Geology Reports⌕ Search

USGS · sir20175028

Geophysics- and geochemistry-based assessment of the geochemical characteristics and groundwater-flow system of the U.S. part of the Mesilla Basin/Conejos-Médanos aquifer system in Doña Ana County, New Mexico, and El Paso County, Texas, 2010–12

Abstract

One of the largest rechargeable groundwater systems by total available volume in the Rio Grande/Río Bravo Basin (hereinafter referred to as the “Rio Grande”) region of the United States and Mexico, the Mesilla Basin/Conejos-Médanos aquifer system, supplies water for irrigation as well as for cities of El Paso, Texas; Las Cruces, New Mexico; and Ciudad Juárez, Chihuahua, Mexico. The U.S. Geological Survey in cooperation with the Bureau of Reclamation assessed the groundwater resources in the Mesilla Basin and surrounding areas in Doña Ana County, N. Mex., and El Paso County, Tex., by using a combination of geophysical and geochemical methods. The study area consists of approximately 1,400 square miles in Doña Ana County, N. Mex., and 100 square miles in El Paso County, Tex. The Mesilla Basin composes most of the study area and can be divided into three parts: the Mesilla Valley, the West Mesa, and the East Bench. The Mesilla Valley is the part of the Mesilla Basin that was incised by the Rio Grande between Selden Canyon to the north and by a narrow valley (about 4 miles wide) to the southeast near El Paso, Tex., named the Paso del Norte, which is sometimes referred to in the literature as the “El Paso Narrows.” Previously published geophysical data for the study area were compiled and these data were augmented by collecting additional geophysical and geochemical data. Geophysical resistivity measurements from previously published helicopter frequency domain electromagnetic data, previously published direct-current resistivity soundings, and newly collected (2012) time-domain electromagnetic soundings were used in the study to detect spatial changes in the electrical properties of the subsurface, which reflect changes that occur within the hydrogeology. The geochemistry of the groundwater system was evaluated by analyzing groundwater samples collected in November 2010 for physicochemical properties, major ions, trace elements, nutrients, pesticides (reported but not used in the assessment), and environmental tracers. The data obtained from these samples (with the exception of the pesticide data) were used to gain insights into processes controlling the groundwater movement through the groundwater system in the study area. Results from the geophysical and geochemical assessments facilitated the interpretation of the geochemical characteristics of the groundwater sources and geochemical groups within the groundwater system. The groundwater-flow system in the study area consists primarily of the Mesilla Basin aquifer system, which can be divided into four hydrogeologic units by using an informal classification scheme based on basin-fill stratigraphy and sedimentology with an emphasis on aquifer characteristics. The four hydrogeologic units are (1) the Rio Grande alluvium, which is the shallow aquifer of the Mesilla Basin within the confines of the Mesilla Valley, and the three hydrogeologic units that compose the Santa Fe Group: (2) the lower part of the Santa Fe Group, which is the least productive zone, (3) the middle part of the Santa Fe Group, which is the primary water-bearing hydrogeologic unit in the basin and is generally saturated, and (4) the upper part of the Santa Fe Group, which is the most productive water-bearing unit within the Santa Fe Group but is only partially saturated in the north and largely unsaturated in the south and western parts of the Mesilla Basin. The helicopter frequency domain electromagnetic survey results indicated that approximately half of the resistivity values were less than 10 ohm-meters at depths of 50 and 100 feet with a transition where the resistivity values changed from relatively high values (greater than 20 ohm-meters) to relatively low resistivity values (less than 10 ohm-meters) near Vado, New Mexico. Slightly more than 25 percent of the gridded resistivity values from the three-dimensional grid of the combined inverse modeling results of the direct-current resistivity and time-domain electromagnetic soundings were equal to or less than 10 ohm-meters with large regions of low resistivity becoming apparent in the southernmost part of the study area near the Paso Del Norte where these low resistivity features are spatially the widest at or below the top of the bedrock. These low resistivity values might represent clayey deposits, sediments composed largely of sand and gravel saturated with saline water, or both. Historical dissolved-solids-concentration data within the surface geophysical subset area of the study area were compiled and compared to the inverse modeling results of the combined direct-current resistivity and time-domain soundings; this comparison was done to strengthen the interpretation made from the combined inverse modeling results that the low resistivity features were representative of sand and gravel deposits saturated with saline water and not clayey deposits. Water-level altitudes within the Rio Grande alluvium generally decreased from north to south, with a west to east decrease in water-level altitudes near Las Cruces, New Mexico, as a result of groundwater pumping. Groundwater flow within the Santa Fe Group is more complex than the groundwater flow within the Rio Grande alluvium because of the larger lateral and vertical extent of the Santa Fe Group compared to the Rio Grande alluvium. Groundwater from the Organ Mountains flows directly south towards the Paso del Norte. Groundwater from the Robledo Mountains, the Rough and Ready Hills, and the Sleeping Lady Hills generally flows to the southeast. Groundwater flowing near the north end of the midbasin uplift generally continues east towards the Rio Grande and then flows south on the east side of the midbasin uplift. Groundwater flowing near the