Geology ReportsSearch

SEARCH · Geology Reports

Results for “JGR Machine Learning and Computation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,658 records · Page 12Linked to original sources

Methods for estimating selected low-flow statistics at gaged and ungaged stream sites in Massachusetts

The U.S. Geological Survey, in cooperation with the Massachusetts Department of Conservation and Recreation, Office of Water Resources, computed selected at-site streamflow statistics at U.S. Geological Survey streamgages in and near Massachusetts and developed regional regression equations for estimating selected streamflows at ungaged stream sites in Massachusetts. Two sets of regional regression equations were developed: (1) the “mainland” equations, for mainland Massachusetts excluding the area covered by the second set, and (2) the “southeastern” equations, for the Plymouth-Carver-Kingston-Duxbury aquifer area in southeastern Massachusetts and for Cape Cod. The regression equations and at-site statistics may be used by Federal, State, and local water managers in addressing water-resources issues relevant in Massachusetts. Regional regression analyses for the mainland equations were developed to estimate the following 27 streamflow statistics: 99-, 98-, 95-, 90-, 85-, 80-, 75-, 70-, 60-, and 50-percent flow durations; monthly June, July, August, and September 90- and 50-percent flow durations; February, June, and August median of the monthly means; harmonic mean; and medians of the following annual low-flow frequency statistics: 7-day; 7-day, 2-year; 7-day, 10-year; 30-day, 2-year; and 30-day, 10-year. The analyses used 81 streamgages with minimal to no regulations in and near Massachusetts. The regression analyses determined that four basin characteristics—drainage area, combined hydrologic soils A and B, streamflow variability index, and annual mean temperature—were the only significant explanatory variables for the different mainland equations. Regional regression equations were developed for the Plymouth-Carver-Kingston-Duxbury aquifer area in southeastern Massachusetts and Cape Cod, because surface-water drainage areas and groundwater contributing areas do not always coincide in this area of the State. The regression analyses to estimate 10 flow durations from the 99th to 50th percentiles used 18 streamflow sites with some occasional minor regulations—because there are few unregulated streams in southeastern Massachusetts. The analyses determined that groundwater contributing area and storage (combined water bodies and wetlands) were the only significant explanatory variables in the southeastern equations.

Massachusetts

Near-surface material and topography generate anomalous high-frequency ground motion amplification in Chugiak, Alaska

An ∼3 km long nodal array oriented approximately east–west was deployed in Chugiak, Alaska, by the U.S. Geological Survey during 2021. The array intersects with the permanent NetQuakes station NP.ARTY, where peak ground acceleration (PGA) value of 1.98 g was recorded during the 2018 M w 7.1 Anchorage, Alaska, earthquake, in sharp contrast to the PGA of ∼0.3 g at a site just 4 km to the west. Seismic data for M w 1.8–4.3 aftershocks from the M w 7.1 event recorded by the nodal array confirm the anomalously large ground motions obtained at NP.ARTY as well as similar amplifications at nodes within ∼1 km to the east. Here, we performed 0–10 Hz 3D finite‐difference simulations, including high‐resolution surface topography, to explore the cause of the unexpectedly large amplification. As expected, the simulations computed with a regional 3D tomography velocity model severely underpredict the 0–10 Hz acceleration records at almost all sites. Adding a near‐surface low‐velocity taper to 300 m depth amplifies the accelerations by up to a factor of 5 and enables a reasonable match between the nodal data and simulations at sites to the west of NP.ARTY. However, this model still underpredicts the spectral energy in the area covered by glacial sediments by up to an order of magnitude. The addition of a till layer using a depth‐dependent shear‐wave velocity ( ⁠⁠ V s ) profile along with a homogeneous, 8 m thick low‐velocity layer with V s = 250 m/s representing the kame terraces improves the fit to data to within a factor of 2 at nodes located on top of the glacial sediments. Our study shows that the anomalously large high‐frequency amplification recorded at and near NP.ARTY can be explained by a combination of topographic effects and near‐surface low‐velocity material with amplification effects on the high‐frequency ground motion by up to about 40% and an order of magnitude, respectively.

Alaska

Determining Volcanic Risk in Auckland (DEVORA) Research Programme—A transdisciplinary approach to address the challenge of distributed volcanism in an urban environment

The Determining Volcanic Risk in Auckland (DEVORA) Research Programme was launched in 2008 to address the challenges associated with monogenetic volcanism in an urban setting and to enhance volcanic risk management in Tāmaki Makaurau Auckland in Aotearoa New Zealand. It is a multi-agency, increasingly transdisciplinary (defined here as research that transcends traditional disciplinary boundaries by integrating diverse types of knowledge, perspectives, and methods from academic and non-academic participants to create novel solutions to complex problems), and collaborative research program jointly led by Waipapa Taumata Rau University of Auckland and Earth Sciences New Zealand (ESNZ; formerly GNS Science), with core funding from Natural Hazards Commission Toka Tū Ake (NHC; formerly the Earthquake Commission, EQC) and Te Kaunihera o Tāmaki Makaurau Auckland Council (AC). The primary research focus of DEVORA is to investigate the geologic history, volcanic hazards, and risk posed by the basaltic intraplate Auckland Volcanic Field. Disruption from ash fall and gas from other Aotearoa New Zealand volcanoes is also considered. DEVORA’s work to explore exposure and vulnerability in Tāmaki Makaurau Auckland is also useful for assessing risks from other non-volcanic natural hazards, such as seismic and tsunami hazards. The greater Tāmaki Makaurau Auckland region has an ethnically and socio-economically diverse population of approximately 1.7 million, representing about one-third of the Aotearoa New Zealand population, and hosts critical infrastructure of national significance. The size and nature of the populace, consequential economic base, and important infrastructure within Tāmaki Makaurau Auckland mean that the effects of a volcanic eruption would be felt nationally, including through the disruption of air travel to Aotearoa New Zealand. The hazards from such an eruption could potentially affect hundreds of thousands of people, businesses, and lifelines (critical infrastructure). A considerable challenge for emergency and risk managers is the monogenetic nature of the volcanic field. It is not known where or when the next eruption will occur, how much warning we may get before an eruption, nor how an eruption and its effects might unfold. In this contribution, we highlight the concept and collaborative intent of the DEVORA Programme and show how it has evolved over the 16 years since its inception. We describe how DEVORA has unified more than 100 researchers (including more than 50 graduate students) and numerous stakeholders to address key issues facing Tāmaki Makaurau Auckland and describe how research findings are being implemented into policy and communicated to stakeholder agencies and the public. We also illustrate the broader influence of the DEVORA Programme and provide some learnings that might benefit others embarking on similar integrated projects, especially those focused on distributed volcanism in and near populated areas.

Auckland

Quality assurance and analysis of water levels in wells on Pahute Mesa and vicinity, Nevada Test Site, Nye County, Nevada

Periodic and continual water-level data from 1963 to 1998 were compiled and quality assured for 65 observation wells on Pahute Mesa and vicinity, Nye County, Nevada. As part of the quality assurance of all water levels, ancillary data pertinent to computing hydraulic heads in wells were compiled and analyzed. Quality-assured water levels that were not necessarily in error but which did not represent static heads in the regional aquifer system, or required some other qualification, were flagged. Water levels flagged include those recovering from recent pumping or well construction, water levels affected by nuclear tests, and measurements affected by borehole deviations. A cursory examination of about 30 wells with available water-level and down-hole temperature data indicate that water levels in most wells on Pahute Mesa would not be significantly affected by temperature if corrected to 95 degrees Fahrenheit. Wells with large corrections (greater than 10 feet) are those with long water columns (greater than 1,500 feet of water above the assumed point of inflow) in combination with mean water-column temperatures exceeding 105 degrees Fahrenheit. Water-level fluctuations in wells on Pahute Mesa are caused by several factors including infiltration of precipitation, barometric pressure, Earth tides, ground-water pumpage, and seismic events caused by tectonic activity and underground nuclear testing. No observed water-level fluctuations were attributed to a naturally occurring earthquake. The magnitude and duration of changes in water levels caused by nuclear tests are affected by the test size and the distance from a well to the test. Identifying water levels that might be affected by past nuclear tests is difficult because pre-testing water-level data are sparse. Hydrologically significant trends were found in 13 of 25 wells with multiple years of water-level record. The largest change in water levels (1,029 feet in 25 years) occurred in well U-19v PS 1D as a result of the Almendro nuclear test. Likely explanations for trends in most of the wells are either changes in precipitation patterns that affect recharge rates to the ground-water system, pumping effects from water-supply well U-20 WW, or a combination of these two factors.

