Geology ReportsSearch

SEARCH · Geology Reports

Results for “Space Science Reviews”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

373 records · Page 15Linked to original sources

Non-radiometric borehole geophysical detection of geochemical halos surrounding sedimentary uranium deposits

Roll-type uranium deposits are formed by the concentration of uranium by ground water in geochemical cells. Non-uranium minerals having different solubilities may be deposited ahead of or behind the uranium minerals, forming halos that surround the ore. In addition, oxidizing and reducing environmental conditions may cause zones of mineral alteration to develop beyond the limits of the uranium deposit. Certain physical property anomalies that are commonly associated with halos can be detected by relatively fast and inexpensive borehole geophysical measurements made either in individual holes, or between two adjacent holes. Borehole measurements that have been found to be useful include electrical resistivity, induced polarization, and magnetic susceptibility. Electrical resistivity is increased by the presence of calcite and other cementing minerals that sometimes create permeability barriers in the neighborhood of uranium deposits. Induced polarization (IP) response is increased by sulfide and clay minerals that are commonly found in anomalous concentrations near roll-type deposits. Magnetic susceptibility is usually decreased by the oxidation of magnetite to hematite or limonite in the zone of chemical alteration that is left as a trail behind roll fronts. Borehole measurements of electrical resistivity, induced polarization and magnetic susceptibility were made in the vicinity of a uranium roll-type deposit in south Texas. Results indicate that mineral halos can be detected by borehole measurements made. in wide-spaced drill holes, and that the total amount of drilling needed to find a deposit can be reduced substantially by this exploration approach.

Open-File Report

Helium detection as a guide for uranium exploration

Helium, a byproduct of radioactive decay, may prove to be a valuable indicator of the presence and distribution of uranium deposits. Recent technological advances permit the development of instrumentation not previously adapted for this purpose. Commercially available equipment can provide high sensitivity at low cost and allow reasonable mobility for field use. A truck-mounted mass-spectrometer, tuned for helium-4, permits immediate adjustment or modification of sampling patterns in response to accumulating data. The inlet system of the spectrometer has been designed to allow flexibility in gas analyses from various sample types--soil gas, atmosphere, or gases in water. Sensitivity of the instrument is better than 50 parts of helium per 10 9 parts of gas. Replicate samples and standards can be analyzed in only 3 minutes. Helium in soil gas is being used for the initial evaluation of the technique. A hollow probe, as much as 2 m long, is driven into the ground; and a 10-cc syringe is used to purge the probe and extract the gas. This sample is then injected into the inlet system and introduced into the spectrometer at constant pressure. The output signal is displayed on a chart recorder. Investigations can be performed on a qualitative, relative basis, or on a quantitative basis by comparison to calibrated helium standards. Preliminary field testing includes studies of the responses to variations in wind speed, temperature, barometric pressure, moisture, and sampling depth over extended time periods, as well as studies of geologic controls on the helium content in soil gas. Surveys over known uranium occurrences reveal some anomalous helium distributions. This report describes an updated technological approach to an old idea: that of using helium, a byproduct of uranium radioactive decay, as an exploration tool for uranium. Helium is the sixth most abundant gas found in the earth's atmosphere (Table 1). It is an inert gas and very mobile, mixing rapidly. When the alpha particles from the radioactive decay of uranium and thorium pick up two electrons, atoms of the isotope helium-4 are formed. Several helium-4 atoms are produced from each decay series of U-238, U-235, and Th-232 (fig. 1). The half-lives of the parent isotopes are5also shown in figure 1. One gram of uranium will produce ~10 5 atoms of helium-4 per second, and one gram of thorium produces ~2.5 x 10 4 atoms of helium-4 per second (fig. 2). Calculations of the helium produced from the crust and mantle reveal that 1,125 x 10 30 atoms per year are produced, but only 7 x 10 30 atoms per year escape from the earth (Damon and Kulp, 1958). More is being produced than is being lost; in fact, the total atmospheric content of helium could be produced in only 2 million years (MacDonald, 1963)! However, all the crustal and mantle helium-4 does not degas into the atmosphere as it is formed. It is trapped in crystal lattices and in pore spaces within the earth. What this means is that there is excess helium-4 in the earth--excess, that is, compared to the atmospheric concentration in equilibrium with the helium-4 escape rate into space and the helium-4 flux from the crust and mantle (Nicolet, 1957). Near-surface pockets of high helium-4 concentrations are known, and some natural gas fields are so enriched that they are the source for commercial production of helium. Work by Roberts and others (1975) has shown high helium concentration in the soil gas associated with geothermal areas; and work by Clark and Kugler (1973), Dyck (1975), and Goldak (1974), for example, has noted high helium concentrations in soils and waters in the vicinity of uranium deposits. These latter studies certainly indicate the potential of helium detection for use as an exploration tool for uranium.

