periodically in other wells that were within several miles of the injection site. Microgravity surveys were done to estimate changes in the elevation of the water table in the absence of wells and to estimate specific yield. Aquifer-system deformation was measured directly and continuously using a dual borehole extensometer and indirectly using continuous Global Positioning System (GPS), first-order spirit leveling, and an array of tiltmeters. The injected water and extracted water were sampled periodically and analyzed for constituents, including chloride and trihalomethanes. Measured injection rates of about 750 gallons per minute (gal/min) per well at the injection site during a 5-month period showed that injection at or above the average extraction rates at that site (about 800 gal/min) was hydraulically feasible. Analyses of these data took many forms. Coupled measurements of gravity and water-level change were used to estimate the specific yield near the injection wells, which, in turn, was used to estimate areal water-table changes from distributed measurements of gravity change. Values of the skeletal components of aquifer-system storage, which are key subsidence-related characteristics of the system, were derived from continuous measurements of water levels and aquifer-system deformation. A numerical model of ground-water flow was developed for the area surrounding Lancaster and used to estimate horizontal and vertical hydraulic conductivities. A chemical mass balance was done to estimate the recovery of injected water. The ground-water-flow model was used to project changes in ground-water levels for 10 years into the future, assuming no injection, no change in pumping distribution, and forecasted increases in ground-water demand. Simulated ground-water levels decreased throughout the Lancaster area, suggesting that land subsidence would continue as would the depletion of ground-water supplies and an associated loss of well production capacity. A simulation/optimization model was developed to help identify optimal injection and extraction rates for 16 existing and 13 proposed wells to avoid future land subsidence and to minimize loss of well production capacity while meeting increasing ground-water demands. Results of model simulations suggest that these objectives can be met with phased installation of the proposed wells during the 10-year period. Water quality was not considered in the optimization, but chemical-mass-balance results indicate that a sustained injection program likely would have residual effects on the chemistry of ground water.

Califronia↗
USGS1974

Hydrologic- and salt-balance investigations utilizing digital models Lower San Luis Rey River area, San Diego County, California

The Joint Administration Committee of the Santa Margarita and San Luis Rey Watershed Planning Agencies was designated as the agency to conduct studies leading to the development of a comprehensive water-quality management plan for the two watersheds. Hydrologic and salt balances for the Pauma, Pala, Bonsall, and Mission ground-water basins in the San Luis Rey River valley needed to develop the plan were difficult to compute because of the lack of data. Hydrologic models constructed and verified for 1958-72 for Pauma and Pala basins and for 1946-72 for Bonsall and Mission basins were beneficial in developing the hydrologic balances. Inflow and outflow to the basins used in model verification were consistent with known physical and hydrologic characteristics of the basins.

California↗
USGS1984

Streamflow augmentation at Fosters Brook, Long Island, New York — A hydraulic feasibility study

A 27-day streamflow augmentation test was conducted in December 1979 at Fosters Brook, near the south shore of Long Island, to investigate the hydraulic feasibility of pumping ground water to supply flow to an ephemeral stream during dry periods. Measurements of soil moisture in the unsaturated zone beneath the streambed indicate that infiltration rate and soil-moisture content are interrelated. Initial infiltration was measured with a neutron logger; the wetting front traversed the unsaturated zone at an average of 11.2 inches per hour and reached the water table in 5.5 hours. Soil moisture in the unsaturated zone ranged from 20 percent at the start of the test to nearly 41 percent, nearly the saturation point, 20 days later. Stream discharge was measured at four sites along the stream channel, and the augmentation rate was monitored continuously at the starting point. Infiltration rates increased steadily in all reaches during the first 12 days of the test, but from the 12th to the 20th day, when discharge was increased by 50 percent, infiltration rates decreased along the two upstream reaches but continued to increase along the three downstream reaches. Infiltration rates remained constant from days 20 through 26. During the first 24 hours of the test, the stream reached a maximum length of 2,050 feet, but after 13 days, it had shortened to 1,300 feet as a result of seepage losses. The relationship between discharge and stream length was linear within the range of discharge investigated (0.54-1.63 cubic feet per second). Ground-water levels rose in response to flow augmentation and reached a maximum rise of about 6.5 feet in a well situated 14 feet from the center of the streambed and 225 feet downstream from the start of the flow. Measured water-level response was compared to levels predicted by a one-dimensional analytical model and a three-dimensional mathematical model; results indicate that ground-water response is determined principally by streambed characteristics and soil-moisture content in the unsaturated zone. Variations in water temperature and in streambed composition had significant effects upon infiltration rates. Changes in water temperature, amount of vegetation, soil-moisture content, and stream stage, combined with local variations in streambed permeability and aquifer conductivity, make accurate prediction of seepage rates virtually impossible at present. Data from this study suggest that site-specific investigations are necessary wherever streamflow augmentation is planned.

