Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Climate of the Past”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,687 records · Page 17Linked to original sources
USGS2024

Monitoring marine eruptions

Introduction Submarine volcanoes produce much of the same seismicity and eruptive activity as subaerial volcanoes and can pose hazards to society. Although they can be monitored with similar techniques and methods as described in other chapters of this volume, their submerged location brings unique challenges. This chapter addresses these challenges and provides recommendations for monitoring volcanoes fully or partly in marine environments to meet the capabilities described in other chapters of this volume. The United States and its territories host dozens of submarine volcanoes with most (around 60) in the Commonwealth of the Northern Mariana Islands. Approximately 20 of the Northern Mariana Islands submarine volcanoes are known to be hydrothermally active, and 10 have confirmed eruptions since the 1950s (for example, Baker and others, 2008; Tepp and others, 2019a). Nine of those volcanoes were considered by the National Volcanic Threat Assessment (Ewert and others, 2018) to have a combination of eruptive type and summit depth that poses a higher risk of hazardous eruptions, although only one was listed as a moderate (level 3) threat. Other notable submarine volcanoes of interest to the United States that have historically erupted are Axial Seamount off the Washington State coast, Kamaʻehuakanaloa in Hawaiʻi, and Vailuluʻu seamount in American Samoa. All of these, however, have a low risk of hazards because of their depth (greater than 600 meters below sea level) and eruptive type and so are not included in the National Volcanic Threat Assessment. In addition to submarine volcanoes, the submerged flanks of island volcanoes can also be a source of hazardous submarine eruptions—for example, the 1877 eruption of Mauna Loa, Hawai‘i, in Kealakekua Bay (Wanless and others, 2006). The most notable submarine eruption in recent times was the 2022 eruption of Hunga Tonga–Hunga Haʻapai in Tonga, which was one of the largest eruptions on Earth in the past 100 years. It created a massive volcanic plume, unprecedented shock waves, and far-reaching tsunami (Lynett and others, 2022). Other recent submarine eruptions in the Pacific Ocean Basin have produced subaerial plumes that reached aircraft heights (Carey and others, 2014) and large pumice rafts that can affect marine traffic and harbors (for example, Jutzeler and others, 2014; Kornei, 2019). These examples illustrate the potential hazards of major submarine eruptions. Yet, submarine volcanoes are largely unmonitored, and many eruptions occur that are unnoticed or only identified hours or days afterward. Within U.S. territory, submarine volcanoes in the Northern Mariana Islands have been known to produce eruptive activity that can affect society. Reports from fishermen and other marine vessels in the Northern Mariana Islands have noted underwater explosions, sea-surface discoloration, and bubbling water, all of which are known to be signs of submarine volcanic activity. South Sarigan seamount, located about 160 kilometers (km) north of Saipan, erupted in 2010 from greater than 150 meters below the sea surface, resulting in a gas and ash plume that reached more than 11.9 km into the atmosphere (for example, Searcy, 2013; Embley and others, 2014), high enough to affect international air traffic. Precursory and co-eruptive seismicity was detected on the regional Northern Mariana Islands seismic network (Searcy, 2013) and on global monitoring instruments (Green and others, 2013). Monitoring of submarine volcanoes is best accomplished with marine-based instrumentation, which is also useful for monitoring small island volcanoes that may not have the land area necessary for comprehensive subaerial monitoring. The primary marine-based instrumentation used for submarine volcanoes includes ocean-bottom pressure sensors to assess sea-floor deformation, ocean-bottom seismometers (OBSs) to detect seismicity, and both moored and ocean-bottom hydrophones to detect submarine explosions. Other sensors offer important monitoring data, such as turbidity, temperature, and chemistry of hydrothermal emissions. Marine-based instruments are typically deployed in campaign-style networks with no real-time telemetry owing to cost considerations and technical limitations. However, when necessary, marine instruments can be operated in real time using cables to transmit data to land-based facilities; other technologies for this purpose are in use or in development, such as acoustic transmission from the instrument to a moored buoy (Matsumoto and others, 2016) and a winch-based system with a satellite antenna that is part of the instrument mooring (Matsumoto and others, 2019). Emerging technologies for marine-based monitoring may be considered as part of a future monitoring plan. These technologies include ocean gliders and floats with on-board hydrophones that have been used to record earthquakes and submarine eruptions (for example, Matsumoto and others, 2013; Sukhovich and others, 2015) and fiber-optic cables that have been used as strainmeters to detect earthquakes (for example, Marra and others, 2018; Lindsey and others, 2019). Land-based instruments and satellites can also provide some capability for monitoring submarine volcanoes, but they provide more limited observations than marine-based instrumentation.

Scientific Investigations Report↗
USGS2024

Post-wildfire debris flows

Post-wildfire debris flows pose severe hazards to communities and infrastructure near and within recently burned mountainous terrain. Intense heat of wildfires changes the runoff characteristics of a watershed by combusting the vegetative canopy, litter, and duff, introducing ash into the soil and creating water repellant soils. Following wildfire, rainfall on bare ground is less able to infiltrate into the fire-altered soils and overland flow is less impeded by vegetation. Rainfall runoff in recently burned areas can erode hillslopes owing to the removal of soil binding organic matter near the soil surface by fire. In channels, loose, dry-ravel deposits composed of sand and gravel are readily entrained by concentrated runoff in channels. Entrainment of soil on hillslopes and in channels bulks up the sediment concentration of the rainfall runoff to generate debris flows capable of transporting boulders and large woody debris. Post-wildfire debris flows can be triggered by rainfall conditions that would typically produce little runoff during unburned conditions. The primary rainfall trigger for post-wildfire debris flows is high intensity rainfall during short duration convective rainstorms or periods of high rainfall intensity embedded within a long-duration frontal storm. Numerous observations of debris flows triggered by storms lasting less than an hour following periods of little to no rainfall indicate that antecedent rainfall is not a requirement for initiation of post-wildfire debris flows. Post-wildfire debris-flow hazard assessment entails estimating probability and magnitude of debris flows in the burned area, estimating debris-flow runout and intensity, and defining rainfall intensity-duration thresholds for debris-flow initiation. In the United States, probability and magnitude is estimated using empirically derived models largely based on data collected in southern California. The models provide maps to identify watersheds and drainage paths where post-wildfire hazards are most pronounced. Rainfall intensity-duration thresholds can be incorporated into flood hazard forecasting tools. Currently, work is underway to identify how to best implement debris-flow runout models in burned areas with efficiency and accuracy. Post-wildfire debris flows have been a long-recognized process in the Transverse Ranges of southern California; however, climate change is driving more frequent wildfires to burn more mountainous terrain throughout the western United States and worldwide. As a result, post-wildfire debris flows are becoming a more common threat in areas where they were once infrequent. As the threat of post-wildfire debris flow expands into new areas, evaluating the hazard becomes challenging because the degree to which wildfire increases debris-flow susceptibility varies from region to region. This chapter summarizes the knowledge to date for evaluating post-wildfire debris-flow susceptibility and hazard assessment. We summarize the characteristics of wildfire burn severity, topography, underlying soil and geology, and rainfall conditions that contribute to making a watershed most likely to produce post-wildfire debris flows. Methods for hazard assessment in the United States and other countries are summarized. We highlight knowledge gaps for how post-wildfire debris-flow susceptibility varies throughout the western United States and worldwide and identify research needs to improve hazard assessment methods in different geographies.

