Geology Reports⌕ Search

SEARCH · Geology Reports

Results for “Scientific Investigations Map”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

862 records · Page 13Linked to original sources
USGS2024

Numerical model of the groundwater-flow system near the southeastern part of Puget Sound, Washington

Groundwater flow in the active model area (AMA) was simulated using a groundwater-flow model. A steady-state model version of the model simulates equilibrium conditions, and a transient model version simulates monthly variability. The model corresponds to the physical and temporal dimensions of the conceptual model and groundwater budget. The steady-state model version represents average conditions for an 11-year period (January 1, 2005–December 31, 2015), and the transient model represents monthly hydrologic variability within that period. The 13-layer model was constructed using MODFLOW-NWT with a uniformly spaced grid consisting of 416 rows, 433 columns, and cells with a horizontal dimension of 500 feet (ft) on a side. The model was calibrated to measured values of water levels in wells and lakes and estimated base flow for selected streamflow measurement stations, commonly referred to as streamgages. Model calibration was accomplished using a combination of manual and automatic methods, including the Model-Independent Parameter Estimation (PEST) program that adjusted model input parameters with the aim of minimizing the difference between estimated and model-simulated values of hydraulic head and base flow. Model boundary conditions consist of all simulated groundwater inflow to and outflow from the AMA. For example, a stream reach that simulates a gain from or loss to groundwater is a boundary condition that allows water to exit or enter, respectively, the groundwater system. Other boundary conditions include springs, seeps, precipitation recharge, groundwater exchange with lakes and Puget Sound, and groundwater pumping. A comparison of the estimated groundwater budget to that simulated by the steady-state model version indicates that the relative percentages of total inflow or total outflow for six major categories of boundary conditions are similar for the two budgets. The model was used to simulate three suites of scenarios of potential drought and water-use changes. Scenario 1 suite consisted of the steady-state model version that was run with 0, 15, 20, and 25 percent reduction of precipitation recharge to assess the corresponding reductions in base flow with decreasing recharge. The last simulation for the scenario 1 suite consisted of the transient model version simulating 3 years of consecutive seasonal drought, defined by the months of May through September, to assess the corresponding base-flow reductions. Scenario 2 suite consisted of the steady-state model version with all simulated groundwater use removed, compared with a simulation that includes current groundwater use to evaluate changes to potentiometric surfaces and base flows. Scenario 3 suite consisted of a transient model version of the model that simulated pumping increases for four different categories of water-supply wells (compared to no pumping increases) to evaluate resulting reductions in base flow. Although, these scenarios provide examples of model applications and useful insights, many other scenarios could be simulated. A description of how to download the model is described in the body of this report. Uncertainty is associated with most model inputs. Groundwater levels, lake levels, and land-surface altitudes are relatively certain; other model inputs are far less certain, including precipitation recharge, base flow, hydraulic properties, water use, and the three-dimensional structure of subsurface hydrogeologic units. Models are useful not because of high levels of accuracy of all model inputs, but because they combine the best information and estimates available, thereby providing the best predictions available related to physical processes. The model described in this report simulates groundwater flow on a regional scale, which has inherent limitations for simulating hydrologic scenarios at local scales. Model structures and inputs were generalized to be consistent with this regional scale. For example, the actual groundwater system has much greater heterogeneity of hydraulic conductivity than is possible within the model’s degrees of freedom. Variations in hydraulic gradients over distances less than 500 ft cannot be simulated. The distances between model features, such as a pumping well and a stream, must be placed at 500-ft intervals and are co-located if both features are within the same model cell.