New York↗
USGS2004

Hydrogeologic characterization of the Modesto Area, San Joaquin Valley, California

Hydrogeologic characterization was done to develop an understanding of the hydrogeologic setting near Modesto by maximizing the use of existing data and building on previous work in the region. A substantial amount of new lithologic and hydrologic data are available that allow a more complete and updated characterization of the aquifer system. In this report, geologic units are described, a database of well characteristics and lithology is developed and used to update the regional stratigraphy, a water budget is estimated for water year 2000, a three-dimensional spatial correlation map of aquifer texture is created, and recommendations for future data collection are summarized. The general physiography of the study area is reflected in the soils. The oldest soils, which have low permeability, exist in terrace deposits, in the interfan areas between the Stanislaus, Tuolumne, and Merced Rivers, at the distal end of the fans, and along the San Joaquin River floodplain. The youngest soils have high permeability and generally have been forming on the recently deposited alluvium along the major stream channels. Geologic materials exposed or penetrated by wells in the Modesto area range from pre-Cretaceous rocks to recent alluvium; however, water-bearing materials are mostly Late Tertiary and Quaternary in age. A database containing information from more than 3,500 drillers'logs was constructed to organize information on well characteristics and subsurface lithology in the study area. The database was used in conjunction with a limited number of geophysical logs and county soil maps to define the stratigraphic framework of the study area. Sequences of red paleosols were identified in the database and used as stratigraphic boundaries. Associated with these paleosols are very coarse grained incised valley-fill deposits. Some geophysical well logs and other sparse well information suggest the presence of one of these incised valley-fill deposits along and adjacent to the Tuolumne River east of Modesto, a feature that may have important implications for ground-water flow and transport in the region. Although extensive work has been done by earlier investigators to define the structure of the Modesto area aquifer system, this report has resulted in some modification to the lateral extent of the Corcoran Clay and the regional dip of the Mehrten Formation. Well logs in the database indicating the presence of the Corcoran Clay were used to revise the eastern extent of the Corcoran Clay, which lies approximately parallel to the axis of valley. The Mehrten Formation is distinguished in the well-log database by its characteristic black sands consisting of predominantly andesitic fragments. Black sands in wells listed in the database indicate that the formation may lie as shallow as 120 meters (400 feet) below land surface under Modesto, approximately 90 meters (300 feet) shallower than previously thought. The alluvial aquifer system in the Modesto area comprises an unconfined to semiconfined aquifer above and east of the Corcoran Clay confining unit and a confined aquifer beneath the Corcoran Clay. The unconfined aquifer is composed of alluvial sediments of the Modesto, Riverbank, and upper Turlock Lake formations. The unconfined aquifer east of the Corcoran Clay becomes semiconfined with depth due to the numerous discontinuous clay lenses and extensive paleosols throughout the aquifer thickness. The confined aquifer is composed primarily of alluvial sediments of the Turlock Lake and upper Mehrten Formations, extending from beneath the Corcoran Clay to the base of fresh water. Ground water in the unconfined to semiconfined aquifer flows to the west and southwest. The primary source of present-day recharge is percolating excess irrigation water. The primary ground-water discharge is extensive ground-water pumping in the unconfined to semiconfined aquifer, imposing a significant component of vertical flow in the system. A water budget was calculated for water year 2000 using a land-use approach. During water year 2000, the total water supply in the Modesto area was more than 2.5 billion m3 (cubic meter) (2 million acre-ft [acre-foot]). Surface-water deliveries accounted for 60 percent of the total water supply, whereas ground-water pumpage accounted for 40 percent. Ninety-four percent of the water supply was used to meet irrigation demand and approximately 6 percent was used to meet urban demand. The total recharge in the model area was estimated at 1.4 billion m3 (1,100,000 acre-ft). The largest component of recharge is from excess irrigation water (58 percent); precipitation in excess of crop requirements accounted for 41 percent of the recharge. Geostatistical methods were used to develop a spatial correlation model of the percentage of coarse-grained texture in the Modesto area. The mean percentage coarse-grained texture calculated for each depth increment indicates a regional trend of decreasing coarse-grained texture with increasing depth, which is consistent with increasingly consolidated sediments with depth in the study area. The three-dimensional kriged estimates of percentage coarse-grained texture show significant heterogeneity in the texture of the sedimentary deposits. Assuming the hydraulic conductivity is correlated to the texture, the kriged result implies significant heterogeneity in the hydrogeologic framework.