Open-File Report

Decadal-scale characteristics of natural and anthropogenic dune morphology along North Carolina Barrier Islands (SE Atlantic Coast)

Dunes offer protection to coastal communities from storms, yet quantitative research characterizing human influences on dune systems across decades and 10–100 km spatial scales constitutes a known data gap. This study analyzed a multidecadal archive of dune crest elevations and positions to map mesoscale spatiotemporal trends in foredune morphology across the barrier island coastline of North Carolina, SE Atlantic coast. Results are summarized within four categories of coastline representing a range of coastal management intensities, integrating beach width and dune lateral accommodation space to assess the comparative influence of differing intensities of anthropogenic intervention on dune morphology. These categories account for the presence of structures, roads, and alongshore connectivity to anthropogenic sediment sources (beach nourishment). These categories show distinct dune and beach system characteristics. Dunes are largest in the areas with the longest legacy of coastal management. As categories decrease in development intensity, dune and beach system characteristics generally depart from the large, static dunes and narrow beaches consistent with hold-the-line management. Where small or transgressive dunes exist on heavily developed coasts, they coincide with relatively strong hydrodynamic forcing or sediment-limiting geology. There is evidence of indirect coastal management influence on undeveloped barrier islands with alongshore connectivity to developed barriers. While this analysis was conducted at the mesoscale, the results provide researchers with the framework to make insights at smaller scales than those demonstrated in this study.

North Carolina

On connecting hydro-social parameters to vegetation greenness differences in an evolving groundwater-dependent ecosystem

Understanding groundwater-dependent ecosystems (i.e., areas with a relatively shallow water table that plays a major role in supporting vegetation health) is key to sustaining water resources in the western United States. Groundwater-dependent ecosystems (GDEs) in Colorado have non-pristine temporal and spatial patterns, compared to agro-ecosystems, which make it difficult to quantify how these ecosystems are impacted by changes in water availability. The goal of this study is to examine how key hydrosocial parameters perturb GDE water use in time and in space. The temporal approach tests for the additive impacts of precipitation, surface water discharge, surface water mass balance as a surrogate for surface–groundwater exchange, and groundwater depth on the monthly Landsat normalized difference vegetation index (NDVI). The spatial approach tests for the additive impacts of river confluences, canal augmentation, development, perennial tributary confluences, and farmland modification on temporally integrated NDVI. Model results show a temporal trend (monthly, 1984–2019) is identifiable along segments of the Arkansas River at resolutions finer than 10 km. The temporal impacts of river discharge correlate with riparian water use sooner in time compared to precipitation, but this result is spatially variable and dependent on the covariates tested. Spatially, areal segments of the Arkansas River that have confluences with perennial streams have increased cumulative vegetation density. Quantifying temporal and spatial dependencies between the sources and effects of GDEs could aid in preventing the loss of a vulnerable ecosystem to increased water demand, changing climate, and evolving irrigation methodologies.

Colorado

Characteristics of the fault damage zone From high-resolution seismic imaging along the Palos Verdes Fault, California

The distribution and intensity of fault damage zones provides insight into fault activity and its relationship to fluid flow in the crust. Presently, measures of the in-situ distribution of fault damage remain limited and along-strike studies are rare. This study focuses on an offshore section Palos Verdes Fault damage zone that spans 28 km, near Los Angeles, California. To investigate the previously unresolved shallow (∼400 m below the seafloor) fault damage zone we use densely spaced (∼500 m line separation) newly collected sparker multichannel seismic lines and sub-bottom profiles. The combination of high-resolution acquisition methods and specialized seismic processing workflows provide improved imaging of shallow faulting. We apply a multi-trace similarity technique to identify discontinuities in the seismic data that may be attributed to faults and fractures. This fault detection approach reveals diverse fault damage patterns on adjacent seismic profiles. However, a discernible damage zone pattern emerges by stacking multiple damage detection profiles along strike. We find that peak damage identified in this way corresponds to the active main fault strand, confirmed in this study, and thus the technique may be useful for identifying active fault strands elsewhere. Additionally, we observe that the variable width of the damage zone along strike is controlled by fault obliquity. Furthermore, our observations reveal a correlation between fault damage and seafloor fluid seeps visible in the water column, suggesting that damage plays a role in controlling fluid flow around the fault.