Washington↗
USGS2024

Volcanic gas monitoring

Introduction As magma rises through the crust, decreasing pressure conditions allow volatiles to exsolve from the magma. These volatiles then migrate upward through the crust, where they can be stored at shallower levels or escape to the atmosphere. Rising magma also heats rock masses beneath volcanic centers, causing water in shallow aquifers and hydrothermal systems to boil and release additional gases and steam (see chapter F , this volume; Ingebritsen and Hurwitz, 2024). The chemistry and quantity of gases that reach the surface during periods of quiescence or volcanic unrest can reveal that gas-rich magma is ascending, crystallizing, or alternatively stalling, with important implications for volcanic hazard (for example, Sutton and others, 1992; Aiuppa and others, 2007, 2021; Werner and others, 2009, 2011, 2012; Moretti and others, 2013; de Moor and others, 2016; Lewicki and others, 2019; Edmonds and others, 2022; Kern and others, 2022; Kunrat and others, 2022). Most volcanoes in Alaska and the western United States are characterized by weak degassing, with one or more low-temperature fumaroles (typically near the local boiling temperature of water) and connect to a deeper and sometimes extensive hydrothermal system (for example, McGee and others, 2001; Symonds and others, 2003a, b). Hydrothermal systems will affect the chemistry of rising gases exsolved from deeper magma (Symonds and others, 2001), including sulfur dioxide (SO 2 ), hydrogen chloride (HCl), and water vapor (for example, Doukas and Gerlach, 1995; Gerlach and others, 1998, 2008; Symonds and others, 2001; Werner and others, 2013). As an example, depending on factors such as temperature, pressure, and oxidation state, rising SO 2 will react with groundwater to form hydrogen sulfide (H 2 S) gas, dissolved sulfate (SO 4 2− ), or elemental sulfur (Christenson, 2000; Symonds and others, 2001; Werner and others, 2008). The reaction and dissolution of SO 2 into shallow groundwater is commonly referred to as scrubbing, and can reduce the likelihood that ascending, degassing magma can be detected. Carbon dioxide, however, in addition to exsolving from magma early in the ascent process, is not easily removed by hydrothermal fluids (Lowenstern, 2001). As scrubbing and other processes take place, the SO 2 /H 2 S, CO 2 /SO 2 , and CO 2 /H 2 S ratios may change. High rates of SO 2 emission indicate that magma has moved to relatively shallow levels in the volcano and that the system has heated up enough to establish dry pathways from depth to the surface. Monitoring multiple gas species and the total output of those species is thereby useful for volcano monitoring during both periods of quiescence, to establish background degassing conditions, and during unrest, when gas geochemistry and emission rates can provide information on changing conditions, such as magma ascent. To provide context for multidisciplinary volcano forecasts, we focus on the following two key required capabilities: (1) characterizing baseline geochemistry and gas discharge from volcanoes and volcanic regions and (2) monitoring changes in gas geochemistry and discharge to inform forecasts of volcanic eruptions and their effects. Sufficient baseline data must be collected to identify and interpret anomalous degassing associated with volcanic unrest (for example, Sorey and others, 1998; Rouwet and others, 2014). Differences in volcano type, baseline degassing rates, local hydrology, and geography (for example, high versus low latitude) will result in a different baseline for each volcano. Volcanoes of any threat level that exhibit one or more degassing phenomena would ideally be monitored by techniques needed to establish baseline degassing data, with the sampling frequency of baseline data dictated by the threat level (table E1). Additional monitoring techniques become necessary during periods of unrest. In general, three of the most important techniques for gas monitoring are (1) direct sampling of fumarole, spring, and soil gases for laboratory geochemical measurements, (2) measurements of the chemical composition of the volcanic plume and emission rates of major gas species (for example, H 2 O, CO 2 , SO 2 , and H 2 S) by satellite, airborne, or ground-based techniques, and (3) measurements of diffuse emissions of CO 2 and other gases through soils. Various methods and instruments may be useful both for baseline studies and during unrest.

Scientific Investigations Report↗
USGS2025

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗
USGS2024

Simulation of groundwater flow in the Long Island, New York regional aquifer system for pumping and recharge conditions from 1900 to 2019

The U.S. Geological Survey has developed a transient, groundwater-flow model that simulates hydrologic conditions in the Long Island aquifer system as part of an ongoing (since 2016) multiyear, cooperative investigation with the New York State Department of Environmental Conservation. The goals of this investigation are to assist stakeholders and resource managers to evaluate the response of the hydrologic system to changes in future hydraulic stresses. Responses in the hydrologic system include changes in water levels in the hydrogeologic units; discharge to streams, coastal waters, and subsurface infrastructure; and the extent of saline groundwater in the aquifers. Hydraulic stresses include future water-supply management and changes in land use and infrastructure. The numerical model synthesizes a diverse set of physiographic, geologic, climatic, land-use, and historical population, water use, and infrastructure data to physically represent the Long Island aquifer system from land surface to bedrock and to simulate annual hydrologic conditions between 1900 and 2019. A three-dimensional hydrogeologic framework was developed from existing and recently collected borehole geologic and geophysical data collected as part of a companion drilling program. Water-transmitting properties of the principal aquifer sediments were defined in three dimensions from new and existing lithologic logs. The distribution of recharge from precipitation was estimated from landscape characteristics and climate data. Anthropogenic recharge from wastewater, leaky infrastructure, and storm runoff were estimated from population, infrastructure, and pumping data. Water-use data, including well locations, depths, and pumping rates, were obtained from historical sources and records and used to estimate pumping stresses continuously in time and space, at an annual average time scale. The data were incorporated into a three-dimensional numerical model using the U.S. Geological Survey finite difference modeling code MODFLOW 6; the model encompassed all of Long Island and surrounding surface waters and simulated historical hydrologic conditions from 1900 to 2019. The calibration process involved trial and error adjustments using prior knowledge to improve general fit to observations followed by an inverse calibration to update and optimize input parameters, using an iterative ensemble smoother algorithm implemented in PEST++ version 5.0. This resulted in a model that generally was in good agreement with observed, dynamically varying hydrologic conditions from 1900 to 2019. The calibrated model was used to develop two base-case models for scenario testing of future, hypothetical conditions where one represented average-annual conditions, and one represented average-seasonal conditions from 2010 to 2019. The model representing average-annual conditions was modified further to represent an alternate sea-level position of 6 feet above the North American Vertical Datum of 1988, and the model representing average-seasonal conditions was modified to represent the average seasonal effects of a 5-year drought imposed upon current hydrologic conditions. Recharge is the sole source of water to the aquifer system; groundwater discharges to coastal water and streams and is withdrawn by pumped wells. Model-estimated annual recharge ranged from about 11 inches in 1965 to 41 inches in 1983. On average, from 2010 to 2019, about 23 percent of water was pumped from wells, and about 47 and 27 percent discharged to coastal waters and streams, respectively; the remaining 4 percent was water that moved into storage in the aquifer matrix. Water levels on Long Island vary naturally during time in response to changes in recharge; the amount of variation is largest in the interior of the island, in areas with highest water table altitudes near groundwater divides and lowest near streams and the coastal waters. The total range of water table altitudes on Long Island between 1900 and 2019 ranged from near 0 to more than 70 feet in western parts of Long Island. The largest range in altitudes is in New York City and is associated with areas of large historical withdrawals between the 1920s and the late 1980s. Water table altitudes generally varied by less than 10 feet in eastern Suffolk County, where the aquifer is under more natural conditions. Saltwater intrusion is of great concern on Long Island, particularly in western Long Island where both the unconfined and confined parts of the aquifer system have been intruded in response to large-scale groundwater withdrawals; however, the volume of freshwater in the islandwide aquifer system only has changed by about 5 percent between 1900 and 2019. The decadal change in the freshwater volume was largest during the early and mid-20th century, corresponding to the largest historical pumping, but that volume change did not exceed 1 percent. The negligible change in freshwater volume suggests that saltwater intrusion as of 2019 was limited at an islandwide scale but continues to occur in local areas of Queens and Nassau Counties, adversely affecting current water supplies and limiting future water supplies for affected communities. The regional groundwater model developed for this investigation is a tool that can be used to help determine the viability of current and future water supplies at a regional scale and can be used to support development of additional models at finer scale to support more focused assessments of groundwater sustainability.