California↗
USGS1995

Simulated ground-water flow and sources of water in the Killbuck Creek Valley near Wooster, Wayne County, Ohio

The stratified-drift aquifer in the 3,000-ft (feet)-wide and 100-ft-deep buried valley of Killbuck Creek near Wooster in northeastern Ohio was studied. The stratified drift with adjacent sandstone and shale bedrock produce a system of ground-water flow representative of the western part of the glaciated north-eastern United States. The stratified-drift aquifer is an excellent source of water for municipal and industrial wells. The aquifer is recharged locally by water from precipitation on the valley floor and uplands, by infiltration from streams, and by lateral flow to the valley from the uplands. As a result, the aquifer is vulnerable to surface or subsurface spills of contaminants in the valley or the adjacent uplands. Quality of water in the stratified drift is affected by influx of water from bedrock lateral to or beneath the valley. This influx is controlled, in part, by the pumping stress placed on the stratified-drift aquifer. Hydrogeologic and aqueous-geochemical data were analyzed to establish the framework necessary for stead-state and transient simulations of ground-water flow in stratified drift and bedrock with a three-layer ground-water-flow model. A new model routine, the Variable-Recharge procedure, was developed to simulate areal recharge and the contribution of the uplands to the drift system. This procedure allows for water applied to land surface to infiltrate or to be rejected. Rejected recharge and ground water discharged when the water table is at land surface form surface runoff-this excess upland water can be redirected as runoff to other parts of the model. Infiltration of streamwater, areal recharge to uplands and valley, and lateral subsurface flow from the uplands to the valley are sources of water to the stratufued0druft aquifer. Water is removed from the stratified-drift aquifer at Wooster primarily by production wells pumping at a rate of approximately 8.5 ft3/s (cubic feet per second). The ground-water budget resulting from two types of simulations of ground-water flow in this study indicates the primary sources of water to the wells are recharge at or near land surface and lateral subsurface flow from the shale and sandstone bedrock. Components of recharge at land surface include induced infiltration from streams, precipitation on the valley floor, and infiltration of unchanneled upland runoff that reaches the valley floor. The steady-state simulation was designed to represent conditions during the fall of 1984. The transient simulation was designed to represent an 11-day snowmelt event, 23 February to 5 March 1985, that caused water levels to rise significantly throughout the valley. Areal recharge to the valley and flow from the uplands to the valley were determined through the Variable-Recharge procedure. The total steady-state recharge to the valley was 12.5 ft3/s. Upland sources, areal valley recharge, and induced infiltration from Killnuck Creek accounted for 63, 23, and 8 percent, respectively, of the valley recharge. An analysis of the simulated vertical flow to the buried stratified drift through surficial slit, clay, and fine sand indicates that about 75 percent of the total recharge to the buried deposits is the sum of areally extensive, relatively small flows less than about 0.01 ft? /s per model node), whereas about 25 percent of the recharge results from a really restricted, relatively large flows (greater than about 0.01 ft? /s per model node). The large-magnitude flows are located primarily beneath Clear and Little Killbuck Creeks where seepage provides abundant recharge and the surficial sediments grade into coarser alluvial-fan deposits. Chemical and isotopic studies of ground water and streamwater combined with measurements of stream infiltration provide independent support for the conclusions derived from computer simulation of ground-water flow. In addition, the chemical and isotopic studies helped quantity the rate and pathways of infiltrating water from

Water-Resources Investigations Report↗
USGS1985

Gravity survey and depth to bedrock in Carson Valley, Nevada-California

Gravity data were obtained from 460 stations in Carson Valley, Nevada and California. The data have been interpreted to obtain a map of approximate depth to bedrock for use in a ground-water model of the valley. This map delineates the shape of the alluvium-filled basin and shows that the maximum depth to bedrock exceeds 5,000 feet, on the west side of the valley. A north-south trending offset in the bedrock surface shows that the Carson-Valley/Pine-Nut-Mountain block has not been tilted to the west as a simple unit, but is comprised of several smaller blocks.