California

Estimating earthquake source depth using teleseismic broadband waveform modeling at the USGS National Earthquake Information Center

The U.S. Geologic Survey National Earthquake Information Center (NEIC) monitors global seismicity, producing a catalog of earthquake source parameters in near-real-time to provide information that can help mitigate the societal impact of earthquakes. The NEIC commonly relies on teleseismic observations to constrain earthquake source parameters (e.g., location, depth, magnitude, and mechanism) due to a lack of local and regional observations. For these ‘teleseismic’ events, depth phase (i.e., pP , sP ) arrival time observations provide the best estimate on source depth. However, depth phases are often difficult to accurately identify and/or pick. Therefore, NEIC relies on waveform modeling, such as those determined from W-phase ( M ww ), body wave ( M wb ), and regional ( M wr ) moment tensor estimations, to provide constraints on source depth. While depth estimates from these approaches are informative, higher frequency observations provide more precise estimates because depth phases are more prominently observed at higher frequencies. Here, we present NEIC’s relatively high-frequency (~0.04 to 1 Hz) teleseismic waveform modeling approach, termed Synthetic Depth Phase Modeling (SynDepth), for determining source depth. SynDepth was developed to provide NEIC with a tool that enables rapid, accurate, and quantifiable estimates of earthquake source depth in cases where locator depths are not reliable. This relatively simple and fast procedure searches over 1 km-incremented source depths and an expanding triangular source-time function to find the best-fitting solution. We compare automatic SynDepth solutions for a dataset of 1,216 earthquakes (M5.5-M7.6) between 2017 and 2021 to NEIC-derived depth estimates from other methods. Our approach provides a robust depth estimate for earthquakes lacking local arrival time data, and it minimizes the need for analyst review of depth-phase picks ( pP , sP ) or using predefined ‘fixed’ depths.

Seismological Research Letters

Onset of aftershocks: Constraints on the Rate-and-State model

Aftershock rates typically decay with time t after the mainshock according to the Omori–Utsu law, R (t)=K(c+t) −p ⁠ , with parameters K , c , and p . The rate‐and‐state (RS) model, which is currently the most popular physics‐based seismicity model, also predicts an Omori–Utsu decay with p = 1 and a c ‐value that depends on the size of the coseismic stress change. Because the mainshock‐induced stresses strongly vary in space, the c ‐value should vary accordingly. Short‐time aftershock incompleteness (STAI) in earthquake catalogs has prevented a detailed test of this prediction so far, but the newly developed a ‐positive method for reconstructing the true earthquake rate now allows its testing. Using previously published slip models, we calculate the coseismic stress changes for the six largest mainshocks in Southern California in recent decades and estimate the maximum shear as a scalar proxy of the coseismic stress tensor. Aftershock rates reconstructed for events in different stress ranges show that the rates follow a power law with p = 1 independent of stress with no clear sign of a c ‐value. The onset of the power‐law decay is abrupt and more delayed in areas with smaller stress changes. The observations do not necessarily contradict the RS model, as STAI limits the resolution for early aftershocks, and the RS model can reproduce the observations for specific Aσ values. However, the observations lead to strong constraints, namely Aσ <10 kPa and a power‐law decay of the background rate with distance to the fault, with exponent 2.7.

Seismological Research Letters

Critical minerals in mine waste

Introduction Critical minerals are commodities with vulnerable supply chains that play a vital role in supporting the United States’ economy, national defense and security, emerging technologies, and energy independence. The prosperity of our Nation depends on generating a resilient supply of domestic critical minerals; mine waste may be an untapped source of these commodities. Mine waste from centuries of legacy mining persist on the landscape and may contain critical minerals and other valuable commodities previously deemed uneconomic to recover. At modern mines, the financial viability of recovering byproduct critical minerals, which are not the primary target, may be marginal and can ultimately destine them to mine waste. Further, mine waste can be a liability for the mining company or, at legacy mines, the taxpayer because of its effect on the landscape. The U.S. Geological Survey (USGS) has several initiatives to evaluate critical mineral resources in various types of waste. This factsheet highlights studies of mine waste carried out by USGS scientists at the Geology, Energy & Minerals Science Center in collaboration with other science centers funded through the USGS Mineral Resources Program. Recovery of critical minerals from mine waste can aid in remediation efforts and increase domestic supply of vital mineral resources.