Nevada

Geochemistry of and radioactivity in ground water of the Highland Rim and Central Basin aquifer systems, Hickman and Maury counties, Tennessee

A reconnaissance of the geochemistry of and radioactivity in ground water from the Highland Rim and Central Basin aquifer systems in Hickman and Maury Counties, Tennessee, was conducted in 1989. Water in both aquifer systems typically is of the calcium or calcium magnesium bicarbonate type, but concentrations of calcium, magnesium, sodium, potassium, chloride, and sulfate are greater in water of the Central Basin system; differences in the concentrations are statistically significant. Dissolution of calcite, magnesium-calcite, dolomite, and gypsum are the primary geochemical processes controlling ground-water chemistry in both aquifer systems. Saturation-state calculations using the computer code WATEQF indicated that ground water from the Central Basin system is more saturated with respect to calcite, dolomite, and gypsum than water from the Highland Rim system. Geochemical environments within each aquifer system are somewhat different with respect to dissolution of magnesium-bearing minerals. Water samples from the Highland Rim system had a fairly constant calcium to magnesium molar ratio, implying congruent dissolution of magnesium-bearing minerals, whereas water samples from the Central Basin system had highly variable ratios, implying either incongruent dissolution or heterogeneity in soluble constituents of the aquifer matrix. Concentrations of radionuclides in water were low and not greatly different between aquifer systems. Median gross alpha activities were 0.54 picocuries per liter in water from each system; median gross beta activities were 1.1 and 2.3 picocuries per liter in water from the Highland Rim and Central Basin systems, respectively. Radon-222 concentrations were 559 and 422 picocuries per liter, respectively. Concentrations of gross alpha and radium in all samples were substantially less than Tennessee’s maximum permissible levels for community water-supply systems. The data indicated no relations between concentrations of dissolved radionuclides (uranium, radium-226, radium-228, radon-222, gross alpha, and gross beta) and any key indicators of water chemistry, except in water from the Highland Rim system, in which radon-222 was moderately related to pH and weakly related to dissolved magnesium. The only relation among radiochemical constituents indicated by the data was between radium-226 and gross alpha activity; this relation was indicated for water from both aquifer systems.

Tennessee

Probabilistic assessment of postfire debris-flow inundation in response to forecast rainfall

Communities downstream of burned steep lands face increases in debris-flow hazards due to fire effects on soil and vegetation. Rapid postfire hazard assessments have traditionally focused on quantifying spatial variations in debris-flow likelihood and volume in response to design rainstorms. However, a methodology that provides estimates of debris-flow inundation downstream of burned areas based on forecast rainfall would provide decision-makers with information that directly addresses the potential for downstream impacts. We introduce a framework that integrates a 24 h lead-time ensemble precipitation forecast with debris-flow likelihood, volume, and runout models to produce probabilistic maps of debris-flow inundation. We applied this framework to simulate debris-flow inundation associated with the 9 January 2018 debris-flow event in Montecito, California, USA. When the observed debris-flow volumes were used to drive the probabilistic forecast model, analysis of the simulated inundation probabilities demonstrates that the model is both reliable and sharp. In the fully predictive model, however, in which debris-flow likelihood and volume were computed from the atmospheric model ensemble's predictions of peak 15 min rainfall intensity, I 15 , the model generally under-forecasted the inundation area. The observed peak I 15 lies in the upper tail of the atmospheric model ensemble spread; thus a large fraction of ensemble members forecast lower I 15 than observed. Using these I 15 values as input to the inundation model resulted in lower-than-observed flow volumes which translated into under-forecasting of the inundation area. Even so, approximately 94 % of the observed inundated area was forecast to have an inundation probability greater than 1 %, demonstrating that the observed extent of inundation was generally captured within the range of outcomes predicted by the model. Sensitivity analyses indicate that debris-flow volume and two parameters associated with debris-flow mobility exert significant influence on inundation predictions, but reducing uncertainty in postfire debris-flow volume predictions will have the largest impact on reducing inundation outcome uncertainty. This study represents a first step toward a near-real-time hazard assessment product that includes probabilistic estimates of debris-flow inundation and provides guidance for future improvements to this and similar model frameworks by identifying key sources of uncertainty.

California

Estimated groundwater recharge for mid-century and end-of-century climate projections, Kaua‘i, O‘ahu, Moloka‘i, Lāna‘i, Maui, and the Island of Hawai‘i

Demand for freshwater in the State of Hawaiʻi is expected to increase by roughly 13 percent from 2020 to 2035. Groundwater availability in Hawaiʻi is affected by a number of factors, including land cover, rainfall, runoff, evapotranspiration, and climate change. To evaluate the availability of fresh groundwater under projected future-climate conditions, estimates of groundwater recharge are needed. A water-budget model with a daily computation interval was used to estimate the spatial distribution of groundwater recharge for Kauaʻi, Oʻahu, Molokaʻi, Lānaʻi, Maui, and the Island of Hawaiʻi for recent climate conditions and three future-climate scenarios. Climate conditions from 1978 to 2007 were used as the reference period for recent climate conditions on each island. The three future-climate scenarios were developed using available high-resolution downscaled climate projections that include (1) a mid-century scenario using projected rainfall conditions for the Representative Concentration Pathway (RCP) scenario during 2041–71 with a total radiative forcing of 8.5 watts per square meter by the year 2100 (RCP8.5 2041–71 scenario), (2) a dry-climate scenario using projected rainfall conditions for the RCP8.5 scenario during 2071–99, and (3) a wet-climate scenario using projected rainfall conditions for the “Special Report on Emissions Scenarios” A1B scenario during 2080–99 for Maui, the RCP4.5 scenario during 2080–99 for Kauaʻi, Lānaʻi, and the Island of Hawaiʻi, and the RCP8.5 scenario during 2080–99 for Oʻahu and Molokaʻi. An additional drought scenario was added for Lānaʻi to assess the effect of extreme drought conditions during 2008–12 on groundwater recharge. All scenarios used 2020 land cover. Mean annual groundwater recharge is estimated to decrease between 5 and 55 percent on all six islands in this study for the mid-century and dry-climate scenarios relative to the reference-period recharge. Recharge is estimated to increase for Kauaʻi, Oʻahu, Molokaʻi, Lānaʻi, and Maui between 2 and 43 percent and decrease for the Island of Hawaiʻi by about 4 percent for the wet-climate scenario. Comparing the mid-century and dry-climate scenarios, all 110 aquifer systems (management areas defined by the State of Hawaiʻi Commission on Water Resource Management) from all six islands show similar direction in drying (104 aquifer systems) or wetting (6 aquifer systems) changes for recharge. However, among the three future scenarios, only 35 of 110 aquifer systems show similar direction in drying (30 aquifer systems) or wetting (5 aquifer systems) changes for recharge.

