Geology Reports⌕ Search
Home/Archive/USGS

USGS · 70156419

Using ground and intact coal Samples to evaluate hydrocarbon fate during supercritical CO 2 injection into coal beds: effects of particle size and coal moisture

Jon Kolak·Paul C. Hackley·Leslie F. Ruppert·Peter D. Warwick·Robert Burruss
View original source ↗Export metadata ↓

Abstract

To investigate the potential for mobilizing organic compounds from coal beds during geologic carbon dioxide (CO 2 ) storage (sequestration), a series of solvent extractions using dichloromethane (DCM) and using supercritical CO 2 (40 °C and 10 MPa) were conducted on a set of coal samples collected from Louisiana and Ohio. The coal samples studied range in rank from lignite A to high volatile A bituminous, and were characterized using proximate, ultimate, organic petrography, and sorption isotherm analyses. Sorption isotherm analyses of gaseous CO 2 and methane show a general increase in gas storage capacity with coal rank, consistent with findings from previous studies. In the solvent extractions, both dry, ground coal samples and moist, intact core plug samples were used to evaluate effects of variations in particle size and moisture content. Samples were spiked with perdeuterated surrogate compounds prior to extraction, and extracts were analyzed via gas chromatography–mass spectrometry. The DCM extracts generally contained the highest concentrations of organic compounds, indicating the existence of additional hydrocarbons within the coal matrix that were not mobilized during supercritical CO 2 extractions. Concentrations of aliphatic and aromatic compounds measured in supercritical CO 2 extracts of core plug samples generally are lower than concentrations in corresponding extracts of dry, ground coal samples, due to differences in particle size and moisture content. Changes in the amount of extracted compounds and in surrogate recovery measured during consecutive supercritical CO 2 extractions of core plug samples appear to reflect the transition from a water-wet to a CO 2 -wet system. Changes in coal core plug mass during supercritical CO 2 extraction range from 3.4% to 14%, indicating that a substantial portion of coal moisture is retained in the low-rank coal samples. Moisture retention within core plug samples, especially in low-rank coals, appears to inhibit accessibility of supercritical CO 2 to coal matrix porosity, limiting the extent to which hydrocarbons are mobilized. Conversely, the enhanced recovery of some surrogates from core plugs relative to dry, ground coal samples might indicate that, once mobilized, supercritical CO 2 is capable of transporting these constituents through coal beds. These results underscore the need for using intact coal samples, and for better characterization of forms of water in coal, to understand fate and transport of organic compounds during supercritical CO 2 injection into coal beds.

Explore related subjects

Energy & FuelsArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Jon Kolak, Paul C. Hackley, Leslie F. Ruppert, Peter D. Warwick, Robert Burruss. 2015-07-06. Using ground and intact coal Samples to evaluate hydrocarbon fate during supercritical CO 2 injection into coal beds: effects of particle size and coal moisture. https://doi.org/10.1021/ef502611d

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Permeability and compressibility of “seal” sediment overlying the B1 sand gas hydrate reservoir: Hydrate 02 Geo Data Well, Prudhoe Bay unit, Alaska North Slope

An important element in evaluating the viability of extracting methane from a gas hydrate-bearing reservoir is establishing the effectiveness of the overlying bounding sediment as a seal to prevent gas loss, to enable effective depressurization, and to prevent fluid from entering the reservoir during production. This laboratory study presents results for index properties (e.g., grain density, grain size, and liquid limit), compressibility and swelling indices, and permeability measurements on sediment overlying the gas hydrate-bearing reservoir that was the target of the recent JOGMEC-DOE-USGS collaborative gas hydrate production testing project on the Alaska North Slope (ANS). Sediment analyzed in this study was collected during pressure coring operations in the HYDRATE 02 Geo Data Well (GDW). The ∼6.1 m sediment interval recovered in Cores 13P and 14P (878.74–884.88 m measured depth, MD) exhibited heterogeneous sedimentologic characteristics at the centimeter scale, with sediments ranging from clay to thin silty-sand lithologies. Permeability measurements and index-property correlations indicate the interval’s overall in situ vertical permeability ranges from 0.2 to 3.6 microdarcy (μD). Results for compressibility ( C C = 0.255 ± 0.02) and swelling index ( C S = 0.04 ± 0.01) are consistent with estimates based on mineralogy and liquid limit correlations. Based on the measured compressibility, the ∼3 MPa increase in effective stress during the stable phase of depressurization-induced production is anticipated to have imposed 2.43 cm of compaction per meter in the reservoir overburden, reducing permeability by ∼36%. The overburden sediment’s low in situ permeability (3 to 4 orders of magnitude below permeabilities measured in the gas hydrate-bearing part of the B1 sand (unit B)) suggests the B1 sand′s overburden provides an effective seal. Such a seal promotes efficient production by limiting fluid flow into the reservoir during depressurization-induced gas hydrate dissociation.