New York↗
USGS2024

Simulated mean monthly groundwater-transported nitrogen loads in watersheds on the north shore of Long Island Sound, 1993–2022

Elevated nitrogen loads are pervasive in the Long Island Sound, an estuary that receives freshwater and nutrients from both surface-water and groundwater discharge. Surface-water nitrogen loads to the Long Island Sound are relatively well characterized, but less is known about groundwater-transported nitrogen loads. Prior work on the northern shore of Long Island Sound (Connecticut and areas of New York and Rhode Island) suggested that groundwater travel times are relatively short (median less than 2 years) and that decade-long nutrient legacies are not widespread. Because the travel times are short, groundwater flow and nutrient loads likely vary substantially between months. In the current study, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency’s Long Island Sound Study and the Connecticut Department of Energy and Environmental Protection, developed a set of models to better characterize spatial and temporal patterns of groundwater-transported nitrogen loading from atmospheric deposition, septic systems, and fertilizers within the study area. The models provide an estimate, with uncertainty, of groundwater-transported nitrogen loads in the study area, filling a key gap in the nitrogen budget for Long Island Sound. The models also highlight the spatial and temporal variation in nitrogen loading throughout the study area. The modeling workflow involved four models. (1) A soil-water-balance model was developed by using the Soil-Water-Balance software to simulate groundwater recharge across the study area for water years 2005 through 2022. The simulated mean monthly recharge from the soil-water-balance model was used as input into a groundwater-flow model. (2) The groundwater-flow model was developed by using the MODFLOW 6 software and data for water years 1993 through 2022 and simulates average monthly hydrologic conditions. The groundwater-flow model was calibrated by using the Iterative Ensemble Smoother method within the PEST++ software. The Iterative Ensemble Smoother method generates an ensemble of sets of parameter values, with each set producing reasonable simulated hydrologic parameter values. (3) An ensemble of MODPATH particle-tracking simulations were run to generate particle flow paths and travel times, with each simulation using a different set of the flow model parameters. (4) A nitrogen load model uses the MODPATH simulation outputs to track nitrogen from the land surface through multiple attenuation zones until it discharges into fresh or saline surface water. As with the groundwater-flow model, the nitrogen model simulated average monthly groundwater-transported nitrogen loads for water years 1993 through 2022. One novel aspect of the nitrogen load model is that the nitrogen attenuation parameters were calibrated to observed nitrogen loads. Across the ensemble of simulated nitrogen loads, the median study-area-wide monthly simulated nitrogen loads from the aquifer to Long Island Sound throughout the year ranged from 900 to 18,600 kilograms of nitrogen per day, with a median load of 5,100 kilograms of nitrogen per day. The simulated loads were based on average monthly conditions for water years 1993 through 2022. Loads were highest during the winter and early spring and lowest during the late summer. However, simulated travel times for groundwater and nitrogen loads discharged to Long Island Sound during summer were longer than travel times for groundwater and loads discharged during the winter, indicating that, on average, groundwater discharged during summer traveled along different, and longer, flow paths, than groundwater discharged during winter. This indicates that summer loads would respond more slowly to changes in nitrogen inputs at the water table than winter loads. Over the entire study area, approximately 15 percent of the simulated load is from atmospheric deposition sources, 30 to 40 percent is from fertilizer, and 50 to 60 percent is from septic systems. The final analysis of the study involved simulating the change in groundwater-transported nitrogen load in response to upgrading septic systems or reducing fertilizing inputs to areas of turf grass. Both management interventions reduced the groundwater-transported nitrogen load, and reductions were greater in areas with greater loads from septic systems or turf-grass fertilizers. The delay between management actions and substantial reductions in groundwater-transported nitrogen loads varied seasonally; loads during the late summer months remained elevated longer than the winter loads.

Connecticut, Rhode Island↗
USGS2025

Potential for continental scientific drilling to inform fault mechanics and earthquake science

Our understanding of fault mechanics and earthquake processes remains limited, largely due to minimal direct observations near active faults at seismogenic depths. This lack of data restricts our ability to accurately assess and mitigate both natural and human-induced seismic hazards. However, recent advancements in drilling capabilities and downhole sensing technologies offer an opportunity: the ability to observe the physical conditions within a volume near active fault zones. In this contribution, we highlight how scientific drilling can provide access to the near-fault environment, enabling measurements of the stress, temperature, fluid pressure, and rock properties at depths where ruptures initiate, propagate, and arrest. These observations are essential to refine models of earthquake nucleation and dynamic rupture, bridging gaps between laboratory experiments, numerical simulations, and surface observations. These insights can advance fundamental understanding in earthquake science but also support the development of more effective seismic hazard assessments and risk mitigation strategies.

