Aftershocks preferentially occur in previously active areas

Morgan T. Page; Nicholas van der Elst

doi:10.1785/0320220005

Home/Archive/USGS

USGS · 70231607

Aftershocks preferentially occur in previously active areas

Morgan T. Page·Nicholas van der Elst

View original source ↗Export metadata ↓

Abstract

The clearest statistical signal in aftershock locations is that most aftershocks occur close to their mainshocks. More precisely, aftershocks are triggered at distances following a power‐law decay in distance ( Felzer and Brodsky, 2006 ). This distance decay kernel is used in epidemic‐type aftershock sequence (ETAS) modeling and is typically assumed to be isotropic, even though individual sequences show more clustered aftershock occurrence. The assumption of spatially isotropic triggering kernels can impact the estimation of ETAS parameters themselves, such as biasing the magnitude‐productivity term, alpha, and assigning too much weight to secondary rather than primary (direct) triggering. Here we show that aftershock locations in southern California, at all mainshock–aftershock distances, preferentially occur in the areas of previous seismicity. For a given sequence, the scaling between aftershock rates and the previous seismicity rate is approximately linear. However, the total number of aftershocks observed for a given sequence is independent of background rate. We explain both of these observations within the framework of rate‐and‐state friction ( Dieterich, 1994 ).

Explore related subjects

The Seismic Record Article

Source-reported bounding extent: 32.62087018318113° to 38.22091976683121° latitude; -122.54150390625° to -114.14794921875° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Morgan T. Page, Nicholas van der Elst. 2022-04-29. Aftershocks preferentially occur in previously active areas. https://doi.org/10.1785/0320220005

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Only very strong shaking can break a tree

A handful of credible accounts, both recent and historical, describe trees being broken during earthquakes. Apart from landslides and tsunamis, such accounts are uncommon, suggesting that trees break only when ground acceleration is extreme or when trees are especially vulnerable to breakage. Here, I consider the question: what ground acceleration is required to break a living tree? I present simplified first‐principles calculations, considering the properties of common trees, focusing on tall, thin trees that can be approximated as uniform vertical cantilevers. The results suggest that, possibly excepting tall trees with heavy canopies, standing trees can only be broken by shaking approaching or exceeding 1 g , as anticipated by the rarity of documented accounts of snapped trees. I briefly consider several well‐documented instances of tree damage during strong earthquakes, drawing inferences about local ground motions.

The Seismic Record↗

USGS2026

Earthquake rupture arrest from depth‐dependent frictional stability on the Pütürge segment of the East Anatolian Fault Zone, Türkiye (Turkey)

Determining why earthquake ruptures stop is a central challenge in earthquake science and seismic hazard assessment. The Pütürge segment of the East Anatolian Fault Zone, Türkiye, exhibits shallow creep (<∼3 km depth) yet hosts M > 6.5 earthquake ruptures at greater depth. Here, we evaluate whether variations in frictional stability along this segment aided arrest of the 2020 M 6.7 Elaziğ and 2023 M 7.8 Pazarcık earthquake ruptures. Analysis of Sentinel‐1 Synthetic Aperture Radar imagery indicates the 2023 M 7.8 rupture propagated laterally into a metamorphic massif within the Pütürge segment, where slip rapidly decayed below detection limits. Creepmeters along this segment recorded no significant surface afterslip (<3 mm) in the following year. To investigate this fault‐slip behavior, we conducted triaxial friction experiments on Pütürge fault gouge sampled from an outcrop exposure. The gouge, composed primarily of muscovite, quartz, and calcite, is velocity strengthening at conditions approximating 0–2.5 km depth and velocity weakening at 4–5 km depth. This transition to velocity‐weakening friction is associated with enhanced comminution and shear localization observed microstructurally. Our results suggest that depth‐dependent frictional stability of the Pütürge fault segment facilitates rupture nucleation and propagation at depth while maintaining rupture‐arresting behavior near Earth’s surface.

Pütürge segment of the East Anatolian Fault Zone↗

USGS2026

New constraints on northeast Seattle basin structure from converted seismic waves

The Seattle basin is a deep sedimentary basin in the Seattle–Bellevue, Washington metropolitan area within the Puget Lowland of Washington State. We determine the structure of a portion of the basin and the underlying basement using analysis of P waves converted from direct S incident from below. A deep local crustal event beneath Monroe, about 35 km northeast of Seattle, was recorded by a 100‐station nodal array deployed in 2019. The event produced a variety of coherent seismic phases, including converted waves from the sediment—basement boundary, internal structure within the basin, and additional crustal discontinuities. Using observed Sp converted waves, we apply an adjoint‐based full waveform inversion (FWI) method to determine the amplitude and extent of seismic discontinuities at depth. We find the strongest source of converted waves for this event lies ∼6 to 7 km depth below northern Lake Washington, interpreted to be the local depth to basement rock. The newly imaged shallow basement structure may be part of a deformation zone associated with the Siletzia eastern boundary. Our results highlight the utility of converted seismic waves recorded by a dense array, combined with an FWI method, to illuminate crustal structure.

Washington↗