Book chapter↗
USGS2024

Federal lands greenhouse gas emissions and sequestration in the United States: Estimates for 2005–22

In 2016, the Secretary of the U.S. Department of the Interior requested that the U.S. Geological Survey (USGS) produce a publicly available and annually updated database of estimated greenhouse gas emissions associated with the extraction and use of fossil fuels from Federal lands. The first report in this series included emissions estimates from 2005 to 2014 and were reported for 29 States and two offshore areas. Native American and Tribal lands were not included in that analysis. This report recalculates those previous years (2005–14) with updated data and methods and extends the estimates to 2022. Nationwide emissions from fossil fuels produced on Federal lands in 2022 were 1,081.2 million metric tons of carbon dioxide equivalent (MMT CO 2 Eq.) for CO 2 , 33.4 MMT CO 2 Eq. for methane (CH 4 ), and 4.3 MMT CO 2 Eq. for nitrous oxide (N 2 O). Compared to 2005, the 2022 totals represent decreases in emissions for all three greenhouse gases (by 17 percent for CO 2 , 37 percent for CH 4 , and 30 percent for N 2 O). Emissions from fossil fuels produced on Federal lands represent, on average, 21.8 percent of U.S. emissions for CO 2 , 6.1 percent for CH 4 , and 1.3 percent for N 2 O over the 18 years included in this estimate. The trends and relative magnitudes of the greenhouse gas emissions estimated are roughly parallel to the Federal lands fossil fuel production volumes. In 2021, Federal lands of the conterminous United States stored 70,424 MMT CO 2 Eq. in terrestrial ecosystems. Soils stored most of the terrestrial ecosystem carbon (66 percent), followed by live vegetation (25 percent), deadwood (5 percent), and litter (4 percent). Carbon sequestration on Federal lands was highly variable over time, owing primarily to interannual variability in climate and weather, and variability in land use and land cover (LULC) change and disturbances, among these are wildfires and logging. Between 2005 and 2021, Federal lands sequestered an average of 83 MMT CO 2 Eq./yr. By subtracting the cumulative effects of LULC and disturbance-related CO 2 losses to the atmosphere from the total, we estimate that ecosystems at the national level sequestered CO 2 at an annual mean rate of 17 MMT CO 2 Eq./yr in a term called the net ecosystem exchange (NEE). This annual NEE sequestration value represents about 1.4 percent of average fossil fuel emissions over the same period. The USGS estimates presented in this report represent an accounting for the emissions resulting from fossil fuel extraction on Federal lands and the end-use combustion of those fuels, as well as for the sequestration of carbon in terrestrial ecosystems on Federal lands. A combined net CO 2 emissions estimate, which is the difference between the emitted and sequestered CO 2 from both the fossil fuel and ecosystems estimates, provides context for evaluating the greenhouse gas contributions of activities on these lands. The estimates included in this report can provide context for future energy decisions, as well as a basis to track change in the future.

Scientific Investigations Report↗
USGS2024

U.S. Geological Survey Earthquake Hazards Program decadal science strategy, 2024–33

Executive Summary Earthquakes represent one of our Nation’s most significant and costly natural hazards, with estimated annual loses from earthquakes close to $15 billion in 2023. Over the past two centuries, 37 U.S. States have experienced an earthquake exceeding a magnitude of 5, and 50 percent of States have a significant potential for future damaging shaking; these statistics speak to the need for nationwide interest and investment in earthquake hazard characterization and risk reduction. Authorized under the Earthquake Hazards Reduction Authorization Act, the U.S. Geological Survey (USGS) Earthquake Hazards Program (EHP) provides the scientific information, situational awareness, and knowledge necessary to reduce deaths, injuries, and economic losses from earthquakes and earthquake-induced tsunamis, landslides, and soil liquefaction. The EHP supports activities in three focused topical areas: (1) earthquake monitoring, (2) hazard assessment, and (3) applied research, using the results of each—and the coordination among them—to further support risk translation and communication in regions at risk nationwide. For earthquake monitoring, the Advanced National Seismic System (ANSS), a cooperative effort of USGS networks, university partner regional seismic networks, and real-time geodetic networks, collects and analyzes data on earthquakes; issues timely, reliable notifications of their occurrence and impacts; and provides data for earthquake research, hazard, and risk assessment as a foundation for building an earthquake-resilient Nation. The USGS-operated ShakeAlert Earthquake Early Warning system is a recent addition to EHP’s ANSS infrastructure. In the realm of earthquake hazard assessment, the EHP contributes to earthquake risk mitigation strategies by developing the National Seismic Hazard Model and maps, and other related products, that describe the likelihood and potential effects of earthquakes nationwide, especially in the urban areas of highest risk. The EHP also conducts research on the causes, characteristics, and effects of earthquakes and prioritizes work that directly increases the accuracy and precision of earthquake hazards assessments, earthquake forecasts, and earthquake monitoring and situational-awareness products and that supports the Nation’s earthquake mitigation practices. Bridging the EHP’s efforts across research, hazard assessments, and earthquake monitoring is a broad and comprehensive collection of earthquake information products, including the National Seismic Hazard Model, ShakeAlert, and other products describing impact, such as ShakeMap and PAGER (Prompt Assessment of Global Earthquakes for Response), which have been developed and integrated into EHP’s real-time monitoring systems. EHP funds external partners to carry out many important collaborative activities through an active external grants program—one of the largest in the USGS—and through cooperative agreements with other partners such as the university-operated regional seismic networks, funded as part of the ANSS. To continue its support of earthquake hazard characterization and risk reduction, the EHP aims to strengthen its foundational products and practices while positioning itself to respond to the evolving needs of the Nation and follow best practices of the scientific community. This document describes a strategy for the program to ensure it can meet these demands. The foundational priorities outlined in this strategy represent those activities that remain critical to the core functionality of the program and those that can be supported under current fiscal year 2024-level appropriations. Priorities described as aspirational are important for future growth, and to maintain the program’s position as a leading global resource in earthquake science, but would require increases in appropriated funding to be fully realized. Across the program’s portfolio of activities, several major themes have been identified as the most critical activities to advance EHP science over the coming decade. Together, these activities provide the framework necessary to integrate critical hazard characterization and risk reduction activities across the program. They provide the structure for research to advance the understanding of where, when, and why earthquakes occur and how we can use improved knowledge to drive short-term and actionable forecasts of seismic activity. They expand the usefulness of critical earthquake products and advance the sophistication of those products to keep pace with the rapidly evolving needs of an ever-expanding user base while maintaining the position of the USGS as a global leader in earthquake science. Focus on system-level science. Establish an automated earthquake-processing pipeline. Enhance the accuracy and reliability of the ShakeAlert Earthquake Early Warning system and plan for extension to other regions. Implement time-dependent earthquake forecasting. Develop physically realistic models. Expand computational capacity. This science strategy is organized into three primary sections. The first section provides an overview of the EHP and its budget, governance, and program council. Readers familiar with the program may wish to focus on the second section, which describes the core of the science strategy, including priorities across each of the EHP’s major program activities in monitoring, hazard assessment, and targeted research. The third section outlines science priorities that cut across program activities, including those involving collaborations external to the EHP.

American Samoa, Guam, Northern Marianas Islands, U↗
USGS2025

Hydrogeologic characterization of the Cahuilla Valley and Terwilliger Valley Groundwater Basins, Riverside County, California