Hawaii

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri River near Kansas City, Missouri, August 8–9, 2023

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near 8 bridge crossings of the Missouri River near Kansas City, Missouri, on August 8–9, 2023. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches that extended about 1,550 to 1,640 feet longitudinally and generally extended laterally across the active channel from bank to bank during low floodflow to nonflood conditions. These surveys provided the channel geometry and hydraulic conditions of the river at the time of the surveys and provided characteristics of scour holes, which may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. The data collected from the surveys may also be useful to the Missouri Department of Transportation as a record of low floodflow conditions in regards to the stability and integrity of the bridges with respect to bridge scour. Bathymetric data were collected around every in-channel pier. Scour holes were at most piers where bathymetry could be obtained, except for those piers on banks or surrounded by riprap. All the bridge sites in this study were surveyed and documented in previous studies. The average difference between the bathymetric surfaces ranged from 0.07 to 4.16 feet higher in 2023 than 2019, which indicates overall deposition between the survey dates, as might be expected based purely on streamflow at the time of the survey. However, the average difference between the bathymetric surfaces ranged from 1.44 feet higher to 1.88 feet lower in 2023 than 2015, which indicates a dynamic equilibrium of scour and deposition overall between those surveys, despite the lower flow conditions in 2023. Similarly, the average difference between the bathymetric surfaces ranged from 3.18 feet higher to 5.19 feet lower in 2023 than 2011, which indicates a relative equilibrium between scour and deposition overall, albeit the trend was toward scour as might be expected because of the substantial flood event in 2011. Riprap blankets and alignment to flow had a substantial effect on the size of the scour hole for a given pier. Piers that were partially or fully surrounded by riprap blankets had scour holes that were substantially smaller (to nonexistent) compared to piers with no rock or riprap and effectively mitigated the scour holes historically observed at these piers. Several of the structures had piers that were skewed to primary approach flow. At most of the structures, the scour hole was deeper and longer on the side of the pier with impinging flow than the leeward side, with some amount of deposition on the leeward side, as typically observed at piers skewed to approach flow.

Kansas, Missouri

Conventional hydrothermal power-producing systems of the Great Basin, USA

As part of the update to the electric-grade conventional hydrothermal assessment of the Great Basin, USA, Monte Carlo analyses of identified resources within explored regions will be performed to make estimates of discovered resources and associated uncertainty. Analyses use conditional statistics where estimates are conditioned upon a hydrothermal favorability map, allowing for the likelihood that more resources exist in regions of higher hydrothermal favorability. For these analyses, a dataset of identified hydrothermal systems is compiled, and the new compilation is described herein. Recognizing that a single hydrothermal system may be developed with multiple power plants, and that the hydrothermal upflow zone may be several kilometers across with many measurements characterizing a single hydrothermal system, a procedure was developed and employed to create clusters of points (power plants, measurements, etc.) that are associated with a single system, and a new central point was defined as the best estimator of the center of the hydrothermal system. Hydrothermal systems were uniquely identified by grouping electric-grade hydrothermal measurements and operating power plants within a distance of 10 km. Groups that are >10 km apart are assumed to be different electric-grade hydrothermal systems. While 10 km was used as the threshold, most systems were significantly further apart, and most points within groups were typically within 5 km of each other. A well measurement was considered an electric-grade measurement of a hydrothermal system if it had two properties: a measured temperature of >85 °C and evidence of hydrothermal convection. Other points that were added to the dataset are locations of operating powerplants or locations that have been classified as an electric-grade hydrothermal resource by either the U.S Geological Survey (USGS) or the Great Basin Center for Geothermal Energy. After all points are assigned to systems, new points were computed with the goal of identifying the center of the throat of the hydrothermal upflow zone. If operating powerplants exist for a system, then the arithmetic average of all power plant locations is used. Otherwise, if USGS made an estimate, that location is used. In the absence of both powerplants or USGS estimates, the arithmetic average of all electric-grade measurement locations is used. An example is shown of how these newly compiled locations might be ranked for uncertainty analyses, where higher confidence is assumed if measured temperature is higher and there are many supporting measurements indicating an electric-grade resource. In summary, 28 systems have operating power plants, an additional 78 systems are known identified electric-grade hydrothermal resources, and 99 new systems were identified as probable electric-grade systems with varying levels of confidence. These 205 locations are shown as a function of a recent hydrothermal favorability map, conceptually illustrating the conditional statistics that can be used to make estimates of the undiscovered resources of the Great Basin. An accompanying data release provides summaries of developed capacity by system and USGS estimates of likely total capacity and associated uncertainty.

Arizona, California, Idaho, Nevada, Oregon, Utah

Streamflow, ground-water recharge and discharge, and characteristics of surficial deposits in Buzzards Bay Basin, southeastern Massachusetts

Streamflow measurements at 14 low-flow partial-record stations and two discontinued streamflow-gaging stations were related to concurrent streamflows at six long-term streamflow-gaging stations to estimate streamflows at selected flow durations from 50 to 99 percent for water years 1967-91. At low flows, stream discharge per square mile generally increased with increasing percentage of subbasin underlain by stratified-drift deposits. At the 70-, 90-, and 99-percent flow durations, subbasins underlain primarily by stratified-drift deposits had stream discharges per square mile at least 2, 4, and 8 times greater, respectively, than subbasins underlain primarily by till and bedrock deposits. Streamflow measured three times at the Paskamanset River showed that streamflows downstream of municipal pumped wells increased at a lower rate per unit drainage area than streamflows upstream of the pumped wells. When pumpage from wells near the river was added to measured streamflow at the most downstream station, the sum was similar to the potential streamflow at the station if its streamflow per unit area was the same as that upstream from the pumped wells. Mean ground-water recharge and discharge rates were computed from continuous records of daily mean discharge during water years 1967-91 for six streamflow-gaging stations in southeastern Massachusetts and Rhode Island. Estimates of mean ground-water recharge were 19.7 to 22.6 inches per year for stations with drainage areas primarily underlain by till and bedrock deposits, and 23.8 to 25.2 inches per year for stations with drainage areas primarily underlain by stratified-drift deposits. During drought years, annual ground-water recharge can be less than 50 percent of the mean ground-water recharge rate for water years 1967-91. Estimates of ground-water discharge rates generally were 1 to 4 inches per year less than estimates of ground-water recharge rates. Ground-water discharge-duration curves were calculated from hydrograph separation of streamflow records at the six continuous streamflow-gaging stations for water years 1967-91. When streamflows were less than the median streamflow (50-percent duration), ground-water discharges averaged 85.7 percent of the total streamflow at the six streamflow-gaging stations. Ground-water discharges were estimated at the 14 low-flow partial-record stations and two discontinued streamflow-gaging stations by multiplying streamflows at the selected flow durations from 50 to 99 percent for water years 1967-91 by 85.7 percent. Data on surficial deposits in the basin were obtained by drilling 10 wells, by conducting 12 seismic-refraction surveys, and by collecting well log data for 313 wells from consulting firms and the Massachusetts Department of Environmental Management. These data indicated that a few minor corrections could be made to existing saturated thickness maps for stratified-drift deposits in Buzzards Bay Basin. Few well logs were detailed enough to estimate transmissivities; thus existing transmissivity maps were not updated for stratified-drift deposits in the basin.

