Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Journal of the Nevada Water Resources Association”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,691 records · Page 15Linked to original sources
USGS2025

Confocal laser-scanning microscopy (CLSM)-based thermal maturity of Tasmanites and progress in standardization of fluorescence microspectrometry

Evaluation of thermal maturity in vitrinite-free or vitrinite-deficient sediments via fluorescence microspectrometry can provide relevant information related to petroleum exploration and thermal history assessment. However, variation in spectral fluorescence properties of alginite macerals with increasing thermal maturity is largely underexplored. Here, authors of this study have applied confocal laser-scanning microscopy (CLSM) in conjunction with fluorescence microspectrometry to a maturity series of marine Upper Devonian Tasmanites algae from the Ohio Shale (Huron Member) and a single sample from the Marcellus Formation of the Appalachian Basin. Spectral fluorescence properties of Tasmanites were evaluated in relation to orientation, measurement location, and the number of measurements per sample, and were compared to published literature. Emission spectra of Tasmanites from continuous wave laser excitation (405 nm) were acquired from sections perpendicular and parallel to bedding and at different positions within individual Tasmanites bodies. The results showed a progressive red-shift in emission maxima (λ max ) in a large sample sized maturity series ( N = 19), e.g., 493 to 578 nm for the perpendicular section at middle position. Further, blue-shifted apex and mineral-adjacent positions within sections perpendicular to bedding were observed, with the latter being reported here for the first time. While blue-shift at apex positions can be attributed to mechanical deformation-induced reorientation of photoselected fluorophores, the blue-shifted mineral-adjacent positions could result from strain loading and development of a plastic deformation region at the mineral contact zone with Tasmanites . A decrease in standard deviation with increasing number of measured emission maxima is well-observed, and 15 to 20 individual measurements per sample appears sufficient for low standard deviation and coefficient of variance. CLSM-derived thermal maturity parameters indicated that a moderate positive correlation of red/green quotient (Q 650/500 ; R 2 = 0.67) with solid bitumen reflectance (BR o in %) exists. For reproducible results, the determination of λ max and Q 650/500 should be conducted exclusively in the middle position at perpendicular and parallel sections of the polished whole-rock pellets, where the lowest standard deviation in measurement was observed. These results strengthen the suitability and relevance of the CLSM technique in thermal maturity studies of dispersed organic matter (DOM) and contribute to the standardization of fluorescence microspectrometry methods in organic petrology investigation.

Kentucky, Ohio, Virginia, West Virginia↗
USGS2025

Quality of groundwater used for domestic supply in the Gilroy-Hollister basin and surrounding areas, California, 2022

More than 2 million Californians rely on groundwater from domestic wells for drinking-water supply. This report summarizes a 2022 California Groundwater Ambient Monitoring and Assessment Priority Basin Project (GAMA-PBP) water-quality survey of 33 domestic and small-system drinking-water supply wells in the Gilroy-Hollister Valley groundwater basin and the surrounding areas, where more than 20,000 residents are estimated to utilize privately owned domestic wells. The study area includes the Llagas subbasin in the north, the North San Benito subbasin in the south, and the surrounding uplands. The study was focused on groundwater resources used for domestic drinking-water supply, which are mostly drawn from shallower parts of aquifer systems rather than those of groundwater resources used for public drinking-water supply in the same area. This assessment characterized the quality of ambient groundwater in the aquifer before filtration or treatment, rather than the quality of drinking water delivered to the tap. To provide context, the measured concentrations of constituents in groundwater were compared to Federal and California State regulatory and non-regulatory benchmarks for drinking-water quality. A grid-based method was used to estimate the areal proportions of groundwater resources used for domestic drinking wells that have water-quality constituents present at high concentrations (above the benchmark), moderate concentrations (between one-half of the benchmark and the benchmark for inorganic constituents, or between one-tenth of the benchmark and the benchmark for organic constituents), and low concentrations (less than one-half or one-tenth the benchmark for inorganic and organic constituents, respectively). This method provides statistically representative results at the study-area scale and permits comparisons to other GAMA-PBP study areas. In the study area, inorganic constituents in groundwater were greater than regulatory benchmarks (U.S. Environmental Protection Agency [EPA] or State of California maximum contaminant levels [MCLs]) for public drinking-water quality in 24 percent of domestic groundwater resources. The inorganic constituents present at concentrations greater than MCLs for drinking water were nitrate (as nitrogen), barium, chromium, and selenium. Total dissolved solids (TDS) or manganese were present at concentrations greater than the secondary maximum contaminant levels (SMCLs) that the State of California uses as aesthetic-based benchmarks in 48 percent of domestic groundwater resources. No volatile organic compounds or pesticide constituents were present at concentrations greater than regulatory benchmarks. Total coliform bacteria and enterococci were detected in 4 percent of domestic groundwater resources. Per- and polyfluoroalkyl substances (PFAS) were detected in 19 percent of domestic groundwater resources, and 10 percent had concentrations greater than recently enacted (April 2024) EPA MCLs. Physical and chemical factors from natural and anthropogenic sources that could affect the groundwater quality were evaluated using results from statistical testing of associations between constituent concentrations and potential explanatory variables. In this study, relevant physical factors include well construction characteristics, groundwater age, site proximity to groundwater recharge or discharge zones, and potential sources of contamination. Relevant chemical factors include the initial chemistry of the recharge water, the mineralogy of the aquifer sediments, and the subsequent shifts in chemistry as biologic and geologic reactions alter groundwater in the subsurface. Nitrate concentrations were correlated to agricultural land use, distance from the boundary of the Gilroy-Hollister Valley groundwater basin, and the proportion of modern (post-1950s) water captured by the well. Denitrification under anoxic redox conditions can mitigate some nitrate derived from fertilizer application. Total dissolved solids primarily were derived from water-rock interactions with soils and aquifer materials in the study area, but there were high concentrations where agricultural practices contributed additional TDS. Mineralogy of aquifer sediments and rocks also affect barium, selenium, boron, and chromium concentrations in the Gilroy-Hollister Valley groundwater basin. PFAS were positively correlated with urban land use and the proportion of modern water captured by the well.