The relation between the groundwater and the amount of natural recharge to the Cahuilla Valley and Terwilliger Valley groundwater basins is not well understood. During the 20th century, the reliance on groundwater near Anza, California, used for agricultural, domestic, and municipal reasons has increased, and there is the potential for changes in groundwater availability related to climate change. Several types of existing data were evaluated, and new data were collected for this study, with the goal of characterizing the region’s hydrogeology. The study’s scope included constructing a geologic framework model to show where the groundwater-bearing units are present and their relation to each other, estimating the major components of the groundwater budget, and understanding local short-term and regional long-term groundwater flow and how that has changed since the early 1900s. Two electrical resistivity tomography surveys were done in the Durasno Valley about 2,150 feet apart to identify the thickness of the alluvium, its horizontal extent, and the depth-to-basement along two profiles perpendicular to Cahuilla Creek. The subsurface sediments were mostly horizontally layered and the transitional boundary between the alluvium and basement was thinner and shallower along the upgradient profile where the depth-to-basement was about 70 feet below land surface; the depth-to-basement at the downgradient profile was more than about 140 feet below land surface. The results from the surveys were used to place four monitoring wells at two sites along the survey profiles. Artesian flow from the deepest well at the downgradient site indicated that the decomposed and competent basement likely contributed some groundwater to the overlying alluvium, laterally, from below, or both. A digital three-dimensional geologic framework model was constructed using EarthVision software to represent the subsurface geometry of the alluvium, decomposed basement, and competent basement. Maps and cross sections of the modeled thicknesses of the alluvium and decomposed basement, and the modeled elevation of the top of the competent basement, were made to show the subsurface geometry of vertical faults, selected wells, and the groundwater-bearing units. Because natural recharge is related to the variable cycles of precipitation, estimates are difficult to quantify. Recharge and runoff have extreme interannual variability in the study area; recharge and runoff can be sporadic, and a substantive amount may not occur in some years. Estimates of recharge from a previous study and the regional-scale Basin Characterization Model for California for four different periods ranged from 3,800 acre-feet/year for 1897–1947 to 5,900 acre-feet/year for 1971–2000. Potential recharge from the disposal of domestic septic systems may have been as much as 500 acre-feet in 2020. It was estimated that between about 400 and 2,400 acre-feet/year of groundwater is lost through evapotranspiration by vegetation and evaporation from open water bodies, but the main source of discharge is through pumpage, mainly used for agriculture from the alluvium in the Cahuilla Valley and Terwilliger Valley groundwater basins. The estimated total pumpage for 1991–2021 ranged from about 1,140 acre-feet in 2019 to about 3,450 acre-feet in 1994. When summed, the cumulative amount of estimated pumpage between 1991 and 2021 was about 81,400 acre-feet. The general direction of groundwater flow is from the northeast along the San Jacinto fault zone at the headwaters of Cahuilla and Hamilton Creeks, to the surface-water outlets at the west and southeast parts of the study area. Groundwater-level data from the 1950s and earlier indicate that there was a natural groundwater divide between the Cahuilla Valley and Terwilliger Valley groundwater basins, but the changing magnitude and extent of the groundwater depressions caused by pumping since about 1950 indicate that the location of the natural groundwater boundary between the Cahuilla Valley and Terwilliger Valley groundwater basins has migrated over time. Flow from the upper to the lower parts of the Cahuilla Valley groundwater basin roughly follows the course of Cahuilla Creek through the narrow Durasno Valley where an estimated volume of flow in April 2019 was about 10–150 acre-feet/year. Short-term trends in groundwater levels, particularly in wells where groundwater is shallow and in the basement unit, show how some areas respond quickly to recharge and discharge. Wells located further to the east within the Cahuilla Valley groundwater basin in the alluvium show much less of a response to recharge events; areas of sustained pumpage from the alluvium, primarily for agriculture, show long-term declines in groundwater levels and generally do not show the effects of storm events or recent runoff. Groundwater levels in wells that are farthest from where most of the recharge occurs and where pumping has been the greatest, had some of the largest long-term groundwater-level declines at a rate of about 0.8 foot/year between 1971 and 2021.

California↗
USGS2024

Assessing spatial variability of nutrients, phytoplankton, and related water-quality constituents in the California Sacramento–San Joaquin Delta at the landscape scale—2018 high resolution mapping surveys

Executive Summary This study examined the abundance and distribution of nutrients and phytoplankton in the tidal aquatic environments of the Sacramento–San Joaquin Delta (Delta) and Suisun Bay, comprising three spatial surveys conducted in May, July, and October of 2018 that used continuous underway high frequency sampling and measurements onboard a high-speed boat to characterize spatial variation across the extent of the Delta. The method used involves simultaneously collecting information about the concentration and spatial distribution of all major nutrient forms with analogous information about the major classes of phytoplankton and associated water-quality conditions. The results showed substantial variation across space and time, providing an unprecedented snapshot of the dynamic environmental processes that shape the ways nutrients interact with and affect aquatic habitats in the Delta. The purposes of this study were to improve our understanding of how hydrodynamics, landscape features, and aquatic primary productivity interact to drive nutrient cycling and transport in the Delta and to provide insights into the underlying processes most directly responsible for the conditions at the time of this study, and thus into the range of conditions that may be expected following the wide array of prospective future changes to the Delta. One major anticipated change at the time of this study was the planned upgrade to the Sacramento Regional Wastewater Treatment Plant, but the study also informs our understanding of potential effects from other changes to the Delta, such as those caused by other nutrient-management actions, flow actions, large-scale wetland restoration, drought, flood, levee failure, and changes to water management. Nutrient loading is the primary driver of nutrient concentrations in the Delta, but several other major drivers interact to shape their distribution and effects: geomorphology, hydrodynamics, landscape features, and aquatic productivity. Hydrodynamics affect timescales of transport and dilution of nutrient loads in the Delta. During transit through the system, channel geometry, tidal mixing, and water exports affect hydrodynamics in diverse ways that influence water-residence and transport times, thereby markedly affecting the range of times during which natural internal cycling can alter nutrient concentrations and forms. Channel geometry and location shape tidal energy and river currents into these observed dynamics. Interactions with Delta aquatic landscapes such as herbaceous tidal marsh, submerged aquatic vegetation, and large expanses of intertidal or subtidal sediments (all highly productive landscapes) exert demand on available nutrient supplies but can also simultaneously transform and generate nutrients. Finally, while phytoplankton require nutrients to sustain production and thus are a potential nutrient sink, the amount and form of nutrients also can influence the occurrence of harmful algal blooms (HABs) that adversely affect aquatic organisms as well as affect the occurrence of beneficial algal blooms that result in production of algae that are favorable for imperiled Delta pelagic aquatic food webs. The surveys revealed a complex mosaic of spatial variation, with nutrient concentrations varying from near zero to well above concentrations considered eutrophic; nutrient concentrations were more often related to the extent of hydrologic transport and mixing than to specific geographic locations or to specific landscape features. Similarly, the surveys identified phytoplankton abundance ranging from near detection to the level of large phytoplankton blooms, with large variation in phytoplankton community composition. Although the study occurred during a period of low bloom activity, phytoplankton productivity appeared to be the strongest potential sink for inorganic nutrients in the Delta, indicating that it is a larger control on nutrient concentrations and distribution than previously understood. Cycling and transformation within the water column only appeared to substantially lower total nutrient concentrations at the longest estimated transport timescales. Contrary to expectations, we did not observe substantial nutrient depletion near landscape-scale features such as open-water habitats, submerged aquatic vegetation beds, extensive wetlands, or exposed sediments, indicating that these habitat types did not act as major sinks for nutrients in the Delta during these surveys. These results indicated that nutrient reduction efforts may have the greatest effect on pelagic phytoplankton productivity in the more productive reaches of the Delta and estuary, but these effects are unlikely to be magnified by changes to nutrient loss within the Delta over conceivable changes in flow conditions, Delta water management actions, or large-scale wetland restoration activities. Nevertheless, local processes were shown to cause substantial loss, and thus integrating of nutrient effects with other indicators of aquatic habitat conditions will help inform planning future actions at specific sites. Finally, we note that the primary contribution of this study was intended to be the survey data themselves. Aside from the results highlighted in this report, the surveys are a benchmark against which future environmental change may be evaluated, including changes to nutrient management or water exports, drought, large-scale wetland restoration, and climate change. Further, although we highlight some of the main findings from the surveys in this report, the necessarily limited scope precludes examination of many topics for which these surveys may be highly informative. To facilitate the utility of these data to stakeholders, managers, and researchers, we have released the data online (Bergamaschi and others, 2020) and created an online data exploration portal ( https:​//ca.water​.usgs.gov/​bay-​delta/​2018-​delta-​wide-​mapping-​surveys.html ) where users may query the surveys in a variety of ways to test hypotheses, examine relationships, assess spatial trends, and download data. The data exploration portal is intended to be an immersive experience that allows users to gain greater understanding of the complex interactions that shape Delta aquatic environments. This report is intended as a companion to the portal, allowing the reader to challenge and further explore the highlighted findings. This study was a collaboration between the U.S. Geological Survey and the Delta Regional Monitoring Program, with additional funding provided from U.S. Geological Survey Cooperative Matching Funds Program.