California, Nevada↗
USGS1974

Hydrologic analysis of the Mojave River, California, using a mathematical model

The channel of the Mojave Rive'r in California is normally dry and is highly permeable over much of its length, and large quantities of water from natural floodflows in the channel infiltrate through the channel bed to the underlying ground-water body. From 1930 to 1972 only 18 floods at The Forks produced flow at Barstow, 55 miles (88 kilometres) downstream from The Forks. Peak discharges at Barstow from these floods ranged from 180 cubic feet per second (5 cubic metres per second) in 1967 to 64,300 cubic feet per second (1,820 cubic metres per second) in 1938. Total stream infiltration, primarily as ground-water recharge, ranged from 3,600 acre-feet (4.40 cubic hectometres) in 1935 to 50,400 acre-feet (62.1 cubic hectometres) in 1969 between The Forks and Victorville and from about 7,000 acre-feet (8.61 cubic hectometres) in 1935 to 128,000 acre-feet (158 cubic hectometres) in 1969 between Victorville and Barstow. The Mojave Water Agency is considering the use of the channel of the river to convey water imported from northern California through Silverwood Reservoir (5 miles or 8 kilometres upstream from The Forks) downstream to the Barstow area. The imported water would be used to replenish aquifers underlying the Barstow area. A mathematical model was developed that simulates the advance of discharge down the initially dry channel of the Mojave River, and the model was used to evaluate the potential of the channel to move imported water downstream to Barstow. Results of simulation by modeling indicate that the channel of the Mojave River can be used to efficiently convey imported water to Barstow only when the absorption capacity of the channel has been reduced by an antecedent flood. The volume of imported water that can reach Barstow depends on the volume and duration of the antecedent flood, on the volume of imported water released trom Silverwood Reservoir, and on the rate at which imported water is released. A release of 20,000 acre-feet (24.6 cubic hectometres) of imported water may produce at Barstow a maximum volume of imported water of 2,500, 8,000, 11,000, or 15,000 acre-feet (3.08, 9.86, 13.6, or 18.4 cubic hectometres) for a release rate of 500, 750, 1,000, or 2,000 cubic feet per second (14.2, 21.2, 28.3, or 56.8 cubic metres per second). For planning purposes in evaluating some of the hydraulic effects of recharge on the aquifer, a simulation of the aquifer near the Barstow area using an electrical analog model showed that a combination of no pumping and a yearly recharge of 5,000 acre-feet (6.17 cubic hectometres) for 10 years could raise ground-water levels at least 10 feet (3 metres) over an area of about 10 square miles (25 square kilometres). To obtain the water-level changes due to the combined effects of pumping and recharge, the above water-level changes should be superimposed on the separate effects of pumping.

California↗
USGS1999

Hydrogeology and simulation of ground-water flow in the Ohio River alluvial aquifer near Carrollton, Kentucky

The alluvial aquifer near Carrollton, Kentucky, lies in a valley eroded by glacial meltwater that was later part filled with outwash sand and gravel deposits. The aquifer is unconfined, and ground water flows from the adjacent bedrock-valley wall toward the Ohio River and ground-water withdrawal wells. Ground-water-level and Ohio River stage data indicate the alluvial aquifer was at or near steady-state condition in November 1995. A two-dimensional, steady-state ground-water-flow model was developed to estimate the hydraulic properties, the rate of recharge, and the contributing areas to discharge boundaries for the Ohio River alluvial aquifer at Carrollton and the surrounding area. Results from previous investigations, available hydrogeologic data, and observations of water levels from area ground-water wells were compiled to conceptualize the ground-water-flow system and construct the numerical model. Ground water enters the modeled area by induced infiltration from the Ohio River and smaller streams, flow from the bedrock-valley wall, and infiltration of precipitation. Ground water exits the modeled area primarily through withdrawal wells and flow to the Ohio River. A sensitivity analysis of the model indicates that it is most sensitive to changes in the stage of the Ohio River and conductance values for the riverbed material. A particle-tracking simulation was used to delineate recharge and discharge boundaries of the flow system and contributing areas for withdrawal wells, and to estimate time of travel through the flow system.