Massachusetts

Multiple-well monitoring site adjacent to the Midway- Sunset and Buena Vista Oil Fields, Kern County, California

Groundwater quality in and around oil fields in the Southern San Joaquin Valley is of interest to many California residents that rely heavily on groundwater for domestic, commercial, and agricultural use. To help assess the effects of historical oil-field activities and natural geologic sources on groundwater near the southwest margins of the Kern County Groundwater Subbasin, a multiple-well monitoring site was installed near the administrative boundary between the Midway-Sunset and Buena Vista Oil Fields in Kern County, California. The installation of the Midway-Sunset Buena Vista multiple-well monitoring site (MSBV) supports regional analysis of the relations of oil and gas sources to groundwater quality by providing information about the geology, hydrology, geophysical properties, and water quality of the alluvial and upper Tulare aquifers in areas where groundwater data were limited. Data collected from the site included drill cuttings, whole core samples, sidewall core samples, mud-gas analysis, borehole geophysical logs, depth to water measurements, and water quality samples. Whole cores were scanned using dual energy computed tomography. Subsamples of selected cores were analyzed for density, porosity, specific retention, and bulk minerology. Thin sections of the subsamples were prepared, photographed, and examined. Two samples were analyzed using scanning electron microscope technology to examine the microporosity of diatomite laden sediment. Instrumentation installed in the wells collect hourly depth to water measurements. Analysis of the data show there is 355 feet of alluvium overlying the Tulare Formation at the well site. The contact between the two formations is an aquitard resulting in a perched aquifer in the alluvium and unconfined aquifer in the Tulare Formation. The alluvium is more heterogenous and finer grained than the Tulare Formation resulting in markedly higher porosity in the alluvium compared to the Tulare Formation. Higher specific retention observed in the alluvium is attributed to the finer grained sediment and greater abundance of reworked diatomite (as represented by opal-CT [cristobalite-tridymite]) compared to the Tulare Formation. Total dissolved solids (TDS) approached or exceeded 10,000 milligrams per liter (mg/L) in the alluvium from approximately 176 to 242 feet below land surface and at the top of the Amnicola clay at approximately 670 feet below land surface within the Tulare Formation. Elevated TDS, chloride, and boron concentrations in the alluvium and on top of the Amnicola clay likely reflect groundwater that is mixed with oil-field water. Water chemistry and modern-aged groundwater in the alluvial monitoring well (MSBV #3) are consistent with the oil-field water in the alluvium being derived from documented historical surface disposal of oil-field water upslope (northwest) of the site. Water chemistry and pre-modern groundwater age in the deeper Tulare monitoring well (MSBV #1) on top of the Amnicola clay are consistent with oil-field fluids derived from upslope natural geologic sources or old oil wells that leak in the subsurface. Shallow groundwater in the Tulare (MSBV #2) is not affected by mixing with oil-field sources.

EarthArXiv

Hydrogeologic investigation and simulation of ground-water flow in the Upper Floridan Aquifer of north-central Florida and southwestern Georgia and delineation of contributing areas for selected city of Tallahassee, Florida, water-supply wells

A 4-year investigation of the Upper Floridan aquifer and ground-water flow system in Leon County, Florida, and surrounding counties of north-central Florida and southwestern Georgia began in 1990. The purpose of the investigation was to describe the ground-water flow system and to delineate the contributing areas to selected City of Tallahassee, Florida, water-supply wells. The investigation was prompted by the detection of low levels of tetrachloroethylene in ground-water samples collected from several of the city's water-supply wells. Hydrologic data and previous studies indicate that; ground-water flow within the Upper Floridan aquifer can be considered steady-state; the Upper Floridan aquifer is a single water-bearing unit; recharge is from precipitation; and that discharge occurs as spring flow, leakage to rivers, leakage to the Gulf of Mexico, and pumpage. Measured transmissivities of the aquifer ranged from 1,300 ft 2 /d (feet squared per day) to 1,300,000 ft2/d. Steady-state ground-water flow in the Upper Floridan aquifer was simulated using a three-dimensional ground- water flow model. Transmissivities ranging from less than 5,000 ft2/d to greater than 11,000,000 ft 2 /d were required to calibrate to observed conditions. Recharge rates used in the model ranged from 18.0 inches per year in areas where the aquifer was unconfined to less than 2 inches per year in broad areas where the aquifer was confined. Contributing areas to five Tallahassee water-supply wells were simulated by particle- tracking techniques. Particles were seeded in model cells containing pumping wells then tracked backwards in time toward recharge areas. The contributing area for each well was simulated twice, once assuming a porosity of 25 percent and once assuming a porosity of 5 percent. A porosity of 25 percent is considered a reasonable average value for the Upper Floridan aquifer; the 5 percent porosity simulated the movement of ground-water through only solution-enhanced bedding plains and fractures. The contributing areas were generally elliptical in shape, reflecting the influence of the sloping potentiometric surface. The contributing areas delineated for a 5 percent porosity were always much larger than those determined using a 25 percent porosity. The lowest average ground-water velocity computed within a contributing area, using a 25 percent porosity, was 1.0 ft/d (foot per day) and the highest velocity was 1.6 ft/d. The lowest average ground-water velocity, determined using a 5 percent porosity, was 2.4 ft/d and the highest was 7.4 ft/d. The contributing areas for each of the five wells was also determined analytically and compared to the model-derived areas. The upgradient width of the simulated contributing areas were larger than the upgradient width of the analytically determined contributing areas for four of the five wells. The model could more accurately delineate contributing areas because of the ability to simulate wells as partially penetrating and by incorporating complex, three-dimensional aquifer characteristics, which the analytical method could not.

Florida, Georgia

Effective site coefficients for the 2024 International Building Code (IBC)

The U.S. National Seismic Hazard Models (NSHMs), developed by the U.S. Geological Survey (USGS), have long been the scientific foundation of seismic design guidelines and have been used to compute design ground motions for construction of new buildings and retrofit of existing buildings in the United States and its territories. The 2018 NSHM is adopted by the 2024 International Building Code (IBC). Prior to the 2018 NSHM update, hazard calculations were required only at one reference site condition defined by V S30 =760 m/s (where V S30 is the time-averaged shear wave velocity from the surface to a depth of 30 m) and three periods (peak ground acceleration, PGA, and pseudo spectral accelerations at periods of 0.2 and 1 s, S s and S 1 ). Site coefficients, F PGA , F a , and F v , were then defined by the Building Seismic Safety Council (BSSC) Provisions Update Committee (PUC) in the site-specific procedures of National Earthquake Hazard Reduction Program (NEHRP) Recommended Seismic Provisions to calculate ground motions for other site classes with different V S30 values at the given periods. The design ground motions at other periods were then estimated using a generic spectral shape that was also defined by the BSSC PUC in NEHRP provisions. In recent years, the engineering community has realized there were deficiencies with the F a and F v site coefficients and the generic spectral shape. To avoid potentially dangerous underestimations of design ground motions for long period structures on soft site conditions in high seismicity regions, the BSSC PUC recommended the use of multi-period response spectra (MPRS) in 2017. As a result, the USGS produced multi-period and multi-V S30 response spectral values in the 2018 NSHM for calculations of design ground motions and the site coefficients F a and F v were eliminated from the 2020 NEHRP Provisions. As these site coefficients were widely used inside and outside of the United States, in this study we back-calculate the “effective” site coefficients F a,eff , and F v,eff by comparing MPRS for various site classes with the MPRS for the reference site condition, and discuss the changes that are observed in the 2024 IBC compared to its previous version in 2021. The effective site coefficients are presented for test site locations and their dependence on various factors including period, ground motion intensity, and regional models are discussed. Ratio maps between the new effective site coefficients and the old ones are then presented for soft site classes and for short and long periods. For soft site classes at short periods, the new effective site coefficients are lower than the old site coefficients for high seismicity regions and higher for low seismicity regions. As it was expected, for soft site classes at long periods and high seismicity regions, the new effective site coefficients are much larger than the old site coefficients without imposing the 50% increase as a penalty that was suggested in the 2021 IBC, whereas they could be much smaller if the 50% increase would have been imposed particularly around New Madrid and Charleston high seismicity regions. For low seismicity regions, the long period effective site coefficients can be smaller or larger by 20% compared to the 2021 IBC coefficients.