west side of the midbasin uplift generally continues south parallel to the faults that make up the midbasin uplift and then flows east towards the Paso del Norte when it reaches the south end of the midbasin uplift. Groundwater from the Aden Hills and the East and West Potrillo Mountains flows to the south end of the midbasin uplift and then continues east towards the Paso del Norte. Throughout most of the Mesilla Valley, the vertical hydraulic gradient was downward because the water-level altitude in the Rio Grande alluvium was higher than it was in the Santa Fe Group, but in some areas (typically in the middle and southern parts of the Mesilla Valley), the vertical hydraulic gradient was substantially reduced or even reversed to an upward hydraulic gradient. The geochemistry data indicate that there was a complex system of multiple geochemical endmembers and mixing between these endmembers with recharge to the Rio Grande alluvium and Santa Fe Group composed mostly of seepage from the Rio Grande, inflows from deeper or neighboring water systems, and mountain-front recharge. Five distinct geochemical groups were identified in the Mesilla Basin study area: (1) ancestral Rio Grande (pre-Pleistocene) geochemical group, (2) modern Rio Grande (Pleistocene to present) geochemical group, (3) mountain-front geochemical group, (4) deep groundwater upwelling geochemical group, and (5) unknown freshwater geochemical group. The ancestral Rio Grande groundwater was water that recharged into the system as seepage losses from the ancestral Rio Grande; this groundwater generally flows from north to south-southeast towards the Paso del Norte. Groundwater on the west side of the midbasin uplift generally flows south until it reaches the southern part of the study area; from the southern part of the study area, the groundwater flows east towards the Paso del Norte. Groundwater on the east side of the midbasin uplift flows south-southeast towards the Paso del Norte where it mixes with groundwater from the modern Rio Grande, uplifted areas in the west, and the deep saline source. The water type of the modern Rio Grande geochemical group ranged from calcium-sulfate water type in the northern part of the study area to sodium-chloride-sulfate water type in the southern part of the study area; from north to south there was a substantial increase in specific conductance, strontium-87/strontium-86 ratio, potassium, and the trace metals of iron and lithium, changing the water chemistry such that it became similar to the water chemistry of the deep groundwater upwelling geochemical group. From age-dating results, water in the modern Rio Grande geochemical group was recharged to the Rio Grande alluvium within the past 10 years. The mountain-front geochemical group was generally old water (apparent age was greater than 10,000 carbon-14 years before present) that was somewhat mineralized and has relatively high concentrations of fluoride and silica, which might indicate longer exposure to volcanic and siliciclastic rocks or aluminosilicate minerals. There were five different locations of recharge determined from the groundwater geochemistry within the mountain-front geochemical group, all having a slightly different geochemical signature: (1) the Rough and Ready Hills, Robledo Mountains, and the Sleeping Lady Hills, (2) the Doña Ana Mountains, (3) the Aden Hills and West Potrillo Mountains, (4) the East Potrillo Mountains, and (5) the Sierra Juárez in Mexico. The groundwater from the Rough and Ready Hills, Robledo Mountains, the Sleeping Lady Hills, and the Doña Ana Mountains generally flows toward the Rio Grande and eventually mixes together and with the modern Rio Grande groundwater. The groundwater originating from the Aden Hills and East and West Potrillo Mountains generally flows east to southeast at a slow rate and eventually mixes and continues east, where it mixes with groundwater from the ancestral Rio Grande geochemical group and with the groundwater from the Sierra Juárez. The groundwater from the Sierra Juárez flows north and then east towards the Paso del Norte where it mixes with groundwater from the uplifted areas in the west, ancestral and modern Rio Grande groundwater, and the upwelling groundwater from a deep saline source. The deep groundwater upwelling geochemical group had the highest concentrations of bicarbonate, potassium, silica, aluminum, iron, and lithium within the study area, indicating that it had been in contact with carbonate and siliciclastic rocks for a much longer period of time and at higher temperatures compared to the other geochemical groups, and was most likely ancient marine groundwater originating from the Paleozoic and Cretaceous carbonate rocks which was upwelling into the Mesilla Basin aquifer system in the southeastern part of the study area through the extensive fault systems. Direct-current resistivity and time-domain electromagnetic soundings support the interpretation of ancient marine groundwater upwelling into the Mesilla Basin aquifer system, as do the analytical results from wells, and the helicopter frequency domain electromagnetic data collected along the Rio Grande. The hydrogen-2/hydrogen-1 ratio and oxygen-18/oxygen-16 ratio isotopic results for samples in the unknown freshwater geochemical group did not plot on the Rio Grande evaporation line, indicating this group did not have a Rio Grande signature (that is, there was no isotopic evidence of a component of Rio Grande water) and it also had the lowest mineralized content of any geochemical group in the study area.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 31.65° to 32.625° latitude; -107.25° to -106.375° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Andrew P. Teeple. 2017-06-16. Geophysics- and geochemistry-based assessment of the geochemical characteristics and groundwater-flow system of the U.S. part of the Mesilla Basin/Conejos-Médanos aquifer system in Doña Ana County, New Mexico, and El Paso County, Texas, 2010–12. https://doi.org/10.3133/sir20175028