California↗
USGS2025

Estimating the probability of export restrictions to inform mineral criticality

To assess risks associated with advanced technologies’ supply chain disruptions, governmental agencies and others have developed mineral “criticality” assessments, with criticality described using the economic impact and probability of supply chain disruptions. Previous work developed subjective supply risk indicators to approximate this probability, typically combining several factors such as supply diversity and trading partners’ political stability, where indicator weightings can substantially impact results. This work explicitly quantifies export barrier probability using an ensemble of machine learning classifiers, with probability estimates informed by exogenous variables, including prior barrier implementation and global export dominance. Major differences in high-probability countries and commodities are observed across models, but the ensemble method highlights Indonesia, China, Tanzania, and the United States as particularly high risk. The Supplementary Data File provides export barrier probability estimates for each analyzed country-commodity pair, enabling a direct, quantitative, objective contribution to assessing mineral criticality, enhancing risk identification and prioritization for policymakers.

Resources, Conservation, and Recycling↗
USGS2025

Alteration mapping in granitic gneiss using handheld geophysical and geochemical instruments: Implications for iron oxide-apatite and rare earth elements exploration

The Adirondack Mountains of New York, U.S.A. contain iron oxide-apatite (IOA) mineral deposits with variable concentrations of rare earth elements (REE). The IOA mineral deposits are typically hosted in the Lyon Mountain Granite Gneiss and are spatially correlated with extensive Na metasomatism (albitization) of the surrounding country rocks, although some mineral deposits also occur in metagabbro, paragneiss, and anorthosite hosts. The location of albitization zones is key to finding new IOA mineral deposits and better understanding the mineralization processes associated with their genesis. However, the Na alteration zones are generally not visibly identifiable in outcrop or hand specimens because the color and textural changes are subtle and are thus difficult to map. Here, we discuss the results from testing two spectroscopic techniques (handheld, field gamma-ray spectroscopy, and portable X-ray fluorescence (pXRF)) to characterize albitization zones surrounding IOA mineral deposits. The gamma-ray and pXRF spectrometers successfully distinguished the relative intensity of alteration in the Lyon Mountain Granite Gneiss based on the K abundance. The measured K content decreases towards the IOA mineral deposits, and the magnitude and width of the gradient are similar along the strike of each mineral deposit. Elevated Th and U values are present in host rocks adjacent to REE-bearing IOA mineral deposits. The pXRF and gamma-ray spectrometer K values are remarkably consistent with laboratory-based, whole-rock XRF compositional data and, therefore, useful for semi-quantitative analysis. Notably, albitization aureoles are consistent around REE-rich and REE-poor mineral deposits, suggesting that saline fluids are essential for the petrogenesis of IOA mineral deposits but may not be critical to REE mineralization. Ultimately, this study demonstrates the utility of handheld gamma-ray and pXRF spectrometry for identifying otherwise cryptic albitization gradients associated with IOA mineral deposits in granitic gneiss.

New York↗
USGS2026

Mineral chemistry perspective on remobilization of stored magma at Kamakai'a Hills, Southwest Rift Zone of Kilauea, Island of Hawai'i, USA

Differentiated magmas stored in the rift zones of Kīlauea have received more attention in recent years following eruption of andesite during the early phase of 2018 lower East Rift Zone activity. Despite this growing interest, some of the most voluminous eruptions of differentiated rift zone magmas remain poorly studied. One such eruption, and the most voluminous exposed differentiated flow field at Kīlauea, is the Kamakaiʻa Hills. This eruption took place in the Southwest Rift Zone of Kīlauea, a region that is hypothesized to contain a long-lived rift zone reservoir. The Kamakaiʻa Hills flow field encompasses >250 × 10 6 m 3 of basaltic andesite and basalt compositions with a mineral assemblage of orthopyroxene + clinopyroxene + plagioclase during its early ʻaʻā phase and clinopyroxene + plagioclase + olivine during its late pāhoehoe phase. To better understand storage conditions and magma accumulation, this study focuses on major, minor, and trace elements from the mineral assemblage present within the early ʻaʻā and late pāhoehoe phases. The diversity of clinopyroxene and plagioclase compositions within the early ʻaʻā and late pāhoehoe phases, as well as diverse compositions of plagioclase and orthopyroxene within the early ʻaʻā phase, suggest multiple magma bodies and limited pre-eruption magma mixing within the broader Kamakaiʻa Hills reservoir. Oscillatory zoning patterns (particularly in clinopyroxene) imply processes such as recharge events, magma mixing or mingling, or convection within a differentially cooling, chemically stratified reservoir over protracted time intervals, whereas only limited resorbed mineral textures indicate incomplete mixing of heat and chemically distinct magmas during the dike intrusion that triggered the eruption. Mineral-mineral and mineral-melt thermobarometry indicate predominantly shallow (≤2.5 km depth) crustal storage conditions of the cooled, differentiated magma (∼1100 °C and cooler for the basaltic andesites) to hotter temperatures for the basalts (all >1100 °C). Despite the known large standard errors estimated for mineral-melt and mineral-mineral barometry (10s to >100 MPa), the calculated pressures and depths broadly correspond with earthquake swarm depths beneath the Kamakaiʻa Hills, and drill core and fluid inclusion barometry storage depths of differentiated magmas within the lower East Rift Zone. The Kamakaiʻa Hills differentiated magmas have H 2 O contents (∼0.5 wt%, using plagioclase-melt hygrometry) equivalent to typical Kīlauea basalts. Our data and interpretations demonstrate a complex, long-lived rift zone storage system that consisted of multiple magma bodies and was mobilized into eruption through intrusion of a hotter and more primitive summit-derived (uprift) magma.