Conference Paper

Comparison of two approaches for determining ground-water discharge and pumpage in the lower Arkansas River Basin, Colorado, 1997-98

In March 1994, the Colorado Division of Water Resources (CDWR) adopted “Rules Governing the Measurement of Tributary Ground Water Diversions Located in the Arkansas River Basin” (Office of the State Engineer, 1994); these initial rules were amended in February 1996 (Office of the State Engineer, 1996). The amended rules require users of wells that divert tributary ground water to annually report the water pumped monthly by each well. The rules allow a well owner to report the pumpage measured by a totalizing flowmeter (TFM) or pumpage determined from electrical power data and a power conversion coefficient (PCC) (Hurr and Litke, 1989). Opinions by representatives of the State of Kansas, presented before the Special Master hearing a court case [State of Kansas v. State of Colorado, No. 105 Original (1996)] concerning post-Compact well pumping, stated that the PCC approach does not provide the same level of accuracy and reliability as a TFM when used to determine pumpage. In 1997, the U.S. Geological Survey (USGS), in cooperation with the CDWR, began a 2-year study to compare ground-water pumpage estimates made using the TFM and the PCC approaches. The study area was along the Arkansas River between Pueblo, Colorado, and the Colorado-Kansas State line (fig. 1). The two approaches for estimating ground-water discharge and pumpage were compared for more than 100 wells completed in the alluvial aquifer of the Arkansas River Basin. The TFM approach uses an inline flowmeter to directly measure instantaneous discharge and the total volume of water pumped at a well. The PCC approach uses electrical power consumption records and a power conversion coefficient to estimate the pumpage at ground-water wells. This executive summary describes the results of the comparison of the two approaches. Specifically, (1) the differences in instantaneous discharge measured with three portable flowmeters and measured with an inline TFM are evaluated, and the statistical differences in paired instantaneous discharge between the two approaches are determined; (2) short- and long-term variations in the PCC’s are presented; (3) differences in pumpage between the two approaches are evaluated, and the statistical differences in pumpage between the two approaches are determined; (4) potential sources of discrepancy between pumpage estimates are discussed; and (5) differences in total network pumpage using the two approaches are presented. During the irrigation seasons of 1997 and 1998, instantaneous discharge and electrical power demand were measured at randomly selected wells to determine PCC’s. At more than 100 wells, the PCC’s determined during the 1998 season were applied to total electrical power consumption data that was recorded between the initial and final readings at each network well site in 1998 to estimate total ground-water pumpage. At each site, an inline TFM was installed in a full-flowing, acceptable test section of pipe on the discharge side of the pump where the measurement of discharge was made. Measurements of instantaneous ground-water discharge also were made using three different types of portable flowmeters. The average velocity multiplied by the cross-sectional area of the discharge pipe was used to compute the discharge in gallons per minute. Whenever possible, discharge measurements were made at each network site using all three types of portable flowmeters.

Colorado

Reservoir evolution, downstream sediment transport, downstream channel change, and synthesis of geomorphic responses of Fall Creek and Middle Fork Willamette River to water years 2012–18 streambed drawdowns at Fall Creek Lake, Oregon