Fact Sheet

Deep groundwater total dissolved solids mapping in the Dakota Group, Williston Basin, USA

Growing concern about the quantity of available freshwater around the world has led to interest in surveying groundwater total dissolved solids (TDS) below water well depths. Deep TDS has not been systematically mapped, and there is much to learn about the distribution and controls on deeper groundwater. In sedimentary basins across the United States, groundwater resources often overlie hydrocarbon resources, providing an opportunity to use borehole geophysical data collected for hydrocarbons to characterize groundwater and pore space resources. This study adapts a recently developed subsurface geostatistical and geophysical modeling approach to continuously map groundwater TDS, porosity, and temperature in the Dakota Group of the Williston Basin—an undercharacterized regional aquifer system overlying deeper hydrocarbon reservoirs. Groundwater TDS in the Dakota Group ranges from approximately 4800 to 26,900 mg/L. TDS patterns are stratified with higher TDS in the lower and upper Dakota Group, and relatively lower TDS in the middle Dakota Group. The lower TDS in the middle zone may represent a preferential regional flow path for lower-TDS meteoric recharge from the west. The alternating pattern of TDS may also be evidence of higher-TDS inflows into the Dakota Group from underlying and potentially from overlying aquifers. Porosity is lower near the center of the Williston Basin and tends to be higher to the east, which may be related to grain size distributions. The new regional TDS and porosity modeling serves as a quantitative reference for water users and provides supporting evidence for hypotheses on Dakota Group recharge.

Montana, North Dakota, South Dakota

Substrate Enhancement Pilot Project—Monitoring summary and evaluation, Kootenai River, Idaho, 2012–22

To assess changes in substrate conditions and the efficacy of artificially placed substrates at select sites on the Kootenai River near Bonners Ferry, Idaho, the U.S. Geological Survey, in cooperation with the Kootenai Tribe of Idaho, completed repeat bathymetric, velocimetric, and underwater videography surveys. Collectively, three project sites throughout the Kootenai River make up the Substrate Enhancement Pilot Project (SEPP), an effort intended to improve spawning and egg incubation viability at locations identified to be aquatic habitat limited for the endangered Kootenai River white sturgeon (Acipenser transmontanus). Following the placement of coarse substrates at each site, bathymetric, velocimetric, and underwater videography data were collected from 2012 to 2022 to assess the role of deposition and erosion on maintaining suitable white sturgeon spawning and incubation substrates. Minimal erosion and deposition occurred at all Substrate Enhancement Pilot Project sites, according to interannual and intra-annual net volumetric changes between bathymetric surveys. Depending on the timing of bathymetric surveys relative to the annual peak streamflow conditions, isolated locations of deposition or erosion were observed at each site and the potential for deposition or erosion was supported by measured mean depth-averaged velocities. This study concluded that variability of deposition and scour were common at each site throughout the monitoring period and may be attributed to fluctuations in streamflow. Repeat bathymetric, underwater videography, and velocity mapping surveys were used to verify the interstitial spaces and surfaces of substrates at each SEPP site remained free of fine sediments for intervals longer than a year but were susceptible to deposition between high streamflow events.

Idaho

The geologic history of the Chehalis Forearc Basin, Washington State, USA

The Chehalis basin is located between the Cascade arc and the Coast Range in southwest Washington State. It consists of sedimentary and volcanic rocks deposited throughout the Cenozoic and is underlain by the Siletzia terrane, a thick, large igneous province accreted in the Eocene. Here, we constrain evolution of the Chehalis basin depocenter using isochore maps derived from isostatic gravity anomalies, borehole data, and stratigraphy for several time periods: the Eocene (47.6–36.8 Ma), the Oligocene (36.8–20 Ma), and the Neogene (20–0 Ma). Our results suggest that local subsidence is driven by deformation on faults that bound and intersect the basin. We see northward depocenter migration, interpreted as a shift in deformation from the northwest striking Cedar Creek fault to the west striking Doty fault. We interpret these data in terms of the long-term north-south shortening and clockwise rotation of the Cascadia forearc. During the Eocene, the Cedar Creek fault was preferentially aligned with north-south shortening, but became less active when clockwise rotation brought the Doty fault into east-west alignment with the stress field. Sediment accumulation rates decreased from 196 m/Myr in the Paleogene (∼40–20 Ma) to 27 m/Myr in the Neogene (∼20–0 Ma) as Miocene uplift of the Coast Range limited accommodation space and shifted the depositional environment from marine to fluvial. Our results are consistent with the geologic evolution of the Portland and Tualatin basins to the south and reveal a depositional and structural history uniquely shaped by clockwise rotation of the Cascadia forearc.