Alaska↗
USGS2026

Strength, stiffness, and Poisson’s ratio measurements for cements used in the well completions for the extended-duration gas production test on the Alaskan North Slope

As part of an extended-duration production test from a natural gas hydrate reservoir on the Alaska North Slope, a suite of optical-fiber sensors was encased in the completion cement to provide stable downhole monitoring around each of the four project wells. How the sensors respond to changes in the reservoir over time depends in part on properties of the LiteCRETE, ArcticCem, or Tuned Light cement in which each sensor is encased, and on how well the cement bonded to the well casing, sensors, and sediment formation. Here, we report on physical properties of the cements (compressive and tensile strength, stiffness, and Poisson’s ratio), on the downhole distribution of the cements used in each well, and on the cement bond quality. Physical property measurements are presented for cements sampled during the completion activities for the three wells completed in 2022–2023. Samples were cured while being submerged in water at 2–4 °C, then tested at intervals from ∼30 days to more than one year. After an initial period of rapid increase, cement strengths largely stabilized around 120 days in all cases, meaning that cements in all wells reached their nominal strength plateau four months or more before the production test began. Calculations based on recorded volumes of pumped cement show the subpermafrost, main hole portion of each well is encased only in the higher-density “tail” cement used in that well. Downhole cement evaluation logs from two wells demonstrate how the presence of sensors and other hardware outside the casing interferes with the cement evaluation assessment. Nonetheless, the cement evaluations indicate a generally good bond with the formation and sensors over the gas hydrate reservoir intervals.

Alaska↗
USGS2026

Oil in the Alaska North Slope gas hydrate reservoir: Micro-CT and flow simulation insights into permeability

Gas hydrate-bearing sands on the Alaska North Slope (ANS) host minor volumes of crude oil whose impact on formation permeability has never been quantified relative to a gas hydrate reservoir system. Here, we combine in situ pressure-core microcomputed-tomography (μ-CT), thermogravimetric analysis (TGA), gas-chromatography–mass-spectrometry (GC–MS), scanning-electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), and Stokes-flow simulation to (i) quantify oil saturation, (ii) infer its source, and (iii) evaluate its influence on permeability after gas-hydrate dissociation. μ-CT and SEM-EDS imaging identify the host sediment as silty, with some grain-coating clay present. Eight representative 300 3 -voxel subvolumes extracted from a preserved pressure core (Core 15P-3c, from the B1 sand (unit B), HYDRATE 02 Geo Data Well (GDW), 886.96–887.29 m measured depth, MD) exhibit porosities of 0.34–0.37 and an average oil saturation of 0.09 ± 0.03, in comparison to an independent TGA-based estimate of 0.16. GC-MS fingerprints obtained from an adjacent depressurized core (Core 17P-1, 891.37–891.44 m MD), together with oil pore habit revealed by μ-CT, suggest that the oil is partly native but also includes contributions from mineral oil-based drilling fluid contamination. Further analysis of oil–porewater interactions and flushing tests confirms that native oil saturation in the analyzed samples ranges from 0.04 to 0.08 with an average of approximately 0.06, and the oil is highly immobile. Flow simulations demonstrate that the native oil saturation of ≈0.06 reduces permeability by approximately 50% due to both pore blockage and increased flow-path tortuosity. These findings reveal the potential presence of native oil within the ANS gas hydrate reservoir and suggest that future simulation models may need to account for its impact on permeability to improve long-term performance predictions of gas and water production.

Alaska↗