Hawaii↗
USGS2025

Component identification of solid biomass fuels using reflected light microscopy: Interlaboratory study 2

As nations transition toward sustainable energy systems , biomass has become a vital component of global energy portfolios. Derived from organic materials such as wood, agricultural residues, forestry byproducts, and organic waste, biomass is a renewable energy source with significant environmental and economic benefits. Responsible biomass energy production can improve waste management, reduce emissions of greenhouse gases, and mitigate environmental pollution. However, as the diversity of biomass-derived fuels increases, robust quality assessment methods are essential to ensure their efficiency, safety, and minimal environmental impact. Reflected light microscopy (RLM) is one such technique with the potential to complement conventional physico-chemical analyses by enabling a rapid identification of material constituents and impurities. To refine this methodology and evaluate the reproducibility of solid biomass component identification using RLM, an interlaboratory study (ILS) was conducted. The study involved the recognition of 58 components across 45 photomicrographs, with the participation of 65 scientists and students from 25 countries. The participants faced high difficulty identifying some of the marked components, and as a result, the percentage of correct answers ranged from 19.0 % to 98.3 %, with an average correct identification rate of 62.7 %. The most challenging aspects of the identification process included distinguishing between woody and non-woody (agro) biomass, accurately identifying petroleum-derived materials, and differentiating agro biomass from inorganic matter. The results suggest that while RLM is an important tool for characterizing solid biomass, further development of methodology guidelines and training are necessary to enhance its effectiveness. Future research should prioritize preparing detailed, image-rich, microscopic morphological descriptions of biomass fuel components, which could improve the accuracy and reliability of using RLM in biomass fuel characterization.

International Journal of Coal Geology↗
USGS2025

Estimation of the accessible and useful resource base for electric-grade enhanced geothermal systems (EGS) resources of the Great Basin, USA

Scientists with the U.S. Geological Survey (USGS) recently completed a provisional assessment of the electric-grade geothermal resources associated with the low-permeability geologic formations of the Great Basin, USA, where resources are assumed to be accessible using enhanced geothermal systems (EGS) technologies (i.e., the engineering of sufficient permeability to facilitate efficient heat extraction). This assessment required estimation of the accessible resource base (electric-grade heat [>90ºC] at depths where drilling and stimulation are deemed achievable using current technology) and useful resource (heat that can be extracted from the accessible region). Electric-grade heat can be estimated from existing temperature models. The accessible resource base can be estimated as the electric-grade heat that exists at depths shallower than 6 km based on the limitations of current drilling and stimulation technologies, along with evidence for sustained natural fracture conductivity at depth. The useful part of the accessible heat can be estimated as the product of three efficiencies and factors: the heat extraction efficiency, the viable geology factor, and the reservoir spacing efficiency. The accessible and useful parts of the resource can be estimated in units of heat, or in units of electric power using an electrical conversion efficiency, which is a function of resource temperature. We also estimate the ranges for each of the efficiencies and describe the motivations behind the choice of best estimates used for the recent assessment. An analytic solution is provided for the useful resource above any depth (in units of electric power), where efficiency estimation assumes nearly steady heat extraction rates that cool reservoirs to 90ºC over 30 years of power generation.

Great Basin↗
USGS2025

Emerging investigator series: Post-wildfire sediment geochemical characterization reveals manganese reactivity and a potential link to water quality impairment in the Gallinas Creek watershed, New Mexico