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Evaluating the number of realizations (train-test splits) necessary to ensure robust estimates of conventional hydrothermal resource favorability using Monte Carlo cross-validation, the Great Basin, Western USA

Supervised machine learning approaches used to produce favorability maps in resource assessments commonly partition an input dataset into training and testing subsets (that is, through train-test splits). However, if a single split is not representative of underlying resource conditions, the resulting favorability map may be biased, particularly with sparse or heterogeneous datasets. To mitigate the potential for unrepresentative favorability maps, recent works by U.S. Geological Survey researchers have used Monte Carlo cross-validation to implement a large number ( n) of randomized train-test splits to produce n realizations. The realizations are then aggregated using cell-wise median predictions to produce the resulting final favorability map, recognizing that the median will remove extreme values that might have been estimated from a comparatively few unrepresentative realizations. Theoretically, the median prediction at every cell converges to a single estimate as n approaches infinity, and the question addressed herein is: How many realizations are necessary to get a robust estimate (that is, an estimate unaffected by additional realizations)? Therefore, convergence metrics are described to identify the number of train-test splits and realizations needed to make a reliable map using the data and supervised machine learning workflow for conventional hydrothermal resource assessment of the Great Basin of the Western United States. For this study, robust prediction occurs with n approximately equal to 600 realizations, and smaller ensembles (for example, n is approximately equal to 200 or even 100) may be suitable during preliminary or exploratory analyses. Although the resulting threshold numbers will vary depending on the data and modeling approach used, the convergence metrics proposed and applied herein are applicable to other supervised machine learning studies that use Monte Carlo cross-validation.

