SEARCH · Geology Reports
Results for “The ISME Journal”
Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Resurvey of the Marble Canyon and Bridge Canyon dam sites in Grand Canyon National Park—Changes in sediment storage and evidence supporting the occurrence of bedrock incision through the mid-20th century
The Bureau of Reclamation developed an extensive plan for a network of dams, water tunnels, and hydropower plants in and around Grand Canyon, Arizona, in the 1940s through 1960s. The two largest of these planned dams were the Marble Canyon and Bridge Canyon Dams on the Colorado River. Though these dams were ultimately never built, Reclamation conducted extensive topographic, bathymetric, and subsurface exploration work at the sites proposed for these dams in the 1940s and 1950s. Resurveys of these dam sites were conducted between 1998 and 2021 to determine the changes in sediment storage at these dam sites caused by the upstream construction and operation of Glen Canyon Dam and by the recession of Lake Mead, the reservoir impounded by Hoover Dam. The resurveys of the Marble Canyon dam sites indicate that the post-1950s changes in sediment storage at these dam sites are broadly consistent with flux-based estimates of voluminous sand erosion from Marble Canyon since the 1963 closure of Glen Canyon Dam. These resurveys also suggest that the pre-dam longitudinal variation in sediment thickness over bedrock played a key role in determining the locations of the sand erosion induced by Glen Canyon Dam; more sand eroded from locations where more sand was present in the 1950s. The resurvey of the Bridge Canyon dam sites indicates that the Colorado River’s incision of the Lake Mead delta is regulated both by bed-sediment grain size and downstream hydraulic controls. Finally, analyses of bed-sediment thickness and sedimentological data at the dam sites, and observations of bed scour and gravel transport, suggest that sufficient bedrock was exposed to allow bedrock incision during commonly recurring pre-dam snowmelt floods that entrained small boulders into transport.
Geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within parts of Bandera and Kendall Counties, Texas
The karstic Edwards and Trinity aquifers are classified as major sources of water in south-central Texas by the Texas Water Development Board. During 2019–23 the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, mapped and described the geology and hydrostratigraphy of the rocks composing the Edwards and Trinity aquifers within parts of Bandera and Kendall Counties from field observations of the surficial expressions of the rocks. The thicknesses of the mapped lithostratigraphic and hydrostratigraphic units were also estimated from field observations in the study area. The Cretaceous rocks in the study area are part of the Trinity Group and Edwards Group. The groups, formations, and members are composed primarily of layers of marls, shales, and limestones. The limestones are composed of mudstone through grainstone, framestone and boundstone, dolomite, and argillaceous and evaporitic rocks. The principal structural feature in the study area is the Balcones fault zone. The Balcones fault zone is the result of late Oligocene and early Miocene extensional faulting and fracturing that was a result of the eastern Edwards Plateau uplift. In the Balcones fault zone, most of the faults in the study area are high-angle to vertical, en echelon, normal faults that are predominantly downthrown to the southeast. Hydrostratigraphically, the rocks exposed in the study area are those that contain the Edwards aquifer, the upper zone of the Trinity aquifer, and the middle zone of the Trinity aquifer. Descriptions of the hydrostratigraphic units, thicknesses, hydrologic function, porosity types, and field identification and observations are provided, including those for the informal Bandera and Love Creek hydrostratigraphic units of the Edwards aquifer, which were identified through the mapping for this study.
A crosswalk of the 2015 World Terrestrial Ecosystems to the International Union for the Conservation of Nature Global Ecosystem Typology Framework
To support ecosystem mapping and accounting applications, we aligned the 2015 U.S. Geological Survey/Esri/The Nature Conservancy-World Terrestrial Ecosystems (WTEs) with the International Union for Conservation of Nature Global Ecosystem Typology (GET) framework. This process, known as “crosswalking,” enabled the development of a global map of GET level 3 Ecosystem Functional Groups (EFGs) at a 250-meter spatial resolution. Crosswalking involved manually assigning 1,781 biogeographically stratified WTEs to their most probable EFG based on similarities in climate, terrain, vegetation, and geographic distribution. We compared attributes of the WTE dataset with summary characteristics of the EFGs. The resulting crosswalked global map of International Union for Conservation of Nature GET ecosystems is intended to be useful for standardizing ecosystem classification and reporting under frameworks such as the Kunming-Montreal Global Biodiversity Framework and the United Nations System of Environmental-Economic Accounting. We discuss key challenges in reconciling non-identical classifications, such as many-to-one relationships and variation in data quality.