Water quality post-wildfire is often impaired by increased turbidity and elevated concentrations of elements such as manganese (Mn) and iron (Fe). Precipitation events exacerbate these issues, due in part to increased erosion and transport of sediment from hillslopes to surface water. Both Mn and Fe are major redox-active elements in sediments that drive a variety of biogeochemical cycles, precipitate adsorptive phases, and can themselves be drinking water contaminants. By investigating Mn and Fe sediment geochemistry in post-wildfire sediment deposits, related water quality hazards can be assessed. To establish and strengthen this connection, we analyzed the geochemistry of sediment deposits and surface water in the Gallinas Creek watershed, New Mexico over 1.5 years post-wildfire. Analyses included particle size analysis, water extractions, sequential extractions and aqua regia extractions to determine metal partitioning in sediment deposits. Data demonstrate Mn concentrations were distributed across labile and reactive fractions, such as the exchangeable and oxyhydroxide fractions, while Fe concentrations were mainly associated with the residual fraction. Manganese concentrations in aqua regia extractions and several fractions of sequential extractions were also strongly and significantly correlated with fine-grained sediment while the same pools of Fe concentrations were not. Dissolved Mn concentrations in surface water were elevated (>50 μg L −1 ) multiple times over the 1.5 years post-wildfire, highlighting a relationship between sediment geochemistry and water quality. This work shows Mn in sediments mobilized post-wildfire has an influence on water quality and highlights how further investigation into Mn sediment redox processes and mineralogy post-wildfire can inform risk assessments and resource management.

New Mexico↗
USGS2026

Effects of a low-lipid diet on the gut microbiome and head kidney transcriptome of juvenile Chinook Salmon

Objective Pacific salmon Oncorhynchus spp. reared in production hatcheries are typically fed high-lipid, energy-dense diets to achieve large size and high body condition prior to release. In contrast, juveniles in natural environments tend to consume low-lipid, high-protein diets, and fish reared for research or conservation purposes are sometimes fed diets that are formulated to mimic natural diets and promote wild-like phenotypes. Understanding how these alternative diets affect fish health beyond growth and body condition could ultimately contribute to improving hatchery fish fitness. Methods In this work, we evaluated changes in the fecal microbiome and gene expression of juvenile Chinook Salmon O. tshawytscha on a standard high-lipid hatchery diet versus a low-lipid diet formulated to mimic the nutrition profile of natural-origin fish. To evaluate the time scale at which diet alters the fecal microbiome, we collected longitudinal samples over a 12-week period and switched the diets of a subset of fish twice during the experiment. We used 16S ribosomal RNA gene amplicon sequencing to characterize fecal microbiome differences between fish on the two diets as well as hatchery-reared fish at a production hatchery, hatchery fish that had been captured after release into a stream, and natural-origin, stream-reared fish of similar ages. Additionally, we conducted RNA sequencing on head kidney samples from laboratory-reared fish to evaluate changes in gene expression in this important immune organ. Results We found that the low-lipid diet and the hatchery diet resulted in microbiomes that differed from the microbiome of natural-origin fish and from each other and that diet-driven changes to the microbiome could occur in under 14 d. The low-lipid diet did not result in a microbiome that resembled the microbiome of naturally produced fish. Instead, the low-lipid diet resulted in a microbiome community that was distinct from those of fish reared on the hatchery diet and fish sampled from the wild. The RNA sequencing results indicated differential enrichment of pathways related to immunity, metabolism, and hormone synthesis between fish that were fed the two experimental diets. Conclusions The results suggest that additional environmental factors influence the microbiome more strongly than diet formulation or that the low-lipid diet has a smaller effect on the microbiome than a natural, ­invertebrate-based diet. Given that the gut microbiome and systemic immune function contribute significantly to disease resistance, our findings highlight the importance of understanding how diets fed to fish in captivity may affect fish health beyond growth and body condition metrics.

Journal of Aquatic Animal Health↗
USGS1999

Streamflow, base flow, and ground-water recharge in the Housatonic River basin, western Massachusetts and parts of eastern New York and northwestern Connecticut

Streamflows for selected flow durations from 1 to 99 percent and the August median streamflows were estimated for 11 long-term streamflow-gaging stations in and near the study area. Estimates of streamflow and associated standard errors were determined for selected flow durations from 50 to 99 percent and the August median streamflows for 21 low-flow partial-record stations and for selected flow durations from 1 to 99 percent and the August median streamflows for two partial-record stations and seven short-term discontinued streamflow-gaging stations. Median streamflows per square mile for the 10-, 50-, and 90-percent flow durations and the August median streamflows were 3.90, 1.01, 0.185, and 0.248 cubic feet per second per square mile. Streamflows per square mile at selected flow-duration discharges between 1 and 99 percent at the 41 stations were related to basin characteristics to explain differences in streamflow characteristics. Basin characteristics included basin elevations, extent of stratified-drift deposits, land use, aspect, and underlying bedrock geology types. Most streamflow differences were positively correlated to basin elevation differences, most likely because precipitation increases with elevation, and to stratified-drift deposits, which allow more precipitation to recharge the ground water and to discharge later than do till and bedrock deposits. Mean base flow was computed from continuous records of daily mean discharge at 11 long-term streamflow-gaging stations in and near the study area. Mean annual base flow ranged from 13.4 to 24.5 inches per year. Minimum annual base flow ranged from 45 to 72 percent of mean annual rates at the 11 long-term stations, and the ratio of base flow to streamflow (base-flow index) ranged from 0.55 to 0.80. Base-flow durations between 1 and 99 percent were calculated from streamflow records at the 11 long-term streamflow-gaging stations. Base flow accounted for 45.5 to 85.0 percent of total annual streamflow at the 1- and 99-percent flow durations. Ground-water-recharge rates were computed from continuous records of daily mean discharge at 11 long-term streamflow-gaging stations in and near the study area. Mean annual ground-water-recharge rates ranged from 17.5 to 22.4 inches per year at 10 of the 11 long-term stations. Mean annual ground-water-recharge rates ranged from 2 to 7 inches per year higher than base flow. Minimum annual ground-water-recharge rates ranged from 48 to 72 percent of mean annual ground-water-recharge rates. Mean annual potential ground-water recharge was estimated from monthly climatological data collected at six climatological stations in and near the study area. Mean potential ground-water recharge ranged from about 17.9 to 28.9 inches per year, with a median value of 22.6 inches per year. This median value compares well to that calculated by use of streamflow records at the 11 streamflow-gaging stations (20.0 inches per year). Streamflows per square mile for the 10-, 50-, and 90-percent flow durations at stations in and near the study area were similar to those computed for other unregulated long-term continuous streamflow-gaging stations in central and eastern Massachusetts. Base-flow and ground-water-recharge rates in the study area compared closely to results from other studies in southeastern Massachusetts and Rhode Island, which were based on the same computational methods.