Seismica↗
USGS2024

Earthquake-triggered ground-failure inventory associated with the M7.1 2018 Southcentral Alaska earthquake

The 30 November 2018, magnitude (Mw) 7.1 earthquake in Southcentral Alaska triggered substantial landslides, liquefaction, and ground cracking throughout the region, resulting in widespread geotechnical damage to buildings and infrastructure. Despite a challenging reconnaissance and remote-sensing environment, we constructed a detailed digital inventory of ground failure associated with the event from several sources. Sources included information derived from remotely sensed data, and data compiled from literature, social media postings, and earthquake damage information compiled by local, state, and federal agencies. Each instance of ground failure within the inventory contains information on the location and type of observed ground failure, and the methods and data used to document the occurrence. Where high-quality data, such as LIDAR or satellite imagery, were available and showed the ground-failure instance clearly, the extent is mapped as a polygon or polyline. All other locations are mapped as points. There are a total of 886 ground-failure instances documented within the inventory (400 landslides, 286 liquefaction features, and 200 features unattributed to specific processes). A semi-quantitative confidence scheme is used to describe mapping certainty associated with each ground-failure feature. This inventory represents a relatively moderate ground-failure-triggering event that occurred in a subarctic environment. This data paper describes the content within the inventory, the inventory data collection procedures, and limitations of the data. Events of this type are not often documented in detail; thus, adding the inventory data to the US Geological Survey Open Repository of Earthquake-Triggered Ground-Failure Inventories further diversifies the datasets available to the scientific community to be used to better understand and model earthquake-triggered ground failure.

Alaska↗
USGS2024

Dissolved arsenic concentrations in surface waters within the upper portions of the Klamath River Basin, Oregon and California

Arsenic toxicity is an environmental health problem. Levels of arsenic in surface waters at some locations in the Klamath River Basin in southern Oregon and northern California can exceed the U.S. Environmental Protection Agency (EPA) standard for drinking water. There are both anthropogenic and natural sources of arsenic. The Klamath River Basin consists primarily of volcanic deposits and contains an underground geothermal system with hot springs and warm water wells, all known natural sources of arsenic. Anthropogenic sources of arsenic are related to the agricultural use of herbicides, fungicides, and insecticides. Surface water arsenic levels can also be affected by fertilizer amendments, evaporative concentration, oxygen-level depletion, and various geochemical transformations that can increase arsenic mobilization. In this study by the U.S. Geological Survey and the Bureau of Reclamation, dissolved concentrations of arsenic, copper, and lead were measured in surface waters at 39 unique sites within the upper portions of the Klamath River Basin between 2018 and 2022. In every year, except 2022, sites were sampled four times between April and November. Surface-water arsenic concentrations varied up to four-orders of magnitude among sites. Median arsenic concentration was lowest at Cherry Creek (0.03 micrograms per liter [μg/L]) and highest at Wood Kimball Spring (36.7 μg/L), two sites located north of Upper Klamath Lake. The highest arsenic concentrations (17.4±4.9 μg/L, n =3) were found in drain sites (defined here as a waterbody returning used irrigation water) while the lowest arsenic concentrations were found in an artesian well (0.8 μg/L, n =1). The elevated arsenic concentrations of the drain sites suggest that arsenic might be concentrated or mobilized by agricultural activities, water re-use practices, and (or) by geochemical processes occurring around water stored in drains (that is, in the water column and across sediment water boundaries). A source of arsenic in drain water in the Klamath Strait Drain area includes water used for irrigation originating from Ady Canal. Other potential sources include groundwater, geothermal water, and local soils and sediments. Seasonal differences in surface-water arsenic concentrations were detected at 13 sites, 10 of which had higher arsenic concentrations in summer than in either spring or fall. The sites sampled around Upper Klamath Lake, the impounded rivers, one of the two canal sites, and 5 of the 14 river sites had higher surface-water arsenic concentrations in the summer than in either spring or fall. Surface-water arsenic concentrations from groundwater sources (that is, springs and in the artesian well) did not vary significantly among seasons (p-values greater than 0.1). Median surface-water concentrations of copper and lead ranged from 0.03 to 3.7 μg/L, and from 0.013 to 0.175 μg/L ( n =2–18), respectively. Dissolved concentrations of both metals were below acute toxicity endpoints reported by the EPA for freshwater animals. Surface-water arsenic concentrations varied independently from corresponding changes in surface-water lead or copper concentrations. However, arsenic concentrations measured in bed-sediment samples collected from a subset of sites located north of Upper Klamath Lake correlated strongly and significantly with the corresponding sedimentary lead concentrations ( p =0.015). Aqueous arsenic speciation measured in a subset of sites in 2019 and 2022 showed that all the arsenic existed as arsenic (V), the most oxidized arsenic species, and presumably, the least toxic. The highest proportions of arsenite (As(III)), the presumably most toxic arsenic species, relative to total arsenic concentrations were found at drain sites. Our assessment of dissolved arsenic concentrations in various surface-water bodies in the Upper Klamath River Basin reveals geographical areas of consistently low (below 2.1 μg/L), moderate (below 10 μg/L) and high (above 10 μg/L) surface-water arsenic concentrations. South of Upper Klamath Lake, surface-water arsenic concentrations were consistently higher than 20 μg/L at two drain sites located in an area of predominant agricultural land use with extensive water re-use practices. North of Upper Klamath Lake, surface-water arsenic concentrations greater than 20 μg/L were consistently measured at sites with limited nearby agricultural activities, suggesting a geogenic source. The consistently high arsenic levels from the Wood River at Jackson F. Kimball State Park, Fort Creek, and Crooked Creek, which are sites located at or near headwater spring sources, suggest a natural background source of arsenic. Water flowing downstream from this area could be a potential source of arsenic to Upper Klamath Lake and the Upper Klamath River.