Water-Resources Investigations Report↗
USGS1994

Geohydrology and water quality of stratified-drift aquifers in the lower Connecticut River basin, southwestern New Hampshire

Stratified-drift aquifers discontinuously underlie 116 square miles of the Lower Connecticut River basin in southwestern New Hampshire, which has a total drainage area of 1,163 square miles. Saturated thicknesses of stratified drift within the study area are locally greater than 400 feet but generally are less. Transmissivities 1ocally exceeds 4,000 feet squared per day but are generally much less. The 20.8 square mile, or 1.8 percent, of the study area identified as having transmissivity greater than 1,000 feet squared per day represents a valuable resource. The geohydrology of stratified- drift aquifers was investigated by focusing on basic aquifer properties, including aquifer boundaries; recharge, discharge, and direction of ground-water flow; saturated thickness and storage; and transmissivity. Surficial geologic mapping assisted in the determination of aquifer boundaries. Data from more than 2,300 wells, test borings, and springs were used to produce maps of water-table altitude, saturated thickness, and transmissivity of-stratified drift. Seismic-refraction profiles were completed at 29 locations in the study area. These profiles aided in the construction of the water-table and saturated-thickness maps. Seismic- reflection data were also collected along 60 miles of the Connecticut River. A stratified-drift aquifer in southern Croydon and northern Newport was analyzed for aquifer yield using transient simulations and a two-dimensional, finite-difference ground-water-flow model. The objective was to estimate the yield after a 180-day period of pumping. Two hypothetical wells were pumped at 1.0 Mgal/d and 0.5 Mgal/d for 180 days respectively. The amount of water available for infiltration was the limiting factor. Results of analysis of water samples from 22 wells and 8 spring show that, with some exceptions, water in the stratified-drift aquifer generally meets the U.S. Environmental Protection Agency's primary and secondary drinking-water regulations.

Water-Resources Investigations Report↗
USGS1998

Hydrogeology and simulation of ground-water flow in the Sandstone Aquifer, northeastern Wisconsin

Municipalities in the lower Fox River Valley in northeastern Wisconsin obtain their water supply from a series of permeable sandstones and carbonates of Cambrian to Ordovician age. Withdrawals from this "sandstone aquifer" have resulted in water levels declining at a rate of more than 2 feet per year. The U.S. Geological Survey, in cooperation with the major water utilities in the Fox Cities area, the East Central Wisconsin Regional Planning Commission and the Wisconsin Geological and Natural History Survey, collected hydrogeological data and constructed a quasithree- dimensional, transient ground-water-flow model for use as a tool in assessing the water resources of the sandstone aquifer. The rocks of the Sinnipee Group and Maquoketa Shale form the Maquoketa-Sinnipee confining unit that separates the sandstone aquifer from the overlying upper aquifer, which consists of unconsolidated deposits and permeable dolomite of Silurian age. The confining unit is present in the eastern part of the study area, but is absent in the western part, where the upper aquifer directly overlies the sandstone aquifer. The ground-water-flow model simulates water levels in the two aquifers and vertical flow across the confining unit. Streams and lakes are simulated in the upper aquifer as head-dependent boundaries where the confining unit is absent and as constant head boundaries where the confining unit is present. The sandstone aquifer has constant heads assigned to the southern boundary, which is far from the lower Fox River Valley and coincident with a ground-water divide. The model was calibrated to predevelopment, 1957, and 1990 water levels, and used to simulate steady-state predevelopment conditions and transient conditions from 1880 to 1990. The trend in simulated water levels over time was similar to trends in measured water levels. Simulated base flow to streams was within the calculated range of base flow at gaged streams. A groundwater divide that separates westerly ground-water flow to the Wolf River from easterly flow to the lower Fox River Valley and Lake Michigan was simulated.