California↗
USGS2024

Streams, springs, and volcanic lakes for volcano monitoring

Introduction Volcanic unrest can trigger appreciable change to surface waters such as streams, springs, and volcanic lakes. Magma degassing produces gases and soluble salts that are absorbed into groundwater that feeds streams and lakes. As magma ascends, the amount of heat and degassing will increase, and so will any related geochemical and thermal signal. Subsurface magma movement can cause pressurization that alters hydrostatic head and may induce groundwater discharge. Fluid-pressure changes have been linked to distal volcano-tectonic earthquakes (White and McCausland, 2016; Coulon and others, 2017) and phreatic eruptions (for example, Yamaoka and others, 2016). Clearly, changes in groundwater and surface waters are both indicators of unrest and clues to how and where magma is rising toward the surface. Where possible, it is prudent to incorporate real-time hydrologic data into multiparameter monitoring of restless volcanoes. Hydrologic dynamics can also be tracked by changes in groundwater levels that are commonly measured in shallow boreholes (see of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume, on boreholes; Hurwitz and Lowenstern, 2024). Although inferred to be common, relatively few volcano-hydrology anomalies are well documented, and many are essentially anecdotal (Newhall and others, 2001), reflecting the fact that high-resolution time series remain rare. Extreme examples include the 2008 eruption of Nevado del Huila, Colombia, where relatively minor phreatomagmatic eruptions were accompanied by expulsion of as much as 300 million cubic meters of groundwater from fissures high on the volcano (Worni and others, 2011), generating large lahars. Substantial decreases in flow rate from springs about 8 kilometers from the summit of Mayon Volcano, Philippines, have been noted before most eruptions in the 20th century (Newhall and others, 2001). Stream monitoring at Redoubt Volcano in 2009 allowed Werner and others (2012) to recognize that groundwater was unable to absorb (or scrub) the high flux of volcanic gas and that a high CO 2 /SO 2 precursor signal had been evident for 5 months prior to the eruption. A key to better interpreting hydrologic anomalies—or even identifying them—is therefore obtaining adequate baseline data. Most hydrologic monitoring at U.S. volcanoes has been accomplished by intermittent sampling surveys with annual or less frequent sampling (for example, https://hotspringchem.wr.usgs.gov/index.php ). More frequent sampling, however, generally is needed to establish reliable baselines. A recent hydrologic and hydrothermal monitoring experiment at 25 sites and 10 of the 12 level 4 (very high threat) volcanoes in the U.S. portion of the Cascade Range demonstrated that there is sufficient temporal variability in hydrothermal fluxes, even during quiescent periods, that one-time measurements will commonly have limited interpretive value (Crankshaw and others, 2018). Thus, surveys are best augmented with data from streamgages (for example, Evans and others, 2004; Bergfeld and others, 2008). Streamflow (water discharge) data allow measured temperature and specific conductance to be converted to heat and solute mass fluxes, which could be insightful parameters for detecting anomalous activity (McCleskey and others, 2012). At the Yellowstone Caldera, long-term monitoring of river solutes has allowed calculation of the chloride flux, a proxy for heat discharge (Hurwitz and others, 2007; McCleskey and others, 2016) from the subsurface magma. This is readily accomplished because data from streamgages are continuously recorded and archived by the U.S. Geological Survey (USGS) National Water Information System (NWIS) (USGS, 2024). Similar studies on stratovolcanoes or shield volcanoes would be scientifically useful, and yet are logistically challenging, requiring streamgages on numerous radial drainages complemented by either frequent manual sampling or numerous deployments of equipment to measure water temperature and specific conductance as a proxy for water chemistry. Another challenge is that some volcanic areas, especially shield volcanoes, are characterized by near-surface porous rocks and soils, such that surface streams are rare and replaced by distant, dilute large-volume springs with only a trace of any original volcanically sourced water (Manga, 2001; Hurwitz and others, 2021). Volcanic lakes are worthy of special attention for monitoring efforts, as their temperature and composition can provide evidence of increased flux of volatile-rich fluids from below. Quantifying changes in volatile and heat release from magma can be simpler in lakes than for volcanoes with radial drainages and no major lakes. Moreover, volcanic lakes pose a range of hazards themselves, including phreatomagmatic eruptions, debris flows, flank collapse, tsunamis, and toxic gas release (Mastin and Witter, 2000; Delmelle and others, 2015; Manville, 2015; Rouwet and others, 2015)—hazards that have historically been responsible for substantial loss of life at many volcanoes worldwide (Manville, 2015). Catastrophic CO 2 release at Lake Nyos, Cameroon, in 1986 suffocated about 1,750 people and about 3,500 livestock and was probably triggered by a large landslide into the gas-saturated lake (Kling and others, 1987; Evans and others, 1993). Gas-charged springs in Soda Bay within Clear Lake (California) have caused almost a dozen deaths to bathers in the past hundred years (ABC News, 2000). A 2005 example of lake overturn and abundant gas release was documented at Mount Chiginagak in Alaska (Schaefer and others, 2008) but did not result in any human casualties. Although thermally stratified lakes, which promote trapping of exsolved magmatic gas, tend to develop in tropical regions, the phenomenon can also arise where salinity creates meromixis (a condition in which a lake does not mix completely), as occurs in Mono Lake, California (Jellison and Melack, 1993; Jellison and others, 1998). If magma erupts or flows into a lake, the interaction between hot magma and cold water can be explosive (Mastin and others, 2004; Zimanowski and others, 2015) and substantially expand the area affected by the eruption. Another hazard is the breaching of crater rims by landslides triggered by volcanic and (or) seismic activity. Under some circumstances, substantial volumes of water can be displaced, leading to large floods and lahars. Late Holocene lake flooding from Aniakchak Crater in the Alaska Peninsula (Waythomas, 2022) and from Paulina Lake in Newberry Crater, Oregon (Chitwood and Jensen, 2000), caused by the failure of outlet sills, testify to the substantial hazards at lake-filled calderas. Several volcanic systems in the United States host lakes known to receive heat and gas from underlying magma. These lakes vary widely in area, depth, and chemical composition. Lakes are present at level 4 volcanoes, including Crater Lake and Newberry Volcano in Oregon; Yellowstone Caldera in Wyoming; Long Valley Caldera, Clear Lake volcanic field, Medicine Lake, and Salton Buttes in California; and Aniakchak Crater, Mount Katmai, Fisher Caldera, Mount Okmok, and Kaguyak Crater, among others, in Alaska. A water lake was present in Halemaʻumaʻu, the crater of Kīlauea, Hawai‘i (fig. F1), from October 2019 to December 2020. Level 3 volcanoes with lakes include Mono Lake volcanic field (Calif.), Mount Bachelor (Ore.), Ukinrek Maars and Mount Chiginagak (Alaska), and Soda Lake (Nevada). In addition, there are lakes at many levels 1 and 2 volcanoes. In the United States, there are no strongly acidic lakes that receive abundant input of magmatic gas, such as those found at Mount Ruapehu (New Zealand), Ijen and Kelud (Indonesia), and Poás (Costa Rica). Nevertheless, many contain fluids that provide clues to magmatic processes below. Since publication of a previous report on recommended instrumentation for volcano monitoring (Moran and others, 2008), continuous hydrologic monitoring has become increasingly feasible. However, changes in water pressure, temperature, and chemistry remain, in general, poorly studied phenomena at volcanoes (Sparks, 2003; National Academies of Sciences, Engineering, and Medicine, 2017). Recent efforts by the USGS have included the temporary study of Cascade Range volcanoes, which included frequent (15 minute to hourly) temporal sampling of temperature, depth, and conductivity (Crankshaw and others, 2018; Ingebritsen and Evans, 2019). At Yellowstone Caldera, many streamgages have now added thermistors and specific conductance sensors, allowing estimation of time-dependent chloride flux as a proxy for variations in subsurface heat flux (McCleskey and others, 2012, 2016). Efforts to better understand lakes have also accelerated, with bathymetric mapping and sampling carried out at several locations in the United States. Especially thorough work was done at Yellowstone Lake thanks to the Hydrothermal Dynamics of Yellowstone Lake (HD-YLAKE, https://hdylake.org ) project, funded primarily by the National Science Foundation. In addition to geophysical surveys and recovery of cores and other samples, HD-YLAKE investigations included remotely operated vehicle (ROV) investigations of hydrothermal vents on the lake floor (fig. F2). Data collected by the ROV provided a better understanding of the thermal and chemical influx from lake-bottom hydrothermal systems (Sohn and others, 2017). In this chapter, we focus on detecting changes in the chemistry, temperature, discharge, or water levels of streams, springs, and lakes that can be caused by seismicity, volumetric strains, or increases in gas flux associated with ascending magma. There is unavoidable overlap with other chapters of this report. Samples of water and gas can also be obtained in boreholes ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume; Hurwitz and Lowenstern, 2024), both shallow and deep. Gas monitoring ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–E, 11 p., https://doi.org/10.3133/sir20245062e.">chapter E , this volume; Lewicki and others, 2024) relies in part on samples from springs and wells, particularly where measurable gas plumes are absent. Water acts as a trigger and lubricant for landslides and sediment-rich floods, and so hydrology has obvious relevance for lahar monitoring, as discussed in of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–H, 6 p., https://doi.org/10.3133/sir20245062h. ">chapter H (this volume; Thelen and others, 2024). Shared situational awareness among scientists engaged in geophysical, gas, and hydrologic monitoring will improve overall understanding of the volcanic hazard.