California, Oregon↗
USGS2023

Preliminary geologic map of the Southern Santa Rosa Mountains and Borrego Badlands, San Diego County, Southern California

This investigation delineates the geologic framework of an area of 75 square kilometers (km 2 ) located west of the Salton Sea in southern California (fig. 1, on sheet 1). The study area encompasses the south flank of the Santa Rosa Mountains and the eastern part of the Borrego Badlands (sheet 1). In this study area, regionally important stratigraphic and structural elements collectively inform the late Cenozoic geologic evolution of the Anza-Borrego sector of the Salton Trough province. Critical stratigraphic and structural elements in the map area include the following: The well exposed sequence of late Cenozoic, nonmarine sedimentary rocks that filled the Anza-Borrego subbasin (fig. 1) of the Salton Trough; A tectonic boundary that—in the southern Santa Rosa Mountains—separates the sedimentary strata from underlying crystalline rocks of Peninsular Ranges type. This tectonic boundary, named the West Salton Detachment Fault System by Axen and Fletcher (1998), is projected to underlie all late Cenozoic sedimentary strata in the Anza-Borrego subbasin of the Salton Trough; A variety of transpressional, transtensional, and strike-slip structures that have deformed the late Cenozoic sedimentary strata and collectively guided syntectonic and posttectonic depositional events within the Anza-Borrego subbasin of the Salton Trough; and The southeasternmost surface expression of the Clark Fault, a major strand of the dextral San Jacinto Fault Zone. Geologic mapping and analysis for this investigation focused on clarifying geologic relations among these four stratigraphic and structural aspects in the map area.

California↗
USGS2024

Investigation of land cover within wetland complexes at Dixie Meadows, Churchill County, Nevada, from October 2015 to January 2022

The U.S. Geological Survey investigated land cover at subannual time steps within six wetland areas in Dixie Valley, Churchill County, Nevada, from October 2015 to January 2022. As requested by the U.S. Fish and Wildlife Service, we used aerial photography and satellite remote sensing data to map surface water and other land cover types within the wetland complexes. We identified five land cover classes using the green normalized difference vegetation index (gNDVI) and its inverse relationship to the normalized difference water index (NDWI) within three U.S. Department of Agriculture National Agriculture Imagery Program aerial images (acquired in 2015, 2017, and 2019) and 110 European Space Agency Sentinel-2 satellite images (acquired 2015–2022). The relative wetness of soil conditions within each land cover class is estimated by comparison to previously published observations of relative conductivity measured by 79 field-based sensors within the wetlands from 2019 to 2021. We mapped the areal coverage of the five land cover classes for approximately 385 acres (1,559,000 square meters [m²]) comprising six individual wetland complexes as well as a larger 1,298- acre (5,254,000-m 2 ) area of interest inclusive of the wetland complexes and adjacent landscape. Land cover of open water (Class 5) primarily within ponds at one of the wetland complexes comprised 8,333 m 2 , on average, of the wetland complexes. Land cover of mixed shallow surface water, saturated soil, and vegetation (Class 4) comprised 111,723 m 2 on average of the wetland complexes. Land cover of dense green vegetation canopy cover (Class 3) that often (46 percent of observations) had underlying surface water or saturated soil conditions comprised 592,522 m 2 on average of the wetland complexes. The remaining areas of the wetland complexes not mapped as these three land cover types (Classes 2 and 1) had sparse vegetation or bare soil cover and commonly (greater than or equal to 67 percent of observations) had dry soil conditions. The investigation of land cover detailed in this report could inform future efforts to map land cover more precisely via higher resolution remote sensing or ground-based surveying or could be incorporated with other environmental monitoring data to characterize habitat and hydrology of the wetland complexes at Dixie Meadows.