Wisconsin↗
USGS2007

Ground-Water Flow Model for the Spokane Valley-Rathdrum Prairie Aquifer, Spokane County, Washington, and Bonner and Kootenai Counties, Idaho

This report presents a computer model of ground-water flow in the Spokane Valley-Rathdrum Prairie (SVRP) aquifer in Spokane County, Washington, and Bonner and Kootenai Counties, Idaho. The aquifer is the sole source of drinking water for more than 500,000 residents in the area. In response to the concerns about the impacts of increased ground-water withdrawals resulting from recent and projected urban growth, a comprehensive study was initiated by the Idaho Department of Water Resources, the Washington Department of Ecology, and the U.S. Geological Survey to improve the understanding of ground-water flow in the aquifer and of the interaction between ground water and surface water. The ground-water flow model presented in this report is one component of this comprehensive study. The primary purpose of the model is to serve as a tool for analyzing aquifer inflows and outflows, simulating the effects of future changes in ground-water withdrawals from the aquifer, and evaluating aquifer management strategies. The scale of the model and the level of detail are intended for analysis of aquifer-wide water-supply issues. The SVRP aquifer model was developed by the Modeling Team formed within the comprehensive study. The Modeling Team consisted of staff and personnel working under contract with the Idaho Department of Water Resources, personnel working under contract with the Washington Department of Ecology, and staff of the U.S. Geological Survey. To arrive at a final model that has the endorsement of all team members, decisions on modeling approach, methodology, assumptions, and interpretations were reached by consensus. The ground-water flow model MODFLOW-2000 was used to simulate ground-water flow in the SVPR aquifer. The finite-difference model grid consists of 172 rows, 256 columns, and 3 layers. Ground-water flow was simulated from September 1990 through September 2005 using 181 stress periods of 1 month each. The areal extent of the model encompasses an area of approximately 326 square miles. For the most part, the model extent coincides with the 2005 revised extent of the Spokane Valley-Rathdrum Prairie aquifer as defined in a previous report. However, the model excludes Spirit and Hoodoo Valleys because of uncertainties about the ground-water flow directions in those valleys and the degree of hydraulic connection between the valleys and northern Rathdrum Prairie. The SVRP aquifer is considered to be a single hydrogeologic unit except in Hillyard Trough and the Little Spokane River Arm. In those areas, a continuous clay layer divides the aquifer into an upper, unconfined unit and a lower, confined unit. The model includes all known components of inflows to and outflows from the aquifer. Inflows to the SVRP aquifer include (1) recharge from precipitation, (2) inflows from tributary basins and adjacent uplands, (3) subsurface seepage and surface overflows from lakes that border the aquifer, (4) flow from losing segments of the Spokane River to the aquifer, (5) return percolation from irrigation, and (6) effluent from septic systems. Outflows from the SVRP aquifer include (1) ground-water withdrawals from wells, (2) flow from the aquifer to gaining segments of the Spokane River, (3) aquifer discharge to the Little Spokane River, and (4) subsurface outflow from the lower unit at the western limit of the model area near Long Lake. These inflow and outflow components are represented in the model by using MODFLOW-2000 packages. The parameter-estimation program PEST was used to calibrate the SVRP aquifer model. PEST implements a nonlinear least-squares regression method to estimate model parameters so that the differences between measured and simulated quantities are minimized with respect to an optimal criterion. Calibration data include 1,573 measurements of water levels and 313 measurements of streamflow gains and losses along segments of the Spokane and Little Spokane Rivers. Model parameters estimated during calib

Scientific Investigations Report↗
USGS2006

Geohydrological characterization, water-chemistry, and ground-water flow simulation model of the Sonoma Valley area, Sonoma County, California