Scientific Investigations Report↗
USGS1973

Geohydrology of the Cross-Florida Barge Canal area, with special reference to the Ocala vicinity

The Cross-Florida Barge Canal route commences at Palatka on the St. Johns River, about 75 miles upstream from the Atlantic Ocean, and extends 110 miles southwestward across Peninsular Florida into deep water in the Gulf of Mexico near Yankeetown. The canal will be equipped with five locks, each 600 feet long and 84 feet wide, and the channel will be a minimum of 12 feet deep and 150 feet wide. From near Ocala northeastward, the canal channel will replace much of the natural channel of the Oklawaha River, and will be excavated into beds of the so-called shallow sand aquifer of Miocene age and younger, which overlies limestone of the Floridan aquifer. Westward from Ocala, most of the canal will be excavated below the potentiometric surface into limestone and dolomite of the Floridan aquifer. Water levels of Rodman, Eureka, and Inglis Pools will be controlled by dams and spillways with the limited exchange of water between the pools and the aquifers. The water levels in the Summit Pools will fluctuate with the natural changes in the ground-water level of the Floridan aquifer, although the stage of the pool will be controlled partly by the stage held in the Eureka Pool. A dynamic inflow-outflow relationship will exist between the Summit Pool and the Floridan aquifer. The Floridan aquifer in the canal area is 1,000 to 1,200 feet thick and consists of limestone and dolomite of middle Eocene Miocene age, including from older to younger, the Lake City, Avon Park, and Ocala limestones plus permeable sandy, dolomitic limestone in the lower part of the Hawthorn Formation. It is possible that most of the flow to the two major springs in the area occurs in the upper 100 feet or so of the aquifer in the Ocala Limestone. The aquifer is underlain by the Oldsmar limestone of early Eocene age and is overlain by sand, clayey sand, clay and shell beds of Miocene through Holocene age, in thickness from a few feet to 300 feet. The permeable beds overlying the Floridan aquifer constitute the shallow aquifer, while the poorly permeable ones act as confining beds where the Floridan aquifer is under artesian conditions. A north-south line drawn separating the head of Silver Springs on the west from the Oklawaha River on the east marks the approximate western limit of a continuous blanket of materials of Miocene-Pliocene(?) age covering the rocks of the Floridan aquifer. East of the line, much of the aquifer is under artesian conditions, particularly in the Oklawaha River valley, although in some areas east of the valley, direct recharge through thick permeable Miocene-Pliocene(?) sands occurs. West of the line, only scattered remnants of a once continuous Miocene-Pliocene(?) cover remain. Lack of the cover is a result of erosion on the crest and flank of the Ocala Uplift, a broad northwest-southeast trending anticlinal upwarp, the axis of which is crossed by the canal route in the Dunnellon area. Over most of this area the Floridan aquifer is unconfined and receives direct recharge through a cover of a few tens of feet of sand and clayey sand of Quaternary age. Tensional stresses during the structural evolution of the Ocala Uplift produced an intersecting system of fractures and normal faults in rocks of the Floridan aquifer. The fractures and faults are important controls for orientation of solution channels and, therefore, for development of ground-water circulation patterns. When the system surface streams, which once drained the Barge Canal area, eroded the poorly permeable Miocene-Pliocene(?) cover from the flanks of the Ocala Uplift, surface runoff was reduced and precipitation began to directly infiltrate the underlying limestones. Now only principal streams remain, such as the Oklawaha and Withlacoochee Rivers and a few short tributaries, while one of the most highly developed subsurface drainage systems in the world has evolved in cavernous limestone of the Floridan aquifer. Two of the larger freshwater springs in the world now discharge from the Floridan aquifer in the canal area. Silver Springs near Ocala discharges an average 531 mgd (million gallons per day) down the 4-mile long Silver River, which flows on poorly permeable beds to the Oklawaha River. Rainbow Springs near Dunnellon discharges on average 468 mgd from numerous orifices in the bed of the 5-mile-long Rainbow River, which flows into the Withlacoochee River. The heads of the springs have migrated to their present positions partly because of a tendency of ground-water levels to decline as permeability in the aquifer is increased due to removal of limestone by solution, and because of mechanical erosion of the limestone in the vicinity of the spring heads. Also, points of principal spring discharges have shifted in the past due to changes in ground-water levels in response to changes in sea level. The subsurface drainage system is continuing to evolve today, as evidenced in part by frequent occurrence of new sinkholes and by the presence of significant amounts of calcium bicarbonate in the spring waters. Rodman Pool, at the east end of the canal, is separated from the Floridan aquifer by poorly permeable materials. The pool's operating water level will be only a few feet above the potentiometric surface at the downstream end, and at or slightly below the potentiometric surface at the upstream end. Little exchange of water between the Rodman Pool and the Floridan aquifer is expected. Eureka Pool, just upstream from Rodman Pool, will also be separated from the Floridan aquifer by poorly permeable beds. However, the stage of the pool will be about 15 feet higher than the natural potentiometric surface at the pool's downstream end, and some seepage into the Floridan aquifer is anticipated through faults and leaky parts of the poorly permeable beds, with a consequent rise in ground-water levels in areas adjacent to the lower end of the pool. Possibilities for particulate contamination of the aquifer will tend to be minimized because of the filtering capacity of the materials through which water must pass to reach the aquifer, although the natural filter will not preclude movement into the aquifer of contaminants which might become dissolved in the pool waters. No significant interchange of water between the pool and the aquifer is expected at the upstream end of the Eureka Pool. Present construction plans indicate an operating stage for Eureka Pool which will range between 38 and 40 feet above mean sea level, although it is possible to dredge the pool deep enough to permit a range in stage of 36 to 40 feet. A backwater effect extending up Silver River from the Eureka Pool is expected to regulate the stage at the head of Silver Springs between 39 and 44 feet above mean sea level if the pool ranges between 36 and 40 feet. If Eureka Pool ranges only between 38 and 40 feet, the range of stage at the head of the springs should be about 41 to 44 feet above mean sea level. From Inglis Lock west, the canal will have direct connection with the Gulf, and canal stage will fluctuate with the Gulf tide. Since the canal stage will be slightly lower than the adjacent ground-water levels along much of the reach, there will be some ground-water inflow to the canal. No significant changes in the existing ground-water regime are expected in the vicinity of Inglis Pool, the first step up in the canal east of the Gulf. Existing ground-water and surface-water levels in the area will not change appreciable, and the natural stage and flow of Rainbow Springs, which will flow by way of Rainbow River into Inglis Pool, should not be affected by canal operations. A possible adverse effect of the canal on the Inglis Pool area could result if sea water is locked up from the Gulf through Inglis Lock. However, the high step of 25 feet at the lock, flushing action of continuous flow from Inglis Pool to the lower reaches of the Withlacoochee River, and use of possible preventive locking procedures should minimize the problem. The potential for adverse effects on the ground-water regime is greatest in the area of the Summit Pool. Through most of the length of the pool, the canal channel will be excavated into limestone of the Floridan aquifer to depths of 12 to 27 feet below the potentiometric surface. Changes that will take place in the ground-water flow system in the Silver Springs drainage area, once the canal is completed, were estimated by flow-net analysis. Variation in aquifer transmissivity was determined by calculating transmissivity in 25 different flow cells surrounding Silver Springs. Transmissivity in the 25 cells averages about 15,600,000 gpd/ft [2,090,000 ft2/day (feet squared)], but transmissivity in the six cells through which the Summit Pool passes ranges from 9,000,000 to 44,000,000 gpd/ft (1,210,000 to 5,900,000 ft2/day). Transmissivity was used to compute static stage of the Summit Pool under given ground-water level conditions. Had the canal existed in May 1968 and had the stage of Eureka Pool been held at 36 feet at the time, the static stage in Summit Pool would have been about 42.1 feet above mean sea level. Thus, a conceptual model of the changes in the potentiometric surface wrought by the finished canal was drawn, and zones of ground-water inflow and outflow were delineated. Most outflow from the Summit Pool to the aquifer should be limited to one 4-mile-long zone along the north side of the pool, about 5 miles south of Silver Springs. It is estimated that a water volume equivalent to about 8 percent of the daily flow of Silver Springs will enter the Summit Pool each day from the southern one-third of the Silver Springs drainage area. A like amount will reenter the aquifer at the main zone of outflow and move toward Silver Springs at an estimated average velocity of about 200 feet per day, if something close to the natural static stage of the pool is maintained by return pumpage of the lockage losses. At a velocity of 200 feet per day, water from the Summit Pool would discharge at Silver Springs about 140 days later. However, any estimate of velocity in the highly cavernous limestone aquifer in the area should be used with caution, because difficult to measure changes in porosity and thickness of major zones of flow may cause large variations in velocity. If all lockage losses are returned to the Summit Pool by pumping from Eureka Pool, no net loss from the Silver Springs drainage area, except for some evaporation from the water surface in the canal and possible leakage around locks, will result from canal operations. The zone of outflow from the Summit Pool to the aquifer will be in a natural potentiometric trough, and the zone of inflow will be in a potentiometric ridge area. The equilibrium water level in the pool will tend to be about 1 foot higher than the altitude of the lowest level in the pre-canal potentiometric trough, and about 2 feet lower than the highest level on the pre-canal potentiometric ridge. West of the Silver Springs drainage area just east of Dunnellon Lock, in the area of a local potentiometric high, the water level in the Summit Pool is expected to be about 15 feet below the natural potentiometric surface. In most areas 2 to 3 miles away from the Summit Pool, effects of the canal on the natural potentiometric surface should be slight. The stage of the Summit Pool, judging from the 36-year record for ground-water level changes and the anticipated indirect effect of the controlled stage in Eureka Pool, should have a maximum of about 10.5 feet with a maximum water level of about 51.5 feet above mean sea level and a minimum of about 41.0 feet above mean sea level. Of particular importance in the Summit Pool is an implementation of well planned construction and operational procedures designed to minimize risks of ground-water contamination.