Connecticut, Massachusetts, New York↗
USGS2025

The role of alkali bicarbonate-sulfate brines in the genesis of carbonatite REE resources at the Bear Lodge Alkaline Complex, Wyoming

Rare-earth element (REE) resources in the Bear Lodge Alkaline Complex, Wyoming, are hosted in a variably leached carbonatite dike swarm spatially related to bodies of diatreme breccia. This study examines fluid inclusions in carbonatite dikes, peripheral fluorite breccias, and smoky quartz veins to reconstruct the physiochemical conditions of REE mineralization. Results reveal a multi-stage evolution of carbonatitic fluids: 1) high-temperature (330–432°C), CO 2 -rich magmatic fluids, 2) REE-enriched alkali bicarbonate-sulfate brines, and 3) low-temperature meteoric (117–182°C) or diluted magmatic fluids. Multiphase inclusions (stage-2) contain burbankite, nahcolite, and alkali sulfate daughter crystals, linking the brines to early burbankite [(Na,Ca) 3 (Sr,Ba,REE) 3 (CO 3 ) 5 ] mineralization in carbonatite. REE mobility has been linked to the stability of aqueous complexes with ligands such as Cl-, SO 4 2- , and HCO 3 - . However, light REEs were not initially transported significant distances, rather they crystallized as burbankite from brines or brine-melts associated with the carbonatite magma. Crystallization of burbankite removed Na from the system, leaving residual fluids with high K/Na ratios and promoting potassic fenitization throughout the complex. Fractionation of light and heavy REEs and involvement of low temperature (<300°C), high K/Na bicarbonate brines may have facilitated transport and formation of peripheral occurrences that are more enriched in heavy REEs at Bear Lodge.

Wyoming↗
USGS2024

Fish beta diversity associated with hydrologic and anthropogenic disturbance gradients in contrasting stream flow regimes

Understanding the role of hydrologic variation in structuring aquatic communities is crucial for successful conservation and sustainable management of native freshwater biodiversity. Partitioning beta diversity into the additive components of spatial turnover and nestedness can provide insight into the forces driving variability in fish assemblages across stream flow regimes. We examined stream fish beta diversity across hydrologic and anthropogenic disturbance gradients using long-term (1916–2016) site occurrence records ( n = 17,375) encompassing 252 species. We assessed total beta diversity (Sørensen dissimilarity), spatial turnover, and nestedness of fish assemblages in contrasting stream flow regimes across a gradient of decreasing flow stability: groundwater stable ( n = 77), groundwater ( n = 67), groundwater flashy ( n = 175), perennial runoff ( n = 141), runoff flashy ( n = 255), and intermittent ( n = 63) streams. Differences in total beta diversity among the stream flow regimes were driven predominantly (>86 %) by spatial turnover (i.e. species replacement) as opposed to nestedness (i.e. species loss or gain). Total fish beta diversity and spatial turnover were highest in streams with intermediate flow stability (groundwater flashy), while more flow-stable streams (groundwater stable and groundwater) had lower turnover and higher nestedness. Species turnover was also strongly associated with seasonal variation in hydrology across all flow regimes, but these relationships were most evident for assemblages in intermittent streams. Distance-based statistical comparisons showed significant correlations between beta diversity and anthropogenic disturbance variables, including dam density, dam storage volume and water withdrawals in catchments of groundwater stable streams, while hydrologic variables were more strongly correlated with beta diversity in streams with runoff-dominated and flashy flow regimes. The high spatial turnover of species implies that fish conservation actions would benefit from watershed-focused approaches targeting multiple streams with wide spatial distribution, as opposed to simply focusing on preserving sites with the greatest number of species.