Executive Summary Chapter A. Introduction Fall Creek Dam impounds Fall Creek Lake, a 10-kilometer-long reservoir in western Oregon and is operated by the U.S. Army Corps of Engineers (USACE) primarily for flood-risk management (or flood control) in late autumn through early spring months, as well as for water quality, irrigation, recreation, and habitat in late spring through early autumn. Since 2011 (water year [WY] 2012), Fall Creek Lake has been temporarily drawn down each year to facilitate downstream passage of juvenile spring Chinook salmon ( Oncorhynchus tshawytscha ) through the 55-meter (m) high dam. This annual dam operation is temporary, typically lasting about 1–2 weeks from WY 2012 through 2020 (drawdown operations in WY 2022–24 have increased to more than 6 weeks). Drawdown of the reservoir results in lake levels being lowered to the elevation near the historical, pre-dam streambed. The annual streambed drawdowns of WY 2012–18 have improved fish passage and led the USACE to formally adopt streambed drawdowns as part of annual operations at Fall Creek Dam. However, temporarily lowering the lake to streambed creates free-flowing conditions in the reservoir that result in the erosion and episodic export of predominantly sand and finer-grained sediments (less than 2 millimeters [mm]) to the lower gravel-bed reaches of Fall Creek and the Middle Fork Willamette River. The introduction of large volumes of sand and finer-grain sediment into the dam-regulated reaches downstream from Fall Creek Dam prompted questions about the geomorphic responses to annual streambed drawdowns within Fall Creek Lake and downstream reaches along Fall Creek and the Middle Fork Willamette River. The U.S. Geological Survey (USGS) in partnership with USACE initiated a comprehensive geomorphic and sediment transport investigation to assess the coupled processes of reservoir erosion, sediment evacuation from Fall Creek Lake, and patterns of sediment transport and deposition in reaches downstream from the Fall Creek Dam that have resulted from annual streambed drawdowns. The purpose of this report is to systematically describe the processes of sediment erosion, transport, and deposition at Fall Creek Lake and geomorphic interactions between reaches upstream and downstream from Fall Creek Dam that relate to dam operations. Specifically, this report focuses on evaluating geomorphic responses to streambed drawdowns from WY 2012 through 2018 and placing drawdown-induced geomorphic responses within the broader context of physiographic and historical conditions and dam operations of Fall Creek and Middle Fork Willamette Rivers. Key objectives for this study were to characterize changes in reservoir morphology and substrate at Fall Creek Lake, describe the character and temporal pattern of sediment transport downstream from Fall Creek Dam, characterize geomorphic changes in channel reaches downstream from the Fall Creek Dam, and relate these data to the annual streambed drawdowns of WY 2012–18. This study uses multiple independent monitoring and measurement approaches to assess site, reach, and river-scale geomorphic responses to drawdowns to inform dam and reservoir management. Patterns and processes of reservoir evolution were assessed with geomorphic mapping and volumetric analyses of topography through comparison of multiple digital surface models (DSMs). Just downstream from Fall Creek Dam, analyses of sediment export from the reservoir focused on suspended sediment but also incorporated bedload analyses to assess sediment sizes. Geomorphic assessments downstream from the dam used reach-scale and site-scale approaches to document changes in channel morphology and substrate, including site measurements of sand and finer-grained sediment deposition and in-channel bed-material, volumetric change analyses from comparison of digital elevation models (DEMs), and repeat geomorphic mapping. Findings from this study inform river management and dam operations by providing an understanding of (1) coupled upstream-downstream geomorphic responses to the Fall Creek Lake streambed drawdowns, (2) geomorphic responses of Fall Creek Lake streambed drawdowns in comparison to drawdowns at other large dams, (3) controls on reservoir erosion and downstream geomorphic responses, and (4) implications for future hydrogeomorphic changes that may result from continued drawdowns and monitoring activities to assess those changes. Chapter B. Reservoir Morphology and Evolution Related to Dam Operations at Fall Creek Lake To understand the volume and distribution of sediment accumulation in Fall Creek Lake since dam closure in 1965, decadal-scale sedimentation patterns (spanning approximately 1965–2016) are evaluated using a combination of storage curve analyses and geomorphic mapping. Short-term (drawdown event-scale) patterns of erosion, sedimentation, and sediment export downstream are evaluated using a combination of geomorphic mapping and change detection analyses that quantify the distribution and total volume of sediment erosion and deposition within Fall Creek Lake. Geomorphic mapping of reservoir topography and analyses of historical datasets reveals four categories of landforms and sediment processes within Fall Creek Lake related to lake level operations: lacustrine sedimentation expressed in the reservoir floor, fluvial erosion and deposition within historical stream channels during streambed drawdowns, channel-like features created by erosion within the reservoir floor during streambed drawdowns, and erosion on reservoir hillslopes. Where the reservoir floor is mapped for this study as pelagic (deep water), deposition up to 3 meters (m) thick by lacustrine processes and burial of pre-dam topography with deposits thinning toward the edges of the valley floor and upstream areas of reservoir are observed. Despite over 50 years of sediment accumulation since dam construction, the main stream channels of Fall and Winberry Creeks (or reservoir thalwegs) through the reservoir are well defined, though their distinct morphology is likely influenced by a long history of recurring historical drawdowns to or near streambed since dam construction. Unregulated streamflow and sediment transport through the reservoir primarily are confined to these channels during the streambed drawdown periods. Erosional channel-like features created by drawdowns are carved through underlying, unconsolidated reservoir floor sediments and are most prominent in the lower reservoir below minimum conservation pool (the low pool elevation during winter flood season); sediment generated from the formation of these drawdown channels is more likely to be transported through and out of the reservoir than sediment deposits along the reservoir hillslopes at the valley margins that are separated from main channels by areas of low-gradient reservoir floor. Morphologic changes in the lower reservoir topography between January 2012 and November 2016 indicate overall net erosion of about 129,500 cubic meters (m 3 ). The most prominent geomorphic changes occurred along the main channels of Fall and Winberry Creeks near the Fall Creek Dam where incision, lateral migration, and slumping banks resulted in vertical and lateral adjustments to channel position, whereas most changes fell below the detectable limit on higher-elevation reservoir floor surfaces except where erosion occurred along features mapped as drawdown channels. Chapter C. Sediment Delivery from Fall Creek Lake and Transport through Downstream Reaches USGS implemented a sediment monitoring program in WY 2013–18 to evaluate the quantity and character of reservoir sediment exported from Fall Creek Lake during streambed drawdowns. Turbidity and suspended sediments were monitored annually autumn through spring to span the WY 2013–18 streambed drawdowns; however, unequal monitoring timeframes each year reduced the ability to compare results and factors affecting sediment export from the reservoir difficult between years. These data were originally measured to develop regressions and compute suspended-sediment loads (SSL). Bedload sediment monitoring from a cableway at the Fall Creek streamgage was completed in the autumn-winter of WY 2013 and 2017. The limited number of samples and presumed variability in sediment supply from the reservoir precluded construction of streamflow and bedload discharge relations to compute more than instantaneous bedload. Sand and finer-grained silts and clays were transported from the reservoir in suspension, though some coarser grains (up to 32 mm) were also mobilized and transported downstream from the dam as bedload. Observations of increased sediment transport downstream from Fall Creek Dam coincided with lake levels approaching about 3 m (10 feet [ft] or elevation 690 ft) above the streambed regulating outlets. Suspended-sediment loads computed for the full monitoring periods WY 2013–18 at the Fall Creek streamgage, located 1.4 kilometers (km) downstream from Fall Creek Dam, range from 54,700 metric tons (t) in WY 2013 to 13,900 t in WY 2018. Although the total annual SSL varied from year to year, the overall seasonal patterns of suspended sediment transport throughout each year were similar during monitoring in WY 2013-18. Suspended-sediment loads were low prior to the drawdown, then increased rapidly as lake levels lowered and approached the streambed. In the weeks following the drawdown period, as pool levels were increased, SSL remained slightly elevated above pre-drawdown levels but generally declined through the following winter and spring except during streamflow-driven pulses of suspended-sediment transport. WY 2013 had the greatest total computed SSL for each streambed drawdown and partial-year monitoring period. SSL computed for the partial-year period have generally decreased since WY 2013 and have varied by about 6,800 t with the exception of WY 2014. WY 2014 SSL reflects anomalously low sediment export due to low streamflows and freezing conditions that stabilized reservoir floor deposits. Bedload measurements in the short 1.4-km reach between Fall Creek Dam and the Fall Creek streamgage showed an inverse correlation between bedload transport rates and discharge, which probably reflects diminishing supply of coarse-sized sediment. Sand was more abundant (60–100 percent) than gravel in bedload samples confirming sand and finer-grained sediment dominated sediment evacuated from the reservoir during streambed drawdowns at Fall Creek Lake. Chapter D. Geomorphic Responses to Fall Creek Lake Streambed Drawdowns Downstream from Fall Creek Dam In the days, weeks, and months following streambed drawdown operations at Fall Creek Dam through WY 2018, sites downstream from the dam displayed a variety of geomorphic responses to reservoir sediment delivery within the main channel and overbank areas. Evaluation of streambed elevations at two streamgages located 1.4 km downstream from the dam on Fall Creek and 16.3 km downstream from the dam on the Middle Fork Willamette River indicated the effects of drawdown sediment on bed elevations were modest and transient. Repeat particle size measurements (October 2015 and September 2016) at five sites along Fall Creek and the Middle Fork Willamette River showed similar grain-sized distributions that do not reveal substantial deposition of fine-grained sediment related to the WY 2016 streambed drawdown. Altogether, these findings indicate that transport capacity in the main, low-flow channels of Fall Creek and Middle Fork Willamette River during WY 2012–18 was sufficient to mobilize and evacuate reservoir sediments from streambed drawdowns or other bank material and tributary