Nevada↗
USGS2024

Monitoring marine eruptions

Introduction Submarine volcanoes produce much of the same seismicity and eruptive activity as subaerial volcanoes and can pose hazards to society. Although they can be monitored with similar techniques and methods as described in other chapters of this volume, their submerged location brings unique challenges. This chapter addresses these challenges and provides recommendations for monitoring volcanoes fully or partly in marine environments to meet the capabilities described in other chapters of this volume. The United States and its territories host dozens of submarine volcanoes with most (around 60) in the Commonwealth of the Northern Mariana Islands. Approximately 20 of the Northern Mariana Islands submarine volcanoes are known to be hydrothermally active, and 10 have confirmed eruptions since the 1950s (for example, Baker and others, 2008; Tepp and others, 2019a). Nine of those volcanoes were considered by the National Volcanic Threat Assessment (Ewert and others, 2018) to have a combination of eruptive type and summit depth that poses a higher risk of hazardous eruptions, although only one was listed as a moderate (level 3) threat. Other notable submarine volcanoes of interest to the United States that have historically erupted are Axial Seamount off the Washington State coast, Kamaʻehuakanaloa in Hawaiʻi, and Vailuluʻu seamount in American Samoa. All of these, however, have a low risk of hazards because of their depth (greater than 600 meters below sea level) and eruptive type and so are not included in the National Volcanic Threat Assessment. In addition to submarine volcanoes, the submerged flanks of island volcanoes can also be a source of hazardous submarine eruptions—for example, the 1877 eruption of Mauna Loa, Hawai‘i, in Kealakekua Bay (Wanless and others, 2006). The most notable submarine eruption in recent times was the 2022 eruption of Hunga Tonga–Hunga Haʻapai in Tonga, which was one of the largest eruptions on Earth in the past 100 years. It created a massive volcanic plume, unprecedented shock waves, and far-reaching tsunami (Lynett and others, 2022). Other recent submarine eruptions in the Pacific Ocean Basin have produced subaerial plumes that reached aircraft heights (Carey and others, 2014) and large pumice rafts that can affect marine traffic and harbors (for example, Jutzeler and others, 2014; Kornei, 2019). These examples illustrate the potential hazards of major submarine eruptions. Yet, submarine volcanoes are largely unmonitored, and many eruptions occur that are unnoticed or only identified hours or days afterward. Within U.S. territory, submarine volcanoes in the Northern Mariana Islands have been known to produce eruptive activity that can affect society. Reports from fishermen and other marine vessels in the Northern Mariana Islands have noted underwater explosions, sea-surface discoloration, and bubbling water, all of which are known to be signs of submarine volcanic activity. South Sarigan seamount, located about 160 kilometers (km) north of Saipan, erupted in 2010 from greater than 150 meters below the sea surface, resulting in a gas and ash plume that reached more than 11.9 km into the atmosphere (for example, Searcy, 2013; Embley and others, 2014), high enough to affect international air traffic. Precursory and co-eruptive seismicity was detected on the regional Northern Mariana Islands seismic network (Searcy, 2013) and on global monitoring instruments (Green and others, 2013). Monitoring of submarine volcanoes is best accomplished with marine-based instrumentation, which is also useful for monitoring small island volcanoes that may not have the land area necessary for comprehensive subaerial monitoring. The primary marine-based instrumentation used for submarine volcanoes includes ocean-bottom pressure sensors to assess sea-floor deformation, ocean-bottom seismometers (OBSs) to detect seismicity, and both moored and ocean-bottom hydrophones to detect submarine explosions. Other sensors offer important monitoring data, such as turbidity, temperature, and chemistry of hydrothermal emissions. Marine-based instruments are typically deployed in campaign-style networks with no real-time telemetry owing to cost considerations and technical limitations. However, when necessary, marine instruments can be operated in real time using cables to transmit data to land-based facilities; other technologies for this purpose are in use or in development, such as acoustic transmission from the instrument to a moored buoy (Matsumoto and others, 2016) and a winch-based system with a satellite antenna that is part of the instrument mooring (Matsumoto and others, 2019). Emerging technologies for marine-based monitoring may be considered as part of a future monitoring plan. These technologies include ocean gliders and floats with on-board hydrophones that have been used to record earthquakes and submarine eruptions (for example, Matsumoto and others, 2013; Sukhovich and others, 2015) and fiber-optic cables that have been used as strainmeters to detect earthquakes (for example, Marra and others, 2018; Lindsey and others, 2019). Land-based instruments and satellites can also provide some capability for monitoring submarine volcanoes, but they provide more limited observations than marine-based instrumentation.

Scientific Investigations Report↗
USGS1983

Use of digital land-cover data from the Landsat satellite in estimating streamflow characteristics in the Cumberland Plateau of Tennessee

Characteristics of Streamflow at ungaged sites in coal-mining areas of the Cumberland Plateau may be estimated with regression equations that relate streamflow characteristics to the physiographic and climatic characteristics of the corresponding drainage basins. An experiment was performed to compare the accuracy of equations using basin characteristics derived from maps and climatological records (control group equations) with the accuracy of equations using basin characteristics derived from digital processing of Landsat spectral data as well as maps and climatological records (experimental group equations). Results of this experiment show that (with the exception of low flows and four of six annual peak logarithms) drainage area can explain more than 90 percent of the variance in all streamflow characteristics in both groups of equations. Seventeen of 39 experimental group equations that have two basin characteristics each are different from the corresponding control group equations. Five of the 17 differing experimental group equations have no counterpart in the control group because of lack of significance in control group basin characteristics, seven are slightly more accurate, and five are not measurably different in accuracy. When the equations in both groups are arranged into six flow categories, there is no substantial difference in accuracy between equations using basin characteristics derived from maps and climatological records (control group) and equations using basin characteristics derived from Landsat tapes as well as maps and climatological records (experimental group) for this particular study area, the Cumberland Plateau of Tennessee.