Washington

Potential warming-induced changes in stream water sources between proglacial and non-glacial streams, south-central Alaska

Snow and ice-melt are essential for global water resources. Rising air temperatures are causing vegetation encroachment and shrubification of previously snow- and ice-covered landscapes, and precipitation regimes are changing. Collectively, these changes will likely affect the hydrology of mountain environments, although the exact ways in which the hydrology will change are poorly understood. Changing source waters (i.e., the proportion of ice-melt, snowmelt, rain and groundwater) affect the timing and magnitude of streamflow and affect stream temperature, sediment, solute and nutrient fluxes. We investigate spatial and seasonal source water contributions across sub-watersheds of the Nellie Juan River watershed on Alaska's Kenai Peninsula, which differ in glacier cover, elevation and land cover, using a space-for-time approach. To do so, we use a three-endmember mixing model to quantify the contribution of rain, snow/ice-melt and deep groundwater. We show that snow/ice-melt peak later in proglacial streams compared to non-glacial streams. Endmember contributions in non-glacial streams generally vary with elevation and season. We also found that groundwater is a major contributor to streamflow across the study area, contributing between 12% and 47% seasonally, and may become increasingly important as snowpack and ice-melt decrease. This research characterises the shift from a glacierised to a deglaciating landscape through the lens of source water contribution. Broadly, these findings could help improve understanding of how water resources in glacierised watersheds are affected by warming air temperatures.

Alaska

Hydrologic investigations and a preliminary conceptual model of the groundwater system at North Penn Area 1 Superfund Site, Souderton, Montgomery County, Pennsylvania

The U.S. Geological Survey (USGS) conducted hydrogeologic investigations, reviewed existing data, and developed a preliminary conceptual model of the groundwater system as part of technical support of the U.S. Environmental Protection Agency (EPA) at the North Penn Area 1 Superfund Site (hereafter, the NP1 Site) located within the Borough of Souderton in Montgomery County, Pennsylvania. Field work and monitoring took place during 2012–18. The area is underlain by sedimentary formations that form a fractured-rock aquifer used for drinking water and industrial supply. The EPA placed the Site on the National Priorities List in 1989, identifying tetrachloroethylene (PCE) and trichloroethylene (TCE) as contaminants of concern. During 2012–18, the USGS conducted field activities that included drilling an 82-foot (ft)-deep monitoring well (MG 2220) in 2016, reconstructing a 208-ft-deep former industrial production well (MG 668 [Granite Knitting Mill]), and collecting borehole geophysical and video logs and water levels from those and five additional wells, which ranged in depth from about 50 to 200 ft below land surface. Continuous water levels were collected during 2014–17, and a synoptic set of water levels were measured in April 2018 in the seven wells. The borehole geophysical logs (caliper, acoustic televiewer, natural gamma, single-point resistance, vertical flow, and fluid temperature and resistivity) and borehole video logs in the seven wells were evaluated to assess potential for lithologic correlation and to identify and describe water-bearing features, which included both low- and high-angle fractures and other openings oriented along dipping bedding planes, joints, or possible faults. Borehole geophysical logs collected by USGS in 1992 in a 300-ft-deep former production well near the Site were also evaluated. Few to no distinctive features were identified on geophysical logs (natural gamma and single-point resistance) that could be used for correlation, thus limiting this approach to determining local geologic structure. Extensive fracturing in the upper 62 ft of monitoring well MG 2220 indicates that the well was likely drilled through a zone of faulting, and other evidence of faulting is present in the area near the Site. Assessment of continuous water levels showed hydraulic connections among some wells as indicated by rising or falling water levels in response to changes in pumping rates at nearby wells. A map of water levels measured in April 2018 indicates potential for groundwater flow generally toward the stream to the south and southwest of the Site, but the limited water-level data are insufficient to describe vertical groundwater gradients or lateral gradients in any detail. Review of 1999–2022 volatile organic compound (VOC) monitoring data collected by the Pennsylvania Department of Environmental Protection for five monitoring wells indicates that the highest groundwater concentrations of PCE and TCE were found in samples from extraction well MG 2201 (S-1) downgradient from, and nearest to, the previously identified Site contaminant source area, and these concentrations fluctuated through time. PCE concentrations were higher than TCE concentrations in samples from all five monitoring wells and were much higher than TCE concentrations in samples from extraction well MG 2201 (S-1). Temporally variable recharge is a possible factor affecting observed fluctuations in PCE concentrations in groundwater samples from well extraction MG 2201 (S-1), as indicated by a general inverse relation between PCE concentrations and water levels in a nearby long-term observation well. The PCE concentration of 1,830 micrograms per liter (μg/L) in a May 2018 water sample from monitoring well MG 2220 was more than four times the PCE concentration of 444 μg/L in a December 2017 sample from the nearby extraction well MG 2201 (S-1), which is open to fewer fractures. Low concentrations of VOCs were measured in surface water at two stream sites downgradient from wells with the highest groundwater VOC concentrations at the Site, indicating that discharge of contaminated groundwater to the stream is likely. Development of a conceptual model of the groundwater system was constrained by limited data. In areas with no pumping, groundwater-flow directions generally are thought to be controlled by topography and geologic structure (bedding orientation) and likely to the south and southwest of the Site, with local flow directions affected by orientations of fractures, joints, and local faults. Additional investigations that could help improve the conceptual model of the groundwater system and help delineate the extent of groundwater contamination and its transport are discussed.