Science of the Total Envionrment↗
USGS2025

Salinas Valley integrated hydrologic and reservoir operations models, Monterey and San Luis Obispo Counties, California

The area surrounding the Salinas Valley groundwater basin in Monterey and San Luis Obispo Counties of California is a highly productive agricultural area, contributes significantly to the local economy, and provides a substantial portion of vegetables and other agricultural commodities to the Nation. This region of California provides about half of the Nation’s lettuce, celery, broccoli, and spinach each year. Thus, this agricultural area provides significant volumes of agricultural products not just for California but the entire United States. Changes in population and increased agricultural development, which includes a shift toward more water-intensive crops, and climate variability, have put increasing demand on both surface water and groundwater resources in the valley. This has resulted in water management challenges in the Salinas Valley that are predominantly related to distribution of water supply throughout the basin. Where and when the water is present in the surface and subsurface does not coincide with where and when the water is needed. To deal with the distribution issue, historically water has been used conjunctively in the valley. Conjunctive use is a water management strategy that coordinates surface water and groundwater use to maximize water availability. Groundwater is used throughout the Salinas Valley to meet water demands when surface water supplies are insufficient. Availability of surface water is constrained by climate. Precipitation and streamflow vary seasonally and year to year. Although there are two reservoirs in the Salinas Valley to capture and store water during wet periods, the only conveyance of reservoir water to coastal agricultural areas is the Salinas River. Increasing demand on groundwater and surface water resources throughout the Salinas Valley has resulted in undesirable effects of unsustainable water use, such as surface water depletion, groundwater level declines, storage depletion in the principal aquifers, and seawater intrusion. To address these escalating issues, local communities, water management agencies, and groundwater sustainability agencies are evaluating how to sustainably manage both their surface water and groundwater resources. To meet water demands and reduce undesirable effects of unsustainable water use, continued conjunctive management of surface water and groundwater would ideally incorporate strategies to deal with increases in demand and a variable climate. To evaluate the challenging water management issues in the Salinas Valley, the U.S. Geological Survey, Monterey County Water Resource Agency, and the Salinas Valley Basin Groundwater Sustainability Agency developed a comprehensive suite of models that represent the Salinas Valley Hydrogeologic system called the Salinas Valley System Model. The Salinas Valley Geologic Framework was developed to characterize the subsurface using various topographic and geologic data sources, including information on hydrogeologic units, their surfaces and extents, geologic structures, lithology, and elevations from borehole data and cross sections, as well as details on faults and existing models. The Salinas Valley Watershed Model simulates the entire Salinas River watershed. Monthly surface water inflows into the integrated hydrologic model domain were simulated using the Salinas Valley Watershed Model. The historical model uses historical climate data, water and land use data, and reservoir releases to simulate agricultural operations, including landscape water demands, diversions, and reclaimed wastewater. The operational model adds an embedded reservoir operations framework to the simulation of the historical model that allows specified operational rules to simulate reservoir releases and changes in reservoir storage. The operational model assumes current reservoir operations and constant land use, which differs from historical conditions. Thus, the operational model is a hypothetical baseline model that can be used by local water managers to evaluate and quantify potential benefits of water supply projects. Together, the geologic framework, watershed, historical, and operational models form a tool that can be used to simulate irrigated agriculture and associated reservoir operations of the integrated hydrologic system of the Salinas Valley.

EarthArXiv↗
USGS2024

Using surficial geologic maps, vegetation, and monitoring to address erosion impacts from grazing in Channel Islands National Park, California

Employing a map-unit classification scheme based on geomorphic process and age, the U.S. Geological Survey (USGS) mapped Quaternary surficial deposits of the five islands comprising Channel Islands National Park (CHIS), California, as no such maps previously existed. Mapping was motivated through an agreement with the National Park Service (NPS) to aid natural resource assessments, including post-grazing disturbance recovery and identification of mass wasting and tectonic hazards. The resulting detailed (1:12,000 scale) maps portray areas of upland erosional transport processes and alluvial, fluvial, eolian, beach, marine terrace, mass wasting, and mixed depositional processes at a scale commensurate with the process signal on the landscape. Detailed, GPS-located observations of sedimentology, pedogenic development, landscape position, and geomorphology constrain map unit identification. In addition, map-unit boundary delineation was determined in a GIS using a variety of high-resolution (sub-meter) aerial imagery and lidar-based DEMs complemented by derivative raster products. The GIS geodatabase schema used is GeMS compliant. Resolvable map-unit widths are as small as 10-15 meter. Locational accuracy of unit boundaries is estimated to be as low as 10 m or better. Detailed mapping is at a scale allowing determination of geomorphic transport processes operating on the landscape and conveys geologic information to land managers at a resolution commensurate with park resources. Map unit ages are constrained by relative soil chronostratigraphy, vertebrate and invertebrate fossils, and materials collected for dating control using radiogenic, luminescence, and cosmogenic radionuclide techniques. Associated topical studies examined connections between geology, surface water, and vegetation distribution and restoration.

California↗
USGS2026

Salinas Valley integrated hydrologic and reservoir operations models, Monterey and San Luis Obispo Counties, California