The 1912 Ms 7.2 earthquake in the Denali region of central Alaska
The 2002 M w 7.9 earthquake in central Alaska ruptured 340 km on three faults—Susitna Glacier thrust fault, Denali fault, Totschunda fault—crossing both the Richardson Highway and the Alaska Pipeline. Its occurrence prompted renewed interest in historical large earthquakes that possibly originated on the Denali fault. One of these earthquakes was a M s 7.2 event on July 7, 1912, which we revisit with two approaches: (1) probabilistic relocation of the epicenter using globally recorded arrival times, and (2) compilation and reassessment of shaking intensity reports to estimate a macroseismic epicenter. Our preferred instrumental epicenter is west of the Parks Highway and in agreement with the maximum‐reported shaking, which was from the Parker–Browne expedition of Denali. We also relocated a M s 6.4 aftershock, whose epicenter is 11 km from the mainshock. Candidate faults for the 1912 earthquake include the Denali fault, the McLeod Creek thrust fault, and the Kantishna Hills thrust fault. Future analysis of active faults, paleoseismic results, 1912 instrumental data, and 1912 felt reports may help in interpreting the fault and mechanism of the 1912 earthquake.
Hydraulic properties of the Madison aquifer system in the western Rapid City area, South Dakota
Available information on hydrogeology, data from borehole geophysical logs, and aquifer tests were used to determine the hydraulic properties of the Madison aquifer. From aquifer-test analysis, transmissivity and storage coefficient were determined for the Minnelusa and Madison aquifers, and vertical hydraulic conductivity (K v ') along with specific storage (Ss') for the Minnelusa confining bed. Borehole geophysical well logs were used to determine the thickness and location of the Minnelusa aquifer, the lower Minnelusa confining bed, and the Madison aquifer within the Madison Limestone. Porosity values determined from quantitative analysis of borehole geophysical well logs were used in analyzing the aquifer-test data. The average porosity at the two aquifer-test sites is about 10 percent in the Minnelusa aquifer, 5 percent in the lower Minnelusa confining bed, and 35 percent in the Madison aquifer. The first aquifer test, which was conducted at Rapid City production well #6, produced measured drawdown in the Minnelusa and Madison aquifers. Neuman and Witherspoon's method of determining the hydraulic properties of leaky two-aquifer systems was used to evaluate the aquifer-test data by assuming the fracture and solution-opening network is equivalent to a porous media. Analysis of the aquifer test for the Minnelusa aquifer yielded a transmissivity value of 12,000 feet squared per day and a storage coefficient of 3 x 10 -3 . The specific storage of the Minnelusa confining bed was 2 x 10 -7 per foot, and its vertical hydraulic conductivity was 0.3 foot per day. The transmissivity of the Madison aquifer at this site was 17,000 feet squared per day, and the storage coefficient was 2 x 10 -3 . The second aquifer test, which was conducted at Rapid City production well #5 (RC-5) produced measured drawdown only in the Madison aquifer. Hantush and Jacob's method of determining the hydraulic properties of leaky confined aquifers with no storage in the confining bed was used to evaluate the aquifer-test data by assuming the fracture and solution-opening network is equivalent to a porous media. The analysis of data from the RC-5 aquifer test showed that transmissivity was not equal in all directions. Hantush's method was used to determine the direction of radial anisotropy and magnitude of the major and minor axes of transmissivity. The major axis of transmissivity is at an angle of 42° east of north, and the transmissivity along this axis is about 56,000 feet squared per day. The minor axis of transmissivity is at an angle of 48° west of north, and the transmissivity along this axis is about 1,300 feet squared per day. The major axis of transmissivity intersects Cleghorn Springs, a large resurgent spring on the west edge of Rapid City. The shape of the potentiometric contours of the Madison aquifer near RC-5 agree with the orientation of the transmissivity ellipse. The average value of the storage coefficient from the isotropic analysis of the aquifer-test data was 3.5 x 10 -4 , and the average vertical hydraulic conductivity of the lower Minnelusa confining bed was 9.6 x 10 -3 foot per day.