The Sonoma Valley, located about 30 miles north of San Francisco, is one of several basins in Sonoma County that use a combination of ground water and water delivered from the Russian River for supply. Over the past 30 years, Sonoma Valley has experienced rapid population growth and land-use changes. In particular, there has been a significant increase in irrigated agriculture, predominantly vineyards. To provide a better understanding of the ground-water/surface-water system in Sonoma Valley, the U.S. Geological Survey compiled and evaluated existing data, collected and analyzed new data, and developed a ground-water flow model to better understand and manage the ground-water system. The new data collected include subsurface lithology, gravity measurements, groundwater levels, streamflow gains and losses, temperature, water chemistry, and stable isotopes. Sonoma Valley is drained by Sonoma Creek, which discharges into San Pablo Bay. The long-term average annual volume of precipitation in the watershed is estimated to be 269,000 acre-feet. Recharge to the ground-water system is primarily from direct precipitation and Sonoma Creek. Discharge from the ground-water system is predominantly outflow to Sonoma Creek, pumpage, and outflow to marshlands and to San Pablo Bay. Geologic units of most importance for groundwater supply are the Quaternary alluvial deposits, the Glen Ellen Formation, the Huichica Formation, and the Sonoma Volcanics. In this report, the ground-water system is divided into three depth-based geohydrologic units: upper (less than 200 feet below land surface), middle (between 200 and 500 feet), and lower (greater than 500 feet). Synoptic streamflow measurements were made along Sonoma Creek and indicate those reaches with statistically significant gains or losses. Changes in ground-water levels in wells were analyzed by comparing historical contour maps with the contour map for 2003. In addition, individual hydrographs were evaluated to assess temporal changes by region. In recent years, pumping depressions have developed southeast of Sonoma and southwest of El Verano. Water-chemistry data for samples collected from 75 wells during 2002-04 indicate that the ground-water quality in the study area generally is acceptable for potable use. The water from some wells, however, contains one or more constituents in excess of the recommended standards for drinking water. The chemical composition of water from creeks, springs, and wells sampled for major ions plot within three groups on a trilinear diagram: mixed-bicarbonate, sodium-mixed anion, and sodium-bicarbonate. An area of saline ground water in the southern part of the Sonoma Valley appears to have shifted since the late 1940s and early 1950s, expanding in one area, but receding in another. Sparse temperature data from wells southwest of the known occurrence of thermal water suggest that thermal water may be present beneath a larger part of the valley than previously thought. Thermal water contains higher concentrations of dissolved minerals than nonthermal waters because mineral solubilities generally increase with temperature. Geohydrologic Characterization, Water-Chemistry, and Ground-Water Flow Simulation Model of the Sonoma Valley Area, Sonoma County, California Oxygen-18 (d18 O) and deuterium (dD) values for water from most wells plot along the global meteoric water line, indicating that recharge primarily is derived from the direct infiltration of precipitation or the infiltration of seepage from creeks. Samples from shallow- and intermediate-depth wells located near Sonoma Creek and (or) in the vicinity of Shellville plot to the right of the global meteoric water line, indicating that these waters are partly evaporated. The d18 O and dD composition of water from sampled wells indicates that water from wells deeper than 200 feet is isotopically lighter (more negative) than water from wells less than 200 feet deep, possibly indicating that older ground wate

California↗
USGS1996

Hydrogeology of, and simulation of ground-water flow in, a mantled carbonate-rock system, Cumberland Valley, Pennsylvania

The U.S. Geological Survey conducted a study in a highly productive and complex regolith-mantled carbonate valley in the northeastern part of the Cumberland Valley, Pa., as part of its Appalachian Valleys and Piedmont Regional Aquifer-system Analysis program. The study was designed to quantify the hydrogeologic characteristics and understand the ground-water flow system of a highly productive and complex thickly mantled carbonate valley. The Cumberland Valley is characterized by complexly folded and faulted carbonate bedrock in the valley bottom, by shale and graywacke to the north, and by red-sedimentary and diabase rocks in the east-southeast. Near the southern valley hillslope, the carbonate rock is overlain by wedge-shaped deposit of regolith, up to 450 feet thick, that is composed of residual material, alluvium, and colluvium. Locally, saturated regolith is greater than 200 feet thick. Seepage-run data indicate that stream reaches, near valley walls, are losing water from the stream, through the regolith, to the ground-water system. Results of hydrograph-separation analyses indicate that base flow in stream basins dominated by regolith-mantled carbonate rock, carbonate rock, and carbonate rock and shale are 81.6, 93.0, and 67.7 percent of total streamflow, respectively. The relative high percentage for the regolith-mantled carbonate-rock basin indicates that the regolith stores precipitation and slowly, steadily releases this water to the carbonate-rock aquifer and to streams as base flow. Anomalies in water-table gradients and configuration are a result of topography and differences in the character and distribution of overburden material, permeability, rock type, and geologic structure. Most ground-water flow is local, and ground water discharges to nearby springs and streams. Regional flow is northeastward to the Susquehanna River. Average-annual water budgets were calculated for the period of record from two continuous streamflow-gaging stations. Average-annual precipitation range from 39.0 to 40.5 inches, and averages about 40 inches for the model area. Average-annual recharge, which was assumed equal to the average-annual base flow, ranged from 12 inches for the Conodoguinet Creek, and 15 inches for the Yellow Breeches Creek. The thickly-mantled carbonate system was modeled as a three- dimensional water-table aquifer. Recharge to, ground-water flow through, and discharge from the Cumberland Valley were simulated. The model was calibrated for steady-state conditions using average recharge and discharge data. Aquifer horizontal hydraulic conductivity was calculated from specific-capacity data for each geologic unit in the area. Particle-tracking analyses indicate that interbasin and intrabasin flows of groundwater occur within the Yellow Breeches Creek Basin and between the Yellow Breeches and Conodoguinet Creek Basins.