Florida↗
USGS2024

Reservoir evolution, downstream sediment transport, downstream channel change, and synthesis of geomorphic responses of Fall Creek and Middle Fork Willamette River to water years 2012–18 streambed drawdowns at Fall Creek Lake, Oregon

Executive Summary Chapter A. Introduction Fall Creek Dam impounds Fall Creek Lake, a 10-kilometer-long reservoir in western Oregon and is operated by the U.S. Army Corps of Engineers (USACE) primarily for flood-risk management (or flood control) in late autumn through early spring months, as well as for water quality, irrigation, recreation, and habitat in late spring through early autumn. Since 2011 (water year [WY] 2012), Fall Creek Lake has been temporarily drawn down each year to facilitate downstream passage of juvenile spring Chinook salmon ( Oncorhynchus tshawytscha ) through the 55-meter (m) high dam. This annual dam operation is temporary, typically lasting about 1–2 weeks from WY 2012 through 2020 (drawdown operations in WY 2022–24 have increased to more than 6 weeks). Drawdown of the reservoir results in lake levels being lowered to the elevation near the historical, pre-dam streambed. The annual streambed drawdowns of WY 2012–18 have improved fish passage and led the USACE to formally adopt streambed drawdowns as part of annual operations at Fall Creek Dam. However, temporarily lowering the lake to streambed creates free-flowing conditions in the reservoir that result in the erosion and episodic export of predominantly sand and finer-grained sediments (less than 2 millimeters [mm]) to the lower gravel-bed reaches of Fall Creek and the Middle Fork Willamette River. The introduction of large volumes of sand and finer-grain sediment into the dam-regulated reaches downstream from Fall Creek Dam prompted questions about the geomorphic responses to annual streambed drawdowns within Fall Creek Lake and downstream reaches along Fall Creek and the Middle Fork Willamette River. The U.S. Geological Survey (USGS) in partnership with USACE initiated a comprehensive geomorphic and sediment transport investigation to assess the coupled processes of reservoir erosion, sediment evacuation from Fall Creek Lake, and patterns of sediment transport and deposition in reaches downstream from the Fall Creek Dam that have resulted from annual streambed drawdowns. The purpose of this report is to systematically describe the processes of sediment erosion, transport, and deposition at Fall Creek Lake and geomorphic interactions between reaches upstream and downstream from Fall Creek Dam that relate to dam operations. Specifically, this report focuses on evaluating geomorphic responses to streambed drawdowns from WY 2012 through 2018 and placing drawdown-induced geomorphic responses within the broader context of physiographic and historical conditions and dam operations of Fall Creek and Middle Fork Willamette Rivers. Key objectives for this study were to characterize changes in reservoir morphology and substrate at Fall Creek Lake, describe the character and temporal pattern of sediment transport downstream from Fall Creek Dam, characterize geomorphic changes in channel reaches downstream from the Fall Creek Dam, and relate these data to the annual streambed drawdowns of WY 2012–18. This study uses multiple independent monitoring and measurement approaches to assess site, reach, and river-scale geomorphic responses to drawdowns to inform dam and reservoir management. Patterns and processes of reservoir evolution were assessed with geomorphic mapping and volumetric analyses of topography through comparison of multiple digital surface models (DSMs). Just downstream from Fall Creek Dam, analyses of sediment export from the reservoir focused on suspended sediment but also incorporated bedload analyses to assess sediment sizes. Geomorphic assessments downstream from the dam used reach-scale and site-scale approaches to document changes in channel morphology and substrate, including site measurements of sand and finer-grained sediment deposition and in-channel bed-material, volumetric change analyses from comparison of digital elevation models (DEMs), and repeat geomorphic mapping. Findings from this study inform river management and dam operations by providing an understanding of (1) coupled upstream-downstream geomorphic responses to the Fall Creek Lake streambed drawdowns, (2) geomorphic responses of Fall Creek Lake streambed drawdowns in comparison to drawdowns at other large dams, (3) controls on reservoir erosion and downstream geomorphic responses, and (4) implications for future hydrogeomorphic changes that may result from continued drawdowns and monitoring activities to assess those changes. Chapter B. Reservoir Morphology and Evolution Related to Dam Operations at Fall Creek Lake To understand the volume and distribution of sediment accumulation in Fall Creek Lake since dam closure in 1965, decadal-scale sedimentation patterns (spanning approximately 1965–2016) are evaluated using a combination of storage curve analyses and geomorphic mapping. Short-term (drawdown event-scale) patterns of erosion, sedimentation, and sediment export downstream are evaluated using a combination of geomorphic mapping and change detection analyses that quantify the distribution and total volume of sediment erosion and deposition within Fall Creek Lake. Geomorphic mapping of reservoir topography and analyses of historical datasets reveals four categories of landforms and sediment processes within Fall Creek Lake related to lake level operations: lacustrine sedimentation expressed in the reservoir floor, fluvial erosion and deposition within historical stream channels during streambed drawdowns, channel-like features created by erosion within the reservoir floor during streambed drawdowns, and erosion on reservoir hillslopes. Where the reservoir floor is mapped for this study as pelagic (deep water), deposition up to 3 meters (m) thick by lacustrine processes and burial of pre-dam topography with deposits thinning toward the edges of the valley floor and upstream areas of reservoir are observed. Despite over 50 years of sediment accumulation since dam construction, the main stream channels of Fall and Winberry Creeks (or reservoir thalwegs) through the reservoir are well defined, though their distinct morphology is likely influenced by a long history of recurring historical drawdowns to or near streambed since dam construction. Unregulated streamflow and sediment transport through the reservoir primarily are confined to these channels during the streambed drawdown periods. Erosional channel-like features created by drawdowns are carved through underlying, unconsolidated reservoir floor sediments and are most prominent in the lower reservoir below minimum conservation pool (the low pool elevation during winter flood season); sediment generated from the formation of these drawdown channels is more likely to be transported through and out of the reservoir than sediment deposits along the reservoir hillslopes at the valley margins that are separated from main channels by areas of low-gradient reservoir floor. Morphologic changes in the lower reservoir topography between January 2012 and November 2016 indicate overall net erosion of about 129,500 cubic meters (m 3 ). The most prominent geomorphic changes occurred along the main channels of Fall and Winberry Creeks near the Fall Creek Dam where incision, lateral migration, and slumping banks resulted in vertical and lateral adjustments to channel position, whereas most changes fell below the detectable limit on higher-elevation reservoir floor surfaces except where erosion occurred along features mapped as drawdown channels. Chapter C. Sediment Delivery from Fall Creek Lake and Transport through Downstream Reaches USGS implemented a sediment monitoring program in WY 2013–18 to evaluate the quantity and character of reservoir sediment exported from Fall Creek Lake during streambed drawdowns. Turbidity and suspended sediments were monitored annually autumn through spring to span the WY 2013–18 streambed drawdowns; however, unequal monitoring timeframes each year reduced the ability to compare results and factors affecting sediment export from the reservoir difficult between years. These data were originally measured to develop regressions and compute suspended-sediment loads (SSL). Bedload sediment monitoring from a cableway at the Fall Creek streamgage was completed in the autumn-winter of WY 2013 and 2017. The limited number of samples and presumed variability in sediment supply from the reservoir precluded construction of streamflow and bedload discharge relations to compute more than instantaneous bedload. Sand and finer-grained silts and clays were transported from the reservoir in suspension, though some coarser grains (up to 32 mm) were also mobilized and transported downstream from the dam as bedload. Observations of increased sediment transport downstream from Fall Creek Dam coincided with lake levels approaching about 3 m (10 feet [ft] or elevation 690 ft) above the streambed regulating outlets. Suspended-sediment loads computed for the full monitoring periods WY 2013–18 at the Fall Creek streamgage, located 1.4 kilometers (km) downstream from Fall Creek Dam, range from 54,700 metric tons (t) in WY 2013 to 13,900 t in WY 2018. Although the total annual SSL varied from year to year, the overall seasonal patterns of suspended sediment transport throughout each year were similar during monitoring in WY 2013-18. Suspended-sediment loads were low prior to the drawdown, then increased rapidly as lake levels lowered and approached the streambed. In the weeks following the drawdown period, as pool levels were increased, SSL remained slightly elevated above pre-drawdown levels but generally declined through the following winter and spring except during streamflow-driven pulses of suspended-sediment transport. WY 2013 had the greatest total computed SSL for each streambed drawdown and partial-year monitoring period. SSL computed for the partial-year period have generally decreased since WY 2013 and have varied by about 6,800 t with the exception of WY 2014. WY 2014 SSL reflects anomalously low sediment export due to low streamflows and freezing conditions that stabilized reservoir floor deposits. Bedload measurements in the short 1.4-km reach between Fall Creek Dam and the Fall Creek streamgage showed an inverse correlation between bedload transport rates and discharge, which probably reflects diminishing supply of coarse-sized sediment. Sand was more abundant (60–100 percent) than gravel in bedload samples confirming sand and finer-grained sediment dominated sediment evacuated from the reservoir during streambed drawdowns at Fall Creek Lake. Chapter D. Geomorphic Responses to Fall Creek Lake Streambed Drawdowns Downstream from Fall Creek Dam In the days, weeks, and months following streambed drawdown operations at Fall Creek Dam through WY 2018, sites downstream from the dam displayed a variety of geomorphic responses to reservoir sediment delivery within the main channel and overbank areas. Evaluation of streambed elevations at two streamgages located 1.4 km downstream from the dam on Fall Creek and 16.3 km downstream from the dam on the Middle Fork Willamette River indicated the effects of drawdown sediment on bed elevations were modest and transient. Repeat particle size measurements (October 2015 and September 2016) at five sites along Fall Creek and the Middle Fork Willamette River showed similar grain-sized distributions that do not reveal substantial deposition of fine-grained sediment related to the WY 2016 streambed drawdown. Altogether, these findings indicate that transport capacity in the main, low-flow channels of Fall Creek and Middle Fork Willamette River during WY 