Scientific Investigations Report↗

Groundwater budget for the Portneuf River Basin, southeastern Idaho

The U.S. Geological Survey, in cooperation with the Idaho Department of Water Resources, developed the first groundwater budget for the upper Portneuf River Basin in southeastern Idaho, a tributary of the Snake River. A groundwater budget for the Portneuf River Basin supports water resource and administrative management decisions within the basin and for downstream users of the eastern Snake River Plain aquifer. The analysis quantifies inflows, outflows, and residuals for an aquifer system defined by the Idaho Department of Water Resources under three recent precipitation conditions: an average year (2016), a dry year (2021), and a wet year (2023). The budget was calculated for the basin and for two subbasins delineated by the U.S. Geological Survey streamgage Portneuf River at Topaz, Idaho (13073000): the above Topaz subbasin, which includes the Portneuf-Gem valley, and the below Topaz subbasin, which includes Marsh Valley. Aquifer inflows include mountain-front recharge; areal recharge; recharge from applied water, including recharge from irrigation, canal seepage, and effluent returns; groundwater flow into the basin; and reservoir seepage. Outflows include groundwater pumping for agricultural, municipal, and domestic uses; subsurface outflow through the Portneuf gap; and discharge to streams as base flow. Estimated annual inflows for the full basin ranged from 116,880 acre-feet in 2021 to 154,880 acre-feet in 2023, and outflows ranged from 132,190 acre-feet in 2016 to 158,490 acre-feet in 2023. Basinwide residuals, the change in storage plus uncertainty, were −2,410 acre-feet in 2016, −18,410 acre-feet in 2021, and −3,610 acre-feet in 2023, and each subbasin had a mixture of negative and positive residuals. These basinwide results, interpreted as change in storage plus water-budget uncertainty, indicate minor net losses that increase with dry conditions, consistent with well depth-to-water measurements indicating gradual multi-decadal declines. Patterns in subbasin residuals are driven by irrigation practices and surface-water management; for example, the above Topaz subbasin relies more on groundwater for irrigation, resulting in more negative residuals during dry years. In contrast, the below Topaz subbasin depends more on surface water, producing positive residuals during dry years because of irrigation losses and canal seepage. The analyses for both subbasins indicate decades-long groundwater declines, which agree with the overall negative residuals calculated. The largest sources of uncertainty include climate inputs (precipitation and evapotranspiration) and poorly constrained components such as groundwater inflow and tributary stream infiltration. These findings provide insight into how climatic variables and irrigation practices affect groundwater inflows and outflows within the Portneuf River Basin.

Idaho↗

World minerals outlook—Antimony, copper, graphite, niobium, potash, silicon, silver, and tungsten through 2030

Demand for mineral commodities continues to increase owing to rapid technological advancements and global economic growth. To support this increase in demand, information about current and near-term supplies of these mineral commodities is essential. Such data help evaluate the health and stability of global supply chains and protect against potential supply risks. Current production and production capacity data coupled with information regarding near-term expected changes (such as facility closures, planned expansions, or the completion of new mineral production projects) can provide insight into expected future market developments and expected available supply of mineral commodities. This report within the “World Minerals Outlook” series analyzes data for antimony, copper, natural graphite, niobium, potash, silicon metal, silver, and tungsten—eight mineral commodities listed in the 2025 List of Critical Minerals. World production data from 2019 through 2025, as well as estimated world capacity data from 2023 through 2025 were analyzed. Using these data, near-term (2026–2030) expected world capacities were estimated. For antimony, copper, niobium, silicon metal, silver, and tungsten, modest increases in production capacity of 4 to 10 percent were expected between 2025 and 2030, whereas capacities for natural graphite and potash were expected to increase by about 18 to 20 percent.

Scientific Investigations Report↗