Pennsylvania↗
USGS1995

Estimates of ground-water recharge rates for two small basins in central Nevada

Estimates of ground-water recharge rates developed from hydrologic modeling studies are presented for 3-Springs and East Stewart basins. two small basins (analog sites) located in central Nevada. The analog-site studies were conducted to aid in the estimation of recharge to the paleohydrologic regime associated with ground water in the vicinity of Yucca Mountain under wetter climatic conditions. The two analog sites are located to the north and at higher elevations than Yucca Mountain, and the prevailing (current) climatic conditions at these sites is thought to be representative of the possible range of paleoclimatic conditions in the general area of Yucca Mountain during the Quaternary. Two independent modeling approaches were conducted at each of the analog sites using observed hydrologic data on precipitation, temperature, solar radiation stream discharge, and chloride-ion water chemistry for a 6-year study period (October 1986 through September 1992). Both models quantify the hydrologic water-balance equation and yield estimates of ground-water recharge, given appropriate input data. The first model uses a traditional approach to quantify watershed hydrology through a precipitation-runoff modeling system that accounts for the spatial variability of hydrologic inputs, processes, and responses (outputs) using a dailycomputational time step. The second model is based on the conservative nature of the dissolved chloride ion in selected hydrologic environments, and its use as a natural tracer allows the computation of acoupled, water and chloride-ion, mass-balance system of equations to estimate available water (sum ofsurface runoff and groundwater recharge). Results of the modeling approaches support the conclusion that reasonable estimates of average-annual recharge to ground water range from about 1 to 3 centimeters per year for 3-Springs basin (the drier site), and from about 30 to 32 centimeters per year for East Stewart basin (the wetter site). The most reliable results are those derived from a reduced form of the chloride-ion model because they reflect integrated, basinwide processes in terms of only three measured variables: precipitation amount, precipitation chemistry, and streamflow chemistry.

Nevada↗
USGS2006

Composition of Titan's surface from Cassini VIMS

Titan's bulk density along with Solar System formation models indicates considerable water as well as silicates as its major constituents. This satellite's dense atmosphere of nitrogen with methane is unique. Deposits or even oceans of organic compounds have been suggested to exist on Titan's solid surface due to UV-induced photochemistry in the atmosphere. Thus, the composition of the surface is a major piece of evidence needed to determine Titan's history. However, studies of the surface are hindered by the thick, absorbing, hazy and in some places cloudy atmosphere. Ground-based telescope investigations of the integral disk of Titan attempted to observe the surface albedo in spectral windows between methane absorptions by calculating and removing the haze effects. Their results were reported to be consistent with water ice on the surface that is contaminated with a small amount of dark material, perhaps organic material like tholin. We analyze here the recent Cassini Mission's visual and infrared mapping spectrometer (VIMS) observations that resolve regions on Titan. VIMS is able to see surface features and shows that there are spectral and therefore likely compositional units. By several methods, spectral albedo estimates within methane absorption windows between 0.75 and 5 ??m were obtained for different surface units using VIMS image cubes from the Cassini-Huygens Titan Ta encounter. Of the spots studied, there appears to be two compositional classes present that are associated with the lower albedo and the higher albedo materials, with some variety among the brighter regions. These were compared with spectra of several different candidate materials. Our results show that the spectrum of water ice contaminated with a darker material matches the reflectance of the lower albedo Titan regions if the spectral slope from 2.71 to 2.79 ??m in the poorly understood 2.8-??m methane window is ignored. The spectra for brighter regions are not matched by the spectrum of water ice or unoxidized tholin, in pure form or in mixtures with sufficient ice or tholin present to allow the water ice or tholin spectral features to be discerned. We find that the 2.8-??m methane absorption window is complex and seems to consist of two weak subwindows at 2.7 and 2.8 ??m that have unknown opacities. A ratio image at these two wavelengths reveals an anomalous region on Titan that has a reflectance unlike any material so far identified, but it is unclear how much the reflectances in these two subwindows pertain to the surface. ?? 2006 Elsevier Ltd. All rights reserved.

Planetary and Space Science↗