The area surrounding the Salinas Valley groundwater basin in Monterey and San Luis Obispo Counties of California is a highly productive agricultural area, contributes substantially to the local economy, and provides a substantial portion of vegetables and other agricultural commodities to the Nation. This region of California provides about half of the Nation’s lettuce, celery, broccoli, and spinach each year. Thus, this agricultural area provides substantial volumes of agricultural products not just for California but for the United States. Changes in population and increased agricultural development, which includes a shift toward more water-intensive crops, and climate variability, have put increasing demand on both surface-water and groundwater resources in the valley. This situation has resulted in water management challenges in the Salinas Valley that generally relate to the distribution of the water supply throughout the basin. Where and when the water is present in the surface and subsurface does not coincide with where and when the water is needed. Historically, to deal with the distribution issue, water has been used conjunctively in the valley. Conjunctive use is a water management strategy that coordinates surface-water and groundwater use to maximize water availability. Groundwater is used throughout the Salinas Valley to meet water demands when surface-water supplies are insufficient. The availability of surface water is constrained by climate. Precipitation and streamflow vary seasonally and year to year. Although there are two reservoirs in the Salinas Valley to capture and store water during wet periods, the only conveyance of reservoir water to coastal agricultural areas is the Salinas River. Increasing demand for groundwater and surface-water resources throughout the Salinas Valley has resulted in undesirable effects from unsustainable water use, such as surface-water depletion, groundwater-level declines, storage depletion in the principal aquifers, and seawater intrusion. To address these escalating issues, local communities, water management agencies, and groundwater sustainability agencies are evaluating how to sustainably manage both their surface-water and groundwater resources. To meet water demands and reduce the undesirable effects of unsustainable water use, continued conjunctive management of surface water and groundwater would ideally incorporate strategies to deal with increases in demand and climate variability. To evaluate the challenging water management issues in the Salinas Valley, the U.S. Geological Survey, Monterey County Water Resources Agency, and the Salinas Valley Basin Groundwater Sustainability Agency developed a comprehensive suite of models that represent the Salinas Valley hydrogeologic system called the Salinas Valley System Model. The geologic framework is known as the Salinas Valley Geologic Framework and was developed to characterize the subsurface using various topographic and geologic data sources, including information on hydrogeologic units, their surfaces and extents, geologic structures, lithology, and elevations from borehole data and cross sections, as well as details on faults and existing models. The surface-water model is called the Salinas Valley Watershed Model and simulates the Salinas River watershed. Monthly surface-water inflows into the integrated hydrologic model domain were simulated using the Salinas Valley Watershed Model. The historical model uses historical climate data, water and land use data, and reservoir releases to simulate agricultural operations, including landscape water demands, diversions, and reclaimed wastewater. The operational model adds an embedded reservoir operations framework to the simulation of the historical model that allows specified operational rules to simulate reservoir releases and changes in reservoir storage. The operational model assumes current reservoir operations and constant land use, which differs from historical conditions. Thus, the operational model is a hypothetical baseline model that can be used by local water managers to evaluate and quantify potential benefits of water supply projects. Together, the geologic framework, watershed, historical, and operational models form a tool that can be used to simulate irrigated agriculture and associated reservoir operations of the integrated hydrologic system of the Salinas Valley.

California↗
USGS2024

New methodology for assessing underground natural gas storage resources – Example from Michigan Basin, United States

Energy consumption in the United States (U.S.) and across the world is shifting away from traditional fossil fuels like coal and oil, and towards natural gas and renewable sources, including hydrogen. Because gas demand is typically greatest during cold seasons and renewable sources sometimes produce variable supplies, it is important to store energy for use when demand exceeds supply. Whereas batteries and tanks typically store energy above ground, geologic (underground) storage may be able to retain much greater quantities of energy over much longer durations (e.g., Matos et al. 2019; Buursink et al. 2023). Consequently, the U.S. Geological Survey (USGS) is developing a methodology to locate new geologic energy storage sites with an initial focus on depleted hydrocarbon reservoirs followed by estimates of associated pore space or gas storage capacity. Depleted hydrocarbon fields in Michigan Basin in the U.S. already host large quantities of injected natural gas (about 681 billion cubic feet of seasonal gas capacity in 42 gas storage facilities; U.S. Energy Information Administration 2024). Therefore, we used this basin as an example to assess potential new storage resources alongside existing storage capacity and carbon dioxide sequestration resources (e.g., Katz and Coats 1968; Haagsma et al. 2020). In Michigan Basin gas storage is taking place in reservoirs within several key hydrocarbon producing formations with different lithologies, including the informal Stray sandstone of the Michigan Formation and the pinnacle reefs of the Niagara Group (Gautier et al. 1995; Swezey et al. 2015). The assessment methodology introduced here consists of two steps relying on both well information and reservoir data.

Michigan↗
USGS2024

Geologic map and structure sections along the southern part of the Bartlett Springs Fault Zone and adjacent areas from Cache Creek to Lake Berryessa, northern Coast Ranges, California