sources. However, other monitoring for this study indicate low-velocity zones in off-channel areas are prime locations for sand and finer-grain sediment deposition. Patterns of overbank sediment accumulation indicate that the magnitude and timing of overbank deposition on bars and low-elevation floodplain varies with proximity to the dam, geomorphic setting, streamflows, and other factors. Sand and finer-grained reservoir sediments carried as suspended-sediment load in the reaches downstream from Fall Creek Dam were deposited in overbank areas as observed with clay-horizon markers during WY 2016–17. Overbank deposition quantified with Geomorphic Change Detection (GCD) software evaluated landform-scale patterns of erosion and deposition using repeat light detection and ranging (lidar) surveys at two sites in the Upper Fall Creek reach and one site in the Jasper reach for 3 years (2012–15) and one site in the Clearwater reach for 6 years (2009–15). Deposition thickness and spatial patterns from the GCD analysis were variable; some sites had dispersed but measurable deposition while at others, deposition was highly localized and exceeded 1 m in depth. Patterns of overbank deposition illustrate interactions among bar morphology, local hydraulics, and suspended-sediment transport dynamics that can create patches of highly localized deposition. The measured deposition at the two Fall Creek GCD sites likely resulted from reservoir sediments released from Fall Creek Lake during streambed drawdowns in WY 2016 and 2017 because the limited sediment inputs from bank material (geomorphically laterally stable reach) or tributaries (no significant tributaries) provided few other sediment sources. On the Middle Fork Willamette River, observed patterns of overbank deposition could reflect sediment sourced from upstream tributaries, bank erosion, or Fall Creek Lake streambed drawdown operations. Despite the introduction of several thousand tons of reservoir sediment delivered from the Fall Creek Lake streambed drawdowns to below-dam river corridors, reach-scale mapping of channel features downstream from Fall Creek Dam shows minimal evidence of changes in channel planform or landforms that can be attributed to a drawdowns in WY 2012–16. On Upper Fall Creek reach, widespread increases in gravel bars or other in-channel sediment did not result from the five streambed drawdowns. The main changes attributable to sediment releases from Fall Creek Lake were localized increases in vegetated bar area, particularly on channel margin areas where sand and finer-grain sediment was deposited and rapidly colonized by vegetation. The area of mapped secondary water features decreased between 2005 and 2016, but that may be due to lower discharges depicted in the 2016 aerial photographs and less mapped area of inundation. Primary changes along the Lower Fall Creek reach include a 6.4 percent decrease in area of secondary water features between 2011 and 2016, and a nearly twofold increase in the area of unvegetated bars. Immediately downstream from the Fall Creek confluence, there were negligible changes in the location and areas of vegetated bars and the main wetted channel between 2005 and 2016, and local increases in bar area cannot be attributed solely to deposition of reservoir sediments from Fall Creek Lake because (1) areas along the Middle Fork Willamette River just upstream from the Fall Creek confluence display similar type and magnitude of changes and (2) some of the increases at the confluence area pre-date the drawdowns. The cumulative effect of sediment releases from Fall Creek Lake streambed drawdowns from WY 2012 to 2016 on downstream channel planform and landforms are modest compared to the river-scale transformations and planform changes that occurred in the decades following dam construction. Chapter E. Discussion of Geomorphic Responses of Fall Creek and Middle Fork Willamette River to Streambed Drawdowns at Fall Creek Lake Multiple aspects of Fall Creek Dam infrastructure and operations exert first-order controls on the magnitudes of reservoir erosion that occur during the streambed drawdowns and ultimately determine the sediment delivery to downstream reaches. Key aspects of the dam and its operations that are most relevant to assessing geomorphic responses to streambed drawdowns include the (1) dam infrastructure, including configuration and size of regulating outlets and their proximity to the streambed which dictates the capacity and competence of the river to deliver sediment to downstream reaches and mode of sediment transport as suspended-sediment load or bedload; (2) frequency of historical drawdowns and long-term, year-round dam operations and lake level management, which partly dictate reservoir morphology and locations and magnitudes of readily erodible materials; (3) dam operations and hydroclimatic conditions during the streambed drawdown (including length of the drawdown and streamflows entering the reservoir), which directly control the timing, duration and magnitude of reservoir erosion and sediment evacuation; and (4) dam operations following the streambed drawdown operation that regulate streamflows (and thereby sediment transport conditions) downstream of Fall Creek Dam which primarily reflect interactions between hydroclimatic conditions and flood control operations. Patterns of sediment erosion and evacuation observed in this study at Fall Creek Lake from WY 2012–18 suggest that reservoir erosion during annual streambed drawdowns may remain similar or decrease in future years assuming (1) annual streambed drawdown operations are implemented in similar manner as the WY 2012–18 drawdowns (in terms of duration, late autumn or early winter implementation, rate of pool-level lowering to reach streambed, and other factors), (2) streambed drawdowns coincide with similar conditions as were observed WY 2012–18 (similar sediment yield into reservoir, low reservoir inflows, limited precipitation, moderate air temperature), and (3) no major geomorphic changes in the main reservoir channels of Fall and Winberry Creeks occur (for example, channel avulsion). Under such conditions, it is hypothesized that the stream channel within the reservoir would achieve a quasi-equilibrium state with respect to annual influx and export of sediment and aided by the substantial amount of in-channel bedrock, will remain laterally stable without erosion across reservoir deposits. Patterns of sediment transport measured at the Fall Creek streamgage downstream from Fall Creek Dam provide insight into the potential effects of future streambed drawdowns at Fall Creek Lake. Analyses of suspended sediment measured in WY 2013–18 show a major reduction in suspended-sediment loads between WY 2013 and later years, indicating streamflows transporting sediment through the reservoir to downstream reaches during streambed drawdowns have become supply limited. The 6-year suspended-sediment monitoring and sampling program is insufficient to make predictions about future sediment transport conditions because of uneven monitoring periods and varying controls on reservoir sediment erosion. It is likely that future suspended-sediment loads will be variable but similar to those observed in WY 2015–18 if operational, climatic, and geomorphological factors remain similar to those monitored WY 2015–18. Suspended-sediment loads downstream from Fall Creek Lake will likely remain highest when regulating outlets are fully open and Fall Creek is free flowing with the reservoir fully drained with little to no residual pool. Over time, it is possible that the suspended-sediment loads would reflect mobilization of reservoir sediment deposited in the previous year rather than erosion of sediment deposited years or decades earlier. Bedload is likely to remain a small fraction of the total sediment load evacuated from the reservoir and is relatively modest compared with pre-dam bedload transport rates because most coarse sediment remains trapped by the dam. If sediment releases from Fall Creek Lake and ensuing streamflow conditions follow a similar pattern in the future as was assessed in this study spanning WY 2012–18, near-term geomorphic adjustments downstream of the dam are expected to be modest. Barring major operational, climatic, and geomorphological changes, local site-scale deposition on bars, overbank areas, or off-channel features that persists several months after the streambed drawdown will likely continue to be highly variable, ranging from negligible to several centimeters of deposition. At the landform-scale, low velocity areas nearest to Fall Creek Dam will likely continue to undergo rapid deposition immediately during and after a streambed drawdown event, similar to patterns observed for WY 2012–18. Some of the sediment entering these off-channel features and margin areas may be temporarily stored, then later remobilized and dispersed farther downstream. But if newly deposited sediment persists through the following spring, there is a greater likelihood that local vegetation will establish, reinforce deposited material, and trap sediment during later drawdowns. The reach-scale geomorphic changes may become more apparent if (1) streambed drawdowns continued for several decades, and geomorphic changes were measured at decadal scales or (2) the amount of sediment introduced to downstream reaches substantially increased and (or) sediment transport capacity decreased. The continued streamflow regulation of Fall Creek Dam after sediment releases provides an opportunity to strategically manage streamflows during and after the streambed drawdowns to minimize downstream sediment impacts and ensure other operational thresholds are satisfied. This study provides a comprehensive foundation of datasets and geomorphic analyses to inform dam operations at Fall Creek Lake, monitor sediment transport downstream, and consider operational schemes for future drawdowns. The datasets from this study also provide baselines of sediment transport and geomorphic conditions to assess future changes in reservoir and downstream environments. Future monitoring could be tailored to address specific questions regarding the long-term geomorphic effects of streambed drawdowns on fluvial habitats, flood hazards, cultural resources, or downstream water quality. Future monitoring activities could focus on the relevant geomorphic processes and spatial domains within the three categories used for this study: (1) reservoir erosion and net sediment evacuation, (2) sediment delivery to downstream reaches, including magnitude and temporal pattern of sediment transport, and (3) geomorphic responses of downstream reaches to sediment delivery. Specifically, high priority future monitoring activities could include: Repeat topographic or photographic surveys in the reservoir to characterize changes occurring within individual drawdowns, to quantify sediment export, to determine temporal changes in reservoir storage, and to identify locations of erosion and deposition. Continuous, year-round turbidity monitoring supplemented with suspended-sediment measurements at a streamflow-gaging station immediately downstream from the dam to quantify sediment export. Repeat geomorphic monitoring, mapping, or modeling in downstream reaches to track changes in channel and over bank features using a combination of site- and reach-scale monitoring approaches. This could support assessments of sediment deposition and ensuing vegetation encroachment on flood hazards and habitats and examine how sediment transport and depositional processes may be affected by different sediment supply, streamflow, or dam management scenarios.