2012–18 was sufficient to mobilize and evacuate reservoir sediments from streambed drawdowns or other bank material and tributary sources. However, other monitoring for this study indicate low-velocity zones in off-channel areas are prime locations for sand and finer-grain sediment deposition. Patterns of overbank sediment accumulation indicate that the magnitude and timing of overbank deposition on bars and low-elevation floodplain varies with proximity to the dam, geomorphic setting, streamflows, and other factors. Sand and finer-grained reservoir sediments carried as suspended-sediment load in the reaches downstream from Fall Creek Dam were deposited in overbank areas as observed with clay-horizon markers during WY 2016–17. Overbank deposition quantified with Geomorphic Change Detection (GCD) software evaluated landform-scale patterns of erosion and deposition using repeat light detection and ranging (lidar) surveys at two sites in the Upper Fall Creek reach and one site in the Jasper reach for 3 years (2012–15) and one site in the Clearwater reach for 6 years (2009–15). Deposition thickness and spatial patterns from the GCD analysis were variable; some sites had dispersed but measurable deposition while at others, deposition was highly localized and exceeded 1 m in depth. Patterns of overbank deposition illustrate interactions among bar morphology, local hydraulics, and suspended-sediment transport dynamics that can create patches of highly localized deposition. The measured deposition at the two Fall Creek GCD sites likely resulted from reservoir sediments released from Fall Creek Lake during streambed drawdowns in WY 2016 and 2017 because the limited sediment inputs from bank material (geomorphically laterally stable reach) or tributaries (no significant tributaries) provided few other sediment sources. On the Middle Fork Willamette River, observed patterns of overbank deposition could reflect sediment sourced from upstream tributaries, bank erosion, or Fall Creek Lake streambed drawdown operations. Despite the introduction of several thousand tons of reservoir sediment delivered from the Fall Creek Lake streambed drawdowns to below-dam river corridors, reach-scale mapping of channel features downstream from Fall Creek Dam shows minimal evidence of changes in channel planform or landforms that can be attributed to a drawdowns in WY 2012–16. On Upper Fall Creek reach, widespread increases in gravel bars or other in-channel sediment did not result from the five streambed drawdowns. The main changes attributable to sediment releases from Fall Creek Lake were localized increases in vegetated bar area, particularly on channel margin areas where sand and finer-grain sediment was deposited and rapidly colonized by vegetation. The area of mapped secondary water features decreased between 2005 and 2016, but that may be due to lower discharges depicted in the 2016 aerial photographs and less mapped area of inundation. Primary changes along the Lower Fall Creek reach include a 6.4 percent decrease in area of secondary water features between 2011 and 2016, and a nearly twofold increase in the area of unvegetated bars. Immediately downstream from the Fall Creek confluence, there were negligible changes in the location and areas of vegetated bars and the main wetted channel between 2005 and 2016, and local increases in bar area cannot be attributed solely to deposition of reservoir sediments from Fall Creek Lake because (1) areas along the Middle Fork Willamette River just upstream from the Fall Creek confluence display similar type and magnitude of changes and (2) some of the increases at the confluence area pre-date the drawdowns. The cumulative effect of sediment releases from Fall Creek Lake streambed drawdowns from WY 2012 to 2016 on downstream channel planform and landforms are modest compared to the river-scale transformations and planform changes that occurred in the decades following dam construction. Chapter E. Discussion of Geomorphic Responses of Fall Creek and Middle Fork Willamette River to Streambed Drawdowns at Fall Creek Lake Multiple aspects of Fall Creek Dam infrastructure and operations exert first-order controls on the magnitudes of reservoir erosion that occur during the streambed drawdowns and ultimately determine the sediment delivery to downstream reaches. Key aspects of the dam and its operations that are most relevant to assessing geomorphic responses to streambed drawdowns include the (1) dam infrastructure, including configuration and size of regulating outlets and their proximity to the streambed which dictates the capacity and competence of the river to deliver sediment to downstream reaches and mode of sediment transport as suspended-sediment load or bedload; (2) frequency of historical drawdowns and long-term, year-round dam operations and lake level management, which partly dictate reservoir morphology and locations and magnitudes of readily erodible materials; (3) dam operations and hydroclimatic conditions during the streambed drawdown (including length of the drawdown and streamflows entering the reservoir), which directly control the timing, duration and magnitude of reservoir erosion and sediment evacuation; and (4) dam operations following the streambed drawdown operation that regulate streamflows (and thereby sediment transport conditions) downstream of Fall Creek Dam which primarily reflect interactions between hydroclimatic conditions and flood control operations. Patterns of sediment erosion and evacuation observed in this study at Fall Creek Lake from WY 2012–18 suggest that reservoir erosion during annual streambed drawdowns may remain similar or decrease in future years assuming (1) annual streambed drawdown operations are implemented in similar manner as the WY 2012–18 drawdowns (in terms of duration, late autumn or early winter implementation, rate of pool-level lowering to reach streambed, and other factors), (2) streambed drawdowns coincide with similar conditions as were observed WY 2012–18 (similar sediment yield into reservoir, low reservoir inflows, limited precipitation, moderate air temperature), and (3) no major geomorphic changes in the main reservoir channels of Fall and Winberry Creeks occur (for example, channel avulsion). Under such conditions, it is hypothesized that the stream channel within the reservoir would achieve a quasi-equilibrium state with respect to annual influx and export of sediment and aided by the substantial amount of in-channel bedrock, will remain laterally stable without erosion across reservoir deposits. Patterns of sediment transport measured at the Fall Creek streamgage downstream from Fall Creek Dam provide insight into the potential effects of future streambed drawdowns at Fall Creek Lake. Analyses of suspended sediment measured in WY 2013–18 show a major reduction in suspended-sediment loads between WY 2013 and later years, indicating streamflows transporting sediment through the reservoir to downstream reaches during streambed drawdowns have become supply limited. The 6-year suspended-sediment monitoring and sampling program is insufficient to make predictions about future sediment transport conditions because of uneven monitoring periods and varying controls on reservoir sediment erosion. It is likely that future suspended-sediment loads will be variable but similar to those observed in WY 2015–18 if operational, climatic, and geomorphological factors remain similar to those monitored WY 2015–18. Suspended-sediment loads downstream from Fall Creek Lake will likely remain highest when regulating outlets are fully open and Fall Creek is free flowing with the reservoir fully drained with little to no residual pool. Over time, it is possible that the suspended-sediment loads would reflect mobilization of reservoir sediment deposited in the previous year rather than erosion of sediment deposited years or decades earlier. Bedload is likely to remain a small fraction of the total sediment load evacuated from the reservoir and is relatively modest compared with pre-dam bedload transport rates because most coarse sediment remains trapped by the dam. If sediment releases from Fall Creek Lake and ensuing streamflow conditions follow a similar pattern in the future as was assessed in this study spanning WY 2012–18, near-term geomorphic adjustments downstream of the dam are expected to be modest. Barring major operational, climatic, and geomorphological changes, local site-scale deposition on bars, overbank areas, or off-channel features that persists several months after the streambed drawdown will likely continue to be highly variable, ranging from negligible to several centimeters of deposition. At the landform-scale, low velocity areas nearest to Fall Creek Dam will likely continue to undergo rapid deposition immediately during and after a streambed drawdown event, similar to patterns observed for WY 2012–18. Some of the sediment entering these off-channel features and margin areas may be temporarily stored, then later remobilized and dispersed farther downstream. But if newly deposited sediment persists through the following spring, there is a greater likelihood that local vegetation will establish, reinforce deposited material, and trap sediment during later drawdowns. The reach-scale geomorphic changes may become more apparent if (1) streambed drawdowns continued for several decades, and geomorphic changes were measured at decadal scales or (2) the amount of sediment introduced to downstream reaches substantially increased and (or) sediment transport capacity decreased. The continued streamflow regulation of Fall Creek Dam after sediment releases provides an opportunity to strategically manage streamflows during and after the streambed drawdowns to minimize downstream sediment impacts and ensure other operational thresholds are satisfied. This study provides a comprehensive foundation of datasets and geomorphic analyses to inform dam operations at Fall Creek Lake, monitor sediment transport downstream, and consider operational schemes for future drawdowns. The datasets from this study also provide baselines of sediment transport and geomorphic conditions to assess future changes in reservoir and downstream environments. Future monitoring could be tailored to address specific questions regarding the long-term geomorphic effects of streambed drawdowns on fluvial habitats, flood hazards, cultural resources, or downstream water quality. Future monitoring activities could focus on the relevant geomorphic processes and spatial domains within the three categories used for this study: (1) reservoir erosion and net sediment evacuation, (2) sediment delivery to downstream reaches, including magnitude and temporal pattern of sediment transport, and (3) geomorphic responses of downstream reaches to sediment delivery. Specifically, high priority future monitoring activities could include: Repeat topographic or photographic surveys in the reservoir to characterize changes occurring within individual drawdowns, to quantify sediment export, to determine temporal changes in reservoir storage, and to identify locations of erosion and deposition. Continuous, year-round turbidity monitoring supplemented with suspended-sediment measurements at a streamflow-gaging station immediately downstream from the dam to quantify sediment export. Repeat geomorphic monitoring, mapping, or modeling in downstream reaches to track changes in channel and over bank features using a combination of site- and reach-scale monitoring approaches. This could support assessments of sediment deposition and ensuing vegetation encroachment on flood hazards and habitats and examine how sediment transport and depositional processes may be affected by different sediment supply, streamflow, or dam management scenarios.