Pennsylvania

Induced earthquakes are generally not tidally triggered in Oklahoma and Kansas

Human-induced earthquakes occur along critically stressed faults as injected wastewater simultaneously heightens fluid pressure and pushes faults to failure. We investigate the possibility that small stresses imposed by Earth tides could trigger earthquakes in the induced seismicity region of Oklahoma and Kansas from 2011 to 2018. We decluster a catalog consisting of ∼110,000 earthquakes using three methods (Reasenberg, nearest-neighbor distance, and phase-bin). We find no significant tidal earthquake triggering using Schuster's p -value test for the declustered catalogs as a whole. We search for localized triggering using discretized space-time cells and find ∼0–6% of cells have significant tidal triggering which is close to what is randomly expected (5%) and indicates there is an insignificant amount of tidal triggering for the full study region. One area that has significant p -values across multiple time windows, ∼2014–2016 is ∼15 km from a region of large wastewater injection volume. It is possible that localized tidal triggering occurs for this time and area because faults remain critically stressed and are particularly susceptible to slip under the small stress load from the semidiurnal tide. Possible explanations for the lack of tidal triggering in our broader study are that the pre-seismic stressing rate in the earthquake nucleation area is faster than the tidal stressing rate (∼3 kPa/day), faults are not close enough to critically stressed to be affected by tidal forcing, and that nucleation occurs over longer periods than the tides considered in this study (∼1, ∼14 days). Fluid injection could be the source of a higher pre-seismic stress rate.

Kansas, Oklahoma

Estimation of the accessible and useful resource base for electric-grade enhanced geothermal systems (EGS) resources of the Great Basin, USA

Scientists with the U.S. Geological Survey (USGS) recently completed a provisional assessment of the electric-grade geothermal resources associated with the low-permeability geologic formations of the Great Basin, USA, where resources are assumed to be accessible using enhanced geothermal systems (EGS) technologies (i.e., the engineering of sufficient permeability to facilitate efficient heat extraction). This assessment required estimation of the accessible resource base (electric-grade heat [>90ºC] at depths where drilling and stimulation are deemed achievable using current technology) and useful resource (heat that can be extracted from the accessible region). Electric-grade heat can be estimated from existing temperature models. The accessible resource base can be estimated as the electric-grade heat that exists at depths shallower than 6 km based on the limitations of current drilling and stimulation technologies, along with evidence for sustained natural fracture conductivity at depth. The useful part of the accessible heat can be estimated as the product of three efficiencies and factors: the heat extraction efficiency, the viable geology factor, and the reservoir spacing efficiency. The accessible and useful parts of the resource can be estimated in units of heat, or in units of electric power using an electrical conversion efficiency, which is a function of resource temperature. We also estimate the ranges for each of the efficiencies and describe the motivations behind the choice of best estimates used for the recent assessment. An analytic solution is provided for the useful resource above any depth (in units of electric power), where efficiency estimation assumes nearly steady heat extraction rates that cool reservoirs to 90ºC over 30 years of power generation.