Oregon

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri and Mississippi Rivers on the periphery of Missouri, June 13–22, 2022

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near seven bridges at six highway crossings of the Missouri and Mississippi Rivers on the periphery of Missouri from June 13–22, 2022. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 feet longitudinally and generally extending laterally across the active channel from bank to bank during minor flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a minor flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All bridge sites in this study were surveyed and documented in previous studies. Although partial exposure of substructural support elements was observed at several piers, at most sites the exposure most likely is minimal compared to the overall substructure that remains buried in bed material at these piers. The notable exceptions are piers 12 and 13 at structure L0135 on State Highway 51 at Chester, Illinois, where the bedrock material was fully exposed around the piers. The average difference between the bathymetric surfaces between 2022 and 2018 varied from 0.41 foot higher to 1.86 feet lower. Between 2022 and 2014, the average difference between the bathymetric surfaces varied from 1.02 feet higher to 4.69 feet lower. Only the two sites on the Missouri River and the Caruthersville site were surveyed in 2011; for those sites, the average difference between the bathymetric surfaces varied from 5.83 feet higher to 1.34 feet lower. The most substantial overall net gain of sediment in a reach was between 2011 and 2022 at structure A1700 near Caruthersville, Mo. (site 38). This result was expected because structure A1700 is downstream from the confluences of the Missouri and Ohio Rivers, and therefore subject to the largest streamflows, the largest streamflow fluctuations, and the most substantial sediment flux, as has historically been observed at this site. The presence of riprap blankets, pier size and nose shape, and alignment to flow had a substantial effect on the size of the scour hole observed for a given pier. Piers that were surrounded by riprap blankets had scour holes that were substantially smaller (to nonexistent) compared to piers at which no rock or riprap were present. New riprap blankets were surveyed at pier 3 of structure L0098 at Brownville, Nebraska, and at piers 15–18 of structure A1700 near Caruthersville, Mo., that effectively mitigated the scour holes historically observed at these piers. Narrow piers having round or sharp noses that were aligned with flow often had scour holes that were difficult to discern from nearby bed features, whereas piers having wide or blunt noses resulted in larger, deeper scour holes. Several of the structures had piers that were skewed to primary approach flow. Scour holes near these piers consistently displayed greater depth on the side of the pier with impinging flow and deposition on the leeward side of the pier.

Missouri

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri River between Kansas City and St. Louis, Missouri, May 19–26, 2021

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near nine bridges at eight highway crossings of the Missouri River between Kansas City and St. Louis, Missouri, from May 19 to 26, 2021. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 to 1,840 feet (ft) longitudinally and generally extending laterally across the active channel from bank to bank during low to moderate flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a low to moderate flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All the bridge sites in this study were previously surveyed and documented in previous studies. Comparisons between bathymetric surfaces from the previous surveys and those of the current (2021) study do not indicate any consistent correlation between channel-bed elevations and streamflow conditions. The average difference between the bathymetric surfaces varied from 1.59 ft higher to 0.95 ft lower in 2021 than 2017, which corresponds to a gain of 100,200 cubic yards and a loss of 55,800 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 2.74 ft higher to 3.05 ft lower in 2021 than 2013, which corresponds to a gain of 111,500 cubic yards and a loss of 169,200 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 4.52 ft higher to 1.38 ft lower in 2021 than 2011, which corresponds to a gain of 221,100 cubic yards and a loss of 90,300 cubic yards, respectively. The most substantial overall net gain was 221,100 cubic yards between 2011 and 2021 at structures L0550 and A4497 at Jefferson City (site 20). The large net gain likely results from a combination of the mitigation of the scour holes near pier 4 of both bridges and the substantially lower flow in 2021 than in 2011. Alternatively, the most substantial overall net loss was 169,200 cubic yards between 2013 and 2021 at structure A6288 at Hermann (site 21), despite comparable streamflows. Pier size, nose shape, and skew to approach flow had a substantial effect on the size of the scour hole observed at a given pier. Larger and deeper scour holes were present at piers with wide or blunt noses caused by exposed footings or caissons. When a pier was skewed to primary approach flow, the scour hole was generally deeper and larger than at a similar pier without skew; furthermore, the shape of the scour hole near skewed piers in this study generally was longer and deeper on the side with impinging flow. At structure A6288 at Hermann (site 21), the scour hole near pier 5 was difficult to discern from nearby dunes and ripples, whereas the upstream edge of the footing was visible at pier 4, which likely contributes to the larger scour hole near that pier; the top of the footing may blunt the horseshoe vortex at pier 5, but the exposed front of the footing may exacerbate the vortex at pier 4.

Missouri

Regional evaluation of evapotranspiration in the Everglades

Nine sites in the Florida Everglades were selected and instrumented for collection of data necessary for evapotranspiration-determination using the Bowen-ratio energy-budget method. The sites were selected to represent the sawgrass or cattail marshes, wet prairie, and open-water areas that constitute most of the natural Everglades system. At each site, measurements necessary for evapotranspiration (ET) calculation and modeling were automatically made and stored on-site at 15- or 30-minute intervals. Data collected included air temperature and humidity at two heights, wind speed and direction, incoming solar radiation, net solar radiation, water level and temperature, soil moisture content, soil temperature, soil heat flux, and rainfall. Data summarized in this report were collected from January 1996 through December 1997, and the development of site-specific and regional models of ET for this period is described. Latent heat flux is the energy flux density equivalent of the ET rate. Modified Priestley-Taylor models of latent heat flux as a function of selected independent variables were developed at each site. These models were used to fill in periods of missing latent heat flux measurement, and to develop regional models of the entire Everglades region. The regional models may be used to estimate ET in wet prairie, sawgrass or cattail marsh, and open-water portions of the natural Everglades system. The models are not applicable to forested areas or to the brackish areas adjacent to Florida Bay. Two types of regional models were developed. One type of model uses measurements of available energy at a site, together with incoming solar energy and water depth, to estimate hourly ET. This available-energy model requires site data for net radiation, water heat storage, and soil heat flux, as well as data for incoming solar radiation and water depth. The other type of model requires only incoming solar energy, air temperature, and water depth data to provide estimates of hourly ET. The second model thus uses data that are more readily available than the data required for the available-energy model. Computed ET mean annual totals for all nine sites for the 1996-97 period ranged from 42.4 inches per year at a site where the water level is below land surface for several months each year to 57.4 inches per year at an open-water site with no emergent vegetation. Although the density of photosynthetically-active plant leaves has been shown to relate directly to ET in some studies, it does not appear to relate directly to ET in the Everglades, based on comparison of annual ET data with leaf-area index, defined as the Normalized Difference Vegetation Index (NDVI), data from satellite imagery. NDVI and ET appear to be inversely related in the Everglades. The greatest ET rates occurred at open-water sites where the NDVI data indicated the lowest leaf-area index. Among the remaining vegetated sites, there is no clear relation between ET and NDVI, though the highest ET rate corresponded to the lowest NDVI and one of the lowest ET rates corresponded to the highest NDVI value. The variation in ET follows a seasonal pattern, with lowest monthly ET totals occurring in December through February, and highest ET occurring in May through August. The greatest range in monthly ET among all nine sites for the 2-year period occurred at site 3: from 1.81 inches in December 1997 to 6.84 inches in July 1996. A study to compare the Bowen-ratio/energy balance method of ET measurement with the eddy-correlation method was done at one site from June 22, 1998, through September 28, 1998. This comparison indicated that both methods gave comparable values of the Bowen ratio, but there was a considerable difference in available energy measured by the two methods. The mean of all 30-minute measured turbulent heat fluxes from the eddy-correlation apparatus for June 22 through September 29, 1998, was 137.4 watts per square meter, and the mean of the corresponding measured energy was 163.6 watts per square meter, or about 20 percent greater. The disagreement in mean energy fluxes measured by the two methods is problematical and is not fully understood. Although the difference seems to be related to friction velocity, and is practically non-existent at values of friction velocity greater than 0.3 meter per second, the "correctness" of either method cannot be determined with the data available.

Florida