Trace elements in some rocks and slag from the Yemen Arab Republic and their bearing on the iron ore near Sa'dah
Thirty-seven samples of rocks, saprolite, laterite, gossan, and slag were collected in the Yemen Arab Republic during June-July 1975 when field work was conducted to refine an interpretation of the regional geology made from LANDSAT-1 images by M. J. Grolier. These samples we reanalyzed in the laboratories of the U. S. Geological Survey, and the results were interpreted for use in programs of economic development as a guide for the evaluation of mineral resources in the Yemen Arab Republic. The work was undertaken as part of the program of the U. S. Agency for International Development with the cooperation of the Mineral and Petroleum Authority, Ministry of Economy, Yemen Arab Republic.
Geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within northern Medina County, Texas
During 2023–24, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised a previous publication of the geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers that was completed during 2018–20 within northern Medina County, Texas. The purpose of this report is to present the updated geologic framework and hydrostratigraphy of the rocks containing the Edwards and Trinity aquifers in northern Medina County from field observations of the surficial expressions of the rocks. The report includes a detailed 1:24,000-scale hydrostratigraphic map with names and descriptions of the geologic and hydrostratigraphic units (HSUs) in the study area. This study includes updates to the geology of the Kainer Formation (or its stratigraphic equivalent, the Fort Terrett Formation) with the addition of a burrowed unit between the basal nodular and dolomitic members. The hydrostratigraphy was also updated with the addition of HSU IIA for the upper part of the Devils River Limestone and the Seco Pass HSU for the burrowed member of the Kainer (or Fort Terrett) Formation. The Cretaceous age rocks (listed in ascending order) in the study area are part of the Trinity Group, Edwards Group and stratigraphically equivalent Devils River Limestone, Washita Group, Eagle Ford Group, Austin Group, and Taylor Group, with isolated areas where Late Cretaceous age igneous rocks have intruded. The groups and formations are composed primarily of relatively thick layers of clays, shales, and limestone. The igneous rocks are coarse-grained ultramafic in composition. Hydrostratigraphically, the rocks exposed in the study area (listed in descending order from land surface) are igneous, the upper confining unit to the Edwards aquifer, the Edwards aquifer, the upper zone of the Trinity aquifer, and the upper part of the middle zone of the Trinity aquifer. The karstic carbonate Edwards and Trinity aquifers developed because of their original depositional history, primary and secondary porosity, diagenesis, fracturing, and faulting. These factors have resulted in development of modified porosity, permeability, and transmissivity within and between the aquifers.
Examining the role of elevated and sustained strain in dynamically triggering earthquakes on the Anza section of the San Jacinto fault
Microearthquakes can be dynamically triggered in southern California by remote earthquakes. However, directly connecting dynamic triggering mechanisms with observational data remains challenging. One proposed failure mechanism suggests that both the amplitude and duration of cyclic fatigue caused by the passing seismic wave contribute to triggering occurrence. Here, we measure dynamic strains recorded by borehole strainmeters in the Anza section of the San Jacinto fault zone from 710 earthquakes that occurred over 300 km away between 2008 and 2017 to systematically investigate the role of elevated and sustained strain in controlling dynamic triggering. We design a suite of tests to evaluate whether specific amplitude thresholds and durations of strain can predict dynamic triggering cases. We further test whether the peak dynamic strain (PDS) can predict triggering occurrence in combination with the strain amplitude and duration. Based on these tests, there is no strain amplitude–duration threshold that can distinguish triggering occurrence in Anza. Dynamic triggering is more likely to occur if a remote earthquake causes a PDS above 100 nanostrain, though many cases were triggered at smaller PDSs. The lack of clear correlation between triggering and characteristics of the dynamic strain field suggests that the tested features of the incoming waves do not determine triggering occurrence and local fault conditions and slip processes are more important in controlling dynamic triggering in Anza.
The United States Magnetotelluric Array and the National Impedance Map
The United States Magnetotelluric Array (USMTArray) data set, collected in the years 2006–2024, consists of more than 1,700 long-period magnetotelluric stations covering the entirety of the contiguous United States on a quasi-regular 70 km grid. Funding across multiple federal agencies was critical to sustaining this effort to its completion. Important components of the project included active guidance and participation from the MT community, the open and timely availability of all data, and the application of consistent instrumentation and robust data processing. Together with parallel advancement in the development of publicly available three-dimensional (3D) inversion codes, the USMTArray has revitalized the US magnetotelluric community and increased the visibility of magnetotellurics within the Earth-science community. Taken as a whole, these data are visualized as the National Impedance Map, which, together with a 3D synthesis conductivity model of the nation, reveals the electrical architecture of the contiguous US. USMTArray data are used by researchers worldwide for fundamental and applied studies, including investigations of continental architecture and evolution, estimation of hazards to critical infrastructure due to geomagnetic storms, and assessment of the nation's undiscovered geothermal and mineral resources. We here review the history and development of the project, discuss the challenges and successes in its execution, present the National Impedance Map and synthesis conductivity model, and highlight the breadth of research stemming from this rich data set.