Tennessee↗
USGS2024

Evidence of nitrate attenuation in intertidal and subtidal groundwater in a subterranean estuary at a Cape Cod embayment, East Falmouth, Massachusetts, 2015–16

Nitrogen dynamics in intertidal and nearshore subtidal groundwater (subterranean estuary) adjacent to the Seacoast Shores peninsula, Falmouth, Massachusetts, were investigated during 2015–16 by the U.S. Geological Survey. The peninsula is a densely populated residential area with septic systems and cesspools that are substantial sources of nitrogen to groundwater. The study area is in the Eel River, an estuarine saltwater embayment connected to the ocean adjacent to the western shore of the peninsula, that was the subject of an earlier study by Colman and others (2018, https://doi.org/10.3133/sir20185095 ) on nitrogen transport and transformations in groundwater between onshore and offshore locations. The previous study documented the distribution of nitrate concentrations and nitrate attenuation reactions in fresh groundwater beneath the peninsula and the estuary. The current study extended those observations with more detailed sampling and analysis of shallow groundwater from wells near discharge sites beneath the estuary. The current field investigation included sampling of existing wells and installation and sampling of clusters of wells and temporary sampling points in the subterranean estuary, including (1) shallow transects 0.3 to 1.2 meters (m) deep extending from 1 to 13.5 m offshore and (2) deeper wells (from 1.83 to 4.88 m deep) extending from 4.3 to 14.3 m offshore. Measurements of hydraulic-head gradients 2–5 m below the sediment/water interface in the intertidal and nearshore subtidal zones indicated that groundwater flow generally was upwards (towards the estuary) under all tide conditions in October 2016. The magnitude of the gradient was greatest during low tide conditions, indicating that groundwater discharge likely decreased during high tides. Measurements of specific conductance in shallow groundwater in the subterranean estuary in three transects perpendicular to shore were consistent with the existence of saltwater flow cells (infiltration of overlying saline water, mixing with fresh groundwater, and discharge to the overlying saline water) in the intertidal and nearshore subtidal regions. The size of these flow cells was variable in space and time and dependent on the elevation of the tide (spring or neap). At this location in the Eel River subterranean estuary, and offshore to at least 13.5 m, offshore flow of fresh groundwater apparently prevented a deeper saltwater wedge from discharging to the surface. Nitrate concentrations in shallow groundwater (30 to 122 centimeters [cm] depth) were variable in space and time, ranging from not detectable to 600 micromoles per liter (μmol/L) (8.4 milligrams per liter as N), and were highest in June 2016 at depths from 61 to 122 cm below the sediment/water interface and from 4 to 9 m offshore. Nitrate generally was not detectable in saline shallow groundwater at 30-cm depth or at any depth from 30 to 122 cm from 10 to 13.5 m offshore. Dissolved oxygen concentrations were suboxic (less than 16 μmol/L) in 60 percent of the sampled subterranean groundwater beneath the intertidal and subtidal zones. In the remaining sites, the range of dissolved oxygen concentrations was from 18 to 272 μmol/L and the median concentration was 43 μmol/L. Evidence for microbial nitrate reduction (denitrification and possibly anammox) was provided by the distribution of the reaction product nitrogen gas (excess N 2 , or N 2MIC ), as determined from analysis of the dissolved nitrogen gas and argon gas (Ar) concentrations in groundwater samples. Excess nitrogen gas provided evidence for nitrate reduction in shallow groundwater below the subtidal and, to a lesser extent, intertidal zones adjacent to the Seacoast Shores peninsula. These zones, where evidence for nitrate reduction was detected, were in fresh and brackish groundwater near subtidal or intertidal saltwater cells where discharging fresh groundwater mixed with infiltrating saline water. Infiltrating seawater may have supplied organic carbon, one of several potential electron donors that are required for denitrification. Other potential electron donors, such as organic carbon, iron, manganese, hydrogen, methane, ammonium, elemental sulfur, or sulfide phases, may have been supplied by the estuarine sediments. Drainage from surface runoff near the shore also may have supplied organic carbon to fresh groundwater near the intertidal saltwater cell. The highest amounts of nitrate converted to excess nitrogen gas were estimated to be in the range of 230 to 430 μmol/L in nearly fresh groundwater near the subtidal saltwater cell at depths of 61 to 122 cm below the sediment/water interface and from 10 to 13.5 m offshore. Evidence of denitrification within 10 m of the shore was sparse (generally limited to less than 50 μmol/L of N 2 -N) despite the presence of high nitrate concentrations. The spatial distribution of estimated nitrate reduction in the intertidal and nearshore subtidal fresh and brackish groundwater may be related to local variability in the distribution of reactive electron donors in those zones. Variations in the amount of nitrate reduction to nitrogen gas were not clearly related to potential aqueous electron donors such as dissolved organic carbon, nor to potential reaction products such as alkalinity, but may have been controlled by combinations of aqueous and solid-phase reactants. The distribution of relatively shallow fresh groundwater containing nitrate could indicate potential nitrate discharge areas in the lower intertidal zone and uncertain locations farther offshore; however, the data did not extend all the way to the sediment/water interface or to the offshore freshwater limit. This study confirmed substantial loss of nitrate from some of the fresh and brackish groundwater in shallow subestuarine sediments prior to discharge but did not quantify how much nitrate eventually discharged to the estuary.

