Geology ReportsSearch

USGS · 70188694

Daily reservoir sedimentation model: Case study from the Fena Valley Reservoir, Guam

Abstract

A model to compute reservoir sedimentation rates at daily timescales is presented. The model uses streamflow and sediment load data from nearby stream gauges to obtain an initial estimate of sediment yield for the reservoir’s watershed; it is then calibrated to the total deposition calculated from repeat bathymetric surveys. Long-term changes to reservoir trapping efficiency are also taken into account. The model was applied to the Fena Valley Reservoir, a water supply reservoir on the island of Guam. This reservoir became operational in 1951 and was recently surveyed in 2014. The model results show that the highest rate of deposition occurred during two typhoons (Typhoon Alice in 1953 and Typhoon Tingting in 2004); each storm decreased reservoir capacity by approximately 2–3% in only a few days. The presented model can be used to evaluate the impact of an extreme event, or it can be coupled with a watershed runoff model to evaluate potential impacts to storage capacity as a result of climate change or other hydrologic modifications.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Mathieu D. Marineau, Scott Wright. 2017. Daily reservoir sedimentation model: Case study from the Fena Valley Reservoir, Guam. https://doi.org/10.1061/(asce)hy.1943-7900.0001344

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Discharge estimation using video recordings from small unoccupied aircraft systems

Measurement of river discharge during flooding events has especially been a challenging and dangerous task in the southwestern US, where flows can be flashy, laden with sediment, and at high velocity. Small unoccupied aircraft systems (sUAS) can be deployed to access unsafe field sites and capture imagery for measuring surface flow velocity and discharge. This paper compares flow discharge estimation at eight field sites—located at or near USGS gauging stations—using time-averaged surface velocities and the turbulence dissipation rate (TDR) derived from large-scale particle image velocimetry (LSPIV) analysis of sUAS videos with conventional measurement techniques conducted by professional USGS hydrographers. Sites characteristics include both natural and engineered channels. The conventional measured discharges were treated as the reference discharges for evaluating the accuracy of the LSPIV discharge estimates. This study evaluated four approaches to estimate the depth-averaged or cross-sectional averaged velocity: constant-velocity index, logarithmic law, power-law, and the entropy method. Results showed the discharges can be accurately calculated by using any of these methods, and that choice of method depended on width to depth ratios.

Journal of Hydraulic Engineering

Dynamic selection of exposure time for turbulent flow measurements

The selection of optimum sampling configurations to measure the aspects of turbulent flow of water depends on the variable being measured, the applied measurement technique, the degree of environmental noise, and flow characteristics in and near the sampling location. This work presents a method to dynamically select the exposure time (SET) during the flow-velocity measurement at each sampling location on the basis of the moving block bootstrap (MBB) technique. The MBB enables near real-time estimation of the confidence intervals and, subsequently, the COV for turbulence parameters. The dynamic SET method has been tested in this work using time series of synthetic turbulent flow-velocity signals. This method was implemented using actual flow-velocity signals recorded with acoustic Doppler velocity (ADVs) instruments and acoustic Doppler current profilers (ADCPs). The results obtained from the implementation of the dynamic SET method show that the sampling time to achieve a defined uncertainty threshold is not the same for different turbulence parameters. Consequently, using the dynamic SET method, the exposure time can be optimized to obtain the turbulence parameters with the required uncertainty level. The dynamic SET method can be implemented in the instrument’s data logger to dynamically select the exposure time during flow measurements for a given uncertainty of the required turbulence parameter.

Journal of Hydraulic Engineering

Effectiveness of submerged vanes for stabilizing streamside bluffs

The effectiveness of submerged vanes for stabilizing streamside bluffs varied over a 10-year monitoring period in a tributary to Lake Superior, United States. Submerged vanes are a river training device used to divert river flows away from eroding banks along meander bends and ultimately hold constant or reverse the direction of lateral migration. At the study site, the relatively steep slope, large substrate size, and flashy flow regime pushed the upper end of the design limitations of submerged vanes. Changes in channel location and morphology due to the vanes were monitored using repeat channel cross-section surveys along a 110-m reach. The vanes experienced 15 floods over the monitoring period. The two most damaging floods happened in the summer and fall of 2005 with annual exceedance probabilities of 7% and 6% respectively. A new data analysis method for rivers, using centroids of cross sections, was useful to track channel migration rapidly and objectively and, along with calculations of changes in bankfull channel size, provide metrics to describe channel change.

Journal of Hydraulic Engineering