Introduction Located in the Coast Ranges of northern California, the Bartlett Springs Fault Zone is the easternmost fault in the San Andreas Fault system in northern California. The fault is a right-lateral, strike-slip structure considered capable of producing an earthquake of moment magnitude 7. The purpose of this mapping is to better characterize the geology and earthquake hazards associated with the southern part of the Bartlett Springs Fault Zone and to help identify any evidence of active uplift on the faults bounding the Coast Ranges. Although the area immediately surrounding the Bartlett Springs Fault Zone is sparsely populated, its southern segment presents a potential seismic hazard to northern California communities as far away as the San Francisco Bay region and Sacramento. There are also nearby water resources, mineral resources, and public lands used for public recreation. The Coast Ranges of northern California are a series of northwest-southeast-oriented mountain ranges and valleys located north of the San Francisco Bay region, between the Pacific Ocean to the west and the Sacramento Valley to the east. The region has rugged terrain, high mountain peaks that reach more than 2,400 meters above sea level, isolated and narrow valley bottoms on which most human settlements are located, and large drainage systems that tend to follow the northwest-southeast-oriented topographic grain. The physiographic character of the region is shaped by its bedrock geology, deformational history, and active faulting. The basement rocks of the northern Coast Ranges consist of the Franciscan Complex and the Great Valley complex, the latter of which consists of two informal units, the Coast Range ophiolite and the Great Valley sequence. The Franciscan Complex and the Great Valley complex are in structural contact along the Coast Range Fault, a regional-scale structure and fundamental crustal boundary. The Franciscan Complex and the Great Valley complex are superposed by active, northwest-southeast-striking strike-slip faults that are associated with seismicity swarms. These active strike-slip faults can produce moderate to large earthquakes that have moment magnitudes of 7–8. In places, these active structures bound large ranges and valleys, suggesting that much of the modern topographic expression is the result of active deformation processes. This report contains new 1:24,000-scale geologic mapping along the southern part of the Bartlett Springs Fault Zone between Clear Lake and Lake Berryessa. The map area spans 738 square kilometers in northern Napa County, southern Lake County, and parts of Yolo and Colusa Counties. The south and east borders of the map are 90 kilometers north of San Francisco and 70 kilometers west of Sacramento, respectively. The map area is within the Knoxville mining district, which has a history of mercury and gold mining dating back to the mid-19th century. The two main towns in the region, Lower Lake and Clearlake, California, are west-northwest of the map area. Approximately 71,000 people live in the cities and rural communities located within a 40-kilometer radius of the center of the map area. The bedrock geology, cross sections, and structural data presented herein are critical for evaluating the long-term evolution of the Bartlett Springs Fault Zone. This work will supplement studies on local seismic hazards, liquefaction potential, landslide hazards, earthquake geology, natural resources, groundwater resources, engineering geology, and tectonic history by providing the background information for site-specific investigations on these subjects.

California↗
USGS1990

Effects of storm-water runoff on local ground-water quality, Clarksville, Tennessee

Storm-related water-quality data were collected at a drainage-well site and at a spring site in Clarksville, Tennessee, to define the effects of storm-water runoff on the quality of ground water in the area. A dye-trace test verified the direct hydraulic connection between the drainage well and Mobley Spring. Samples of storm run off and spring flow were collected at these sites for nine storms during the period February to October 1988. Water samples were collected also from Mobley Spring and two other springs and two observation wells in the area during dry-weather conditions to assess the general quality of ground water in an urban karst terrain. Evaluation of the effect of storm-water runoff on the quality of local ground water is complicated by the presence of other sources of contaminants in the area Concentrations and load for most major constituents were much smaller in storm-water runoff at the drainage well than in the discharge of Mobley Spring, indicating that much of the chemical constituent load discharged from the spring comes from sources other than the drainage well. However, for some of the minor constituents associated with roadway runoff (arsenic, copper, lead, organic carbon, and oil and grease), the drainage well contributed relatively large amounts of these constituents to local ground water during storms. The close correlation between concentrations of total organic carbon and concentrations of most trace metals at the drainage-well and Mobley Spring sites indicates that these constituents are transported together. Many trace metals were flushed early during each runoff event. Mean storm loads for copper, lead, zinc, and four nutrient species (total nitrogen, ammonia nitrogen, total phosphorus, and orthophosphorus) in storm-water runoff at the drainage-well site were lower than mean storm load predicted from an existing regression model. The overprediction by the model may be a result of the small size of the drainage area relative to the range of drainage areas used in the development of the models, or to the below-normal amounts of rainfall during the period of sampling for this investigation. Loads& in storm-water runoff for 22 constituents were extrapolated from sampled storms to total loads for the period February to October 1988. Calculated loads for trace metals for the period ranged from 0.030pound.s for cadmium to 12pound.s for strontium. Loads of the primary nutrients ranged from 0.97pounds for nitrite as nitrogen to 34pounds of organic nitrogen. Storm-water quality at the drainage-well and Mobley Spring sites was compared to background water quality of the local aquifer; as characterized by dry-weather samples from three springs and two observation wells in the Clarksville area. Concentrations of total-recoverable cadmium, chromium, copper, lead, and nickel were higher in many stormwater samples from both the drainage-well and Mobley Spring sites than in samples from any other site. In addition, concentrations of total organic carbon, methylene blue active substances, and total-recoverable oil and grease were generally higher in storm-water samples from the drainage-well site than in any ground-water sample. Densities of fecal coliform and fecal streptococcus bacteria and concentrations of total recoverable iron, manganese, and methylene blue active substances in storm samples from the drainage-well site exceeded the maximum contaminant levels listed in Tennessee’s drinking-water standards (1988) by as much as 2,500 and 5,500 colonies per 100 milliliters, and 2.7, 0.29, and 0.05 milligrams per liter, respectively. Densities of fecal coliform and fecal streptococcus bacteria and concentrations of total-recoverable iron, manganese, and lead in storm samples from Mobley Spring exceeded the maximum contaminant levels by as much as 500 and 4,500 colonies per 100 milliliters, and 18.7,0.65, and 0.02 milligrams per liter, respectively. For iron, manganese, and bacteria, these undesirable levels are not necessarily attributable to storm-water recharge, because concentrations of these constituents also exceeded drinking-water standards in one or more of the dry-weather samples from selected springs and observation wells in the area.

Tennessee↗