Geologic map of the Buckner 7.5-Minute quadrangle, Louisa County, Virginia
The Buckner 7.5-minute quadrangle straddles three terrane boundaries in the Piedmont Physiographic Province in central Virginia: the Chopawamsic terrane, the Elk Hill Complex, and the Goochland terrane. In much of the map area, the Elk Hill Complex separates the Chopawamsic and Goochland terranes. Rocks of the Chopawamsic terrane include Ordovician metavolcanic and metasedimentary rocks of the Chopawamsic Formation, Ordovician to Silurian granodiorite sheet intrusions, and Paleozoic mafic intrusions. Silurian to Devonian rocks of the Quantico Formation, mostly garnet-mica schist, crop out in the northwesternmost part of the map area, and are in unconformable contact with rocks of the Chopawamsic Formation on the southeastern limb of the Quantico synclinorium. The main map unit in the Elk Hill Complex is Neoproterozoic mica gneiss, which is in pre-metamorphic fault contact with rocks of the Chopawamsic Formation to the west. The main map unit of the Goochland terrane is the Maidens Gneiss. Except for Jurassic diabase dikes, all rocks on the Buckner 7.5-minute quadrangle were metamorphosed to amphibolite facies during the Alleghanian orogeny and preserve multiple compositional and phyllosilicate penetrative foliations. Evidence of amphibolite-facies metamorphism during the Taconic orogeny is preserved in rocks of the Elk Hill Complex. The entire width of the Maidens Gneiss on the Buckner 7.5-minute quadrangle is within the Spotsylvania high-strain zone and amphibolite-facies mylonitic textures are pervasive. Quartz veins and Jurassic diabase dikes crosscut all older rocks of the quadrangle. Multiple levels of terrace deposits are present along and near the major streams of the quadrangle. The lower terrace deposits are likely remnants of former positions of the Little River on the landscape, whereas higher deposits may be remnants of former deposits of the Atlantic Coastal Plain that covered this portion of the Piedmont Province. A linear cluster of aftershocks from the magnitude 5.8 earthquake that occurred near Mineral, Virginia, in 2011 defines the Fredericks Hall fault, which is at depth on the Buckner quadrangle. Most of the aftershocks occurred in the core of the Elk Creek antiform and have no relation to faults mapped at the surface. Several abandoned crushed stone and building stone quarries, as well as a mica prospect, exist in the quadrangle.
Altitude of the potentiometric surface and depth to water in the Mississippi River Valley alluvial aquifer, spring 2024
Potentiometric-surface and depth-to-water maps for spring 2024 were created for the Mississippi River Valley alluvial aquifer using groundwater-altitude data from 1,151 wells completed in the Mississippi River Valley alluvial aquifer and from the altitude of the top of the water surface in area rivers from 160 U.S. Geological Survey and U.S. Army Corps of Engineers streamgages. The potentiometric-surface and depth-to-water maps for 2024 were created to support investigations to characterize the Mississippi River Valley alluvial aquifer as part of the U.S. Geological Survey Water Availability and Use Science Program. Sufficient data were available to map the potentiometric surface and depth to water of the Mississippi River Valley alluvial aquifer for spring 2024 for about 83 percent of the aquifer area. The potentiometric contours ranged from 0 to 330 feet (ft) above the North American Vertical Datum of 1988. The regional direction of the groundwater gradient was generally to the south-southwest, except in areas of groundwater-altitude depressions, where the groundwater gradient direction was into the depression, and near rivers, where the groundwater gradient direction was either from the aquifer to the river or from the river into the aquifer. Groundwater depressions in the potentiometric-surface map are in the lower one-half of the Cache region and in most of the Grand Prairie and Delta regions. Depth to water by well in the Mississippi River Valley alluvial aquifer in spring 2024 ranged from 0.27 ft above land surface to 145.65 ft below land surface.