Great Basin

Beyond optimality: Dryland ecosystems infrequently use water efficiently for carbon gain

Optimality theory assumes plants maximize carbon gain per unit water lost and is often implemented to scale leaf-level carbon gain and water use to regional and global scales. Optimality theory is often mathematically represented by assuming plant water-use efficiency (WUE) scales with VPD k , where k = ½ represents expected optimal behavior. It is unclear, however, if this relationship holds in arid and semi-arid ecosystems that are strongly impacted by soil and atmospheric moisture status. We used data from seven flux tower sites along an aridity gradient in New Mexico to answer: how does the relationship between WUE and VPD compare to expectations based on optimality theory? To address this question, we integrated the Dynamic Evapotranspiration Partitioning Approach for Rapid Timescales with a stochastic antecedent model to estimate ecosystem-level WUE (GPP/T) and the net sensitivity of WUE to VPD, or k Dynamic , which we compare to the theoretical optimal sensitivity of k = ½. Our results show that optimality theory is not always appropriate, and k Dynamic often deviates from ½, especially at some of the more arid sites or during periods of low soil moisture. At less arid, higher elevation sites, k Dynamic is most consistent with optimality theory at moderate VPD levels, but not at high VPD. In general, the sensitivity of WUE to VPD is highly variable such that k Dynamic exhibits notable daily and seasonal variability, suggesting highly dynamic stomatal behavior. These results emphasize that representing plant water-use strategies as dynamic in time and space is critical to improving large-scale estimates of plant water use.

New Mexico

New methodology for assessing underground natural gas storage resources – Example from Michigan Basin, United States

Energy consumption in the United States (U.S.) and across the world is shifting away from traditional fossil fuels like coal and oil, and towards natural gas and renewable sources, including hydrogen. Because gas demand is typically greatest during cold seasons and renewable sources sometimes produce variable supplies, it is important to store energy for use when demand exceeds supply. Whereas batteries and tanks typically store energy above ground, geologic (underground) storage may be able to retain much greater quantities of energy over much longer durations (e.g., Matos et al. 2019; Buursink et al. 2023). Consequently, the U.S. Geological Survey (USGS) is developing a methodology to locate new geologic energy storage sites with an initial focus on depleted hydrocarbon reservoirs followed by estimates of associated pore space or gas storage capacity. Depleted hydrocarbon fields in Michigan Basin in the U.S. already host large quantities of injected natural gas (about 681 billion cubic feet of seasonal gas capacity in 42 gas storage facilities; U.S. Energy Information Administration 2024). Therefore, we used this basin as an example to assess potential new storage resources alongside existing storage capacity and carbon dioxide sequestration resources (e.g., Katz and Coats 1968; Haagsma et al. 2020). In Michigan Basin gas storage is taking place in reservoirs within several key hydrocarbon producing formations with different lithologies, including the informal Stray sandstone of the Michigan Formation and the pinnacle reefs of the Niagara Group (Gautier et al. 1995; Swezey et al. 2015). The assessment methodology introduced here consists of two steps relying on both well information and reservoir data.

Michigan

Prioritizing resource protection and understanding potential susceptibility of springs to surficial changes in a low-temperature geothermal system

Geothermal systems are vulnerable to changes in water budget and composition, requiring science-based management. This study uses a dataset of spring water temperatures, time series of groundwater residence time tracers (tritium and carbon-14), and stable isotopes of water to understand geothermal flow in a low-temperature geothermal system in north west Colorado, United States (Steamboat Springs). The geothermal system is bisected by the Yampa River, necessitating a stream mass balance approach to quantify total discharge. Time series analysis of water temperature data provides a ranked list of features more susceptible to surficial changes, which is corroborated using time series of tritium which indicate spatially distinct patterns of mixing between modern and pre-modern groundwater. All springs contain a portion of pre-modern groundwater that is thousands to tens of thousands of years old, a period coinciding with melting of extensive Pleistocene glaciers that was likely one of the recharge sources to the geothermal system. Stream mass balance indicates that greater than 80% of the total geothermal discharge is derived from diffuse or small springs, highlighting the extensive nature of the geothermal outflow zone and the association with local geologic structures. This study provides baseline data to support management of the Steamboat Springs geothermal system and indicates the utility of these approaches in developing science-based geothermal management.

Colorado