Geology Reports⌕ Search
Home/Archive/USGS

USGS · 70226481

Measurement of ultrasonic velocities in solids under hydrostatic pressure

L. Peselnick
View original source ↗Export metadata ↓

Abstract

An ultrasonic method for determining velocity has been developed that is independent of phase‐change errors due to reflection of specimen waves from coupling films. The method also eliminates the possibility of error due to conditions of nonhydrostatic stress at a specimen‐transducer or specimen‐delay line interface. Preliminary data are given for Alcoa 2024‐T4 aluminum and are compared with results using the phase‐comparison method.

Explore related subjects

Journal of the Acoustical Society of AmericaArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

L. Peselnick. 1970. Measurement of ultrasonic velocities in solids under hydrostatic pressure. https://doi.org/10.1121/1.1912281

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2025

Investigation of surficial seabed heterogeneity and geoacoustic variability in the New England Mud Patch

Benthic biological processes influence seabed heterogeneity and contribute to vari- ability in geoacoustic properties. To investigate these relationships, measurements were conducted to quantify spatial variability in the upper few decimeters of sediment near the water-seabed interface within a fine-grained sediment deposit on the New England continental shelf. At each measurement location, an acoustic multicorer was deployed to sample the seabed. Acoustic probes were inserted into the sediment to collect direct in situ measurements of sediment compressional wave speed and attenuation (30–100 kHz) at near-ambient conditions, after which cores were collected from the inter-probe propagation paths. Sediment physical properties, organic carbon, infaunal community composition, and ex situ compressional wave speed and attenuation spanning two frequency decades (10 4 –10 6 Hz) were subsequently measured in the laboratory. The frequency dependence of sound speed ratio and attenuation was analyzed in the context of sediment acoustics models for mud based on the viscous grain shearing and extended Biot models. Sites with greater abundance of larger- bodied infauna (>1 mm) displayed higher variability in sound speed and attenuation. Correlation was found between sediment compressional wave modulus and total organic carbon, suggesting that organic matter in the sediment matrix also affects bulk acoustic properties.

New England Mud Patch↗
USGS2024

Direct measurements of sediment geoacoustic properties in the New England Mud Patch and shelf break

This paper reports on an original set of direct sound speed measurements collected with the acoustic coring system in the New England Mud Patch (NEMP) and shelf break area to the south. Cores collected within the NEMP show range-dependence of the mud with slower sound speed and lower attenuation on the west side. In the shelf break region, the highest sound speeds are observed between the 200- and 350-m isobaths. The depth-dependence of the mud layer in the NEMP includes a surficial layer with a negative sound speed gradient of 28 s −1 . The remainder of the mud column has a weak positive sound speed gradient of 6.2 s −1 over an isovelocity layer. Comparison between in situ and ex situ sound speed measurements provides an assessment of the effects of sediment disturbance from gravity coring operations. Small differences in the upper 2.5 m were attributed to the changes in the geoacoustic properties caused by disturbance from the coring process. Below 2.5 m, the average difference is close to zero, suggesting that these sediments were minimally disturbed. Finally, an in situ measurement of shear speed was obtained near the depth of maximum penetration. The shear speed was well correlated with sound speed from approximately the same depth interval.

New England Mud Patch↗
USGS2024

Feature-based maximum entropy for geophysical properties of the seabed

The coherent recombination of a direct and seabed reflected path is sensitive to the geophysical properties of the seabed. The concept of feature-based inversion is used in the analysis of acoustic data collected on a vertical line array (VLA) on the New England continental shelf break in about 200 m of water. The analysis approach for the measurements is based on a ray approach in which a direct and bottom reflected path is recombined, resulting in constructive and destructive interference of the acoustic amplitudes with frequency. The acoustic features have the form of prominent nulls of the measured received levels as a function of frequency as a broadband (500–4500 Hz) source passes the closest point of approach to the VLA. The viscous grain shearing (VGS) model is employed to parameterize a two-layer seabed model. The most likely seabed is a sand sediment with a porosity of about 0.42. There is a possibility of a thin (less than 0.5 m) surface layer having a slightly higher porosity between 0.45 and 0.50. Using the estimates for the VGS parameters inferred from the short-range frequency features, a normal mode model is used to predict the received acoustic levels over larger range scales.

Journal of the Acoustical Society of America↗