Characterization and simulation of the quantity and quality of water in the Highland Lakes, Texas, 1983-92
The Highland Lakes, located in central Texas, are a series of seven reservoirs on the Colorado River (Lake Buchanan, Inks Lake, Lake Lyndon B. Johnson, Lake Marble Falls, Lake Travis, Lake Austin, and Town Lake). The reservoirs provide hydroelectric power for the area. In addition, Lake Austin and Town Lake also provide the public water supply for the Austin metropolitan area. Saline water released from Natural Dam Salt Lake during 1987–89 caused increased concern among water managers that high-salinity water entering the Highland Lakes could result in waterquality problems, necessitating additional treatment of the water. The maximum dissolved solids concentrations for the reservoirs after the saline inflow were about two to three times the average concentrations before the inflow. The maximum concentrations of chloride and sulfate after the inflow were about three to five times the average concentrations before the inflow. The concentrations of dissolved solids, chloride, and sulfate in Lake Buchanan, Inks Lake, Lake Lyndon B. Johnson, and Lake Marble Falls were less than the concentrations of the applicable water-quality standards by the end of 1990. Concentrations of these constituents in Lake Travis, Lake Austin, and Town Lake did not decrease to previous levels, which were less than the concentrations of the applicable waterquality standards, until the end of 1991. Constituent concentrations for Lake Buchanan and Inks Lake; for Lake Lyndon B. Johnson and Lake Marble Falls; and for Lake Travis, Lake Austin, and Town Lake were similar because of the relative storage capacities and location of tributary inflows. From the initial increase in constituent concentrations in Lake Buchanan (summer 1987) in response to the saline inflow, the high-salinity water passed through the entire Highland Lakes in about 3.5 years. A mathematical mass-balance model was used to simulate the input and movement of highsalinity water through the Highland Lakes and to estimate monthly mean concentrations of dissolved solids, chloride, and sulfate for wet, average, and dry hydrologic conditions. The simulated median monthly concentrations during the 10-year simulation period for each reservoir generally are larger for the average condition than for the wet condition and generally are larger for the dry condition than for the average condition. The simulated concentrations of dissolved solids, chloride, and sulfate decreased to levels less than the concentrations of the applicable water-quality standards in about 2 to 5 years after the saline water inflow of 1987–89 was simulated for the three hydrologic conditions. Results from the simulations indicate that saline inflows to the Highland Lakes similar to those of the releases from Natural Dam Salt Lake during 1987–89 are unlikely to cause large increases in future concentrations of dissolved solids, chloride, and sulfate in the Highland Lakes. The results also indicate that high-salinity water will continue to be diluted as it is transported downstream through the Highland Lakes, even during extended dry periods.
Comparison of hydrologic data and water budgets between 2003–08 and 2018–23 for the eastern part of the Arbuckle-Simpson aquifer, south-central Oklahoma
The Arbuckle-Simpson aquifer is divided spatially into three parts (eastern, central, and western). The largest groundwater withdrawals are from the eastern part of the Arbuckle-Simpson aquifer, which provides water to approximately 39,000 people in Ada and Sulphur, Oklahoma, and surrounding areas. The Arbuckle-Simpson aquifer, including the eastern part, is designated a sole source aquifer for its service area. Based primarily on data collected between 2003 and 2008, a series of comprehensive hydrologic studies of the Arbuckle-Simpson aquifer was published to provide the information necessary to perform groundwater-flow model simulations so that the Oklahoma Water Resources Board could determine how much water could be withdrawn from the aquifer while maintaining flow to springs and streams. As part of the Phase 1 studies, an aquifer water budget was developed from a numerical model for the period 2003–08. For this report, Phase 1 refers to the 2003–08 data collection period, although for some of the analyses, data collected prior to 2003 were used to inform model development work. Allocation of water from this aquifer was then established by the Oklahoma Water Resources Board in 2013. Additional well-spacing rules were also established by the Oklahoma Water Resources Board for sensitive sole source groundwater basins. To determine how the water budget for the eastern part of the Arbuckle-Simpson aquifer has changed over time, recently collected hydrologic data (2018–23) were compared to data collected during 2003–08. The analysis of changes in the aquifer water budget from 2003–08 to 2018–23 could help resource managers better understand changes in the overall balance of water in storage and the potential effects on streamflow, changes in groundwater levels, and the effects of different water uses in the aquifer area on available water in the eastern part of the Arbuckle-Simpson aquifer and streams overlying the eastern part of the Arbuckle-Simpson aquifer.