Massachusetts↗
USGS2025

Scientific opportunities in the National Landscape Conservation System

The National Landscape Conservation System consists of unique and beautiful places across America’s landscapes where identified resources and values are protected and science is highlighted. The mission of the National Landscape Conservation System (NLCS), which is managed by the Bureau of Land Management and is often referred to as the agency’s National Conservation Lands, is to conserve, protect, and restore nationally significant landscapes for their cultural, ecological, and scientific values. This clear inclusion of science in the NLCS mission sets the stage for individual units to serve as places of learning, teaching, discovery, and innovation. Science is an integral part of managing the National Conservation Lands, and science conducted within and across the more than 900 units that make up the NLCS can inform and influence conservation and public land management well beyond its boundaries. Here, we highlight seven core aspects of National Conservation Lands that present valuable science opportunities: (1) the scientific values for which individual units are designated; (2) the many other resources, objects, and values within units; (3) the value of units as “control” sites for understanding the effects of activities such as mineral extraction that commonly occur elsewhere on multiple-use public lands but are often prohibited within National Conservation Lands; (4) the value of units for studying the effects of activities such as recreation that regularly occur and may be intensified on National Conservation Lands; (5) the high visibility of units, which draws strong interest and engagement from scientists, partners, and the public; (6) the functioning of the units as a network managed for a common purpose, which provides an opportunity to explore cross-cutting science questions across widely varying contexts and geographies; and (7) the opportunities units provide to promote and apply Indigenous Knowledge to scientific research to manage natural and cultural resources. Because of all of these characteristics, National Conservation Lands can serve as hubs for basic and applied science that can inform management of all public lands and resources into the future. We highlight these science opportunities through examples from existing units and suggest two actions that could help further science activities and impact on National Conservation Lands.

Parks Stewardship Forum↗
USGS1996

Techniques to estimate generalized skew coefficients of annual peak streamflow for natural basins in Texas

This report presents two techniques to estimate generalized skew coefficients used for log-Pearson Type III peak-streamflow frequency analysis of natural basins in Texas. A natural basin has less than 10 percent impervious cover, and less than 10 percent of its drainage area is controlled by reservoirs. The estimation of generalized skew coefficients is based on annual peak and historical peak streamflow for all U.S. Geological Survey streamflow-gaging stations having at least 20 years of annual peak-streamflow record from natural basins in Texas. Station skew coefficients calculated for each of 255 Texas stations were used to estimate generalized skew coefficients for Texas. One technique to estimate generalized skew coefficients involved the use of regression equations developed for each of eight regions in Texas, and the other involved development of a statewide map of generalized skew coefficients. The weighted mean of the weighted mean standard errors of the regression equations for the eight regions is 0.36 log 10 skew units, and the weighted mean standard error of the map is 0.35 log 10 skew units. The technique based on the map is preferred for estimating generalized skew coefficients because of its smooth transition from one region of the State to another.

Texas↗
USGS2025

A scientific vision and roadmap for earthquake rupture forecast developments, a USGS perspective

We articulate a scientific vision and roadmap for the development of improved Earthquake Rupture Forecast models, which are one of the two main modeling components used in modern seismic hazard and risk analysis. One primary future objective is to provide fully time-dependent models that include both elastic rebound and spatiotemporal clustering nationwide, which is particularly important for shorter-term hazard and risk considerations (e.g., earthquake insurance products). We also discuss the importance and perennial challenges associated with quantifying epistemic uncertainties, including those associated with deformation-model slip rates, un-quantified sampling errors with respect to off-fault seismicity, and any spatial covariances. The need for more physics-based approaches is also emphasized, as is the benefit of adding model valuation (quantifying usefulness) to our verification and validation protocols. Given the multidisciplinary and system-level nature of this activity, modular design is critical. Future updates will also draw from best-available science by both the United States Geological Survey and the external community. The primary goal of this paper is to highlight plans that guide research and facilitate community engagement with model development, especially with respect to lowering the entry barrier for early career scientists and engineers. The paper is written so readers can focus on the sections that interest them most (see table of contents), with the Introduction and Discussion providing a stand-alone overview and summary.

Bulletin of the Seismological Society of America↗
USGS2024

Using geologic mapping to understand temporal and spatial relations of closely clustered to concurrent latest Holocene surface ruptures on two intersecting faults, south-central Mojave Desert, California

The Pinto Mountain Fault Zone (PMFZ) marks a major structural boundary between east-oriented sinistral faults of the eastern Transverse Ranges (to the south) and northwest-oriented dextral faults of the south-central Mojave Desert (to the north). These structural fault systems comprise sinistral and dextral deformational domains of the Eastern California Shear Zone (ECSZ) that intersect one another in the Copper Mountain and Twentynine Palms areas. The U.S. Geological Survey (USGS) is conducting detailed geologic mapping and geochronologic investigations designed to clarify geometric, kinematic, and temporal relations among the two domains, that are focused on the central portion of the left-lateral PMFZ near its intersection with the right-lateral Copper Mountain Fault (CMF) and Mesquite Lake Fault Zone (MLFZ).

California↗
USGS2025

Avian navigation: Comparing the olfactory navigational “map” and the infrasound direction-finding hypotheses to aeronautics

Animal navigation has long been a fascinating but bewildering subject. Humans and animals might well share similar navigational strategies because they developed within the same physical environments. A “map-and-compass” model has been proposed to explain the two-step avian navigational process, but the “map” step has remained elusive. Although scalar values from bicoordinate geomagnetic or atmospheric olfactory gradients have been considered foundational to the avian map, neither has proved convincing engendering decades of controversy. The olfactory map, and an alternative infrasound direction-finding (IDF) hypothesis, are discussed in this review. The olfactory map hypothesis currently requires extensive stable gradients of trace-odor ratios, but such gradients are highly unlikely within a turbulent and rapidly mixed lower atmosphere. The IDF hypothesis, on the other hand, postulates a two-step navigational model analogous to the maritime and aeronautical radio direction-finding technique. This review was also written to encourage further investigation, and direct testing, of the acoustic navigational process. The IDF hypothesis, at present, appears the better explanation of observed avian navigational behavior and accuracy within the atmosphere’s physical environment.

Journal of Comparative Physiology A↗