Oregon↗
USGS1999

The effects of the Chesapeake Bay impact crater on the geological framework and correlation of hydrogeologic units of the lower York-James Peninsula, Virginia

This report documents the highly variable structure, stratigraphy, and buried topography of the outer rim of the Chesapeake Bay impact crater created by its impact and burial. Lithologies of cores are correlated with borehole geophysical logs to characterize the physical properties of the stratigraphic units and their geophysical signatures. The correlation between cores, well cuttings, and borehole geophysical logs is augmented with seismic-reflection data, and these data are compiled into a lithostratigraphic cross section that illustrates the geological framework of the lower York-James Peninsula and immediate surrounding areas.

Virginia↗
USGS2026

Preliminary geologic map of the Sparta East, Sparta West, and parts of the Glade Valley and Whitehead 7.5-minute quadrangles, North Carolina and Virginia, and the epicentral area of the August 9, 2020, Mw 5.1 earthquake near Sparta, North Carolina

Introduction New bedrock and surficial geologic mapping in the Sparta East, Sparta West, and parts of the Glade Valley and Whitehead 7.5-minute quadrangles, North Carolina and Virginia, investigates the geologic framework and causative mechanisms of the August 9, 2020, Mw 5.1 earthquake near Sparta, North Carolina. The mapping documents (1) the coseismic surface rupture from the 2020 earthquake and related brittle structures in the bedrock; (2) the fault contact between the western Blue Ridge and eastern Blue Ridge; (3) lithostratigraphy in the Lynchburg Group, Ashe Metamorphic Suite, and Alligator Back Metamorphic Suite; (4) the nature of the contact between the Lynchburg Group, Ashe Metamorphic Suite, and Alligator Back Metamorphic Suite; and (5) surficial deposits.

North Carolina, Virginia↗
USGS2025

Methodology for compilation of previously published contour data showing the altitude of the base of Dakota Sandstone on the Colorado Plateau, Arizona, Colorado, New Mexico, and Utah

Structure contours and other geologic information from numerous published geologic maps were digitized and compiled into a digital dataset showing the configuration of a single stratigraphic datum, the base of the Dakota Sandstone and its equivalents across the Colorado Plateau. The principal maps compiled in digital form are a series of 1:250,000-scale 1 degree (°) × 2° quadrangle maps published by the U.S. Geological Survey, augmented by other geologic maps published at various map scales. The compiled digital dataset contains geologic map polygons of the Dakota Sandstone and regional stratigraphic equivalents, the location of faults and fold axes, structure contour lines that define the altitude of the base of the unit and bedding orientation data computed from the structure contour lines. This report provides the scientific rationale for compilation of these data and describes the compilation methodology for each of the data elements. This report provides an extended description of the data compilation in a companion U.S. Geological Survey digital data release of spatial data and attributes associated with the contoured surface and associated geologic data layers.

Arizona, Colorado, New Mexico, Utah↗
USGS2026

Capitalization of positional (Lower/Middle/Upper) and temporal (Early/Middle/Late) adjectives in the names of formal chronostratigraphic and geochronologic units of the Phanerozoic

Many authors are understandably confused about the capitalization of the words “lower,” “middle,” “upper,” “early,” and “late.” Where these words are used simply as descriptive adjectives, they should be in lowercase; where they form the first word of a formal chronostratigraphic or geochronologic unit name, they should be in uppercase.

Professional Paper↗