Wetter winters, drier summers: Quantifying the change in hydrological response around the Puget Sound area using the wflow_sbm hydrological model and CMIP6 projections
Climate change is expected to impact hydrological regimes worldwide, including the Pacific Northwest of the United States. This study investigates how climate change will affect river discharge in the Puget Sound region of the State of Washington, with a focus on King and Pierce Counties. We simulated river discharge under historical and future conditions using the physically based, spatially distributed wflow_sbm hydrological model, which was calibrated and validated against U.S. Geological Survey discharge records. Future forcing was based on an ensemble of six high-resolution CMIP6 climate models, which were bias corrected using empirical quantile mapping. The results indicate a decrease in summer discharges (5–10%) and an increase in winter discharges (5–10%) across the study region. The high discharges (90th percentile) are projected to increase in winter, and the low discharges are projected to decrease in summer, due to shifts in precipitation regimes, snowpack hydrology, and evapotranspiration. However, variability between individual CMIP6 models often exceeds the magnitude of ensemble mean changes, underscoring substantial uncertainty in climate projections and the importance of including multiple climate models in climate change analysis. Furthermore, model consensus increased with elevation, which could be the result of the higher elevation areas being driven by less diverse hydrological processes. These findings highlight potential challenges for regional water management, ecosystem health, and flood risk mitigation in the Puget Sound region under future climate conditions.
Storage timescales and the crystal growth history recorded in the layered reservoir of the Unit 3 Kulanaokuaiki Tephra Member of the Uēkahuna Ash from Kīlauea volcano
The Kulanaokuaiki Tephra Unit 3 (900 C.E.) was a subplinian basaltic scoria eruption, the largest known to have occurred at Kīlauea’s summit. The initiation mechanism and cause(s) of this highly hazardous eruption remain poorly understood, particularly as this style of activity has not been observed in the modern period. We use olivine diffusion timescales from Fe-Mg and lithium zoning to assess magma storage timescales and evaluate evidence for mixing prior to eruption. Of the 200 crystals assessed, 55% are normally zoned for forsterite and 45% are non-zoned. Zoned crystals (> 1 mm) ( n = 96) have average compositions of Fo 89 cores and Fo 81 rims, while small crystals 0.5–1 mm ( n = 14) have Fo 85 cores and Fo 82 rims. Modeled Fo diffusion timescales range from < 1 to 12.6 years (median of 3.0 years). Lithium maps in 32 of the forsterite-zoned crystals reveal a variety of lithium zoning types, most of which we attribute to crystal growth. Many lithium profiles are coupled to phosphorus within the outer ~ 100 μm of the crystal ( n = 17), reflecting growth processes and precluding their use for diffusion studies. Overall, our Unit 3 olivine dataset displays no evidence of magmatic priming shortly prior to eruption, unlike prior observations for the basaltic subplinian eruption of the Keanakāko‘i Tephra Unit E (1650 C.E.). Thus, explosive eruption magmas may be stored for considerably longer than previously thought, and magmatic priming is not a necessary precursor for Kīlauea’s explosive eruptions. We hypothesize that gas-driven filter pressing from crystallization of microlites and macrocrysts in the reservoir slurry contributed to the explosivity of the Unit 3 eruption.
Updating the crustal fault model for the 2023 National Seismic Hazard Model for Alaska
We present the crustal fault model for Alaska, based on geologic observations, as a primary input for the 2023 revision of the U.S. Geological Survey National Seismic Hazard Model. We update the 2013 Alaska Quaternary fault and fold database to produce a simplified model of 105 fault sections and four fault zone polygons with basic geologic parameters including slip sense and rate. Significant updates include the following: (1) a slip rate of ∼53 mm/year on the Queen Charlotte Fault indicating it accommodates all of the plate boundary motion; (2) quantified slip rates on megathrust splay faults in the southern Prince William Sound region and near Kodiak Island; (3) improved details of structures in the Chugach-St. Elias orogen; (4) revision of the Castle Mountain Fault from right-lateral slip to a predominantly reverse fault; (5) improved Interior Alaska tectonic models that clarify relationships between the Denali, Totschunda, and thrust faults on both sides of the Alaska Range; (6) identified large earthquake sources in the eastern Brooks Range; and (7) omission of the Chatham Strait section of the Denali Fault. The fault model underscores that the collision of the Yakutat microplate is the dominant driver of active crustal faulting in most of Alaska.